1 files changed, 177 insertions, 33 deletions

diff --git a/include/linux/nl80211.h b/include/linux/nl80211.h
index 2c8701687336..0edb2566c14c 100644
--- a/include/linux/nl80211.h
+++ b/include/linux/nl80211.h
@@ -40,6 +40,43 @@
  */
 
 /**
+ * DOC: Frame transmission/registration support
+ *
+ * Frame transmission and registration support exists to allow userspace
+ * management entities such as wpa_supplicant react to management frames
+ * that are not being handled by the kernel. This includes, for example,
+ * certain classes of action frames that cannot be handled in the kernel
+ * for various reasons.
+ *
+ * Frame registration is done on a per-interface basis and registrations
+ * cannot be removed other than by closing the socket. It is possible to
+ * specify a registration filter to register, for example, only for a
+ * certain type of action frame. In particular with action frames, those
+ * that userspace registers for will not be returned as unhandled by the
+ * driver, so that the registered application has to take responsibility
+ * for doing that.
+ *
+ * The type of frame that can be registered for is also dependent on the
+ * driver and interface type. The frame types are advertised in wiphy
+ * attributes so applications know what to expect.
+ *
+ * NOTE: When an interface changes type while registrations are active,
+ *       these registrations are ignored until the interface type is
+ *       changed again. This means that changing the interface type can
+ *       lead to a situation that couldn't otherwise be produced, but
+ *       any such registrations will be dormant in the sense that they
+ *       will not be serviced, i.e. they will not receive any frames.
+ *
+ * Frame transmission allows userspace to send for example the required
+ * responses to action frames. It is subject to some sanity checking,
+ * but many frames can be transmitted. When a frame was transmitted, its
+ * status is indicated to the sending socket.
+ *
+ * For more technical details, see the corresponding command descriptions
+ * below.
+ */
+
+/**
  * enum nl80211_commands - supported nl80211 commands
  *
  * @NL80211_CMD_UNSPEC: unspecified command to catch errors
@@ -258,7 +295,9 @@
  *      auth and assoc steps. For this, you need to specify the SSID in a
  *      %NL80211_ATTR_SSID attribute, and can optionally specify the association
  *      IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_MAC,
- *      %NL80211_ATTR_WIPHY_FREQ and %NL80211_ATTR_CONTROL_PORT.
+ *      %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT,
+ *      %NL80211_ATTR_CONTROL_PORT_ETHERTYPE and
+ *      %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT.
  *      It is also sent as an event, with the BSSID and response IEs when the
  *      connection is established or failed to be established. This can be
  *      determined by the STATUS_CODE attribute.
@@ -276,8 +315,8 @@
  *      channel for the specified amount of time. This can be used to do
  *      off-channel operations like transmit a Public Action frame and wait for
  *      a response while being associated to an AP on another channel.
- *      %NL80211_ATTR_WIPHY or %NL80211_ATTR_IFINDEX is used to specify which
- *      radio is used. %NL80211_ATTR_WIPHY_FREQ is used to specify the
+ *      %NL80211_ATTR_IFINDEX is used to specify which interface (and thus
+ *      radio) is used. %NL80211_ATTR_WIPHY_FREQ is used to specify the
  *      frequency for the operation and %NL80211_ATTR_WIPHY_CHANNEL_TYPE may be
  *      optionally used to specify additional channel parameters.
  *      %NL80211_ATTR_DURATION is used to specify the duration in milliseconds
