67 files changed, 19980 insertions, 1229 deletions

diff --git a/drivers/Kconfig b/drivers/Kconfig
index 8b11cebe65df..263e86ddc1a4 100644
--- a/drivers/Kconfig
+++ b/drivers/Kconfig
@@ -18,6 +18,8 @@ source "drivers/ide/Kconfig"
 
 source "drivers/scsi/Kconfig"
 
+source "drivers/ata/Kconfig"
+
 source "drivers/cdrom/Kconfig"
 
 source "drivers/md/Kconfig"
diff --git a/drivers/Makefile b/drivers/Makefile
index fc2d744a4e4a..4ac14dab3079 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -34,6 +34,7 @@ obj-$(CONFIG_PPC_PMAC)		+= macintosh/
 obj-$(CONFIG_IDE)               += ide/
 obj-$(CONFIG_FC4)               += fc4/
 obj-$(CONFIG_SCSI)              += scsi/
+obj-$(CONFIG_ATA)               += ata/
 obj-$(CONFIG_FUSION)            += message/
 obj-$(CONFIG_IEEE1394)          += ieee1394/
 obj-y                           += cdrom/
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
new file mode 100644
index 000000000000..cbf0deb25033
--- /dev/null
+++ b/drivers/ata/Kconfig
@@ -0,0 +1,493 @@
+#
+# SATA/PATA driver configuration
+#
+
+menu "Serial ATA (prod) and Parallel ATA (experimental) drivers"
+
+config ATA
+        tristate "ATA device support"
+        select SCSI
+        ---help---
+          If you want to use a ATA hard disk, ATA tape drive, ATA CD-ROM or
+          any other ATA device under Linux, say Y and make sure that you know
+          the name of your ATA host adapter (the card inside your computer
+          that "speaks" the ATA protocol, also called ATA controller),
+          because you will be asked for it.
+
+if ATA
+
+config SATA_AHCI
+        tristate "AHCI SATA support"
+        depends on PCI
+        help
+          This option enables support for AHCI Serial ATA.
+
+          If unsure, say N.
+
+config SATA_SVW
+        tristate "ServerWorks Frodo / Apple K2 SATA support"
+        depends on PCI
+        help
+          This option enables support for Broadcom/Serverworks/Apple K2
+          SATA support.
+
+          If unsure, say N.
+
+config ATA_PIIX
+        tristate "Intel PIIX/ICH SATA support"
+        depends on PCI
+        help
+          This option enables support for ICH5/6/7/8 Serial ATA.
+          If PATA support was enabled previously, this enables
+          support for select Intel PIIX/ICH PATA host controllers.
+
+          If unsure, say N.
+
+config SATA_MV
+        tristate "Marvell SATA support (HIGHLY EXPERIMENTAL)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables support for the Marvell Serial ATA family.
+          Currently supports 88SX[56]0[48][01] chips.
+
+          If unsure, say N.
+
+config SATA_NV
+        tristate "NVIDIA SATA support"
+        depends on PCI
+        help
+          This option enables support for NVIDIA Serial ATA.
+
+          If unsure, say N.
+
+config PDC_ADMA
+        tristate "Pacific Digital ADMA support"
+        depends on PCI
+        help
+          This option enables support for Pacific Digital ADMA controllers
+
+          If unsure, say N.
+
+config SATA_QSTOR
+        tristate "Pacific Digital SATA QStor support"
+        depends on PCI
+        help
+          This option enables support for Pacific Digital Serial ATA QStor.
+
+          If unsure, say N.
+
+config SATA_PROMISE
+        tristate "Promise SATA TX2/TX4 support"
+        depends on PCI
+        help
+          This option enables support for Promise Serial ATA TX2/TX4.
+
+          If unsure, say N.
+
+config SATA_SX4
+        tristate "Promise SATA SX4 support"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables support for Promise Serial ATA SX4.
+
+          If unsure, say N.
+
+config SATA_SIL
+        tristate "Silicon Image SATA support"
+        depends on PCI
+        help
+          This option enables support for Silicon Image Serial ATA.
+
+          If unsure, say N.
+
+config SATA_SIL24
+        tristate "Silicon Image 3124/3132 SATA support"
+        depends on PCI
+        help
+          This option enables support for Silicon Image 3124/3132 Serial ATA.
+
+          If unsure, say N.
+
+config SATA_SIS
+        tristate "SiS 964/180 SATA support"
+        depends on PCI
+        help
+          This option enables support for SiS Serial ATA 964/180.
+
+          If unsure, say N.
+
+config SATA_ULI
+        tristate "ULi Electronics SATA support"
+        depends on PCI
+        help
+          This option enables support for ULi Electronics SATA.
+
+          If unsure, say N.
+
+config SATA_VIA
+        tristate "VIA SATA support"
+        depends on PCI
+        help
+          This option enables support for VIA Serial ATA.
+
+          If unsure, say N.
+
+config SATA_VITESSE
+        tristate "VITESSE VSC-7174 / INTEL 31244 SATA support"
+        depends on PCI
+        help
+          This option enables support for Vitesse VSC7174 and Intel 31244 Serial ATA.
+
+          If unsure, say N.
+
+config SATA_INTEL_COMBINED
+        bool
+        depends on IDE=y && !BLK_DEV_IDE_SATA && (SATA_AHCI || ATA_PIIX)
+        default y
+
+config PATA_ALI
+        tristate "ALi PATA support (Experimental)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables support for the ALi ATA interfaces
+          found on the many ALi chipsets.
+
+          If unsure, say N.
+
+config PATA_AMD
+        tristate "AMD/NVidia PATA support (Experimental)"
+        depends on PCI
+        help
+          This option enables support for the AMD and NVidia PATA
+          interfaces found on the chipsets for Athlon/Athlon64.
+
+          If unsure, say N.
+
+config PATA_ARTOP
+        tristate "ARTOP 6210/6260 PATA support (Experimental)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables support for ARTOP PATA controllers.
+
+          If unsure, say N.
+
+config PATA_ATIIXP
+        tristate "ATI PATA support (Experimental)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables support for the ATI ATA interfaces
+          found on the many ATI chipsets.
+
+          If unsure, say N.
+
+config PATA_CMD64X
+        tristate "CMD64x PATA support (Very Experimental)"
+        depends on PCI&& EXPERIMENTAL
+        help
+          This option enables support for the CMD64x series chips
+          except for the CMD640.
+
+          If unsure, say N.
+
+config PATA_CS5520
+        tristate "CS5510/5520 PATA support"
+        depends on PCI
+        help
+          This option enables support for the Cyrix 5510/5520
+          companion chip used with the MediaGX/Geode processor family.
+
+          If unsure, say N.
+
+config PATA_CS5530
+        tristate "CS5530 PATA support (Experimental)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables support for the Cyrix/NatSemi/AMD CS5530
+          companion chip used with the MediaGX/Geode processor family.
+
+          If unsure, say N.
+
+config PATA_CS5535
+        tristate "CS5535 PATA support (Experimental)"
+        depends on PCI && X86 && !X86_64 && EXPERIMENTAL
+        help
+          This option enables support for the NatSemi/AMD CS5535
+          companion chip used with the Geode processor family.
+
+          If unsure, say N.
+
+config PATA_CYPRESS
+        tristate "Cypress CY82C693 PATA support (Very Experimental)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables support for the Cypress/Contaq CY82C693
+          chipset found in some Alpha systems
+
+          If unsure, say N.
+
+config PATA_EFAR
+        tristate "EFAR SLC90E66 support"
+        depends on PCI
+        help
+          This option enables support for the EFAR SLC90E66
+          IDE controller found on some older machines.
+
+          If unsure, say N.
+
+config ATA_GENERIC
+        tristate "Generic ATA support"
+        depends on PCI
+        help
+          This option enables support for generic BIOS configured
+          ATA controllers via the new ATA layer
+
+          If unsure, say N.
+
+config PATA_HPT366
+        tristate "HPT 366/368 PATA support (Very Experimental)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables support for the HPT 366 and 368
+          PATA controllers via the new ATA layer.
+
+          If unsure, say N.
+
+config PATA_HPT37X
+        tristate "HPT 370/370A/371/372/374/302 PATA support (Very Experimental)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables support for the majority of the later HPT
+          PATA controllers via the new ATA layer.
+
+          If unsure, say N.
+
+config PATA_HPT3X2N
+        tristate "HPT 372N/302N PATA support (Very Experimental)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables support for the N variant HPT PATA
+          controllers via the new ATA layer
+
+          If unsure, say N.
+
+config PATA_HPT3X3
+        tristate "HPT 343/363 PATA support (Experimental)"
+        depends on PCI
+        help
+          This option enables support for the HPT 343/363
+          PATA controllers via the new ATA layer
+
+          If unsure, say N.
+
+config PATA_ISAPNP
+        tristate "ISA Plug and Play PATA support (Very Experimental)"
+        depends on EXPERIMENTAL && ISAPNP
+        help
+          This option enables support for ISA plug & play ATA
+          controllers such as those found on old soundcards.
+
+          If unsure, say N.
+
+config PATA_IT8172
+        tristate "IT8172 PATA support (Very Experimental)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables support for the ITE 8172 PATA controller
+          via the new ATA layer.
+
+          If unsure, say N.
+
+config PATA_IT821X
+        tristate "IT821x PATA support (Experimental)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables support for the ITE 8211 and 8212
+          PATA controllers via the new ATA layer, including RAID
+          mode.
+
+          If unsure, say N.
+
+config PATA_JMICRON
+        tristate "JMicron PATA support"
+        depends on PCI
+        help
+          Enable support for the JMicron IDE controller, via the new
+          ATA layer.
+
+          If unsure, say N.
+
+config PATA_LEGACY
+        tristate "Legacy ISA PATA support (Experimental)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables support for ISA/VLB bus legacy PATA
+          ports and allows them to be accessed via the new ATA layer.
+
+          If unsure, say N.
+
+config PATA_TRIFLEX
+        tristate "Compaq Triflex PATA support"
+        depends on PCI
+        help
+          Enable support for the Compaq 'Triflex' IDE controller as found
+          on many Compaq Pentium-Pro systems, via the new ATA layer.
+
+          If unsure, say N.
+
+config PATA_MPIIX
+        tristate "Intel PATA MPIIX support"
+        depends on PCI
+        help
+          This option enables support for MPIIX PATA support.
+
+          If unsure, say N.
+
+config PATA_OLDPIIX
+        tristate "Intel PATA old PIIX support (Experimental)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables support for old(?) PIIX PATA support.
+
+          If unsure, say N.
+
+config PATA_NETCELL
+        tristate "NETCELL Revolution RAID support"
+        depends on PCI
+        help
+          This option enables support for the Netcell Revolution RAID
+          PATA controller.
+
+          If unsure, say N.
+
+config PATA_NS87410
+        tristate "Nat Semi NS87410 PATA support (Experimental)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables support for the National Semiconductor
+          NS87410 PCI-IDE controller.
+
+          If unsure, say N.
+
+config PATA_OPTI
+        tristate "OPTI621/6215 PATA support (Very Experimental)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables full PIO support for the early Opti ATA
+          controllers found on some old motherboards.
+
+          If unsure, say N.
+
+config PATA_OPTIDMA
+        tristate "OPTI FireStar PATA support (Veyr Experimental)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables DMA/PIO support for the later OPTi
+          controllers found on some old motherboards and in some
+          latops
+
+          If unsure, say N.
+
+config PATA_PCMCIA
+        tristate "PCMCIA PATA support"
+        depends on PCMCIA
+        help
+          This option enables support for PCMCIA ATA interfaces, including
+          compact flash card adapters via the new ATA layer.
+
+          If unsure, say N.
+
+config PATA_PDC_OLD
+        tristate "Older Promise PATA controller support (Very Experimental)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables support for the Promise 20246, 20262, 20263,
+          20265 and 20267 adapters.
+
+          If unsure, say N.
+
+config PATA_QDI
+        tristate "QDI VLB PATA support"
+        help
+          Support for QDI 6500 and 6580 PATA controllers on VESA local bus.
+
+config PATA_RADISYS
+        tristate "RADISYS 82600 PATA support (Very experimental)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables support for the RADISYS 82600
+          PATA controllers via the new ATA layer
+
+          If unsure, say N.
+
+config PATA_RZ1000
+        tristate "PC Tech RZ1000 PATA support"
+        depends on PCI
+        help
+          This option enables basic support for the PC Tech RZ1000/1
+          PATA controllers via the new ATA layer
+
+          If unsure, say N.
+
+config PATA_SC1200
+        tristate "SC1200 PATA support (Raving Lunatic)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables support for the NatSemi/AMD SC1200 SoC
+          companion chip used with the Geode processor family.
+
+          If unsure, say N.
+
+config PATA_SERVERWORKS
+        tristate "SERVERWORKS OSB4/CSB5/CSB6/HT1000 PATA support (Experimental)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables support for the Serverworks OSB4/CSB5/CSB6 and
+          HT1000 PATA controllers, via the new ATA layer.
+
+          If unsure, say N.
+
+config PATA_PDC2027X
+        tristate "Promise PATA 2027x support"
+        depends on PCI
+        help
+          This option enables support for Promise PATA pdc20268 to pdc20277 host adapters.
+
+          If unsure, say N.
+
+config PATA_SIL680
+        tristate "CMD / Silicon Image 680 PATA support"
+        depends on PCI
+        help
+          This option enables support for CMD / Silicon Image 680 PATA.
+
+          If unsure, say N.
+
+config PATA_SIS
+        tristate "SiS PATA support (Experimental)"
+        depends on PCI && EXPERIMENTAL
+        help
+          This option enables support for SiS PATA controllers
+
+          If unsure, say N.
+
+config PATA_VIA
+        tristate "VIA PATA support"
+        depends on PCI
+        help
+          This option enables support for the VIA PATA interfaces
+          found on the many VIA chipsets.
+
+          If unsure, say N.
+
+config PATA_WINBOND
+        tristate "Winbond SL82C105 PATA support"
+        depends on PCI
+        help
+          This option enables support for SL82C105 PATA devices found in the
+          Netwinder and some other systems
+
+          If unsure, say N.
+
+endif
+endmenu
+
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
new file mode 100644
index 000000000000..e42d14dbf037
--- /dev/null
+++ b/drivers/ata/Makefile
@@ -0,0 +1,63 @@
+
+obj-$(CONFIG_ATA)               += libata.o
+
+obj-$(CONFIG_SATA_AHCI)         += ahci.o
+obj-$(CONFIG_SATA_SVW)          += sata_svw.o
+obj-$(CONFIG_ATA_PIIX)          += ata_piix.o
+obj-$(CONFIG_SATA_PROMISE)      += sata_promise.o
+obj-$(CONFIG_SATA_QSTOR)        += sata_qstor.o
+obj-$(CONFIG_SATA_SIL)          += sata_sil.o
+obj-$(CONFIG_SATA_SIL24)        += sata_sil24.o
+obj-$(CONFIG_SATA_VIA)          += sata_via.o
+obj-$(CONFIG_SATA_VITESSE)      += sata_vsc.o
+obj-$(CONFIG_SATA_SIS)          += sata_sis.o
+obj-$(CONFIG_SATA_SX4)          += sata_sx4.o
+obj-$(CONFIG_SATA_NV)           += sata_nv.o
+obj-$(CONFIG_SATA_ULI)          += sata_uli.o
+obj-$(CONFIG_SATA_MV)           += sata_mv.o
+obj-$(CONFIG_PDC_ADMA)          += pdc_adma.o
+
+obj-$(CONFIG_PATA_ALI)          += pata_ali.o
+obj-$(CONFIG_PATA_AMD)          += pata_amd.o
+obj-$(CONFIG_PATA_ARTOP)        += pata_artop.o
+obj-$(CONFIG_PATA_ATIIXP)       += pata_atiixp.o
+obj-$(CONFIG_PATA_CMD64X)       += pata_cmd64x.o
+obj-$(CONFIG_PATA_CS5520)       += pata_cs5520.o
+obj-$(CONFIG_PATA_CS5530)       += pata_cs5530.o
+obj-$(CONFIG_PATA_CS5535)       += pata_cs5535.o
+obj-$(CONFIG_PATA_CYPRESS)      += pata_cypress.o
+obj-$(CONFIG_PATA_EFAR)         += pata_efar.o
+obj-$(CONFIG_PATA_HPT366)       += pata_hpt366.o
+obj-$(CONFIG_PATA_HPT37X)       += pata_hpt37x.o
+obj-$(CONFIG_PATA_HPT3X2N)      += pata_hpt3x2n.o
+obj-$(CONFIG_PATA_HPT3X3)       += pata_hpt3x3.o
+obj-$(CONFIG_PATA_ISAPNP)       += pata_isapnp.o
+obj-$(CONFIG_PATA_IT8172)       += pata_it8172.o
+obj-$(CONFIG_PATA_IT821X)       += pata_it821x.o
+obj-$(CONFIG_PATA_JMICRON)      += pata_jmicron.o
+obj-$(CONFIG_PATA_NETCELL)      += pata_netcell.o
+obj-$(CONFIG_PATA_NS87410)      += pata_ns87410.o
+obj-$(CONFIG_PATA_OPTI)         += pata_opti.o
+obj-$(CONFIG_PATA_OPTIDMA)      += pata_optidma.o
+obj-$(CONFIG_PATA_MPIIX)        += pata_mpiix.o
+obj-$(CONFIG_PATA_OLDPIIX)      += pata_oldpiix.o
+obj-$(CONFIG_PATA_PCMCIA)       += pata_pcmcia.o
+obj-$(CONFIG_PATA_PDC2027X)     += pata_pdc2027x.o
+obj-$(CONFIG_PATA_PDC_OLD)      += pata_pdc202xx_old.o
+obj-$(CONFIG_PATA_QDI)          += pata_qdi.o
+obj-$(CONFIG_PATA_RADISYS)      += pata_radisys.o
+obj-$(CONFIG_PATA_RZ1000)       += pata_rz1000.o
+obj-$(CONFIG_PATA_SC1200)       += pata_sc1200.o
+obj-$(CONFIG_PATA_SERVERWORKS)  += pata_serverworks.o
+obj-$(CONFIG_PATA_SIL680)       += pata_sil680.o
+obj-$(CONFIG_PATA_VIA)          += pata_via.o
+obj-$(CONFIG_PATA_WINBOND)      += pata_sl82c105.o
+obj-$(CONFIG_PATA_SIS)          += pata_sis.o
+obj-$(CONFIG_PATA_TRIFLEX)      += pata_triflex.o
+# Should be last but one libata driver
+obj-$(CONFIG_ATA_GENERIC)       += ata_generic.o
+# Should be last libata driver
+obj-$(CONFIG_PATA_LEGACY)       += pata_legacy.o
+
+libata-objs     := libata-core.o libata-scsi.o libata-sff.o libata-eh.o
+
diff --git a/drivers/scsi/ahci.c b/drivers/ata/ahci.c
index 904c25fb4ba4..1aabc81d82f1 100644
--- a/drivers/scsi/ahci.c
+++ b/drivers/ata/ahci.c
@@ -92,7 +92,9 @@ enum {
         HOST_AHCI_EN            = (1 << 31), /* AHCI enabled */
 
         /* HOST_CAP bits */
+        HOST_CAP_SSC            = (1 << 14), /* Slumber capable */
         HOST_CAP_CLO            = (1 << 24), /* Command List Override support */
+        HOST_CAP_SSS            = (1 << 27), /* Staggered Spin-up */
         HOST_CAP_NCQ            = (1 << 30), /* Native Command Queueing */
         HOST_CAP_64             = (1 << 31), /* PCI DAC (64-bit DMA) support */
 
@@ -155,6 +157,7 @@ enum {
         PORT_CMD_SPIN_UP        = (1 << 1), /* Spin up device */
         PORT_CMD_START          = (1 << 0), /* Enable port DMA engine */
 
+        PORT_CMD_ICC_MASK       = (0xf << 28), /* i/f ICC state mask */
         PORT_CMD_ICC_ACTIVE     = (0x1 << 28), /* Put i/f in active state */
         PORT_CMD_ICC_PARTIAL    = (0x2 << 28), /* Put i/f in partial state */
         PORT_CMD_ICC_SLUMBER    = (0x6 << 28), /* Put i/f in slumber state */
@@ -212,6 +215,10 @@ static void ahci_freeze(struct ata_port *ap);
 static void ahci_thaw(struct ata_port *ap);
 static void ahci_error_handler(struct ata_port *ap);
 static void ahci_post_internal_cmd(struct ata_queued_cmd *qc);
+static int ahci_port_suspend(struct ata_port *ap, pm_message_t mesg);
+static int ahci_port_resume(struct ata_port *ap);
+static int ahci_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg);
+static int ahci_pci_device_resume(struct pci_dev *pdev);
 static void ahci_remove_one (struct pci_dev *pdev);
 
 static struct scsi_host_template ahci_sht = {
@@ -231,6 +238,8 @@ static struct scsi_host_template ahci_sht = {
         .slave_configure        = ata_scsi_slave_config,
         .slave_destroy          = ata_scsi_slave_destroy,
         .bios_param             = ata_std_bios_param,
+        .suspend                = ata_scsi_device_suspend,
+        .resume                 = ata_scsi_device_resume,
 };
 
 static const struct ata_port_operations ahci_ops = {
@@ -257,6 +266,9 @@ static const struct ata_port_operations ahci_ops = {
         .error_handler          = ahci_error_handler,
         .post_internal_cmd      = ahci_post_internal_cmd,
 
+        .port_suspend           = ahci_port_suspend,
+        .port_resume            = ahci_port_resume,
+
         .port_start             = ahci_port_start,
         .port_stop              = ahci_port_stop,
 };
@@ -265,7 +277,7 @@ static const struct ata_port_info ahci_port_info[] = {
         /* board_ahci */
         {
                 .sht            = &ahci_sht,
-                .host_flags     = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+                .flags          = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
                                   ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA |
                                   ATA_FLAG_SKIP_D2H_BSY,
                 .pio_mask       = 0x1f, /* pio0-4 */
@@ -275,7 +287,7 @@ static const struct ata_port_info ahci_port_info[] = {
         /* board_ahci_vt8251 */
         {
                 .sht            = &ahci_sht,
-                .host_flags     = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+                .flags          = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
                                   ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA |
                                   ATA_FLAG_SKIP_D2H_BSY |
                                   AHCI_FLAG_RESET_NEEDS_CLO | AHCI_FLAG_NO_NCQ,
@@ -350,6 +362,14 @@ static const struct pci_device_id ahci_pci_tbl[] = {
         { PCI_VENDOR_ID_NVIDIA, 0x044f, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
           board_ahci },         /* MCP65 */
 
+        /* SiS */
+        { PCI_VENDOR_ID_SI, 0x1184, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+          board_ahci }, /* SiS 966 */
+        { PCI_VENDOR_ID_SI, 0x1185, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+          board_ahci }, /* SiS 966 */
+        { PCI_VENDOR_ID_SI, 0x0186, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+          board_ahci }, /* SiS 968 */
+
         { }     /* terminate list */
 };
 
@@ -358,6 +378,8 @@ static struct pci_driver ahci_pci_driver = {
         .name                   = DRV_NAME,
         .id_table               = ahci_pci_tbl,
         .probe                  = ahci_init_one,
+        .suspend                = ahci_pci_device_suspend,
+        .resume                 = ahci_pci_device_resume,
         .remove                 = ahci_remove_one,
 };
 
@@ -372,177 +394,288 @@ static inline void __iomem *ahci_port_base (void __iomem *base, unsigned int por
         return (void __iomem *) ahci_port_base_ul((unsigned long)base, port);
 }
 
-static int ahci_port_start(struct ata_port *ap)
+static u32 ahci_scr_read (struct ata_port *ap, unsigned int sc_reg_in)
 {
-        struct device *dev = ap->host_set->dev;
-        struct ahci_host_priv *hpriv = ap->host_set->private_data;
-        struct ahci_port_priv *pp;
-        void __iomem *mmio = ap->host_set->mmio_base;
-        void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
-        void *mem;
-        dma_addr_t mem_dma;
-        int rc;
-
-        pp = kmalloc(sizeof(*pp), GFP_KERNEL);
-        if (!pp)
-                return -ENOMEM;
-        memset(pp, 0, sizeof(*pp));
+        unsigned int sc_reg;
 
-        rc = ata_pad_alloc(ap, dev);
-        if (rc) {
-                kfree(pp);
-                return rc;
+        switch (sc_reg_in) {
+        case SCR_STATUS:        sc_reg = 0; break;
+        case SCR_CONTROL:       sc_reg = 1; break;
+        case SCR_ERROR:         sc_reg = 2; break;
+        case SCR_ACTIVE:        sc_reg = 3; break;
+        default:
+                return 0xffffffffU;
         }
 
-        mem = dma_alloc_coherent(dev, AHCI_PORT_PRIV_DMA_SZ, &mem_dma, GFP_KERNEL);
-        if (!mem) {
-                ata_pad_free(ap, dev);
-                kfree(pp);
-                return -ENOMEM;
-        }
-        memset(mem, 0, AHCI_PORT_PRIV_DMA_SZ);
+        return readl((void __iomem *) ap->ioaddr.scr_addr + (sc_reg * 4));
+}
 
-        /*
-         * First item in chunk of DMA memory: 32-slot command table,
-         * 32 bytes each in size
-         */
-        pp->cmd_slot = mem;
-        pp->cmd_slot_dma = mem_dma;
 
-        mem += AHCI_CMD_SLOT_SZ;
-        mem_dma += AHCI_CMD_SLOT_SZ;
+static void ahci_scr_write (struct ata_port *ap, unsigned int sc_reg_in,
+                               u32 val)
+{
+        unsigned int sc_reg;
 
-        /*
-         * Second item: Received-FIS area
-         */
-        pp->rx_fis = mem;
-        pp->rx_fis_dma = mem_dma;
+        switch (sc_reg_in) {
+        case SCR_STATUS:        sc_reg = 0; break;
+        case SCR_CONTROL:       sc_reg = 1; break;
+        case SCR_ERROR:         sc_reg = 2; break;
+        case SCR_ACTIVE:        sc_reg = 3; break;
+        default:
+                return;
+        }
 
-        mem += AHCI_RX_FIS_SZ;
-        mem_dma += AHCI_RX_FIS_SZ;
+        writel(val, (void __iomem *) ap->ioaddr.scr_addr + (sc_reg * 4));
+}
 
-        /*
-         * Third item: data area for storing a single command
-         * and its scatter-gather table
-         */
-        pp->cmd_tbl = mem;
-        pp->cmd_tbl_dma = mem_dma;
+static void ahci_start_engine(void __iomem *port_mmio)
+{
+        u32 tmp;
 
-        ap->private_data = pp;
+        /* start DMA */
+        tmp = readl(port_mmio + PORT_CMD);
+        tmp |= PORT_CMD_START;
+        writel(tmp, port_mmio + PORT_CMD);
+        readl(port_mmio + PORT_CMD); /* flush */
+}
 
-        if (hpriv->cap & HOST_CAP_64)
-                writel((pp->cmd_slot_dma >> 16) >> 16, port_mmio + PORT_LST_ADDR_HI);
-        writel(pp->cmd_slot_dma & 0xffffffff, port_mmio + PORT_LST_ADDR);
-        readl(port_mmio + PORT_LST_ADDR); /* flush */
+static int ahci_stop_engine(void __iomem *port_mmio)
+{
+        u32 tmp;
 
-        if (hpriv->cap & HOST_CAP_64)
-                writel((pp->rx_fis_dma >> 16) >> 16, port_mmio + PORT_FIS_ADDR_HI);
-        writel(pp->rx_fis_dma & 0xffffffff, port_mmio + PORT_FIS_ADDR);
-        readl(port_mmio + PORT_FIS_ADDR); /* flush */
+        tmp = readl(port_mmio + PORT_CMD);
 
-        writel(PORT_CMD_ICC_ACTIVE | PORT_CMD_FIS_RX |
-               PORT_CMD_POWER_ON | PORT_CMD_SPIN_UP |
-               PORT_CMD_START, port_mmio + PORT_CMD);
-        readl(port_mmio + PORT_CMD); /* flush */
+        /* check if the HBA is idle */
+        if ((tmp & (PORT_CMD_START | PORT_CMD_LIST_ON)) == 0)
+                return 0;
+
+        /* setting HBA to idle */
+        tmp &= ~PORT_CMD_START;
+        writel(tmp, port_mmio + PORT_CMD);
+
+        /* wait for engine to stop. This could be as long as 500 msec */
+        tmp = ata_wait_register(port_mmio + PORT_CMD,
+                                PORT_CMD_LIST_ON, PORT_CMD_LIST_ON, 1, 500);
+        if (tmp & PORT_CMD_LIST_ON)
+                return -EIO;
 
         return 0;
 }
 
+static void ahci_start_fis_rx(void __iomem *port_mmio, u32 cap,
+                              dma_addr_t cmd_slot_dma, dma_addr_t rx_fis_dma)
+{
+        u32 tmp;
 
-static void ahci_port_stop(struct ata_port *ap)
+        /* set FIS registers */
+        if (cap & HOST_CAP_64)
+                writel((cmd_slot_dma >> 16) >> 16, port_mmio + PORT_LST_ADDR_HI);
+        writel(cmd_slot_dma & 0xffffffff, port_mmio + PORT_LST_ADDR);
+
+        if (cap & HOST_CAP_64)
+                writel((rx_fis_dma >> 16) >> 16, port_mmio + PORT_FIS_ADDR_HI);
+        writel(rx_fis_dma & 0xffffffff, port_mmio + PORT_FIS_ADDR);
+
+        /* enable FIS reception */
+        tmp = readl(port_mmio + PORT_CMD);
+        tmp |= PORT_CMD_FIS_RX;
+        writel(tmp, port_mmio + PORT_CMD);
+
+        /* flush */
+        readl(port_mmio + PORT_CMD);
+}
+
+static int ahci_stop_fis_rx(void __iomem *port_mmio)
 {
-        struct device *dev = ap->host_set->dev;
-        struct ahci_port_priv *pp = ap->private_data;
-        void __iomem *mmio = ap->host_set->mmio_base;
-        void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
         u32 tmp;
 
+        /* disable FIS reception */
         tmp = readl(port_mmio + PORT_CMD);
-        tmp &= ~(PORT_CMD_START | PORT_CMD_FIS_RX);
+        tmp &= ~PORT_CMD_FIS_RX;
         writel(tmp, port_mmio + PORT_CMD);
-        readl(port_mmio + PORT_CMD); /* flush */
 
-        /* spec says 500 msecs for each PORT_CMD_{START,FIS_RX} bit, so
-         * this is slightly incorrect.
-         */
-        msleep(500);
+        /* wait for completion, spec says 500ms, give it 1000 */
+        tmp = ata_wait_register(port_mmio + PORT_CMD, PORT_CMD_FIS_ON,
+                                PORT_CMD_FIS_ON, 10, 1000);
+        if (tmp & PORT_CMD_FIS_ON)
+                return -EBUSY;
 
-        ap->private_data = NULL;
-        dma_free_coherent(dev, AHCI_PORT_PRIV_DMA_SZ,
-                          pp->cmd_slot, pp->cmd_slot_dma);
-        ata_pad_free(ap, dev);
-        kfree(pp);
+        return 0;
 }
 
-static u32 ahci_scr_read (struct ata_port *ap, unsigned int sc_reg_in)
+static void ahci_power_up(void __iomem *port_mmio, u32 cap)
 {
-        unsigned int sc_reg;
+        u32 cmd;
 
-        switch (sc_reg_in) {
-        case SCR_STATUS:        sc_reg = 0; break;
-        case SCR_CONTROL:       sc_reg = 1; break;
-        case SCR_ERROR:         sc_reg = 2; break;
-        case SCR_ACTIVE:        sc_reg = 3; break;
-        default:
-                return 0xffffffffU;
+        cmd = readl(port_mmio + PORT_CMD) & ~PORT_CMD_ICC_MASK;
+
+        /* spin up device */
+        if (cap & HOST_CAP_SSS) {
+                cmd |= PORT_CMD_SPIN_UP;
+                writel(cmd, port_mmio + PORT_CMD);
         }
 
-        return readl((void __iomem *) ap->ioaddr.scr_addr + (sc_reg * 4));
+        /* wake up link */
+        writel(cmd | PORT_CMD_ICC_ACTIVE, port_mmio + PORT_CMD);
 }
 
+static void ahci_power_down(void __iomem *port_mmio, u32 cap)
+{
+        u32 cmd, scontrol;
 
-static void ahci_scr_write (struct ata_port *ap, unsigned int sc_reg_in,
-                               u32 val)
+        cmd = readl(port_mmio + PORT_CMD) & ~PORT_CMD_ICC_MASK;
+
+        if (cap & HOST_CAP_SSC) {
+                /* enable transitions to slumber mode */
+                scontrol = readl(port_mmio + PORT_SCR_CTL);
+                if ((scontrol & 0x0f00) > 0x100) {
+                        scontrol &= ~0xf00;
+                        writel(scontrol, port_mmio + PORT_SCR_CTL);
+                }
+
+                /* put device into slumber mode */
+                writel(cmd | PORT_CMD_ICC_SLUMBER, port_mmio + PORT_CMD);
+
+                /* wait for the transition to complete */
+                ata_wait_register(port_mmio + PORT_CMD, PORT_CMD_ICC_SLUMBER,
+                                  PORT_CMD_ICC_SLUMBER, 1, 50);
+        }
+
+        /* put device into listen mode */
+        if (cap & HOST_CAP_SSS) {
+                /* first set PxSCTL.DET to 0 */
+                scontrol = readl(port_mmio + PORT_SCR_CTL);
+                scontrol &= ~0xf;
+                writel(scontrol, port_mmio + PORT_SCR_CTL);
+
+                /* then set PxCMD.SUD to 0 */
+                cmd &= ~PORT_CMD_SPIN_UP;
+                writel(cmd, port_mmio + PORT_CMD);
+        }
+}
+
+static void ahci_init_port(void __iomem *port_mmio, u32 cap,
+                           dma_addr_t cmd_slot_dma, dma_addr_t rx_fis_dma)
 {
-        unsigned int sc_reg;
+        /* power up */
+        ahci_power_up(port_mmio, cap);
 
-        switch (sc_reg_in) {
-        case SCR_STATUS:        sc_reg = 0; break;
-        case SCR_CONTROL:       sc_reg = 1; break;
-        case SCR_ERROR:         sc_reg = 2; break;
-        case SCR_ACTIVE:        sc_reg = 3; break;
-        default:
-                return;
+        /* enable FIS reception */
+        ahci_start_fis_rx(port_mmio, cap, cmd_slot_dma, rx_fis_dma);
+
+        /* enable DMA */
+        ahci_start_engine(port_mmio);
+}
+
+static int ahci_deinit_port(void __iomem *port_mmio, u32 cap, const char **emsg)
+{
+        int rc;
+
+        /* disable DMA */
+        rc = ahci_stop_engine(port_mmio);
+        if (rc) {
+                *emsg = "failed to stop engine";
+                return rc;
         }
 
-        writel(val, (void __iomem *) ap->ioaddr.scr_addr + (sc_reg * 4));
+        /* disable FIS reception */
+        rc = ahci_stop_fis_rx(port_mmio);
+        if (rc) {
+                *emsg = "failed stop FIS RX";
+                return rc;
+        }
+
+        /* put device into slumber mode */
+        ahci_power_down(port_mmio, cap);
+
+        return 0;
 }
 
-static int ahci_stop_engine(struct ata_port *ap)
+static int ahci_reset_controller(void __iomem *mmio, struct pci_dev *pdev)
 {
-        void __iomem *mmio = ap->host_set->mmio_base;
-        void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
-        int work;
-        u32 tmp;
+        u32 cap_save, tmp;
 
-        tmp = readl(port_mmio + PORT_CMD);
-        tmp &= ~PORT_CMD_START;
-        writel(tmp, port_mmio + PORT_CMD);
+        cap_save = readl(mmio + HOST_CAP);
+        cap_save &= ( (1<<28) | (1<<17) );
+        cap_save |= (1 << 27);
+
+        /* global controller reset */
+        tmp = readl(mmio + HOST_CTL);
+        if ((tmp & HOST_RESET) == 0) {
+                writel(tmp | HOST_RESET, mmio + HOST_CTL);
+                readl(mmio + HOST_CTL); /* flush */
+        }
 
-        /* wait for engine to stop.  TODO: this could be
-         * as long as 500 msec
+        /* reset must complete within 1 second, or
+         * the hardware should be considered fried.
          */
-        work = 1000;
-        while (work-- > 0) {
-                tmp = readl(port_mmio + PORT_CMD);
-                if ((tmp & PORT_CMD_LIST_ON) == 0)
-                        return 0;
-                udelay(10);
+        ssleep(1);
+
+        tmp = readl(mmio + HOST_CTL);
+        if (tmp & HOST_RESET) {
+                dev_printk(KERN_ERR, &pdev->dev,
+                           "controller reset failed (0x%x)\n", tmp);
+                return -EIO;
         }
 
-        return -EIO;
+        writel(HOST_AHCI_EN, mmio + HOST_CTL);
+        (void) readl(mmio + HOST_CTL);  /* flush */
+        writel(cap_save, mmio + HOST_CAP);
+        writel(0xf, mmio + HOST_PORTS_IMPL);
+        (void) readl(mmio + HOST_PORTS_IMPL);   /* flush */
+
+        if (pdev->vendor == PCI_VENDOR_ID_INTEL) {
+                u16 tmp16;
+
+                /* configure PCS */
+                pci_read_config_word(pdev, 0x92, &tmp16);
+                tmp16 |= 0xf;
+                pci_write_config_word(pdev, 0x92, tmp16);
+        }
+
+        return 0;
 }
 
-static void ahci_start_engine(struct ata_port *ap)
+static void ahci_init_controller(void __iomem *mmio, struct pci_dev *pdev,
+                                 int n_ports, u32 cap)
 {
-        void __iomem *mmio = ap->host_set->mmio_base;
-        void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
+        int i, rc;
         u32 tmp;
 
-        tmp = readl(port_mmio + PORT_CMD);
-        tmp |= PORT_CMD_START;
-        writel(tmp, port_mmio + PORT_CMD);
-        readl(port_mmio + PORT_CMD); /* flush */
+        for (i = 0; i < n_ports; i++) {
+                void __iomem *port_mmio = ahci_port_base(mmio, i);
+                const char *emsg = NULL;
+
+#if 0 /* BIOSen initialize this incorrectly */
+                if (!(hpriv->port_map & (1 << i)))
+                        continue;
+#endif
+
+                /* make sure port is not active */
+                rc = ahci_deinit_port(port_mmio, cap, &emsg);
+                if (rc)
+                        dev_printk(KERN_WARNING, &pdev->dev,
+                                   "%s (%d)\n", emsg, rc);
+
+                /* clear SError */
+                tmp = readl(port_mmio + PORT_SCR_ERR);
+                VPRINTK("PORT_SCR_ERR 0x%x\n", tmp);
+                writel(tmp, port_mmio + PORT_SCR_ERR);
+
+                /* clear port IRQ */
+                tmp = readl(port_mmio + PORT_IRQ_STAT);
+                VPRINTK("PORT_IRQ_STAT 0x%x\n", tmp);
+                if (tmp)
+                        writel(tmp, port_mmio + PORT_IRQ_STAT);
+
+                writel(1 << i, mmio + HOST_IRQ_STAT);
+        }
+
+        tmp = readl(mmio + HOST_CTL);
+        VPRINTK("HOST_CTL 0x%x\n", tmp);
+        writel(tmp | HOST_IRQ_EN, mmio + HOST_CTL);
+        tmp = readl(mmio + HOST_CTL);
+        VPRINTK("HOST_CTL 0x%x\n", tmp);
 }
 
 static unsigned int ahci_dev_classify(struct ata_port *ap)
@@ -576,7 +709,7 @@ static void ahci_fill_cmd_slot(struct ahci_port_priv *pp, unsigned int tag,
 static int ahci_clo(struct ata_port *ap)
 {
         void __iomem *port_mmio = (void __iomem *) ap->ioaddr.cmd_addr;
-        struct ahci_host_priv *hpriv = ap->host_set->private_data;
+        struct ahci_host_priv *hpriv = ap->host->private_data;
         u32 tmp;
 
         if (!(hpriv->cap & HOST_CAP_CLO))
@@ -608,7 +741,7 @@ static int ahci_prereset(struct ata_port *ap)
 static int ahci_softreset(struct ata_port *ap, unsigned int *class)
 {
         struct ahci_port_priv *pp = ap->private_data;
-        void __iomem *mmio = ap->host_set->mmio_base;
+        void __iomem *mmio = ap->host->mmio_base;
         void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
         const u32 cmd_fis_len = 5; /* five dwords */
         const char *reason = NULL;
@@ -626,7 +759,7 @@ static int ahci_softreset(struct ata_port *ap, unsigned int *class)
         }
 
         /* prepare for SRST (AHCI-1.1 10.4.1) */
-        rc = ahci_stop_engine(ap);
+        rc = ahci_stop_engine(port_mmio);
         if (rc) {
                 reason = "failed to stop engine";
                 goto fail_restart;
@@ -647,7 +780,7 @@ static int ahci_softreset(struct ata_port *ap, unsigned int *class)
         }
 
         /* restart engine */
-        ahci_start_engine(ap);
+        ahci_start_engine(port_mmio);
 
         ata_tf_init(ap->device, &tf);
         fis = pp->cmd_tbl;
@@ -706,7 +839,7 @@ static int ahci_softreset(struct ata_port *ap, unsigned int *class)
         return 0;
 
  fail_restart:
-        ahci_start_engine(ap);
+        ahci_start_engine(port_mmio);
  fail:
         ata_port_printk(ap, KERN_ERR, "softreset failed (%s)\n", reason);
         return rc;
@@ -717,11 +850,13 @@ static int ahci_hardreset(struct ata_port *ap, unsigned int *class)
         struct ahci_port_priv *pp = ap->private_data;
         u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
         struct ata_taskfile tf;
+        void __iomem *mmio = ap->host->mmio_base;
+        void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
         int rc;
 
         DPRINTK("ENTER\n");
 
-        ahci_stop_engine(ap);
+        ahci_stop_engine(port_mmio);
 
         /* clear D2H reception area to properly wait for D2H FIS */
         ata_tf_init(ap->device, &tf);
@@ -730,7 +865,7 @@ static int ahci_hardreset(struct ata_port *ap, unsigned int *class)
 
         rc = sata_std_hardreset(ap, class);
 
-        ahci_start_engine(ap);
+        ahci_start_engine(port_mmio);
 
         if (rc == 0 && ata_port_online(ap))
                 *class = ahci_dev_classify(ap);
@@ -904,7 +1039,7 @@ static void ahci_error_intr(struct ata_port *ap, u32 irq_stat)
 
 static void ahci_host_intr(struct ata_port *ap)
 {
-        void __iomem *mmio = ap->host_set->mmio_base;
+        void __iomem *mmio = ap->host->mmio_base;
         void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
         struct ata_eh_info *ehi = &ap->eh_info;
         u32 status, qc_active;
@@ -940,7 +1075,7 @@ static void ahci_host_intr(struct ata_port *ap)
                 return;
 
         /* ignore interim PIO setup fis interrupts */
-        if (ata_tag_valid(ap->active_tag) && (status & PORT_IRQ_PIOS_FIS)) 
+        if (ata_tag_valid(ap->active_tag) && (status & PORT_IRQ_PIOS_FIS))
                 return;
 
         if (ata_ratelimit())
@@ -956,7 +1091,7 @@ static void ahci_irq_clear(struct ata_port *ap)
 
 static irqreturn_t ahci_interrupt(int irq, void *dev_instance, struct pt_regs *regs)
 {
-        struct ata_host_set *host_set = dev_instance;
+        struct ata_host *host = dev_instance;
         struct ahci_host_priv *hpriv;
         unsigned int i, handled = 0;
         void __iomem *mmio;
@@ -964,8 +1099,8 @@ static irqreturn_t ahci_interrupt(int irq, void *dev_instance, struct pt_regs *r
 
         VPRINTK("ENTER\n");
 
-        hpriv = host_set->private_data;
-        mmio = host_set->mmio_base;
+        hpriv = host->private_data;
+        mmio = host->mmio_base;
 
         /* sigh.  0xffffffff is a valid return from h/w */
         irq_stat = readl(mmio + HOST_IRQ_STAT);
@@ -973,22 +1108,22 @@ static irqreturn_t ahci_interrupt(int irq, void *dev_instance, struct pt_regs *r
         if (!irq_stat)
                 return IRQ_NONE;
 
-        spin_lock(&host_set->lock);
+        spin_lock(&host->lock);
 
-        for (i = 0; i < host_set->n_ports; i++) {
+        for (i = 0; i < host->n_ports; i++) {
                 struct ata_port *ap;
 
                 if (!(irq_stat & (1 << i)))
                         continue;
 
-                ap = host_set->ports[i];
+                ap = host->ports[i];
                 if (ap) {
                         ahci_host_intr(ap);
                         VPRINTK("port %u\n", i);
                 } else {
                         VPRINTK("port %u (no irq)\n", i);
                         if (ata_ratelimit())
-                                dev_printk(KERN_WARNING, host_set->dev,
+                                dev_printk(KERN_WARNING, host->dev,
                                         "interrupt on disabled port %u\n", i);
                 }
 
@@ -1000,7 +1135,7 @@ static irqreturn_t ahci_interrupt(int irq, void *dev_instance, struct pt_regs *r
                 handled = 1;
         }
 
-        spin_unlock(&host_set->lock);
+        spin_unlock(&host->lock);
 
         VPRINTK("EXIT\n");
 
@@ -1022,7 +1157,7 @@ static unsigned int ahci_qc_issue(struct ata_queued_cmd *qc)
 
 static void ahci_freeze(struct ata_port *ap)
 {
-        void __iomem *mmio = ap->host_set->mmio_base;
+        void __iomem *mmio = ap->host->mmio_base;
         void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
 
         /* turn IRQ off */
@@ -1031,7 +1166,7 @@ static void ahci_freeze(struct ata_port *ap)
 
 static void ahci_thaw(struct ata_port *ap)
 {
-        void __iomem *mmio = ap->host_set->mmio_base;
+        void __iomem *mmio = ap->host->mmio_base;
         void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
         u32 tmp;
 
@@ -1046,10 +1181,13 @@ static void ahci_thaw(struct ata_port *ap)
 
 static void ahci_error_handler(struct ata_port *ap)
 {
+        void __iomem *mmio = ap->host->mmio_base;
+        void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
+
         if (!(ap->pflags & ATA_PFLAG_FROZEN)) {
                 /* restart engine */
-                ahci_stop_engine(ap);
-                ahci_start_engine(ap);
+                ahci_stop_engine(port_mmio);
+                ahci_start_engine(port_mmio);
         }
 
         /* perform recovery */
@@ -1060,15 +1198,176 @@ static void ahci_error_handler(struct ata_port *ap)
 static void ahci_post_internal_cmd(struct ata_queued_cmd *qc)
 {
         struct ata_port *ap = qc->ap;
+        void __iomem *mmio = ap->host->mmio_base;
+        void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
 
         if (qc->flags & ATA_QCFLAG_FAILED)
                 qc->err_mask |= AC_ERR_OTHER;
 
         if (qc->err_mask) {
                 /* make DMA engine forget about the failed command */
-                ahci_stop_engine(ap);
-                ahci_start_engine(ap);
+                ahci_stop_engine(port_mmio);
+                ahci_start_engine(port_mmio);
+        }
+}
+
+static int ahci_port_suspend(struct ata_port *ap, pm_message_t mesg)
+{
+        struct ahci_host_priv *hpriv = ap->host->private_data;
+        struct ahci_port_priv *pp = ap->private_data;
+        void __iomem *mmio = ap->host->mmio_base;
+        void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
+        const char *emsg = NULL;
+        int rc;
+
+        rc = ahci_deinit_port(port_mmio, hpriv->cap, &emsg);
+        if (rc) {
+                ata_port_printk(ap, KERN_ERR, "%s (%d)\n", emsg, rc);
+                ahci_init_port(port_mmio, hpriv->cap,
+                               pp->cmd_slot_dma, pp->rx_fis_dma);
+        }
+
+        return rc;
+}
+
+static int ahci_port_resume(struct ata_port *ap)
+{
+        struct ahci_port_priv *pp = ap->private_data;
+        struct ahci_host_priv *hpriv = ap->host->private_data;
+        void __iomem *mmio = ap->host->mmio_base;
+        void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
+
+        ahci_init_port(port_mmio, hpriv->cap, pp->cmd_slot_dma, pp->rx_fis_dma);
+
+        return 0;
+}
+
+static int ahci_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
+{
+        struct ata_host *host = dev_get_drvdata(&pdev->dev);
+        void __iomem *mmio = host->mmio_base;
+        u32 ctl;
+
+        if (mesg.event == PM_EVENT_SUSPEND) {
+                /* AHCI spec rev1.1 section 8.3.3:
+                 * Software must disable interrupts prior to requesting a
+                 * transition of the HBA to D3 state.
+                 */
+                ctl = readl(mmio + HOST_CTL);
+                ctl &= ~HOST_IRQ_EN;
+                writel(ctl, mmio + HOST_CTL);
+                readl(mmio + HOST_CTL); /* flush */
+        }
+
+        return ata_pci_device_suspend(pdev, mesg);
+}
+
+static int ahci_pci_device_resume(struct pci_dev *pdev)
+{
+        struct ata_host *host = dev_get_drvdata(&pdev->dev);
+        struct ahci_host_priv *hpriv = host->private_data;
+        void __iomem *mmio = host->mmio_base;
+        int rc;
+
+        ata_pci_device_do_resume(pdev);
+
+        if (pdev->dev.power.power_state.event == PM_EVENT_SUSPEND) {
+                rc = ahci_reset_controller(mmio, pdev);
+                if (rc)
+                        return rc;
+
+                ahci_init_controller(mmio, pdev, host->n_ports, hpriv->cap);
         }
+
+        ata_host_resume(host);
+
+        return 0;
+}
+
+static int ahci_port_start(struct ata_port *ap)
+{
+        struct device *dev = ap->host->dev;
+        struct ahci_host_priv *hpriv = ap->host->private_data;
+        struct ahci_port_priv *pp;
+        void __iomem *mmio = ap->host->mmio_base;
+        void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
+        void *mem;
+        dma_addr_t mem_dma;
+        int rc;
+
+        pp = kmalloc(sizeof(*pp), GFP_KERNEL);
+        if (!pp)
+                return -ENOMEM;
+        memset(pp, 0, sizeof(*pp));
+
+        rc = ata_pad_alloc(ap, dev);
+        if (rc) {
+                kfree(pp);
+                return rc;
+        }
+
+        mem = dma_alloc_coherent(dev, AHCI_PORT_PRIV_DMA_SZ, &mem_dma, GFP_KERNEL);
+        if (!mem) {
+                ata_pad_free(ap, dev);
+                kfree(pp);
+                return -ENOMEM;
+        }
+        memset(mem, 0, AHCI_PORT_PRIV_DMA_SZ);
+
+        /*
+         * First item in chunk of DMA memory: 32-slot command table,
+         * 32 bytes each in size
+         */
+        pp->cmd_slot = mem;
+        pp->cmd_slot_dma = mem_dma;
+
+        mem += AHCI_CMD_SLOT_SZ;
+        mem_dma += AHCI_CMD_SLOT_SZ;
+
+        /*
+         * Second item: Received-FIS area
+         */
+        pp->rx_fis = mem;
+        pp->rx_fis_dma = mem_dma;
+
+        mem += AHCI_RX_FIS_SZ;
+        mem_dma += AHCI_RX_FIS_SZ;
+
+        /*
+         * Third item: data area for storing a single command
+         * and its scatter-gather table
+         */
+        pp->cmd_tbl = mem;
+        pp->cmd_tbl_dma = mem_dma;
+
+        ap->private_data = pp;
+
+        /* initialize port */
+        ahci_init_port(port_mmio, hpriv->cap, pp->cmd_slot_dma, pp->rx_fis_dma);
+
+        return 0;
+}
+
+static void ahci_port_stop(struct ata_port *ap)
+{
+        struct device *dev = ap->host->dev;
+        struct ahci_host_priv *hpriv = ap->host->private_data;
+        struct ahci_port_priv *pp = ap->private_data;
+        void __iomem *mmio = ap->host->mmio_base;
+        void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
+        const char *emsg = NULL;
+        int rc;
+
+        /* de-initialize port */
+        rc = ahci_deinit_port(port_mmio, hpriv->cap, &emsg);
+        if (rc)
+                ata_port_printk(ap, KERN_WARNING, "%s (%d)\n", emsg, rc);
+
+        ap->private_data = NULL;
+        dma_free_coherent(dev, AHCI_PORT_PRIV_DMA_SZ,
+                          pp->cmd_slot, pp->cmd_slot_dma);
+        ata_pad_free(ap, dev);
+        kfree(pp);
 }
 
 static void ahci_setup_port(struct ata_ioports *port, unsigned long base,
@@ -1089,47 +1388,12 @@ static int ahci_host_init(struct ata_probe_ent *probe_ent)
         struct ahci_host_priv *hpriv = probe_ent->private_data;
         struct pci_dev *pdev = to_pci_dev(probe_ent->dev);
         void __iomem *mmio = probe_ent->mmio_base;
-        u32 tmp, cap_save;
-        unsigned int i, j, using_dac;
+        unsigned int i, using_dac;
         int rc;
-        void __iomem *port_mmio;
-
-        cap_save = readl(mmio + HOST_CAP);
-        cap_save &= ( (1<<28) | (1<<17) );
-        cap_save |= (1 << 27);
 
