1 files changed, 66 insertions, 71 deletions

diff --git a/include/linux/usb.h b/include/linux/usb.h
index 739f1fd1cc15..d5922a877994 100644
--- a/include/linux/usb.h
+++ b/include/linux/usb.h
@@ -45,27 +45,14 @@ struct wusb_dev;
 
 struct ep_device;
 
-/* For SS devices */
-/**
- * struct usb_host_ss_ep_comp - Valid for SuperSpeed devices only
- * @desc: endpoint companion descriptor, wMaxPacketSize in native byteorder
- * @extra: descriptors following this endpoint companion descriptor
- * @extralen: how many bytes of "extra" are valid
- */
-struct usb_host_ss_ep_comp {
-        struct usb_ss_ep_comp_descriptor        desc;
-        unsigned char                           *extra;   /* Extra descriptors */
-        int                                     extralen;
-};
-
 /**
  * struct usb_host_endpoint - host-side endpoint descriptor and queue
  * @desc: descriptor for this endpoint, wMaxPacketSize in native byteorder
+ * @ss_ep_comp: SuperSpeed companion descriptor for this endpoint
  * @urb_list: urbs queued to this endpoint; maintained by usbcore
  * @hcpriv: for use by HCD; typically holds hardware dma queue head (QH)
  *      with one or more transfer descriptors (TDs) per urb
  * @ep_dev: ep_device for sysfs info
- * @ss_ep_comp: companion descriptor information for this endpoint
  * @extra: descriptors following this endpoint in the configuration
  * @extralen: how many bytes of "extra" are valid
  * @enabled: URBs may be submitted to this endpoint
@@ -74,11 +61,11 @@ struct usb_host_ss_ep_comp {
  * descriptor within an active interface in a given USB configuration.
  */
 struct usb_host_endpoint {
-        struct usb_endpoint_descriptor  desc;
+        struct usb_endpoint_descriptor          desc;
+        struct usb_ss_ep_comp_descriptor        ss_ep_comp;
         struct list_head                urb_list;
         void                            *hcpriv;
-        struct ep_device                *ep_dev;        /* For sysfs info */
-        struct usb_host_ss_ep_comp      *ss_ep_comp;    /* For SS devices */
+        struct ep_device                *ep_dev;        /* For sysfs info */
 
         unsigned char *extra;   /* Extra descriptors */
         int extralen;
@@ -109,8 +96,8 @@ enum usb_interface_condition {
 /**
  * struct usb_interface - what usb device drivers talk to
  * @altsetting: array of interface structures, one for each alternate
- *      setting that may be selected.  Each one includes a set of
- *      endpoint configurations.  They will be in no particular order.
+ *      setting that may be selected.  Each one includes a set of
+ *      endpoint configurations.  They will be in no particular order.
  * @cur_altsetting: the current altsetting.
  * @num_altsetting: number of altsettings defined.
  * @intf_assoc: interface association descriptor
@@ -197,8 +184,6 @@ struct usb_interface {
         struct work_struct reset_ws;    /* for resets in atomic context */
 };
 #define to_usb_interface(d) container_of(d, struct usb_interface, dev)
-#define interface_to_usbdev(intf) \
-        container_of(intf->dev.parent, struct usb_device, dev)
 
 static inline void *usb_get_intfdata(struct usb_interface *intf)
 {
@@ -215,7 +200,7 @@ void usb_put_intf(struct usb_interface *intf);
 
 /* this maximum is arbitrary */
 #define USB_MAXINTERFACES       32
-#define USB_MAXIADS             USB_MAXINTERFACES/2
+#define USB_MAXIADS             (USB_MAXINTERFACES/2)
 
 /**
  * struct usb_interface_cache - long-term representation of a device interface
@@ -425,7 +410,6 @@ struct usb_tt;
  * @connect_time: time device was first connected
  * @do_remote_wakeup:  remote wakeup should be enabled
  * @reset_resume: needs reset instead of resume
- * @autosuspend_disabled: autosuspend disabled by the user
  * @wusb_dev: if this is a Wireless USB device, link to the WUSB
  *      specific data for the device.
  * @slot_id: Slot ID assigned by xHCI
@@ -436,7 +420,7 @@ struct usb_tt;
  */
 struct usb_device {
         int             devnum;
-        char            devpath [16];
+        char            devpath[16];
         u32             route;
         enum usb_device_state   state;
         enum usb_device_speed   speed;
@@ -469,7 +453,7 @@ struct usb_device {
         unsigned persist_enabled:1;
         unsigned have_langid:1;
         unsigned authorized:1;
-        unsigned authenticated:1;
+        unsigned authenticated:1;
         unsigned wusb:1;
         int string_langid;
 
