5 files changed, 53 insertions, 5 deletions

diff --git a/include/linux/amba/bus.h b/include/linux/amba/bus.h
index 8b1038607831..b0c174012436 100644
--- a/include/linux/amba/bus.h
+++ b/include/linux/amba/bus.h
@@ -14,14 +14,19 @@
 #ifndef ASMARM_AMBA_H
 #define ASMARM_AMBA_H
 
+#include <linux/clk.h>
 #include <linux/device.h>
+#include <linux/err.h>
 #include <linux/resource.h>
 
 #define AMBA_NR_IRQS    2
 
+struct clk;
+
 struct amba_device {
         struct device           dev;
         struct resource         res;
+        struct clk              *pclk;
         u64                     dma_mask;
         unsigned int            periphid;
         unsigned int            irq[AMBA_NR_IRQS];
@@ -59,6 +64,12 @@ struct amba_device *amba_find_device(const char *, struct device *, unsigned int
 int amba_request_regions(struct amba_device *, const char *);
 void amba_release_regions(struct amba_device *);
 
+#define amba_pclk_enable(d)     \
+        (IS_ERR((d)->pclk) ? 0 : clk_enable((d)->pclk))
+
+#define amba_pclk_disable(d)    \
+        do { if (!IS_ERR((d)->pclk)) clk_disable((d)->pclk); } while (0)
+
 #define amba_config(d)  (((d)->periphid >> 24) & 0xff)
 #define amba_rev(d)     (((d)->periphid >> 20) & 0x0f)
 #define amba_manf(d)    (((d)->periphid >> 12) & 0xff)
diff --git a/include/linux/amba/mmci.h b/include/linux/amba/mmci.h
index 7e466fe72025..ca84ce70d5d5 100644
--- a/include/linux/amba/mmci.h
+++ b/include/linux/amba/mmci.h
@@ -15,9 +15,10 @@
  * @ocr_mask: available voltages on the 4 pins from the block, this
  * is ignored if a regulator is used, see the MMC_VDD_* masks in
  * mmc/host.h
- * @translate_vdd: a callback function to translate a MMC_VDD_*
- * mask into a value to be binary or:ed and written into the
- * MMCIPWR register of the block
+ * @vdd_handler: a callback function to translate a MMC_VDD_*
+ * mask into a value to be binary (or set some other custom bits
+ * in MMCIPWR) or:ed and written into the MMCIPWR register of the
+ * block.  May also control external power based on the power_mode.
  * @status: if no GPIO read function was given to the block in
  * gpio_wp (below) this function will be called to determine
  * whether a card is present in the MMC slot or not
@@ -29,7 +30,8 @@
 struct mmci_platform_data {
         unsigned int f_max;
         unsigned int ocr_mask;
-        u32 (*translate_vdd)(struct device *, unsigned int);
+        u32 (*vdd_handler)(struct device *, unsigned int vdd,
+                           unsigned char power_mode);
         unsigned int (*status)(struct device *);
         int     gpio_wp;
         int     gpio_cd;
diff --git a/include/linux/amba/serial.h b/include/linux/amba/serial.h
index 5a5a7fd62490..e1b634b635f2 100644
--- a/include/linux/amba/serial.h
+++ b/include/linux/amba/serial.h
@@ -38,10 +38,12 @@
 #define UART01x_FR              0x18    /* Flag register (Read only). */
 #define UART010_IIR             0x1C    /* Interrupt indentification register (Read). */
 #define UART010_ICR             0x1C    /* Interrupt clear register (Write). */
+#define ST_UART011_LCRH_RX      0x1C    /* Rx line control register. */
 #define UART01x_ILPR            0x20    /* IrDA low power counter register. */
 #define UART011_IBRD            0x24    /* Integer baud rate divisor register. */
 #define UART011_FBRD            0x28    /* Fractional baud rate divisor register. */
 #define UART011_LCRH            0x2c    /* Line control register. */
+#define ST_UART011_LCRH_TX      0x2c    /* Tx Line control register. */
 #define UART011_CR              0x30    /* Control register. */
 #define UART011_IFLS            0x34    /* Interrupt fifo level select. */
 #define UART011_IMSC            0x38    /* Interrupt mask. */
@@ -84,6 +86,7 @@
 #define UART010_CR_TIE          0x0020
 #define UART010_CR_RIE          0x0010
 #define UART010_CR_MSIE         0x0008
+#define ST_UART011_CR_OVSFACT   0x0008  /* Oversampling factor */
 #define UART01x_CR_IIRLP        0x0004  /* SIR low power mode */
 #define UART01x_CR_SIREN        0x0002  /* SIR enable */
 #define UART01x_CR_UARTEN       0x0001  /* UART enable */
diff --git a/include/linux/omapfb.h b/include/linux/omapfb.h
index 9bdd91486b49..7e4cd616bcb5 100644
--- a/include/linux/omapfb.h
+++ b/include/linux/omapfb.h
@@ -253,7 +253,7 @@ struct omapfb_platform_data {
 /* in arch/arm/plat-omap/fb.c */
 extern void omapfb_set_platform_data(struct omapfb_platform_data *data);
 extern void omapfb_set_ctrl_platform_data(void *pdata);
-extern void omapfb_reserve_sdram(void);
+extern void omapfb_reserve_sdram_memblock(void);
 
 #endif
 
diff --git a/include/linux/regulator/tps6507x.h b/include/linux/regulator/tps6507x.h
new file mode 100644
index 000000000000..4892f591bab1
--- /dev/null
+++ b/include/linux/regulator/tps6507x.h
@@ -0,0 +1,32 @@
+/*
+ * tps6507x.h  --  Voltage regulation for the Texas Instruments TPS6507X
+ *
+ * Copyright (C) 2010 Texas Instruments, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307 USA
+ */
+
+#ifndef REGULATOR_TPS6507X
+#define REGULATOR_TPS6507X
+
+/**
+ * tps6507x_reg_platform_data - platform data for tps6507x
+ * @defdcdc_default: Defines whether DCDC high or the low register controls
+ *      output voltage by default. Valid for DCDC2 and DCDC3 outputs only.
+ */
+struct tps6507x_reg_platform_data {
+        bool defdcdc_default;
+};
+
+#endif