-        /* global controller reset */
-        tmp = readl(mmio + HOST_CTL);
-        if ((tmp & HOST_RESET) == 0) {
-                writel(tmp | HOST_RESET, mmio + HOST_CTL);
-                readl(mmio + HOST_CTL); /* flush */
-        }
-
-        /* reset must complete within 1 second, or
-         * the hardware should be considered fried.
-         */
-        ssleep(1);
-
-        tmp = readl(mmio + HOST_CTL);
-        if (tmp & HOST_RESET) {
-                dev_printk(KERN_ERR, &pdev->dev,
-                           "controller reset failed (0x%x)\n", tmp);
-                return -EIO;
-        }
-
-        writel(HOST_AHCI_EN, mmio + HOST_CTL);
-        (void) readl(mmio + HOST_CTL);  /* flush */
-        writel(cap_save, mmio + HOST_CAP);
-        writel(0xf, mmio + HOST_PORTS_IMPL);
-        (void) readl(mmio + HOST_PORTS_IMPL);   /* flush */
-
-        if (pdev->vendor == PCI_VENDOR_ID_INTEL) {
-                u16 tmp16;
-
-                pci_read_config_word(pdev, 0x92, &tmp16);
-                tmp16 |= 0xf;
-                pci_write_config_word(pdev, 0x92, tmp16);
-        }
+        rc = ahci_reset_controller(mmio, pdev);
+        if (rc)
+                return rc;
 
         hpriv->cap = readl(mmio + HOST_CAP);
         hpriv->port_map = readl(mmio + HOST_PORTS_IMPL);
@@ -1165,63 +1429,10 @@ static int ahci_host_init(struct ata_probe_ent *probe_ent)
                 }
         }
 
-        for (i = 0; i < probe_ent->n_ports; i++) {
-#if 0 /* BIOSen initialize this incorrectly */
-                if (!(hpriv->port_map & (1 << i)))
-                        continue;
-#endif
-
-                port_mmio = ahci_port_base(mmio, i);
-                VPRINTK("mmio %p  port_mmio %p\n", mmio, port_mmio);
-
-                ahci_setup_port(&probe_ent->port[i],
-                                (unsigned long) mmio, i);
+        for (i = 0; i < probe_ent->n_ports; i++)
+                ahci_setup_port(&probe_ent->port[i], (unsigned long) mmio, i);
 
-                /* make sure port is not active */
-                tmp = readl(port_mmio + PORT_CMD);
-                VPRINTK("PORT_CMD 0x%x\n", tmp);
-                if (tmp & (PORT_CMD_LIST_ON | PORT_CMD_FIS_ON |
-                           PORT_CMD_FIS_RX | PORT_CMD_START)) {
-                        tmp &= ~(PORT_CMD_LIST_ON | PORT_CMD_FIS_ON |
-                                 PORT_CMD_FIS_RX | PORT_CMD_START);
-                        writel(tmp, port_mmio + PORT_CMD);
-                        readl(port_mmio + PORT_CMD); /* flush */
-
-                        /* spec says 500 msecs for each bit, so
-                         * this is slightly incorrect.
-                         */
-                        msleep(500);
-                }
-
-                writel(PORT_CMD_SPIN_UP, port_mmio + PORT_CMD);
-
-                j = 0;
-                while (j < 100) {
-                        msleep(10);
-                        tmp = readl(port_mmio + PORT_SCR_STAT);
-                        if ((tmp & 0xf) == 0x3)
-                                break;
-                        j++;
-                }
-
-                tmp = readl(port_mmio + PORT_SCR_ERR);
-                VPRINTK("PORT_SCR_ERR 0x%x\n", tmp);
-                writel(tmp, port_mmio + PORT_SCR_ERR);
-
-                /* ack any pending irq events for this port */
-                tmp = readl(port_mmio + PORT_IRQ_STAT);
-                VPRINTK("PORT_IRQ_STAT 0x%x\n", tmp);
-                if (tmp)
-                        writel(tmp, port_mmio + PORT_IRQ_STAT);
-
-                writel(1 << i, mmio + HOST_IRQ_STAT);
-        }
-
-        tmp = readl(mmio + HOST_CTL);
-        VPRINTK("HOST_CTL 0x%x\n", tmp);
-        writel(tmp | HOST_IRQ_EN, mmio + HOST_CTL);
-        tmp = readl(mmio + HOST_CTL);
-        VPRINTK("HOST_CTL 0x%x\n", tmp);
+        ahci_init_controller(mmio, pdev, probe_ent->n_ports, hpriv->cap);
 
         pci_set_master(pdev);
 
@@ -1370,7 +1581,7 @@ static int ahci_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
         memset(hpriv, 0, sizeof(*hpriv));
 
         probe_ent->sht          = ahci_port_info[board_idx].sht;
-        probe_ent->host_flags   = ahci_port_info[board_idx].host_flags;
+        probe_ent->port_flags   = ahci_port_info[board_idx].flags;
         probe_ent->pio_mask     = ahci_port_info[board_idx].pio_mask;
         probe_ent->udma_mask    = ahci_port_info[board_idx].udma_mask;
         probe_ent->port_ops     = ahci_port_info[board_idx].port_ops;
@@ -1388,9 +1599,9 @@ static int ahci_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
         if (rc)
                 goto err_out_hpriv;
 
-        if (!(probe_ent->host_flags & AHCI_FLAG_NO_NCQ) &&
+        if (!(probe_ent->port_flags & AHCI_FLAG_NO_NCQ) &&
             (hpriv->cap & HOST_CAP_NCQ))
-                probe_ent->host_flags |= ATA_FLAG_NCQ;
+                probe_ent->port_flags |= ATA_FLAG_NCQ;
 
         ahci_print_info(probe_ent);
 
@@ -1421,27 +1632,27 @@ err_out:
 static void ahci_remove_one (struct pci_dev *pdev)
 {
         struct device *dev = pci_dev_to_dev(pdev);
-        struct ata_host_set *host_set = dev_get_drvdata(dev);
-        struct ahci_host_priv *hpriv = host_set->private_data;
+        struct ata_host *host = dev_get_drvdata(dev);
+        struct ahci_host_priv *hpriv = host->private_data;
         unsigned int i;
         int have_msi;
 
-        for (i = 0; i < host_set->n_ports; i++)
-                ata_port_detach(host_set->ports[i]);
+        for (i = 0; i < host->n_ports; i++)
+                ata_port_detach(host->ports[i]);
 
         have_msi = hpriv->flags & AHCI_FLAG_MSI;
-        free_irq(host_set->irq, host_set);
+        free_irq(host->irq, host);
 
-        for (i = 0; i < host_set->n_ports; i++) {
-                struct ata_port *ap = host_set->ports[i];
+        for (i = 0; i < host->n_ports; i++) {
+                struct ata_port *ap = host->ports[i];
 
-                ata_scsi_release(ap->host);
-                scsi_host_put(ap->host);
+                ata_scsi_release(ap->scsi_host);
+                scsi_host_put(ap->scsi_host);
         }
 
         kfree(hpriv);
-        pci_iounmap(pdev, host_set->mmio_base);
-        kfree(host_set);
+        pci_iounmap(pdev, host->mmio_base);
+        kfree(host);
 
         if (have_msi)
                 pci_disable_msi(pdev);
@@ -1454,7 +1665,7 @@ static void ahci_remove_one (struct pci_dev *pdev)
 
 static int __init ahci_init(void)
 {
-        return pci_module_init(&ahci_pci_driver);
+        return pci_register_driver(&ahci_pci_driver);
 }
 
 static void __exit ahci_exit(void)
diff --git a/drivers/ata/ata_generic.c b/drivers/ata/ata_generic.c
new file mode 100644
index 000000000000..1d1c30a2fcd0
--- /dev/null
+++ b/drivers/ata/ata_generic.c
@@ -0,0 +1,252 @@
+/*
+ *  ata_generic.c - Generic PATA/SATA controller driver.
+ *  Copyright 2005 Red Hat Inc <alan@redhat.com>, all rights reserved.
+ *
+ *  Elements from ide/pci/generic.c
+ *          Copyright (C) 2001-2002     Andre Hedrick <andre@linux-ide.org>
+ *          Portions (C) Copyright 2002  Red Hat Inc <alan@redhat.com>
+ *
+ *  May be copied or modified under the terms of the GNU General Public License
+ *
+ *  Driver for PCI IDE interfaces implementing the standard bus mastering
+ *  interface functionality. This assumes the BIOS did the drive set up and
+ *  tuning for us. By default we do not grab all IDE class devices as they
+ *  may have other drivers or need fixups to avoid problems. Instead we keep
+ *  a default list of stuff without documentation/driver that appears to
+ *  work.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "ata_generic"
+#define DRV_VERSION "0.2.6"
+
+/*
+ *      A generic parallel ATA driver using libata
+ */
+
+/**
+ *      generic_pre_reset               -       probe begin
+ *      @ap: ATA port
+ *
+ *      Set up cable type and use generic probe init
+ */
+
+static int generic_pre_reset(struct ata_port *ap)
+{
+        ap->cbl = ATA_CBL_PATA80;
+        return ata_std_prereset(ap);
+}
+
+
+/**
+ *      generic_error_handler - Probe specified port on PATA host controller
+ *      @ap: Port to probe
+ *      @classes:
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+
+static void generic_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, generic_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      generic_set_mode        -       mode setting
+ *      @ap: interface to set up
+ *
+ *      Use a non standard set_mode function. We don't want to be tuned.
+ *      The BIOS configured everything. Our job is not to fiddle. We
+ *      read the dma enabled bits from the PCI configuration of the device
+ *      and respect them.
+ */
+
+static void generic_set_mode(struct ata_port *ap)
+{
+        int dma_enabled = 0;
+        int i;
+
+        /* Bits 5 and 6 indicate if DMA is active on master/slave */
+        if (ap->ioaddr.bmdma_addr)
+                dma_enabled = inb(ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
+
+        for (i = 0; i < ATA_MAX_DEVICES; i++) {
+                struct ata_device *dev = &ap->device[i];
+                if (ata_dev_enabled(dev)) {
+                        /* We don't really care */
+                        dev->pio_mode = XFER_PIO_0;
+                        dev->dma_mode = XFER_MW_DMA_0;
+                        /* We do need the right mode information for DMA or PIO
+                           and this comes from the current configuration flags */
+                        if (dma_enabled & (1 << (5 + i))) {
+                                dev->xfer_mode = XFER_MW_DMA_0;
+                                dev->xfer_shift = ATA_SHIFT_MWDMA;
+                                dev->flags &= ~ATA_DFLAG_PIO;
+                        } else {
+                                dev->xfer_mode = XFER_PIO_0;
+                                dev->xfer_shift = ATA_SHIFT_PIO;
+                                dev->flags |= ATA_DFLAG_PIO;
+                        }
+                }
+        }
+}
+
+static struct scsi_host_template generic_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations generic_port_ops = {
+        .set_mode       = generic_set_mode,
+
+        .port_disable   = ata_port_disable,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .data_xfer      = ata_pio_data_xfer,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = generic_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static int all_generic_ide;             /* Set to claim all devices */
+
+/**
+ *      ata_generic_init                -       attach generic IDE
+ *      @dev: PCI device found
+ *      @id: match entry
+ *
+ *      Called each time a matching IDE interface is found. We check if the
+ *      interface is one we wish to claim and if so we perform any chip
+ *      specific hacks then let the ATA layer do the heavy lifting.
+ */
+
+static int ata_generic_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+        u16 command;
+        static struct ata_port_info info = {
+                .sht = &generic_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x3f,
+                .port_ops = &generic_port_ops
+        };
+        static struct ata_port_info *port_info[2] = { &info, &info };
+
+        /* Don't use the generic entry unless instructed to do so */
+        if (id->driver_data == 1 && all_generic_ide == 0)
+                return -ENODEV;
+
+        /* Devices that need care */
+        if (dev->vendor == PCI_VENDOR_ID_UMC &&
+            dev->device == PCI_DEVICE_ID_UMC_UM8886A &&
+            (!(PCI_FUNC(dev->devfn) & 1)))
+                return -ENODEV;
+
+        if (dev->vendor == PCI_VENDOR_ID_OPTI &&
+            dev->device == PCI_DEVICE_ID_OPTI_82C558 &&
+            (!(PCI_FUNC(dev->devfn) & 1)))
+                return -ENODEV;
+
+        /* Don't re-enable devices in generic mode or we will break some
+           motherboards with disabled and unused IDE controllers */
+        pci_read_config_word(dev, PCI_COMMAND, &command);
+        if (!(command & PCI_COMMAND_IO))
+                return -ENODEV;
+
+        if (dev->vendor == PCI_VENDOR_ID_AL)
+                ata_pci_clear_simplex(dev);
+
+        return ata_pci_init_one(dev, port_info, 2);
+}
+
+static struct pci_device_id ata_generic[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_PCTECH, PCI_DEVICE_ID_PCTECH_SAMURAI_IDE), },
+        { PCI_DEVICE(PCI_VENDOR_ID_HOLTEK, PCI_DEVICE_ID_HOLTEK_6565), },
+        { PCI_DEVICE(PCI_VENDOR_ID_UMC,    PCI_DEVICE_ID_UMC_UM8673F), },
+        { PCI_DEVICE(PCI_VENDOR_ID_UMC,    PCI_DEVICE_ID_UMC_UM8886A), },
+        { PCI_DEVICE(PCI_VENDOR_ID_UMC,    PCI_DEVICE_ID_UMC_UM8886BF), },
+        { PCI_DEVICE(PCI_VENDOR_ID_HINT,   PCI_DEVICE_ID_HINT_VXPROII_IDE), },
+        { PCI_DEVICE(PCI_VENDOR_ID_VIA,    PCI_DEVICE_ID_VIA_82C561), },
+        { PCI_DEVICE(PCI_VENDOR_ID_OPTI,   PCI_DEVICE_ID_OPTI_82C558), },
+        { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO), },
+        { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_1), },
+        { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_2),  },
+        /* Must come last. If you add entries adjust this table appropriately */
+        { PCI_ANY_ID,           PCI_ANY_ID,                        PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_STORAGE_IDE << 8, 0xFFFFFF00UL, 1},
+        { 0, },
+};
+
+static struct pci_driver ata_generic_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = ata_generic,
+        .probe          = ata_generic_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init ata_generic_init(void)
+{
+        return pci_module_init(&ata_generic_pci_driver);
+}
+
+
+static void __exit ata_generic_exit(void)
+{
+        pci_unregister_driver(&ata_generic_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for generic ATA");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, ata_generic);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(ata_generic_init);
+module_exit(ata_generic_exit);
+
+module_param(all_generic_ide, int, 0);
diff --git a/drivers/scsi/ata_piix.c b/drivers/ata/ata_piix.c
index a9bb3cb7e89b..965b4f0ba711 100644
--- a/drivers/scsi/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -93,7 +93,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME        "ata_piix"
-#define DRV_VERSION     "2.00"
+#define DRV_VERSION     "2.00ac6"
 
 enum {
         PIIX_IOCFG              = 0x54, /* IDE I/O configuration register */
@@ -116,15 +116,18 @@ enum {
         PIIX_80C_SEC            = (1 << 7) | (1 << 6),
 
         /* controller IDs */
-        piix4_pata              = 0,
-        ich5_pata               = 1,
-        ich5_sata               = 2,
-        esb_sata                = 3,
-        ich6_sata               = 4,
-        ich6_sata_ahci          = 5,
-        ich6m_sata_ahci         = 6,
-        ich7m_sata_ahci         = 7,
-        ich8_sata_ahci          = 8,
+        piix_pata_33            = 0,    /* PIIX3 or 4 at 33Mhz */
+        ich_pata_33             = 1,    /* ICH up to UDMA 33 only */
+        ich_pata_66             = 2,    /* ICH up to 66 Mhz */
+        ich_pata_100            = 3,    /* ICH up to UDMA 100 */
+        ich_pata_133            = 4,    /* ICH up to UDMA 133 */
+        ich5_sata               = 5,
+        esb_sata                = 6,
+        ich6_sata               = 7,
+        ich6_sata_ahci          = 8,
+        ich6m_sata_ahci         = 9,
+        ich7m_sata_ahci         = 10,
+        ich8_sata_ahci          = 11,
 
         /* constants for mapping table */
         P0                      = 0,  /* port 0 */
@@ -152,20 +155,55 @@ struct piix_host_priv {
 
 static int piix_init_one (struct pci_dev *pdev,
                                     const struct pci_device_id *ent);
-static void piix_host_stop(struct ata_host_set *host_set);
-static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev);
-static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev);
+static void piix_host_stop(struct ata_host *host);
 static void piix_pata_error_handler(struct ata_port *ap);
+static void ich_pata_error_handler(struct ata_port *ap);
 static void piix_sata_error_handler(struct ata_port *ap);
+static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev);
+static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev);
+static void ich_set_dmamode (struct ata_port *ap, struct ata_device *adev);
 
 static unsigned int in_module_init = 1;
 
 static const struct pci_device_id piix_pci_tbl[] = {
 #ifdef ATA_ENABLE_PATA
-        { 0x8086, 0x7111, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix4_pata },
-        { 0x8086, 0x24db, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_pata },
-        { 0x8086, 0x25a2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_pata },
-        { 0x8086, 0x27df, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_pata },
+        /* Intel PIIX4 for the 430TX/440BX/MX chipset: UDMA 33 */
+        /* Also PIIX4E (fn3 rev 2) and PIIX4M (fn3 rev 3) */
+        { 0x8086, 0x7111, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 },
+        { 0x8086, 0x24db, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+        { 0x8086, 0x25a2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+        /* Intel PIIX4 */
+        { 0x8086, 0x7199, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 },
+        /* Intel PIIX4 */
+        { 0x8086, 0x7601, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 },
+        /* Intel PIIX */
+        { 0x8086, 0x84CA, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 },
+        /* Intel ICH (i810, i815, i840) UDMA 66*/
+        { 0x8086, 0x2411, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_66 },
+        /* Intel ICH0 : UDMA 33*/
+        { 0x8086, 0x2421, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_33 },
+        /* Intel ICH2M */
+        { 0x8086, 0x244A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+        /* Intel ICH2 (i810E2, i845, 850, 860) UDMA 100 */
+        { 0x8086, 0x244B, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+        /*  Intel ICH3M */
+        { 0x8086, 0x248A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+        /* Intel ICH3 (E7500/1) UDMA 100 */
+        { 0x8086, 0x248B, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+        /* Intel ICH4 (i845GV, i845E, i852, i855) UDMA 100 */
+        { 0x8086, 0x24CA, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+        { 0x8086, 0x24CB, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+        /* Intel ICH5 */
+        { 0x8086, 0x24DB, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_133 },
+        /* C-ICH (i810E2) */
+        { 0x8086, 0x245B, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+        /* ESB (855GME/875P + 6300ESB) UDMA 100  */
+        { 0x8086, 0x25A2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+        /* ICH6 (and 6) (i915) UDMA 100 */
+        { 0x8086, 0x266F, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+        /* ICH7/7-R (i945, i975) UDMA 100*/
+        { 0x8086, 0x27DF, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_133 },
+        { 0x8086, 0x269E, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
 #endif
 
         /* NOTE: The following PCI ids must be kept in sync with the
@@ -264,6 +302,39 @@ static const struct ata_port_operations piix_pata_ops = {
         .host_stop              = piix_host_stop,
 };
 
+static const struct ata_port_operations ich_pata_ops = {
+        .port_disable           = ata_port_disable,
+        .set_piomode            = piix_set_piomode,
+        .set_dmamode            = ich_set_dmamode,
+        .mode_filter            = ata_pci_default_filter,
+
+        .tf_load                = ata_tf_load,
+        .tf_read                = ata_tf_read,
+        .check_status           = ata_check_status,
+        .exec_command           = ata_exec_command,
+        .dev_select             = ata_std_dev_select,
+
+        .bmdma_setup            = ata_bmdma_setup,
+        .bmdma_start            = ata_bmdma_start,
+        .bmdma_stop             = ata_bmdma_stop,
+        .bmdma_status           = ata_bmdma_status,
+        .qc_prep                = ata_qc_prep,
+        .qc_issue               = ata_qc_issue_prot,
+        .data_xfer              = ata_pio_data_xfer,
+
+        .freeze                 = ata_bmdma_freeze,
+        .thaw                   = ata_bmdma_thaw,
+        .error_handler          = ich_pata_error_handler,
+        .post_internal_cmd      = ata_bmdma_post_internal_cmd,
+
+        .irq_handler            = ata_interrupt,
+        .irq_clear              = ata_bmdma_irq_clear,
+
+        .port_start             = ata_port_start,
+        .port_stop              = ata_port_stop,
+        .host_stop              = ata_host_stop,
+};
+
 static const struct ata_port_operations piix_sata_ops = {
         .port_disable           = ata_port_disable,
 
@@ -379,38 +450,59 @@ static const struct piix_map_db *piix_map_db_table[] = {
 };
 
 static struct ata_port_info piix_port_info[] = {
-        /* piix4_pata */
+        /* piix_pata_33: 0:  PIIX3 or 4 at 33MHz */
         {
                 .sht            = &piix_sht,
-                .host_flags     = ATA_FLAG_SLAVE_POSS,
+                .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
                 .pio_mask       = 0x1f, /* pio0-4 */
-#if 0
-                .mwdma_mask     = 0x06, /* mwdma1-2 */
-#else
-                .mwdma_mask     = 0x00, /* mwdma broken */
-#endif
+                .mwdma_mask     = 0x06, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
                 .udma_mask      = ATA_UDMA_MASK_40C,
                 .port_ops       = &piix_pata_ops,
         },
 
-        /* ich5_pata */
+        /* ich_pata_33: 1       ICH0 - ICH at 33Mhz*/
+        {
+                .sht            = &piix_sht,
+                .flags          = ATA_FLAG_SRST | ATA_FLAG_SLAVE_POSS,
+                .pio_mask       = 0x1f, /* pio 0-4 */
+                .mwdma_mask     = 0x06, /* Check: maybe 0x07  */
+                .udma_mask      = ATA_UDMA2, /* UDMA33 */
+                .port_ops       = &ich_pata_ops,
+        },
+        /* ich_pata_66: 2       ICH controllers up to 66MHz */
+        {
+                .sht            = &piix_sht,
+                .flags          = ATA_FLAG_SRST | ATA_FLAG_SLAVE_POSS,
+                .pio_mask       = 0x1f, /* pio 0-4 */
+                .mwdma_mask     = 0x06, /* MWDMA0 is broken on chip */
+                .udma_mask      = ATA_UDMA4,
+                .port_ops       = &ich_pata_ops,
+        },
+
+        /* ich_pata_100: 3 */
         {
                 .sht            = &piix_sht,
-                .host_flags     = ATA_FLAG_SLAVE_POSS | PIIX_FLAG_CHECKINTR,
+                .flags          = ATA_FLAG_SRST | ATA_FLAG_SLAVE_POSS | PIIX_FLAG_CHECKINTR,
                 .pio_mask       = 0x1f, /* pio0-4 */
-#if 0
                 .mwdma_mask     = 0x06, /* mwdma1-2 */
-#else
-                .mwdma_mask     = 0x00, /* mwdma broken */
-#endif
-                .udma_mask      = 0x3f, /* udma0-5 */
-                .port_ops       = &piix_pata_ops,
+                .udma_mask      = ATA_UDMA5, /* udma0-5 */
+                .port_ops       = &ich_pata_ops,
+        },
+
+        /* ich_pata_133: 4      ICH with full UDMA6 */
+        {
+                .sht            = &piix_sht,
+                .flags          = ATA_FLAG_SRST | ATA_FLAG_SLAVE_POSS | PIIX_FLAG_CHECKINTR,
+                .pio_mask       = 0x1f, /* pio 0-4 */
+                .mwdma_mask     = 0x06, /* Check: maybe 0x07  */
+                .udma_mask      = ATA_UDMA6, /* UDMA133 */
+                .port_ops       = &ich_pata_ops,
         },
 
-        /* ich5_sata */
+        /* ich5_sata: 5 */
         {
                 .sht            = &piix_sht,
-                .host_flags     = ATA_FLAG_SATA | PIIX_FLAG_CHECKINTR |
+                .flags          = ATA_FLAG_SATA | PIIX_FLAG_CHECKINTR |
                                   PIIX_FLAG_IGNORE_PCS,
                 .pio_mask       = 0x1f, /* pio0-4 */
                 .mwdma_mask     = 0x07, /* mwdma0-2 */
@@ -418,10 +510,10 @@ static struct ata_port_info piix_port_info[] = {
                 .port_ops       = &piix_sata_ops,
         },
 
-        /* i6300esb_sata */
+        /* i6300esb_sata: 6 */
         {
                 .sht            = &piix_sht,
-                .host_flags     = ATA_FLAG_SATA |
+                .flags          = ATA_FLAG_SATA |
                                   PIIX_FLAG_CHECKINTR | PIIX_FLAG_IGNORE_PCS,
                 .pio_mask       = 0x1f, /* pio0-4 */
                 .mwdma_mask     = 0x07, /* mwdma0-2 */
@@ -429,10 +521,10 @@ static struct ata_port_info piix_port_info[] = {
                 .port_ops       = &piix_sata_ops,
         },
 
-        /* ich6_sata */
+        /* ich6_sata: 7 */
         {
                 .sht            = &piix_sht,
-                .host_flags     = ATA_FLAG_SATA |
+                .flags          = ATA_FLAG_SATA |
                                   PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR,
                 .pio_mask       = 0x1f, /* pio0-4 */
                 .mwdma_mask     = 0x07, /* mwdma0-2 */
@@ -440,10 +532,10 @@ static struct ata_port_info piix_port_info[] = {
                 .port_ops       = &piix_sata_ops,
         },
 
-        /* ich6_sata_ahci */
+        /* ich6_sata_ahci: 8 */
         {
                 .sht            = &piix_sht,
-                .host_flags     = ATA_FLAG_SATA |
+                .flags          = ATA_FLAG_SATA |
                                   PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR |
                                   PIIX_FLAG_AHCI,
                 .pio_mask       = 0x1f, /* pio0-4 */
@@ -452,10 +544,10 @@ static struct ata_port_info piix_port_info[] = {
                 .port_ops       = &piix_sata_ops,
         },
 
-        /* ich6m_sata_ahci */
+        /* ich6m_sata_ahci: 9 */
         {
                 .sht            = &piix_sht,
-                .host_flags     = ATA_FLAG_SATA |
+                .flags          = ATA_FLAG_SATA |
                                   PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR |
                                   PIIX_FLAG_AHCI,
                 .pio_mask       = 0x1f, /* pio0-4 */
@@ -464,7 +556,7 @@ static struct ata_port_info piix_port_info[] = {
                 .port_ops       = &piix_sata_ops,
         },
 
-        /* ich7m_sata_ahci */
+        /* ich7m_sata_ahci: 10 */
         {
                 .sht            = &piix_sht,
                 .host_flags     = ATA_FLAG_SATA |
@@ -476,10 +568,10 @@ static struct ata_port_info piix_port_info[] = {
                 .port_ops       = &piix_sata_ops,
         },
 
-        /* ich8_sata_ahci */
+        /* ich8_sata_ahci: 11 */
         {
                 .sht            = &piix_sht,
-                .host_flags     = ATA_FLAG_SATA |
+                .flags          = ATA_FLAG_SATA |
                                   PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR |
                                   PIIX_FLAG_AHCI,
                 .pio_mask       = 0x1f, /* pio0-4 */
@@ -487,6 +579,7 @@ static struct ata_port_info piix_port_info[] = {
                 .udma_mask      = 0x7f, /* udma0-6 */
                 .port_ops       = &piix_sata_ops,
         },
+
 };
 
 static struct pci_bits piix_enable_bits[] = {
@@ -515,9 +608,10 @@ MODULE_PARM_DESC(force_pcs, "force honoring or ignoring PCS to work around "
  *      LOCKING:
  *      None (inherited from caller).
  */
-static void piix_pata_cbl_detect(struct ata_port *ap)
+
+static void ich_pata_cbl_detect(struct ata_port *ap)
 {
-        struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
         u8 tmp, mask;
 
         /* no 80c support in host controller? */
@@ -525,7 +619,7 @@ static void piix_pata_cbl_detect(struct ata_port *ap)
                 goto cbl40;
 
         /* check BIOS cable detect results */
-        mask = ap->hard_port_no == 0 ? PIIX_80C_PRI : PIIX_80C_SEC;
+        mask = ap->port_no == 0 ? PIIX_80C_PRI : PIIX_80C_SEC;
         pci_read_config_byte(pdev, PIIX_IOCFG, &tmp);
         if ((tmp & mask) == 0)
                 goto cbl40;
@@ -535,30 +629,26 @@ static void piix_pata_cbl_detect(struct ata_port *ap)
 
 cbl40:
         ap->cbl = ATA_CBL_PATA40;
-        ap->udma_mask &= ATA_UDMA_MASK_40C;
 }
 
 /**
  *      piix_pata_prereset - prereset for PATA host controller
  *      @ap: Target port
  *
- *      Prereset including cable detection.
  *
  *      LOCKING:
  *      None (inherited from caller).
  */
 static int piix_pata_prereset(struct ata_port *ap)
 {
-        struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 
-        if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->hard_port_no])) {
+        if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->port_no])) {
                 ata_port_printk(ap, KERN_INFO, "port disabled. ignoring.\n");
                 ap->eh_context.i.action &= ~ATA_EH_RESET_MASK;
                 return 0;
         }
-
-        piix_pata_cbl_detect(ap);
-
+        ap->cbl = ATA_CBL_PATA40;
         return ata_std_prereset(ap);
 }
 
@@ -568,6 +658,36 @@ static void piix_pata_error_handler(struct ata_port *ap)
                            ata_std_postreset);
 }
 
+
+/**
+ *      ich_pata_prereset - prereset for PATA host controller
+ *      @ap: Target port
+ *
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+static int ich_pata_prereset(struct ata_port *ap)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+        if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->port_no])) {
+                ata_port_printk(ap, KERN_INFO, "port disabled. ignoring.\n");
+                ap->eh_context.i.action &= ~ATA_EH_RESET_MASK;
+                return 0;
+        }
+
+        ich_pata_cbl_detect(ap);
+
+        return ata_std_prereset(ap);
+}
+
+static void ich_pata_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, ich_pata_prereset, ata_std_softreset, NULL,
+                           ata_std_postreset);
+}
+
 /**
  *      piix_sata_present_mask - determine present mask for SATA host controller
  *      @ap: Target port
@@ -583,10 +703,10 @@ static void piix_pata_error_handler(struct ata_port *ap)
  */
 static unsigned int piix_sata_present_mask(struct ata_port *ap)
 {
-        struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
-        struct piix_host_priv *hpriv = ap->host_set->private_data;
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        struct piix_host_priv *hpriv = ap->host->private_data;
         const unsigned int *map = hpriv->map;
-        int base = 2 * ap->hard_port_no;
+        int base = 2 * ap->port_no;
         unsigned int present_mask = 0;
         int port, i;
         u16 pcs;
@@ -663,12 +783,19 @@ static void piix_sata_error_handler(struct ata_port *ap)
 static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev)
 {
         unsigned int pio        = adev->pio_mode - XFER_PIO_0;
-        struct pci_dev *dev     = to_pci_dev(ap->host_set->dev);
+        struct pci_dev *dev     = to_pci_dev(ap->host->dev);
         unsigned int is_slave   = (adev->devno != 0);
-        unsigned int master_port= ap->hard_port_no ? 0x42 : 0x40;
+        unsigned int master_port= ap->port_no ? 0x42 : 0x40;
         unsigned int slave_port = 0x44;
         u16 master_data;
         u8 slave_data;
+        u8 udma_enable;
+        int control = 0;
+
+        /*
+         *      See Intel Document 298600-004 for the timing programing rules
+         *      for ICH controllers.
+         */
 
         static const     /* ISP  RTC */
         u8 timings[][2] = { { 0, 0 },
@@ -677,20 +804,30 @@ static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev)
                             { 2, 1 },
                             { 2, 3 }, };
 
+        if (pio >= 2)
+                control |= 1;   /* TIME1 enable */
+        if (ata_pio_need_iordy(adev))
+                control |= 2;   /* IE enable */
+
+        /* Intel specifies that the PPE functionality is for disk only */
+        if (adev->class == ATA_DEV_ATA)
+                control |= 4;   /* PPE enable */
+
         pci_read_config_word(dev, master_port, &master_data);
         if (is_slave) {
+                /* Enable SITRE (seperate slave timing register) */
                 master_data |= 0x4000;
-                /* enable PPE, IE and TIME */
-                master_data |= 0x0070;
+                /* enable PPE1, IE1 and TIME1 as needed */
+                master_data |= (control << 4);
                 pci_read_config_byte(dev, slave_port, &slave_data);
-                slave_data &= (ap->hard_port_no ? 0x0f : 0xf0);
-                slave_data |=
-                        (timings[pio][0] << 2) |
-                        (timings[pio][1] << (ap->hard_port_no ? 4 : 0));
+                slave_data &= (ap->port_no ? 0x0f : 0xf0);
+                /* Load the timing nibble for this slave */
+                slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
         } else {
+                /* Master keeps the bits in a different format */
                 master_data &= 0xccf8;
-                /* enable PPE, IE and TIME */
-                master_data |= 0x0007;
+                /* Enable PPE, IE and TIME as appropriate */
+                master_data |= control;
                 master_data |=
                         (timings[pio][0] << 12) |
                         (timings[pio][1] << 8);
@@ -698,13 +835,23 @@ static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev)
         pci_write_config_word(dev, master_port, master_data);
         if (is_slave)
                 pci_write_config_byte(dev, slave_port, slave_data);
+
+        /* Ensure the UDMA bit is off - it will be turned back on if
+           UDMA is selected */
+
+        if (ap->udma_mask) {
+                pci_read_config_byte(dev, 0x48, &udma_enable);
+                udma_enable &= ~(1 << (2 * ap->port_no + adev->devno));
+                pci_write_config_byte(dev, 0x48, udma_enable);
+        }
 }
 
 /**
- *      piix_set_dmamode - Initialize host controller PATA PIO timings
+ *      do_pata_set_dmamode - Initialize host controller PATA PIO timings
  *      @ap: Port whose timings we are configuring
- *      @adev: um
+ *      @adev: Drive in question
  *      @udma: udma mode, 0 - 6
+ *      @is_ich: set if the chip is an ICH device
  *
  *      Set UDMA mode for device, in host controller PCI config space.
  *
@@ -712,70 +859,140 @@ static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev)
  *      None (inherited from caller).
  */
 
-static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+static void do_pata_set_dmamode (struct ata_port *ap, struct ata_device *adev, int isich)
 {
-        unsigned int udma       = adev->dma_mode; /* FIXME: MWDMA too */
-        struct pci_dev *dev     = to_pci_dev(ap->host_set->dev);
-        u8 maslave              = ap->hard_port_no ? 0x42 : 0x40;
-        u8 speed                = udma;
-        unsigned int drive_dn   = (ap->hard_port_no ? 2 : 0) + adev->devno;
-        int a_speed             = 3 << (drive_dn * 4);
-        int u_flag              = 1 << drive_dn;
-        int v_flag              = 0x01 << drive_dn;
-        int w_flag              = 0x10 << drive_dn;
-        int u_speed             = 0;
-        int                     sitre;
-        u16                     reg4042, reg4a;
-        u8                      reg48, reg54, reg55;
-
-        pci_read_config_word(dev, maslave, &reg4042);
-        DPRINTK("reg4042 = 0x%04x\n", reg4042);
-        sitre = (reg4042 & 0x4000) ? 1 : 0;
-        pci_read_config_byte(dev, 0x48, &reg48);
-        pci_read_config_word(dev, 0x4a, &reg4a);
-        pci_read_config_byte(dev, 0x54, &reg54);
-        pci_read_config_byte(dev, 0x55, &reg55);
-
-        switch(speed) {
-                case XFER_UDMA_4:
-                case XFER_UDMA_2:       u_speed = 2 << (drive_dn * 4); break;
-                case XFER_UDMA_6:
-                case XFER_UDMA_5:
-                case XFER_UDMA_3:
-                case XFER_UDMA_1:       u_speed = 1 << (drive_dn * 4); break;
-                case XFER_UDMA_0:       u_speed = 0 << (drive_dn * 4); break;
-                case XFER_MW_DMA_2:
-                case XFER_MW_DMA_1:     break;
-                default:
-                        BUG();
-                        return;
-        }
+        struct pci_dev *dev     = to_pci_dev(ap->host->dev);
+        u8 master_port          = ap->port_no ? 0x42 : 0x40;
+        u16 master_data;
+        u8 speed                = adev->dma_mode;
+        int devid               = adev->devno + 2 * ap->port_no;
+        u8 udma_enable;
+
+        static const     /* ISP  RTC */
+        u8 timings[][2] = { { 0, 0 },
+                            { 0, 0 },
+                            { 1, 0 },
+                            { 2, 1 },
+                            { 2, 3 }, };
+
+        pci_read_config_word(dev, master_port, &master_data);
+        pci_read_config_byte(dev, 0x48, &udma_enable);
 
         if (speed >= XFER_UDMA_0) {
-                if (!(reg48 & u_flag))
-                        pci_write_config_byte(dev, 0x48, reg48 | u_flag);
-                if (speed == XFER_UDMA_5) {
-                        pci_write_config_byte(dev, 0x55, (u8) reg55|w_flag);
-                } else {
-                        pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
+                unsigned int udma = adev->dma_mode - XFER_UDMA_0;
+                u16 udma_timing;
+                u16 ideconf;
+                int u_clock, u_speed;
+
+                /*
+                 * UDMA is handled by a combination of clock switching and
+                 * selection of dividers
+                 *
+                 * Handy rule: Odd modes are UDMATIMx 01, even are 02
+                 *             except UDMA0 which is 00
+                 */
+                u_speed = min(2 - (udma & 1), udma);
+                if (udma == 5)
+                        u_clock = 0x1000;       /* 100Mhz */
+                else if (udma > 2)
+                        u_clock = 1;            /* 66Mhz */
+                else
+                        u_clock = 0;            /* 33Mhz */
+
+                udma_enable |= (1 << devid);
+
+                /* Load the CT/RP selection */
+                pci_read_config_word(dev, 0x4A, &udma_timing);
+                udma_timing &= ~(3 << (4 * devid));
+                udma_timing |= u_speed << (4 * devid);
+                pci_write_config_word(dev, 0x4A, udma_timing);
+
+                if (isich) {
+                        /* Select a 33/66/100Mhz clock */
+                        pci_read_config_word(dev, 0x54, &ideconf);
+                        ideconf &= ~(0x1001 << devid);
+                        ideconf |= u_clock << devid;
+                        /* For ICH or later we should set bit 10 for better
+                           performance (WR_PingPong_En) */
+                        pci_write_config_word(dev, 0x54, ideconf);
                 }
-                if ((reg4a & a_speed) != u_speed)
-                        pci_write_config_word(dev, 0x4a, (reg4a & ~a_speed) | u_speed);
-                if (speed > XFER_UDMA_2) {
-                        if (!(reg54 & v_flag))
-                                pci_write_config_byte(dev, 0x54, reg54 | v_flag);
-                } else
-                        pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
         } else {
-                if (reg48 & u_flag)
-                        pci_write_config_byte(dev, 0x48, reg48 & ~u_flag);
-                if (reg4a & a_speed)
-                        pci_write_config_word(dev, 0x4a, reg4a & ~a_speed);
-                if (reg54 & v_flag)
-                        pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
-                if (reg55 & w_flag)
-                        pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
+                /*
+                 * MWDMA is driven by the PIO timings. We must also enable
+                 * IORDY unconditionally along with TIME1. PPE has already
+                 * been set when the PIO timing was set.
+                 */
+                unsigned int mwdma      = adev->dma_mode - XFER_MW_DMA_0;
+                unsigned int control;
+                u8 slave_data;
+                const unsigned int needed_pio[3] = {
+                        XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
+                };
+                int pio = needed_pio[mwdma] - XFER_PIO_0;
+
+                control = 3;    /* IORDY|TIME1 */
+
+                /* If the drive MWDMA is faster than it can do PIO then
+                   we must force PIO into PIO0 */
+
+                if (adev->pio_mode < needed_pio[mwdma])
+                        /* Enable DMA timing only */
+                        control |= 8;   /* PIO cycles in PIO0 */
+
+                if (adev->devno) {      /* Slave */
+                        master_data &= 0xFF4F;  /* Mask out IORDY|TIME1|DMAONLY */
+                        master_data |= control << 4;
+                        pci_read_config_byte(dev, 0x44, &slave_data);
+                        slave_data &= (0x0F + 0xE1 * ap->port_no);
+                        /* Load the matching timing */
+                        slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
+                        pci_write_config_byte(dev, 0x44, slave_data);
+                } else {        /* Master */
+                        master_data &= 0xCCF4;  /* Mask out IORDY|TIME1|DMAONLY
+                                                   and master timing bits */
+                        master_data |= control;
+                        master_data |=
+                                (timings[pio][0] << 12) |
+                                (timings[pio][1] << 8);
+                }
+                udma_enable &= ~(1 << devid);
+                pci_write_config_word(dev, master_port, master_data);
         }
+        /* Don't scribble on 0x48 if the controller does not support UDMA */
+        if (ap->udma_mask)
+                pci_write_config_byte(dev, 0x48, udma_enable);
+}
+
+/**
+ *      piix_set_dmamode - Initialize host controller PATA DMA timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: um
+ *
+ *      Set MW/UDMA mode for device, in host controller PCI config space.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+        do_pata_set_dmamode(ap, adev, 0);
+}
+
+/**
+ *      ich_set_dmamode - Initialize host controller PATA DMA timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: um
+ *
+ *      Set MW/UDMA mode for device, in host controller PCI config space.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void ich_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+        do_pata_set_dmamode(ap, adev, 1);
 }
 
 #define AHCI_PCI_BAR 5
@@ -867,13 +1084,13 @@ static void __devinit piix_init_pcs(struct pci_dev *pdev,
         if (force_pcs == 1) {
                 dev_printk(KERN_INFO, &pdev->dev,
                            "force ignoring PCS (0x%x)\n", new_pcs);
-                pinfo[0].host_flags |= PIIX_FLAG_IGNORE_PCS;
-                pinfo[1].host_flags |= PIIX_FLAG_IGNORE_PCS;
+                pinfo[0].flags |= PIIX_FLAG_IGNORE_PCS;
+                pinfo[1].flags |= PIIX_FLAG_IGNORE_PCS;
         } else if (force_pcs == 2) {
                 dev_printk(KERN_INFO, &pdev->dev,
                            "force honoring PCS (0x%x)\n", new_pcs);
-                pinfo[0].host_flags &= ~PIIX_FLAG_IGNORE_PCS;
-                pinfo[1].host_flags &= ~PIIX_FLAG_IGNORE_PCS;
+                pinfo[0].flags &= ~PIIX_FLAG_IGNORE_PCS;
+                pinfo[1].flags &= ~PIIX_FLAG_IGNORE_PCS;
         }
 }
 
@@ -904,7 +1121,7 @@ static void __devinit piix_init_sata_map(struct pci_dev *pdev,
 
                 case IDE:
                         WARN_ON((i & 1) || map[i + 1] != IDE);
-                        pinfo[i / 2] = piix_port_info[ich5_pata];
+                        pinfo[i / 2] = piix_port_info[ich_pata_100];
                         pinfo[i / 2].private_data = hpriv;
                         i++;
                         printk(" IDE IDE");
@@ -913,7 +1130,7 @@ static void __devinit piix_init_sata_map(struct pci_dev *pdev,
                 default:
                         printk(" P%d", map[i]);
                         if (i & 1)
-                                pinfo[i / 2].host_flags |= ATA_FLAG_SLAVE_POSS;
+                                pinfo[i / 2].flags |= ATA_FLAG_SLAVE_POSS;
                         break;
                 }
         }
@@ -948,7 +1165,7 @@ static int piix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
         struct ata_port_info port_info[2];
         struct ata_port_info *ppinfo[2] = { &port_info[0], &port_info[1] };
         struct piix_host_priv *hpriv;
-        unsigned long host_flags;
+        unsigned long port_flags;
 
         if (!printed_version++)
                 dev_printk(KERN_DEBUG, &pdev->dev,
@@ -967,9 +1184,9 @@ static int piix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
         port_info[0].private_data = hpriv;
         port_info[1].private_data = hpriv;
 
-        host_flags = port_info[0].host_flags;
+        port_flags = port_info[0].flags;
 
-        if (host_flags & PIIX_FLAG_AHCI) {
+        if (port_flags & PIIX_FLAG_AHCI) {
                 u8 tmp;
                 pci_read_config_byte(pdev, PIIX_SCC, &tmp);
                 if (tmp == PIIX_AHCI_DEVICE) {
@@ -980,7 +1197,7 @@ static int piix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
         }
 
         /* Initialize SATA map */
-        if (host_flags & ATA_FLAG_SATA) {
+        if (port_flags & ATA_FLAG_SATA) {
                 piix_init_sata_map(pdev, port_info,
                                    piix_map_db_table[ent->driver_data]);
                 piix_init_pcs(pdev, port_info,
@@ -993,7 +1210,7 @@ static int piix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
          * MSI is disabled (and it is disabled, as we don't use
          * message-signalled interrupts currently).
          */
-        if (host_flags & PIIX_FLAG_CHECKINTR)
+        if (port_flags & PIIX_FLAG_CHECKINTR)
                 pci_intx(pdev, 1);
 
         if (piix_check_450nx_errata(pdev)) {
@@ -1008,19 +1225,21 @@ static int piix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
         return ata_pci_init_one(pdev, ppinfo, 2);
 }
 
-static void piix_host_stop(struct ata_host_set *host_set)
+static void piix_host_stop(struct ata_host *host)
 {
-        if (host_set->next == NULL)
-                kfree(host_set->private_data);
-        ata_host_stop(host_set);
+        struct piix_host_priv *hpriv = host->private_data;
+
+        ata_host_stop(host);
+
+        kfree(hpriv);
 }
 
 static int __init piix_init(void)
 {
         int rc;
 
-        DPRINTK("pci_module_init\n");
-        rc = pci_module_init(&piix_pci_driver);
+        DPRINTK("pci_register_driver\n");
+        rc = pci_register_driver(&piix_pci_driver);
         if (rc)
                 return rc;
 
@@ -1037,4 +1256,3 @@ static void __exit piix_exit(void)
 
 module_init(piix_init);
 module_exit(piix_exit);
-
diff --git a/drivers/scsi/libata-core.c b/drivers/ata/libata-core.c
index 73dd6c8deede..1c9315401f7a 100644
--- a/drivers/scsi/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -50,7 +50,6 @@
 #include <linux/jiffies.h>
 #include <linux/scatterlist.h>
 #include <scsi/scsi.h>
-#include "scsi_priv.h"
 #include <scsi/scsi_cmnd.h>
 #include <scsi/scsi_host.h>
 #include <linux/libata.h>
@@ -387,9 +386,13 @@ static const char *ata_mode_string(unsigned int xfer_mask)
                 "PIO2",
                 "PIO3",
                 "PIO4",
+                "PIO5",
+                "PIO6",
                 "MWDMA0",
                 "MWDMA1",
                 "MWDMA2",
+                "MWDMA3",
+                "MWDMA4",
                 "UDMA/16",
                 "UDMA/25",
                 "UDMA/33",
@@ -876,6 +879,23 @@ static unsigned int ata_id_xfermask(const u16 *id)
 
         mwdma_mask = id[ATA_ID_MWDMA_MODES] & 0x07;
 
+        if (ata_id_is_cfa(id)) {
+                /*
+                 *      Process compact flash extended modes
+                 */
+                int pio = id[163] & 0x7;
+                int dma = (id[163] >> 3) & 7;
+
+                if (pio)
+                        pio_mask |= (1 << 5);
+                if (pio > 1)
+                        pio_mask |= (1 << 6);
+                if (dma)
+                        mwdma_mask |= (1 << 3);
+                if (dma > 1)
+                        mwdma_mask |= (1 << 4);
+        }
+
         udma_mask = 0;
         if (id[ATA_ID_FIELD_VALID] & (1 << 2))
                 udma_mask = id[ATA_ID_UDMA_MODES] & 0xff;
@@ -1315,7 +1335,7 @@ static void ata_dev_config_ncq(struct ata_device *dev,
         }
 
         if (ap->flags & ATA_FLAG_NCQ) {
-                hdepth = min(ap->host->can_queue, ATA_MAX_QUEUE - 1);
+                hdepth = min(ap->scsi_host->can_queue, ATA_MAX_QUEUE - 1);
                 dev->flags |= ATA_DFLAG_NCQ;
         }
 
@@ -1329,12 +1349,13 @@ static void ata_set_port_max_cmd_len(struct ata_port *ap)
 {
         int i;
 
-        if (ap->host) {
-                ap->host->max_cmd_len = 0;
+        if (ap->scsi_host) {
+                unsigned int len = 0;
+
                 for (i = 0; i < ATA_MAX_DEVICES; i++)
-                        ap->host->max_cmd_len = max_t(unsigned int,
-                                                      ap->host->max_cmd_len,
-                                                      ap->device[i].cdb_len);
+                        len = max(len, ap->device[i].cdb_len);
+
+                ap->scsi_host->max_cmd_len = len;
         }
 }
 
@@ -1357,6 +1378,7 @@ int ata_dev_configure(struct ata_device *dev, int print_info)
         struct ata_port *ap = dev->ap;
         const u16 *id = dev->id;
         unsigned int xfer_mask;
+        char revbuf[7];         /* XYZ-99\0 */
         int rc;
 
         if (!ata_dev_enabled(dev) && ata_msg_info(ap)) {
@@ -1400,6 +1422,15 @@ int ata_dev_configure(struct ata_device *dev, int print_info)
 
         /* ATA-specific feature tests */
         if (dev->class == ATA_DEV_ATA) {
+                if (ata_id_is_cfa(id)) {
+                        if (id[162] & 1) /* CPRM may make this media unusable */
+                                ata_dev_printk(dev, KERN_WARNING, "ata%u: device %u  supports DRM functions and may not be fully accessable.\n",
+                                        ap->id, dev->devno);
+                        snprintf(revbuf, 7, "CFA");
+                }
+                else
+                        snprintf(revbuf, 7, "ATA-%d",  ata_id_major_version(id));
+
                 dev->n_sectors = ata_id_n_sectors(id);
 
                 if (ata_id_has_lba(id)) {
@@ -1418,9 +1449,9 @@ int ata_dev_configure(struct ata_device *dev, int print_info)
 
                         /* print device info to dmesg */
                         if (ata_msg_drv(ap) && print_info)
-                                ata_dev_printk(dev, KERN_INFO, "ATA-%d, "
+                                ata_dev_printk(dev, KERN_INFO, "%s, "
                                         "max %s, %Lu sectors: %s %s\n",
-                                        ata_id_major_version(id),
+                                        revbuf,
                                         ata_mode_string(xfer_mask),
                                         (unsigned long long)dev->n_sectors,
                                         lba_desc, ncq_desc);
@@ -1441,9 +1472,9 @@ int ata_dev_configure(struct ata_device *dev, int print_info)
 
                         /* print device info to dmesg */
                         if (ata_msg_drv(ap) && print_info)
-                                ata_dev_printk(dev, KERN_INFO, "ATA-%d, "
+                                ata_dev_printk(dev, KERN_INFO, "%s, "
                                         "max %s, %Lu sectors: CHS %u/%u/%u\n",
-                                        ata_id_major_version(id),
+                                        revbuf,
                                         ata_mode_string(xfer_mask),
                                         (unsigned long long)dev->n_sectors,
                                         dev->cylinders, dev->heads,
@@ -1528,7 +1559,7 @@ err_out_nosup:
  *      Zero on success, negative errno otherwise.
  */
 
-static int ata_bus_probe(struct ata_port *ap)
+int ata_bus_probe(struct ata_port *ap)
 {
         unsigned int classes[ATA_MAX_DEVICES];
         int tries[ATA_MAX_DEVICES];
@@ -1632,7 +1663,7 @@ static int ata_bus_probe(struct ata_port *ap)
  *      Modify @ap data structure such that the system
  *      thinks that the entire port is enabled.
  *
- *      LOCKING: host_set lock, or some other form of
+ *      LOCKING: host lock, or some other form of
  *      serialization.
  */
 
@@ -1770,7 +1801,7 @@ struct ata_device *ata_dev_pair(struct ata_device *adev)
  *      never attempt to probe or communicate with devices
  *      on this port.
  *
- *      LOCKING: host_set lock, or some other form of
+ *      LOCKING: host lock, or some other form of
  *      serialization.
  */
 
@@ -1901,10 +1932,11 @@ int sata_set_spd(struct ata_port *ap)
  * drivers/ide/ide-timing.h and was originally written by Vojtech Pavlik
  */
 /*
- * PIO 0-5, MWDMA 0-2 and UDMA 0-6 timings (in nanoseconds).
+ * PIO 0-4, MWDMA 0-2 and UDMA 0-6 timings (in nanoseconds).
  * These were taken from ATA/ATAPI-6 standard, rev 0a, except
- * for PIO 5, which is a nonstandard extension and UDMA6, which
- * is currently supported only by Maxtor drives.
+ * for UDMA6, which is currently supported only by Maxtor drives.
+ *
+ * For PIO 5/6 MWDMA 3/4 see the CFA specification 3.0.
  */
 
 static const struct ata_timing ata_timing[] = {
@@ -1914,6 +1946,8 @@ static const struct ata_timing ata_timing[] = {
         { XFER_UDMA_4,     0,   0,   0,   0,   0,   0,   0,  30 },
         { XFER_UDMA_3,     0,   0,   0,   0,   0,   0,   0,  45 },
 
