1 files changed, 86 insertions, 83 deletions

diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h
index 93535f093216..cf2abeca92a0 100644
--- a/include/linux/ethtool.h
+++ b/include/linux/ethtool.h
@@ -15,24 +15,24 @@
 
 /* This should work for both 32 and 64 bit userland. */
 struct ethtool_cmd {
-        u32     cmd;
-        u32     supported;      /* Features this interface supports */
-        u32     advertising;    /* Features this interface advertises */
-        u16     speed;          /* The forced speed, 10Mb, 100Mb, gigabit */
-        u8      duplex;         /* Duplex, half or full */
-        u8      port;           /* Which connector port */
-        u8      phy_address;
-        u8      transceiver;    /* Which transceiver to use */
-        u8      autoneg;        /* Enable or disable autonegotiation */
-        u32     maxtxpkt;       /* Tx pkts before generating tx int */
-        u32     maxrxpkt;       /* Rx pkts before generating rx int */
-        u32     reserved[4];
+        __u32   cmd;
+        __u32   supported;      /* Features this interface supports */
+        __u32   advertising;    /* Features this interface advertises */
+        __u16   speed;          /* The forced speed, 10Mb, 100Mb, gigabit */
+        __u8    duplex;         /* Duplex, half or full */
+        __u8    port;           /* Which connector port */
+        __u8    phy_address;
+        __u8    transceiver;    /* Which transceiver to use */
+        __u8    autoneg;        /* Enable or disable autonegotiation */
+        __u32   maxtxpkt;       /* Tx pkts before generating tx int */
+        __u32   maxrxpkt;       /* Rx pkts before generating rx int */
+        __u32   reserved[4];
 };
 
 #define ETHTOOL_BUSINFO_LEN     32
 /* these strings are set to whatever the driver author decides... */
 struct ethtool_drvinfo {
-        u32     cmd;
+        __u32   cmd;
         char    driver[32];     /* driver short name, "tulip", "eepro100" */
         char    version[32];    /* driver version string */
         char    fw_version[32]; /* firmware version string, if applicable */
@@ -40,53 +40,53 @@ struct ethtool_drvinfo {
                                 /* For PCI devices, use pci_name(pci_dev). */
         char    reserved1[32];
         char    reserved2[16];
-        u32     n_stats;        /* number of u64's from ETHTOOL_GSTATS */
-        u32     testinfo_len;
-        u32     eedump_len;     /* Size of data from ETHTOOL_GEEPROM (bytes) */
-        u32     regdump_len;    /* Size of data from ETHTOOL_GREGS (bytes) */
+        __u32   n_stats;        /* number of u64's from ETHTOOL_GSTATS */
+        __u32   testinfo_len;
+        __u32   eedump_len;     /* Size of data from ETHTOOL_GEEPROM (bytes) */
+        __u32   regdump_len;    /* Size of data from ETHTOOL_GREGS (bytes) */
 };
 
 #define SOPASS_MAX      6
 /* wake-on-lan settings */
 struct ethtool_wolinfo {
-        u32     cmd;
-        u32     supported;
-        u32     wolopts;
-        u8      sopass[SOPASS_MAX]; /* SecureOn(tm) password */
+        __u32   cmd;
+        __u32   supported;
+        __u32   wolopts;
+        __u8    sopass[SOPASS_MAX]; /* SecureOn(tm) password */
 };
 
 /* for passing single values */
 struct ethtool_value {
-        u32     cmd;
-        u32     data;
+        __u32   cmd;
+        __u32   data;
 };
 
 /* for passing big chunks of data */
 struct ethtool_regs {
-        u32     cmd;
-        u32     version; /* driver-specific, indicates different chips/revs */
-        u32     len; /* bytes */
-        u8      data[0];
+        __u32   cmd;
+        __u32   version; /* driver-specific, indicates different chips/revs */
+        __u32   len; /* bytes */
+        __u8    data[0];
 };
 
 /* for passing EEPROM chunks */
 struct ethtool_eeprom {
-        u32     cmd;
-        u32     magic;
-        u32     offset; /* in bytes */
-        u32     len; /* in bytes */
-        u8      data[0];
+        __u32   cmd;
+        __u32   magic;
+        __u32   offset; /* in bytes */
+        __u32   len; /* in bytes */
+        __u8    data[0];
 };
 
 /* for configuring coalescing parameters of chip */
 struct ethtool_coalesce {
-        u32     cmd;    /* ETHTOOL_{G,S}COALESCE */
+        __u32   cmd;    /* ETHTOOL_{G,S}COALESCE */
 
