1 files changed, 122 insertions, 0 deletions

diff --git a/include/asm-arm/arch-at91/board.h b/include/asm-arm/arch-at91/board.h
new file mode 100644
index 000000000000..7b9903c2c447
--- /dev/null
+++ b/include/asm-arm/arch-at91/board.h
@@ -0,0 +1,122 @@
+/*
+ * include/asm-arm/arch-at91/board.h
+ *
+ *  Copyright (C) 2005 HP Labs
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+/*
+ * These are data structures found in platform_device.dev.platform_data,
+ * and describing board-specific data needed by drivers.  For example,
+ * which pin is used for a given GPIO role.
+ *
+ * In 2.6, drivers should strongly avoid board-specific knowledge so
+ * that supporting new boards normally won't require driver patches.
+ * Most board-specific knowledge should be in arch/.../board-*.c files.
+ */
+
+#ifndef __ASM_ARCH_BOARD_H
+#define __ASM_ARCH_BOARD_H
+
+#include <linux/mtd/partitions.h>
+#include <linux/device.h>
+#include <linux/spi/spi.h>
+
+ /* USB Device */
+struct at91_udc_data {
+        u8      vbus_pin;               /* high == host powering us */
+        u8      pullup_pin;             /* high == D+ pulled up */
+};
+extern void __init at91_add_device_udc(struct at91_udc_data *data);
+
+ /* Compact Flash */
+struct at91_cf_data {
+        u8      irq_pin;                /* I/O IRQ */
+        u8      det_pin;                /* Card detect */
+        u8      vcc_pin;                /* power switching */
+        u8      rst_pin;                /* card reset */
+        u8      chipselect;             /* EBI Chip Select number */
+};
+extern void __init at91_add_device_cf(struct at91_cf_data *data);
+
+ /* MMC / SD */
+struct at91_mmc_data {
+        u8              det_pin;        /* card detect IRQ */
+        unsigned        slot_b:1;       /* uses Slot B */
+        unsigned        wire4:1;        /* (SD) supports DAT0..DAT3 */
+        u8              wp_pin;         /* (SD) writeprotect detect */
+        u8              vcc_pin;        /* power switching (high == on) */
+};
+extern void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data);
+
+ /* Ethernet */
+struct at91_eth_data {
+        u8              phy_irq_pin;    /* PHY IRQ */
+        u8              is_rmii;        /* using RMII interface? */
+};
+extern void __init at91_add_device_eth(struct at91_eth_data *data);
+
+#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263)
+#define eth_platform_data       at91_eth_data
+#endif
+
+ /* USB Host */
+struct at91_usbh_data {
+        u8              ports;          /* number of ports on root hub */
+        u8              vbus_pin[];     /* port power-control pin */
+};
+extern void __init at91_add_device_usbh(struct at91_usbh_data *data);
+
+ /* NAND / SmartMedia */
+struct at91_nand_data {
+        u8              enable_pin;     /* chip enable */
+        u8              det_pin;        /* card detect */
+        u8              rdy_pin;        /* ready/busy */
+        u8              ale;            /* address line number connected to ALE */
+        u8              cle;            /* address line number connected to CLE */
+        u8              bus_width_16;   /* buswidth is 16 bit */
+        struct mtd_partition* (*partition_info)(int, int*);
+};
+extern void __init at91_add_device_nand(struct at91_nand_data *data);
+
+ /* I2C*/
+extern void __init at91_add_device_i2c(void);
+
+ /* SPI */
+extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices);
+
+ /* Serial */
+struct at91_uart_config {
+        unsigned short  console_tty;    /* tty number of serial console */
+        unsigned short  nr_tty;         /* number of serial tty's */
+        short           tty_map[];      /* map UART to tty number */
+};
+extern struct platform_device *atmel_default_console_device;
+extern void __init at91_init_serial(struct at91_uart_config *config);
+
+struct atmel_uart_data {
+        short           use_dma_tx;     /* use transmit DMA? */
+        short           use_dma_rx;     /* use receive DMA? */
+        void __iomem    *regs;          /* virtual base address, if any */
+};
+extern void __init at91_add_device_serial(void);
+
+ /* LEDs */
+extern u8 at91_leds_cpu;
+extern u8 at91_leds_timer;
+extern void __init at91_init_leds(u8 cpu_led, u8 timer_led);
+
+#endif