+        { XFER_MW_DMA_4,  25,   0,   0,   0,  55,  20,  80,   0 },
+        { XFER_MW_DMA_3,  25,   0,   0,   0,  65,  25, 100,   0 },
         { XFER_UDMA_2,     0,   0,   0,   0,   0,   0,   0,  60 },
         { XFER_UDMA_1,     0,   0,   0,   0,   0,   0,   0,  80 },
         { XFER_UDMA_0,     0,   0,   0,   0,   0,   0,   0, 120 },
@@ -1928,7 +1962,8 @@ static const struct ata_timing ata_timing[] = {
         { XFER_SW_DMA_1,  90,   0,   0,   0, 240, 240, 480,   0 },
         { XFER_SW_DMA_0, 120,   0,   0,   0, 480, 480, 960,   0 },
 
-/*      { XFER_PIO_5,     20,  50,  30, 100,  50,  30, 100,   0 }, */
+        { XFER_PIO_6,     10,  55,  20,  80,  55,  20,  80,   0 },
+        { XFER_PIO_5,     15,  65,  25, 100,  65,  25, 100,   0 },
         { XFER_PIO_4,     25,  70,  25, 120,  70,  25, 120,   0 },
         { XFER_PIO_3,     30,  80,  70, 180,  80,  70, 180,   0 },
 
@@ -2224,8 +2259,8 @@ int ata_set_mode(struct ata_port *ap, struct ata_device **r_failed_dev)
         /* Record simplex status. If we selected DMA then the other
          * host channels are not permitted to do so.
          */
-        if (used_dma && (ap->host_set->flags & ATA_HOST_SIMPLEX))
-                ap->host_set->simplex_claimed = 1;
+        if (used_dma && (ap->host->flags & ATA_HOST_SIMPLEX))
+                ap->host->simplex_claimed = 1;
 
         /* step5: chip specific finalisation */
         if (ap->ops->post_set_mode)
@@ -2247,7 +2282,7 @@ int ata_set_mode(struct ata_port *ap, struct ata_device **r_failed_dev)
  *      other threads.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 static inline void ata_tf_to_host(struct ata_port *ap,
@@ -2411,7 +2446,7 @@ static unsigned int ata_bus_softreset(struct ata_port *ap,
  *
  *      LOCKING:
  *      PCI/etc. bus probe sem.
- *      Obtains host_set lock.
+ *      Obtains host lock.
  *
  *      SIDE EFFECTS:
  *      Sets ATA_FLAG_DISABLED if bus reset fails.
@@ -3040,20 +3075,16 @@ static int ata_dma_blacklisted(const struct ata_device *dev)
  *      known limits including host controller limits, device
  *      blacklist, etc...
  *
- *      FIXME: The current implementation limits all transfer modes to
- *      the fastest of the lowested device on the port.  This is not
- *      required on most controllers.
- *
  *      LOCKING:
  *      None.
  */
 static void ata_dev_xfermask(struct ata_device *dev)
 {
         struct ata_port *ap = dev->ap;
-        struct ata_host_set *hs = ap->host_set;
+        struct ata_host *host = ap->host;
         unsigned long xfer_mask;
-        int i;
 
+        /* controller modes available */
         xfer_mask = ata_pack_xfermask(ap->pio_mask,
                                       ap->mwdma_mask, ap->udma_mask);
 
@@ -3063,34 +3094,31 @@ static void ata_dev_xfermask(struct ata_device *dev)
         if (ap->cbl == ATA_CBL_PATA40)
                 xfer_mask &= ~(0xF8 << ATA_SHIFT_UDMA);
 
-        /* FIXME: Use port-wide xfermask for now */
-        for (i = 0; i < ATA_MAX_DEVICES; i++) {
-                struct ata_device *d = &ap->device[i];
-
-                if (ata_dev_absent(d))
-                        continue;
-
-                if (ata_dev_disabled(d)) {
-                        /* to avoid violating device selection timing */
-                        xfer_mask &= ata_pack_xfermask(d->pio_mask,
-                                                       UINT_MAX, UINT_MAX);
-                        continue;
-                }
+        xfer_mask &= ata_pack_xfermask(dev->pio_mask,
+                                       dev->mwdma_mask, dev->udma_mask);
+        xfer_mask &= ata_id_xfermask(dev->id);
 
-                xfer_mask &= ata_pack_xfermask(d->pio_mask,
-                                               d->mwdma_mask, d->udma_mask);
-                xfer_mask &= ata_id_xfermask(d->id);
-                if (ata_dma_blacklisted(d))
-                        xfer_mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
+        /*
+         *      CFA Advanced TrueIDE timings are not allowed on a shared
+         *      cable
+         */
+        if (ata_dev_pair(dev)) {
+                /* No PIO5 or PIO6 */
+                xfer_mask &= ~(0x03 << (ATA_SHIFT_PIO + 5));
+                /* No MWDMA3 or MWDMA 4 */
+                xfer_mask &= ~(0x03 << (ATA_SHIFT_MWDMA + 3));
         }
 
-        if (ata_dma_blacklisted(dev))
+        if (ata_dma_blacklisted(dev)) {
+                xfer_mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
                 ata_dev_printk(dev, KERN_WARNING,
                                "device is on DMA blacklist, disabling DMA\n");
+        }
 
-        if (hs->flags & ATA_HOST_SIMPLEX) {
-                if (hs->simplex_claimed)
-                        xfer_mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
+        if ((host->flags & ATA_HOST_SIMPLEX) && host->simplex_claimed) {
+                xfer_mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
+                ata_dev_printk(dev, KERN_WARNING, "simplex DMA is claimed by "
+                               "other device, disabling DMA\n");
         }
 
         if (ap->ops->mode_filter)
@@ -3180,7 +3208,7 @@ static unsigned int ata_dev_init_params(struct ata_device *dev,
  *      Unmap all mapped DMA memory associated with this command.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 static void ata_sg_clean(struct ata_queued_cmd *qc)
@@ -3240,7 +3268,7 @@ static void ata_sg_clean(struct ata_queued_cmd *qc)
  *      associated with the current disk command.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  */
 static void ata_fill_sg(struct ata_queued_cmd *qc)
@@ -3292,7 +3320,7 @@ static void ata_fill_sg(struct ata_queued_cmd *qc)
  *      supplied PACKET command.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  *      RETURNS: 0 when ATAPI DMA can be used
  *               nonzero otherwise
@@ -3314,7 +3342,7 @@ int ata_check_atapi_dma(struct ata_queued_cmd *qc)
  *      Prepare ATA taskfile for submission.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 void ata_qc_prep(struct ata_queued_cmd *qc)
 {
@@ -3336,7 +3364,7 @@ void ata_noop_qc_prep(struct ata_queued_cmd *qc) { }
  *      to point to a single memory buffer, @buf of byte length @buflen.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 void ata_sg_init_one(struct ata_queued_cmd *qc, void *buf, unsigned int buflen)
@@ -3367,7 +3395,7 @@ void ata_sg_init_one(struct ata_queued_cmd *qc, void *buf, unsigned int buflen)
  *      elements.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 void ata_sg_init(struct ata_queued_cmd *qc, struct scatterlist *sg,
@@ -3386,7 +3414,7 @@ void ata_sg_init(struct ata_queued_cmd *qc, struct scatterlist *sg,
  *      DMA-map the memory buffer associated with queued_cmd @qc.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  *      RETURNS:
  *      Zero on success, negative on error.
@@ -3455,7 +3483,7 @@ skip_map:
  *      DMA-map the scatter-gather table associated with queued_cmd @qc.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  *      RETURNS:
  *      Zero on success, negative on error.
@@ -3964,7 +3992,7 @@ static inline int ata_hsm_ok_in_wq(struct ata_port *ap, struct ata_queued_cmd *q
  *      Finish @qc which is running on standard HSM.
  *
  *      LOCKING:
- *      If @in_wq is zero, spin_lock_irqsave(host_set lock).
+ *      If @in_wq is zero, spin_lock_irqsave(host lock).
  *      Otherwise, none on entry and grabs host lock.
  */
 static void ata_hsm_qc_complete(struct ata_queued_cmd *qc, int in_wq)
@@ -3976,8 +4004,8 @@ static void ata_hsm_qc_complete(struct ata_queued_cmd *qc, int in_wq)
                 if (in_wq) {
                         spin_lock_irqsave(ap->lock, flags);
 
-                        /* EH might have kicked in while host_set lock
-                         * is released.
+                        /* EH might have kicked in while host lock is
+                         * released.
                          */
                         qc = ata_qc_from_tag(ap, qc->tag);
                         if (qc) {
@@ -4342,7 +4370,7 @@ struct ata_queued_cmd *ata_qc_new_init(struct ata_device *dev)
  *      in case something prevents using it.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 void ata_qc_free(struct ata_queued_cmd *qc)
 {
@@ -4395,7 +4423,7 @@ void __ata_qc_complete(struct ata_queued_cmd *qc)
  *      command has completed, with either an ok or not-ok status.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 void ata_qc_complete(struct ata_queued_cmd *qc)
 {
@@ -4458,7 +4486,7 @@ void ata_qc_complete(struct ata_queued_cmd *qc)
  *      and commands are completed accordingly.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  *      RETURNS:
  *      Number of completed commands on success, -errno otherwise.
@@ -4529,7 +4557,7 @@ static inline int ata_should_dma_map(struct ata_queued_cmd *qc)
  *      writing the taskfile to hardware, starting the command.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 void ata_qc_issue(struct ata_queued_cmd *qc)
 {
@@ -4590,7 +4618,7 @@ err:
  *      May be used as the qc_issue() entry in ata_port_operations.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  *      RETURNS:
  *      Zero on success, AC_ERR_* mask on failure
@@ -4719,7 +4747,7 @@ unsigned int ata_qc_issue_prot(struct ata_queued_cmd *qc)
  *      handled via polling with interrupts disabled (nIEN bit).
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  *      RETURNS:
  *      One if interrupt was handled, zero if not (shared irq).
@@ -4806,14 +4834,14 @@ idle_irq:
 /**
  *      ata_interrupt - Default ATA host interrupt handler
  *      @irq: irq line (unused)
- *      @dev_instance: pointer to our ata_host_set information structure
+ *      @dev_instance: pointer to our ata_host information structure
  *      @regs: unused
  *
  *      Default interrupt handler for PCI IDE devices.  Calls
  *      ata_host_intr() for each port that is not disabled.
  *
  *      LOCKING:
- *      Obtains host_set lock during operation.
+ *      Obtains host lock during operation.
  *
  *      RETURNS:
  *      IRQ_NONE or IRQ_HANDLED.
@@ -4821,18 +4849,18 @@ idle_irq:
 
 irqreturn_t ata_interrupt (int irq, void *dev_instance, struct pt_regs *regs)
 {
-        struct ata_host_set *host_set = dev_instance;
+        struct ata_host *host = dev_instance;
         unsigned int i;
         unsigned int handled = 0;
         unsigned long flags;
 
         /* TODO: make _irqsave conditional on x86 PCI IDE legacy mode */
-        spin_lock_irqsave(&host_set->lock, flags);
+        spin_lock_irqsave(&host->lock, flags);
 
-        for (i = 0; i < host_set->n_ports; i++) {
+        for (i = 0; i < host->n_ports; i++) {
                 struct ata_port *ap;
 
-                ap = host_set->ports[i];
+                ap = host->ports[i];
                 if (ap &&
                     !(ap->flags & ATA_FLAG_DISABLED)) {
                         struct ata_queued_cmd *qc;
@@ -4844,7 +4872,7 @@ irqreturn_t ata_interrupt (int irq, void *dev_instance, struct pt_regs *regs)
                 }
         }
 
-        spin_unlock_irqrestore(&host_set->lock, flags);
+        spin_unlock_irqrestore(&host->lock, flags);
 
         return IRQ_RETVAL(handled);
 }
@@ -5009,15 +5037,15 @@ int ata_flush_cache(struct ata_device *dev)
         return 0;
 }
 
-static int ata_host_set_request_pm(struct ata_host_set *host_set,
-                                   pm_message_t mesg, unsigned int action,
-                                   unsigned int ehi_flags, int wait)
+static int ata_host_request_pm(struct ata_host *host, pm_message_t mesg,
+                               unsigned int action, unsigned int ehi_flags,
+                               int wait)
 {
         unsigned long flags;
         int i, rc;
 
-        for (i = 0; i < host_set->n_ports; i++) {
-                struct ata_port *ap = host_set->ports[i];
+        for (i = 0; i < host->n_ports; i++) {
+                struct ata_port *ap = host->ports[i];
 
                 /* Previous resume operation might still be in
                  * progress.  Wait for PM_PENDING to clear.
@@ -5057,11 +5085,11 @@ static int ata_host_set_request_pm(struct ata_host_set *host_set,
 }
 
 /**
- *      ata_host_set_suspend - suspend host_set
- *      @host_set: host_set to suspend
+ *      ata_host_suspend - suspend host
+ *      @host: host to suspend
  *      @mesg: PM message
  *
- *      Suspend @host_set.  Actual operation is performed by EH.  This
+ *      Suspend @host.  Actual operation is performed by EH.  This
  *      function requests EH to perform PM operations and waits for EH
  *      to finish.
  *
@@ -5071,11 +5099,11 @@ static int ata_host_set_request_pm(struct ata_host_set *host_set,
  *      RETURNS:
  *      0 on success, -errno on failure.
  */
-int ata_host_set_suspend(struct ata_host_set *host_set, pm_message_t mesg)
+int ata_host_suspend(struct ata_host *host, pm_message_t mesg)
 {
         int i, j, rc;
 
-        rc = ata_host_set_request_pm(host_set, mesg, 0, ATA_EHI_QUIET, 1);
+        rc = ata_host_request_pm(host, mesg, 0, ATA_EHI_QUIET, 1);
         if (rc)
                 goto fail;
 
@@ -5083,8 +5111,8 @@ int ata_host_set_suspend(struct ata_host_set *host_set, pm_message_t mesg)
          * This happens if hotplug occurs between completion of device
          * suspension and here.
          */
-        for (i = 0; i < host_set->n_ports; i++) {
-                struct ata_port *ap = host_set->ports[i];
+        for (i = 0; i < host->n_ports; i++) {
+                struct ata_port *ap = host->ports[i];
 
                 for (j = 0; j < ATA_MAX_DEVICES; j++) {
                         struct ata_device *dev = &ap->device[j];
@@ -5099,30 +5127,30 @@ int ata_host_set_suspend(struct ata_host_set *host_set, pm_message_t mesg)
                 }
         }
 
-        host_set->dev->power.power_state = mesg;
+        host->dev->power.power_state = mesg;
         return 0;
 
  fail:
-        ata_host_set_resume(host_set);
+        ata_host_resume(host);
         return rc;
 }
 
 /**
- *      ata_host_set_resume - resume host_set
- *      @host_set: host_set to resume
+ *      ata_host_resume - resume host
+ *      @host: host to resume
  *
- *      Resume @host_set.  Actual operation is performed by EH.  This
+ *      Resume @host.  Actual operation is performed by EH.  This
  *      function requests EH to perform PM operations and returns.
  *      Note that all resume operations are performed parallely.
  *
  *      LOCKING:
  *      Kernel thread context (may sleep).
  */
-void ata_host_set_resume(struct ata_host_set *host_set)
+void ata_host_resume(struct ata_host *host)
 {
-        ata_host_set_request_pm(host_set, PMSG_ON, ATA_EH_SOFTRESET,
-                                ATA_EHI_NO_AUTOPSY | ATA_EHI_QUIET, 0);
-        host_set->dev->power.power_state = PMSG_ON;
+        ata_host_request_pm(host, PMSG_ON, ATA_EH_SOFTRESET,
+                            ATA_EHI_NO_AUTOPSY | ATA_EHI_QUIET, 0);
+        host->dev->power.power_state = PMSG_ON;
 }
 
 /**
@@ -5179,10 +5207,10 @@ void ata_port_stop (struct ata_port *ap)
         ata_pad_free(ap, dev);
 }
 
-void ata_host_stop (struct ata_host_set *host_set)
+void ata_host_stop (struct ata_host *host)
 {
-        if (host_set->mmio_base)
-                iounmap(host_set->mmio_base);
+        if (host->mmio_base)
+                iounmap(host->mmio_base);
 }
 
 /**
@@ -5204,7 +5232,7 @@ void ata_dev_init(struct ata_device *dev)
 
         /* High bits of dev->flags are used to record warm plug
          * requests which occur asynchronously.  Synchronize using
-         * host_set lock.
+         * host lock.
          */
         spin_lock_irqsave(ap->lock, flags);
         dev->flags &= ~ATA_DFLAG_INIT_MASK;
@@ -5218,45 +5246,33 @@ void ata_dev_init(struct ata_device *dev)
 }
 
 /**
- *      ata_host_init - Initialize an ata_port structure
+ *      ata_port_init - Initialize an ata_port structure
  *      @ap: Structure to initialize
- *      @host: associated SCSI mid-layer structure
- *      @host_set: Collection of hosts to which @ap belongs
+ *      @host: Collection of hosts to which @ap belongs
  *      @ent: Probe information provided by low-level driver
  *      @port_no: Port number associated with this ata_port
  *
- *      Initialize a new ata_port structure, and its associated
- *      scsi_host.
+ *      Initialize a new ata_port structure.
  *
  *      LOCKING:
  *      Inherited from caller.
  */
-static void ata_host_init(struct ata_port *ap, struct Scsi_Host *host,
-                          struct ata_host_set *host_set,
-                          const struct ata_probe_ent *ent, unsigned int port_no)
+void ata_port_init(struct ata_port *ap, struct ata_host *host,
+                   const struct ata_probe_ent *ent, unsigned int port_no)
 {
         unsigned int i;
 
-        host->max_id = 16;
-        host->max_lun = 1;
-        host->max_channel = 1;
-        host->unique_id = ata_unique_id++;
-        host->max_cmd_len = 12;
-
-        ap->lock = &host_set->lock;
+        ap->lock = &host->lock;
         ap->flags = ATA_FLAG_DISABLED;
-        ap->id = host->unique_id;
-        ap->host = host;
+        ap->id = ata_unique_id++;
         ap->ctl = ATA_DEVCTL_OBS;
-        ap->host_set = host_set;
+        ap->host = host;
         ap->dev = ent->dev;
         ap->port_no = port_no;
-        ap->hard_port_no =
-                ent->legacy_mode ? ent->hard_port_no : port_no;
         ap->pio_mask = ent->pio_mask;
         ap->mwdma_mask = ent->mwdma_mask;
         ap->udma_mask = ent->udma_mask;
-        ap->flags |= ent->host_flags;
+        ap->flags |= ent->port_flags;
         ap->ops = ent->port_ops;
         ap->hw_sata_spd_limit = UINT_MAX;
         ap->active_tag = ATA_TAG_POISON;
@@ -5298,9 +5314,30 @@ static void ata_host_init(struct ata_port *ap, struct Scsi_Host *host,
 }
 
 /**
- *      ata_host_add - Attach low-level ATA driver to system
+ *      ata_port_init_shost - Initialize SCSI host associated with ATA port
+ *      @ap: ATA port to initialize SCSI host for
+ *      @shost: SCSI host associated with @ap
+ *
+ *      Initialize SCSI host @shost associated with ATA port @ap.
+ *
+ *      LOCKING:
+ *      Inherited from caller.
+ */
+static void ata_port_init_shost(struct ata_port *ap, struct Scsi_Host *shost)
+{
+        ap->scsi_host = shost;
+
+        shost->unique_id = ap->id;
+        shost->max_id = 16;
+        shost->max_lun = 1;
+        shost->max_channel = 1;
+        shost->max_cmd_len = 12;
+}
+
+/**
+ *      ata_port_add - Attach low-level ATA driver to system
  *      @ent: Information provided by low-level driver
- *      @host_set: Collections of ports to which we add
+ *      @host: Collections of ports to which we add
  *      @port_no: Port number associated with this host
  *
  *      Attach low-level ATA driver to system.
@@ -5311,43 +5348,55 @@ static void ata_host_init(struct ata_port *ap, struct Scsi_Host *host,
  *      RETURNS:
  *      New ata_port on success, for NULL on error.
  */
-
-static struct ata_port * ata_host_add(const struct ata_probe_ent *ent,
-                                      struct ata_host_set *host_set,
+static struct ata_port * ata_port_add(const struct ata_probe_ent *ent,
+                                      struct ata_host *host,
                                       unsigned int port_no)
 {
-        struct Scsi_Host *host;
+        struct Scsi_Host *shost;
         struct ata_port *ap;
-        int rc;
 
         DPRINTK("ENTER\n");
 
         if (!ent->port_ops->error_handler &&
-            !(ent->host_flags & (ATA_FLAG_SATA_RESET | ATA_FLAG_SRST))) {
+            !(ent->port_flags & (ATA_FLAG_SATA_RESET | ATA_FLAG_SRST))) {
                 printk(KERN_ERR "ata%u: no reset mechanism available\n",
                        port_no);
                 return NULL;
         }
 
-        host = scsi_host_alloc(ent->sht, sizeof(struct ata_port));
-        if (!host)
+        shost = scsi_host_alloc(ent->sht, sizeof(struct ata_port));
+        if (!shost)
                 return NULL;
 
-        host->transportt = &ata_scsi_transport_template;
-
-        ap = ata_shost_to_port(host);
+        shost->transportt = &ata_scsi_transport_template;
 
-        ata_host_init(ap, host, host_set, ent, port_no);
+        ap = ata_shost_to_port(shost);
 
-        rc = ap->ops->port_start(ap);
-        if (rc)
-                goto err_out;
+        ata_port_init(ap, host, ent, port_no);
+        ata_port_init_shost(ap, shost);
 
         return ap;
+}
 
-err_out:
-        scsi_host_put(host);
-        return NULL;
+/**
+ *      ata_sas_host_init - Initialize a host struct
+ *      @host:  host to initialize
+ *      @dev:   device host is attached to
+ *      @flags: host flags
+ *      @ops:   port_ops
+ *
+ *      LOCKING:
+ *      PCI/etc. bus probe sem.
+ *
+ */
+
+void ata_host_init(struct ata_host *host, struct device *dev,
+                   unsigned long flags, const struct ata_port_operations *ops)
+{
+        spin_lock_init(&host->lock);
+        host->dev = dev;
+        host->flags = flags;
+        host->ops = ops;
 }
 
 /**
@@ -5370,78 +5419,106 @@ err_out:
  */
 int ata_device_add(const struct ata_probe_ent *ent)
 {
-        unsigned int count = 0, i;
+        unsigned int i;
         struct device *dev = ent->dev;
-        struct ata_host_set *host_set;
+        struct ata_host *host;
         int rc;
 
         DPRINTK("ENTER\n");
         /* alloc a container for our list of ATA ports (buses) */
-        host_set = kzalloc(sizeof(struct ata_host_set) +
-                           (ent->n_ports * sizeof(void *)), GFP_KERNEL);
-        if (!host_set)
+        host = kzalloc(sizeof(struct ata_host) +
+                       (ent->n_ports * sizeof(void *)), GFP_KERNEL);
+        if (!host)
                 return 0;
-        spin_lock_init(&host_set->lock);
 
-        host_set->dev = dev;
-        host_set->n_ports = ent->n_ports;
-        host_set->irq = ent->irq;
-        host_set->mmio_base = ent->mmio_base;
-        host_set->private_data = ent->private_data;
-        host_set->ops = ent->port_ops;
-        host_set->flags = ent->host_set_flags;
+        ata_host_init(host, dev, ent->_host_flags, ent->port_ops);
+        host->n_ports = ent->n_ports;
+        host->irq = ent->irq;
+        host->irq2 = ent->irq2;
+        host->mmio_base = ent->mmio_base;
+        host->private_data = ent->private_data;
 
         /* register each port bound to this device */
-        for (i = 0; i < ent->n_ports; i++) {
+        for (i = 0; i < host->n_ports; i++) {
                 struct ata_port *ap;
                 unsigned long xfer_mode_mask;
+                int irq_line = ent->irq;
 
-                ap = ata_host_add(ent, host_set, i);
+                ap = ata_port_add(ent, host, i);
                 if (!ap)
                         goto err_out;
 
-                host_set->ports[i] = ap;
+                host->ports[i] = ap;
+
+                /* dummy? */
+                if (ent->dummy_port_mask & (1 << i)) {
+                        ata_port_printk(ap, KERN_INFO, "DUMMY\n");
+                        ap->ops = &ata_dummy_port_ops;
+                        continue;
+                }
+
+                /* start port */
+                rc = ap->ops->port_start(ap);
+                if (rc) {
+                        host->ports[i] = NULL;
+                        scsi_host_put(ap->scsi_host);
+                        goto err_out;
+                }
+
+                /* Report the secondary IRQ for second channel legacy */
+                if (i == 1 && ent->irq2)
+                        irq_line = ent->irq2;
+
                 xfer_mode_mask =(ap->udma_mask << ATA_SHIFT_UDMA) |
                                 (ap->mwdma_mask << ATA_SHIFT_MWDMA) |
                                 (ap->pio_mask << ATA_SHIFT_PIO);
 
                 /* print per-port info to dmesg */
                 ata_port_printk(ap, KERN_INFO, "%cATA max %s cmd 0x%lX "
-                                "ctl 0x%lX bmdma 0x%lX irq %lu\n",
+                                "ctl 0x%lX bmdma 0x%lX irq %d\n",
                                 ap->flags & ATA_FLAG_SATA ? 'S' : 'P',
                                 ata_mode_string(xfer_mode_mask),
                                 ap->ioaddr.cmd_addr,
                                 ap->ioaddr.ctl_addr,
                                 ap->ioaddr.bmdma_addr,
-                                ent->irq);
+                                irq_line);
 
                 ata_chk_status(ap);
-                host_set->ops->irq_clear(ap);
+                host->ops->irq_clear(ap);
                 ata_eh_freeze_port(ap); /* freeze port before requesting IRQ */
-                count++;
         }
 
-        if (!count)
-                goto err_free_ret;
-
-        /* obtain irq, that is shared between channels */
+        /* obtain irq, that may be shared between channels */
         rc = request_irq(ent->irq, ent->port_ops->irq_handler, ent->irq_flags,
-                         DRV_NAME, host_set);
+                         DRV_NAME, host);
         if (rc) {
                 dev_printk(KERN_ERR, dev, "irq %lu request failed: %d\n",
                            ent->irq, rc);
                 goto err_out;
         }
 
+        /* do we have a second IRQ for the other channel, eg legacy mode */
+        if (ent->irq2) {
+                /* We will get weird core code crashes later if this is true
+                   so trap it now */
+                BUG_ON(ent->irq == ent->irq2);
+
+                rc = request_irq(ent->irq2, ent->port_ops->irq_handler, ent->irq_flags,
+                         DRV_NAME, host);
+                if (rc) {
+                        dev_printk(KERN_ERR, dev, "irq %lu request failed: %d\n",
+                                   ent->irq2, rc);
+                        goto err_out_free_irq;
+                }
+        }
+
         /* perform each probe synchronously */
         DPRINTK("probe begin\n");
-        for (i = 0; i < count; i++) {
-                struct ata_port *ap;
+        for (i = 0; i < host->n_ports; i++) {
+                struct ata_port *ap = host->ports[i];
                 u32 scontrol;
                 int rc;
 
-                ap = host_set->ports[i];
-
                 /* init sata_spd_limit to the current value */
                 if (sata_scr_read(ap, SCR_CONTROL, &scontrol) == 0) {
                         int spd = (scontrol >> 4) & 0xf;
@@ -5449,7 +5526,7 @@ int ata_device_add(const struct ata_probe_ent *ent)
                 }
                 ap->sata_spd_limit = ap->hw_sata_spd_limit;
 
-                rc = scsi_add_host(ap->host, dev);
+                rc = scsi_add_host(ap->scsi_host, dev);
                 if (rc) {
                         ata_port_printk(ap, KERN_ERR, "scsi_add_host failed\n");
                         /* FIXME: do something useful here */
@@ -5497,27 +5574,29 @@ int ata_device_add(const struct ata_probe_ent *ent)
 
         /* probes are done, now scan each port's disk(s) */
         DPRINTK("host probe begin\n");
-        for (i = 0; i < count; i++) {
-                struct ata_port *ap = host_set->ports[i];
+        for (i = 0; i < host->n_ports; i++) {
+                struct ata_port *ap = host->ports[i];
 
                 ata_scsi_scan_host(ap);
         }
 
-        dev_set_drvdata(dev, host_set);
+        dev_set_drvdata(dev, host);
 
         VPRINTK("EXIT, returning %u\n", ent->n_ports);
         return ent->n_ports; /* success */
 
+err_out_free_irq:
+        free_irq(ent->irq, host);
 err_out:
-        for (i = 0; i < count; i++) {
-                struct ata_port *ap = host_set->ports[i];
+        for (i = 0; i < host->n_ports; i++) {
+                struct ata_port *ap = host->ports[i];
                 if (ap) {
                         ap->ops->port_stop(ap);
-                        scsi_host_put(ap->host);
+                        scsi_host_put(ap->scsi_host);
                 }
         }
-err_free_ret:
-        kfree(host_set);
+
+        kfree(host);
         VPRINTK("EXIT, returning 0\n");
         return 0;
 }
@@ -5577,12 +5656,12 @@ void ata_port_detach(struct ata_port *ap)
 
  skip_eh:
         /* remove the associated SCSI host */
-        scsi_remove_host(ap->host);
+        scsi_remove_host(ap->scsi_host);
 }
 
 /**
- *      ata_host_set_remove - PCI layer callback for device removal
- *      @host_set: ATA host set that was removed
+ *      ata_host_remove - PCI layer callback for device removal
+ *      @host: ATA host set that was removed
  *
  *      Unregister all objects associated with this host set. Free those
  *      objects.
@@ -5591,36 +5670,39 @@ void ata_port_detach(struct ata_port *ap)
  *      Inherited from calling layer (may sleep).
  */
 
-void ata_host_set_remove(struct ata_host_set *host_set)
+void ata_host_remove(struct ata_host *host)
 {
         unsigned int i;
 
-        for (i = 0; i < host_set->n_ports; i++)
-                ata_port_detach(host_set->ports[i]);
+        for (i = 0; i < host->n_ports; i++)
+                ata_port_detach(host->ports[i]);
 
-        free_irq(host_set->irq, host_set);
+        free_irq(host->irq, host);
+        if (host->irq2)
+                free_irq(host->irq2, host);
 
-        for (i = 0; i < host_set->n_ports; i++) {
-                struct ata_port *ap = host_set->ports[i];
+        for (i = 0; i < host->n_ports; i++) {
+                struct ata_port *ap = host->ports[i];
 
-                ata_scsi_release(ap->host);
+                ata_scsi_release(ap->scsi_host);
 
                 if ((ap->flags & ATA_FLAG_NO_LEGACY) == 0) {
                         struct ata_ioports *ioaddr = &ap->ioaddr;
 
-                        if (ioaddr->cmd_addr == 0x1f0)
-                                release_region(0x1f0, 8);
-                        else if (ioaddr->cmd_addr == 0x170)
-                                release_region(0x170, 8);
+                        /* FIXME: Add -ac IDE pci mods to remove these special cases */
+                        if (ioaddr->cmd_addr == ATA_PRIMARY_CMD)
+                                release_region(ATA_PRIMARY_CMD, 8);
+                        else if (ioaddr->cmd_addr == ATA_SECONDARY_CMD)
+                                release_region(ATA_SECONDARY_CMD, 8);
                 }
 
-                scsi_host_put(ap->host);
+                scsi_host_put(ap->scsi_host);
         }
 
-        if (host_set->ops->host_stop)
-                host_set->ops->host_stop(host_set);
+        if (host->ops->host_stop)
+                host->ops->host_stop(host);
 
-        kfree(host_set);
+        kfree(host);
 }
 
 /**
@@ -5637,9 +5719,9 @@ void ata_host_set_remove(struct ata_host_set *host_set)
  *      One.
  */
 
-int ata_scsi_release(struct Scsi_Host *host)
+int ata_scsi_release(struct Scsi_Host *shost)
 {
-        struct ata_port *ap = ata_shost_to_port(host);
+        struct ata_port *ap = ata_shost_to_port(shost);
 
         DPRINTK("ENTER\n");
 
@@ -5650,6 +5732,31 @@ int ata_scsi_release(struct Scsi_Host *host)
         return 1;
 }
 
+struct ata_probe_ent *
+ata_probe_ent_alloc(struct device *dev, const struct ata_port_info *port)
+{
+        struct ata_probe_ent *probe_ent;
+
+        probe_ent = kzalloc(sizeof(*probe_ent), GFP_KERNEL);
+        if (!probe_ent) {
+                printk(KERN_ERR DRV_NAME "(%s): out of memory\n",
+                       kobject_name(&(dev->kobj)));
+                return NULL;
+        }
+
+        INIT_LIST_HEAD(&probe_ent->node);
+        probe_ent->dev = dev;
+
+        probe_ent->sht = port->sht;
+        probe_ent->port_flags = port->flags;
+        probe_ent->pio_mask = port->pio_mask;
+        probe_ent->mwdma_mask = port->mwdma_mask;
+        probe_ent->udma_mask = port->udma_mask;
+        probe_ent->port_ops = port->port_ops;
+
+        return probe_ent;
+}
+
 /**
  *      ata_std_ports - initialize ioaddr with standard port offsets.
  *      @ioaddr: IO address structure to be initialized
@@ -5679,11 +5786,11 @@ void ata_std_ports(struct ata_ioports *ioaddr)
 
 #ifdef CONFIG_PCI
 
-void ata_pci_host_stop (struct ata_host_set *host_set)
+void ata_pci_host_stop (struct ata_host *host)
 {
-        struct pci_dev *pdev = to_pci_dev(host_set->dev);
+        struct pci_dev *pdev = to_pci_dev(host->dev);
 
-        pci_iounmap(pdev, host_set->mmio_base);
+        pci_iounmap(pdev, host->mmio_base);
 }
 
 /**
@@ -5703,12 +5810,9 @@ void ata_pci_host_stop (struct ata_host_set *host_set)
 void ata_pci_remove_one (struct pci_dev *pdev)
 {
         struct device *dev = pci_dev_to_dev(pdev);
-        struct ata_host_set *host_set = dev_get_drvdata(dev);
-        struct ata_host_set *host_set2 = host_set->next;
+        struct ata_host *host = dev_get_drvdata(dev);
 
-        ata_host_set_remove(host_set);
-        if (host_set2)
-                ata_host_set_remove(host_set2);
+        ata_host_remove(host);
 
         pci_release_regions(pdev);
         pci_disable_device(pdev);
@@ -5749,11 +5853,11 @@ int pci_test_config_bits(struct pci_dev *pdev, const struct pci_bits *bits)
         return (tmp == bits->val) ? 1 : 0;
 }
 
-void ata_pci_device_do_suspend(struct pci_dev *pdev, pm_message_t state)
+void ata_pci_device_do_suspend(struct pci_dev *pdev, pm_message_t mesg)
 {
         pci_save_state(pdev);
 
-        if (state.event == PM_EVENT_SUSPEND) {
+        if (mesg.event == PM_EVENT_SUSPEND) {
                 pci_disable_device(pdev);
                 pci_set_power_state(pdev, PCI_D3hot);
         }
@@ -5767,37 +5871,26 @@ void ata_pci_device_do_resume(struct pci_dev *pdev)
         pci_set_master(pdev);
 }
 
-int ata_pci_device_suspend(struct pci_dev *pdev, pm_message_t state)
+int ata_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
 {
-        struct ata_host_set *host_set = dev_get_drvdata(&pdev->dev);
+        struct ata_host *host = dev_get_drvdata(&pdev->dev);
         int rc = 0;
 
-        rc = ata_host_set_suspend(host_set, state);
+        rc = ata_host_suspend(host, mesg);
         if (rc)
                 return rc;
 
-        if (host_set->next) {
-                rc = ata_host_set_suspend(host_set->next, state);
-                if (rc) {
-                        ata_host_set_resume(host_set);
-                        return rc;
-                }
-        }
-
-        ata_pci_device_do_suspend(pdev, state);
+        ata_pci_device_do_suspend(pdev, mesg);
 
         return 0;
 }
 
 int ata_pci_device_resume(struct pci_dev *pdev)
 {
-        struct ata_host_set *host_set = dev_get_drvdata(&pdev->dev);
+        struct ata_host *host = dev_get_drvdata(&pdev->dev);
 
         ata_pci_device_do_resume(pdev);
-        ata_host_set_resume(host_set);
-        if (host_set->next)
-                ata_host_set_resume(host_set->next);
-
+        ata_host_resume(host);
         return 0;
 }
 #endif /* CONFIG_PCI */
@@ -5897,6 +5990,39 @@ u32 ata_wait_register(void __iomem *reg, u32 mask, u32 val,
 }
 
 /*
+ * Dummy port_ops
+ */
+static void ata_dummy_noret(struct ata_port *ap)        { }
+static int ata_dummy_ret0(struct ata_port *ap)          { return 0; }
+static void ata_dummy_qc_noret(struct ata_queued_cmd *qc) { }
+
+static u8 ata_dummy_check_status(struct ata_port *ap)
+{
+        return ATA_DRDY;
+}
+
+static unsigned int ata_dummy_qc_issue(struct ata_queued_cmd *qc)
+{
+        return AC_ERR_SYSTEM;
+}
+
+const struct ata_port_operations ata_dummy_port_ops = {
+        .port_disable           = ata_port_disable,
+        .check_status           = ata_dummy_check_status,
+        .check_altstatus        = ata_dummy_check_status,
+        .dev_select             = ata_noop_dev_select,
+        .qc_prep                = ata_noop_qc_prep,
+        .qc_issue               = ata_dummy_qc_issue,
+        .freeze                 = ata_dummy_noret,
+        .thaw                   = ata_dummy_noret,
+        .error_handler          = ata_dummy_noret,
+        .post_internal_cmd      = ata_dummy_qc_noret,
+        .irq_clear              = ata_dummy_noret,
+        .port_start             = ata_dummy_ret0,
+        .port_stop              = ata_dummy_noret,
+};
+
+/*
  * libata is essentially a library of internal helper functions for
  * low-level ATA host controller drivers.  As such, the API/ABI is
  * likely to change as new drivers are added and updated.
@@ -5906,11 +6032,13 @@ u32 ata_wait_register(void __iomem *reg, u32 mask, u32 val,
 EXPORT_SYMBOL_GPL(sata_deb_timing_normal);
 EXPORT_SYMBOL_GPL(sata_deb_timing_hotplug);
 EXPORT_SYMBOL_GPL(sata_deb_timing_long);
+EXPORT_SYMBOL_GPL(ata_dummy_port_ops);
 EXPORT_SYMBOL_GPL(ata_std_bios_param);
 EXPORT_SYMBOL_GPL(ata_std_ports);
+EXPORT_SYMBOL_GPL(ata_host_init);
 EXPORT_SYMBOL_GPL(ata_device_add);
 EXPORT_SYMBOL_GPL(ata_port_detach);
-EXPORT_SYMBOL_GPL(ata_host_set_remove);
+EXPORT_SYMBOL_GPL(ata_host_remove);
 EXPORT_SYMBOL_GPL(ata_sg_init);
 EXPORT_SYMBOL_GPL(ata_sg_init_one);
 EXPORT_SYMBOL_GPL(ata_hsm_move);
@@ -5977,8 +6105,8 @@ EXPORT_SYMBOL_GPL(sata_scr_write);
 EXPORT_SYMBOL_GPL(sata_scr_write_flush);
 EXPORT_SYMBOL_GPL(ata_port_online);
 EXPORT_SYMBOL_GPL(ata_port_offline);
-EXPORT_SYMBOL_GPL(ata_host_set_suspend);
-EXPORT_SYMBOL_GPL(ata_host_set_resume);
+EXPORT_SYMBOL_GPL(ata_host_suspend);
+EXPORT_SYMBOL_GPL(ata_host_resume);
 EXPORT_SYMBOL_GPL(ata_id_string);
 EXPORT_SYMBOL_GPL(ata_id_c_string);
 EXPORT_SYMBOL_GPL(ata_scsi_simulate);
diff --git a/drivers/scsi/libata-eh.c b/drivers/ata/libata-eh.c
index 29f59345305d..b1b510493c2d 100644
--- a/drivers/scsi/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -39,7 +39,7 @@
 #include <scsi/scsi_eh.h>
 #include <scsi/scsi_device.h>
 #include <scsi/scsi_cmnd.h>
-#include "scsi_transport_api.h"
+#include "../scsi/scsi_transport_api.h"
 
 #include <linux/libata.h>
 
@@ -200,7 +200,7 @@ void ata_scsi_error(struct Scsi_Host *host)
         /* synchronize with port task */
         ata_port_flush_task(ap);
 
-        /* synchronize with host_set lock and sort out timeouts */
+        /* synchronize with host lock and sort out timeouts */
 
         /* For new EH, all qcs are finished in one of three ways -
          * normal completion, error completion, and SCSI timeout.
@@ -377,7 +377,7 @@ void ata_port_wait_eh(struct ata_port *ap)
         spin_unlock_irqrestore(ap->lock, flags);
 
         /* make sure SCSI EH is complete */
-        if (scsi_host_in_recovery(ap->host)) {
+        if (scsi_host_in_recovery(ap->scsi_host)) {
                 msleep(10);
                 goto retry;
         }
@@ -486,7 +486,7 @@ void ata_eng_timeout(struct ata_port *ap)
  *      other commands are drained.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 void ata_qc_schedule_eh(struct ata_queued_cmd *qc)
 {
@@ -513,14 +513,14 @@ void ata_qc_schedule_eh(struct ata_queued_cmd *qc)
  *      all commands are drained.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 void ata_port_schedule_eh(struct ata_port *ap)
 {
         WARN_ON(!ap->ops->error_handler);
 
         ap->pflags |= ATA_PFLAG_EH_PENDING;
-        scsi_schedule_eh(ap->host);
+        scsi_schedule_eh(ap->scsi_host);
 
         DPRINTK("port EH scheduled\n");
 }
@@ -532,7 +532,7 @@ void ata_port_schedule_eh(struct ata_port *ap)
  *      Abort all active qc's of @ap and schedule EH.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  *      RETURNS:
  *      Number of aborted qc's.
@@ -575,7 +575,7 @@ int ata_port_abort(struct ata_port *ap)
  *      is frozen.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 static void __ata_port_freeze(struct ata_port *ap)
 {
@@ -596,7 +596,7 @@ static void __ata_port_freeze(struct ata_port *ap)
  *      Abort and freeze @ap.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  *      RETURNS:
  *      Number of aborted commands.
diff --git a/drivers/scsi/libata-scsi.c b/drivers/ata/libata-scsi.c
index e92c31d698ff..3986ec8741b4 100644
--- a/drivers/scsi/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -321,7 +321,7 @@ int ata_scsi_ioctl(struct scsi_device *scsidev, int cmd, void __user *arg)
  *      current command.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  *      RETURNS:
  *      Command allocated, or %NULL if none available.
@@ -400,7 +400,7 @@ void ata_dump_status(unsigned id, struct ata_taskfile *tf)
 /**
  *      ata_scsi_device_suspend - suspend ATA device associated with sdev
  *      @sdev: the SCSI device to suspend
- *      @state: target power management state
+ *      @mesg: target power management message
  *
  *      Request suspend EH action on the ATA device associated with
  *      @sdev and wait for the operation to complete.
@@ -411,7 +411,7 @@ void ata_dump_status(unsigned id, struct ata_taskfile *tf)
  *      RETURNS:
  *      0 on success, -errno otherwise.
  */
-int ata_scsi_device_suspend(struct scsi_device *sdev, pm_message_t state)
+int ata_scsi_device_suspend(struct scsi_device *sdev, pm_message_t mesg)
 {
         struct ata_port *ap = ata_shost_to_port(sdev->host);
         struct ata_device *dev = ata_scsi_find_dev(ap, sdev);
@@ -438,7 +438,7 @@ int ata_scsi_device_suspend(struct scsi_device *sdev, pm_message_t state)
 
         /* request suspend */
         action = ATA_EH_SUSPEND;
-        if (state.event != PM_EVENT_SUSPEND)
+        if (mesg.event != PM_EVENT_SUSPEND)
                 action |= ATA_EH_PM_FREEZE;
         ap->eh_info.dev_action[dev->devno] |= action;
         ap->eh_info.flags |= ATA_EHI_QUIET;
@@ -463,7 +463,7 @@ int ata_scsi_device_suspend(struct scsi_device *sdev, pm_message_t state)
         spin_unlock_irqrestore(ap->lock, flags);
  out:
         if (rc == 0)
-                sdev->sdev_gendev.power.power_state = state;
+                sdev->sdev_gendev.power.power_state = mesg;
         return rc;
 }
 
@@ -537,7 +537,7 @@ int ata_scsi_device_resume(struct scsi_device *sdev)
  *      format sense blocks.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 void ata_to_sense_error(unsigned id, u8 drv_stat, u8 drv_err, u8 *sk, u8 *asc,
                         u8 *ascq, int verbose)
@@ -649,7 +649,7 @@ void ata_to_sense_error(unsigned id, u8 drv_stat, u8 drv_err, u8 *sk, u8 *asc,
  *      block. Clear sense key, ASC & ASCQ if there is no error.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 void ata_gen_ata_desc_sense(struct ata_queued_cmd *qc)
 {
@@ -918,7 +918,7 @@ int ata_scsi_change_queue_depth(struct scsi_device *sdev, int queue_depth)
  *      [See SAT revision 5 at www.t10.org]
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  *      RETURNS:
  *      Zero on success, non-zero on error.
@@ -986,7 +986,7 @@ invalid_fld:
  *      FLUSH CACHE EXT.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  *      RETURNS:
  *      Zero on success, non-zero on error.
@@ -1109,7 +1109,7 @@ static void scsi_16_lba_len(const u8 *scsicmd, u64 *plba, u32 *plen)
  *      Converts SCSI VERIFY command to an ATA READ VERIFY command.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  *      RETURNS:
  *      Zero on success, non-zero on error.
@@ -1233,7 +1233,7 @@ nothing_to_do:
  *      %WRITE_16 are currently supported.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  *      RETURNS:
  *      Zero on success, non-zero on error.
@@ -1467,7 +1467,7 @@ static void ata_scsi_qc_complete(struct ata_queued_cmd *qc)
  *      issued to @dev.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  *      RETURNS:
  *      1 if deferring is needed, 0 otherwise.
@@ -1510,7 +1510,7 @@ static int ata_scmd_need_defer(struct ata_device *dev, int is_io)
  *      termination.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  *      RETURNS:
  *      0 on success, SCSI_ML_QUEUE_DEVICE_BUSY if the command
@@ -1589,7 +1589,7 @@ defer:
  *      Maps buffer contained within SCSI command @cmd.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  *      RETURNS:
  *      Length of response buffer.
@@ -1623,7 +1623,7 @@ static unsigned int ata_scsi_rbuf_get(struct scsi_cmnd *cmd, u8 **buf_out)
  *      Unmaps response buffer contained within @cmd.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 static inline void ata_scsi_rbuf_put(struct scsi_cmnd *cmd, u8 *buf)
@@ -1649,7 +1649,7 @@ static inline void ata_scsi_rbuf_put(struct scsi_cmnd *cmd, u8 *buf)
  *      and sense buffer are assumed to be set).
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 void ata_scsi_rbuf_fill(struct ata_scsi_args *args,
@@ -1680,7 +1680,7 @@ void ata_scsi_rbuf_fill(struct ata_scsi_args *args,
  *      with non-VPD INQUIRY command output.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 unsigned int ata_scsiop_inq_std(struct ata_scsi_args *args, u8 *rbuf,
@@ -1736,7 +1736,7 @@ unsigned int ata_scsiop_inq_std(struct ata_scsi_args *args, u8 *rbuf,
  *      Returns list of inquiry VPD pages available.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 unsigned int ata_scsiop_inq_00(struct ata_scsi_args *args, u8 *rbuf,
@@ -1764,7 +1764,7 @@ unsigned int ata_scsiop_inq_00(struct ata_scsi_args *args, u8 *rbuf,
  *      Returns ATA device serial number.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 unsigned int ata_scsiop_inq_80(struct ata_scsi_args *args, u8 *rbuf,
@@ -1797,7 +1797,7 @@ unsigned int ata_scsiop_inq_80(struct ata_scsi_args *args, u8 *rbuf,
  *         name ("ATA     "), model and serial numbers.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 unsigned int ata_scsiop_inq_83(struct ata_scsi_args *args, u8 *rbuf,
@@ -1849,7 +1849,7 @@ unsigned int ata_scsiop_inq_83(struct ata_scsi_args *args, u8 *rbuf,
  *      that the caller should successfully complete this SCSI command.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 unsigned int ata_scsiop_noop(struct ata_scsi_args *args, u8 *rbuf,
@@ -1990,7 +1990,7 @@ static int ata_dev_supports_fua(u16 *id)
  *      descriptor for other device types.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 unsigned int ata_scsiop_mode_sense(struct ata_scsi_args *args, u8 *rbuf,
@@ -2129,7 +2129,7 @@ saving_not_supp:
  *      Simulate READ CAPACITY commands.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 unsigned int ata_scsiop_read_cap(struct ata_scsi_args *args, u8 *rbuf,
@@ -2204,7 +2204,7 @@ unsigned int ata_scsiop_read_cap(struct ata_scsi_args *args, u8 *rbuf,
  *      Simulate REPORT LUNS command.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 unsigned int ata_scsiop_report_luns(struct ata_scsi_args *args, u8 *rbuf,
@@ -2256,7 +2256,7 @@ void ata_scsi_set_sense(struct scsi_cmnd *cmd, u8 sk, u8 asc, u8 ascq)
  *      and the specified additional sense codes.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 void ata_scsi_badcmd(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *), u8 asc, u8 ascq)
@@ -2421,7 +2421,7 @@ static void atapi_qc_complete(struct ata_queued_cmd *qc)
  *      @scsicmd: SCSI CDB associated with this PACKET command
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  *      RETURNS:
  *      Zero on success, non-zero on failure.
@@ -2500,7 +2500,7 @@ static struct ata_device * __ata_scsi_find_dev(struct ata_port *ap,
  *      Determine if commands should be sent to the specified device.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  *      RETURNS:
  *      0 if commands are not allowed / 1 if commands are allowed
@@ -2534,7 +2534,7 @@ static int ata_scsi_dev_enabled(struct ata_device *dev)
  *      SCSI command to be sent.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  *      RETURNS:
  *      Associated ATA device, or %NULL if not found.
@@ -2808,7 +2808,7 @@ static inline int __ata_scsi_queuecmd(struct scsi_cmnd *cmd,
  *      ATA and ATAPI devices appearing as SCSI devices.
  *
  *      LOCKING:
- *      Releases scsi-layer-held lock, and obtains host_set lock.
+ *      Releases scsi-layer-held lock, and obtains host lock.
  *
  *      RETURNS:
  *      Return value from __ata_scsi_queuecmd() if @cmd can be queued,
@@ -2852,7 +2852,7 @@ int ata_scsi_queuecmd(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *))
  *      that can be handled internally.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 void ata_scsi_simulate(struct ata_device *dev, struct scsi_cmnd *cmd,
@@ -2944,7 +2944,7 @@ void ata_scsi_scan_host(struct ata_port *ap)
                 if (!ata_dev_enabled(dev) || dev->sdev)
                         continue;
 
-                sdev = __scsi_add_device(ap->host, 0, i, 0, NULL);
+                sdev = __scsi_add_device(ap->scsi_host, 0, i, 0, NULL);
                 if (!IS_ERR(sdev)) {
                         dev->sdev = sdev;
                         scsi_device_put(sdev);
@@ -2958,11 +2958,11 @@ void ata_scsi_scan_host(struct ata_port *ap)
  *
  *      This function is called from ata_eh_hotplug() and responsible
  *      for taking the SCSI device attached to @dev offline.  This
- *      function is called with host_set lock which protects dev->sdev
+ *      function is called with host lock which protects dev->sdev
  *      against clearing.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  *
  *      RETURNS:
  *      1 if attached SCSI device exists, 0 otherwise.
@@ -2998,16 +2998,16 @@ static void ata_scsi_remove_dev(struct ata_device *dev)
          * be removed if there is __scsi_device_get() interface which
          * increments reference counts regardless of device state.
          */
-        mutex_lock(&ap->host->scan_mutex);
+        mutex_lock(&ap->scsi_host->scan_mutex);
         spin_lock_irqsave(ap->lock, flags);
 