@@ -301,16 +340,20 @@
  *      rate selection. %NL80211_ATTR_IFINDEX is used to specify the interface
  *      and @NL80211_ATTR_TX_RATES the set of allowed rates.
  *
- * @NL80211_CMD_REGISTER_ACTION: Register for receiving certain action frames
- *      (via @NL80211_CMD_ACTION) for processing in userspace. This command
- *      requires an interface index and a match attribute containing the first
- *      few bytes of the frame that should match, e.g. a single byte for only
- *      a category match or four bytes for vendor frames including the OUI.
- *      The registration cannot be dropped, but is removed automatically
- *      when the netlink socket is closed. Multiple registrations can be made.
- * @NL80211_CMD_ACTION: Action frame TX request and RX notification. This
- *      command is used both as a request to transmit an Action frame and as an
- *      event indicating reception of an Action frame that was not processed in
+ * @NL80211_CMD_REGISTER_FRAME: Register for receiving certain mgmt frames
+ *      (via @NL80211_CMD_FRAME) for processing in userspace. This command
+ *      requires an interface index, a frame type attribute (optional for
+ *      backward compatibility reasons, if not given assumes action frames)
+ *      and a match attribute containing the first few bytes of the frame
+ *      that should match, e.g. a single byte for only a category match or
+ *      four bytes for vendor frames including the OUI. The registration
+ *      cannot be dropped, but is removed automatically when the netlink
+ *      socket is closed. Multiple registrations can be made.
+ * @NL80211_CMD_REGISTER_ACTION: Alias for @NL80211_CMD_REGISTER_FRAME for
+ *      backward compatibility
+ * @NL80211_CMD_FRAME: Management frame TX request and RX notification. This
+ *      command is used both as a request to transmit a management frame and
+ *      as an event indicating reception of a frame that was not processed in
  *      kernel code, but is for us (i.e., which may need to be processed in a
  *      user space application). %NL80211_ATTR_FRAME is used to specify the
  *      frame contents (including header). %NL80211_ATTR_WIPHY_FREQ (and
@@ -320,11 +363,14 @@
  *      operational channel). When called, this operation returns a cookie
  *      (%NL80211_ATTR_COOKIE) that will be included with the TX status event
  *      pertaining to the TX request.
- * @NL80211_CMD_ACTION_TX_STATUS: Report TX status of an Action frame
- *      transmitted with %NL80211_CMD_ACTION. %NL80211_ATTR_COOKIE identifies
+ * @NL80211_CMD_ACTION: Alias for @NL80211_CMD_FRAME for backward compatibility.
+ * @NL80211_CMD_FRAME_TX_STATUS: Report TX status of a management frame
+ *      transmitted with %NL80211_CMD_FRAME. %NL80211_ATTR_COOKIE identifies
  *      the TX command and %NL80211_ATTR_FRAME includes the contents of the
  *      frame. %NL80211_ATTR_ACK flag is included if the recipient acknowledged
  *      the frame.
+ * @NL80211_CMD_ACTION_TX_STATUS: Alias for @NL80211_CMD_FRAME_TX_STATUS for
+ *      backward compatibility.
  * @NL80211_CMD_SET_CQM: Connection quality monitor configuration. This command
  *      is used to configure connection quality monitoring notification trigger
  *      levels.
@@ -341,6 +387,8 @@
  *      of any other interfaces, and other interfaces will again take
  *      precedence when they are used.
  *
+ * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface.
+ *
  * @NL80211_CMD_MAX: highest used command number
  * @__NL80211_CMD_AFTER_LAST: internal use
  */
@@ -429,9 +477,12 @@ enum nl80211_commands {
 
