3 files changed, 44 insertions, 0 deletions

diff --git a/include/linux/spi/eeprom.h b/include/linux/spi/eeprom.h
index 1085212c446e..306e7b1c69ed 100644
--- a/include/linux/spi/eeprom.h
+++ b/include/linux/spi/eeprom.h
@@ -1,6 +1,8 @@
 #ifndef __LINUX_SPI_EEPROM_H
 #define __LINUX_SPI_EEPROM_H
 
+#include <linux/memory.h>
+
 /*
  * Put one of these structures in platform_data for SPI EEPROMS handled
  * by the "at25" driver.  On SPI, most EEPROMS understand the same core
@@ -17,6 +19,10 @@ struct spi_eeprom {
 #define EE_ADDR2        0x0002                  /* 16 bit addrs */
 #define EE_ADDR3        0x0004                  /* 24 bit addrs */
 #define EE_READONLY     0x0008                  /* disallow writes */
+
+        /* for exporting this chip's data to other kernel code */
+        void (*setup)(struct memory_accessor *mem, void *context);
+        void *context;
 };
 
 #endif /* __LINUX_SPI_EEPROM_H */
diff --git a/include/linux/spi/libertas_spi.h b/include/linux/spi/libertas_spi.h
new file mode 100644
index 000000000000..79506f5f9e67
--- /dev/null
+++ b/include/linux/spi/libertas_spi.h
@@ -0,0 +1,32 @@
+/*
+ * board-specific data for the libertas_spi driver.
+ *
+ * Copyright 2008 Analog Devices Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or (at
+ * your option) any later version.
+ */
+#ifndef _LIBERTAS_SPI_H_
+#define _LIBERTAS_SPI_H_
+
+struct spi_device;
+
+struct libertas_spi_platform_data {
+        /* There are two ways to read data from the WLAN module's SPI
+         * interface. Setting 0 or 1 here controls which one is used.
+         *
+         * Usually you want to set use_dummy_writes = 1.
+         * However, if that doesn't work or if you are using a slow SPI clock
+         * speed, you may want to use 0 here. */
+        u16 use_dummy_writes;
+
+        /* GPIO number to use as chip select */
+        u16 gpio_cs;
+
+        /* Board specific setup/teardown */
+        int (*setup)(struct spi_device *spi);
+        int (*teardown)(struct spi_device *spi);
+};
+#endif
diff --git a/include/linux/spi/spi_gpio.h b/include/linux/spi/spi_gpio.h
index 0f01a0f1f40c..ca6782ee4b9f 100644
--- a/include/linux/spi/spi_gpio.h
+++ b/include/linux/spi/spi_gpio.h
@@ -25,10 +25,16 @@
  *      ...
  *      };
  *
+ * If chipselect is not used (there's only one device on the bus), assign
+ * SPI_GPIO_NO_CHIPSELECT to the controller_data:
+ *              .controller_data = (void *) SPI_GPIO_NO_CHIPSELECT;
+ *
  * If the bitbanged bus is later switched to a "native" controller,
  * that platform_device and controller_data should be removed.
  */
 
+#define SPI_GPIO_NO_CHIPSELECT          ((unsigned long)-1l)
+
 /**
  * struct spi_gpio_platform_data - parameter for bitbanged SPI master
  * @sck: number of the GPIO used for clock output