3 files changed, 7 insertions, 7 deletions

diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 737335ff2b21..e8fe7f169e25 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -128,7 +128,7 @@ config I2C_PIIX4
             ATI SB600
             ATI SB700
             ATI SB800
-            AMD SB900
+            AMD Hudson-2
             Serverworks OSB4
             Serverworks CSB5
             Serverworks CSB6
diff --git a/drivers/i2c/busses/i2c-piix4.c b/drivers/i2c/busses/i2c-piix4.c
index d26a972aacaa..1e245e9cad31 100644
--- a/drivers/i2c/busses/i2c-piix4.c
+++ b/drivers/i2c/busses/i2c-piix4.c
@@ -22,7 +22,7 @@
         Intel PIIX4, 440MX
         Serverworks OSB4, CSB5, CSB6, HT-1000, HT-1100
         ATI IXP200, IXP300, IXP400, SB600, SB700, SB800
-        AMD SB900
+        AMD Hudson-2
         SMSC Victory66
 
    Note: we assume there can only be one device, with one SMBus interface.
@@ -233,9 +233,9 @@ static int __devinit piix4_setup_sb800(struct pci_dev *PIIX4_dev,
         unsigned short smba_idx = 0xcd6;
         u8 smba_en_lo, smba_en_hi, i2ccfg, i2ccfg_offset = 0x10, smb_en = 0x2c;
 
-        /* SB800 SMBus does not support forcing address */
+        /* SB800 and later SMBus does not support forcing address */
         if (force || force_addr) {
-                dev_err(&PIIX4_dev->dev, "SB800 SMBus does not support "
+                dev_err(&PIIX4_dev->dev, "SMBus does not support "
                         "forcing address!\n");
                 return -EINVAL;
         }
@@ -480,7 +480,7 @@ static struct pci_device_id piix4_ids[] = {
         { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP300_SMBUS) },
         { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP400_SMBUS) },
         { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_SBX00_SMBUS) },
-        { PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_SB900_SMBUS) },
+        { PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_HUDSON2_SMBUS) },
         { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS,
                      PCI_DEVICE_ID_SERVERWORKS_OSB4) },
         { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS,
diff --git a/drivers/net/sfc/sfe4001.c b/drivers/net/sfc/sfe4001.c
index cee00ad49b57..49eb91b5f50c 100644
--- a/drivers/net/sfc/sfe4001.c
+++ b/drivers/net/sfc/sfe4001.c
@@ -188,7 +188,7 @@ static int sfn4111t_reset(struct efx_nic *efx)
         efx_oword_t reg;
 
         /* GPIO 3 and the GPIO register are shared with I2C, so block that */
-        mutex_lock(&efx->i2c_adap.bus_lock);
+        i2c_lock_adapter(&efx->i2c_adap);
 
         /* Pull RST_N (GPIO 2) low then let it up again, setting the
          * FLASH_CFG_1 strap (GPIO 3) appropriately.  Only change the
@@ -204,7 +204,7 @@ static int sfn4111t_reset(struct efx_nic *efx)
         falcon_write(efx, &reg, GPIO_CTL_REG_KER);
         msleep(1);
 
-        mutex_unlock(&efx->i2c_adap.bus_lock);
+        i2c_unlock_adapter(&efx->i2c_adap);
 
         ssleep(1);
         return 0;