         NL80211_CMD_SET_TX_BITRATE_MASK,
 
-        NL80211_CMD_REGISTER_ACTION,
-        NL80211_CMD_ACTION,
-        NL80211_CMD_ACTION_TX_STATUS,
+        NL80211_CMD_REGISTER_FRAME,
+        NL80211_CMD_REGISTER_ACTION = NL80211_CMD_REGISTER_FRAME,
+        NL80211_CMD_FRAME,
+        NL80211_CMD_ACTION = NL80211_CMD_FRAME,
+        NL80211_CMD_FRAME_TX_STATUS,
+        NL80211_CMD_ACTION_TX_STATUS = NL80211_CMD_FRAME_TX_STATUS,
 
         NL80211_CMD_SET_POWER_SAVE,
         NL80211_CMD_GET_POWER_SAVE,
@@ -440,6 +491,7 @@ enum nl80211_commands {
         NL80211_CMD_NOTIFY_CQM,
 
         NL80211_CMD_SET_CHANNEL,
+        NL80211_CMD_SET_WDS_PEER,
 
         /* add new commands above here */
 
@@ -639,6 +691,15 @@ enum nl80211_commands {
  *      request, the driver will assume that the port is unauthorized until
  *      authorized by user space. Otherwise, port is marked authorized by
  *      default in station mode.
+ * @NL80211_ATTR_CONTROL_PORT_ETHERTYPE: A 16-bit value indicating the
+ *      ethertype that will be used for key negotiation. It can be
+ *      specified with the associate and connect commands. If it is not
+ *      specified, the value defaults to 0x888E (PAE, 802.1X). This
+ *      attribute is also used as a flag in the wiphy information to
+ *      indicate that protocols other than PAE are supported.
+ * @NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT: When included along with
+ *      %NL80211_ATTR_CONTROL_PORT_ETHERTYPE, indicates that the custom
+ *      ethertype frames used for key negotiation must not be encrypted.
  *
  * @NL80211_ATTR_TESTDATA: Testmode data blob, passed through to the driver.
  *      We recommend using nested, driver-specific attributes within this.
@@ -708,7 +769,16 @@ enum nl80211_commands {
  *      is used with %NL80211_CMD_SET_TX_BITRATE_MASK.
  *
  * @NL80211_ATTR_FRAME_MATCH: A binary attribute which typically must contain
- *      at least one byte, currently used with @NL80211_CMD_REGISTER_ACTION.
+ *      at least one byte, currently used with @NL80211_CMD_REGISTER_FRAME.
+ * @NL80211_ATTR_FRAME_TYPE: A u16 indicating the frame type/subtype for the
+ *      @NL80211_CMD_REGISTER_FRAME command.
+ * @NL80211_ATTR_TX_FRAME_TYPES: wiphy capability attribute, which is a
+ *      nested attribute of %NL80211_ATTR_FRAME_TYPE attributes, containing
+ *      information about which frame types can be transmitted with
+ *      %NL80211_CMD_FRAME.
+ * @NL80211_ATTR_RX_FRAME_TYPES: wiphy capability attribute, which is a
+ *      nested attribute of %NL80211_ATTR_FRAME_TYPE attributes, containing
+ *      information about which frame types can be registered for RX.
  *
  * @NL80211_ATTR_ACK: Flag attribute indicating that the frame was
  *      acknowledged by the recipient.
@@ -731,6 +801,9 @@ enum nl80211_commands {
  *      This is used in association with @NL80211_ATTR_WIPHY_TX_POWER_SETTING
  *      for non-automatic settings.
  *
+ * @NL80211_ATTR_SUPPORT_IBSS_RSN: The device supports IBSS RSN, which mostly
+ *      means support for per-station GTKs.
+ *
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
  */
@@ -891,6 +964,15 @@ enum nl80211_attrs {
         NL80211_ATTR_WIPHY_TX_POWER_SETTING,
         NL80211_ATTR_WIPHY_TX_POWER_LEVEL,
 
+        NL80211_ATTR_TX_FRAME_TYPES,
+        NL80211_ATTR_RX_FRAME_TYPES,
+        NL80211_ATTR_FRAME_TYPE,
+
+        NL80211_ATTR_CONTROL_PORT_ETHERTYPE,
+        NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT,
+
+        NL80211_ATTR_SUPPORT_IBSS_RSN,
+
         /* add attributes here, update the policy in nl80211.c */
 
         __NL80211_ATTR_AFTER_LAST,
@@ -946,8 +1028,10 @@ enum nl80211_attrs {
  * @NL80211_IFTYPE_WDS: wireless distribution interface
  * @NL80211_IFTYPE_MONITOR: monitor interface receiving all frames
  * @NL80211_IFTYPE_MESH_POINT: mesh point
+ * @NL80211_IFTYPE_P2P_CLIENT: P2P client
+ * @NL80211_IFTYPE_P2P_GO: P2P group owner
  * @NL80211_IFTYPE_MAX: highest interface type number currently defined
- * @__NL80211_IFTYPE_AFTER_LAST: internal use
+ * @NUM_NL80211_IFTYPES: number of defined interface types
  *
  * These values are used with the %NL80211_ATTR_IFTYPE
  * to set the type of an interface.
@@ -962,10 +1046,12 @@ enum nl80211_iftype {
         NL80211_IFTYPE_WDS,
         NL80211_IFTYPE_MONITOR,
         NL80211_IFTYPE_MESH_POINT,
+        NL80211_IFTYPE_P2P_CLIENT,
+        NL80211_IFTYPE_P2P_GO,
 
         /* keep last */
-        __NL80211_IFTYPE_AFTER_LAST,
-        NL80211_IFTYPE_MAX = __NL80211_IFTYPE_AFTER_LAST - 1
+        NUM_NL80211_IFTYPES,
+        NL80211_IFTYPE_MAX = NUM_NL80211_IFTYPES - 1
 };
 