@@ -501,13 +485,17 @@ struct usb_device {
 
         unsigned do_remote_wakeup:1;
         unsigned reset_resume:1;
-        unsigned autosuspend_disabled:1;
 #endif
         struct wusb_dev *wusb_dev;
         int slot_id;
 };
 #define to_usb_device(d) container_of(d, struct usb_device, dev)
 
+static inline struct usb_device *interface_to_usbdev(struct usb_interface *intf)
+{
+        return to_usb_device(intf->dev.parent);
+}
+
 extern struct usb_device *usb_get_dev(struct usb_device *dev);
 extern void usb_put_dev(struct usb_device *dev);
 
@@ -522,12 +510,11 @@ extern int usb_lock_device_for_reset(struct usb_device *udev,
 extern int usb_reset_device(struct usb_device *dev);
 extern void usb_queue_reset_device(struct usb_interface *dev);
 
-extern struct usb_device *usb_find_device(u16 vendor_id, u16 product_id);
 
 /* USB autosuspend and autoresume */
 #ifdef CONFIG_USB_SUSPEND
-extern int usb_enable_autosuspend(struct usb_device *udev);
-extern int usb_disable_autosuspend(struct usb_device *udev);
+extern void usb_enable_autosuspend(struct usb_device *udev);
+extern void usb_disable_autosuspend(struct usb_device *udev);
 
 extern int usb_autopm_get_interface(struct usb_interface *intf);
 extern void usb_autopm_put_interface(struct usb_interface *intf);
@@ -572,6 +559,16 @@ static inline void usb_mark_last_busy(struct usb_device *udev)
 /* for drivers using iso endpoints */
 extern int usb_get_current_frame_number(struct usb_device *usb_dev);
 
+/* Sets up a group of bulk endpoints to support multiple stream IDs. */
+extern int usb_alloc_streams(struct usb_interface *interface,
+                struct usb_host_endpoint **eps, unsigned int num_eps,
+                unsigned int num_streams, gfp_t mem_flags);
+
+/* Reverts a group of bulk endpoints back to not using stream IDs. */
+extern void usb_free_streams(struct usb_interface *interface,
+                struct usb_host_endpoint **eps, unsigned int num_eps,
+                gfp_t mem_flags);
+
 /* used these for multi-interface device registration */
 extern int usb_driver_claim_interface(struct usb_driver *driver,
                         struct usb_interface *iface, void *priv);
@@ -667,7 +664,7 @@ static inline int usb_make_path(struct usb_device *dev, char *buf, size_t size)
  * This macro is used to create a struct usb_device_id that matches a
  * specific device.
  */
-#define USB_DEVICE(vend,prod) \
+#define USB_DEVICE(vend, prod) \
         .match_flags = USB_DEVICE_ID_MATCH_DEVICE, \
         .idVendor = (vend), \
         .idProduct = (prod)
@@ -958,17 +955,25 @@ extern int usb_disabled(void);
 #define URB_ISO_ASAP            0x0002  /* iso-only, urb->start_frame
                                          * ignored */
 #define URB_NO_TRANSFER_DMA_MAP 0x0004  /* urb->transfer_dma valid on submit */
-#define URB_NO_SETUP_DMA_MAP    0x0008  /* urb->setup_dma valid on submit */
 #define URB_NO_FSBR             0x0020  /* UHCI-specific */
 #define URB_ZERO_PACKET         0x0040  /* Finish bulk OUT with short packet */
 #define URB_NO_INTERRUPT        0x0080  /* HINT: no non-error interrupt
                                          * needed */
 #define URB_FREE_BUFFER         0x0100  /* Free transfer buffer with the URB */
 
+/* The following flags are used internally by usbcore and HCDs */
 #define URB_DIR_IN              0x0200  /* Transfer from device to host */
 #define URB_DIR_OUT             0
 #define URB_DIR_MASK            URB_DIR_IN
 