         /* How many usecs to delay an RX interrupt after
          * a packet arrives.  If 0, only rx_max_coalesced_frames
          * is used.
          */
-        u32     rx_coalesce_usecs;
+        __u32   rx_coalesce_usecs;
 
         /* How many packets to delay an RX interrupt after
          * a packet arrives.  If 0, only rx_coalesce_usecs is
@@ -94,21 +94,21 @@ struct ethtool_coalesce {
          * to zero as this would cause RX interrupts to never be
          * generated.
          */
-        u32     rx_max_coalesced_frames;
+        __u32   rx_max_coalesced_frames;
 
         /* Same as above two parameters, except that these values
          * apply while an IRQ is being serviced by the host.  Not
          * all cards support this feature and the values are ignored
          * in that case.
          */
-        u32     rx_coalesce_usecs_irq;
-        u32     rx_max_coalesced_frames_irq;
+        __u32   rx_coalesce_usecs_irq;
+        __u32   rx_max_coalesced_frames_irq;
 
         /* How many usecs to delay a TX interrupt after
          * a packet is sent.  If 0, only tx_max_coalesced_frames
          * is used.
          */
-        u32     tx_coalesce_usecs;
+        __u32   tx_coalesce_usecs;
 
         /* How many packets to delay a TX interrupt after
          * a packet is sent.  If 0, only tx_coalesce_usecs is
@@ -116,22 +116,22 @@ struct ethtool_coalesce {
          * to zero as this would cause TX interrupts to never be
          * generated.
          */
-        u32     tx_max_coalesced_frames;
+        __u32   tx_max_coalesced_frames;
 
         /* Same as above two parameters, except that these values
          * apply while an IRQ is being serviced by the host.  Not
          * all cards support this feature and the values are ignored
          * in that case.
          */
-        u32     tx_coalesce_usecs_irq;
-        u32     tx_max_coalesced_frames_irq;
+        __u32   tx_coalesce_usecs_irq;
+        __u32   tx_max_coalesced_frames_irq;
 
         /* How many usecs to delay in-memory statistics
          * block updates.  Some drivers do not have an in-memory
          * statistic block, and in such cases this value is ignored.
          * This value must not be zero.
          */
-        u32     stats_block_coalesce_usecs;
+        __u32   stats_block_coalesce_usecs;
 
         /* Adaptive RX/TX coalescing is an algorithm implemented by
          * some drivers to improve latency under low packet rates and
@@ -140,18 +140,18 @@ struct ethtool_coalesce {
          * not implemented by the driver causes these values to be
          * silently ignored.
          */
-        u32     use_adaptive_rx_coalesce;
-        u32     use_adaptive_tx_coalesce;
+        __u32   use_adaptive_rx_coalesce;
+        __u32   use_adaptive_tx_coalesce;
 
         /* When the packet rate (measured in packets per second)
          * is below pkt_rate_low, the {rx,tx}_*_low parameters are
          * used.
          */
-        u32     pkt_rate_low;
-        u32     rx_coalesce_usecs_low;
-        u32     rx_max_coalesced_frames_low;
-        u32     tx_coalesce_usecs_low;
-        u32     tx_max_coalesced_frames_low;
+        __u32   pkt_rate_low;
+        __u32   rx_coalesce_usecs_low;
+        __u32   rx_max_coalesced_frames_low;
+        __u32   tx_coalesce_usecs_low;
+        __u32   tx_max_coalesced_frames_low;
 
         /* When the packet rate is below pkt_rate_high but above
          * pkt_rate_low (both measured in packets per second) the
@@ -162,43 +162,43 @@ struct ethtool_coalesce {
          * is above pkt_rate_high, the {rx,tx}_*_high parameters are
          * used.
          */
-        u32     pkt_rate_high;
-        u32     rx_coalesce_usecs_high;
-        u32     rx_max_coalesced_frames_high;
-        u32     tx_coalesce_usecs_high;
-        u32     tx_max_coalesced_frames_high;
+        __u32   pkt_rate_high;
+        __u32   rx_coalesce_usecs_high;
+        __u32   rx_max_coalesced_frames_high;
+        __u32   tx_coalesce_usecs_high;
+        __u32   tx_max_coalesced_frames_high;
 
         /* How often to do adaptive coalescing packet rate sampling,
          * measured in seconds.  Must not be zero.
          */
-        u32     rate_sample_interval;
+        __u32   rate_sample_interval;
 };
 