-        /* clearing dev->sdev is protected by host_set lock */
+        /* clearing dev->sdev is protected by host lock */
         sdev = dev->sdev;
         dev->sdev = NULL;
 
         if (sdev) {
                 /* If user initiated unplug races with us, sdev can go
-                 * away underneath us after the host_set lock and
+                 * away underneath us after the host lock and
                  * scan_mutex are released.  Hold onto it.
                  */
                 if (scsi_device_get(sdev) == 0) {
@@ -3024,7 +3024,7 @@ static void ata_scsi_remove_dev(struct ata_device *dev)
         }
 
         spin_unlock_irqrestore(ap->lock, flags);
-        mutex_unlock(&ap->host->scan_mutex);
+        mutex_unlock(&ap->scsi_host->scan_mutex);
 
         if (sdev) {
                 ata_dev_printk(dev, KERN_INFO, "detaching (SCSI %s)\n",
@@ -3171,3 +3171,152 @@ void ata_scsi_dev_rescan(void *data)
                         scsi_rescan_device(&(dev->sdev->sdev_gendev));
         }
 }
+
+/**
+ *      ata_sas_port_alloc - Allocate port for a SAS attached SATA device
+ *      @pdev: PCI device that the scsi device is attached to
+ *      @port_info: Information from low-level host driver
+ *      @shost: SCSI host that the scsi device is attached to
+ *
+ *      LOCKING:
+ *      PCI/etc. bus probe sem.
+ *
+ *      RETURNS:
+ *      ata_port pointer on success / NULL on failure.
+ */
+
+struct ata_port *ata_sas_port_alloc(struct ata_host *host,
+                                    struct ata_port_info *port_info,
+                                    struct Scsi_Host *shost)
+{
+        struct ata_port *ap = kzalloc(sizeof(*ap), GFP_KERNEL);
+        struct ata_probe_ent *ent;
+
+        if (!ap)
+                return NULL;
+
+        ent = ata_probe_ent_alloc(host->dev, port_info);
+        if (!ent) {
+                kfree(ap);
+                return NULL;
+        }
+
+        ata_port_init(ap, host, ent, 0);
+        ap->lock = shost->host_lock;
+        kfree(ent);
+        return ap;
+}
+EXPORT_SYMBOL_GPL(ata_sas_port_alloc);
+
+/**
+ *      ata_sas_port_start - Set port up for dma.
+ *      @ap: Port to initialize
+ *
+ *      Called just after data structures for each port are
+ *      initialized.  Allocates DMA pad.
+ *
+ *      May be used as the port_start() entry in ata_port_operations.
+ *
+ *      LOCKING:
+ *      Inherited from caller.
+ */
+int ata_sas_port_start(struct ata_port *ap)
+{
+        return ata_pad_alloc(ap, ap->dev);
+}
+EXPORT_SYMBOL_GPL(ata_sas_port_start);
+
+/**
+ *      ata_port_stop - Undo ata_sas_port_start()
+ *      @ap: Port to shut down
+ *
+ *      Frees the DMA pad.
+ *
+ *      May be used as the port_stop() entry in ata_port_operations.
+ *
+ *      LOCKING:
+ *      Inherited from caller.
+ */
+
+void ata_sas_port_stop(struct ata_port *ap)
+{
+        ata_pad_free(ap, ap->dev);
+}
+EXPORT_SYMBOL_GPL(ata_sas_port_stop);
+
+/**
+ *      ata_sas_port_init - Initialize a SATA device
+ *      @ap: SATA port to initialize
+ *
+ *      LOCKING:
+ *      PCI/etc. bus probe sem.
+ *
+ *      RETURNS:
+ *      Zero on success, non-zero on error.
+ */
+
+int ata_sas_port_init(struct ata_port *ap)
+{
+        int rc = ap->ops->port_start(ap);
+
+        if (!rc)
+                rc = ata_bus_probe(ap);
+
+        return rc;
+}
+EXPORT_SYMBOL_GPL(ata_sas_port_init);
+
+/**
+ *      ata_sas_port_destroy - Destroy a SATA port allocated by ata_sas_port_alloc
+ *      @ap: SATA port to destroy
+ *
+ */
+
+void ata_sas_port_destroy(struct ata_port *ap)
+{
+        ap->ops->port_stop(ap);
+        kfree(ap);
+}
+EXPORT_SYMBOL_GPL(ata_sas_port_destroy);
+
+/**
+ *      ata_sas_slave_configure - Default slave_config routine for libata devices
+ *      @sdev: SCSI device to configure
+ *      @ap: ATA port to which SCSI device is attached
+ *
+ *      RETURNS:
+ *      Zero.
+ */
+
+int ata_sas_slave_configure(struct scsi_device *sdev, struct ata_port *ap)
+{
+        ata_scsi_sdev_config(sdev);
+        ata_scsi_dev_config(sdev, ap->device);
+        return 0;
+}
+EXPORT_SYMBOL_GPL(ata_sas_slave_configure);
+
+/**
+ *      ata_sas_queuecmd - Issue SCSI cdb to libata-managed device
+ *      @cmd: SCSI command to be sent
+ *      @done: Completion function, called when command is complete
+ *      @ap:    ATA port to which the command is being sent
+ *
+ *      RETURNS:
+ *      Zero.
+ */
+
+int ata_sas_queuecmd(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *),
+                     struct ata_port *ap)
+{
+        ata_scsi_dump_cdb(ap, cmd);
+
+        if (likely(ata_scsi_dev_enabled(ap->device)))
+                __ata_scsi_queuecmd(cmd, done, ap->device);
+        else {
+                cmd->result = (DID_BAD_TARGET << 16);
+                done(cmd);
+        }
+        return 0;
+}
+EXPORT_SYMBOL_GPL(ata_sas_queuecmd);
diff --git a/drivers/scsi/libata-bmdma.c b/drivers/ata/libata-sff.c
index 9ce221f25954..760502859821 100644
--- a/drivers/scsi/libata-bmdma.c
+++ b/drivers/ata/libata-sff.c
@@ -193,7 +193,7 @@ void ata_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
  *      synchronization with interrupt handler / other threads.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 static void ata_exec_command_pio(struct ata_port *ap, const struct ata_taskfile *tf)
@@ -216,7 +216,7 @@ static void ata_exec_command_pio(struct ata_port *ap, const struct ata_taskfile
  *      FIXME: missing write posting for 400nS delay enforcement
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 static void ata_exec_command_mmio(struct ata_port *ap, const struct ata_taskfile *tf)
@@ -237,7 +237,7 @@ static void ata_exec_command_mmio(struct ata_port *ap, const struct ata_taskfile
  *      synchronization with interrupt handler / other threads.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 void ata_exec_command(struct ata_port *ap, const struct ata_taskfile *tf)
 {
@@ -422,7 +422,7 @@ u8 ata_altstatus(struct ata_port *ap)
  *      @qc: Info associated with this ATA transaction.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 static void ata_bmdma_setup_mmio (struct ata_queued_cmd *qc)
@@ -452,7 +452,7 @@ static void ata_bmdma_setup_mmio (struct ata_queued_cmd *qc)
  *      @qc: Info associated with this ATA transaction.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 static void ata_bmdma_start_mmio (struct ata_queued_cmd *qc)
@@ -483,7 +483,7 @@ static void ata_bmdma_start_mmio (struct ata_queued_cmd *qc)
  *      @qc: Info associated with this ATA transaction.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 static void ata_bmdma_setup_pio (struct ata_queued_cmd *qc)
@@ -511,7 +511,7 @@ static void ata_bmdma_setup_pio (struct ata_queued_cmd *qc)
  *      @qc: Info associated with this ATA transaction.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 static void ata_bmdma_start_pio (struct ata_queued_cmd *qc)
@@ -535,7 +535,7 @@ static void ata_bmdma_start_pio (struct ata_queued_cmd *qc)
  *      May be used as the bmdma_start() entry in ata_port_operations.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 void ata_bmdma_start(struct ata_queued_cmd *qc)
 {
@@ -557,7 +557,7 @@ void ata_bmdma_start(struct ata_queued_cmd *qc)
  *      May be used as the bmdma_setup() entry in ata_port_operations.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 void ata_bmdma_setup(struct ata_queued_cmd *qc)
 {
@@ -577,7 +577,7 @@ void ata_bmdma_setup(struct ata_queued_cmd *qc)
  *      May be used as the irq_clear() entry in ata_port_operations.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 void ata_bmdma_irq_clear(struct ata_port *ap)
@@ -605,7 +605,7 @@ void ata_bmdma_irq_clear(struct ata_port *ap)
  *      May be used as the bmdma_status() entry in ata_port_operations.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 u8 ata_bmdma_status(struct ata_port *ap)
@@ -629,7 +629,7 @@ u8 ata_bmdma_status(struct ata_port *ap)
  *      May be used as the bmdma_stop() entry in ata_port_operations.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 void ata_bmdma_stop(struct ata_queued_cmd *qc)
@@ -797,32 +797,6 @@ void ata_bmdma_post_internal_cmd(struct ata_queued_cmd *qc)
 }
 
 #ifdef CONFIG_PCI
-static struct ata_probe_ent *
-ata_probe_ent_alloc(struct device *dev, const struct ata_port_info *port)
-{
-        struct ata_probe_ent *probe_ent;
-
-        probe_ent = kzalloc(sizeof(*probe_ent), GFP_KERNEL);
-        if (!probe_ent) {
-                printk(KERN_ERR DRV_NAME "(%s): out of memory\n",
-                       kobject_name(&(dev->kobj)));
-                return NULL;
-        }
-
-        INIT_LIST_HEAD(&probe_ent->node);
-        probe_ent->dev = dev;
-
-        probe_ent->sht = port->sht;
-        probe_ent->host_flags = port->host_flags;
-        probe_ent->pio_mask = port->pio_mask;
-        probe_ent->mwdma_mask = port->mwdma_mask;
-        probe_ent->udma_mask = port->udma_mask;
-        probe_ent->port_ops = port->port_ops;
-
-        return probe_ent;
-}
-
-
 /**
  *      ata_pci_init_native_mode - Initialize native-mode driver
  *      @pdev:  pci device to be initialized
@@ -864,7 +838,7 @@ ata_pci_init_native_mode(struct pci_dev *pdev, struct ata_port_info **port, int
                 bmdma = pci_resource_start(pdev, 4);
                 if (bmdma) {
                         if (inb(bmdma + 2) & 0x80)
-                                probe_ent->host_set_flags |= ATA_HOST_SIMPLEX;
+                                probe_ent->_host_flags |= ATA_HOST_SIMPLEX;
                         probe_ent->port[p].bmdma_addr = bmdma;
                 }
                 ata_std_ports(&probe_ent->port[p]);
@@ -880,7 +854,7 @@ ata_pci_init_native_mode(struct pci_dev *pdev, struct ata_port_info **port, int
                 if (bmdma) {
                         bmdma += 8;
                         if(inb(bmdma + 2) & 0x80)
-                        probe_ent->host_set_flags |= ATA_HOST_SIMPLEX;
+                                probe_ent->_host_flags |= ATA_HOST_SIMPLEX;
                         probe_ent->port[p].bmdma_addr = bmdma;
                 }
                 ata_std_ports(&probe_ent->port[p]);
@@ -893,44 +867,48 @@ ata_pci_init_native_mode(struct pci_dev *pdev, struct ata_port_info **port, int
 
 
 static struct ata_probe_ent *ata_pci_init_legacy_port(struct pci_dev *pdev,
-                                struct ata_port_info *port, int port_num)
+                                struct ata_port_info **port, int port_mask)
 {
         struct ata_probe_ent *probe_ent;
-        unsigned long bmdma;
+        unsigned long bmdma = pci_resource_start(pdev, 4);
 
-        probe_ent = ata_probe_ent_alloc(pci_dev_to_dev(pdev), port);
+        probe_ent = ata_probe_ent_alloc(pci_dev_to_dev(pdev), port[0]);
         if (!probe_ent)
                 return NULL;
 
-        probe_ent->legacy_mode = 1;
-        probe_ent->n_ports = 1;
-        probe_ent->hard_port_no = port_num;
-        probe_ent->private_data = port->private_data;
-
-        switch(port_num)
-        {
-                case 0:
-                        probe_ent->irq = 14;
-                        probe_ent->port[0].cmd_addr = 0x1f0;
-                        probe_ent->port[0].altstatus_addr =
-                        probe_ent->port[0].ctl_addr = 0x3f6;
-                        break;
-                case 1:
-                        probe_ent->irq = 15;
-                        probe_ent->port[0].cmd_addr = 0x170;
-                        probe_ent->port[0].altstatus_addr =
-                        probe_ent->port[0].ctl_addr = 0x376;
-                        break;
-        }
+        probe_ent->n_ports = 2;
+        probe_ent->private_data = port[0]->private_data;
 
-        bmdma = pci_resource_start(pdev, 4);
-        if (bmdma != 0) {
-                bmdma += 8 * port_num;
-                probe_ent->port[0].bmdma_addr = bmdma;
-                if (inb(bmdma + 2) & 0x80)
-                        probe_ent->host_set_flags |= ATA_HOST_SIMPLEX;
-        }
-        ata_std_ports(&probe_ent->port[0]);
+        if (port_mask & ATA_PORT_PRIMARY) {
+                probe_ent->irq = 14;
+                probe_ent->port[0].cmd_addr = ATA_PRIMARY_CMD;
+                probe_ent->port[0].altstatus_addr =
+                probe_ent->port[0].ctl_addr = ATA_PRIMARY_CTL;
+                if (bmdma) {
+                        probe_ent->port[0].bmdma_addr = bmdma;
+                        if (inb(bmdma + 2) & 0x80)
+                                probe_ent->_host_flags |= ATA_HOST_SIMPLEX;
+                }
+                ata_std_ports(&probe_ent->port[0]);
+        } else
+                probe_ent->dummy_port_mask |= ATA_PORT_PRIMARY;
+
+        if (port_mask & ATA_PORT_SECONDARY) {
+                if (probe_ent->irq)
+                        probe_ent->irq2 = 15;
+                else
+                        probe_ent->irq = 15;
+                probe_ent->port[1].cmd_addr = ATA_SECONDARY_CMD;
+                probe_ent->port[1].altstatus_addr =
+                probe_ent->port[1].ctl_addr = ATA_SECONDARY_CTL;
+                if (bmdma) {
+                        probe_ent->port[1].bmdma_addr = bmdma + 8;
+                        if (inb(bmdma + 10) & 0x80)
+                                probe_ent->_host_flags |= ATA_HOST_SIMPLEX;
+                }
+                ata_std_ports(&probe_ent->port[1]);
+        } else
+                probe_ent->dummy_port_mask |= ATA_PORT_SECONDARY;
 
         return probe_ent;
 }
@@ -950,6 +928,10 @@ static struct ata_probe_ent *ata_pci_init_legacy_port(struct pci_dev *pdev,
  *      regions, sets the dma mask, enables bus master mode, and calls
  *      ata_device_add()
  *
+ *      ASSUMPTION:
+ *      Nobody makes a single channel controller that appears solely as
+ *      the secondary legacy port on PCI.
+ *
  *      LOCKING:
  *      Inherited from PCI layer (may sleep).
  *
@@ -960,7 +942,7 @@ static struct ata_probe_ent *ata_pci_init_legacy_port(struct pci_dev *pdev,
 int ata_pci_init_one (struct pci_dev *pdev, struct ata_port_info **port_info,
                       unsigned int n_ports)
 {
-        struct ata_probe_ent *probe_ent = NULL, *probe_ent2 = NULL;
+        struct ata_probe_ent *probe_ent = NULL;
         struct ata_port_info *port[2];
         u8 tmp8, mask;
         unsigned int legacy_mode = 0;
@@ -975,7 +957,7 @@ int ata_pci_init_one (struct pci_dev *pdev, struct ata_port_info **port_info,
         else
                 port[1] = port[0];
 
-        if ((port[0]->host_flags & ATA_FLAG_NO_LEGACY) == 0
+        if ((port[0]->flags & ATA_FLAG_NO_LEGACY) == 0
             && (pdev->class >> 8) == PCI_CLASS_STORAGE_IDE) {
                 /* TODO: What if one channel is in native mode ... */
                 pci_read_config_byte(pdev, PCI_CLASS_PROG, &tmp8);
@@ -1009,35 +991,34 @@ int ata_pci_init_one (struct pci_dev *pdev, struct ata_port_info **port_info,
                 goto err_out;
         }
 
-        /* FIXME: Should use platform specific mappers for legacy port ranges */
         if (legacy_mode) {
-                if (!request_region(0x1f0, 8, "libata")) {
+                if (!request_region(ATA_PRIMARY_CMD, 8, "libata")) {
                         struct resource *conflict, res;
-                        res.start = 0x1f0;
-                        res.end = 0x1f0 + 8 - 1;
+                        res.start = ATA_PRIMARY_CMD;
+                        res.end = ATA_PRIMARY_CMD + 8 - 1;
                         conflict = ____request_resource(&ioport_resource, &res);
                         if (!strcmp(conflict->name, "libata"))
-                                legacy_mode |= (1 << 0);
+                                legacy_mode |= ATA_PORT_PRIMARY;
                         else {
                                 disable_dev_on_err = 0;
-                                printk(KERN_WARNING "ata: 0x1f0 IDE port busy\n");
+                                printk(KERN_WARNING "ata: 0x%0X IDE port busy\n", ATA_PRIMARY_CMD);
                         }
                 } else
-                        legacy_mode |= (1 << 0);
+                        legacy_mode |= ATA_PORT_PRIMARY;
 
-                if (!request_region(0x170, 8, "libata")) {
+                if (!request_region(ATA_SECONDARY_CMD, 8, "libata")) {
                         struct resource *conflict, res;
-                        res.start = 0x170;
-                        res.end = 0x170 + 8 - 1;
+                        res.start = ATA_SECONDARY_CMD;
+                        res.end = ATA_SECONDARY_CMD + 8 - 1;
                         conflict = ____request_resource(&ioport_resource, &res);
                         if (!strcmp(conflict->name, "libata"))
-                                legacy_mode |= (1 << 1);
+                                legacy_mode |= ATA_PORT_SECONDARY;
                         else {
                                 disable_dev_on_err = 0;
-                                printk(KERN_WARNING "ata: 0x170 IDE port busy\n");
+                                printk(KERN_WARNING "ata: 0x%X IDE port busy\n", ATA_SECONDARY_CMD);
                         }
                 } else
-                        legacy_mode |= (1 << 1);
+                        legacy_mode |= ATA_PORT_SECONDARY;
         }
 
         /* we have legacy mode, but all ports are unavailable */
@@ -1055,17 +1036,14 @@ int ata_pci_init_one (struct pci_dev *pdev, struct ata_port_info **port_info,
                 goto err_out_regions;
 
         if (legacy_mode) {
-                if (legacy_mode & (1 << 0))
-                        probe_ent = ata_pci_init_legacy_port(pdev, port[0], 0);
-                if (legacy_mode & (1 << 1))
-                        probe_ent2 = ata_pci_init_legacy_port(pdev, port[1], 1);
+                probe_ent = ata_pci_init_legacy_port(pdev, port, legacy_mode);
         } else {
                 if (n_ports == 2)
                         probe_ent = ata_pci_init_native_mode(pdev, port, ATA_PORT_PRIMARY | ATA_PORT_SECONDARY);
                 else
                         probe_ent = ata_pci_init_native_mode(pdev, port, ATA_PORT_PRIMARY);
         }
-        if (!probe_ent && !probe_ent2) {
+        if (!probe_ent) {
                 rc = -ENOMEM;
                 goto err_out_regions;
         }
@@ -1073,35 +1051,17 @@ int ata_pci_init_one (struct pci_dev *pdev, struct ata_port_info **port_info,
         pci_set_master(pdev);
 
         /* FIXME: check ata_device_add return */
-        if (legacy_mode) {
-                struct device *dev = &pdev->dev;
-                struct ata_host_set *host_set = NULL;
-
-                if (legacy_mode & (1 << 0)) {
-                        ata_device_add(probe_ent);
-                        host_set = dev_get_drvdata(dev);
-                }
-
-                if (legacy_mode & (1 << 1)) {
-                        ata_device_add(probe_ent2);
-                        if (host_set) {
-                                host_set->next = dev_get_drvdata(dev);
-                                dev_set_drvdata(dev, host_set);
-                        }
-                }
-        } else
-                ata_device_add(probe_ent);
+        ata_device_add(probe_ent);
 
         kfree(probe_ent);
-        kfree(probe_ent2);
 
         return 0;
 
 err_out_regions:
-        if (legacy_mode & (1 << 0))
-                release_region(0x1f0, 8);
-        if (legacy_mode & (1 << 1))
-                release_region(0x170, 8);
+        if (legacy_mode & ATA_PORT_PRIMARY)
+                release_region(ATA_PRIMARY_CMD, 8);
+        if (legacy_mode & ATA_PORT_SECONDARY)
+                release_region(ATA_SECONDARY_CMD, 8);
         pci_release_regions(pdev);
 err_out:
         if (disable_dev_on_err)
diff --git a/drivers/scsi/libata.h b/drivers/ata/libata.h
index c325679d9b54..a5ecb71390a9 100644
--- a/drivers/scsi/libata.h
+++ b/drivers/ata/libata.h
@@ -69,6 +69,10 @@ extern int ata_flush_cache(struct ata_device *dev);
 extern void ata_dev_init(struct ata_device *dev);
 extern int ata_task_ioctl(struct scsi_device *scsidev, void __user *arg);
 extern int ata_cmd_ioctl(struct scsi_device *scsidev, void __user *arg);
+extern void ata_port_init(struct ata_port *ap, struct ata_host *host,
+                          const struct ata_probe_ent *ent, unsigned int port_no);
+extern struct ata_probe_ent *ata_probe_ent_alloc(struct device *dev,
+                                                 const struct ata_port_info *port);
 
 
 /* libata-scsi.c */
@@ -107,6 +111,7 @@ extern void ata_scsi_rbuf_fill(struct ata_scsi_args *args,
                                            u8 *rbuf, unsigned int buflen));
 extern void ata_schedule_scsi_eh(struct Scsi_Host *shost);
 extern void ata_scsi_dev_rescan(void *data);
+extern int ata_bus_probe(struct ata_port *ap);
 