+#define URB_DMA_MAP_SINGLE      0x00010000      /* Non-scatter-gather mapping */
+#define URB_DMA_MAP_PAGE        0x00020000      /* HCD-unsupported S-G */
+#define URB_DMA_MAP_SG          0x00040000      /* HCD-supported S-G */
+#define URB_MAP_LOCAL           0x00080000      /* HCD-local-memory mapping */
+#define URB_SETUP_MAP_SINGLE    0x00100000      /* Setup packet DMA mapped */
+#define URB_SETUP_MAP_LOCAL     0x00200000      /* HCD-local setup packet */
+#define URB_DMA_SG_COMBINED     0x00400000      /* S-G entries were combined */
+
 struct usb_iso_packet_descriptor {
         unsigned int offset;
         unsigned int length;            /* expected length */
@@ -1045,12 +1050,8 @@ typedef void (*usb_complete_t)(struct urb *);
  * @setup_packet: Only used for control transfers, this points to eight bytes
  *      of setup data.  Control transfers always start by sending this data
  *      to the device.  Then transfer_buffer is read or written, if needed.
- * @setup_dma: For control transfers with URB_NO_SETUP_DMA_MAP set, the
- *      device driver has provided this DMA address for the setup packet.
- *      The host controller driver should use this in preference to
- *      setup_packet, but the HCD may chose to ignore the address if it must
- *      copy the setup packet into internal structures.  Therefore, setup_packet
- *      must always point to a valid buffer.
+ * @setup_dma: DMA pointer for the setup packet.  The caller must not use
+ *      this field; setup_packet must point to a valid buffer.
  * @start_frame: Returns the initial frame for isochronous transfers.
  * @number_of_packets: Lists the number of ISO transfer buffers.
  * @interval: Specifies the polling interval for interrupt or isochronous
@@ -1082,13 +1083,14 @@ typedef void (*usb_complete_t)(struct urb *);
  * bounce buffer or talking to an IOMMU),
  * although they're cheap on commodity x86 and ppc hardware.
  *
- * Alternatively, drivers may pass the URB_NO_xxx_DMA_MAP transfer flags,
- * which tell the host controller driver that no such mapping is needed since
+ * Alternatively, drivers may pass the URB_NO_TRANSFER_DMA_MAP transfer flag,
+ * which tells the host controller driver that no such mapping is needed for
+ * the transfer_buffer since
  * the device driver is DMA-aware.  For example, a device driver might
  * allocate a DMA buffer with usb_alloc_coherent() or call usb_buffer_map().
- * When these transfer flags are provided, host controller drivers will
- * attempt to use the dma addresses found in the transfer_dma and/or
- * setup_dma fields rather than determining a dma address themselves.
+ * When this transfer flag is provided, host controller drivers will
+ * attempt to use the dma address found in the transfer_dma
+ * field rather than determining a dma address themselves.
  *
  * Note that transfer_buffer must still be set if the controller
  * does not support DMA (as indicated by bus.uses_dma) and when talking
@@ -1111,11 +1113,9 @@ typedef void (*usb_complete_t)(struct urb *);
  * should always terminate with a short packet, even if it means adding an
  * extra zero length packet.
  *
- * Control URBs must provide a setup_packet.  The setup_packet and
- * transfer_buffer may each be mapped for DMA or not, independently of
- * the other.  The transfer_flags bits URB_NO_TRANSFER_DMA_MAP and
- * URB_NO_SETUP_DMA_MAP indicate which buffers have already been mapped.
- * URB_NO_SETUP_DMA_MAP is ignored for non-control URBs.
+ * Control URBs must provide a valid pointer in the setup_packet field.
+ * Unlike the transfer_buffer, the setup_packet may not be mapped for DMA
+ * beforehand.
  *
  * Interrupt URBs must provide an interval, saying how often (in milliseconds
  * or, for highspeed devices, 125 microsecond units)
@@ -1186,14 +1186,15 @@ struct urb {
                                          * current owner */
         struct list_head anchor_list;   /* the URB may be anchored */
         struct usb_anchor *anchor;
-        struct usb_device *dev;         /* (in) pointer to associated device */
+        struct usb_device *dev;         /* (in) pointer to associated device */
         struct usb_host_endpoint *ep;   /* (internal) pointer to endpoint */
         unsigned int pipe;              /* (in) pipe information */
+        unsigned int stream_id;         /* (in) stream ID */
         int status;                     /* (return) non-ISO status */
         unsigned int transfer_flags;    /* (in) URB_SHORT_NOT_OK | ...*/
         void *transfer_buffer;          /* (in) associated data buffer */
         dma_addr_t transfer_dma;        /* (in) dma addr for transfer_buffer */
-        struct usb_sg_request *sg;      /* (in) scatter gather buffer list */
+        struct scatterlist *sg;         /* (in) scatter gather buffer list */
         int num_sgs;                    /* (in) number of entries in the sg list */
         u32 transfer_buffer_length;     /* (in) data buffer length */
         u32 actual_length;              /* (return) actual transfer length */
@@ -1371,18 +1372,6 @@ void *usb_alloc_coherent(struct usb_device *dev, size_t size,
 void usb_free_coherent(struct usb_device *dev, size_t size,
         void *addr, dma_addr_t dma);
 