 /**
@@ -974,11 +1060,14 @@ enum nl80211_iftype {
  * Station flags. When a station is added to an AP interface, it is
  * assumed to be already associated (and hence authenticated.)
  *
+ * @__NL80211_STA_FLAG_INVALID: attribute number 0 is reserved
  * @NL80211_STA_FLAG_AUTHORIZED: station is authorized (802.1X)
  * @NL80211_STA_FLAG_SHORT_PREAMBLE: station is capable of receiving frames
  *      with short barker preamble
  * @NL80211_STA_FLAG_WME: station is WME/QoS capable
  * @NL80211_STA_FLAG_MFP: station uses management frame protection
+ * @NL80211_STA_FLAG_MAX: highest station flag number currently defined
+ * @__NL80211_STA_FLAG_AFTER_LAST: internal use
  */
 enum nl80211_sta_flags {
         __NL80211_STA_FLAG_INVALID,
@@ -1048,6 +1137,8 @@ enum nl80211_rate_info {
  * @NL80211_STA_INFO_RX_PACKETS: total received packet (u32, from this station)
  * @NL80211_STA_INFO_TX_PACKETS: total transmitted packets (u32, to this
  *      station)
+ * @NL80211_STA_INFO_TX_RETRIES: total retries (u32, to this station)
+ * @NL80211_STA_INFO_TX_FAILED: total failed packets (u32, to this station)
  */
 enum nl80211_sta_info {
         __NL80211_STA_INFO_INVALID,
@@ -1061,6 +1152,8 @@ enum nl80211_sta_info {
         NL80211_STA_INFO_TX_BITRATE,
         NL80211_STA_INFO_RX_PACKETS,
         NL80211_STA_INFO_TX_PACKETS,
+        NL80211_STA_INFO_TX_RETRIES,
+        NL80211_STA_INFO_TX_FAILED,
 
         /* keep last */
         __NL80211_STA_INFO_AFTER_LAST,
@@ -1091,14 +1184,17 @@ enum nl80211_mpath_flags {
  * information about a mesh path.
  *
  * @__NL80211_MPATH_INFO_INVALID: attribute number 0 is reserved
- * @NL80211_ATTR_MPATH_FRAME_QLEN: number of queued frames for this destination
- * @NL80211_ATTR_MPATH_SN: destination sequence number
- * @NL80211_ATTR_MPATH_METRIC: metric (cost) of this mesh path
- * @NL80211_ATTR_MPATH_EXPTIME: expiration time for the path, in msec from now
- * @NL80211_ATTR_MPATH_FLAGS: mesh path flags, enumerated in
+ * @NL80211_MPATH_INFO_FRAME_QLEN: number of queued frames for this destination
+ * @NL80211_MPATH_INFO_SN: destination sequence number
+ * @NL80211_MPATH_INFO_METRIC: metric (cost) of this mesh path
+ * @NL80211_MPATH_INFO_EXPTIME: expiration time for the path, in msec from now
+ * @NL80211_MPATH_INFO_FLAGS: mesh path flags, enumerated in
  *      &enum nl80211_mpath_flags;
- * @NL80211_ATTR_MPATH_DISCOVERY_TIMEOUT: total path discovery timeout, in msec
- * @NL80211_ATTR_MPATH_DISCOVERY_RETRIES: mesh path discovery retries
+ * @NL80211_MPATH_INFO_DISCOVERY_TIMEOUT: total path discovery timeout, in msec
+ * @NL80211_MPATH_INFO_DISCOVERY_RETRIES: mesh path discovery retries
+ * @NL80211_MPATH_INFO_MAX: highest mesh path information attribute number
+ *      currently defind
+ * @__NL80211_MPATH_INFO_AFTER_LAST: internal use
  */
 enum nl80211_mpath_info {
         __NL80211_MPATH_INFO_INVALID,
@@ -1127,6 +1223,8 @@ enum nl80211_mpath_info {
  * @NL80211_BAND_ATTR_HT_CAPA: HT capabilities, as in the HT information IE
  * @NL80211_BAND_ATTR_HT_AMPDU_FACTOR: A-MPDU factor, as in 11n
  * @NL80211_BAND_ATTR_HT_AMPDU_DENSITY: A-MPDU density, as in 11n
+ * @NL80211_BAND_ATTR_MAX: highest band attribute currently defined
+ * @__NL80211_BAND_ATTR_AFTER_LAST: internal use
  */
 enum nl80211_band_attr {
         __NL80211_BAND_ATTR_INVALID,
@@ -1147,6 +1245,7 @@ enum nl80211_band_attr {
 