 /* libata-eh.c */
 extern enum scsi_eh_timer_return ata_scsi_timed_out(struct scsi_cmnd *cmd);
diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
new file mode 100644
index 000000000000..8448ee6e0eed
--- /dev/null
+++ b/drivers/ata/pata_ali.c
@@ -0,0 +1,679 @@
+/*
+ * pata_ali.c   - ALI 15x3 PATA for new ATA layer
+ *                        (C) 2005 Red Hat Inc
+ *                        Alan Cox <alan@redhat.com>
+ *
+ * based in part upon
+ * linux/drivers/ide/pci/alim15x3.c             Version 0.17    2003/01/02
+ *
+ *  Copyright (C) 1998-2000 Michel Aubry, Maintainer
+ *  Copyright (C) 1998-2000 Andrzej Krzysztofowicz, Maintainer
+ *  Copyright (C) 1999-2000 CJ, cjtsai@ali.com.tw, Maintainer
+ *
+ *  Copyright (C) 1998-2000 Andre Hedrick (andre@linux-ide.org)
+ *  May be copied or modified under the terms of the GNU General Public License
+ *  Copyright (C) 2002 Alan Cox <alan@redhat.com>
+ *  ALi (now ULi M5228) support by Clear Zhang <Clear.Zhang@ali.com.tw>
+ *
+ *  Documentation
+ *      Chipset documentation available under NDA only
+ *
+ *  TODO/CHECK
+ *      Cannot have ATAPI on both master & slave for rev < c2 (???) but
+ *      otherwise should do atapi DMA.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/dmi.h>
+
+#define DRV_NAME "pata_ali"
+#define DRV_VERSION "0.6.5"
+
+/*
+ *      Cable special cases
+ */
+
+static struct dmi_system_id cable_dmi_table[] = {
+        {
+                .ident = "HP Pavilion N5430",
+                .matches = {
+                        DMI_MATCH(DMI_BOARD_VENDOR, "Hewlett-Packard"),
+                        DMI_MATCH(DMI_BOARD_NAME, "OmniBook N32N-736"),
+                },
+        },
+        { }
+};
+
+static int ali_cable_override(struct pci_dev *pdev)
+{
+        /* Fujitsu P2000 */
+        if (pdev->subsystem_vendor == 0x10CF && pdev->subsystem_device == 0x10AF)
+                return 1;
+        /* Systems by DMI */
+        if (dmi_check_system(cable_dmi_table))
+                return 1;
+        return 0;
+}
+
+/**
+ *      ali_c2_cable_detect     -       cable detection
+ *      @ap: ATA port
+ *
+ *      Perform cable detection for C2 and later revisions
+ */
+
+static int ali_c2_cable_detect(struct ata_port *ap)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u8 ata66;
+
+        /* Certain laptops use short but suitable cables and don't
+           implement the detect logic */
+
+        if (ali_cable_override(pdev))
+                return ATA_CBL_PATA80;
+
+        /* Host view cable detect 0x4A bit 0 primary bit 1 secondary
+           Bit set for 40 pin */
+        pci_read_config_byte(pdev, 0x4A, &ata66);
+        if (ata66 & (1 << ap->port_no))
+                return ATA_CBL_PATA40;
+        else
+                return ATA_CBL_PATA80;
+}
+
+/**
+ *      ali_early_error_handler -       reset for eary chip
+ *      @ap: ATA port
+ *
+ *      Handle the reset callback for the later chips with cable detect
+ */
+
+static int ali_c2_pre_reset(struct ata_port *ap)
+{
+        ap->cbl = ali_c2_cable_detect(ap);
+        return ata_std_prereset(ap);
+}
+
+static void ali_c2_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, ali_c2_pre_reset,
+                               ata_std_softreset, NULL,
+                               ata_std_postreset);
+}
+
+/**
+ *      ali_early_cable_detect  -       cable detection
+ *      @ap: ATA port
+ *
+ *      Perform cable detection for older chipsets. This turns out to be
+ *      rather easy to implement
+ */
+
+static int ali_early_cable_detect(struct ata_port *ap)
+{
+        return ATA_CBL_PATA40;
+}
+
+/**
+ *      ali_early_probe_init    -       reset for early chip
+ *      @ap: ATA port
+ *
+ *      Handle the reset callback for the early (pre cable detect) chips.
+ */
+
+static int ali_early_pre_reset(struct ata_port *ap)
+{
+        ap->cbl = ali_early_cable_detect(ap);
+        return ata_std_prereset(ap);
+}
+
+static void ali_early_error_handler(struct ata_port *ap)
+{
+        return ata_bmdma_drive_eh(ap, ali_early_pre_reset,
+                                     ata_std_softreset, NULL,
+                                     ata_std_postreset);
+}
+
+/**
+ *      ali_20_filter           -       filter for earlier ALI DMA
+ *      @ap: ALi ATA port
+ *      @adev: attached device
+ *
+ *      Ensure that we do not do DMA on CD devices. We may be able to
+ *      fix that later on. Also ensure we do not do UDMA on WDC drives
+ */
+
+static unsigned long ali_20_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask)
+{
+        char model_num[40];
+        /* No DMA on anything but a disk for now */
+        if (adev->class != ATA_DEV_ATA)
+                mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
+        ata_id_string(adev->id, model_num, ATA_ID_PROD_OFS, sizeof(model_num));
+        if (strstr(model_num, "WDC"))
+                return mask &= ~ATA_MASK_UDMA;
+        return ata_pci_default_filter(ap, adev, mask);
+}
+
+/**
+ *      ali_fifo_control        -       FIFO manager
+ *      @ap: ALi channel to control
+ *      @adev: device for FIFO control
+ *      @on: 0 for off 1 for on
+ *
+ *      Enable or disable the FIFO on a given device. Because of the way the
+ *      ALi FIFO works it provides a boost on ATA disk but can be confused by
+ *      ATAPI and we must therefore manage it.
+ */
+
+static void ali_fifo_control(struct ata_port *ap, struct ata_device *adev, int on)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        int pio_fifo = 0x54 + ap->port_no;
+        u8 fifo;
+        int shift = 4 * adev->devno;
+
+        /* ATA - FIFO on set nibble to 0x05, ATAPI - FIFO off, set nibble to
+           0x00. Not all the docs agree but the behaviour we now use is the
+           one stated in the BIOS Programming Guide */
+
+        pci_read_config_byte(pdev, pio_fifo, &fifo);
+        fifo &= ~(0x0F << shift);
+        if (on)
+                fifo |= (on << shift);
+        pci_write_config_byte(pdev, pio_fifo, fifo);
+}
+
+/**
+ *      ali_program_modes       -       load mode registers
+ *      @ap: ALi channel to load
+ *      @adev: Device the timing is for
+ *      @cmd: Command timing
+ *      @data: Data timing
+ *      @ultra: UDMA timing or zero for off
+ *
+ *      Loads the timing registers for cmd/data and disable UDMA if
+ *      ultra is zero. If ultra is set then load and enable the UDMA
+ *      timing but do not touch the command/data timing.
+ */
+
+static void ali_program_modes(struct ata_port *ap, struct ata_device *adev, struct ata_timing *t, u8 ultra)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        int cas = 0x58 + 4 * ap->port_no;       /* Command timing */
+        int cbt = 0x59 + 4 * ap->port_no;       /* Command timing */
+        int drwt = 0x5A + 4 * ap->port_no + adev->devno; /* R/W timing */
+        int udmat = 0x56 + ap->port_no; /* UDMA timing */
+        int shift = 4 * adev->devno;
+        u8 udma;
+
+        if (t != NULL) {
+                t->setup = FIT(t->setup, 1, 8) & 7;
+                t->act8b = FIT(t->act8b, 1, 8) & 7;
+                t->rec8b = FIT(t->rec8b, 1, 16) & 15;
+                t->active = FIT(t->active, 1, 8) & 7;
+                t->recover = FIT(t->recover, 1, 16) & 15;
+
+                pci_write_config_byte(pdev, cas, t->setup);
+                pci_write_config_byte(pdev, cbt, (t->act8b << 4) | t->rec8b);
+                pci_write_config_byte(pdev, drwt, (t->active << 4) | t->recover);
+        }
+
+        /* Set up the UDMA enable */
+        pci_read_config_byte(pdev, udmat, &udma);
+        udma &= ~(0x0F << shift);
+        udma |= ultra << shift;
+        pci_write_config_byte(pdev, udmat, udma);
+}
+
+/**
+ *      ali_set_piomode -       set initial PIO mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Program the ALi registers for PIO mode. FIXME: add timings for
+ *      PIO5.
+ */
+
+static void ali_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct ata_device *pair = ata_dev_pair(adev);
+        struct ata_timing t;
+        unsigned long T =  1000000000 / 33333;  /* PCI clock based */
+
+        ata_timing_compute(adev, adev->pio_mode, &t, T, 1);
+        if (pair) {
+                struct ata_timing p;
+                ata_timing_compute(pair, pair->pio_mode, &p, T, 1);
+                ata_timing_merge(&p, &t, &t, ATA_TIMING_SETUP|ATA_TIMING_8BIT);
+                if (pair->dma_mode) {
+                        ata_timing_compute(pair, pair->dma_mode, &p, T, 1);
+                        ata_timing_merge(&p, &t, &t, ATA_TIMING_SETUP|ATA_TIMING_8BIT);
+                }
+        }
+
+        /* PIO FIFO is only permitted on ATA disk */
+        if (adev->class != ATA_DEV_ATA)
+                ali_fifo_control(ap, adev, 0x00);
+        ali_program_modes(ap, adev, &t, 0);
+        if (adev->class == ATA_DEV_ATA)
+                ali_fifo_control(ap, adev, 0x05);
+
+}
+
+/**
+ *      ali_set_dmamode -       set initial DMA mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      FIXME: MWDMA timings
+ */
+
+static void ali_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        static u8 udma_timing[7] = { 0xC, 0xB, 0xA, 0x9, 0x8, 0xF, 0xD };
+        struct ata_device *pair = ata_dev_pair(adev);
+        struct ata_timing t;
+        unsigned long T =  1000000000 / 33333;  /* PCI clock based */
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+
+        if (adev->class == ATA_DEV_ATA)
+                ali_fifo_control(ap, adev, 0x08);
+
+        if (adev->dma_mode >= XFER_UDMA_0) {
+                ali_program_modes(ap, adev, NULL, udma_timing[adev->dma_mode - XFER_UDMA_0]);
+                if (adev->dma_mode >= XFER_UDMA_3) {
+                        u8 reg4b;
+                        pci_read_config_byte(pdev, 0x4B, &reg4b);
+                        reg4b |= 1;
+                        pci_write_config_byte(pdev, 0x4B, reg4b);
+                }
+        } else {
+                ata_timing_compute(adev, adev->dma_mode, &t, T, 1);
+                if (pair) {
+                        struct ata_timing p;
+                        ata_timing_compute(pair, pair->pio_mode, &p, T, 1);
+                        ata_timing_merge(&p, &t, &t, ATA_TIMING_SETUP|ATA_TIMING_8BIT);
+                        if (pair->dma_mode) {
+                                ata_timing_compute(pair, pair->dma_mode, &p, T, 1);
+                                ata_timing_merge(&p, &t, &t, ATA_TIMING_SETUP|ATA_TIMING_8BIT);
+                        }
+                }
+                ali_program_modes(ap, adev, &t, 0);
+        }
+}
+
+/**
+ *      ali_lock_sectors        -       Keep older devices to 255 sector mode
+ *      @ap: ATA port
+ *      @adev: Device
+ *
+ *      Called during the bus probe for each device that is found. We use
+ *      this call to lock the sector count of the device to 255 or less on
+ *      older ALi controllers. If we didn't do this then large I/O's would
+ *      require LBA48 commands which the older ALi requires are issued by
+ *      slower PIO methods
+ */
+
+static void ali_lock_sectors(struct ata_port *ap, struct ata_device *adev)
+{
+        adev->max_sectors = 255;
+}
+
+static struct scsi_host_template ali_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        /* Keep LBA28 counts so large I/O's don't turn LBA48 and PIO
+           with older controllers. Not locked so will grow on C5 or later */
+        .max_sectors            = 255,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+/*
+ *      Port operations for PIO only ALi
+ */
+
+static struct ata_port_operations ali_early_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = ali_set_piomode,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = ali_early_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/*
+ *      Port operations for DMA capable ALi without cable
+ *      detect
+ */
+static struct ata_port_operations ali_20_port_ops = {
+        .port_disable   = ata_port_disable,
+
+        .set_piomode    = ali_set_piomode,
+        .set_dmamode    = ali_set_dmamode,
+        .mode_filter    = ali_20_filter,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+        .dev_config     = ali_lock_sectors,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = ali_early_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/*
+ *      Port operations for DMA capable ALi with cable detect
+ */
+static struct ata_port_operations ali_c2_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = ali_set_piomode,
+        .set_dmamode    = ali_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+        .dev_config     = ali_lock_sectors,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = ali_c2_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/*
+ *      Port operations for DMA capable ALi with cable detect and LBA48
+ */
+static struct ata_port_operations ali_c5_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = ali_set_piomode,
+        .set_dmamode    = ali_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = ali_c2_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/**
+ *      ali_init_one            -       discovery callback
+ *      @pdev: PCI device ID
+ *      @id: PCI table info
+ *
+ *      An ALi IDE interface has been discovered. Figure out what revision
+ *      and perform configuration work before handing it to the ATA layer
+ */
+
+static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+        static struct ata_port_info info_early = {
+                .sht = &ali_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .port_ops = &ali_early_port_ops
+        };
+        /* Revision 0x20 added DMA */
+        static struct ata_port_info info_20 = {
+                .sht = &ali_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .port_ops = &ali_20_port_ops
+        };
+        /* Revision 0x20 with support logic added UDMA */
+        static struct ata_port_info info_20_udma = {
+                .sht = &ali_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x07,      /* UDMA33 */
+                .port_ops = &ali_20_port_ops
+        };
+        /* Revision 0xC2 adds UDMA66 */
+        static struct ata_port_info info_c2 = {
+                .sht = &ali_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x1f,
+                .port_ops = &ali_c2_port_ops
+        };
+        /* Revision 0xC3 is UDMA100 */
+        static struct ata_port_info info_c3 = {
+                .sht = &ali_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x3f,
+                .port_ops = &ali_c2_port_ops
+        };
+        /* Revision 0xC4 is UDMA133 */
+        static struct ata_port_info info_c4 = {
+                .sht = &ali_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x7f,
+                .port_ops = &ali_c2_port_ops
+        };
+        /* Revision 0xC5 is UDMA133 with LBA48 DMA */
+        static struct ata_port_info info_c5 = {
+                .sht = &ali_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x7f,
+                .port_ops = &ali_c5_port_ops
+        };
+
+        static struct ata_port_info *port_info[2];
+        u8 rev, tmp;
+        struct pci_dev *north, *isa_bridge;
+
+        pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
+
+        /*
+         * The chipset revision selects the driver operations and
+         * mode data.
+         */
+
+        if (rev < 0x20) {
+                port_info[0] = port_info[1] = &info_early;
+        } else if (rev < 0xC2) {
+                /* 1543-E/F, 1543C-C, 1543C-D, 1543C-E */
+                pci_read_config_byte(pdev, 0x4B, &tmp);
+                /* Clear CD-ROM DMA write bit */
+                tmp &= 0x7F;
+                pci_write_config_byte(pdev, 0x4B, tmp);
+                port_info[0] = port_info[1] = &info_20;
+        } else if (rev == 0xC2) {
+                port_info[0] = port_info[1] = &info_c2;
+        } else if (rev == 0xC3) {
+                port_info[0] = port_info[1] = &info_c3;
+        } else if (rev == 0xC4) {
+                port_info[0] = port_info[1] = &info_c4;
+        } else
+                port_info[0] = port_info[1] = &info_c5;
+
+        if (rev >= 0xC2) {
+                /* Enable cable detection logic */
+                pci_read_config_byte(pdev, 0x4B, &tmp);
+                pci_write_config_byte(pdev, 0x4B, tmp | 0x08);
+        }
+
+        north = pci_get_slot(pdev->bus, PCI_DEVFN(0,0));
+        isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
+
+        if (north && north->vendor == PCI_VENDOR_ID_AL) {
+                /* Configure the ALi bridge logic. For non ALi rely on BIOS.
+                   Set the south bridge enable bit */
+                pci_read_config_byte(isa_bridge, 0x79, &tmp);
+                if (rev == 0xC2)
+                        pci_write_config_byte(isa_bridge, 0x79, tmp | 0x04);
+                else if (rev > 0xC2)
+                        pci_write_config_byte(isa_bridge, 0x79, tmp | 0x02);
+        }
+
+        if (rev >= 0x20) {
+                if (rev < 0xC2) {
+                        /* Are we paired with a UDMA capable chip */
+                        pci_read_config_byte(isa_bridge, 0x5E, &tmp);
+                        if ((tmp & 0x1E) == 0x12)
+                                port_info[0] = port_info[1] = &info_20_udma;
+                }
+                /*
+                 * CD_ROM DMA on (0x53 bit 0). Enable this even if we want
+                 * to use PIO. 0x53 bit 1 (rev 20 only) - enable FIFO control
+                 * via 0x54/55.
+                 */
+                pci_read_config_byte(pdev, 0x53, &tmp);
+                if (rev <= 0x20)
+                        tmp &= ~0x02;
+                if (rev == 0xc7)
+                        tmp |= 0x03;
+                else
+                        tmp |= 0x01;    /* CD_ROM enable for DMA */
+                pci_write_config_byte(pdev, 0x53, tmp);
+        }
+
+        pci_dev_put(isa_bridge);
+        pci_dev_put(north);
+
+        ata_pci_clear_simplex(pdev);
+        return ata_pci_init_one(pdev, port_info, 2);
+}
+
+static struct pci_device_id ali[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M5228), },
+        { PCI_DEVICE(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M5229), },
+        { 0, },
+};
+
+static struct pci_driver ali_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = ali,
+        .probe          = ali_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init ali_init(void)
+{
+        return pci_register_driver(&ali_pci_driver);
+}
+
+
+static void __exit ali_exit(void)
+{
+        pci_unregister_driver(&ali_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for ALi PATA");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, ali);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(ali_init);
+module_exit(ali_exit);
diff --git a/drivers/ata/pata_amd.c b/drivers/ata/pata_amd.c
new file mode 100644
index 000000000000..b3f60fdb02d0
--- /dev/null
+++ b/drivers/ata/pata_amd.c
@@ -0,0 +1,707 @@
+/*
+ * pata_amd.c   - AMD PATA for new ATA layer
+ *                        (C) 2005-2006 Red Hat Inc
+ *                        Alan Cox <alan@redhat.com>
+ *
+ *  Based on pata-sil680. Errata information is taken from data sheets
+ *  and the amd74xx.c driver by Vojtech Pavlik. Nvidia SATA devices are
+ *  claimed by sata-nv.c.
+ *
+ *  TODO:
+ *      Variable system clock when/if it makes sense
+ *      Power management on ports
+ *
+ *
+ *  Documentation publically available.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_amd"
+#define DRV_VERSION "0.2.2"
+
+/**
+ *      timing_setup            -       shared timing computation and load
+ *      @ap: ATA port being set up
+ *      @adev: drive being configured
+ *      @offset: port offset
+ *      @speed: target speed
+ *      @clock: clock multiplier (number of times 33MHz for this part)
+ *
+ *      Perform the actual timing set up for Nvidia or AMD PATA devices.
+ *      The actual devices vary so they all call into this helper function
+ *      providing the clock multipler and offset (because AMD and Nvidia put
+ *      the ports at different locations).
+ */
+
+static void timing_setup(struct ata_port *ap, struct ata_device *adev, int offset, int speed, int clock)
+{
+        static const unsigned char amd_cyc2udma[] = {
+                6, 6, 5, 4, 0, 1, 1, 2, 2, 3, 3, 3, 3, 3, 3, 7
+        };
+
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        struct ata_device *peer = ata_dev_pair(adev);
+        int dn = ap->port_no * 2 + adev->devno;
+        struct ata_timing at, apeer;
+        int T, UT;
+        const int amd_clock = 33333;    /* KHz. */
+        u8 t;
+
+        T = 1000000000 / amd_clock;
+        UT = T / min_t(int, max_t(int, clock, 1), 2);
+
+        if (ata_timing_compute(adev, speed, &at, T, UT) < 0) {
+                dev_printk(KERN_ERR, &pdev->dev, "unknown mode %d.\n", speed);
+                return;
+        }
+
+        if (peer) {
+                /* This may be over conservative */
+                if (peer->dma_mode) {
+                        ata_timing_compute(peer, peer->dma_mode, &apeer, T, UT);
+                        ata_timing_merge(&apeer, &at, &at, ATA_TIMING_8BIT);
+                }
+                ata_timing_compute(peer, peer->pio_mode, &apeer, T, UT);
+                ata_timing_merge(&apeer, &at, &at, ATA_TIMING_8BIT);
+        }
+
+        if (speed == XFER_UDMA_5 && amd_clock <= 33333) at.udma = 1;
+        if (speed == XFER_UDMA_6 && amd_clock <= 33333) at.udma = 15;
+
+        /*
+         *      Now do the setup work
+         */
+
+        /* Configure the address set up timing */
+        pci_read_config_byte(pdev, offset + 0x0C, &t);
+        t = (t & ~(3 << ((3 - dn) << 1))) | ((FIT(at.setup, 1, 4) - 1) << ((3 - dn) << 1));
+        pci_write_config_byte(pdev, offset + 0x0C , t);
+
+        /* Configure the 8bit I/O timing */
+        pci_write_config_byte(pdev, offset + 0x0E + (1 - (dn >> 1)),
+                ((FIT(at.act8b, 1, 16) - 1) << 4) | (FIT(at.rec8b, 1, 16) - 1));
+
+        /* Drive timing */
+        pci_write_config_byte(pdev, offset + 0x08 + (3 - dn),
+                ((FIT(at.active, 1, 16) - 1) << 4) | (FIT(at.recover, 1, 16) - 1));
+
+        switch (clock) {
+                case 1:
+                t = at.udma ? (0xc0 | (FIT(at.udma, 2, 5) - 2)) : 0x03;
+                break;
+
+                case 2:
+                t = at.udma ? (0xc0 | amd_cyc2udma[FIT(at.udma, 2, 10)]) : 0x03;
+                break;
+
+                case 3:
+                t = at.udma ? (0xc0 | amd_cyc2udma[FIT(at.udma, 1, 10)]) : 0x03;
+                break;
+
+                case 4:
+                t = at.udma ? (0xc0 | amd_cyc2udma[FIT(at.udma, 1, 15)]) : 0x03;
+                break;
+
+                default:
+                        return;
+        }
+
+        /* UDMA timing */
+        pci_write_config_byte(pdev, offset + 0x10 + (3 - dn), t);
+}
+
+/**
+ *      amd_probe_init          -       cable detection
+ *      @ap: ATA port
+ *
+ *      Perform cable detection. The BIOS stores this in PCI config
+ *      space for us.
+ */
+
+static int amd_pre_reset(struct ata_port *ap)
+{
+        static const u32 bitmask[2] = {0x03, 0xC0};
+        static const struct pci_bits amd_enable_bits[] = {
+                { 0x40, 1, 0x02, 0x02 },
+                { 0x40, 1, 0x01, 0x01 }
+        };
+
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u8 ata66;
+
+        if (!pci_test_config_bits(pdev, &amd_enable_bits[ap->port_no])) {
+                ata_port_disable(ap);
+                printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+                return 0;
+        }
+
+        pci_read_config_byte(pdev, 0x42, &ata66);
+        if (ata66 & bitmask[ap->port_no])
+                ap->cbl = ATA_CBL_PATA80;
+        else
+                ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+
+}
+
+static void amd_error_handler(struct ata_port *ap)
+{
+        return ata_bmdma_drive_eh(ap, amd_pre_reset,
+                                      ata_std_softreset, NULL,
+                                      ata_std_postreset);
+}
+
+static int amd_early_pre_reset(struct ata_port *ap)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        static struct pci_bits amd_enable_bits[] = {
+                { 0x40, 1, 0x02, 0x02 },
+                { 0x40, 1, 0x01, 0x01 }
+        };
+
+        if (!pci_test_config_bits(pdev, &amd_enable_bits[ap->port_no])) {
+                ata_port_disable(ap);
+                printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+                return 0;
+        }
+        /* No host side cable detection */
+        ap->cbl = ATA_CBL_PATA80;
+        return ata_std_prereset(ap);
+
+}
+
+static void amd_early_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, amd_early_pre_reset,
+                               ata_std_softreset, NULL,
+                               ata_std_postreset);
+}
+
+/**
+ *      amd33_set_piomode       -       set initial PIO mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Program the AMD registers for PIO mode.
+ */
+
+static void amd33_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        timing_setup(ap, adev, 0x40, adev->pio_mode, 1);
+}
+
+static void amd66_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        timing_setup(ap, adev, 0x40, adev->pio_mode, 2);
+}
+
+static void amd100_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        timing_setup(ap, adev, 0x40, adev->pio_mode, 3);
+}
+
+static void amd133_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        timing_setup(ap, adev, 0x40, adev->pio_mode, 4);
+}
+
+/**
+ *      amd33_set_dmamode       -       set initial DMA mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Program the MWDMA/UDMA modes for the AMD and Nvidia
+ *      chipset.
+ */
+
+static void amd33_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        timing_setup(ap, adev, 0x40, adev->dma_mode, 1);
+}
+
+static void amd66_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        timing_setup(ap, adev, 0x40, adev->dma_mode, 2);
+}
+
+static void amd100_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        timing_setup(ap, adev, 0x40, adev->dma_mode, 3);
+}
+
+static void amd133_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        timing_setup(ap, adev, 0x40, adev->dma_mode, 4);
+}
+
+
+/**
+ *      nv_probe_init   -       cable detection
+ *      @ap: ATA port
+ *
+ *      Perform cable detection. The BIOS stores this in PCI config
+ *      space for us.
+ */
+
+static int nv_pre_reset(struct ata_port *ap) {
+        static const u8 bitmask[2] = {0x03, 0xC0};
+
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u8 ata66;
+        u16 udma;
+
+        pci_read_config_byte(pdev, 0x52, &ata66);
+        if (ata66 & bitmask[ap->port_no])
+                ap->cbl = ATA_CBL_PATA80;
+        else
+                ap->cbl = ATA_CBL_PATA40;
+
+        /* We now have to double check because the Nvidia boxes BIOS
+           doesn't always set the cable bits but does set mode bits */
+
+        pci_read_config_word(pdev, 0x62 - 2 * ap->port_no, &udma);
+        if ((udma & 0xC4) == 0xC4 || (udma & 0xC400) == 0xC400)
+                ap->cbl = ATA_CBL_PATA80;
+        return ata_std_prereset(ap);
+}
+
+static void nv_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, nv_pre_reset,
+                               ata_std_softreset, NULL,
+                               ata_std_postreset);
+}
+/**
+ *      nv100_set_piomode       -       set initial PIO mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Program the AMD registers for PIO mode.
+ */
+
+static void nv100_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        timing_setup(ap, adev, 0x50, adev->pio_mode, 3);
+}
+
+static void nv133_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        timing_setup(ap, adev, 0x50, adev->pio_mode, 4);
+}
+
+/**
+ *      nv100_set_dmamode       -       set initial DMA mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Program the MWDMA/UDMA modes for the AMD and Nvidia
+ *      chipset.
+ */
+
+static void nv100_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        timing_setup(ap, adev, 0x50, adev->dma_mode, 3);
+}
+
+static void nv133_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        timing_setup(ap, adev, 0x50, adev->dma_mode, 4);
+}
+
+static struct scsi_host_template amd_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations amd33_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = amd33_set_piomode,
+        .set_dmamode    = amd33_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = amd_early_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static struct ata_port_operations amd66_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = amd66_set_piomode,
+        .set_dmamode    = amd66_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = amd_early_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static struct ata_port_operations amd100_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = amd100_set_piomode,
+        .set_dmamode    = amd100_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = amd_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static struct ata_port_operations amd133_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = amd133_set_piomode,
+        .set_dmamode    = amd133_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = amd_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static struct ata_port_operations nv100_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = nv100_set_piomode,
+        .set_dmamode    = nv100_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = nv_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static struct ata_port_operations nv133_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = nv133_set_piomode,
+        .set_dmamode    = nv133_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = nv_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static int amd_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+        static struct ata_port_info info[10] = {
+                {       /* 0: AMD 7401 */
+                        .sht = &amd_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,     /* No SWDMA */
+                        .udma_mask = 0x07,      /* UDMA 33 */
+                        .port_ops = &amd33_port_ops
+                },
+                {       /* 1: Early AMD7409 - no swdma */
+                        .sht = &amd_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .udma_mask = 0x1f,      /* UDMA 66 */
+                        .port_ops = &amd66_port_ops
+                },
+                {       /* 2: AMD 7409, no swdma errata */
+                        .sht = &amd_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .udma_mask = 0x1f,      /* UDMA 66 */
+                        .port_ops = &amd66_port_ops
+                },
+                {       /* 3: AMD 7411 */
+                        .sht = &amd_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .udma_mask = 0x3f,      /* UDMA 100 */
+                        .port_ops = &amd100_port_ops
+                },
+                {       /* 4: AMD 7441 */
+                        .sht = &amd_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .udma_mask = 0x3f,      /* UDMA 100 */
+                        .port_ops = &amd100_port_ops
+                },
+                {       /* 5: AMD 8111*/
+                        .sht = &amd_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .udma_mask = 0x7f,      /* UDMA 133, no swdma */
+                        .port_ops = &amd133_port_ops
+                },
+                {       /* 6: AMD 8111 UDMA 100 (Serenade) */
+                        .sht = &amd_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .udma_mask = 0x3f,      /* UDMA 100, no swdma */
+                        .port_ops = &amd133_port_ops
+                },
+                {       /* 7: Nvidia Nforce */
+                        .sht = &amd_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .udma_mask = 0x3f,      /* UDMA 100 */
+                        .port_ops = &nv100_port_ops
+                },
+                {       /* 8: Nvidia Nforce2 and later */
+                        .sht = &amd_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .udma_mask = 0x7f,      /* UDMA 133, no swdma */
+                        .port_ops = &nv133_port_ops
+                },
+                {       /* 9: AMD CS5536 (Geode companion) */
+                        .sht = &amd_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .udma_mask = 0x3f,      /* UDMA 100 */
+                        .port_ops = &amd100_port_ops
+                }
+        };
+        static struct ata_port_info *port_info[2];
+        static int printed_version;
+        int type = id->driver_data;
+        u8 rev;
+        u8 fifo;
+
+        if (!printed_version++)
+                dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
+
+        pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
+        pci_read_config_byte(pdev, 0x41, &fifo);
+
+        /* Check for AMD7409 without swdma errata and if found adjust type */
+        if (type == 1 && rev > 0x7)
+                type = 2;
+
+        /* Check for AMD7411 */
+        if (type == 3)
+                /* FIFO is broken */
+                pci_write_config_byte(pdev, 0x41, fifo & 0x0F);
+        else
+                pci_write_config_byte(pdev, 0x41, fifo | 0xF0);
+
+        /* Serenade ? */
+        if (type == 5 && pdev->subsystem_vendor == PCI_VENDOR_ID_AMD &&
+                         pdev->subsystem_device == PCI_DEVICE_ID_AMD_SERENADE)
+                type = 6;       /* UDMA 100 only */
+
+        if (type < 3)
+                ata_pci_clear_simplex(pdev);
+
+        /* And fire it up */
+
+        port_info[0] = port_info[1] = &info[type];
+        return ata_pci_init_one(pdev, port_info, 2);
+}
+
+static const struct pci_device_id amd[] = {
+        { PCI_VENDOR_ID_AMD,    PCI_DEVICE_ID_AMD_COBRA_7401,           PCI_ANY_ID, PCI_ANY_ID, 0, 0,  0 },
+        { PCI_VENDOR_ID_AMD,    PCI_DEVICE_ID_AMD_VIPER_7409,           PCI_ANY_ID, PCI_ANY_ID, 0, 0,  1 },
+        { PCI_VENDOR_ID_AMD,    PCI_DEVICE_ID_AMD_VIPER_7411,           PCI_ANY_ID, PCI_ANY_ID, 0, 0,  3 },
+        { PCI_VENDOR_ID_AMD,    PCI_DEVICE_ID_AMD_OPUS_7441,            PCI_ANY_ID, PCI_ANY_ID, 0, 0,  4 },
+        { PCI_VENDOR_ID_AMD,    PCI_DEVICE_ID_AMD_8111_IDE,             PCI_ANY_ID, PCI_ANY_ID, 0, 0,  5 },
+        { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_IDE,        PCI_ANY_ID, PCI_ANY_ID, 0, 0,  7 },
+        { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2_IDE,       PCI_ANY_ID, PCI_ANY_ID, 0, 0,  8 },
+        { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2S_IDE,      PCI_ANY_ID, PCI_ANY_ID, 0, 0,  8 },
+        { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3_IDE,       PCI_ANY_ID, PCI_ANY_ID, 0, 0,  8 },
+        { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_IDE,      PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
+        { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_IDE,  PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
+        { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_IDE,  PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
+        { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_IDE,  PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
+        { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE,  PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
+        { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_IDE,  PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
+        { PCI_VENDOR_ID_AMD,    PCI_DEVICE_ID_AMD_CS5536_IDE,           PCI_ANY_ID, PCI_ANY_ID, 0, 0, 9 },
+        { 0, },
+};
+
+static struct pci_driver amd_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = amd,
+        .probe          = amd_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init amd_init(void)
+{
+        return pci_register_driver(&amd_pci_driver);
+}
+
+static void __exit amd_exit(void)
+{
+        pci_unregister_driver(&amd_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for AMD PATA IDE");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, amd);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(amd_init);
+module_exit(amd_exit);
diff --git a/drivers/ata/pata_artop.c b/drivers/ata/pata_artop.c
new file mode 100644
index 000000000000..d6ef3bf1bac7
--- /dev/null
+++ b/drivers/ata/pata_artop.c
@@ -0,0 +1,518 @@
+/*
+ *    pata_artop.c - ARTOP ATA controller driver
+ *
+ *      (C) 2006 Red Hat <alan@redhat.com>
+ *
+ *    Based in part on drivers/ide/pci/aec62xx.c
+ *      Copyright (C) 1999-2002 Andre Hedrick <andre@linux-ide.org>
+ *      865/865R fixes for Macintosh card version from a patch to the old
+ *              driver by Thibaut VARENE <varenet@parisc-linux.org>
+ *      When setting the PCI latency we must set 0x80 or higher for burst
+ *              performance Alessandro Zummo <alessandro.zummo@towertech.it>
+ *
+ *      TODO
+ *      850 serialization once the core supports it
+ *      Investigate no_dsc on 850R
+ *      Clock detect
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/ata.h>
+
+#define DRV_NAME        "pata_artop"
+#define DRV_VERSION     "0.4.1"
+
+/*
+ *      The ARTOP has 33 Mhz and "over clocked" timing tables. Until we
+ *      get PCI bus speed functionality we leave this as 0. Its a variable
+ *      for when we get the functionality and also for folks wanting to
+ *      test stuff.
+ */
+
+static int clock = 0;
+
+static int artop6210_pre_reset(struct ata_port *ap)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        const struct pci_bits artop_enable_bits[] = {
+                { 0x4AU, 1U, 0x02UL, 0x02UL },  /* port 0 */
+                { 0x4AU, 1U, 0x04UL, 0x04UL },  /* port 1 */
+        };
+
+        if (!pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no])) {
+                ata_port_disable(ap);
+                printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+                return 0;
+        }
+        ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      artop6210_error_handler - Probe specified port on PATA host controller
+ *      @ap: Port to probe
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void artop6210_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, artop6210_pre_reset,
+                                    ata_std_softreset, NULL,
+                                    ata_std_postreset);
+}
+
+/**
+ *      artop6260_pre_reset     -       check for 40/80 pin
+ *      @ap: Port
+ *
+ *      The ARTOP hardware reports the cable detect bits in register 0x49.
+ *      Nothing complicated needed here.
+ */
+
+static int artop6260_pre_reset(struct ata_port *ap)
+{
+        static const struct pci_bits artop_enable_bits[] = {
+                { 0x4AU, 1U, 0x02UL, 0x02UL },  /* port 0 */
+                { 0x4AU, 1U, 0x04UL, 0x04UL },  /* port 1 */
+        };
+
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u8 tmp;
+
+        /* Odd numbered device ids are the units with enable bits (the -R cards) */
+        if (pdev->device % 1 && !pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no])) {
+                ata_port_disable(ap);
+                printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+                return 0;
+        }
+        pci_read_config_byte(pdev, 0x49, &tmp);
+        if (tmp & (1 >> ap->port_no))
+                ap->cbl = ATA_CBL_PATA40;
+        else
+                ap->cbl = ATA_CBL_PATA80;
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      artop6260_error_handler - Probe specified port on PATA host controller
+ *      @ap: Port to probe
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void artop6260_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, artop6260_pre_reset,
+                                    ata_std_softreset, NULL,
+                                    ata_std_postreset);
+}
+
+/**
+ *      artop6210_load_piomode - Load a set of PATA PIO timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device
+ *      @pio: PIO mode
+ *
+ *      Set PIO mode for device, in host controller PCI config space. This
+ *      is used both to set PIO timings in PIO mode and also to set the
+ *      matching PIO clocking for UDMA, as well as the MWDMA timings.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void artop6210_load_piomode(struct ata_port *ap, struct ata_device *adev, unsigned int pio)
+{
+        struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
+        int dn = adev->devno + 2 * ap->port_no;
+        const u16 timing[2][5] = {
+                { 0x0000, 0x000A, 0x0008, 0x0303, 0x0301 },
+                { 0x0700, 0x070A, 0x0708, 0x0403, 0x0401 }
+
+        };
+        /* Load the PIO timing active/recovery bits */
+        pci_write_config_word(pdev, 0x40 + 2 * dn, timing[clock][pio]);
+}
+
+/**
+ *      artop6210_set_piomode - Initialize host controller PATA PIO timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device we are configuring
+ *
+ *      Set PIO mode for device, in host controller PCI config space. For
+ *      ARTOP we must also clear the UDMA bits if we are not doing UDMA. In
+ *      the event UDMA is used the later call to set_dmamode will set the
+ *      bits as required.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void artop6210_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
+        int dn = adev->devno + 2 * ap->port_no;
+        u8 ultra;
+
+        artop6210_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
+
+        /* Clear the UDMA mode bits (set_dmamode will redo this if needed) */
+        pci_read_config_byte(pdev, 0x54, &ultra);
+        ultra &= ~(3 << (2 * dn));
+        pci_write_config_byte(pdev, 0x54, ultra);
+}
+
+/**
+ *      artop6260_load_piomode - Initialize host controller PATA PIO timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device we are configuring
+ *      @pio: PIO mode
+ *
+ *      Set PIO mode for device, in host controller PCI config space. The
+ *      ARTOP6260 and relatives store the timing data differently.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void artop6260_load_piomode (struct ata_port *ap, struct ata_device *adev, unsigned int pio)
+{
+        struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
+        int dn = adev->devno + 2 * ap->port_no;
+        const u8 timing[2][5] = {
+                { 0x00, 0x0A, 0x08, 0x33, 0x31 },
+                { 0x70, 0x7A, 0x78, 0x43, 0x41 }
+
+        };
+        /* Load the PIO timing active/recovery bits */
+        pci_write_config_byte(pdev, 0x40 + dn, timing[clock][pio]);
+}
+
+/**
+ *      artop6260_set_piomode - Initialize host controller PATA PIO timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device we are configuring
+ *
+ *      Set PIO mode for device, in host controller PCI config space. For
+ *      ARTOP we must also clear the UDMA bits if we are not doing UDMA. In
+ *      the event UDMA is used the later call to set_dmamode will set the
+ *      bits as required.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void artop6260_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
+        u8 ultra;
+
+        artop6260_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
+
+        /* Clear the UDMA mode bits (set_dmamode will redo this if needed) */
+        pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra);
+        ultra &= ~(7 << (4  * adev->devno));    /* One nibble per drive */
+        pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra);
+}
+
+/**
+ *      artop6210_set_dmamode - Initialize host controller PATA PIO timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: um
+ *
+ *      Set DMA mode for device, in host controller PCI config space.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void artop6210_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+        unsigned int pio;
+        struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
+        int dn = adev->devno + 2 * ap->port_no;
+        u8 ultra;
+
+        if (adev->dma_mode == XFER_MW_DMA_0)
+                pio = 1;
+        else
+                pio = 4;
+
+        /* Load the PIO timing active/recovery bits */
+        artop6210_load_piomode(ap, adev, pio);
+
+        pci_read_config_byte(pdev, 0x54, &ultra);
+        ultra &= ~(3 << (2 * dn));
+
+        /* Add ultra DMA bits if in UDMA mode */
+        if (adev->dma_mode >= XFER_UDMA_0) {
+                u8 mode = (adev->dma_mode - XFER_UDMA_0) + 1 - clock;
+                if (mode == 0)
+                        mode = 1;
+                ultra |= (mode << (2 * dn));
+        }
+        pci_write_config_byte(pdev, 0x54, ultra);
+}
+
+/**
+ *      artop6260_set_dmamode - Initialize host controller PATA PIO timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device we are configuring
+ *
+ *      Set DMA mode for device, in host controller PCI config space. The
+ *      ARTOP6260 and relatives store the timing data differently.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void artop6260_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+        unsigned int pio        = adev->pio_mode - XFER_PIO_0;
+        struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
+        u8 ultra;
+
+        if (adev->dma_mode == XFER_MW_DMA_0)
+                pio = 1;
+        else
+                pio = 4;
+
+        /* Load the PIO timing active/recovery bits */
+        artop6260_load_piomode(ap, adev, pio);
+
+        /* Add ultra DMA bits if in UDMA mode */
+        pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra);
+        ultra &= ~(7 << (4  * adev->devno));    /* One nibble per drive */
+        if (adev->dma_mode >= XFER_UDMA_0) {
+                u8 mode = adev->dma_mode - XFER_UDMA_0 + 1 - clock;
+                if (mode == 0)
+                        mode = 1;
+                ultra |= (mode << (4 * adev->devno));
+        }
+        pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra);
+}
+
+static struct scsi_host_template artop_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static const struct ata_port_operations artop6210_ops = {
+        .port_disable           = ata_port_disable,
+        .set_piomode            = artop6210_set_piomode,
+        .set_dmamode            = artop6210_set_dmamode,
+        .mode_filter            = ata_pci_default_filter,
+
+        .tf_load                = ata_tf_load,
+        .tf_read                = ata_tf_read,
+        .check_status           = ata_check_status,
+        .exec_command           = ata_exec_command,
+        .dev_select             = ata_std_dev_select,
+
+        .freeze                 = ata_bmdma_freeze,
+        .thaw                   = ata_bmdma_thaw,
+        .error_handler          = artop6210_error_handler,
+        .post_internal_cmd      = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup            = ata_bmdma_setup,
+        .bmdma_start            = ata_bmdma_start,
+        .bmdma_stop             = ata_bmdma_stop,
+        .bmdma_status           = ata_bmdma_status,
+        .qc_prep                = ata_qc_prep,
+        .qc_issue               = ata_qc_issue_prot,
+        .eng_timeout            = ata_eng_timeout,
+        .data_xfer              = ata_pio_data_xfer,
+
+        .irq_handler            = ata_interrupt,
+        .irq_clear              = ata_bmdma_irq_clear,
+
+        .port_start             = ata_port_start,
+        .port_stop              = ata_port_stop,
+        .host_stop              = ata_host_stop,
+};
+
+static const struct ata_port_operations artop6260_ops = {
+        .port_disable           = ata_port_disable,
+        .set_piomode            = artop6260_set_piomode,
+        .set_dmamode            = artop6260_set_dmamode,
+
+        .tf_load                = ata_tf_load,
+        .tf_read                = ata_tf_read,
+        .check_status           = ata_check_status,
+        .exec_command           = ata_exec_command,
+        .dev_select             = ata_std_dev_select,
+
+        .freeze                 = ata_bmdma_freeze,
+        .thaw                   = ata_bmdma_thaw,
+        .error_handler          = artop6260_error_handler,
+        .post_internal_cmd      = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup            = ata_bmdma_setup,
+        .bmdma_start            = ata_bmdma_start,
+        .bmdma_stop             = ata_bmdma_stop,
+        .bmdma_status           = ata_bmdma_status,
+        .qc_prep                = ata_qc_prep,
+        .qc_issue               = ata_qc_issue_prot,
+        .data_xfer              = ata_pio_data_xfer,
+
+        .eng_timeout            = ata_eng_timeout,
+
+        .irq_handler            = ata_interrupt,
+        .irq_clear              = ata_bmdma_irq_clear,
+
+        .port_start             = ata_port_start,
+        .port_stop              = ata_port_stop,
+        .host_stop              = ata_host_stop,
+};
+
+
+/**
+ *      artop_init_one - Register ARTOP ATA PCI device with kernel services
+ *      @pdev: PCI device to register
+ *      @ent: Entry in artop_pci_tbl matching with @pdev
+ *
+ *      Called from kernel PCI layer.
+ *
+ *      LOCKING:
+ *      Inherited from PCI layer (may sleep).
+ *
+ *      RETURNS:
+ *      Zero on success, or -ERRNO value.
+ */
+
+static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
+{
+        static int printed_version;
+        static struct ata_port_info info_6210 = {
+                .sht            = &artop_sht,
+                .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask       = 0x1f, /* pio0-4 */
+                .mwdma_mask     = 0x07, /* mwdma0-2 */
+                .udma_mask      = ATA_UDMA2,
+                .port_ops       = &artop6210_ops,
+        };
+        static struct ata_port_info info_626x = {
+                .sht            = &artop_sht,
+                .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask       = 0x1f, /* pio0-4 */
+                .mwdma_mask     = 0x07, /* mwdma0-2 */
+                .udma_mask      = ATA_UDMA4,
+                .port_ops       = &artop6260_ops,
+        };
+        static struct ata_port_info info_626x_fast = {
+                .sht            = &artop_sht,
+                .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask       = 0x1f, /* pio0-4 */
+                .mwdma_mask     = 0x07, /* mwdma0-2 */
+                .udma_mask      = ATA_UDMA5,
+                .port_ops       = &artop6260_ops,
+        };
+        struct ata_port_info *port_info[2];
+        struct ata_port_info *info;
+        int ports = 2;
+
+        if (!printed_version++)
+                dev_printk(KERN_DEBUG, &pdev->dev,
+                           "version " DRV_VERSION "\n");
+
+        if (id->driver_data == 0) {     /* 6210 variant */
+                info = &info_6210;
+                /* BIOS may have left us in UDMA, clear it before libata probe */
+                pci_write_config_byte(pdev, 0x54, 0);
+                /* For the moment (also lacks dsc) */
+                printk(KERN_WARNING "ARTOP 6210 requires serialize functionality not yet supported by libata.\n");
+                printk(KERN_WARNING "Secondary ATA ports will not be activated.\n");
+                ports = 1;
+        }
+        else if (id->driver_data == 1)  /* 6260 */
+                info = &info_626x;
+        else if (id->driver_data == 2)  { /* 6260 or 6260 + fast */
+                unsigned long io = pci_resource_start(pdev, 4);
+                u8 reg;
+
+                info = &info_626x;
+                if (inb(io) & 0x10)
+                        info = &info_626x_fast;
+                /* Mac systems come up with some registers not set as we
+                   will need them */
+
+                /* Clear reset & test bits */
+                pci_read_config_byte(pdev, 0x49, &reg);
+                pci_write_config_byte(pdev, 0x49, reg & ~ 0x30);
+
+                /* PCI latency must be > 0x80 for burst mode, tweak it
+                 * if required.
+                 */
+                pci_read_config_byte(pdev, PCI_LATENCY_TIMER, &reg);
+                if (reg <= 0x80)
+                        pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x90);
+
+                /* Enable IRQ output and burst mode */
+                pci_read_config_byte(pdev, 0x4a, &reg);
+                pci_write_config_byte(pdev, 0x4a, (reg & ~0x01) | 0x80);
+
+        }
+        port_info[0] = port_info[1] = info;
+        return ata_pci_init_one(pdev, port_info, ports);
+}
+
+static const struct pci_device_id artop_pci_tbl[] = {
+        { 0x1191, 0x0005, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+        { 0x1191, 0x0006, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
+        { 0x1191, 0x0007, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
+        { 0x1191, 0x0008, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
+        { 0x1191, 0x0009, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
+        { }     /* terminate list */
+};
+
+static struct pci_driver artop_pci_driver = {
+        .name                   = DRV_NAME,
+        .id_table               = artop_pci_tbl,
+        .probe                  = artop_init_one,
+        .remove                 = ata_pci_remove_one,
+};
+
+static int __init artop_init(void)
+{
+        return pci_register_driver(&artop_pci_driver);
+}
+
+static void __exit artop_exit(void)
+{
+        pci_unregister_driver(&artop_pci_driver);
+}
+
+
+module_init(artop_init);
+module_exit(artop_exit);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("SCSI low-level driver for ARTOP PATA");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, artop_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+
diff --git a/drivers/ata/pata_atiixp.c b/drivers/ata/pata_atiixp.c
new file mode 100644
index 000000000000..3f78a1e54a75
--- /dev/null
+++ b/drivers/ata/pata_atiixp.c
@@ -0,0 +1,306 @@
+/*
+ * pata_atiixp.c        - ATI PATA for new ATA layer
+ *                        (C) 2005 Red Hat Inc
+ *                        Alan Cox <alan@redhat.com>
+ *
+ * Based on
+ *
+ *  linux/drivers/ide/pci/atiixp.c      Version 0.01-bart2      Feb. 26, 2004
+ *
+ *  Copyright (C) 2003 ATI Inc. <hyu@ati.com>
+ *  Copyright (C) 2004 Bartlomiej Zolnierkiewicz
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_atiixp"
+#define DRV_VERSION "0.4.2"
+
+enum {
+        ATIIXP_IDE_PIO_TIMING   = 0x40,
+        ATIIXP_IDE_MWDMA_TIMING = 0x44,
+        ATIIXP_IDE_PIO_CONTROL  = 0x48,
+        ATIIXP_IDE_PIO_MODE     = 0x4a,
+        ATIIXP_IDE_UDMA_CONTROL = 0x54,
+        ATIIXP_IDE_UDMA_MODE    = 0x56
+};
+
+static int atiixp_pre_reset(struct ata_port *ap)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        static struct pci_bits atiixp_enable_bits[] = {
+                { 0x48, 1, 0x01, 0x00 },
+                { 0x48, 1, 0x08, 0x00 }
+        };
+
+        if (!pci_test_config_bits(pdev, &atiixp_enable_bits[ap->port_no])) {
+                ata_port_disable(ap);
+                printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+                return 0;
+        }
+        ap->cbl = ATA_CBL_PATA80;
+        return ata_std_prereset(ap);
+}
+
+static void atiixp_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, atiixp_pre_reset, ata_std_softreset, NULL,   ata_std_postreset);
+}
+
+/**
+ *      atiixp_set_pio_timing   -       set initial PIO mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Called by both the pio and dma setup functions to set the controller
+ *      timings for PIO transfers. We must load both the mode number and
+ *      timing values into the controller.
+ */
+
+static void atiixp_set_pio_timing(struct ata_port *ap, struct ata_device *adev, int pio)
+{
+        static u8 pio_timings[5] = { 0x5D, 0x47, 0x34, 0x22, 0x20 };
+
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        int dn = 2 * ap->port_no + adev->devno;
+
+        /* Check this is correct - the order is odd in both drivers */
+        int timing_shift = (16 * ap->port_no) + 8 * (adev->devno ^ 1);
+        u16 pio_mode_data, pio_timing_data;
+
+        pci_read_config_word(pdev, ATIIXP_IDE_PIO_MODE, &pio_mode_data);
+        pio_mode_data &= ~(0x7 << (4 * dn));
+        pio_mode_data |= pio << (4 * dn);
+        pci_write_config_word(pdev, ATIIXP_IDE_PIO_MODE, pio_mode_data);
+
+        pci_read_config_word(pdev, ATIIXP_IDE_PIO_TIMING, &pio_timing_data);
+        pio_mode_data &= ~(0xFF << timing_shift);
+        pio_mode_data |= (pio_timings[pio] << timing_shift);
+        pci_write_config_word(pdev, ATIIXP_IDE_PIO_TIMING, pio_timing_data);
+}
+
+/**
+ *      atiixp_set_piomode      -       set initial PIO mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Called to do the PIO mode setup. We use a shared helper for this
+ *      as the DMA setup must also adjust the PIO timing information.
+ */
+
+static void atiixp_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        atiixp_set_pio_timing(ap, adev, adev->pio_mode - XFER_PIO_0);
+}
+
+/**
+ *      atiixp_set_dmamode      -       set initial DMA mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Called to do the DMA mode setup. We use timing tables for most
+ *      modes but must tune an appropriate PIO mode to match.
+ */
+
+static void atiixp_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        static u8 mwdma_timings[5] = { 0x77, 0x21, 0x20 };
+
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        int dma = adev->dma_mode;
+        int dn = 2 * ap->port_no + adev->devno;
+        int wanted_pio;
+
+        if (adev->dma_mode >= XFER_UDMA_0) {
+                u16 udma_mode_data;
+
+                dma -= XFER_UDMA_0;
+
+                pci_read_config_word(pdev, ATIIXP_IDE_UDMA_MODE, &udma_mode_data);
+                udma_mode_data &= ~(0x7 << (4 * dn));
+                udma_mode_data |= dma << (4 * dn);
+                pci_write_config_word(pdev, ATIIXP_IDE_UDMA_MODE, udma_mode_data);
+        } else {
+                u16 mwdma_timing_data;
+                /* Check this is correct - the order is odd in both drivers */
+                int timing_shift = (16 * ap->port_no) + 8 * (adev->devno ^ 1);
+
+                dma -= XFER_MW_DMA_0;
+
+                pci_read_config_word(pdev, ATIIXP_IDE_MWDMA_TIMING, &mwdma_timing_data);
+                mwdma_timing_data &= ~(0xFF << timing_shift);
+                mwdma_timing_data |= (mwdma_timings[dma] << timing_shift);
+                pci_write_config_word(pdev, ATIIXP_IDE_MWDMA_TIMING, mwdma_timing_data);
+        }
+        /*
+         *      We must now look at the PIO mode situation. We may need to
+         *      adjust the PIO mode to keep the timings acceptable
+         */
+         if (adev->dma_mode >= XFER_MW_DMA_2)
+                wanted_pio = 4;
+        else if (adev->dma_mode == XFER_MW_DMA_1)
+                wanted_pio = 3;
+        else if (adev->dma_mode == XFER_MW_DMA_0)
+                wanted_pio = 0;
+        else BUG();
+
+        if (adev->pio_mode != wanted_pio)
+                atiixp_set_pio_timing(ap, adev, wanted_pio);
+}
+
+/**
+ *      atiixp_bmdma_start      -       DMA start callback
+ *      @qc: Command in progress
+ *
+ *      When DMA begins we need to ensure that the UDMA control
+ *      register for the channel is correctly set.
+ */
+
+static void atiixp_bmdma_start(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct ata_device *adev = qc->dev;
+
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        int dn = (2 * ap->port_no) + adev->devno;
+        u16 tmp16;
+
+        pci_read_config_word(pdev, ATIIXP_IDE_UDMA_CONTROL, &tmp16);
+        if (adev->dma_mode >= XFER_UDMA_0)
+                tmp16 |= (1 << dn);
+        else
+                tmp16 &= ~(1 << dn);
+        pci_write_config_word(pdev, ATIIXP_IDE_UDMA_CONTROL, tmp16);
+        ata_bmdma_start(qc);
+}
+
+/**
+ *      atiixp_dma_stop -       DMA stop callback
+ *      @qc: Command in progress
+ *
+ *      DMA has completed. Clear the UDMA flag as the next operations will
+ *      be PIO ones not UDMA data transfer.
+ */
+
+static void atiixp_bmdma_stop(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        int dn = (2 * ap->port_no) + qc->dev->devno;
+        u16 tmp16;
+
+        pci_read_config_word(pdev, ATIIXP_IDE_UDMA_CONTROL, &tmp16);
+        tmp16 &= ~(1 << dn);
+        pci_write_config_word(pdev, ATIIXP_IDE_UDMA_CONTROL, tmp16);
+        ata_bmdma_stop(qc);
+}
+
+static struct scsi_host_template atiixp_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations atiixp_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = atiixp_set_piomode,
+        .set_dmamode    = atiixp_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = atiixp_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = atiixp_bmdma_start,
+        .bmdma_stop     = atiixp_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static int atiixp_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+        static struct ata_port_info info = {
+                .sht = &atiixp_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x06,     /* No MWDMA0 support */
+                .udma_mask = 0x3F,
+                .port_ops = &atiixp_port_ops
+        };
+        static struct ata_port_info *port_info[2] = { &info, &info };
+        return ata_pci_init_one(dev, port_info, 2);
+}
+
+static struct pci_device_id atiixp[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP200_IDE), },
+        { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP300_IDE), },
+        { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP400_IDE), },
+        { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_IDE), },
+        { 0, },
+};
+
+static struct pci_driver atiixp_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = atiixp,
+        .probe          = atiixp_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init atiixp_init(void)
+{
+        return pci_register_driver(&atiixp_pci_driver);
+}
+
+
+static void __exit atiixp_exit(void)
+{
+        pci_unregister_driver(&atiixp_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for ATI IXP200/300/400");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, atiixp);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(atiixp_init);
+module_exit(atiixp_exit);
diff --git a/drivers/ata/pata_cmd64x.c b/drivers/ata/pata_cmd64x.c
new file mode 100644
index 000000000000..abf1bb7bd322
--- /dev/null
+++ b/drivers/ata/pata_cmd64x.c
@@ -0,0 +1,505 @@
+/*
+ * pata_cmd64x.c        - ATI PATA for new ATA layer
+ *                        (C) 2005 Red Hat Inc
+ *                        Alan Cox <alan@redhat.com>
+ *
+ * Based upon
+ * linux/drivers/ide/pci/cmd64x.c               Version 1.30    Sept 10, 2002
+ *
+ * cmd64x.c: Enable interrupts at initialization time on Ultra/PCI machines.
+ *           Note, this driver is not used at all on other systems because
+ *           there the "BIOS" has done all of the following already.
+ *           Due to massive hardware bugs, UltraDMA is only supported
+ *           on the 646U2 and not on the 646U.
+ *
+ * Copyright (C) 1998           Eddie C. Dost  (ecd@skynet.be)
+ * Copyright (C) 1998           David S. Miller (davem@redhat.com)
+ *
+ * Copyright (C) 1999-2002      Andre Hedrick <andre@linux-ide.org>
+ *
+ * TODO
+ *      Testing work
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_cmd64x"
+#define DRV_VERSION "0.2.1"
+
+/*
+ * CMD64x specific registers definition.
+ */
+
+enum {
+        CFR             = 0x50,
+                CFR_INTR_CH0  = 0x02,
+        CNTRL           = 0x51,
+                CNTRL_DIS_RA0 = 0x40,
+                CNTRL_DIS_RA1 = 0x80,
+                CNTRL_ENA_2ND = 0x08,
+        CMDTIM          = 0x52,
+        ARTTIM0         = 0x53,
+        DRWTIM0         = 0x54,
+        ARTTIM1         = 0x55,
+        DRWTIM1         = 0x56,
+        ARTTIM23        = 0x57,
+                ARTTIM23_DIS_RA2  = 0x04,
+                ARTTIM23_DIS_RA3  = 0x08,
+                ARTTIM23_INTR_CH1 = 0x10,
+        ARTTIM2         = 0x57,
+        ARTTIM3         = 0x57,
+        DRWTIM23        = 0x58,
+        DRWTIM2         = 0x58,
+        BRST            = 0x59,
+        DRWTIM3         = 0x5b,
+        BMIDECR0        = 0x70,
+        MRDMODE         = 0x71,
+                MRDMODE_INTR_CH0 = 0x04,
+                MRDMODE_INTR_CH1 = 0x08,
+                MRDMODE_BLK_CH0  = 0x10,
+                MRDMODE_BLK_CH1  = 0x20,
+        BMIDESR0        = 0x72,
+        UDIDETCR0       = 0x73,
+        DTPR0           = 0x74,
+        BMIDECR1        = 0x78,
+        BMIDECSR        = 0x79,