-/* Compatible macros while we switch over */
-static inline void *usb_buffer_alloc(struct usb_device *dev, size_t size,
-                                     gfp_t mem_flags, dma_addr_t *dma)
-{
-        return usb_alloc_coherent(dev, size, mem_flags, dma);
-}
-static inline void usb_buffer_free(struct usb_device *dev, size_t size,
-                                   void *addr, dma_addr_t dma)
-{
-        return usb_free_coherent(dev, size, addr, dma);
-}
-
 #if 0
 struct urb *usb_buffer_map(struct urb *urb);
 void usb_buffer_dmasync(struct urb *urb);
@@ -1467,8 +1456,6 @@ struct usb_sg_request {
 
         struct usb_device       *dev;
         int                     pipe;
-        struct scatterlist      *sg;
-        int                     nents;
 
         int                     entries;
         struct urb              **urbs;
@@ -1536,23 +1523,31 @@ static inline unsigned int __create_pipe(struct usb_device *dev,
 }
 
 /* Create various pipes... */
-#define usb_sndctrlpipe(dev,endpoint)   \
+#define usb_sndctrlpipe(dev, endpoint)  \
         ((PIPE_CONTROL << 30) | __create_pipe(dev, endpoint))
-#define usb_rcvctrlpipe(dev,endpoint)   \
+#define usb_rcvctrlpipe(dev, endpoint)  \
         ((PIPE_CONTROL << 30) | __create_pipe(dev, endpoint) | USB_DIR_IN)
-#define usb_sndisocpipe(dev,endpoint)   \
+#define usb_sndisocpipe(dev, endpoint)  \
         ((PIPE_ISOCHRONOUS << 30) | __create_pipe(dev, endpoint))
-#define usb_rcvisocpipe(dev,endpoint)   \
+#define usb_rcvisocpipe(dev, endpoint)  \
         ((PIPE_ISOCHRONOUS << 30) | __create_pipe(dev, endpoint) | USB_DIR_IN)
-#define usb_sndbulkpipe(dev,endpoint)   \
+#define usb_sndbulkpipe(dev, endpoint)  \
         ((PIPE_BULK << 30) | __create_pipe(dev, endpoint))
-#define usb_rcvbulkpipe(dev,endpoint)   \
+#define usb_rcvbulkpipe(dev, endpoint)  \
         ((PIPE_BULK << 30) | __create_pipe(dev, endpoint) | USB_DIR_IN)
-#define usb_sndintpipe(dev,endpoint)    \
+#define usb_sndintpipe(dev, endpoint)   \
         ((PIPE_INTERRUPT << 30) | __create_pipe(dev, endpoint))
-#define usb_rcvintpipe(dev,endpoint)    \
+#define usb_rcvintpipe(dev, endpoint)   \
         ((PIPE_INTERRUPT << 30) | __create_pipe(dev, endpoint) | USB_DIR_IN)
 
+static inline struct usb_host_endpoint *
+usb_pipe_endpoint(struct usb_device *dev, unsigned int pipe)
+{
+        struct usb_host_endpoint **eps;
+        eps = usb_pipein(pipe) ? dev->ep_in : dev->ep_out;
+        return eps[usb_pipeendpoint(pipe)];
+}
+
 /*-------------------------------------------------------------------------*/
 
 static inline __u16