 /**
  * enum nl80211_frequency_attr - frequency attributes
+ * @__NL80211_FREQUENCY_ATTR_INVALID: attribute number 0 is reserved
  * @NL80211_FREQUENCY_ATTR_FREQ: Frequency in MHz
  * @NL80211_FREQUENCY_ATTR_DISABLED: Channel is disabled in current
  *      regulatory domain.
@@ -1158,6 +1257,9 @@ enum nl80211_band_attr {
  *      on this channel in current regulatory domain.
  * @NL80211_FREQUENCY_ATTR_MAX_TX_POWER: Maximum transmission power in mBm
  *      (100 * dBm).
+ * @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number
+ *      currently defined
+ * @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use
  */
 enum nl80211_frequency_attr {
         __NL80211_FREQUENCY_ATTR_INVALID,
@@ -1177,9 +1279,13 @@ enum nl80211_frequency_attr {
 
 /**
  * enum nl80211_bitrate_attr - bitrate attributes
+ * @__NL80211_BITRATE_ATTR_INVALID: attribute number 0 is reserved
  * @NL80211_BITRATE_ATTR_RATE: Bitrate in units of 100 kbps
  * @NL80211_BITRATE_ATTR_2GHZ_SHORTPREAMBLE: Short preamble supported
  *      in 2.4 GHz band.
+ * @NL80211_BITRATE_ATTR_MAX: highest bitrate attribute number
+ *      currently defined
+ * @__NL80211_BITRATE_ATTR_AFTER_LAST: internal use
  */
 enum nl80211_bitrate_attr {
         __NL80211_BITRATE_ATTR_INVALID,
@@ -1235,6 +1341,7 @@ enum nl80211_reg_type {
 
 /**
  * enum nl80211_reg_rule_attr - regulatory rule attributes
+ * @__NL80211_REG_RULE_ATTR_INVALID: attribute number 0 is reserved
  * @NL80211_ATTR_REG_RULE_FLAGS: a set of flags which specify additional
  *      considerations for a given frequency range. These are the
  *      &enum nl80211_reg_rule_flags.
@@ -1251,6 +1358,9 @@ enum nl80211_reg_type {
  *      If you don't have one then don't send this.
  * @NL80211_ATTR_POWER_RULE_MAX_EIRP: the maximum allowed EIRP for
  *      a given frequency range. The value is in mBm (100 * dBm).
+ * @NL80211_REG_RULE_ATTR_MAX: highest regulatory rule attribute number
+ *      currently defined
+ * @__NL80211_REG_RULE_ATTR_AFTER_LAST: internal use
  */
 enum nl80211_reg_rule_attr {
         __NL80211_REG_RULE_ATTR_INVALID,
@@ -1302,11 +1412,31 @@ enum nl80211_reg_rule_flags {
  * @__NL80211_SURVEY_INFO_INVALID: attribute number 0 is reserved
  * @NL80211_SURVEY_INFO_FREQUENCY: center frequency of channel
  * @NL80211_SURVEY_INFO_NOISE: noise level of channel (u8, dBm)
+ * @NL80211_SURVEY_INFO_IN_USE: channel is currently being used
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME: amount of time (in ms) that the radio
+ *      spent on this channel
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME_BUSY: amount of the time the primary
+ *      channel was sensed busy (either due to activity or energy detect)
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME_EXT_BUSY: amount of time the extension
+ *      channel was sensed busy
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME_RX: amount of time the radio spent
+ *      receiving data
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME_TX: amount of time the radio spent
+ *      transmitting data
+ * @NL80211_SURVEY_INFO_MAX: highest survey info attribute number
+ *      currently defined
+ * @__NL80211_SURVEY_INFO_AFTER_LAST: internal use
  */
 enum nl80211_survey_info {
         __NL80211_SURVEY_INFO_INVALID,
         NL80211_SURVEY_INFO_FREQUENCY,
         NL80211_SURVEY_INFO_NOISE,
+        NL80211_SURVEY_INFO_IN_USE,
+        NL80211_SURVEY_INFO_CHANNEL_TIME,
+        NL80211_SURVEY_INFO_CHANNEL_TIME_BUSY,
+        NL80211_SURVEY_INFO_CHANNEL_TIME_EXT_BUSY,
+        NL80211_SURVEY_INFO_CHANNEL_TIME_RX,
+        NL80211_SURVEY_INFO_CHANNEL_TIME_TX,
 