+        BMIDESR1        = 0x7A,
+        UDIDETCR1       = 0x7B,
+        DTPR1           = 0x7C
+};
+
+static int cmd64x_pre_reset(struct ata_port *ap)
+{
+        ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+}
+
+static int cmd648_pre_reset(struct ata_port *ap)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u8 r;
+
+        /* Check cable detect bits */
+        pci_read_config_byte(pdev, BMIDECSR, &r);
+        if (r & (1 << ap->port_no))
+                ap->cbl = ATA_CBL_PATA80;
+        else
+                ap->cbl = ATA_CBL_PATA40;
+
+        return ata_std_prereset(ap);
+}
+
+static void cmd64x_error_handler(struct ata_port *ap)
+{
+        return ata_bmdma_drive_eh(ap, cmd64x_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+static void cmd648_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, cmd648_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      cmd64x_set_piomode      -       set initial PIO mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Called to do the PIO mode setup.
+ */
+
+static void cmd64x_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        struct ata_timing t;
+        const unsigned long T = 1000000 / 33;
+        const u8 setup_data[] = { 0x40, 0x40, 0x40, 0x80, 0x00 };
+
+        u8 reg;
+
+        /* Port layout is not logical so use a table */
+        const u8 arttim_port[2][2] = {
+                { ARTTIM0, ARTTIM1 },
+                { ARTTIM23, ARTTIM23 }
+        };
+        const u8 drwtim_port[2][2] = {
+                { DRWTIM0, DRWTIM1 },
+                { DRWTIM2, DRWTIM3 }
+        };
+
+        int arttim = arttim_port[ap->port_no][adev->devno];
+        int drwtim = drwtim_port[ap->port_no][adev->devno];
+
+
+        if (ata_timing_compute(adev, adev->pio_mode, &t, T, 0) < 0) {
+                printk(KERN_ERR DRV_NAME ": mode computation failed.\n");
+                return;
+        }
+        if (ap->port_no) {
+                /* Slave has shared address setup */
+                struct ata_device *pair = ata_dev_pair(adev);
+
+                if (pair) {
+                        struct ata_timing tp;
+                        ata_timing_compute(pair, pair->pio_mode, &tp, T, 0);
+                        ata_timing_merge(&t, &tp, &t, ATA_TIMING_SETUP);
+                }
+        }
+
+        printk(KERN_DEBUG DRV_NAME ": active %d recovery %d setup %d.\n",
+                t.active, t.recover, t.setup);
+        if (t.recover > 16) {
+                t.active += t.recover - 16;
+                t.recover = 16;
+        }
+        if (t.active > 16)
+                t.active = 16;
+
+        /* Now convert the clocks into values we can actually stuff into
+           the chip */
+
+        if (t.recover > 1)
+                t.recover--;
+        else
+                t.recover = 15;
+
+        if (t.setup > 4)
+                t.setup = 0xC0;
+        else
+                t.setup = setup_data[t.setup];
+
+        t.active &= 0x0F;       /* 0 = 16 */
+
+        /* Load setup timing */
+        pci_read_config_byte(pdev, arttim, &reg);
+        reg &= 0x3F;
+        reg |= t.setup;
+        pci_write_config_byte(pdev, arttim, reg);
+
+        /* Load active/recovery */
+        pci_write_config_byte(pdev, drwtim, (t.active << 4) | t.recover);
+}
+
+/**
+ *      cmd64x_set_dmamode      -       set initial DMA mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Called to do the DMA mode setup.
+ */
+
+static void cmd64x_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        static const u8 udma_data[] = {
+                0x31, 0x21, 0x11, 0x25, 0x15, 0x05
+        };
+        static const u8 mwdma_data[] = {
+                0x30, 0x20, 0x10
+        };
+
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u8 regU, regD;
+
+        int pciU = UDIDETCR0 + 8 * ap->port_no;
+        int pciD = BMIDESR0 + 8 * ap->port_no;
+        int shift = 2 * adev->devno;
+
+        pci_read_config_byte(pdev, pciD, &regD);
+        pci_read_config_byte(pdev, pciU, &regU);
+
+        regD &= ~(0x20 << shift);
+        regU &= ~(0x35 << shift);
+
+        if (adev->dma_mode >= XFER_UDMA_0)
+                regU |= udma_data[adev->dma_mode - XFER_UDMA_0] << shift;
+        else
+                regD |= mwdma_data[adev->dma_mode - XFER_MW_DMA_0] << shift;
+
+        regD |= 0x20 << adev->devno;
+
+        pci_write_config_byte(pdev, pciU, regU);
+        pci_write_config_byte(pdev, pciD, regD);
+}
+
+/**
+ *      cmd648_dma_stop -       DMA stop callback
+ *      @qc: Command in progress
+ *
+ *      DMA has completed.
+ */
+
+static void cmd648_bmdma_stop(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u8 dma_intr;
+        int dma_reg = ap->port_no ? ARTTIM23_INTR_CH1 : CFR_INTR_CH0;
+        int dma_mask = ap->port_no ? ARTTIM2 : CFR;
+
+        ata_bmdma_stop(qc);
+
+        pci_read_config_byte(pdev, dma_reg, &dma_intr);
+        pci_write_config_byte(pdev, dma_reg, dma_intr | dma_mask);
+}
+
+/**
+ *      cmd646r1_dma_stop       -       DMA stop callback
+ *      @qc: Command in progress
+ *
+ *      Stub for now while investigating the r1 quirk in the old driver.
+ */
+
+static void cmd646r1_bmdma_stop(struct ata_queued_cmd *qc)
+{
+        ata_bmdma_stop(qc);
+}
+
+static struct scsi_host_template cmd64x_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations cmd64x_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = cmd64x_set_piomode,
+        .set_dmamode    = cmd64x_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = cmd64x_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static struct ata_port_operations cmd646r1_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = cmd64x_set_piomode,
+        .set_dmamode    = cmd64x_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = cmd64x_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = cmd646r1_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static struct ata_port_operations cmd648_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = cmd64x_set_piomode,
+        .set_dmamode    = cmd64x_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = cmd648_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = cmd648_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+        u32 class_rev;
+
+        static struct ata_port_info cmd_info[6] = {
+                {       /* CMD 643 - no UDMA */
+                        .sht = &cmd64x_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .port_ops = &cmd64x_port_ops
+                },
+                {       /* CMD 646 with broken UDMA */
+                        .sht = &cmd64x_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .port_ops = &cmd64x_port_ops
+                },
+                {       /* CMD 646 with working UDMA */
+                        .sht = &cmd64x_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .udma_mask = ATA_UDMA1,
+                        .port_ops = &cmd64x_port_ops
+                },
+                {       /* CMD 646 rev 1  */
+                        .sht = &cmd64x_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .port_ops = &cmd646r1_port_ops
+                },
+                {       /* CMD 648 */
+                        .sht = &cmd64x_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .udma_mask = ATA_UDMA2,
+                        .port_ops = &cmd648_port_ops
+                },
+                {       /* CMD 649 */
+                        .sht = &cmd64x_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .udma_mask = ATA_UDMA3,
+                        .port_ops = &cmd648_port_ops
+                }
+        };
+        static struct ata_port_info *port_info[2], *info;
+        u8 mrdmode;
+
+        info = &cmd_info[id->driver_data];
+
+        pci_read_config_dword(pdev, PCI_CLASS_REVISION, &class_rev);
+        class_rev &= 0xFF;
+
+        if (id->driver_data == 0)       /* 643 */
+                ata_pci_clear_simplex(pdev);
+
+        if (pdev->device == PCI_DEVICE_ID_CMD_646) {
+                /* Does UDMA work ? */
+                if (class_rev > 4)
+                        info = &cmd_info[2];
+                /* Early rev with other problems ? */
+                else if (class_rev == 1)
+                        info = &cmd_info[3];
+        }
+
+        pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 64);
+        pci_read_config_byte(pdev, MRDMODE, &mrdmode);
+        mrdmode &= ~ 0x30;      /* IRQ set up */
+        mrdmode |= 0x02;        /* Memory read line enable */
+        pci_write_config_byte(pdev, MRDMODE, mrdmode);
+
+        /* Force PIO 0 here.. */
+
+        /* PPC specific fixup copied from old driver */
+#ifdef CONFIG_PPC
+        pci_write_config_byte(pdev, UDIDETCR0, 0xF0);
+#endif
+
+        port_info[0] = port_info[1] = info;
+        return ata_pci_init_one(pdev, port_info, 2);
+}
+
+static struct pci_device_id cmd64x[] = {
+        { PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_CMD_643, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+        { PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_CMD_646, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
+        { PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_CMD_648, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4},
+        { PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_CMD_649, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5},
+        { 0, },
+};
+
+static struct pci_driver cmd64x_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = cmd64x,
+        .probe          = cmd64x_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init cmd64x_init(void)
+{
+        return pci_register_driver(&cmd64x_pci_driver);
+}
+
+
+static void __exit cmd64x_exit(void)
+{
+        pci_unregister_driver(&cmd64x_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for CMD64x series PATA controllers");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, cmd64x);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(cmd64x_init);
+module_exit(cmd64x_exit);
diff --git a/drivers/ata/pata_cs5520.c b/drivers/ata/pata_cs5520.c
new file mode 100644
index 000000000000..792ce4828510
--- /dev/null
+++ b/drivers/ata/pata_cs5520.c
@@ -0,0 +1,336 @@
+/*
+ *      IDE tuning and bus mastering support for the CS5510/CS5520
+ *      chipsets
+ *
+ *      The CS5510/CS5520 are slightly unusual devices. Unlike the
+ *      typical IDE controllers they do bus mastering with the drive in
+ *      PIO mode and smarter silicon.
+ *
+ *      The practical upshot of this is that we must always tune the
+ *      drive for the right PIO mode. We must also ignore all the blacklists
+ *      and the drive bus mastering DMA information. Also to confuse matters
+ *      further we can do DMA on PIO only drives.
+ *
+ *      DMA on the 5510 also requires we disable_hlt() during DMA on early
+ *      revisions.
+ *
+ *      *** This driver is strictly experimental ***
+ *
+ *      (c) Copyright Red Hat Inc 2002
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2, or (at your option) any
+ * later version.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * Documentation:
+ *      Not publically available.
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME        "pata_cs5520"
+#define DRV_VERSION     "0.6.2"
+
+struct pio_clocks
+{
+        int address;
+        int assert;
+        int recovery;
+};
+
+static const struct pio_clocks cs5520_pio_clocks[]={
+        {3, 6, 11},
+        {2, 5, 6},
+        {1, 4, 3},
+        {1, 3, 2},
+        {1, 2, 1}
+};
+
+/**
+ *      cs5520_set_timings      -       program PIO timings
+ *      @ap: ATA port
+ *      @adev: ATA device
+ *
+ *      Program the PIO mode timings for the controller according to the pio
+ *      clocking table.
+ */
+
+static void cs5520_set_timings(struct ata_port *ap, struct ata_device *adev, int pio)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        int slave = adev->devno;
+
+        pio -= XFER_PIO_0;
+
+        /* Channel command timing */
+        pci_write_config_byte(pdev, 0x62 + ap->port_no,
+                                (cs5520_pio_clocks[pio].recovery << 4) |
+                                (cs5520_pio_clocks[pio].assert));
+        /* FIXME: should these use address ? */
+        /* Read command timing */
+        pci_write_config_byte(pdev, 0x64 +  4*ap->port_no + slave,
+                                (cs5520_pio_clocks[pio].recovery << 4) |
+                                (cs5520_pio_clocks[pio].assert));
+        /* Write command timing */
+        pci_write_config_byte(pdev, 0x66 +  4*ap->port_no + slave,
+                                (cs5520_pio_clocks[pio].recovery << 4) |
+                                (cs5520_pio_clocks[pio].assert));
+}
+
+/**
+ *      cs5520_enable_dma       -       turn on DMA bits
+ *
+ *      Turn on the DMA bits for this disk. Needed because the BIOS probably
+ *      has not done the work for us. Belongs in the core SATA code.
+ */
+
+static void cs5520_enable_dma(struct ata_port *ap, struct ata_device *adev)
+{
+        /* Set the DMA enable/disable flag */
+        u8 reg = inb(ap->ioaddr.bmdma_addr + 0x02);
+        reg |= 1<<(adev->devno + 5);
+        outb(reg, ap->ioaddr.bmdma_addr + 0x02);
+}
+
+/**
+ *      cs5520_set_dmamode      -       program DMA timings
+ *      @ap: ATA port
+ *      @adev: ATA device
+ *
+ *      Program the DMA mode timings for the controller according to the pio
+ *      clocking table. Note that this device sets the DMA timings to PIO
+ *      mode values. This may seem bizarre but the 5520 architecture talks
+ *      PIO mode to the disk and DMA mode to the controller so the underlying
+ *      transfers are PIO timed.
+ */
+
+static void cs5520_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        static const int dma_xlate[3] = { XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 };
+        cs5520_set_timings(ap, adev, dma_xlate[adev->dma_mode]);
+        cs5520_enable_dma(ap, adev);
+}
+
+/**
+ *      cs5520_set_piomode      -       program PIO timings
+ *      @ap: ATA port
+ *      @adev: ATA device
+ *
+ *      Program the PIO mode timings for the controller according to the pio
+ *      clocking table. We know pio_mode will equal dma_mode because of the
+ *      CS5520 architecture. At least once we turned DMA on and wrote a
+ *      mode setter.
+ */
+
+static void cs5520_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        cs5520_set_timings(ap, adev, adev->pio_mode);
+}
+
+
+static int cs5520_pre_reset(struct ata_port *ap)
+{
+        ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+}
+
+static void cs5520_error_handler(struct ata_port *ap)
+{
+        return ata_bmdma_drive_eh(ap, cs5520_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+static struct scsi_host_template cs5520_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations cs5520_port_ops = {
+        .port_disable           = ata_port_disable,
+        .set_piomode            = cs5520_set_piomode,
+        .set_dmamode            = cs5520_set_dmamode,
+
+        .tf_load                = ata_tf_load,
+        .tf_read                = ata_tf_read,
+        .check_status           = ata_check_status,
+        .exec_command           = ata_exec_command,
+        .dev_select             = ata_std_dev_select,
+
+        .freeze                 = ata_bmdma_freeze,
+        .thaw                   = ata_bmdma_thaw,
+        .error_handler          = cs5520_error_handler,
+        .post_internal_cmd      = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup            = ata_bmdma_setup,
+        .bmdma_start            = ata_bmdma_start,
+        .bmdma_stop             = ata_bmdma_stop,
+        .bmdma_status           = ata_bmdma_status,
+        .qc_prep                = ata_qc_prep,
+        .qc_issue               = ata_qc_issue_prot,
+        .data_xfer              = ata_pio_data_xfer,
+
+        .eng_timeout            = ata_eng_timeout,
+
+        .irq_handler            = ata_interrupt,
+        .irq_clear              = ata_bmdma_irq_clear,
+
+        .port_start             = ata_port_start,
+        .port_stop              = ata_port_stop,
+        .host_stop              = ata_host_stop,
+};
+
+static int __devinit cs5520_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+        u8 pcicfg;
+        static struct ata_probe_ent probe[2];
+        int ports = 0;
+
+        /* IDE port enable bits */
+        pci_read_config_byte(dev, 0x60, &pcicfg);
+
+        /* Check if the ATA ports are enabled */
+        if ((pcicfg & 3) == 0)
+                return -ENODEV;
+
+        if ((pcicfg & 0x40) == 0) {
+                printk(KERN_WARNING DRV_NAME ": DMA mode disabled. Enabling.\n");
+                pci_write_config_byte(dev, 0x60, pcicfg | 0x40);
+        }
+
+        /* Perform set up for DMA */
+        if (pci_enable_device_bars(dev, 1<<2)) {
+                printk(KERN_ERR DRV_NAME ": unable to configure BAR2.\n");
+                return -ENODEV;
+        }
+        pci_set_master(dev);
+        if (pci_set_dma_mask(dev, DMA_32BIT_MASK)) {
+                printk(KERN_ERR DRV_NAME ": unable to configure DMA mask.\n");
+                return -ENODEV;
+        }
+        if (pci_set_consistent_dma_mask(dev, DMA_32BIT_MASK)) {
+                printk(KERN_ERR DRV_NAME ": unable to configure consistent DMA mask.\n");
+                return -ENODEV;
+        }
+
+        /* We have to do our own plumbing as the PCI setup for this
+           chipset is non-standard so we can't punt to the libata code */
+
+        INIT_LIST_HEAD(&probe[0].node);
+        probe[0].dev = pci_dev_to_dev(dev);
+        probe[0].port_ops = &cs5520_port_ops;
+        probe[0].sht = &cs5520_sht;
+        probe[0].pio_mask = 0x1F;
+        probe[0].mwdma_mask = id->driver_data;
+        probe[0].irq = 14;
+        probe[0].irq_flags = 0;
+        probe[0].port_flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST;
+        probe[0].n_ports = 1;
+        probe[0].port[0].cmd_addr = 0x1F0;
+        probe[0].port[0].ctl_addr = 0x3F6;
+        probe[0].port[0].altstatus_addr = 0x3F6;
+        probe[0].port[0].bmdma_addr = pci_resource_start(dev, 2);
+
+        /* The secondary lurks at different addresses but is otherwise
+           the same beastie */
+
+        probe[1] = probe[0];
+        INIT_LIST_HEAD(&probe[1].node);
+        probe[1].irq = 15;
+        probe[1].port[0].cmd_addr = 0x170;
+        probe[1].port[0].ctl_addr = 0x376;
+        probe[1].port[0].altstatus_addr = 0x376;
+        probe[1].port[0].bmdma_addr = pci_resource_start(dev, 2) + 8;
+
+        /* Let libata fill in the port details */
+        ata_std_ports(&probe[0].port[0]);
+        ata_std_ports(&probe[1].port[0]);
+
+        /* Now add the ports that are active */
+        if (pcicfg & 1)
+                ports += ata_device_add(&probe[0]);
+        if (pcicfg & 2)
+                ports += ata_device_add(&probe[1]);
+        if (ports)
+                return 0;
+        return -ENODEV;
+}
+
+/**
+ *      cs5520_remove_one       -       device unload
+ *      @pdev: PCI device being removed
+ *
+ *      Handle an unplug/unload event for a PCI device. Unload the
+ *      PCI driver but do not use the default handler as we manage
+ *      resources ourself and *MUST NOT* disable the device as it has
+ *      other functions.
+ */
+
+static void __devexit cs5520_remove_one(struct pci_dev *pdev)
+{
+        struct device *dev = pci_dev_to_dev(pdev);
+        struct ata_host *host = dev_get_drvdata(dev);
+
+        ata_host_remove(host);
+        dev_set_drvdata(dev, NULL);
+}
+
+/* For now keep DMA off. We can set it for all but A rev CS5510 once the
+   core ATA code can handle it */
+
+static struct pci_device_id pata_cs5520[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5510), },
+        { PCI_DEVICE(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5520), },
+        { 0, },
+};
+
+static struct pci_driver cs5520_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = pata_cs5520,
+        .probe          = cs5520_init_one,
+        .remove         = cs5520_remove_one
+};
+
+
+static int __init cs5520_init(void)
+{
+        return pci_register_driver(&cs5520_pci_driver);
+}
+
+static void __exit cs5520_exit(void)
+{
+        pci_unregister_driver(&cs5520_pci_driver);
+}
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for Cyrix CS5510/5520");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, pata_cs5520);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(cs5520_init);
+module_exit(cs5520_exit);
+
diff --git a/drivers/ata/pata_cs5530.c b/drivers/ata/pata_cs5530.c
new file mode 100644
index 000000000000..f3d8a3bc1e78
--- /dev/null
+++ b/drivers/ata/pata_cs5530.c
@@ -0,0 +1,387 @@
+/*
+ * pata-cs5530.c        - CS5530 PATA for new ATA layer
+ *                        (C) 2005 Red Hat Inc
+ *                        Alan Cox <alan@redhat.com>
+ *
+ * based upon cs5530.c by Mark Lord.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ * Loosely based on the piix & svwks drivers.
+ *
+ * Documentation:
+ *      Available from AMD web site.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/dmi.h>
+
+#define DRV_NAME        "pata_cs5530"
+#define DRV_VERSION     "0.6"
+
+/**
+ *      cs5530_set_piomode              -       PIO setup
+ *      @ap: ATA interface
+ *      @adev: device on the interface
+ *
+ *      Set our PIO requirements. This is fairly simple on the CS5530
+ *      chips.
+ */
+
+static void cs5530_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        static const unsigned int cs5530_pio_timings[2][5] = {
+                {0x00009172, 0x00012171, 0x00020080, 0x00032010, 0x00040010},
+                {0xd1329172, 0x71212171, 0x30200080, 0x20102010, 0x00100010}
+        };
+        unsigned long base = ( ap->ioaddr.bmdma_addr & ~0x0F) + 0x20 + 0x10 * ap->port_no;
+        u32 tuning;
+        int format;
+
+        /* Find out which table to use */
+        tuning = inl(base + 0x04);
+        format = (tuning & 0x80000000UL) ? 1 : 0;
+
+        /* Now load the right timing register */
+        if (adev->devno)
+                base += 0x08;
+
+        outl(cs5530_pio_timings[format][adev->pio_mode - XFER_PIO_0], base);
+}
+
+/**
+ *      cs5530_set_dmamode              -       DMA timing setup
+ *      @ap: ATA interface
+ *      @adev: Device being configured
+ *
+ *      We cannot mix MWDMA and UDMA without reloading timings each switch
+ *      master to slave. We track the last DMA setup in order to minimise
+ *      reloads.
+ */
+
+static void cs5530_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        unsigned long base = ( ap->ioaddr.bmdma_addr & ~0x0F) + 0x20 + 0x10 * ap->port_no;
+        u32 tuning, timing = 0;
+        u8 reg;
+
+        /* Find out which table to use */
+        tuning = inl(base + 0x04);
+
+        switch(adev->dma_mode) {
+                case XFER_UDMA_0:
+                        timing  = 0x00921250;break;
+                case XFER_UDMA_1:
+                        timing  = 0x00911140;break;
+                case XFER_UDMA_2:
+                        timing  = 0x00911030;break;
+                case XFER_MW_DMA_0:
+                        timing  = 0x00077771;break;
+                case XFER_MW_DMA_1:
+                        timing  = 0x00012121;break;
+                case XFER_MW_DMA_2:
+                        timing  = 0x00002020;break;
+                default:
+                        BUG();
+        }
+        /* Merge in the PIO format bit */
+        timing |= (tuning & 0x80000000UL);
+        if (adev->devno == 0) /* Master */
+                outl(timing, base + 0x04);
+        else {
+                if (timing & 0x00100000)
+                        tuning |= 0x00100000;   /* UDMA for both */
+                else
+                        tuning &= ~0x00100000;  /* MWDMA for both */
+                outl(tuning, base + 0x04);
+                outl(timing, base + 0x0C);
+        }
+
+        /* Set the DMA capable bit in the BMDMA area */
+        reg = inb(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
+        reg |= (1 << (5 + adev->devno));
+        outb(reg, ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
+
+        /* Remember the last DMA setup we did */
+
+        ap->private_data = adev;
+}
+
+/**
+ *      cs5530_qc_issue_prot    -       command issue
+ *      @qc: command pending
+ *
+ *      Called when the libata layer is about to issue a command. We wrap
+ *      this interface so that we can load the correct ATA timings if
+ *      neccessary.  Specifically we have a problem that there is only
+ *      one MWDMA/UDMA bit.
+ */
+
+static unsigned int cs5530_qc_issue_prot(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct ata_device *adev = qc->dev;
+        struct ata_device *prev = ap->private_data;
+
+        /* See if the DMA settings could be wrong */
+        if (adev->dma_mode != 0 && adev != prev && prev != NULL) {
+                /* Maybe, but do the channels match MWDMA/UDMA ? */
+                if ((adev->dma_mode >= XFER_UDMA_0 && prev->dma_mode < XFER_UDMA_0) ||
+                    (adev->dma_mode < XFER_UDMA_0 && prev->dma_mode >= XFER_UDMA_0))
+                        /* Switch the mode bits */
+                        cs5530_set_dmamode(ap, adev);
+        }
+
+        return ata_qc_issue_prot(qc);
+}
+
+static int cs5530_pre_reset(struct ata_port *ap)
+{
+        ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+}
+
+static void cs5530_error_handler(struct ata_port *ap)
+{
+        return ata_bmdma_drive_eh(ap, cs5530_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+
+static struct scsi_host_template cs5530_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations cs5530_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = cs5530_set_piomode,
+        .set_dmamode    = cs5530_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = cs5530_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = cs5530_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static struct dmi_system_id palmax_dmi_table[] = {
+        {
+                .ident = "Palmax PD1100",
+                .matches = {
+                        DMI_MATCH(DMI_SYS_VENDOR, "Cyrix"),
+                        DMI_MATCH(DMI_PRODUCT_NAME, "Caddis"),
+                },
+        },
+        { }
+};
+
+static int cs5530_is_palmax(void)
+{
+        if (dmi_check_system(palmax_dmi_table)) {
+                printk(KERN_INFO "Palmax PD1100: Disabling DMA on docking port.\n");
+                return 1;
+        }
+        return 0;
+}
+
+/**
+ *      cs5530_init_one         -       Initialise a CS5530
+ *      @dev: PCI device
+ *      @id: Entry in match table
+ *
+ *      Install a driver for the newly found CS5530 companion chip. Most of
+ *      this is just housekeeping. We have to set the chip up correctly and
+ *      turn off various bits of emulation magic.
+ */
+
+static int cs5530_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+        int compiler_warning_pointless_fix;
+        struct pci_dev *master_0 = NULL, *cs5530_0 = NULL;
+        static struct ata_port_info info = {
+                .sht = &cs5530_sht,
+                .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x07,
+                .port_ops = &cs5530_port_ops
+        };
+        /* The docking connector doesn't do UDMA, and it seems not MWDMA */
+        static struct ata_port_info info_palmax_secondary = {
+                .sht = &cs5530_sht,
+                .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .port_ops = &cs5530_port_ops
+        };
+        static struct ata_port_info *port_info[2] = { &info, &info };
+
+        dev = NULL;
+        while ((dev = pci_get_device(PCI_VENDOR_ID_CYRIX, PCI_ANY_ID, dev)) != NULL) {
+                switch (dev->device) {
+                        case PCI_DEVICE_ID_CYRIX_PCI_MASTER:
+                                master_0 = pci_dev_get(dev);
+                                break;
+                        case PCI_DEVICE_ID_CYRIX_5530_LEGACY:
+                                cs5530_0 = pci_dev_get(dev);
+                                break;
+                }
+        }
+        if (!master_0) {
+                printk(KERN_ERR DRV_NAME ": unable to locate PCI MASTER function\n");
+                goto fail_put;
+        }
+        if (!cs5530_0) {
+                printk(KERN_ERR DRV_NAME ": unable to locate CS5530 LEGACY function\n");
+                goto fail_put;
+        }
+
+        pci_set_master(cs5530_0);
+        compiler_warning_pointless_fix = pci_set_mwi(cs5530_0);
+
+        /*
+         * Set PCI CacheLineSize to 16-bytes:
+         * --> Write 0x04 into 8-bit PCI CACHELINESIZE reg of function 0 of the cs5530
+         *
+         * Note: This value is constant because the 5530 is only a Geode companion
+         */
+
+        pci_write_config_byte(cs5530_0, PCI_CACHE_LINE_SIZE, 0x04);
+
+        /*
+         * Disable trapping of UDMA register accesses (Win98 hack):
+         * --> Write 0x5006 into 16-bit reg at offset 0xd0 of function 0 of the cs5530
+         */
+
+        pci_write_config_word(cs5530_0, 0xd0, 0x5006);
+
+        /*
+         * Bit-1 at 0x40 enables MemoryWriteAndInvalidate on internal X-bus:
+         * The other settings are what is necessary to get the register
+         * into a sane state for IDE DMA operation.
+         */
+
+        pci_write_config_byte(master_0, 0x40, 0x1e);
+
+        /*
+         * Set max PCI burst size (16-bytes seems to work best):
+         *         16bytes: set bit-1 at 0x41 (reg value of 0x16)
+         *      all others: clear bit-1 at 0x41, and do:
+         *        128bytes: OR 0x00 at 0x41
+         *        256bytes: OR 0x04 at 0x41
+         *        512bytes: OR 0x08 at 0x41
+         *       1024bytes: OR 0x0c at 0x41
+         */
+
+        pci_write_config_byte(master_0, 0x41, 0x14);
+
+        /*
+         * These settings are necessary to get the chip
+         * into a sane state for IDE DMA operation.
+         */
+
+        pci_write_config_byte(master_0, 0x42, 0x00);
+        pci_write_config_byte(master_0, 0x43, 0xc1);
+
+        pci_dev_put(master_0);
+        pci_dev_put(cs5530_0);
+
+        if (cs5530_is_palmax())
+                port_info[1] = &info_palmax_secondary;
+
+        /* Now kick off ATA set up */
+        return ata_pci_init_one(dev, port_info, 2);
+
+fail_put:
+        if (master_0)
+                pci_dev_put(master_0);
+        if (cs5530_0)
+                pci_dev_put(cs5530_0);
+        return -ENODEV;
+}
+
+static struct pci_device_id cs5530[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5530_IDE), },
+        { 0, },
+};
+
+static struct pci_driver cs5530_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = cs5530,
+        .probe          = cs5530_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init cs5530_init(void)
+{
+        return pci_register_driver(&cs5530_pci_driver);
+}
+
+
+static void __exit cs5530_exit(void)
+{
+        pci_unregister_driver(&cs5530_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for the Cyrix/NS/AMD 5530");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, cs5530);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(cs5530_init);
+module_exit(cs5530_exit);
diff --git a/drivers/ata/pata_cs5535.c b/drivers/ata/pata_cs5535.c
new file mode 100644
index 000000000000..69d6b4258724
--- /dev/null
+++ b/drivers/ata/pata_cs5535.c
@@ -0,0 +1,291 @@
+/*
+ * pata-cs5535.c        - CS5535 PATA for new ATA layer
+ *                        (C) 2005-2006 Red Hat Inc
+ *                        Alan Cox <alan@redhat.com>
+ *
+ * based upon cs5535.c from AMD <Jens.Altmann@amd.com> as cleaned up and
+ * made readable and Linux style by Wolfgang Zuleger <wolfgang.zuleger@gmx.de
+ * and Alexander Kiausch <alex.kiausch@t-online.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ * Loosely based on the piix & svwks drivers.
+ *
+ * Documentation:
+ *      Available from AMD web site.
+ * TODO
+ *      Review errata to see if serializing is neccessary
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <asm/msr.h>
+
+#define DRV_NAME        "cs5535"
+#define DRV_VERSION     "0.2.10"
+
+/*
+ *      The Geode (Aka Athlon GX now) uses an internal MSR based
+ *      bus system for control. Demented but there you go.
+ */
+
+#define MSR_ATAC_BASE           0x51300000
+#define ATAC_GLD_MSR_CAP        (MSR_ATAC_BASE+0)
+#define ATAC_GLD_MSR_CONFIG    (MSR_ATAC_BASE+0x01)
+#define ATAC_GLD_MSR_SMI       (MSR_ATAC_BASE+0x02)
+#define ATAC_GLD_MSR_ERROR     (MSR_ATAC_BASE+0x03)
+#define ATAC_GLD_MSR_PM        (MSR_ATAC_BASE+0x04)
+#define ATAC_GLD_MSR_DIAG      (MSR_ATAC_BASE+0x05)
+#define ATAC_IO_BAR            (MSR_ATAC_BASE+0x08)
+#define ATAC_RESET             (MSR_ATAC_BASE+0x10)
+#define ATAC_CH0D0_PIO         (MSR_ATAC_BASE+0x20)
+#define ATAC_CH0D0_DMA         (MSR_ATAC_BASE+0x21)
+#define ATAC_CH0D1_PIO         (MSR_ATAC_BASE+0x22)
+#define ATAC_CH0D1_DMA         (MSR_ATAC_BASE+0x23)
+#define ATAC_PCI_ABRTERR       (MSR_ATAC_BASE+0x24)
+
+#define ATAC_BM0_CMD_PRIM      0x00
+#define ATAC_BM0_STS_PRIM      0x02
+#define ATAC_BM0_PRD           0x04
+
+#define CS5535_CABLE_DETECT    0x48
+
+#define CS5535_BAD_PIO(timings) ( (timings&~0x80000000UL)==0x00009172 )
+
+/**
+ *      cs5535_pre_reset        -       detect cable type
+ *      @ap: Port to detect on
+ *
+ *      Perform cable detection for ATA66 capable cable. Return a libata
+ *      cable type.
+ */
+
+static int cs5535_pre_reset(struct ata_port *ap)
+{
+        u8 cable;
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+        pci_read_config_byte(pdev, CS5535_CABLE_DETECT, &cable);
+        if (cable & 1)
+                ap->cbl = ATA_CBL_PATA80;
+        else
+                ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      cs5535_error_handler            -       reset/probe
+ *      @ap: Port to reset
+ *
+ *      Reset and configure a port
+ */
+
+static void cs5535_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, cs5535_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      cs5535_set_piomode              -       PIO setup
+ *      @ap: ATA interface
+ *      @adev: device on the interface
+ *
+ *      Set our PIO requirements. The CS5535 is pretty clean about all this
+ */
+
+static void cs5535_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        static const u16 pio_timings[5] = {
+                0xF7F4, 0x53F3, 0x13F1, 0x5131, 0x1131
+        };
+        static const u16 pio_cmd_timings[5] = {
+                0xF7F4, 0x53F3, 0x13F1, 0x5131, 0x1131
+        };
+        u32 reg, dummy;
+        struct ata_device *pair = ata_dev_pair(adev);
+
+        int mode = adev->pio_mode - XFER_PIO_0;
+        int cmdmode = mode;
+
+        /* Command timing has to be for the lowest of the pair of devices */
+        if (pair) {
+                int pairmode = pair->pio_mode - XFER_PIO_0;
+                cmdmode = min(mode, pairmode);
+                /* Write the other drive timing register if it changed */
+                if (cmdmode < pairmode)
+                        wrmsr(ATAC_CH0D0_PIO + 2 * pair->devno,
+                                pio_cmd_timings[cmdmode] << 16 | pio_timings[pairmode], 0);
+        }
+        /* Write the drive timing register */
+        wrmsr(ATAC_CH0D0_PIO + 2 * adev->devno,
+                pio_cmd_timings[cmdmode] << 16 | pio_timings[mode], 0);
+
+        /* Set the PIO "format 1" bit in the DMA timing register */
+        rdmsr(ATAC_CH0D0_DMA + 2 * adev->devno, reg, dummy);
+        wrmsr(ATAC_CH0D0_DMA + 2 * adev->devno, reg | 0x80000000UL, 0);
+}
+
+/**
+ *      cs5535_set_dmamode              -       DMA timing setup
+ *      @ap: ATA interface
+ *      @adev: Device being configured
+ *
+ */
+
+static void cs5535_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        static const u32 udma_timings[5] = {
+                0x7F7436A1, 0x7F733481, 0x7F723261, 0x7F713161, 0x7F703061
+        };
+        static const u32 mwdma_timings[3] = {
+                0x7F0FFFF3, 0x7F035352, 0x7F024241
+        };
+        u32 reg, dummy;
+        int mode = adev->dma_mode;
+
+        rdmsr(ATAC_CH0D0_DMA + 2 * adev->devno, reg, dummy);
+        reg &= 0x80000000UL;
+        if (mode >= XFER_UDMA_0)
+                reg |= udma_timings[mode - XFER_UDMA_0];
+        else
+                reg |= mwdma_timings[mode - XFER_MW_DMA_0];
+        wrmsr(ATAC_CH0D0_DMA + 2 * adev->devno, reg, 0);
+}
+
+static struct scsi_host_template cs5535_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations cs5535_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = cs5535_set_piomode,
+        .set_dmamode    = cs5535_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = cs5535_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/**
+ *      cs5535_init_one         -       Initialise a CS5530
+ *      @dev: PCI device
+ *      @id: Entry in match table
+ *
+ *      Install a driver for the newly found CS5530 companion chip. Most of
+ *      this is just housekeeping. We have to set the chip up correctly and
+ *      turn off various bits of emulation magic.
+ */
+
+static int cs5535_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+        static struct ata_port_info info = {
+                .sht = &cs5535_sht,
+                .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x1f,
+                .port_ops = &cs5535_port_ops
+        };
+        struct ata_port_info *ports[1] = { &info };
+
+        u32 timings, dummy;
+
+        /* Check the BIOS set the initial timing clock. If not set the
+           timings for PIO0 */
+        rdmsr(ATAC_CH0D0_PIO, timings, dummy);
+        if (CS5535_BAD_PIO(timings))
+                wrmsr(ATAC_CH0D0_PIO, 0xF7F4F7F4UL, 0);
+        rdmsr(ATAC_CH0D1_PIO, timings, dummy);
+        if (CS5535_BAD_PIO(timings))
+                wrmsr(ATAC_CH0D1_PIO, 0xF7F4F7F4UL, 0);
+        return ata_pci_init_one(dev, ports, 1);
+}
+
+static struct pci_device_id cs5535[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_NS, 0x002D), },
+        { 0, },
+};
+
+static struct pci_driver cs5535_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = cs5535,
+        .probe          = cs5535_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init cs5535_init(void)
+{
+        return pci_register_driver(&cs5535_pci_driver);
+}
+
+
+static void __exit cs5535_exit(void)
+{
+        pci_unregister_driver(&cs5535_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox, Jens Altmann, Wolfgan Zuleger, Alexander Kiausch");
+MODULE_DESCRIPTION("low-level driver for the NS/AMD 5530");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, cs5535);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(cs5535_init);
+module_exit(cs5535_exit);
diff --git a/drivers/ata/pata_cypress.c b/drivers/ata/pata_cypress.c
new file mode 100644
index 000000000000..fd55474e0d15
--- /dev/null
+++ b/drivers/ata/pata_cypress.c
@@ -0,0 +1,227 @@
+/*
+ * pata_cypress.c       - Cypress PATA for new ATA layer
+ *                        (C) 2006 Red Hat Inc
+ *                        Alan Cox <alan@redhat.com>
+ *
+ * Based heavily on
+ * linux/drivers/ide/pci/cy82c693.c             Version 0.40    Sep. 10, 2002
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_cypress"
+#define DRV_VERSION "0.1.2"
+
+/* here are the offset definitions for the registers */
+
+enum {
+        CY82_IDE_CMDREG         = 0x04,
+        CY82_IDE_ADDRSETUP      = 0x48,
+        CY82_IDE_MASTER_IOR     = 0x4C,
+        CY82_IDE_MASTER_IOW     = 0x4D,
+        CY82_IDE_SLAVE_IOR      = 0x4E,
+        CY82_IDE_SLAVE_IOW      = 0x4F,
+        CY82_IDE_MASTER_8BIT    = 0x50,
+        CY82_IDE_SLAVE_8BIT     = 0x51,
+
+        CY82_INDEX_PORT         = 0x22,
+        CY82_DATA_PORT          = 0x23,
+
+        CY82_INDEX_CTRLREG1     = 0x01,
+        CY82_INDEX_CHANNEL0     = 0x30,
+        CY82_INDEX_CHANNEL1     = 0x31,
+        CY82_INDEX_TIMEOUT      = 0x32
+};
+
+static int cy82c693_pre_reset(struct ata_port *ap)
+{
+        ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+}
+
+static void cy82c693_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, cy82c693_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      cy82c693_set_piomode    -       set initial PIO mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Called to do the PIO mode setup.
+ */
+
+static void cy82c693_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        struct ata_timing t;
+        const unsigned long T = 1000000 / 33;
+        short time_16, time_8;
+        u32 addr;
+
+        if (ata_timing_compute(adev, adev->pio_mode, &t, T, 1) < 0) {
+                printk(KERN_ERR DRV_NAME ": mome computation failed.\n");
+                return;
+        }
+
+        time_16 = FIT(t.recover, 0, 15) | (FIT(t.active, 0, 15) << 4);
+        time_8 = FIT(t.act8b, 0, 15) | (FIT(t.rec8b, 0, 15) << 4);
+
+        if (adev->devno == 0) {
+                pci_read_config_dword(pdev, CY82_IDE_ADDRSETUP, &addr);
+
+                addr &= ~0x0F;  /* Mask bits */
+                addr |= FIT(t.setup, 0, 15);
+
+                pci_write_config_dword(pdev, CY82_IDE_ADDRSETUP, addr);
+                pci_write_config_byte(pdev, CY82_IDE_MASTER_IOR, time_16);
+                pci_write_config_byte(pdev, CY82_IDE_MASTER_IOW, time_16);
+                pci_write_config_byte(pdev, CY82_IDE_MASTER_8BIT, time_8);
+        } else {
+                pci_read_config_dword(pdev, CY82_IDE_ADDRSETUP, &addr);
+
+                addr &= ~0xF0;  /* Mask bits */
+                addr |= (FIT(t.setup, 0, 15) << 4);
+
+                pci_write_config_dword(pdev, CY82_IDE_ADDRSETUP, addr);
+                pci_write_config_byte(pdev, CY82_IDE_SLAVE_IOR, time_16);
+                pci_write_config_byte(pdev, CY82_IDE_SLAVE_IOW, time_16);
+                pci_write_config_byte(pdev, CY82_IDE_SLAVE_8BIT, time_8);
+        }
+}
+
+/**
+ *      cy82c693_set_dmamode    -       set initial DMA mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Called to do the DMA mode setup.
+ */
+
+static void cy82c693_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        int reg = CY82_INDEX_CHANNEL0 + ap->port_no;
+
+        /* Be afraid, be very afraid. Magic registers  in low I/O space */
+        outb(reg, 0x22);
+        outb(adev->dma_mode - XFER_MW_DMA_0, 0x23);
+
+        /* 0x50 gives the best behaviour on the Alpha's using this chip */
+        outb(CY82_INDEX_TIMEOUT, 0x22);
+        outb(0x50, 0x23);
+}
+
+static struct scsi_host_template cy82c693_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations cy82c693_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = cy82c693_set_piomode,
+        .set_dmamode    = cy82c693_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = cy82c693_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static int cy82c693_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+        static struct ata_port_info info = {
+                .sht = &cy82c693_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .port_ops = &cy82c693_port_ops
+        };
+        static struct ata_port_info *port_info[1] = { &info };
+
+        /* Devfn 1 is the ATA primary. The secondary is magic and on devfn2. For the
+           moment we don't handle the secondary. FIXME */
+
+        if (PCI_FUNC(pdev->devfn) != 1)
+                return -ENODEV;
+
+        return ata_pci_init_one(pdev, port_info, 1);
+}
+
+static struct pci_device_id cy82c693[] = {
+        { PCI_VENDOR_ID_CONTAQ, PCI_DEVICE_ID_CONTAQ_82C693, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+        { 0, },
+};
+
+static struct pci_driver cy82c693_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = cy82c693,
+        .probe          = cy82c693_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init cy82c693_init(void)
+{
+        return pci_register_driver(&cy82c693_pci_driver);
+}
+
+
+static void __exit cy82c693_exit(void)
+{
+        pci_unregister_driver(&cy82c693_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for the CY82C693 PATA controller");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, cy82c693);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(cy82c693_init);
+module_exit(cy82c693_exit);
diff --git a/drivers/ata/pata_efar.c b/drivers/ata/pata_efar.c
new file mode 100644
index 000000000000..c30bc181304f
--- /dev/null
+++ b/drivers/ata/pata_efar.c
@@ -0,0 +1,342 @@
+/*
+ *    pata_efar.c - EFAR PIIX clone controller driver
+ *
+ *      (C) 2005 Red Hat <alan@redhat.com>
+ *
+ *    Some parts based on ata_piix.c by Jeff Garzik and others.
+ *
+ *    The EFAR is a PIIX4 clone with UDMA66 support. Unlike the later
+ *    Intel ICH controllers the EFAR widened the UDMA mode register bits
+ *    and doesn't require the funky clock selection.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/ata.h>
+
+#define DRV_NAME        "pata_efar"
+#define DRV_VERSION     "0.4.1"
+
+/**
+ *      efar_pre_reset  -       check for 40/80 pin
+ *      @ap: Port
+ *
+ *      Perform cable detection for the EFAR ATA interface. This is
+ *      different to the PIIX arrangement
+ */
+
+static int efar_pre_reset(struct ata_port *ap)
+{
+        static const struct pci_bits efar_enable_bits[] = {
+                { 0x41U, 1U, 0x80UL, 0x80UL },  /* port 0 */
+                { 0x43U, 1U, 0x80UL, 0x80UL },  /* port 1 */
+        };
+
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u8 tmp;
+
+        if (!pci_test_config_bits(pdev, &efar_enable_bits[ap->port_no])) {
+                ata_port_disable(ap);
+                printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+                return 0;
+        }
+        pci_read_config_byte(pdev, 0x47, &tmp);
+        if (tmp & (2 >> ap->port_no))
+                ap->cbl = ATA_CBL_PATA40;
+        else
+                ap->cbl = ATA_CBL_PATA80;
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      efar_probe_reset - Probe specified port on PATA host controller
+ *      @ap: Port to probe
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void efar_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, efar_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      efar_set_piomode - Initialize host controller PATA PIO timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: um
+ *
+ *      Set PIO mode for device, in host controller PCI config space.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void efar_set_piomode (struct ata_port *ap, struct ata_device *adev)
+{
+        unsigned int pio        = adev->pio_mode - XFER_PIO_0;
+        struct pci_dev *dev     = to_pci_dev(ap->host->dev);
+        unsigned int idetm_port= ap->port_no ? 0x42 : 0x40;
+        u16 idetm_data;
+        int control = 0;
+
+        /*
+         *      See Intel Document 298600-004 for the timing programing rules
+         *      for PIIX/ICH. The EFAR is a clone so very similar
+         */
+
+        static const     /* ISP  RTC */
+        u8 timings[][2] = { { 0, 0 },
+                            { 0, 0 },
+                            { 1, 0 },
+                            { 2, 1 },
+                            { 2, 3 }, };
+
+        if (pio > 2)
+                control |= 1;   /* TIME1 enable */
+        if (ata_pio_need_iordy(adev))   /* PIO 3/4 require IORDY */
+                control |= 2;   /* IE enable */
+        /* Intel specifies that the PPE functionality is for disk only */
+        if (adev->class == ATA_DEV_ATA)
+                control |= 4;   /* PPE enable */
+
+        pci_read_config_word(dev, idetm_port, &idetm_data);
+
+        /* Enable PPE, IE and TIME as appropriate */
+
+        if (adev->devno == 0) {
+                idetm_data &= 0xCCF0;
+                idetm_data |= control;
+                idetm_data |= (timings[pio][0] << 12) |
+                        (timings[pio][1] << 8);
+        } else {
+                int shift = 4 * ap->port_no;
+                u8 slave_data;
+
+                idetm_data &= 0xCC0F;
+                idetm_data |= (control << 4);
+
+                /* Slave timing in seperate register */
+                pci_read_config_byte(dev, 0x44, &slave_data);
+                slave_data &= 0x0F << shift;
+                slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << shift;
+                pci_write_config_byte(dev, 0x44, slave_data);
+        }
+
+        idetm_data |= 0x4000;   /* Ensure SITRE is enabled */
+        pci_write_config_word(dev, idetm_port, idetm_data);
+}
+
+/**
+ *      efar_set_dmamode - Initialize host controller PATA DMA timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device to program
+ *
+ *      Set UDMA/MWDMA mode for device, in host controller PCI config space.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void efar_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *dev     = to_pci_dev(ap->host->dev);
+        u8 master_port          = ap->port_no ? 0x42 : 0x40;
+        u16 master_data;
+        u8 speed                = adev->dma_mode;
+        int devid               = adev->devno + 2 * ap->port_no;
+        u8 udma_enable;
+
+        static const     /* ISP  RTC */
+        u8 timings[][2] = { { 0, 0 },
+                            { 0, 0 },
+                            { 1, 0 },
+                            { 2, 1 },
+                            { 2, 3 }, };
+
+        pci_read_config_word(dev, master_port, &master_data);
+        pci_read_config_byte(dev, 0x48, &udma_enable);
+
+        if (speed >= XFER_UDMA_0) {
+                unsigned int udma       = adev->dma_mode - XFER_UDMA_0;
+                u16 udma_timing;
+
+                udma_enable |= (1 << devid);
+
+                /* Load the UDMA mode number */
+                pci_read_config_word(dev, 0x4A, &udma_timing);
+                udma_timing &= ~(7 << (4 * devid));
+                udma_timing |= udma << (4 * devid);
+                pci_write_config_word(dev, 0x4A, udma_timing);
+        } else {
+                /*
+                 * MWDMA is driven by the PIO timings. We must also enable
+                 * IORDY unconditionally along with TIME1. PPE has already
+                 * been set when the PIO timing was set.
+                 */
+                unsigned int mwdma      = adev->dma_mode - XFER_MW_DMA_0;
+                unsigned int control;
+                u8 slave_data;
+                const unsigned int needed_pio[3] = {
+                        XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
+                };
+                int pio = needed_pio[mwdma] - XFER_PIO_0;
+
+                control = 3;    /* IORDY|TIME1 */
+
+                /* If the drive MWDMA is faster than it can do PIO then
+                   we must force PIO into PIO0 */
+
+                if (adev->pio_mode < needed_pio[mwdma])
+                        /* Enable DMA timing only */
+                        control |= 8;   /* PIO cycles in PIO0 */
+
+                if (adev->devno) {      /* Slave */
+                        master_data &= 0xFF4F;  /* Mask out IORDY|TIME1|DMAONLY */
+                        master_data |= control << 4;
+                        pci_read_config_byte(dev, 0x44, &slave_data);
+                        slave_data &= (0x0F + 0xE1 * ap->port_no);
+                        /* Load the matching timing */
+                        slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
+                        pci_write_config_byte(dev, 0x44, slave_data);
+                } else {        /* Master */
+                        master_data &= 0xCCF4;  /* Mask out IORDY|TIME1|DMAONLY
+                                                   and master timing bits */
+                        master_data |= control;
+                        master_data |=
+                                (timings[pio][0] << 12) |
+                                (timings[pio][1] << 8);
+                }
+                udma_enable &= ~(1 << devid);
+                pci_write_config_word(dev, master_port, master_data);
+        }
+        pci_write_config_byte(dev, 0x48, udma_enable);
+}
+
+static struct scsi_host_template efar_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static const struct ata_port_operations efar_ops = {
+        .port_disable           = ata_port_disable,
+        .set_piomode            = efar_set_piomode,
+        .set_dmamode            = efar_set_dmamode,
+        .mode_filter            = ata_pci_default_filter,
+
+        .tf_load                = ata_tf_load,
+        .tf_read                = ata_tf_read,
+        .check_status           = ata_check_status,
+        .exec_command           = ata_exec_command,
+        .dev_select             = ata_std_dev_select,
+
+        .freeze                 = ata_bmdma_freeze,
+        .thaw                   = ata_bmdma_thaw,
+        .error_handler          = efar_error_handler,
+        .post_internal_cmd      = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup            = ata_bmdma_setup,
+        .bmdma_start            = ata_bmdma_start,
+        .bmdma_stop             = ata_bmdma_stop,
+        .bmdma_status           = ata_bmdma_status,
+        .qc_prep                = ata_qc_prep,
+        .qc_issue               = ata_qc_issue_prot,
+        .data_xfer              = ata_pio_data_xfer,
+
+        .eng_timeout            = ata_eng_timeout,
+
+        .irq_handler            = ata_interrupt,
+        .irq_clear              = ata_bmdma_irq_clear,
+
+        .port_start             = ata_port_start,
+        .port_stop              = ata_port_stop,
+        .host_stop              = ata_host_stop,
+};
+
+
+/**
+ *      efar_init_one - Register EFAR ATA PCI device with kernel services
+ *      @pdev: PCI device to register
+ *      @ent: Entry in efar_pci_tbl matching with @pdev
+ *
+ *      Called from kernel PCI layer.
+ *
+ *      LOCKING:
+ *      Inherited from PCI layer (may sleep).
+ *
+ *      RETURNS:
+ *      Zero on success, or -ERRNO value.
+ */
+
+static int efar_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+        static int printed_version;
+        static struct ata_port_info info = {
+                .sht            = &efar_sht,
+                .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask       = 0x1f, /* pio0-4 */
+                .mwdma_mask     = 0x07, /* mwdma1-2 */
+                .udma_mask      = 0x0f, /* UDMA 66 */
+                .port_ops       = &efar_ops,
+        };
+        static struct ata_port_info *port_info[2] = { &info, &info };
+
+        if (!printed_version++)
+                dev_printk(KERN_DEBUG, &pdev->dev,
+                           "version " DRV_VERSION "\n");
+
+        return ata_pci_init_one(pdev, port_info, 2);
+}
+
+static const struct pci_device_id efar_pci_tbl[] = {
+        { 0x1055, 0x9130, PCI_ANY_ID, PCI_ANY_ID, },
+        { }     /* terminate list */
+};
+
+static struct pci_driver efar_pci_driver = {
+        .name                   = DRV_NAME,
+        .id_table               = efar_pci_tbl,
+        .probe                  = efar_init_one,
+        .remove                 = ata_pci_remove_one,
+};
+
+static int __init efar_init(void)
+{
+        return pci_register_driver(&efar_pci_driver);
+}
+
+static void __exit efar_exit(void)
+{
+        pci_unregister_driver(&efar_pci_driver);
+}
+
+
+module_init(efar_init);
+module_exit(efar_exit);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("SCSI low-level driver for EFAR PIIX clones");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, efar_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+
diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c
new file mode 100644
index 000000000000..94bb1dfc3f19
--- /dev/null
+++ b/drivers/ata/pata_hpt366.c
@@ -0,0 +1,478 @@
+/*
+ * Libata driver for the highpoint 366 and 368 UDMA66 ATA controllers.
+ *
+ * This driver is heavily based upon:
+ *
+ * linux/drivers/ide/pci/hpt366.c               Version 0.36    April 25, 2003
+ *
+ * Copyright (C) 1999-2003              Andre Hedrick <andre@linux-ide.org>
+ * Portions Copyright (C) 2001          Sun Microsystems, Inc.
+ * Portions Copyright (C) 2003          Red Hat Inc
+ *
+ *
+ * TODO
+ *      Maybe PLL mode
+ *      Look into engine reset on timeout errors. Should not be
+ *              required.
+ */
+
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME        "pata_hpt366"
+#define DRV_VERSION     "0.5"
+
+struct hpt_clock {
+        u8      xfer_speed;
+        u32     timing;
+};
+
+/* key for bus clock timings
+ * bit
+ * 0:3    data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
+ *        DMA. cycles = value + 1
+ * 4:8    data_low_time. active time of DIOW_/DIOR_ for PIO and MW
+ *        DMA. cycles = value + 1
+ * 9:12   cmd_high_time. inactive time of DIOW_/DIOR_ during task file
+ *        register access.
+ * 13:17  cmd_low_time. active time of DIOW_/DIOR_ during task file
+ *        register access.
+ * 18:21  udma_cycle_time. clock freq and clock cycles for UDMA xfer.
+ *        during task file register access.
+ * 22:24  pre_high_time. time to initialize 1st cycle for PIO and MW DMA
+ *        xfer.
+ * 25:27  cmd_pre_high_time. time to initialize 1st PIO cycle for task
+ *        register access.
+ * 28     UDMA enable
+ * 29     DMA enable
+ * 30     PIO_MST enable. if set, the chip is in bus master mode during
+ *        PIO.
+ * 31     FIFO enable.
+ */
+
+static const struct hpt_clock hpt366_40[] = {
+        {       XFER_UDMA_4,    0x900fd943      },
+        {       XFER_UDMA_3,    0x900ad943      },
+        {       XFER_UDMA_2,    0x900bd943      },
+        {       XFER_UDMA_1,    0x9008d943      },
+        {       XFER_UDMA_0,    0x9008d943      },
+
+        {       XFER_MW_DMA_2,  0xa008d943      },
+        {       XFER_MW_DMA_1,  0xa010d955      },
+        {       XFER_MW_DMA_0,  0xa010d9fc      },
+
+        {       XFER_PIO_4,     0xc008d963      },
+        {       XFER_PIO_3,     0xc010d974      },
+        {       XFER_PIO_2,     0xc010d997      },
+        {       XFER_PIO_1,     0xc010d9c7      },
+        {       XFER_PIO_0,     0xc018d9d9      },
+        {       0,              0x0120d9d9      }
+};
+
+static const struct hpt_clock hpt366_33[] = {
+        {       XFER_UDMA_4,    0x90c9a731      },
+        {       XFER_UDMA_3,    0x90cfa731      },
+        {       XFER_UDMA_2,    0x90caa731      },
+        {       XFER_UDMA_1,    0x90cba731      },
+        {       XFER_UDMA_0,    0x90c8a731      },
+
+        {       XFER_MW_DMA_2,  0xa0c8a731      },
+        {       XFER_MW_DMA_1,  0xa0c8a732      },      /* 0xa0c8a733 */
+        {       XFER_MW_DMA_0,  0xa0c8a797      },
+
+        {       XFER_PIO_4,     0xc0c8a731      },
+        {       XFER_PIO_3,     0xc0c8a742      },
+        {       XFER_PIO_2,     0xc0d0a753      },
+        {       XFER_PIO_1,     0xc0d0a7a3      },      /* 0xc0d0a793 */
+        {       XFER_PIO_0,     0xc0d0a7aa      },      /* 0xc0d0a7a7 */
+        {       0,              0x0120a7a7      }
+};
+
+static const struct hpt_clock hpt366_25[] = {
+        {       XFER_UDMA_4,    0x90c98521      },
+        {       XFER_UDMA_3,    0x90cf8521      },
+        {       XFER_UDMA_2,    0x90cf8521      },
+        {       XFER_UDMA_1,    0x90cb8521      },
+        {       XFER_UDMA_0,    0x90cb8521      },
+
+        {       XFER_MW_DMA_2,  0xa0ca8521      },
+        {       XFER_MW_DMA_1,  0xa0ca8532      },
+        {       XFER_MW_DMA_0,  0xa0ca8575      },
+
+        {       XFER_PIO_4,     0xc0ca8521      },
+        {       XFER_PIO_3,     0xc0ca8532      },
+        {       XFER_PIO_2,     0xc0ca8542      },
+        {       XFER_PIO_1,     0xc0d08572      },
+        {       XFER_PIO_0,     0xc0d08585      },
+        {       0,              0x01208585      }
+};
+
+static const char *bad_ata33[] = {
+        "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", "Maxtor 90845U3", "Maxtor 90650U2",
+        "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2",
+        "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4",
+        "Maxtor 90510D4",
+        "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2",
+        "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4",
+        "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2",
+        NULL
+};
+
+static const char *bad_ata66_4[] = {
+        "IBM-DTLA-307075",
+        "IBM-DTLA-307060",
+        "IBM-DTLA-307045",
+        "IBM-DTLA-307030",
+        "IBM-DTLA-307020",
+        "IBM-DTLA-307015",
+        "IBM-DTLA-305040",
+        "IBM-DTLA-305030",
+        "IBM-DTLA-305020",
+        "IC35L010AVER07-0",
+        "IC35L020AVER07-0",
+        "IC35L030AVER07-0",
+        "IC35L040AVER07-0",
+        "IC35L060AVER07-0",
+        "WDC AC310200R",
+        NULL
+};
+
+static const char *bad_ata66_3[] = {
+        "WDC AC310200R",
+        NULL
+};
+
+static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr, const char *list[])
+{
+        unsigned char model_num[40];
+        char *s;
+        unsigned int len;
+        int i = 0;
+
+        ata_id_string(dev->id, model_num, ATA_ID_PROD_OFS, sizeof(model_num));
+        s = &model_num[0];
+        len = strnlen(s, sizeof(model_num));
+
+        /* ATAPI specifies that empty space is blank-filled; remove blanks */
+        while ((len > 0) && (s[len - 1] == ' ')) {
+                len--;
+                s[len] = 0;
+        }
+
+        while(list[i] != NULL) {
+                if (!strncmp(list[i], s, len)) {
+                        printk(KERN_WARNING DRV_NAME ": %s is not supported for %s.\n",
+                                modestr, list[i]);
+                        return 1;
+                }
+                i++;
+        }
+        return 0;
+}
+
+/**
+ *      hpt366_filter   -       mode selection filter
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Block UDMA on devices that cause trouble with this controller.
+ */
+
+static unsigned long hpt366_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask)
+{
+        if (adev->class == ATA_DEV_ATA) {
+                if (hpt_dma_blacklisted(adev, "UDMA",  bad_ata33))
+                        mask &= ~ATA_MASK_UDMA;
+                if (hpt_dma_blacklisted(adev, "UDMA3", bad_ata66_3))
+                        mask &= ~(0x07 << ATA_SHIFT_UDMA);
+                if (hpt_dma_blacklisted(adev, "UDMA4", bad_ata66_4))
+                        mask &= ~(0x0F << ATA_SHIFT_UDMA);
+        }
+        return ata_pci_default_filter(ap, adev, mask);
+}
+
+/**
+ *      hpt36x_find_mode        -       reset the hpt36x bus
+ *      @ap: ATA port
+ *      @speed: transfer mode
+ *
+ *      Return the 32bit register programming information for this channel
+ *      that matches the speed provided.
+ */
+
+static u32 hpt36x_find_mode(struct ata_port *ap, int speed)
+{
+        struct hpt_clock *clocks = ap->host->private_data;
+
+        while(clocks->xfer_speed) {
+                if (clocks->xfer_speed == speed)
+                        return clocks->timing;
+                clocks++;
+        }
+        BUG();
+        return 0xffffffffU;     /* silence compiler warning */
+}
+
+static int hpt36x_pre_reset(struct ata_port *ap)
+{
+        u8 ata66;
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+        pci_read_config_byte(pdev, 0x5A, &ata66);
+        if (ata66 & (1 << ap->port_no))
+                ap->cbl = ATA_CBL_PATA40;
+        else
+                ap->cbl = ATA_CBL_PATA80;
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      hpt36x_error_handler    -       reset the hpt36x bus
+ *      @ap: ATA port to reset
+ *
+ *      Perform the reset handling for the 366/368
+ */
+
+static void hpt36x_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, hpt36x_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      hpt366_set_piomode              -       PIO setup
+ *      @ap: ATA interface
+ *      @adev: device on the interface
+ *
+ *      Perform PIO mode setup.
+ */
+
+static void hpt366_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u32 addr1, addr2;
+        u32 reg;
+        u32 mode;
+        u8 fast;
+
+        addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+        addr2 = 0x51 + 4 * ap->port_no;
+
+        /* Fast interrupt prediction disable, hold off interrupt disable */
+        pci_read_config_byte(pdev, addr2, &fast);
+        if (fast & 0x80) {
+                fast &= ~0x80;
+                pci_write_config_byte(pdev, addr2, fast);
+        }
+
+        pci_read_config_dword(pdev, addr1, &reg);
+        mode = hpt36x_find_mode(ap, adev->pio_mode);
+        mode &= ~0x8000000;     /* No FIFO in PIO */
+        mode &= ~0x30070000;    /* Leave config bits alone */
+        reg &= 0x30070000;      /* Strip timing bits */
+        pci_write_config_dword(pdev, addr1, reg | mode);