 /* for configuring RX/TX ring parameters */
 struct ethtool_ringparam {
-        u32     cmd;    /* ETHTOOL_{G,S}RINGPARAM */
+        __u32   cmd;    /* ETHTOOL_{G,S}RINGPARAM */
 
         /* Read only attributes.  These indicate the maximum number
          * of pending RX/TX ring entries the driver will allow the
          * user to set.
          */
-        u32     rx_max_pending;
-        u32     rx_mini_max_pending;
-        u32     rx_jumbo_max_pending;
-        u32     tx_max_pending;
+        __u32   rx_max_pending;
+        __u32   rx_mini_max_pending;
+        __u32   rx_jumbo_max_pending;
+        __u32   tx_max_pending;
 
         /* Values changeable by the user.  The valid values are
          * in the range 1 to the "*_max_pending" counterpart above.
          */
-        u32     rx_pending;
-        u32     rx_mini_pending;
-        u32     rx_jumbo_pending;
-        u32     tx_pending;
+        __u32   rx_pending;
+        __u32   rx_mini_pending;
+        __u32   rx_jumbo_pending;
+        __u32   tx_pending;
 };
 
 /* for configuring link flow control parameters */
 struct ethtool_pauseparam {
-        u32     cmd;    /* ETHTOOL_{G,S}PAUSEPARAM */
+        __u32   cmd;    /* ETHTOOL_{G,S}PAUSEPARAM */
 
         /* If the link is being auto-negotiated (via ethtool_cmd.autoneg
          * being true) the user may set 'autonet' here non-zero to have the
@@ -210,9 +210,9 @@ struct ethtool_pauseparam {
          * then {rx,tx}_pause force the driver to use/not-use pause
          * flow control.
          */
-        u32     autoneg;
-        u32     rx_pause;
-        u32     tx_pause;
+        __u32   autoneg;
+        __u32   rx_pause;
+        __u32   tx_pause;
 };
 
 #define ETH_GSTRING_LEN         32
@@ -223,10 +223,10 @@ enum ethtool_stringset {
 
 /* for passing string sets for data tagging */
 struct ethtool_gstrings {
-        u32     cmd;            /* ETHTOOL_GSTRINGS */
-        u32     string_set;     /* string set id e.c. ETH_SS_TEST, etc*/
-        u32     len;            /* number of strings in the string set */
-        u8      data[0];
+        __u32   cmd;            /* ETHTOOL_GSTRINGS */
+        __u32   string_set;     /* string set id e.c. ETH_SS_TEST, etc*/
+        __u32   len;            /* number of strings in the string set */
+        __u8    data[0];
 };
 
 enum ethtool_test_flags {
@@ -236,26 +236,28 @@ enum ethtool_test_flags {
 
 /* for requesting NIC test and getting results*/
 struct ethtool_test {
-        u32     cmd;            /* ETHTOOL_TEST */
-        u32     flags;          /* ETH_TEST_FL_xxx */
-        u32     reserved;
-        u32     len;            /* result length, in number of u64 elements */
-        u64     data[0];
+        __u32   cmd;            /* ETHTOOL_TEST */
+        __u32   flags;          /* ETH_TEST_FL_xxx */
+        __u32   reserved;
+        __u32   len;            /* result length, in number of u64 elements */
+        __u64   data[0];
 };
 
 /* for dumping NIC-specific statistics */
 struct ethtool_stats {
-        u32     cmd;            /* ETHTOOL_GSTATS */
-        u32     n_stats;        /* number of u64's being returned */
-        u64     data[0];
+        __u32   cmd;            /* ETHTOOL_GSTATS */
+        __u32   n_stats;        /* number of u64's being returned */
+        __u64   data[0];
 };
 
 struct ethtool_perm_addr {
-        u32     cmd;            /* ETHTOOL_GPERMADDR */
-        u32     size;
-        u8      data[0];
+        __u32   cmd;            /* ETHTOOL_GPERMADDR */
+        __u32   size;
+        __u8    data[0];
 };
 
+#ifdef __KERNEL__
+
 struct net_device;
 
 /* Some generic methods drivers may use in their ethtool_ops */
@@ -371,6 +373,7 @@ struct ethtool_ops {
         u32     (*get_ufo)(struct net_device *);
         int     (*set_ufo)(struct net_device *, u32);
 };
+#endif /* __KERNEL__ */
 
 /* CMDs currently supported */
 #define ETHTOOL_GSET            0x00000001 /* Get settings. */