         /* keep last */
         __NL80211_SURVEY_INFO_AFTER_LAST,
@@ -1466,6 +1596,7 @@ enum nl80211_channel_type {
  * enum nl80211_bss - netlink attributes for a BSS
  *
  * @__NL80211_BSS_INVALID: invalid
+ * @NL80211_BSS_BSSID: BSSID of the BSS (6 octets)
  * @NL80211_BSS_FREQUENCY: frequency in MHz (u32)
  * @NL80211_BSS_TSF: TSF of the received probe response/beacon (u64)
  * @NL80211_BSS_BEACON_INTERVAL: beacon interval of the (I)BSS (u16)
@@ -1509,6 +1640,12 @@ enum nl80211_bss {
 
 /**
  * enum nl80211_bss_status - BSS "status"
+ * @NL80211_BSS_STATUS_AUTHENTICATED: Authenticated with this BSS.
+ * @NL80211_BSS_STATUS_ASSOCIATED: Associated with this BSS.
+ * @NL80211_BSS_STATUS_IBSS_JOINED: Joined to this IBSS.
+ *
+ * The BSS status is a BSS attribute in scan dumps, which
+ * indicates the status the interface has wrt. this BSS.
  */
 enum nl80211_bss_status {
         NL80211_BSS_STATUS_AUTHENTICATED,
@@ -1546,11 +1683,14 @@ enum nl80211_auth_type {
  * @NL80211_KEYTYPE_GROUP: Group (broadcast/multicast) key
  * @NL80211_KEYTYPE_PAIRWISE: Pairwise (unicast/individual) key
  * @NL80211_KEYTYPE_PEERKEY: PeerKey (DLS)
+ * @NUM_NL80211_KEYTYPES: number of defined key types
  */
 enum nl80211_key_type {
         NL80211_KEYTYPE_GROUP,
         NL80211_KEYTYPE_PAIRWISE,
         NL80211_KEYTYPE_PEERKEY,
+
+        NUM_NL80211_KEYTYPES
 };
 
 /**
@@ -1581,6 +1721,9 @@ enum nl80211_wpa_versions {
  *      CCMP keys, each six bytes in little endian
  * @NL80211_KEY_DEFAULT: flag indicating default key
  * @NL80211_KEY_DEFAULT_MGMT: flag indicating default management key
+ * @NL80211_KEY_TYPE: the key type from enum nl80211_key_type, if not
+ *      specified the default depends on whether a MAC address was
+ *      given with the command using the key or not (u32)
  * @__NL80211_KEY_AFTER_LAST: internal
  * @NL80211_KEY_MAX: highest key attribute
  */
@@ -1592,6 +1735,7 @@ enum nl80211_key_attributes {
         NL80211_KEY_SEQ,
         NL80211_KEY_DEFAULT,
         NL80211_KEY_DEFAULT_MGMT,
+        NL80211_KEY_TYPE,
 
         /* keep last */
         __NL80211_KEY_AFTER_LAST,
@@ -1619,8 +1763,8 @@ enum nl80211_tx_rate_attributes {
 
 /**
  * enum nl80211_band - Frequency band
- * @NL80211_BAND_2GHZ - 2.4 GHz ISM band
- * @NL80211_BAND_5GHZ - around 5 GHz band (4.9 - 5.7 GHz)
+ * @NL80211_BAND_2GHZ: 2.4 GHz ISM band
+ * @NL80211_BAND_5GHZ: around 5 GHz band (4.9 - 5.7 GHz)
  */
 enum nl80211_band {
         NL80211_BAND_2GHZ,
@@ -1658,9 +1802,9 @@ enum nl80211_attr_cqm {
 
 /**
  * enum nl80211_cqm_rssi_threshold_event - RSSI threshold event
- * @NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW - The RSSI level is lower than the
+ * @NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW: The RSSI level is lower than the
  *      configured threshold
- * @NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH - The RSSI is higher than the
+ * @NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH: The RSSI is higher than the
  *      configured threshold
  */
 enum nl80211_cqm_rssi_threshold_event {