+}
+
+/**
+ *      hpt366_set_dmamode              -       DMA timing setup
+ *      @ap: ATA interface
+ *      @adev: Device being configured
+ *
+ *      Set up the channel for MWDMA or UDMA modes. Much the same as with
+ *      PIO, load the mode number and then set MWDMA or UDMA flag.
+ */
+
+static void hpt366_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u32 addr1, addr2;
+        u32 reg;
+        u32 mode;
+        u8 fast;
+
+        addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+        addr2 = 0x51 + 4 * ap->port_no;
+
+        /* Fast interrupt prediction disable, hold off interrupt disable */
+        pci_read_config_byte(pdev, addr2, &fast);
+        if (fast & 0x80) {
+                fast &= ~0x80;
+                pci_write_config_byte(pdev, addr2, fast);
+        }
+
+        pci_read_config_dword(pdev, addr1, &reg);
+        mode = hpt36x_find_mode(ap, adev->dma_mode);
+        mode |= 0x8000000;      /* FIFO in MWDMA or UDMA */
+        mode &= ~0xC0000000;    /* Leave config bits alone */
+        reg &= 0xC0000000;      /* Strip timing bits */
+        pci_write_config_dword(pdev, addr1, reg | mode);
+}
+
+static struct scsi_host_template hpt36x_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+/*
+ *      Configuration for HPT366/68
+ */
+
+static struct ata_port_operations hpt366_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = hpt366_set_piomode,
+        .set_dmamode    = hpt366_set_dmamode,
+        .mode_filter    = hpt366_filter,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = hpt36x_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/**
+ *      hpt36x_init_one         -       Initialise an HPT366/368
+ *      @dev: PCI device
+ *      @id: Entry in match table
+ *
+ *      Initialise an HPT36x device. There are some interesting complications
+ *      here. Firstly the chip may report 366 and be one of several variants.
+ *      Secondly all the timings depend on the clock for the chip which we must
+ *      detect and look up
+ *
+ *      This is the known chip mappings. It may be missing a couple of later
+ *      releases.
+ *
+ *      Chip version            PCI             Rev     Notes
+ *      HPT366                  4 (HPT366)      0       UDMA66
+ *      HPT366                  4 (HPT366)      1       UDMA66
+ *      HPT368                  4 (HPT366)      2       UDMA66
+ *      HPT37x/30x              4 (HPT366)      3+      Other driver
+ *
+ */
+
+static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+        static struct ata_port_info info_hpt366 = {
+                .sht = &hpt36x_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x1f,
+                .port_ops = &hpt366_port_ops
+        };
+        struct ata_port_info *port_info[2] = {&info_hpt366, &info_hpt366};
+
+        u32 class_rev;
+        u32 reg1;
+        u8 drive_fast;
+
+        pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
+        class_rev &= 0xFF;
+
+        /* May be a later chip in disguise. Check */
+        /* Newer chips are not in the HPT36x driver. Ignore them */
+        if (class_rev > 2)
+                        return -ENODEV;
+
+        pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
+        pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
+        pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
+        pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
+
+        pci_read_config_byte(dev, 0x51, &drive_fast);
+        if (drive_fast & 0x80)
+                pci_write_config_byte(dev, 0x51, drive_fast & ~0x80);
+
+        pci_read_config_dword(dev, 0x40,  &reg1);
+
+        /* PCI clocking determines the ATA timing values to use */
+        /* info_hpt366 is safe against re-entry so we can scribble on it */
+        switch(reg1 & 0x700) {
+                case 5:
+                        info_hpt366.private_data = &hpt366_40;
+                        break;
+                case 9:
+                        info_hpt366.private_data = &hpt366_25;
+                        break;
+                default:
+                        info_hpt366.private_data = &hpt366_33;
+                        break;
+        }
+        /* Now kick off ATA set up */
+        return ata_pci_init_one(dev, port_info, 2);
+}
+
+static struct pci_device_id hpt36x[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366), },
+        { 0, },
+};
+
+static struct pci_driver hpt36x_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = hpt36x,
+        .probe          = hpt36x_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init hpt36x_init(void)
+{
+        return pci_register_driver(&hpt36x_pci_driver);
+}
+
+
+static void __exit hpt36x_exit(void)
+{
+        pci_unregister_driver(&hpt36x_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for the Highpoint HPT366/368");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, hpt36x);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(hpt36x_init);
+module_exit(hpt36x_exit);
diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c
new file mode 100644
index 000000000000..532a7928f803
--- /dev/null
+++ b/drivers/ata/pata_hpt37x.c
@@ -0,0 +1,1257 @@
+/*
+ * Libata driver for the highpoint 37x and 30x UDMA66 ATA controllers.
+ *
+ * This driver is heavily based upon:
+ *
+ * linux/drivers/ide/pci/hpt366.c               Version 0.36    April 25, 2003
+ *
+ * Copyright (C) 1999-2003              Andre Hedrick <andre@linux-ide.org>
+ * Portions Copyright (C) 2001          Sun Microsystems, Inc.
+ * Portions Copyright (C) 2003          Red Hat Inc
+ *
+ * TODO
+ *      PLL mode
+ *      Look into engine reset on timeout errors. Should not be
+ *              required.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME        "pata_hpt37x"
+#define DRV_VERSION     "0.5"
+
+struct hpt_clock {
+        u8      xfer_speed;
+        u32     timing;
+};
+
+struct hpt_chip {
+        const char *name;
+        unsigned int base;
+        struct hpt_clock const *clocks[4];
+};
+
+/* key for bus clock timings
+ * bit
+ * 0:3    data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
+ *        DMA. cycles = value + 1
+ * 4:8    data_low_time. active time of DIOW_/DIOR_ for PIO and MW
+ *        DMA. cycles = value + 1
+ * 9:12   cmd_high_time. inactive time of DIOW_/DIOR_ during task file
+ *        register access.
+ * 13:17  cmd_low_time. active time of DIOW_/DIOR_ during task file
+ *        register access.
+ * 18:21  udma_cycle_time. clock freq and clock cycles for UDMA xfer.
+ *        during task file register access.
+ * 22:24  pre_high_time. time to initialize 1st cycle for PIO and MW DMA
+ *        xfer.
+ * 25:27  cmd_pre_high_time. time to initialize 1st PIO cycle for task
+ *        register access.
+ * 28     UDMA enable
+ * 29     DMA enable
+ * 30     PIO_MST enable. if set, the chip is in bus master mode during
+ *        PIO.
+ * 31     FIFO enable.
+ */
+
+/* from highpoint documentation. these are old values */
+static const struct hpt_clock hpt370_timings_33[] = {
+/*      {       XFER_UDMA_5,    0x1A85F442,     0x16454e31      }, */
+        {       XFER_UDMA_5,    0x16454e31      },
+        {       XFER_UDMA_4,    0x16454e31      },
+        {       XFER_UDMA_3,    0x166d4e31      },
+        {       XFER_UDMA_2,    0x16494e31      },
+        {       XFER_UDMA_1,    0x164d4e31      },
+        {       XFER_UDMA_0,    0x16514e31      },
+
+        {       XFER_MW_DMA_2,  0x26514e21      },
+        {       XFER_MW_DMA_1,  0x26514e33      },
+        {       XFER_MW_DMA_0,  0x26514e97      },
+
+        {       XFER_PIO_4,     0x06514e21      },
+        {       XFER_PIO_3,     0x06514e22      },
+        {       XFER_PIO_2,     0x06514e33      },
+        {       XFER_PIO_1,     0x06914e43      },
+        {       XFER_PIO_0,     0x06914e57      },
+        {       0,              0x06514e57      }
+};
+
+static const struct hpt_clock hpt370_timings_66[] = {
+        {       XFER_UDMA_5,    0x14846231      },
+        {       XFER_UDMA_4,    0x14886231      },
+        {       XFER_UDMA_3,    0x148c6231      },
+        {       XFER_UDMA_2,    0x148c6231      },
+        {       XFER_UDMA_1,    0x14906231      },
+        {       XFER_UDMA_0,    0x14986231      },
+
+        {       XFER_MW_DMA_2,  0x26514e21      },
+        {       XFER_MW_DMA_1,  0x26514e33      },
+        {       XFER_MW_DMA_0,  0x26514e97      },
+
+        {       XFER_PIO_4,     0x06514e21      },
+        {       XFER_PIO_3,     0x06514e22      },
+        {       XFER_PIO_2,     0x06514e33      },
+        {       XFER_PIO_1,     0x06914e43      },
+        {       XFER_PIO_0,     0x06914e57      },
+        {       0,              0x06514e57      }
+};
+
+/* these are the current (4 sep 2001) timings from highpoint */
+static const struct hpt_clock hpt370a_timings_33[] = {
+        {       XFER_UDMA_5,    0x12446231      },
+        {       XFER_UDMA_4,    0x12446231      },
+        {       XFER_UDMA_3,    0x126c6231      },
+        {       XFER_UDMA_2,    0x12486231      },
+        {       XFER_UDMA_1,    0x124c6233      },
+        {       XFER_UDMA_0,    0x12506297      },
+
+        {       XFER_MW_DMA_2,  0x22406c31      },
+        {       XFER_MW_DMA_1,  0x22406c33      },
+        {       XFER_MW_DMA_0,  0x22406c97      },
+
+        {       XFER_PIO_4,     0x06414e31      },
+        {       XFER_PIO_3,     0x06414e42      },
+        {       XFER_PIO_2,     0x06414e53      },
+        {       XFER_PIO_1,     0x06814e93      },
+        {       XFER_PIO_0,     0x06814ea7      },
+        {       0,              0x06814ea7      }
+};
+
+/* 2x 33MHz timings */
+static const struct hpt_clock hpt370a_timings_66[] = {
+        {       XFER_UDMA_5,    0x1488e673      },
+        {       XFER_UDMA_4,    0x1488e673      },
+        {       XFER_UDMA_3,    0x1498e673      },
+        {       XFER_UDMA_2,    0x1490e673      },
+        {       XFER_UDMA_1,    0x1498e677      },
+        {       XFER_UDMA_0,    0x14a0e73f      },
+
+        {       XFER_MW_DMA_2,  0x2480fa73      },
+        {       XFER_MW_DMA_1,  0x2480fa77      },
+        {       XFER_MW_DMA_0,  0x2480fb3f      },
+
+        {       XFER_PIO_4,     0x0c82be73      },
+        {       XFER_PIO_3,     0x0c82be95      },
+        {       XFER_PIO_2,     0x0c82beb7      },
+        {       XFER_PIO_1,     0x0d02bf37      },
+        {       XFER_PIO_0,     0x0d02bf5f      },
+        {       0,              0x0d02bf5f      }
+};
+
+static const struct hpt_clock hpt370a_timings_50[] = {
+        {       XFER_UDMA_5,    0x12848242      },
+        {       XFER_UDMA_4,    0x12ac8242      },
+        {       XFER_UDMA_3,    0x128c8242      },
+        {       XFER_UDMA_2,    0x120c8242      },
+        {       XFER_UDMA_1,    0x12148254      },
+        {       XFER_UDMA_0,    0x121882ea      },
+
+        {       XFER_MW_DMA_2,  0x22808242      },
+        {       XFER_MW_DMA_1,  0x22808254      },
+        {       XFER_MW_DMA_0,  0x228082ea      },
+
+        {       XFER_PIO_4,     0x0a81f442      },
+        {       XFER_PIO_3,     0x0a81f443      },
+        {       XFER_PIO_2,     0x0a81f454      },
+        {       XFER_PIO_1,     0x0ac1f465      },
+        {       XFER_PIO_0,     0x0ac1f48a      },
+        {       0,              0x0ac1f48a      }
+};
+
+static const struct hpt_clock hpt372_timings_33[] = {
+        {       XFER_UDMA_6,    0x1c81dc62      },
+        {       XFER_UDMA_5,    0x1c6ddc62      },
+        {       XFER_UDMA_4,    0x1c8ddc62      },
+        {       XFER_UDMA_3,    0x1c8edc62      },      /* checkme */
+        {       XFER_UDMA_2,    0x1c91dc62      },
+        {       XFER_UDMA_1,    0x1c9adc62      },      /* checkme */
+        {       XFER_UDMA_0,    0x1c82dc62      },      /* checkme */
+
+        {       XFER_MW_DMA_2,  0x2c829262      },
+        {       XFER_MW_DMA_1,  0x2c829266      },      /* checkme */
+        {       XFER_MW_DMA_0,  0x2c82922e      },      /* checkme */
+
+        {       XFER_PIO_4,     0x0c829c62      },
+        {       XFER_PIO_3,     0x0c829c84      },
+        {       XFER_PIO_2,     0x0c829ca6      },
+        {       XFER_PIO_1,     0x0d029d26      },
+        {       XFER_PIO_0,     0x0d029d5e      },
+        {       0,              0x0d029d5e      }
+};
+
+static const struct hpt_clock hpt372_timings_50[] = {
+        {       XFER_UDMA_5,    0x12848242      },
+        {       XFER_UDMA_4,    0x12ac8242      },
+        {       XFER_UDMA_3,    0x128c8242      },
+        {       XFER_UDMA_2,    0x120c8242      },
+        {       XFER_UDMA_1,    0x12148254      },
+        {       XFER_UDMA_0,    0x121882ea      },
+
+        {       XFER_MW_DMA_2,  0x22808242      },
+        {       XFER_MW_DMA_1,  0x22808254      },
+        {       XFER_MW_DMA_0,  0x228082ea      },
+
+        {       XFER_PIO_4,     0x0a81f442      },
+        {       XFER_PIO_3,     0x0a81f443      },
+        {       XFER_PIO_2,     0x0a81f454      },
+        {       XFER_PIO_1,     0x0ac1f465      },
+        {       XFER_PIO_0,     0x0ac1f48a      },
+        {       0,              0x0a81f443      }
+};
+
+static const struct hpt_clock hpt372_timings_66[] = {
+        {       XFER_UDMA_6,    0x1c869c62      },
+        {       XFER_UDMA_5,    0x1cae9c62      },
+        {       XFER_UDMA_4,    0x1c8a9c62      },
+        {       XFER_UDMA_3,    0x1c8e9c62      },
+        {       XFER_UDMA_2,    0x1c929c62      },
+        {       XFER_UDMA_1,    0x1c9a9c62      },
+        {       XFER_UDMA_0,    0x1c829c62      },
+
+        {       XFER_MW_DMA_2,  0x2c829c62      },
+        {       XFER_MW_DMA_1,  0x2c829c66      },
+        {       XFER_MW_DMA_0,  0x2c829d2e      },
+
+        {       XFER_PIO_4,     0x0c829c62      },
+        {       XFER_PIO_3,     0x0c829c84      },
+        {       XFER_PIO_2,     0x0c829ca6      },
+        {       XFER_PIO_1,     0x0d029d26      },
+        {       XFER_PIO_0,     0x0d029d5e      },
+        {       0,              0x0d029d26      }
+};
+
+static const struct hpt_clock hpt374_timings_33[] = {
+        {       XFER_UDMA_6,    0x12808242      },
+        {       XFER_UDMA_5,    0x12848242      },
+        {       XFER_UDMA_4,    0x12ac8242      },
+        {       XFER_UDMA_3,    0x128c8242      },
+        {       XFER_UDMA_2,    0x120c8242      },
+        {       XFER_UDMA_1,    0x12148254      },
+        {       XFER_UDMA_0,    0x121882ea      },
+
+        {       XFER_MW_DMA_2,  0x22808242      },
+        {       XFER_MW_DMA_1,  0x22808254      },
+        {       XFER_MW_DMA_0,  0x228082ea      },
+
+        {       XFER_PIO_4,     0x0a81f442      },
+        {       XFER_PIO_3,     0x0a81f443      },
+        {       XFER_PIO_2,     0x0a81f454      },
+        {       XFER_PIO_1,     0x0ac1f465      },
+        {       XFER_PIO_0,     0x0ac1f48a      },
+        {       0,              0x06814e93      }
+};
+
+static const struct hpt_chip hpt370 = {
+        "HPT370",
+        48,
+        {
+                hpt370_timings_33,
+                NULL,
+                NULL,
+                hpt370_timings_66
+        }
+};
+
+static const struct hpt_chip hpt370a = {
+        "HPT370A",
+        48,
+        {
+                hpt370a_timings_33,
+                NULL,
+                hpt370a_timings_50,
+                hpt370a_timings_66
+        }
+};
+
+static const struct hpt_chip hpt372 = {
+        "HPT372",
+        55,
+        {
+                hpt372_timings_33,
+                NULL,
+                hpt372_timings_50,
+                hpt372_timings_66
+        }
+};
+
+static const struct hpt_chip hpt302 = {
+        "HPT302",
+        66,
+        {
+                hpt372_timings_33,
+                NULL,
+                hpt372_timings_50,
+                hpt372_timings_66
+        }
+};
+
+static const struct hpt_chip hpt371 = {
+        "HPT371",
+        66,
+        {
+                hpt372_timings_33,
+                NULL,
+                hpt372_timings_50,
+                hpt372_timings_66
+        }
+};
+
+static const struct hpt_chip hpt372a = {
+        "HPT372A",
+        66,
+        {
+                hpt372_timings_33,
+                NULL,
+                hpt372_timings_50,
+                hpt372_timings_66
+        }
+};
+
+static const struct hpt_chip hpt374 = {
+        "HPT374",
+        48,
+        {
+                hpt374_timings_33,
+                NULL,
+                NULL,
+                NULL
+        }
+};
+
+/**
+ *      hpt37x_find_mode        -       reset the hpt37x bus
+ *      @ap: ATA port
+ *      @speed: transfer mode
+ *
+ *      Return the 32bit register programming information for this channel
+ *      that matches the speed provided.
+ */
+
+static u32 hpt37x_find_mode(struct ata_port *ap, int speed)
+{
+        struct hpt_clock *clocks = ap->host->private_data;
+
+        while(clocks->xfer_speed) {
+                if (clocks->xfer_speed == speed)
+                        return clocks->timing;
+                clocks++;
+        }
+        BUG();
+        return 0xffffffffU;     /* silence compiler warning */
+}
+
+static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr, const char *list[])
+{
+        unsigned char model_num[40];
+        char *s;
+        unsigned int len;
+        int i = 0;
+
+        ata_id_string(dev->id, model_num, ATA_ID_PROD_OFS,
+                          sizeof(model_num));
+        s = &model_num[0];
+        len = strnlen(s, sizeof(model_num));
+
+        /* ATAPI specifies that empty space is blank-filled; remove blanks */
+        while ((len > 0) && (s[len - 1] == ' ')) {
+                len--;
+                s[len] = 0;
+        }
+
+        while(list[i] != NULL) {
+                if (!strncmp(list[i], s, len)) {
+                        printk(KERN_WARNING DRV_NAME ": %s is not supported for %s.\n",
+                                modestr, list[i]);
+                        return 1;
+                }
+                i++;
+        }
+        return 0;
+}
+
+static const char *bad_ata33[] = {
+        "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", "Maxtor 90845U3", "Maxtor 90650U2",
+        "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2",
+        "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4",
+        "Maxtor 90510D4",
+        "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2",
+        "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4",
+        "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2",
+        NULL
+};
+
+static const char *bad_ata100_5[] = {
+        "IBM-DTLA-307075",
+        "IBM-DTLA-307060",
+        "IBM-DTLA-307045",
+        "IBM-DTLA-307030",
+        "IBM-DTLA-307020",
+        "IBM-DTLA-307015",
+        "IBM-DTLA-305040",
+        "IBM-DTLA-305030",
+        "IBM-DTLA-305020",
+        "IC35L010AVER07-0",
+        "IC35L020AVER07-0",
+        "IC35L030AVER07-0",
+        "IC35L040AVER07-0",
+        "IC35L060AVER07-0",
+        "WDC AC310200R",
+        NULL
+};
+
+/**
+ *      hpt370_filter   -       mode selection filter
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Block UDMA on devices that cause trouble with this controller.
+ */
+
+static unsigned long hpt370_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask)
+{
+        if (adev->class != ATA_DEV_ATA) {
+                if (hpt_dma_blacklisted(adev, "UDMA", bad_ata33))
+                        mask &= ~ATA_MASK_UDMA;
+                if (hpt_dma_blacklisted(adev, "UDMA100", bad_ata100_5))
+                        mask &= ~(0x1F << ATA_SHIFT_UDMA);
+        }
+        return ata_pci_default_filter(ap, adev, mask);
+}
+
+/**
+ *      hpt370a_filter  -       mode selection filter
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Block UDMA on devices that cause trouble with this controller.
+ */
+
+static unsigned long hpt370a_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask)
+{
+        if (adev->class != ATA_DEV_ATA) {
+                if (hpt_dma_blacklisted(adev, "UDMA100", bad_ata100_5))
+                        mask &= ~ (0x1F << ATA_SHIFT_UDMA);
+        }
+        return ata_pci_default_filter(ap, adev, mask);
+}
+
+/**
+ *      hpt37x_pre_reset        -       reset the hpt37x bus
+ *      @ap: ATA port to reset
+ *
+ *      Perform the initial reset handling for the 370/372 and 374 func 0
+ */
+
+static int hpt37x_pre_reset(struct ata_port *ap)
+{
+        u8 scr2, ata66;
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+        pci_read_config_byte(pdev, 0x5B, &scr2);
+        pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01);
+        /* Cable register now active */
+        pci_read_config_byte(pdev, 0x5A, &ata66);
+        /* Restore state */
+        pci_write_config_byte(pdev, 0x5B, scr2);
+
+        if (ata66 & (1 << ap->port_no))
+                ap->cbl = ATA_CBL_PATA40;
+        else
+                ap->cbl = ATA_CBL_PATA80;
+
+        /* Reset the state machine */
+        pci_write_config_byte(pdev, 0x50, 0x37);
+        pci_write_config_byte(pdev, 0x54, 0x37);
+        udelay(100);
+
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      hpt37x_error_handler    -       reset the hpt374
+ *      @ap: ATA port to reset
+ *
+ *      Perform probe for HPT37x, except for HPT374 channel 2
+ */
+
+static void hpt37x_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, hpt37x_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+static int hpt374_pre_reset(struct ata_port *ap)
+{
+        u16 mcr3, mcr6;
+        u8 ata66;
+
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        /* Do the extra channel work */
+        pci_read_config_word(pdev, 0x52, &mcr3);
+        pci_read_config_word(pdev, 0x56, &mcr6);
+        /* Set bit 15 of 0x52 to enable TCBLID as input
+           Set bit 15 of 0x56 to enable FCBLID as input
+         */
+        pci_write_config_word(pdev, 0x52, mcr3 | 0x8000);
+        pci_write_config_word(pdev, 0x56, mcr6 | 0x8000);
+        pci_read_config_byte(pdev, 0x5A, &ata66);
+        /* Reset TCBLID/FCBLID to output */
+        pci_write_config_word(pdev, 0x52, mcr3);
+        pci_write_config_word(pdev, 0x56, mcr6);
+
+        if (ata66 & (1 << ap->port_no))
+                ap->cbl = ATA_CBL_PATA40;
+        else
+                ap->cbl = ATA_CBL_PATA80;
+
+        /* Reset the state machine */
+        pci_write_config_byte(pdev, 0x50, 0x37);
+        pci_write_config_byte(pdev, 0x54, 0x37);
+        udelay(100);
+
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      hpt374_error_handler    -       reset the hpt374
+ *      @classes:
+ *
+ *      The 374 cable detect is a little different due to the extra
+ *      channels. The function 0 channels work like usual but function 1
+ *      is special
+ */
+
+static void hpt374_error_handler(struct ata_port *ap)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+        if (!(PCI_FUNC(pdev->devfn) & 1))
+                hpt37x_error_handler(ap);
+        else
+                ata_bmdma_drive_eh(ap, hpt374_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      hpt370_set_piomode              -       PIO setup
+ *      @ap: ATA interface
+ *      @adev: device on the interface
+ *
+ *      Perform PIO mode setup.
+ */
+
+static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u32 addr1, addr2;
+        u32 reg;
+        u32 mode;
+        u8 fast;
+
+        addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+        addr2 = 0x51 + 4 * ap->port_no;
+
+        /* Fast interrupt prediction disable, hold off interrupt disable */
+        pci_read_config_byte(pdev, addr2, &fast);
+        fast &= ~0x02;
+        fast |= 0x01;
+        pci_write_config_byte(pdev, addr2, fast);
+
+        pci_read_config_dword(pdev, addr1, &reg);
+        mode = hpt37x_find_mode(ap, adev->pio_mode);
+        mode &= ~0x8000000;     /* No FIFO in PIO */
+        mode &= ~0x30070000;    /* Leave config bits alone */
+        reg &= 0x30070000;      /* Strip timing bits */
+        pci_write_config_dword(pdev, addr1, reg | mode);
+}
+
+/**
+ *      hpt370_set_dmamode              -       DMA timing setup
+ *      @ap: ATA interface
+ *      @adev: Device being configured
+ *
+ *      Set up the channel for MWDMA or UDMA modes. Much the same as with
+ *      PIO, load the mode number and then set MWDMA or UDMA flag.
+ */
+
+static void hpt370_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u32 addr1, addr2;
+        u32 reg;
+        u32 mode;
+        u8 fast;
+
+        addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+        addr2 = 0x51 + 4 * ap->port_no;
+
+        /* Fast interrupt prediction disable, hold off interrupt disable */
+        pci_read_config_byte(pdev, addr2, &fast);
+        fast &= ~0x02;
+        fast |= 0x01;
+        pci_write_config_byte(pdev, addr2, fast);
+
+        pci_read_config_dword(pdev, addr1, &reg);
+        mode = hpt37x_find_mode(ap, adev->dma_mode);
+        mode |= 0x8000000;      /* FIFO in MWDMA or UDMA */
+        mode &= ~0xC0000000;    /* Leave config bits alone */
+        reg &= 0xC0000000;      /* Strip timing bits */
+        pci_write_config_dword(pdev, addr1, reg | mode);
+}
+
+/**
+ *      hpt370_bmdma_start              -       DMA engine begin
+ *      @qc: ATA command
+ *
+ *      The 370 and 370A want us to reset the DMA engine each time we
+ *      use it. The 372 and later are fine.
+ */
+
+static void hpt370_bmdma_start(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
+        udelay(10);
+        ata_bmdma_start(qc);
+}
+
+/**
+ *      hpt370_bmdma_end                -       DMA engine stop
+ *      @qc: ATA command
+ *
+ *      Work around the HPT370 DMA engine.
+ */
+
+static void hpt370_bmdma_stop(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u8 dma_stat = inb(ap->ioaddr.bmdma_addr + 2);
+        u8 dma_cmd;
+        unsigned long bmdma = ap->ioaddr.bmdma_addr;
+
+        if (dma_stat & 0x01) {
+                udelay(20);
+                dma_stat = inb(bmdma + 2);
+        }
+        if (dma_stat & 0x01) {
+                /* Clear the engine */
+                pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
+                udelay(10);
+                /* Stop DMA */
+                dma_cmd = inb(bmdma );
+                outb(dma_cmd & 0xFE, bmdma);
+                /* Clear Error */
+                dma_stat = inb(bmdma + 2);
+                outb(dma_stat | 0x06 , bmdma + 2);
+                /* Clear the engine */
+                pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
+                udelay(10);
+        }
+        ata_bmdma_stop(qc);
+}
+
+/**
+ *      hpt372_set_piomode              -       PIO setup
+ *      @ap: ATA interface
+ *      @adev: device on the interface
+ *
+ *      Perform PIO mode setup.
+ */
+
+static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u32 addr1, addr2;
+        u32 reg;
+        u32 mode;
+        u8 fast;
+
+        addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+        addr2 = 0x51 + 4 * ap->port_no;
+
+        /* Fast interrupt prediction disable, hold off interrupt disable */
+        pci_read_config_byte(pdev, addr2, &fast);
+        fast &= ~0x07;
+        pci_write_config_byte(pdev, addr2, fast);
+
+        pci_read_config_dword(pdev, addr1, &reg);
+        mode = hpt37x_find_mode(ap, adev->pio_mode);
+
+        printk("Find mode for %d reports %X\n", adev->pio_mode, mode);
+        mode &= ~0x80000000;    /* No FIFO in PIO */
+        mode &= ~0x30070000;    /* Leave config bits alone */
+        reg &= 0x30070000;      /* Strip timing bits */
+        pci_write_config_dword(pdev, addr1, reg | mode);
+}
+
+/**
+ *      hpt372_set_dmamode              -       DMA timing setup
+ *      @ap: ATA interface
+ *      @adev: Device being configured
+ *
+ *      Set up the channel for MWDMA or UDMA modes. Much the same as with
+ *      PIO, load the mode number and then set MWDMA or UDMA flag.
+ */
+
+static void hpt372_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u32 addr1, addr2;
+        u32 reg;
+        u32 mode;
+        u8 fast;
+
+        addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+        addr2 = 0x51 + 4 * ap->port_no;
+
+        /* Fast interrupt prediction disable, hold off interrupt disable */
+        pci_read_config_byte(pdev, addr2, &fast);
+        fast &= ~0x07;
+        pci_write_config_byte(pdev, addr2, fast);
+
+        pci_read_config_dword(pdev, addr1, &reg);
+        mode = hpt37x_find_mode(ap, adev->dma_mode);
+        printk("Find mode for DMA %d reports %X\n", adev->dma_mode, mode);
+        mode &= ~0xC0000000;    /* Leave config bits alone */
+        mode |= 0x80000000;     /* FIFO in MWDMA or UDMA */
+        reg &= 0xC0000000;      /* Strip timing bits */
+        pci_write_config_dword(pdev, addr1, reg | mode);
+}
+
+/**
+ *      hpt37x_bmdma_end                -       DMA engine stop
+ *      @qc: ATA command
+ *
+ *      Clean up after the HPT372 and later DMA engine
+ */
+
+static void hpt37x_bmdma_stop(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        int mscreg = 0x50 + 2 * ap->port_no;
+        u8 bwsr_stat, msc_stat;
+
+        pci_read_config_byte(pdev, 0x6A, &bwsr_stat);
+        pci_read_config_byte(pdev, mscreg, &msc_stat);
+        if (bwsr_stat & (1 << ap->port_no))
+                pci_write_config_byte(pdev, mscreg, msc_stat | 0x30);
+        ata_bmdma_stop(qc);
+}
+
+
+static struct scsi_host_template hpt37x_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+/*
+ *      Configuration for HPT370
+ */
+
+static struct ata_port_operations hpt370_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = hpt370_set_piomode,
+        .set_dmamode    = hpt370_set_dmamode,
+        .mode_filter    = hpt370_filter,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = hpt37x_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = hpt370_bmdma_start,
+        .bmdma_stop     = hpt370_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/*
+ *      Configuration for HPT370A. Close to 370 but less filters
+ */
+
+static struct ata_port_operations hpt370a_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = hpt370_set_piomode,
+        .set_dmamode    = hpt370_set_dmamode,
+        .mode_filter    = hpt370a_filter,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = hpt37x_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = hpt370_bmdma_start,
+        .bmdma_stop     = hpt370_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/*
+ *      Configuration for HPT372, HPT371, HPT302. Slightly different PIO
+ *      and DMA mode setting functionality.
+ */
+
+static struct ata_port_operations hpt372_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = hpt372_set_piomode,
+        .set_dmamode    = hpt372_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = hpt37x_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = hpt37x_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/*
+ *      Configuration for HPT374. Mode setting works like 372 and friends
+ *      but we have a different cable detection procedure.
+ */
+
+static struct ata_port_operations hpt374_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = hpt372_set_piomode,
+        .set_dmamode    = hpt372_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = hpt374_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = hpt37x_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/**
+ *      htp37x_clock_slot       -       Turn timing to PC clock entry
+ *      @freq: Reported frequency timing
+ *      @base: Base timing
+ *
+ *      Turn the timing data intoa clock slot (0 for 33, 1 for 40, 2 for 50
+ *      and 3 for 66Mhz)
+ */
+
+static int hpt37x_clock_slot(unsigned int freq, unsigned int base)
+{
+        unsigned int f = (base * freq) / 192;   /* Mhz */
+        if (f < 40)
+                return 0;       /* 33Mhz slot */
+        if (f < 45)
+                return 1;       /* 40Mhz slot */
+        if (f < 55)
+                return 2;       /* 50Mhz slot */
+        return 3;               /* 60Mhz slot */
+}
+
+/**
+ *      hpt37x_calibrate_dpll           -       Calibrate the DPLL loop
+ *      @dev: PCI device
+ *
+ *      Perform a calibration cycle on the HPT37x DPLL. Returns 1 if this
+ *      succeeds
+ */
+
+static int hpt37x_calibrate_dpll(struct pci_dev *dev)
+{
+        u8 reg5b;
+        u32 reg5c;
+        int tries;
+
+        for(tries = 0; tries < 0x5000; tries++) {
+                udelay(50);
+                pci_read_config_byte(dev, 0x5b, &reg5b);
+                if (reg5b & 0x80) {
+                        /* See if it stays set */
+                        for(tries = 0; tries < 0x1000; tries ++) {
+                                pci_read_config_byte(dev, 0x5b, &reg5b);
+                                /* Failed ? */
+                                if ((reg5b & 0x80) == 0)
+                                        return 0;
+                        }
+                        /* Turn off tuning, we have the DPLL set */
+                        pci_read_config_dword(dev, 0x5c, &reg5c);
+                        pci_write_config_dword(dev, 0x5c, reg5c & ~ 0x100);
+                        return 1;
+                }
+        }
+        /* Never went stable */
+        return 0;
+}
+/**
+ *      hpt37x_init_one         -       Initialise an HPT37X/302
+ *      @dev: PCI device
+ *      @id: Entry in match table
+ *
+ *      Initialise an HPT37x device. There are some interesting complications
+ *      here. Firstly the chip may report 366 and be one of several variants.
+ *      Secondly all the timings depend on the clock for the chip which we must
+ *      detect and look up
+ *
+ *      This is the known chip mappings. It may be missing a couple of later
+ *      releases.
+ *
+ *      Chip version            PCI             Rev     Notes
+ *      HPT366                  4 (HPT366)      0       Other driver
+ *      HPT366                  4 (HPT366)      1       Other driver
+ *      HPT368                  4 (HPT366)      2       Other driver
+ *      HPT370                  4 (HPT366)      3       UDMA100
+ *      HPT370A                 4 (HPT366)      4       UDMA100
+ *      HPT372                  4 (HPT366)      5       UDMA133 (1)
+ *      HPT372N                 4 (HPT366)      6       Other driver
+ *      HPT372A                 5 (HPT372)      1       UDMA133 (1)
+ *      HPT372N                 5 (HPT372)      2       Other driver
+ *      HPT302                  6 (HPT302)      1       UDMA133
+ *      HPT302N                 6 (HPT302)      2       Other driver
+ *      HPT371                  7 (HPT371)      *       UDMA133
+ *      HPT374                  8 (HPT374)      *       UDMA133 4 channel
+ *      HPT372N                 9 (HPT372N)     *       Other driver
+ *
+ *      (1) UDMA133 support depends on the bus clock
+ */
+
+static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+        /* HPT370 - UDMA100 */
+        static struct ata_port_info info_hpt370 = {
+                .sht = &hpt37x_sht,
+                .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x3f,
+                .port_ops = &hpt370_port_ops
+        };
+        /* HPT370A - UDMA100 */
+        static struct ata_port_info info_hpt370a = {
+                .sht = &hpt37x_sht,
+                .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x3f,
+                .port_ops = &hpt370a_port_ops
+        };
+        /* HPT371, 372 and friends - UDMA133 */
+        static struct ata_port_info info_hpt372 = {
+                .sht = &hpt37x_sht,
+                .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x7f,
+                .port_ops = &hpt372_port_ops
+        };
+        /* HPT371, 372 and friends - UDMA100 at 50MHz clock */
+        static struct ata_port_info info_hpt372_50 = {
+                .sht = &hpt37x_sht,
+                .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x3f,
+                .port_ops = &hpt372_port_ops
+        };
+        /* HPT374 - UDMA133 */
+        static struct ata_port_info info_hpt374 = {
+                .sht = &hpt37x_sht,
+                .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x7f,
+                .port_ops = &hpt374_port_ops
+        };
+
+        static const int MHz[4] = { 33, 40, 50, 66 };
+
+        struct ata_port_info *port_info[2];
+        struct ata_port_info *port;
+
+        u8 irqmask;
+        u32 class_rev;
+        u32 freq;
+
+        const struct hpt_chip *chip_table;
+        int clock_slot;
+
+        pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
+        class_rev &= 0xFF;
+
+        if (dev->device == PCI_DEVICE_ID_TTI_HPT366) {
+                /* May be a later chip in disguise. Check */
+                /* Older chips are in the HPT366 driver. Ignore them */
+                if (class_rev < 3)
+                        return -ENODEV;
+                /* N series chips have their own driver. Ignore */
+                if (class_rev == 6)
+                        return -ENODEV;
+
+                switch(class_rev) {
+                        case 3:
+                                port = &info_hpt370;
+                                chip_table = &hpt370;
+                                break;
+                        case 4:
+                                port = &info_hpt370a;
+                                chip_table = &hpt370a;
+                                break;
+                        case 5:
+                                port = &info_hpt372;
+                                chip_table = &hpt372;
+                                break;
+                        default:
+                                printk(KERN_ERR "pata_hpt37x: Unknown HPT366 subtype please report (%d).\n", class_rev);
+                                return -ENODEV;
+                }
+        } else {
+                switch(dev->device) {
+                        case PCI_DEVICE_ID_TTI_HPT372:
+                                /* 372N if rev >= 2*/
+                                if (class_rev >= 2)
+                                        return -ENODEV;
+                                port = &info_hpt372;
+                                chip_table = &hpt372a;
+                                break;
+                        case PCI_DEVICE_ID_TTI_HPT302:
+                                /* 302N if rev > 1 */
+                                if (class_rev > 1)
+                                        return -ENODEV;
+                                port = &info_hpt372;
+                                /* Check this */
+                                chip_table = &hpt302;
+                                break;
+                        case PCI_DEVICE_ID_TTI_HPT371:
+                                port = &info_hpt372;
+                                chip_table = &hpt371;
+                                break;
+                        case PCI_DEVICE_ID_TTI_HPT374:
+                                chip_table = &hpt374;
+                                port = &info_hpt374;
+                                break;
+                        default:
+                                printk(KERN_ERR "pata_hpt37x: PCI table is bogus please report (%d).\n", dev->device);
+                                return -ENODEV;
+                }
+        }
+        /* Ok so this is a chip we support */
+
+        pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
+        pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
+        pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
+        pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
+
+        pci_read_config_byte(dev, 0x5A, &irqmask);
+        irqmask &= ~0x10;
+        pci_write_config_byte(dev, 0x5a, irqmask);
+
+        /*
+         * default to pci clock. make sure MA15/16 are set to output
+         * to prevent drives having problems with 40-pin cables. Needed
+         * for some drives such as IBM-DTLA which will not enter ready
+         * state on reset when PDIAG is a input.
+         */
+
+        pci_write_config_byte(dev, 0x5b, 0x23);
+
+        pci_read_config_dword(dev, 0x70, &freq);
+        if ((freq >> 12) != 0xABCDE) {
+                int i;
+                u8 sr;
+                u32 total = 0;
+
+                printk(KERN_WARNING "pata_hpt37x: BIOS has not set timing clocks.\n");
+
+                /* This is the process the HPT371 BIOS is reported to use */
+                for(i = 0; i < 128; i++) {
+                        pci_read_config_byte(dev, 0x78, &sr);
+                        total += sr;
+                        udelay(15);
+                }
+                freq = total / 128;
+        }
+        freq &= 0x1FF;
+
+        /*
+         *      Turn the frequency check into a band and then find a timing
+         *      table to match it.
+         */
+
+        clock_slot = hpt37x_clock_slot(freq, chip_table->base);
+        if (chip_table->clocks[clock_slot] == NULL) {
+                /*
+                 *      We need to try PLL mode instead
+                 */
+                unsigned int f_low = (MHz[clock_slot] * chip_table->base) / 192;
+                unsigned int f_high = f_low + 2;
+                int adjust;
+
+                for(adjust = 0; adjust < 8; adjust++) {
+                        if (hpt37x_calibrate_dpll(dev))
+                                break;
+                        /* See if it'll settle at a fractionally different clock */
+                        if ((adjust & 3) == 3) {
+                                f_low --;
+                                f_high ++;
+                        }
+                        pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low);
+                }
+                if (adjust == 8) {
+                        printk(KERN_WARNING "hpt37x: DPLL did not stabilize.\n");
+                        return -ENODEV;
+                }
+                /* Check if this works for all cases */
+                port->private_data = (void *)hpt370_timings_66;
+
+                printk(KERN_INFO "hpt37x: Bus clock %dMHz, using DPLL.\n", MHz[clock_slot]);
+        } else {
+                port->private_data = (void *)chip_table->clocks[clock_slot];
+                /*
+                 *      Perform a final fixup. The 371 and 372 clock determines
+                 *      if UDMA133 is available.
+                 */
+
+                if (clock_slot == 2 && chip_table == &hpt372) { /* 50Mhz */
+                        printk(KERN_WARNING "pata_hpt37x: No UDMA133 support available with 50MHz bus clock.\n");
+                        if (port == &info_hpt372)
+                                port = &info_hpt372_50;
+                        else BUG();
+                }
+                printk(KERN_INFO "hpt37x: %s: Bus clock %dMHz.\n", chip_table->name, MHz[clock_slot]);
+        }
+        port_info[0] = port_info[1] = port;
+        /* Now kick off ATA set up */
+        return ata_pci_init_one(dev, port_info, 2);
+}
+
+static struct pci_device_id hpt37x[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366), },
+        { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT371), },
+        { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372), },
+        { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT374), },
+        { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT302), },
+        { 0, },
+};
+
+static struct pci_driver hpt37x_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = hpt37x,
+        .probe          = hpt37x_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init hpt37x_init(void)
+{
+        return pci_register_driver(&hpt37x_pci_driver);
+}
+
+
+static void __exit hpt37x_exit(void)
+{
+        pci_unregister_driver(&hpt37x_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for the Highpoint HPT37x/30x");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, hpt37x);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(hpt37x_init);
+module_exit(hpt37x_exit);
diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
new file mode 100644
index 000000000000..06c8db079b91
--- /dev/null
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -0,0 +1,597 @@
+/*
+ * Libata driver for the highpoint 372N and 302N UDMA66 ATA controllers.
+ *
+ * This driver is heavily based upon:
+ *
+ * linux/drivers/ide/pci/hpt366.c               Version 0.36    April 25, 2003
+ *
+ * Copyright (C) 1999-2003              Andre Hedrick <andre@linux-ide.org>
+ * Portions Copyright (C) 2001          Sun Microsystems, Inc.
+ * Portions Copyright (C) 2003          Red Hat Inc
+ *
+ *
+ * TODO
+ *      371N
+ *      Work out best PLL policy
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME        "pata_hpt3x2n"
+#define DRV_VERSION     "0.3"
+
+enum {
+        HPT_PCI_FAST    =       (1 << 31),
+        PCI66           =       (1 << 1),
+        USE_DPLL        =       (1 << 0)
+};
+
+struct hpt_clock {
+        u8      xfer_speed;
+        u32     timing;
+};
+
+struct hpt_chip {
+        const char *name;
+        struct hpt_clock *clocks[3];
+};
+
+/* key for bus clock timings
+ * bit
+ * 0:3    data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
+ *        DMA. cycles = value + 1
+ * 4:8    data_low_time. active time of DIOW_/DIOR_ for PIO and MW
+ *        DMA. cycles = value + 1
+ * 9:12   cmd_high_time. inactive time of DIOW_/DIOR_ during task file
+ *        register access.
+ * 13:17  cmd_low_time. active time of DIOW_/DIOR_ during task file
+ *        register access.
+ * 18:21  udma_cycle_time. clock freq and clock cycles for UDMA xfer.
+ *        during task file register access.
+ * 22:24  pre_high_time. time to initialize 1st cycle for PIO and MW DMA
+ *        xfer.
+ * 25:27  cmd_pre_high_time. time to initialize 1st PIO cycle for task
+ *        register access.
+ * 28     UDMA enable
+ * 29     DMA enable
+ * 30     PIO_MST enable. if set, the chip is in bus master mode during
+ *        PIO.
+ * 31     FIFO enable.
+ */
+
+/* 66MHz DPLL clocks */
+
+static struct hpt_clock hpt3x2n_clocks[] = {
+        {       XFER_UDMA_7,    0x1c869c62      },
+        {       XFER_UDMA_6,    0x1c869c62      },
+        {       XFER_UDMA_5,    0x1c8a9c62      },
+        {       XFER_UDMA_4,    0x1c8a9c62      },
+        {       XFER_UDMA_3,    0x1c8e9c62      },
+        {       XFER_UDMA_2,    0x1c929c62      },
+        {       XFER_UDMA_1,    0x1c9a9c62      },
+        {       XFER_UDMA_0,    0x1c829c62      },
+
+        {       XFER_MW_DMA_2,  0x2c829c62      },
+        {       XFER_MW_DMA_1,  0x2c829c66      },
+        {       XFER_MW_DMA_0,  0x2c829d2c      },
+
+        {       XFER_PIO_4,     0x0c829c62      },
+        {       XFER_PIO_3,     0x0c829c84      },
+        {       XFER_PIO_2,     0x0c829ca6      },
+        {       XFER_PIO_1,     0x0d029d26      },
+        {       XFER_PIO_0,     0x0d029d5e      },
+        {       0,              0x0d029d5e      }
+};
+
+/**
+ *      hpt3x2n_find_mode       -       reset the hpt3x2n bus
+ *      @ap: ATA port
+ *      @speed: transfer mode
+ *
+ *      Return the 32bit register programming information for this channel
+ *      that matches the speed provided. For the moment the clocks table
+ *      is hard coded but easy to change. This will be needed if we use
+ *      different DPLLs
+ */
+
+static u32 hpt3x2n_find_mode(struct ata_port *ap, int speed)
+{
+        struct hpt_clock *clocks = hpt3x2n_clocks;
+
+        while(clocks->xfer_speed) {
+                if (clocks->xfer_speed == speed)
+                        return clocks->timing;
+                clocks++;
+        }
+        BUG();
+        return 0xffffffffU;     /* silence compiler warning */
+}
+
+/**
+ *      hpt3x2n_pre_reset       -       reset the hpt3x2n bus
+ *      @ap: ATA port to reset
+ *
+ *      Perform the initial reset handling for the 3x2n series controllers.
+ *      Reset the hardware and state machine, obtain the cable type.
+ */
+
+static int hpt3xn_pre_reset(struct ata_port *ap)
+{
+        u8 scr2, ata66;
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+        pci_read_config_byte(pdev, 0x5B, &scr2);
+        pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01);
+        /* Cable register now active */
+        pci_read_config_byte(pdev, 0x5A, &ata66);
+        /* Restore state */
+        pci_write_config_byte(pdev, 0x5B, scr2);
+
+        if (ata66 & (1 << ap->port_no))
+                ap->cbl = ATA_CBL_PATA40;
+        else
+                ap->cbl = ATA_CBL_PATA80;
+
+        /* Reset the state machine */
+        pci_write_config_byte(pdev, 0x50, 0x37);
+        pci_write_config_byte(pdev, 0x54, 0x37);
+        udelay(100);
+
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      hpt3x2n_error_handler   -       probe the hpt3x2n bus
+ *      @ap: ATA port to reset
+ *
+ *      Perform the probe reset handling for the 3x2N
+ */
+
+static void hpt3x2n_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, hpt3xn_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      hpt3x2n_set_piomode             -       PIO setup
+ *      @ap: ATA interface
+ *      @adev: device on the interface
+ *
+ *      Perform PIO mode setup.
+ */
+
+static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u32 addr1, addr2;
+        u32 reg;
+        u32 mode;
+        u8 fast;
+
+        addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+        addr2 = 0x51 + 4 * ap->port_no;
+
+        /* Fast interrupt prediction disable, hold off interrupt disable */
+        pci_read_config_byte(pdev, addr2, &fast);
+        fast &= ~0x07;
+        pci_write_config_byte(pdev, addr2, fast);
+
+        pci_read_config_dword(pdev, addr1, &reg);
+        mode = hpt3x2n_find_mode(ap, adev->pio_mode);
+        mode &= ~0x8000000;     /* No FIFO in PIO */
+        mode &= ~0x30070000;    /* Leave config bits alone */
+        reg &= 0x30070000;      /* Strip timing bits */
+        pci_write_config_dword(pdev, addr1, reg | mode);
+}
+
+/**
+ *      hpt3x2n_set_dmamode             -       DMA timing setup
+ *      @ap: ATA interface
+ *      @adev: Device being configured
+ *
+ *      Set up the channel for MWDMA or UDMA modes. Much the same as with
+ *      PIO, load the mode number and then set MWDMA or UDMA flag.
+ */
+
+static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u32 addr1, addr2;
+        u32 reg;
+        u32 mode;
+        u8 fast;
+
+        addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+        addr2 = 0x51 + 4 * ap->port_no;
+
+        /* Fast interrupt prediction disable, hold off interrupt disable */
+        pci_read_config_byte(pdev, addr2, &fast);
+        fast &= ~0x07;
+        pci_write_config_byte(pdev, addr2, fast);
+
+        pci_read_config_dword(pdev, addr1, &reg);
+        mode = hpt3x2n_find_mode(ap, adev->dma_mode);
+        mode |= 0x8000000;      /* FIFO in MWDMA or UDMA */
+        mode &= ~0xC0000000;    /* Leave config bits alone */
+        reg &= 0xC0000000;      /* Strip timing bits */
+        pci_write_config_dword(pdev, addr1, reg | mode);
+}
+
+/**
+ *      hpt3x2n_bmdma_end               -       DMA engine stop
+ *      @qc: ATA command
+ *
+ *      Clean up after the HPT3x2n and later DMA engine
+ */
+
+static void hpt3x2n_bmdma_stop(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        int mscreg = 0x50 + 2 * ap->port_no;
+        u8 bwsr_stat, msc_stat;
+
+        pci_read_config_byte(pdev, 0x6A, &bwsr_stat);
+        pci_read_config_byte(pdev, mscreg, &msc_stat);
+        if (bwsr_stat & (1 << ap->port_no))
+                pci_write_config_byte(pdev, mscreg, msc_stat | 0x30);
+        ata_bmdma_stop(qc);
+}
+
+/**
+ *      hpt3x2n_set_clock       -       clock control
+ *      @ap: ATA port
+ *      @source: 0x21 or 0x23 for PLL or PCI sourced clock
+ *
+ *      Switch the ATA bus clock between the PLL and PCI clock sources
+ *      while correctly isolating the bus and resetting internal logic
+ *
+ *      We must use the DPLL for
+ *      -       writing
+ *      -       second channel UDMA7 (SATA ports) or higher
+ *      -       66MHz PCI
+ *
+ *      or we will underclock the device and get reduced performance.
+ */
+
+static void hpt3x2n_set_clock(struct ata_port *ap, int source)
+{
+        unsigned long bmdma = ap->ioaddr.bmdma_addr;
+
+        /* Tristate the bus */
+        outb(0x80, bmdma+0x73);
+        outb(0x80, bmdma+0x77);
+
+        /* Switch clock and reset channels */
+        outb(source, bmdma+0x7B);
+        outb(0xC0, bmdma+0x79);
+
+        /* Reset state machines */
+        outb(0x37, bmdma+0x70);
+        outb(0x37, bmdma+0x74);
+
+        /* Complete reset */
+        outb(0x00, bmdma+0x79);
+
+        /* Reconnect channels to bus */
+        outb(0x00, bmdma+0x73);
+        outb(0x00, bmdma+0x77);
+}
+
+/* Check if our partner interface is busy */
+
+static int hpt3x2n_pair_idle(struct ata_port *ap)
+{
+        struct ata_host *host = ap->host;
+        struct ata_port *pair = host->ports[ap->port_no ^ 1];
+
+        if (pair->hsm_task_state == HSM_ST_IDLE)
+                return 1;
+        return 0;
+}
+
+static int hpt3x2n_use_dpll(struct ata_port *ap, int reading)
+{
+        long flags = (long)ap->host->private_data;
+        /* See if we should use the DPLL */
+        if (reading == 0)
+                return USE_DPLL;        /* Needed for write */
+        if (flags & PCI66)
+                return USE_DPLL;        /* Needed at 66Mhz */
+        return 0;
+}
+
+static unsigned int hpt3x2n_qc_issue_prot(struct ata_queued_cmd *qc)
+{
+        struct ata_taskfile *tf = &qc->tf;
+        struct ata_port *ap = qc->ap;
+        int flags = (long)ap->host->private_data;
+
+        if (hpt3x2n_pair_idle(ap)) {
+                int dpll = hpt3x2n_use_dpll(ap, (tf->flags & ATA_TFLAG_WRITE));
+                if ((flags & USE_DPLL) != dpll) {
+                        if (dpll == 1)
+                                hpt3x2n_set_clock(ap, 0x21);
+                        else
+                                hpt3x2n_set_clock(ap, 0x23);
+                }
+        }
+        return ata_qc_issue_prot(qc);
+}
+
+static struct scsi_host_template hpt3x2n_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+/*
+ *      Configuration for HPT3x2n.
+ */
+
+static struct ata_port_operations hpt3x2n_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = hpt3x2n_set_piomode,
+        .set_dmamode    = hpt3x2n_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = hpt3x2n_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = hpt3x2n_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = hpt3x2n_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/**
+ *      hpt3xn_calibrate_dpll           -       Calibrate the DPLL loop
+ *      @dev: PCI device
+ *
+ *      Perform a calibration cycle on the HPT3xN DPLL. Returns 1 if this
+ *      succeeds
+ */
+
+static int hpt3xn_calibrate_dpll(struct pci_dev *dev)
+{
+        u8 reg5b;
+        u32 reg5c;
+        int tries;
+
+        for(tries = 0; tries < 0x5000; tries++) {
+                udelay(50);
+                pci_read_config_byte(dev, 0x5b, &reg5b);
+                if (reg5b & 0x80) {
+                        /* See if it stays set */
+                        for(tries = 0; tries < 0x1000; tries ++) {
+                                pci_read_config_byte(dev, 0x5b, &reg5b);
+                                /* Failed ? */
+                                if ((reg5b & 0x80) == 0)
+                                        return 0;
+                        }
+                        /* Turn off tuning, we have the DPLL set */
+                        pci_read_config_dword(dev, 0x5c, &reg5c);
+                        pci_write_config_dword(dev, 0x5c, reg5c & ~ 0x100);
+                        return 1;
+                }
+        }
+        /* Never went stable */
+        return 0;
+}
+
+static int hpt3x2n_pci_clock(struct pci_dev *pdev)
+{
+        unsigned long freq;
+        u32 fcnt;
+
+        pci_read_config_dword(pdev, 0x70/*CHECKME*/, &fcnt);
+        if ((fcnt >> 12) != 0xABCDE) {
+                printk(KERN_WARNING "hpt3xn: BIOS clock data not set.\n");
+                return 33;      /* Not BIOS set */
+        }
+        fcnt &= 0x1FF;
+
+        freq = (fcnt * 77) / 192;
+
+        /* Clamp to bands */
+        if (freq < 40)
+                return 33;
+        if (freq < 45)
+                return 40;
+        if (freq < 55)
+                return 50;
+        return 66;
+}
+
+/**
+ *      hpt3x2n_init_one                -       Initialise an HPT37X/302
+ *      @dev: PCI device
+ *      @id: Entry in match table
+ *
+ *      Initialise an HPT3x2n device. There are some interesting complications
+ *      here. Firstly the chip may report 366 and be one of several variants.
+ *      Secondly all the timings depend on the clock for the chip which we must
+ *      detect and look up
+ *
+ *      This is the known chip mappings. It may be missing a couple of later
+ *      releases.
+ *
+ *      Chip version            PCI             Rev     Notes
+ *      HPT372                  4 (HPT366)      5       Other driver
+ *      HPT372N                 4 (HPT366)      6       UDMA133
+ *      HPT372                  5 (HPT372)      1       Other driver
+ *      HPT372N                 5 (HPT372)      2       UDMA133
+ *      HPT302                  6 (HPT302)      *       Other driver
+ *      HPT302N                 6 (HPT302)      > 1     UDMA133
+ *      HPT371                  7 (HPT371)      *       Other driver
+ *      HPT371N                 7 (HPT371)      > 1     UDMA133
+ *      HPT374                  8 (HPT374)      *       Other driver
+ *      HPT372N                 9 (HPT372N)     *       UDMA133
+ *
+ *      (1) UDMA133 support depends on the bus clock
+ *
+ *      To pin down             HPT371N
+ */
+
+static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+        /* HPT372N and friends - UDMA133 */
+        static struct ata_port_info info = {
+                .sht = &hpt3x2n_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x7f,
+                .port_ops = &hpt3x2n_port_ops
+        };
+        struct ata_port_info *port_info[2];
+        struct ata_port_info *port = &info;
+
+        u8 irqmask;
+        u32 class_rev;
+
+        unsigned int pci_mhz;
+        unsigned int f_low, f_high;
+        int adjust;
+
+        pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
+        class_rev &= 0xFF;
+
+        switch(dev->device) {
+                case PCI_DEVICE_ID_TTI_HPT366:
+                        if (class_rev < 6)
+                                return -ENODEV;
+                        break;
+                case PCI_DEVICE_ID_TTI_HPT372:
+                        /* 372N if rev >= 1*/
+                        if (class_rev == 0)
+                                return -ENODEV;
+                        break;
+                case PCI_DEVICE_ID_TTI_HPT302:
+                        if (class_rev < 2)
+                                return -ENODEV;
+                        break;
+                case PCI_DEVICE_ID_TTI_HPT372N:
+                        break;
+                default:
+                        printk(KERN_ERR "pata_hpt3x2n: PCI table is bogus please report (%d).\n", dev->device);
+                        return -ENODEV;
+        }
+
+        /* Ok so this is a chip we support */
+
+        pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
+        pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
+        pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
+        pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
+
+        pci_read_config_byte(dev, 0x5A, &irqmask);
+        irqmask &= ~0x10;
+        pci_write_config_byte(dev, 0x5a, irqmask);
+
+        /* Tune the PLL. HPT recommend using 75 for SATA, 66 for UDMA133 or
+           50 for UDMA100. Right now we always use 66 */
+
+        pci_mhz = hpt3x2n_pci_clock(dev);
+
+        f_low = (pci_mhz * 48) / 66;    /* PCI Mhz for 66Mhz DPLL */
+        f_high = f_low + 2;             /* Tolerance */
+
+        pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low | 0x100);
+        /* PLL clock */
+        pci_write_config_byte(dev, 0x5B, 0x21);
+
+        /* Unlike the 37x we don't try jiggling the frequency */
+        for(adjust = 0; adjust < 8; adjust++) {
+                if (hpt3xn_calibrate_dpll(dev))
+                        break;
+                pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low);
+        }
+        if (adjust == 8)
+                printk(KERN_WARNING "hpt3xn: DPLL did not stabilize.\n");
+
+        /* Set our private data up. We only need a few flags so we use
+           it directly */
+        port->private_data = NULL;
+        if (pci_mhz > 60)
+                port->private_data = (void *)PCI66;
+
+        /* Now kick off ATA set up */
+        port_info[0] = port_info[1] = port;
+        return ata_pci_init_one(dev, port_info, 2);
+}
+
+static struct pci_device_id hpt3x2n[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366), },
+        { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372), },
+        { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT302), },
+        { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372N), },
+        { 0, },
+};
+
+static struct pci_driver hpt3x2n_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = hpt3x2n,
+        .probe          = hpt3x2n_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init hpt3x2n_init(void)
+{
+        return pci_register_driver(&hpt3x2n_pci_driver);
+}
+
+
+static void __exit hpt3x2n_exit(void)
+{
+        pci_unregister_driver(&hpt3x2n_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for the Highpoint HPT3x2n/30x");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, hpt3x2n);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(hpt3x2n_init);
+module_exit(hpt3x2n_exit);
diff --git a/drivers/ata/pata_hpt3x3.c b/drivers/ata/pata_hpt3x3.c
new file mode 100644
index 000000000000..152770133ab1
--- /dev/null
+++ b/drivers/ata/pata_hpt3x3.c
@@ -0,0 +1,226 @@
+/*
+ *      pata_hpt3x3             -       HPT3x3 driver
+ *      (c) Copyright 2005-2006 Red Hat
+ *
+ *      Was pata_hpt34x but the naming was confusing as it supported the
+ *      343 and 363 so it has been renamed.
+ *
+ *      Based on:
+ *      linux/drivers/ide/pci/hpt34x.c          Version 0.40    Sept 10, 2002
+ *      Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
+ *
+ *      May be copied or modified under the terms of the GNU General Public
+ *      License
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME        "pata_hpt3x3"
+#define DRV_VERSION     "0.4.1"
+
+static int hpt3x3_probe_init(struct ata_port *ap)
+{
+        ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      hpt3x3_probe_reset      -       reset the hpt3x3 bus
+ *      @ap: ATA port to reset
+ *
+ *      Perform the housekeeping when doing an ATA bus reeset. We just
+ *      need to force the cable type.
+ */
+
+static void hpt3x3_error_handler(struct ata_port *ap)
+{
+        return ata_bmdma_drive_eh(ap, hpt3x3_probe_init, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      hpt3x3_set_piomode              -       PIO setup
+ *      @ap: ATA interface
+ *      @adev: device on the interface
+ *
+ *      Set our PIO requirements. This is fairly simple on the HPT3x3 as
+ *      all we have to do is clear the MWDMA and UDMA bits then load the
+ *      mode number.
+ */
+
+static void hpt3x3_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u32 r1, r2;
+        int dn = 2 * ap->port_no + adev->devno;
+
+        pci_read_config_dword(pdev, 0x44, &r1);
+        pci_read_config_dword(pdev, 0x48, &r2);
+        /* Load the PIO timing number */
+        r1 &= ~(7 << (3 * dn));
+        r1 |= (adev->pio_mode - XFER_PIO_0) << (3 * dn);
+        r2 &= ~(0x11 << dn);    /* Clear MWDMA and UDMA bits */
+
+        pci_write_config_dword(pdev, 0x44, r1);
+        pci_write_config_dword(pdev, 0x48, r2);
+}
+
+/**
+ *      hpt3x3_set_dmamode              -       DMA timing setup
+ *      @ap: ATA interface
+ *      @adev: Device being configured
+ *
+ *      Set up the channel for MWDMA or UDMA modes. Much the same as with
+ *      PIO, load the mode number and then set MWDMA or UDMA flag.
+ */
+
+static void hpt3x3_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u32 r1, r2;
+        int dn = 2 * ap->port_no + adev->devno;
+        int mode_num = adev->dma_mode & 0x0F;
+
+        pci_read_config_dword(pdev, 0x44, &r1);
+        pci_read_config_dword(pdev, 0x48, &r2);
+        /* Load the timing number */
+        r1 &= ~(7 << (3 * dn));
+        r1 |= (mode_num << (3 * dn));
+        r2 &= ~(0x11 << dn);    /* Clear MWDMA and UDMA bits */
+
+        if (adev->dma_mode >= XFER_UDMA_0)
+                r2 |= 0x01 << dn;       /* Ultra mode */
+        else
+                r2 |= 0x10 << dn;       /* MWDMA */
+
+        pci_write_config_dword(pdev, 0x44, r1);
+        pci_write_config_dword(pdev, 0x48, r2);
+}
+
+static struct scsi_host_template hpt3x3_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations hpt3x3_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = hpt3x3_set_piomode,
+        .set_dmamode    = hpt3x3_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = hpt3x3_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/**
+ *      hpt3x3_init_one         -       Initialise an HPT343/363
+ *      @dev: PCI device
+ *      @id: Entry in match table
+ *
+ *      Perform basic initialisation. The chip has a quirk that it won't
+ *      function unless it is at XX00. The old ATA driver touched this up
+ *      but we leave it for pci quirks to do properly.
+ */
+
+static int hpt3x3_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+        static struct ata_port_info info = {
+                .sht = &hpt3x3_sht,
+                .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x07,
+                .port_ops = &hpt3x3_port_ops
+        };
+        static struct ata_port_info *port_info[2] = { &info, &info };
+        u16 cmd;
+
+        /* Initialize the board */
+        pci_write_config_word(dev, 0x80, 0x00);
+        /* Check if it is a 343 or a 363. 363 has COMMAND_MEMORY set */
+        pci_read_config_word(dev, PCI_COMMAND, &cmd);
+        if (cmd & PCI_COMMAND_MEMORY)
+                pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0xF0);
+        else
+                pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20);
+
+        /* Now kick off ATA set up */
+        return ata_pci_init_one(dev, port_info, 2);
+}
+
+static struct pci_device_id hpt3x3[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT343), },
+        { 0, },
+};
+
+static struct pci_driver hpt3x3_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = hpt3x3,
+        .probe          = hpt3x3_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init hpt3x3_init(void)
+{
+        return pci_register_driver(&hpt3x3_pci_driver);
+}
+
+
+static void __exit hpt3x3_exit(void)
+{
+        pci_unregister_driver(&hpt3x3_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for the Highpoint HPT343/363");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, hpt3x3);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(hpt3x3_init);
+module_exit(hpt3x3_exit);
diff --git a/drivers/ata/pata_isapnp.c b/drivers/ata/pata_isapnp.c
new file mode 100644
index 000000000000..73948c8b7270
--- /dev/null
+++ b/drivers/ata/pata_isapnp.c
@@ -0,0 +1,156 @@
+
+/*
+ *   pata-isapnp.c - ISA PnP PATA controller driver.
+ *   Copyright 2005/2006 Red Hat Inc <alan@redhat.com>, all rights reserved.
+ *
+ *   Based in part on ide-pnp.c by Andrey Panin <pazke@donpac.ru>
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/isapnp.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/ata.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_isapnp"
+#define DRV_VERSION "0.1.5"
+
+static struct scsi_host_template isapnp_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations isapnp_port_ops = {
+        .port_disable   = ata_port_disable,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = ata_bmdma_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/**
+ *      isapnp_init_one         -       attach an isapnp interface
+ *      @idev: PnP device
+ *      @dev_id: matching detect line
+ *
+ *      Register an ISA bus IDE interface. Such interfaces are PIO 0 and
+ *      non shared IRQ.
+ */
+
+static int isapnp_init_one(struct pnp_dev *idev, const struct pnp_device_id *dev_id)
+{
+        struct ata_probe_ent ae;
+
+        if (pnp_port_valid(idev, 0) == 0)
+                return -ENODEV;
+
+        /* FIXME: Should selected polled PIO here not fail */
+        if (pnp_irq_valid(idev, 0) == 0)
+                return -ENODEV;
+
+        memset(&ae, 0, sizeof(struct ata_probe_ent));
+        INIT_LIST_HEAD(&ae.node);
+        ae.dev = &idev->dev;
+        ae.port_ops = &isapnp_port_ops;
+        ae.sht = &isapnp_sht;
+        ae.n_ports = 1;
+        ae.pio_mask = 1;                /* ISA so PIO 0 cycles */
+        ae.irq = pnp_irq(idev, 0);
+        ae.irq_flags = 0;
+        ae.port_flags = ATA_FLAG_SLAVE_POSS;
+        ae.port[0].cmd_addr = pnp_port_start(idev, 0);
+
+        if (pnp_port_valid(idev, 1) == 0) {
+                ae.port[0].altstatus_addr = pnp_port_start(idev, 1);
+                ae.port[0].ctl_addr = pnp_port_start(idev, 1);
+                ae.port_flags |= ATA_FLAG_SRST;
+        }
+        ata_std_ports(&ae.port[0]);
+
+        if (ata_device_add(&ae) == 0)
+                return -ENODEV;
+        return 0;
+}
+
+/**
+ *      isapnp_remove_one       -       unplug an isapnp interface
+ *      @idev: PnP device
+ *
+ *      Remove a previously configured PnP ATA port. Called only on module
+ *      unload events as the core does not currently deal with ISAPnP docking.
+ */
+
+static void isapnp_remove_one(struct pnp_dev *idev)
+{
+        struct device *dev = &idev->dev;
+        struct ata_host *host = dev_get_drvdata(dev);
+
+        ata_host_remove(host);
+        dev_set_drvdata(dev, NULL);
+}
+
+static struct pnp_device_id isapnp_devices[] = {
+        /* Generic ESDI/IDE/ATA compatible hard disk controller */
+        {.id = "PNP0600", .driver_data = 0},
+        {.id = ""}
+};
+
+static struct pnp_driver isapnp_driver = {
+        .name           = DRV_NAME,
+        .id_table       = isapnp_devices,
+        .probe          = isapnp_init_one,
+        .remove         = isapnp_remove_one,
+};
+
+static int __init isapnp_init(void)
+{
+        return pnp_register_driver(&isapnp_driver);
+}
+
+static void __exit isapnp_exit(void)
+{
+        pnp_unregister_driver(&isapnp_driver);
+}
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for ISA PnP ATA");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
+
+module_init(isapnp_init);
+module_exit(isapnp_exit);
diff --git a/drivers/ata/pata_it8172.c b/drivers/ata/pata_it8172.c
new file mode 100644
index 000000000000..53d35bb6fcf9
--- /dev/null
+++ b/drivers/ata/pata_it8172.c
@@ -0,0 +1,288 @@
+/*
+ * pata_it8172.c        - IT8172 PATA for new ATA layer
+ *                        (C) 2005 Red Hat Inc
+ *                        Alan Cox <alan@redhat.com>
+ *
+ * Based heavily on
+ *
+ * BRIEF MODULE DESCRIPTION
+ *      IT8172 IDE controller support
+ *
+ * Copyright 2000 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc.
+ *              stevel@mvista.com or source@mvista.com
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *      TODO
+ *      Check for errata
+ *      See if we really need to force native mode
+ *      PIO timings (also lacking in original)
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_it8172"
+#define DRV_VERSION "0.3.1"
+
+static int it8172_pre_reset(struct ata_port *ap)
+{
+        static const struct pci_bits it8172_enable_bits[] = {
+                { 0x00, 0, 0x00, 0x00 },
+                { 0x40, 1, 0x00, 0x01 }
+        };
+
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+        if (ap->port_no && !pci_test_config_bits(pdev, &it8172_enable_bits[ap->port_no])) {
+                ata_port_disable(ap);
+                printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+                return 0;
+        }
+        ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+}
+
+static void it8172_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, it8172_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      it8172_set_pio_timing   -       set initial PIO mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Called by both the pio and dma setup functions to set the controller
+ *      timings for PIO transfers. We must load both the mode number and
+ *      timing values into the controller.
+ */
+
+static void it8172_set_pio_timing(struct ata_port *ap, struct ata_device *adev, int pio)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u16 reg40;
+
+        pci_read_config_word(pdev, 0x40, &reg40);
+
+        /*
+         * FIX! The DIOR/DIOW pulse width and recovery times in port 0x44
+         * are being left at the default values of 8 PCI clocks (242 nsec
+         * for a 33 MHz clock). These can be safely shortened at higher
+         * PIO modes. The DIOR/DIOW pulse width and recovery times only
+         * apply to PIO modes, not to the DMA modes.
+         */
+
+        /*
+         * Enable port 0x44. The IT8172G spec is confused; it calls
+         * this register the "Slave IDE Timing Register", but in fact,
+         * it controls timing for both master and slave drives.
+         */
+
+        reg40 |= 0x4000;
+        if (adev->devno) {
+                reg40 &= 0xC006;
+                if (pio > 1)
+                        /* Enable prefetch and IORDY sample-point */
+                        reg40 |= 0x0060;
+        } else {
+                reg40 &= 0xC060;
+                if (pio > 1)
+                        /* Enable prefetch and IORDY sample-point */
+                        reg40 |= 0x0006;
+        }
+        /* Write back the enables */
+        pci_write_config_word(pdev, 0x40, reg40);
+}
+
+/**
+ *      it8172_set_piomode      -       set initial PIO mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Called to do the PIO mode setup. We use a shared helper for this
+ *      as the DMA setup must also adjust the PIO timing information.
+ */
+
+static void it8172_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        it8172_set_pio_timing(ap, adev, adev->pio_mode - XFER_PIO_0);
+}
+
+/**
+ *      it8172_set_dmamode      -       set initial DMA mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Called to do the DMA mode setup. We must tune an appropriate PIO
+ *      mode to match.
+ */
+
+static void it8172_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        int dn = (2 * ap->port_no) + adev->devno;
+        u8 reg48, reg4a;
+        int pio;
+
+        static const int pio_map[] = { 1, 3, 4};
+        /*
+         * Setting the DMA cycle time to 2 or 3 PCI clocks (60 and 91 nsec
+         * at 33 MHz PCI clock) seems to cause BadCRC errors during DMA
+         * transfers on some drives, even though both numbers meet the minimum
+         * ATAPI-4 spec of 73 and 54 nsec for UDMA 1 and 2 respectively.
+         * So the faster times are just commented out here. The good news is
+         * that the slower cycle time has very little affect on transfer
+         * performance.
+         */
+
+        pci_read_config_byte(pdev, 0x48, &reg48);
+        pci_read_config_byte(pdev, 0x4A, &reg4a);
+
+        reg4a &= ~(3 << (4 * dn));
+
+        if (adev->dma_mode >= XFER_UDMA_0) {
+                reg48 |= 1 << dn;
+#ifdef UDMA_TIMING_SET
+                reg4a |= ((adev->dma_mode - XFER_UDMA_0) << (4 * dn));
+#endif
+                pio = 4;
+        } else  {
+                pio = pio_map[adev->dma_mode - XFER_MW_DMA_0];
+                reg48 &= ~ (1 << dn);
+        }
+        pci_write_config_byte(pdev, 0x48, reg48);
+        pci_write_config_byte(pdev, 0x4A, reg4a);
+        it8172_set_pio_timing(ap, adev, pio);
+
+}
+
+static struct scsi_host_template it8172_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations it8172_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = it8172_set_piomode,
+        .set_dmamode    = it8172_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = it8172_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static int it8172_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+        static struct ata_port_info info = {
+                .sht = &it8172_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x06,     /* No MWDMA0 support */
+                .udma_mask = 0x7,
+                .port_ops = &it8172_port_ops
+        };
+        static struct ata_port_info *port_info[2] = { &info, &info };
+
+        if ((!(PCI_FUNC(dev->devfn) & 1) ||
+            (!((dev->class >> 8) == PCI_CLASS_STORAGE_IDE))))
+                return -ENODEV; /* IT8172 is more than an IDE controller */
+
+        return ata_pci_init_one(dev, port_info, 2);
+}
+
+static struct pci_device_id it8172[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_IT8172G), },
+        { 0, },
+};
+
+static struct pci_driver it8172_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = it8172,
+        .probe          = it8172_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init it8172_init(void)
+{
+        return pci_register_driver(&it8172_pci_driver);
+}
+
+
+static void __exit it8172_exit(void)
+{
+        pci_unregister_driver(&it8172_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for ITE IT8172");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, it8172);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(it8172_init);
+module_exit(it8172_exit);
diff --git a/drivers/ata/pata_it821x.c b/drivers/ata/pata_it821x.c
new file mode 100644
index 000000000000..af39097d8081
--- /dev/null
+++ b/drivers/ata/pata_it821x.c
@@ -0,0 +1,847 @@
+/*
+ * ata-it821x.c         - IT821x PATA for new ATA layer
+ *                        (C) 2005 Red Hat Inc
+ *                        Alan Cox <alan@redhat.com>
+ *
+ * based upon
+ *
+ * it821x.c
+ *
+ * linux/drivers/ide/pci/it821x.c               Version 0.09    December 2004
+ *
+ * Copyright (C) 2004           Red Hat <alan@redhat.com>
+ *
+ *  May be copied or modified under the terms of the GNU General Public License
+ *  Based in part on the ITE vendor provided SCSI driver.
+ *
+ *  Documentation available from
+ *      http://www.ite.com.tw/pc/IT8212F_V04.pdf
+ *  Some other documents are NDA.
+ *
+ *  The ITE8212 isn't exactly a standard IDE controller. It has two
+ *  modes. In pass through mode then it is an IDE controller. In its smart
+ *  mode its actually quite a capable hardware raid controller disguised
+ *  as an IDE controller. Smart mode only understands DMA read/write and
+ *  identify, none of the fancier commands apply. The IT8211 is identical
+ *  in other respects but lacks the raid mode.
+ *
+ *  Errata:
+ *  o   Rev 0x10 also requires master/slave hold the same DMA timings and
+ *      cannot do ATAPI MWDMA.
+ *  o   The identify data for raid volumes lacks CHS info (technically ok)
+ *      but also fails to set the LBA28 and other bits. We fix these in
+ *      the IDE probe quirk code.
+ *  o   If you write LBA48 sized I/O's (ie > 256 sector) in smart mode
+ *      raid then the controller firmware dies
+ *  o   Smart mode without RAID doesn't clear all the necessary identify
+ *      bits to reduce the command set to the one used
+ *
+ *  This has a few impacts on the driver
+ *  - In pass through mode we do all the work you would expect
+ *  - In smart mode the clocking set up is done by the controller generally
+ *    but we must watch the other limits and filter.
+ *  - There are a few extra vendor commands that actually talk to the
+ *    controller but only work PIO with no IRQ.
+ *
+ *  Vendor areas of the identify block in smart mode are used for the
+ *  timing and policy set up. Each HDD in raid mode also has a serial
+ *  block on the disk. The hardware extra commands are get/set chip status,
+ *  rebuild, get rebuild status.
+ *
+ *  In Linux the driver supports pass through mode as if the device was
+ *  just another IDE controller. If the smart mode is running then
+ *  volumes are managed by the controller firmware and each IDE "disk"
+ *  is a raid volume. Even more cute - the controller can do automated
+ *  hotplug and rebuild.
+ *
+ *  The pass through controller itself is a little demented. It has a
+ *  flaw that it has a single set of PIO/MWDMA timings per channel so
+ *  non UDMA devices restrict each others performance. It also has a
+ *  single clock source per channel so mixed UDMA100/133 performance
+ *  isn't perfect and we have to pick a clock. Thankfully none of this
+ *  matters in smart mode. ATAPI DMA is not currently supported.
+ *
+ *  It seems the smart mode is a win for RAID1/RAID10 but otherwise not.
+ *
+ *  TODO
+ *      -       ATAPI and other speed filtering
+ *      -       Command filter in smart mode
+ *      -       RAID configuration ioctls
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+
+#define DRV_NAME "pata_it821x"
+#define DRV_VERSION "0.3.2"
+
+struct it821x_dev
+{
+        unsigned int smart:1,           /* Are we in smart raid mode */
+                timing10:1;             /* Rev 0x10 */
+        u8      clock_mode;             /* 0, ATA_50 or ATA_66 */
+        u8      want[2][2];             /* Mode/Pri log for master slave */
+        /* We need these for switching the clock when DMA goes on/off
+           The high byte is the 66Mhz timing */
+        u16     pio[2];                 /* Cached PIO values */
+        u16     mwdma[2];               /* Cached MWDMA values */
+        u16     udma[2];                /* Cached UDMA values (per drive) */
+        u16     last_device;            /* Master or slave loaded ? */
+};
+
+#define ATA_66          0
+#define ATA_50          1
+#define ATA_ANY         2
+
+#define UDMA_OFF        0
+#define MWDMA_OFF       0
+
+/*
+ *      We allow users to force the card into non raid mode without
+ *      flashing the alternative BIOS. This is also neccessary right now
+ *      for embedded platforms that cannot run a PC BIOS but are using this
+ *      device.
+ */
+
+static int it8212_noraid;
+
+/**
+ *      it821x_pre_reset        -       probe
+ *      @ap: ATA port
+ *
+ *      Set the cable type
+ */
+
+static int it821x_pre_reset(struct ata_port *ap)
+{
+        ap->cbl = ATA_CBL_PATA80;
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      it821x_error_handler    -       probe/reset
+ *      @ap: ATA port
+ *
+ *      Set the cable type and trigger a probe
+ */
+
+static void it821x_error_handler(struct ata_port *ap)
+{
+        return ata_bmdma_drive_eh(ap, it821x_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      it821x_program  -       program the PIO/MWDMA registers
+ *      @ap: ATA port
+ *      @adev: Device to program
+ *      @timing: Timing value (66Mhz in top 8bits, 50 in the low 8)
+ *
+ *      Program the PIO/MWDMA timing for this channel according to the
+ *      current clock. These share the same register so are managed by
+ *      the DMA start/stop sequence as with the old driver.
+ */
+
+static void it821x_program(struct ata_port *ap, struct ata_device *adev, u16 timing)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        struct it821x_dev *itdev = ap->private_data;
+        int channel = ap->port_no;
+        u8 conf;
+
+        /* Program PIO/MWDMA timing bits */
+        if (itdev->clock_mode == ATA_66)
+                conf = timing >> 8;
+        else
+                conf = timing & 0xFF;
+        pci_write_config_byte(pdev, 0x54 + 4 * channel, conf);
+}
+
+
+/**
+ *      it821x_program_udma     -       program the UDMA registers
+ *      @ap: ATA port
+ *      @adev: ATA device to update
+ *      @timing: Timing bits. Top 8 are for 66Mhz bottom for 50Mhz
+ *
+ *      Program the UDMA timing for this drive according to the
+ *      current clock. Handles the dual clocks and also knows about
+ *      the errata on the 0x10 revision. The UDMA errata is partly handled
+ *      here and partly in start_dma.
+ */
+
+static void it821x_program_udma(struct ata_port *ap, struct ata_device *adev, u16 timing)
+{
+        struct it821x_dev *itdev = ap->private_data;
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        int channel = ap->port_no;
+        int unit = adev->devno;
+        u8 conf;
+
+        /* Program UDMA timing bits */
+        if (itdev->clock_mode == ATA_66)
+                conf = timing >> 8;
+        else
+                conf = timing & 0xFF;
+        if (itdev->timing10 == 0)
+                pci_write_config_byte(pdev, 0x56 + 4 * channel + unit, conf);
+        else {
+                /* Early revision must be programmed for both together */
+                pci_write_config_byte(pdev, 0x56 + 4 * channel, conf);
+                pci_write_config_byte(pdev, 0x56 + 4 * channel + 1, conf);
+        }
+}
+
+/**
+ *      it821x_clock_strategy
+ *      @ap: ATA interface
+ *      @adev: ATA device being updated
+ *
+ *      Select between the 50 and 66Mhz base clocks to get the best
+ *      results for this interface.
+ */
+
+static void it821x_clock_strategy(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        struct it821x_dev *itdev = ap->private_data;
+        u8 unit = adev->devno;
+        struct ata_device *pair = ata_dev_pair(adev);
+
+        int clock, altclock;
+        u8 v;
+        int sel = 0;
+
+        /* Look for the most wanted clocking */
+        if (itdev->want[0][0] > itdev->want[1][0]) {
+                clock = itdev->want[0][1];
+                altclock = itdev->want[1][1];
+        } else {
+                clock = itdev->want[1][1];
+                altclock = itdev->want[0][1];
+        }
+
+        /* Master doesn't care does the slave ? */
+        if (clock == ATA_ANY)
+                clock = altclock;
+
+        /* Nobody cares - keep the same clock */
+        if (clock == ATA_ANY)
+                return;
+        /* No change */
+        if (clock == itdev->clock_mode)
+                return;
+
+        /* Load this into the controller */
+        if (clock == ATA_66)
+                itdev->clock_mode = ATA_66;
+        else {
+                itdev->clock_mode = ATA_50;
+                sel = 1;
+        }
+        pci_read_config_byte(pdev, 0x50, &v);
+        v &= ~(1 << (1 + ap->port_no));
+        v |= sel << (1 + ap->port_no);
+        pci_write_config_byte(pdev, 0x50, v);
+
+        /*
+         *      Reprogram the UDMA/PIO of the pair drive for the switch
+         *      MWDMA will be dealt with by the dma switcher
+         */
+        if (pair && itdev->udma[1-unit] != UDMA_OFF) {
+                it821x_program_udma(ap, pair, itdev->udma[1-unit]);
+                it821x_program(ap, pair, itdev->pio[1-unit]);
+        }
+        /*
+         *      Reprogram the UDMA/PIO of our drive for the switch.
+         *      MWDMA will be dealt with by the dma switcher
+         */
+        if (itdev->udma[unit] != UDMA_OFF) {
+                it821x_program_udma(ap, adev, itdev->udma[unit]);
+                it821x_program(ap, adev, itdev->pio[unit]);
+        }
+}
+
+/**
+ *      it821x_passthru_set_piomode     -       set PIO mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Configure for PIO mode. This is complicated as the register is
+ *      shared by PIO and MWDMA and for both channels.
+ */
+
+static void it821x_passthru_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        /* Spec says 89 ref driver uses 88 */
+        static const u16 pio[]  = { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 };
+        static const u8 pio_want[]    = { ATA_66, ATA_66, ATA_66, ATA_66, ATA_ANY };
+
+        struct it821x_dev *itdev = ap->private_data;
+        int unit = adev->devno;
+        int mode_wanted = adev->pio_mode - XFER_PIO_0;
+
+        /* We prefer 66Mhz clock for PIO 0-3, don't care for PIO4 */
+        itdev->want[unit][1] = pio_want[mode_wanted];
+        itdev->want[unit][0] = 1;       /* PIO is lowest priority */
+        itdev->pio[unit] = pio[mode_wanted];
+        it821x_clock_strategy(ap, adev);
+        it821x_program(ap, adev, itdev->pio[unit]);
+}
+
+/**
+ *      it821x_passthru_set_dmamode     -       set initial DMA mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Set up the DMA modes. The actions taken depend heavily on the mode
+ *      to use. If UDMA is used as is hopefully the usual case then the
+ *      timing register is private and we need only consider the clock. If
+ *      we are using MWDMA then we have to manage the setting ourself as
+ *      we switch devices and mode.
+ */
+
+static void it821x_passthru_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        static const u16 dma[]  =       { 0x8866, 0x3222, 0x3121 };
+        static const u8 mwdma_want[] =  { ATA_ANY, ATA_66, ATA_ANY };
+        static const u16 udma[] =       { 0x4433, 0x4231, 0x3121, 0x2121, 0x1111, 0x2211, 0x1111 };
+        static const u8 udma_want[] =   { ATA_ANY, ATA_50, ATA_ANY, ATA_66, ATA_66, ATA_50, ATA_66 };
+
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        struct it821x_dev *itdev = ap->private_data;
+        int channel = ap->port_no;
+        int unit = adev->devno;
+        u8 conf;
+
+        if (adev->dma_mode >= XFER_UDMA_0) {
+                int mode_wanted = adev->dma_mode - XFER_UDMA_0;
+
+                itdev->want[unit][1] = udma_want[mode_wanted];
+                itdev->want[unit][0] = 3;       /* UDMA is high priority */
+                itdev->mwdma[unit] = MWDMA_OFF;
+                itdev->udma[unit] = udma[mode_wanted];
+                if (mode_wanted >= 5)
+                        itdev->udma[unit] |= 0x8080;    /* UDMA 5/6 select on */
+
+                /* UDMA on. Again revision 0x10 must do the pair */
+                pci_read_config_byte(pdev, 0x50, &conf);
+                if (itdev->timing10)
+                        conf &= channel ? 0x9F: 0xE7;
+                else
+                        conf &= ~ (1 << (3 + 2 * channel + unit));
+                pci_write_config_byte(pdev, 0x50, conf);
+                it821x_clock_strategy(ap, adev);
+                it821x_program_udma(ap, adev, itdev->udma[unit]);
+        } else {
+                int mode_wanted = adev->dma_mode - XFER_MW_DMA_0;
+
+                itdev->want[unit][1] = mwdma_want[mode_wanted];
+                itdev->want[unit][0] = 2;       /* MWDMA is low priority */
+                itdev->mwdma[unit] = dma[mode_wanted];
+                itdev->udma[unit] = UDMA_OFF;
+
+                /* UDMA bits off - Revision 0x10 do them in pairs */
+                pci_read_config_byte(pdev, 0x50, &conf);
+                if (itdev->timing10)
+                        conf |= channel ? 0x60: 0x18;
+                else
+                        conf |= 1 << (3 + 2 * channel + unit);
+                pci_write_config_byte(pdev, 0x50, conf);
+                it821x_clock_strategy(ap, adev);
+        }
+}
+
+/**
+ *      it821x_passthru_dma_start       -       DMA start callback
+ *      @qc: Command in progress
+ *
+ *      Usually drivers set the DMA timing at the point the set_dmamode call
+ *      is made. IT821x however requires we load new timings on the
+ *      transitions in some cases.
+ */
+
+static void it821x_passthru_bmdma_start(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct ata_device *adev = qc->dev;
+        struct it821x_dev *itdev = ap->private_data;
+        int unit = adev->devno;
+
+        if (itdev->mwdma[unit] != MWDMA_OFF)
+                it821x_program(ap, adev, itdev->mwdma[unit]);
+        else if (itdev->udma[unit] != UDMA_OFF && itdev->timing10)
+                it821x_program_udma(ap, adev, itdev->udma[unit]);
+        ata_bmdma_start(qc);
+}
+
+/**
+ *      it821x_passthru_dma_stop        -       DMA stop callback
+ *      @qc: ATA command
+ *
+ *      We loaded new timings in dma_start, as a result we need to restore
+ *      the PIO timings in dma_stop so that the next command issue gets the
+ *      right clock values.
+ */
+
+static void it821x_passthru_bmdma_stop(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct ata_device *adev = qc->dev;
+        struct it821x_dev *itdev = ap->private_data;
+        int unit = adev->devno;
+
+        ata_bmdma_stop(qc);
+        if (itdev->mwdma[unit] != MWDMA_OFF)
+                it821x_program(ap, adev, itdev->pio[unit]);
+}
+
+
+/**
+ *      it821x_passthru_dev_select      -       Select master/slave
+ *      @ap: ATA port
+ *      @device: Device number (not pointer)
+ *
+ *      Device selection hook. If neccessary perform clock switching
+ */
+
+static void it821x_passthru_dev_select(struct ata_port *ap,
+                                       unsigned int device)
+{
+        struct it821x_dev *itdev = ap->private_data;
+        if (itdev && device != itdev->last_device) {
+                struct ata_device *adev = &ap->device[device];
+                it821x_program(ap, adev, itdev->pio[adev->devno]);
+                itdev->last_device = device;
+        }
+        ata_std_dev_select(ap, device);
+}
+
+/**
+ *      it821x_smart_qc_issue_prot      -       wrap qc issue prot
+ *      @qc: command
+ *
+ *      Wrap the command issue sequence for the IT821x. We need to
+ *      perform out own device selection timing loads before the
+ *      usual happenings kick off
+ */
+
+static unsigned int it821x_smart_qc_issue_prot(struct ata_queued_cmd *qc)
+{
+        switch(qc->tf.command)
+        {
+                /* Commands the firmware supports */
+                case ATA_CMD_READ:
+                case ATA_CMD_READ_EXT:
+                case ATA_CMD_WRITE:
+                case ATA_CMD_WRITE_EXT:
+                case ATA_CMD_PIO_READ:
+                case ATA_CMD_PIO_READ_EXT:
+                case ATA_CMD_PIO_WRITE:
+                case ATA_CMD_PIO_WRITE_EXT:
+                case ATA_CMD_READ_MULTI:
+                case ATA_CMD_READ_MULTI_EXT:
+                case ATA_CMD_WRITE_MULTI:
+                case ATA_CMD_WRITE_MULTI_EXT:
+                case ATA_CMD_ID_ATA:
+                /* Arguably should just no-op this one */
+                case ATA_CMD_SET_FEATURES:
+                        return ata_qc_issue_prot(qc);
+        }
+        printk(KERN_DEBUG "it821x: can't process command 0x%02X\n", qc->tf.command);
+        return AC_ERR_INVALID;
+}
+
+/**
+ *      it821x_passthru_qc_issue_prot   -       wrap qc issue prot
+ *      @qc: command
+ *
+ *      Wrap the command issue sequence for the IT821x. We need to
+ *      perform out own device selection timing loads before the
+ *      usual happenings kick off
+ */
+
+static unsigned int it821x_passthru_qc_issue_prot(struct ata_queued_cmd *qc)
+{
+        it821x_passthru_dev_select(qc->ap, qc->dev->devno);
+        return ata_qc_issue_prot(qc);
+}
+
+/**
+ *      it821x_smart_set_mode   -       mode setting
+ *      @ap: interface to set up
+ *
+ *      Use a non standard set_mode function. We don't want to be tuned.
+ *      The BIOS configured everything. Our job is not to fiddle. We
+ *      read the dma enabled bits from the PCI configuration of the device
+ *      and respect them.
+ */
+
+static void it821x_smart_set_mode(struct ata_port *ap)
+{
+        int dma_enabled = 0;
+        int i;
+
+        /* Bits 5 and 6 indicate if DMA is active on master/slave */
+        /* It is possible that BMDMA isn't allocated */
+        if (ap->ioaddr.bmdma_addr)
+                dma_enabled = inb(ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
+
+        for (i = 0; i < ATA_MAX_DEVICES; i++) {
+                struct ata_device *dev = &ap->device[i];
+                if (ata_dev_enabled(dev)) {
+                        /* We don't really care */
+                        dev->pio_mode = XFER_PIO_0;
+                        dev->dma_mode = XFER_MW_DMA_0;
+                        /* We do need the right mode information for DMA or PIO
+                           and this comes from the current configuration flags */
+                        if (dma_enabled & (1 << (5 + i))) {
+                                dev->xfer_mode = XFER_MW_DMA_0;
+                                dev->xfer_shift = ATA_SHIFT_MWDMA;
+                                dev->flags &= ~ATA_DFLAG_PIO;
+                        } else {
+                                dev->xfer_mode = XFER_PIO_0;
+                                dev->xfer_shift = ATA_SHIFT_PIO;
+                                dev->flags |= ATA_DFLAG_PIO;
+                        }
+                }
+        }
+}
+
+/**
+ *      it821x_dev_config       -       Called each device identify
+ *      @ap: ATA port
+ *      @adev: Device that has just been identified
+ *
+ *      Perform the initial setup needed for each device that is chip
+ *      special. In our case we need to lock the sector count to avoid
+ *      blowing the brains out of the firmware with large LBA48 requests
+ *
+ *      FIXME: When FUA appears we need to block FUA too. And SMART and
+ *      basically we need to filter commands for this chip.
+ */
+
+static void it821x_dev_config(struct ata_port *ap, struct ata_device *adev)
+{
+        unsigned char model_num[40];
+        char *s;
+        unsigned int len;
+
+        /* This block ought to be a library routine as it is in several
+           drivers now */
+
+        ata_id_string(adev->id, model_num, ATA_ID_PROD_OFS,
+                          sizeof(model_num));
+        s = &model_num[0];
+        len = strnlen(s, sizeof(model_num));
+
+        /* ATAPI specifies that empty space is blank-filled; remove blanks */
+        while ((len > 0) && (s[len - 1] == ' ')) {
+                len--;
+                s[len] = 0;
+        }
+
+        if (adev->max_sectors > 255)
+                adev->max_sectors = 255;
+
+        if (strstr(model_num, "Integrated Technology Express")) {
+                /* RAID mode */
+                printk(KERN_INFO "IT821x %sRAID%d volume",
+                        adev->id[147]?"Bootable ":"",
+                        adev->id[129]);
+                if (adev->id[129] != 1)
+                        printk("(%dK stripe)", adev->id[146]);
+                printk(".\n");
+        }
+}
+
+
+/**
+ *      it821x_check_atapi_dma  -       ATAPI DMA handler
+ *      @qc: Command we are about to issue
+ *
+ *      Decide if this ATAPI command can be issued by DMA on this
+ *      controller. Return 0 if it can be.
+ */
+
+static int it821x_check_atapi_dma(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct it821x_dev *itdev = ap->private_data;
+
+        /* No ATAPI DMA in smart mode */
+        if (itdev->smart)
+                return -EOPNOTSUPP;
+        /* No ATAPI DMA on rev 10 */
+        if (itdev->timing10)
+                return -EOPNOTSUPP;
+        /* Cool */
+        return 0;
+}
+
+
+/**
+ *      it821x_port_start       -       port setup
+ *      @ap: ATA port being set up
+ *
+ *      The it821x needs to maintain private data structures and also to
+ *      use the standard PCI interface which lacks support for this
+ *      functionality. We instead set up the private data on the port
+ *      start hook, and tear it down on port stop
+ */
+
+static int it821x_port_start(struct ata_port *ap)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        struct it821x_dev *itdev;
+        u8 conf;
+
+        int ret = ata_port_start(ap);
+        if (ret < 0)
+                return ret;
+
+        ap->private_data = kmalloc(sizeof(struct it821x_dev), GFP_KERNEL);
+        if (ap->private_data == NULL) {
+                ata_port_stop(ap);
+                return -ENOMEM;
+        }
+
+        itdev = ap->private_data;
+        memset(itdev, 0, sizeof(struct it821x_dev));
+
+        pci_read_config_byte(pdev, 0x50, &conf);
+
+        if (conf & 1) {
+                itdev->smart = 1;
+                /* Long I/O's although allowed in LBA48 space cause the
+                   onboard firmware to enter the twighlight zone */
+                /* No ATAPI DMA in this mode either */
+        }
+        /* Pull the current clocks from 0x50 */
+        if (conf & (1 << (1 + ap->port_no)))
+                itdev->clock_mode = ATA_50;
+        else
+                itdev->clock_mode = ATA_66;
+
+        itdev->want[0][1] = ATA_ANY;
+        itdev->want[1][1] = ATA_ANY;
+        itdev->last_device = -1;
+
+        pci_read_config_byte(pdev, PCI_REVISION_ID, &conf);
+        if (conf == 0x10) {
+                itdev->timing10 = 1;
+                /* Need to disable ATAPI DMA for this case */
+                if (!itdev->smart)
+                        printk(KERN_WARNING DRV_NAME": Revision 0x10, workarounds activated.\n");
+        }
+
+        return 0;
+}
+
+/**
+ *      it821x_port_stop        -       port shutdown
+ *      @ap: ATA port being removed
+ *
+ *      Release the private objects we added in it821x_port_start
+ */
+
+static void it821x_port_stop(struct ata_port *ap) {
+        kfree(ap->private_data);
+        ap->private_data = NULL;        /* We want an OOPS if we reuse this
+                                           too late! */
+        ata_port_stop(ap);
+}
+
+static struct scsi_host_template it821x_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        /* 255 sectors to begin with. This is locked in smart mode but not
+           in pass through */
+        .max_sectors            = 255,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations it821x_smart_port_ops = {
+        .set_mode       = it821x_smart_set_mode,
+        .port_disable   = ata_port_disable,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .mode_filter    = ata_pci_default_filter,
+
+        .check_status   = ata_check_status,
+        .check_atapi_dma= it821x_check_atapi_dma,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+        .dev_config     = it821x_dev_config,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = it821x_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = it821x_smart_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = it821x_port_start,
+        .port_stop      = it821x_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static struct ata_port_operations it821x_passthru_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = it821x_passthru_set_piomode,
+        .set_dmamode    = it821x_passthru_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .check_atapi_dma= it821x_check_atapi_dma,
+        .dev_select     = it821x_passthru_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = it821x_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = it821x_passthru_bmdma_start,
+        .bmdma_stop     = it821x_passthru_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = it821x_passthru_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_clear      = ata_bmdma_irq_clear,
+        .irq_handler    = ata_interrupt,
+
+        .port_start     = it821x_port_start,
+        .port_stop      = it821x_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static void __devinit it821x_disable_raid(struct pci_dev *pdev)
+{
+        /* Reset local CPU, and set BIOS not ready */
+        pci_write_config_byte(pdev, 0x5E, 0x01);
+
+        /* Set to bypass mode, and reset PCI bus */
+        pci_write_config_byte(pdev, 0x50, 0x00);
+        pci_write_config_word(pdev, PCI_COMMAND,
+                              PCI_COMMAND_PARITY | PCI_COMMAND_IO |
+                              PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+        pci_write_config_word(pdev, 0x40, 0xA0F3);
+
+        pci_write_config_dword(pdev,0x4C, 0x02040204);
+        pci_write_config_byte(pdev, 0x42, 0x36);
+        pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x20);
+}
+
+
+static int it821x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+        u8 conf;
+
+        static struct ata_port_info info_smart = {
+                .sht = &it821x_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .port_ops = &it821x_smart_port_ops
+        };
+        static struct ata_port_info info_passthru = {
+                .sht = &it821x_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x7f,
+                .port_ops = &it821x_passthru_port_ops
+        };
+        static struct ata_port_info *port_info[2];
+
+        static char *mode[2] = { "pass through", "smart" };
+
+        /* Force the card into bypass mode if so requested */
+        if (it8212_noraid) {
+                printk(KERN_INFO DRV_NAME ": forcing bypass mode.\n");
+                it821x_disable_raid(pdev);
+        }
+        pci_read_config_byte(pdev, 0x50, &conf);
+        conf &= 1;
+
+        printk(KERN_INFO DRV_NAME ": controller in %s mode.\n", mode[conf]);
+        if (conf == 0)
+                port_info[0] = port_info[1] = &info_passthru;
+        else
+                port_info[0] = port_info[1] = &info_smart;
+
+        return ata_pci_init_one(pdev, port_info, 2);
+}
+
+static struct pci_device_id it821x[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8211), },
+        { PCI_DEVICE(PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8212), },
+        { 0, },
+};
+
+static struct pci_driver it821x_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = it821x,
+        .probe          = it821x_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init it821x_init(void)
+{
+        return pci_register_driver(&it821x_pci_driver);
+}
+
+
+static void __exit it821x_exit(void)
+{
+        pci_unregister_driver(&it821x_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for the IT8211/IT8212 IDE RAID controller");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, it821x);
+MODULE_VERSION(DRV_VERSION);
+
+
+module_param_named(noraid, it8212_noraid, int, S_IRUGO);
+MODULE_PARM_DESC(it8212_noraid, "Force card into bypass mode");
+
+module_init(it821x_init);
+module_exit(it821x_exit);
diff --git a/drivers/ata/pata_jmicron.c b/drivers/ata/pata_jmicron.c
new file mode 100644
index 000000000000..6832a643a9eb
--- /dev/null
+++ b/drivers/ata/pata_jmicron.c
@@ -0,0 +1,266 @@
+/*
+ *    pata_jmicron.c - JMicron ATA driver for non AHCI mode. This drives the
+ *                      PATA port of the controller. The SATA ports are
+ *                      driven by AHCI in the usual configuration although
+ *                      this driver can handle other setups if we need it.
+ *
+ *      (c) 2006 Red Hat  <alan@redhat.com>
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/ata.h>
+
+#define DRV_NAME        "pata_jmicron"
+#define DRV_VERSION     "0.1.2"
+
+typedef enum {
+        PORT_PATA0 = 0,
+        PORT_PATA1 = 1,
+        PORT_SATA = 2,
+} port_type;
+
+/**
+ *      jmicron_pre_reset       -       check for 40/80 pin
+ *      @ap: Port
+ *
+ *      Perform the PATA port setup we need.
+
+ *      On the Jmicron 361/363 there is a single PATA port that can be mapped
+ *      either as primary or secondary (or neither). We don't do any policy
+ *      and setup here. We assume that has been done by init_one and the
+ *      BIOS.
+ */
+
+static int jmicron_pre_reset(struct ata_port *ap)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u32 control;
+        u32 control5;
+        int port_mask = 1<< (4 * ap->port_no);
+        int port = ap->port_no;
+        port_type port_map[2];
+
+        /* Check if our port is enabled */
+        pci_read_config_dword(pdev, 0x40, &control);
+        if ((control & port_mask) == 0)
+                return 0;
+
+        /* There are two basic mappings. One has the two SATA ports merged
+           as master/slave and the secondary as PATA, the other has only the
+           SATA port mapped */
+        if (control & (1 << 23)) {
+                port_map[0] = PORT_SATA;
+                port_map[1] = PORT_PATA0;
+        } else {
+                port_map[0] = PORT_SATA;
+                port_map[1] = PORT_SATA;
+        }
+
+        /* The 365/366 may have this bit set to map the second PATA port
+           as the internal primary channel */
+        pci_read_config_dword(pdev, 0x80, &control5);
+        if (control5 & (1<<24))
+                port_map[0] = PORT_PATA1;
+
+        /* The two ports may then be logically swapped by the firmware */
+        if (control & (1 << 22))
+                port = port ^ 1;
+
+        /*
+         *      Now we know which physical port we are talking about we can
+         *      actually do our cable checking etc. Thankfully we don't need
+         *      to do the plumbing for other cases.
+         */
+        switch (port_map[port])
+        {
+        case PORT_PATA0:
+                if (control & (1 << 5))
+                        return 0;
+                if (control & (1 << 3)) /* 40/80 pin primary */
+                        ap->cbl = ATA_CBL_PATA40;
+                else
+                        ap->cbl = ATA_CBL_PATA80;
+                break;
+        case PORT_PATA1:
+                /* Bit 21 is set if the port is enabled */
+                if ((control5 & (1 << 21)) == 0)
+                        return 0;
+                if (control5 & (1 << 19))       /* 40/80 pin secondary */
+                        ap->cbl = ATA_CBL_PATA40;
+                else
+                        ap->cbl = ATA_CBL_PATA80;
+                break;
+        case PORT_SATA:
+                ap->cbl = ATA_CBL_SATA;
+                break;
+        }
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      jmicron_error_handler - Setup and error handler
+ *      @ap: Port to handle
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void jmicron_error_handler(struct ata_port *ap)
+{
+        return ata_bmdma_drive_eh(ap, jmicron_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/* No PIO or DMA methods needed for this device */
+
+static struct scsi_host_template jmicron_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        /* Special handling needed if you have sector or LBA48 limits */
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        /* Use standard CHS mapping rules */
+        .bios_param             = ata_std_bios_param,
+};
+
+static const struct ata_port_operations jmicron_ops = {
+        .port_disable           = ata_port_disable,
+
+        /* Task file is PCI ATA format, use helpers */
+        .tf_load                = ata_tf_load,
+        .tf_read                = ata_tf_read,
+        .check_status           = ata_check_status,
+        .exec_command           = ata_exec_command,
+        .dev_select             = ata_std_dev_select,
+
+        .freeze                 = ata_bmdma_freeze,
+        .thaw                   = ata_bmdma_thaw,
+        .error_handler          = jmicron_error_handler,
+        .post_internal_cmd      = ata_bmdma_post_internal_cmd,
+
+        /* BMDMA handling is PCI ATA format, use helpers */
+        .bmdma_setup            = ata_bmdma_setup,
+        .bmdma_start            = ata_bmdma_start,
+        .bmdma_stop             = ata_bmdma_stop,
+        .bmdma_status           = ata_bmdma_status,
+        .qc_prep                = ata_qc_prep,
+        .qc_issue               = ata_qc_issue_prot,
+        .data_xfer              = ata_pio_data_xfer,
+
+        /* Timeout handling. Special recovery hooks here */
+        .eng_timeout            = ata_eng_timeout,
+        .irq_handler            = ata_interrupt,
+        .irq_clear              = ata_bmdma_irq_clear,
+
+        /* Generic PATA PCI ATA helpers */
+        .port_start             = ata_port_start,
+        .port_stop              = ata_port_stop,
+        .host_stop              = ata_host_stop,
+};
+
+
+/**
+ *      jmicron_init_one - Register Jmicron ATA PCI device with kernel services
+ *      @pdev: PCI device to register
+ *      @ent: Entry in jmicron_pci_tbl matching with @pdev
+ *
+ *      Called from kernel PCI layer.
+ *
+ *      LOCKING:
+ *      Inherited from PCI layer (may sleep).
+ *
+ *      RETURNS:
+ *      Zero on success, or -ERRNO value.
+ */
+
+static int jmicron_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
+{
+        static struct ata_port_info info = {
+                .sht            = &jmicron_sht,
+                .flags  = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+
+                .pio_mask       = 0x1f,
+                .mwdma_mask     = 0x07,
+                .udma_mask      = 0x3f,
+
+                .port_ops       = &jmicron_ops,
+        };
+        struct ata_port_info *port_info[2] = { &info, &info };
+
+        u32 reg;
+
+        if (id->driver_data != 368) {
+                /* Put the controller into AHCI mode in case the AHCI driver
+                   has not yet been loaded. This can be done with either
+                   function present */
+
+                /* FIXME: We may want a way to override this in future */
+                pci_write_config_byte(pdev, 0x41, 0xa1);
+        }
+
+        /* PATA controller is fn 1, AHCI is fn 0 */
+        if (PCI_FUNC(pdev->devfn) != 1)
+                return -ENODEV;
+
+        if ( id->driver_data == 365 || id->driver_data == 366) {
+                /* The 365/66 have two PATA channels, redirect the second */
+                pci_read_config_dword(pdev, 0x80, &reg);
+                reg |= (1 << 24);       /* IDE1 to PATA IDE secondary */
+                pci_write_config_dword(pdev, 0x80, reg);
+        }
+
+        return ata_pci_init_one(pdev, port_info, 2);
+}
+
+static const struct pci_device_id jmicron_pci_tbl[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361), 361},
+        { PCI_DEVICE(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363), 363},
+        { PCI_DEVICE(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365), 365},
+        { PCI_DEVICE(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366), 366},
+        { PCI_DEVICE(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368), 368},
+        { }     /* terminate list */
+};
+
+static struct pci_driver jmicron_pci_driver = {
+        .name                   = DRV_NAME,
+        .id_table               = jmicron_pci_tbl,
+        .probe                  = jmicron_init_one,
+        .remove                 = ata_pci_remove_one,
+};
+
+static int __init jmicron_init(void)
+{
+        return pci_register_driver(&jmicron_pci_driver);
+}
+
+static void __exit jmicron_exit(void)
+{
+        pci_unregister_driver(&jmicron_pci_driver);
+}
+
+module_init(jmicron_init);
+module_exit(jmicron_exit);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("SCSI low-level driver for Jmicron PATA ports");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, jmicron_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+
diff --git a/drivers/ata/pata_legacy.c b/drivers/ata/pata_legacy.c
new file mode 100644
index 000000000000..ad37c220bb2c
--- /dev/null
+++ b/drivers/ata/pata_legacy.c
@@ -0,0 +1,949 @@
+/*
+ *   pata-legacy.c - Legacy port PATA/SATA controller driver.
+ *   Copyright 2005/2006 Red Hat <alan@redhat.com>, all rights reserved.
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2, or (at your option)
+ *  any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; see the file COPYING.  If not, write to
+ *  the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *   An ATA driver for the legacy ATA ports.
+ *
+ *   Data Sources:
+ *      Opti 82C465/82C611 support: Data sheets at opti-inc.com
+ *      HT6560 series:
+ *      Promise 20230/20620:
+ *              http://www.ryston.cz/petr/vlb/pdc20230b.html
+ *              http://www.ryston.cz/petr/vlb/pdc20230c.html
+ *              http://www.ryston.cz/petr/vlb/pdc20630.html
+ *
+ *  Unsupported but docs exist:
+ *      Appian/Adaptec AIC25VL01/Cirrus Logic PD7220
+ *      Winbond W83759A
+ *
+ *  This driver handles legacy (that is "ISA/VLB side") IDE ports found
+ *  on PC class systems. There are three hybrid devices that are exceptions
+ *  The Cyrix 5510/5520 where a pre SFF ATA device is on the bridge and
+ *  the MPIIX where the tuning is PCI side but the IDE is "ISA side".
+ *
+ *  Specific support is included for the ht6560a/ht6560b/opti82c611a/
+ *  opti82c465mv/promise 20230c/20630
+ *
+ *  Use the autospeed and pio_mask options with:
+ *      Appian ADI/2 aka CLPD7220 or AIC25VL01.
+ *  Use the jumpers, autospeed and set pio_mask to the mode on the jumpers with
+ *      Goldstar GM82C711, PIC-1288A-125, UMC 82C871F, Winbond W83759,
+ *      Winbond W83759A, Promise PDC20230-B
+ *
+ *  For now use autospeed and pio_mask as above with the W83759A. This may
+ *  change.
+ *
+ *  TODO
+ *      Merge existing pata_qdi driver
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/ata.h>
+#include <linux/libata.h>
+#include <linux/platform_device.h>
+
+#define DRV_NAME "pata_legacy"
+#define DRV_VERSION "0.5.3"
+
+#define NR_HOST 6
+
+static int legacy_port[NR_HOST] = { 0x1f0, 0x170, 0x1e8, 0x168, 0x1e0, 0x160 };
+static int legacy_irq[NR_HOST] = { 15, 14, 11, 10, 8, 12 };
+
+struct legacy_data {
+        unsigned long timing;
+        u8 clock[2];
+        u8 last;
+        int fast;
+        struct platform_device *platform_dev;
+
+};
+
+static struct legacy_data legacy_data[NR_HOST];
+static struct ata_host *legacy_host[NR_HOST];
+static int nr_legacy_host;
+
+
+static int probe_all;                   /* Set to check all ISA port ranges */
+static int ht6560a;                     /* HT 6560A on primary 1, secondary 2, both 3 */
+static int ht6560b;                     /* HT 6560A on primary 1, secondary 2, both 3 */
+static int opti82c611a;                 /* Opti82c611A on primary 1, secondary 2, both 3 */
+static int opti82c46x;          /* Opti 82c465MV present (pri/sec autodetect) */
+static int autospeed;                   /* Chip present which snoops speed changes */
+static int pio_mask = 0x1F;             /* PIO range for autospeed devices */
+
+/**
+ *      legacy_set_mode         -       mode setting
+ *      @ap: IDE interface
+ *
+ *      Use a non standard set_mode function. We don't want to be tuned.
+ *
+ *      The BIOS configured everything. Our job is not to fiddle. Just use
+ *      whatever PIO the hardware is using and leave it at that. When we
+ *      get some kind of nice user driven API for control then we can
+ *      expand on this as per hdparm in the base kernel.
+ */
+
+static void legacy_set_mode(struct ata_port *ap)
+{
+        int i;
+
+        for (i = 0; i < ATA_MAX_DEVICES; i++) {
+                struct ata_device *dev = &ap->device[i];
+                if (ata_dev_enabled(dev)) {
+                        dev->pio_mode = XFER_PIO_0;
+                        dev->xfer_mode = XFER_PIO_0;
+                        dev->xfer_shift = ATA_SHIFT_PIO;
+                        dev->flags |= ATA_DFLAG_PIO;
+                }
+        }
+}
+
+static struct scsi_host_template legacy_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+/*
+ *      These ops are used if the user indicates the hardware
+ *      snoops the commands to decide on the mode and handles the
+ *      mode selection "magically" itself. Several legacy controllers
+ *      do this. The mode range can be set if it is not 0x1F by setting
+ *      pio_mask as well.
+ */
+
+static struct ata_port_operations simple_port_ops = {
+        .port_disable   = ata_port_disable,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = ata_bmdma_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer_noirq,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static struct ata_port_operations legacy_port_ops = {
+        .set_mode       = legacy_set_mode,
+
+        .port_disable   = ata_port_disable,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .error_handler  = ata_bmdma_error_handler,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer_noirq,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/*
+ *      Promise 20230C and 20620 support
+ *
+ *      This controller supports PIO0 to PIO2. We set PIO timings conservatively to
+ *      allow for 50MHz Vesa Local Bus. The 20620 DMA support is weird being DMA to
+ *      controller and PIO'd to the host and not supported.
+ */
+
+static void pdc20230_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        int tries = 5;
+        int pio = adev->pio_mode - XFER_PIO_0;
+        u8 rt;
+        unsigned long flags;
+
+        /* Safe as UP only. Force I/Os to occur together */
+
+        local_irq_save(flags);
+
+        /* Unlock the control interface */
+        do
+        {
+                inb(0x1F5);
+                outb(inb(0x1F2) | 0x80, 0x1F2);
+                inb(0x1F2);
+                inb(0x3F6);
+                inb(0x3F6);
+                inb(0x1F2);
+                inb(0x1F2);
+        }
+        while((inb(0x1F2) & 0x80) && --tries);
+
+        local_irq_restore(flags);
+
+        outb(inb(0x1F4) & 0x07, 0x1F4);
+
+        rt = inb(0x1F3);
+        rt &= 0x07 << (3 * adev->devno);
+        if (pio)
+                rt |= (1 + 3 * pio) << (3 * adev->devno);
+
+        udelay(100);
+        outb(inb(0x1F2) | 0x01, 0x1F2);
+        udelay(100);
+        inb(0x1F5);
+
+}
+
+static void pdc_data_xfer_vlb(struct ata_device *adev, unsigned char *buf, unsigned int buflen, int write_data)
+{
+        struct ata_port *ap = adev->ap;
+        int slop = buflen & 3;
+        unsigned long flags;
+
+        if (ata_id_has_dword_io(adev->id)) {
+                local_irq_save(flags);
+
+                /* Perform the 32bit I/O synchronization sequence */
+                inb(ap->ioaddr.nsect_addr);
+                inb(ap->ioaddr.nsect_addr);
+                inb(ap->ioaddr.nsect_addr);
+
+                /* Now the data */
+
+                if (write_data)
+                        outsl(ap->ioaddr.data_addr, buf, buflen >> 2);
+                else
+                        insl(ap->ioaddr.data_addr, buf, buflen >> 2);
+
+                if (unlikely(slop)) {
+                        u32 pad;
+                        if (write_data) {
+                                memcpy(&pad, buf + buflen - slop, slop);
+                                outl(le32_to_cpu(pad), ap->ioaddr.data_addr);
+                        } else {
+                                pad = cpu_to_le16(inl(ap->ioaddr.data_addr));
+                                memcpy(buf + buflen - slop, &pad, slop);
+                        }
+                }
+                local_irq_restore(flags);
+        }
+        else
+                ata_pio_data_xfer_noirq(adev, buf, buflen, write_data);
+}
+
+static struct ata_port_operations pdc20230_port_ops = {
+        .set_piomode    = pdc20230_set_piomode,
+
+        .port_disable   = ata_port_disable,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .error_handler  = ata_bmdma_error_handler,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = pdc_data_xfer_vlb,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/*
+ *      Holtek 6560A support
+ *
+ *      This controller supports PIO0 to PIO2 (no IORDY even though higher timings
+ *      can be loaded).
+ */
+
+static void ht6560a_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        u8 active, recover;
+        struct ata_timing t;
+
+        /* Get the timing data in cycles. For now play safe at 50Mhz */
+        ata_timing_compute(adev, adev->pio_mode, &t, 20000, 1000);
+
+        active = FIT(t.active, 2, 15);
+        recover = FIT(t.recover, 4, 15);
+
+        inb(0x3E6);
+        inb(0x3E6);
+        inb(0x3E6);
+        inb(0x3E6);
+
+        outb(recover << 4 | active, ap->ioaddr.device_addr);
+        inb(ap->ioaddr.status_addr);
+}
+
+static struct ata_port_operations ht6560a_port_ops = {
+        .set_piomode    = ht6560a_set_piomode,
+
+        .port_disable   = ata_port_disable,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .error_handler  = ata_bmdma_error_handler,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,    /* Check vlb/noirq */
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/*
+ *      Holtek 6560B support
+ *
+ *      This controller supports PIO0 to PIO4. We honour the BIOS/jumper FIFO setting
+ *      unless we see an ATAPI device in which case we force it off.
+ *
+ *      FIXME: need to implement 2nd channel support.
+ */
+
+static void ht6560b_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        u8 active, recover;
+        struct ata_timing t;
+
+        /* Get the timing data in cycles. For now play safe at 50Mhz */
+        ata_timing_compute(adev, adev->pio_mode, &t, 20000, 1000);
+
+        active = FIT(t.active, 2, 15);
+        recover = FIT(t.recover, 2, 16);
+        recover &= 0x15;
+
+        inb(0x3E6);
+        inb(0x3E6);
+        inb(0x3E6);
+        inb(0x3E6);
+
+        outb(recover << 4 | active, ap->ioaddr.device_addr);
+
+        if (adev->class != ATA_DEV_ATA) {
+                u8 rconf = inb(0x3E6);
+                if (rconf & 0x24) {
+                        rconf &= ~ 0x24;
+                        outb(rconf, 0x3E6);
+                }
+        }
+        inb(ap->ioaddr.status_addr);
+}
+
+static struct ata_port_operations ht6560b_port_ops = {
+        .set_piomode    = ht6560b_set_piomode,
+
+        .port_disable   = ata_port_disable,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .error_handler  = ata_bmdma_error_handler,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,    /* FIXME: Check 32bit and noirq */
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/*
+ *      Opti core chipset helpers
+ */
+
+/**
+ *      opti_syscfg     -       read OPTI chipset configuration
+ *      @reg: Configuration register to read
+ *
+ *      Returns the value of an OPTI system board configuration register.
+ */
+
+static u8 opti_syscfg(u8 reg)
+{
+        unsigned long flags;
+        u8 r;
+
+        /* Uniprocessor chipset and must force cycles adjancent */
+        local_irq_save(flags);
+        outb(reg, 0x22);
+        r = inb(0x24);
+        local_irq_restore(flags);
+        return r;
+}
+
+/*
+ *      Opti 82C611A
+ *
+ *      This controller supports PIO0 to PIO3.
+ */
+
+static void opti82c611a_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        u8 active, recover, setup;
+        struct ata_timing t;
+        struct ata_device *pair = ata_dev_pair(adev);
+        int clock;
+        int khz[4] = { 50000, 40000, 33000, 25000 };
+        u8 rc;
+
+        /* Enter configuration mode */
+        inw(ap->ioaddr.error_addr);
+        inw(ap->ioaddr.error_addr);
+        outb(3, ap->ioaddr.nsect_addr);
+
+        /* Read VLB clock strapping */
+        clock = 1000000000 / khz[inb(ap->ioaddr.lbah_addr) & 0x03];
+
+        /* Get the timing data in cycles */
+        ata_timing_compute(adev, adev->pio_mode, &t, clock, 1000);
+
+        /* Setup timing is shared */
+        if (pair) {
+                struct ata_timing tp;
+                ata_timing_compute(pair, pair->pio_mode, &tp, clock, 1000);
+
+                ata_timing_merge(&t, &tp, &t, ATA_TIMING_SETUP);
+        }
+
+        active = FIT(t.active, 2, 17) - 2;
+        recover = FIT(t.recover, 1, 16) - 1;
+        setup = FIT(t.setup, 1, 4) - 1;
+
+        /* Select the right timing bank for write timing */
+        rc = inb(ap->ioaddr.lbal_addr);
+        rc &= 0x7F;
+        rc |= (adev->devno << 7);
+        outb(rc, ap->ioaddr.lbal_addr);
+
+        /* Write the timings */
+        outb(active << 4 | recover, ap->ioaddr.error_addr);
+
+        /* Select the right bank for read timings, also
+           load the shared timings for address */
+        rc = inb(ap->ioaddr.device_addr);
+        rc &= 0xC0;
+        rc |= adev->devno;      /* Index select */
+        rc |= (setup << 4) | 0x04;
+        outb(rc, ap->ioaddr.device_addr);
+
+        /* Load the read timings */
+        outb(active << 4 | recover, ap->ioaddr.data_addr);
+
+        /* Ensure the timing register mode is right */
+        rc = inb (ap->ioaddr.lbal_addr);
+        rc &= 0x73;
+        rc |= 0x84;
+        outb(rc, ap->ioaddr.lbal_addr);
+
+        /* Exit command mode */
+        outb(0x83,  ap->ioaddr.nsect_addr);
+}
+
+
+static struct ata_port_operations opti82c611a_port_ops = {
+        .set_piomode    = opti82c611a_set_piomode,
+
+        .port_disable   = ata_port_disable,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .error_handler  = ata_bmdma_error_handler,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/*
+ *      Opti 82C465MV
+ *
+ *      This controller supports PIO0 to PIO3. Unlike the 611A the MVB
+ *      version is dual channel but doesn't have a lot of unique registers.
+ */
+
+static void opti82c46x_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        u8 active, recover, setup;
+        struct ata_timing t;
+        struct ata_device *pair = ata_dev_pair(adev);
+        int clock;
+        int khz[4] = { 50000, 40000, 33000, 25000 };
+        u8 rc;
+        u8 sysclk;
+
+        /* Get the clock */
+        sysclk = opti_syscfg(0xAC) & 0xC0;      /* BIOS set */
+
+        /* Enter configuration mode */
+        inw(ap->ioaddr.error_addr);
+        inw(ap->ioaddr.error_addr);
+        outb(3, ap->ioaddr.nsect_addr);
+
+        /* Read VLB clock strapping */
+        clock = 1000000000 / khz[sysclk];
+
+        /* Get the timing data in cycles */
+        ata_timing_compute(adev, adev->pio_mode, &t, clock, 1000);
+
+        /* Setup timing is shared */
+        if (pair) {
+                struct ata_timing tp;
+                ata_timing_compute(pair, pair->pio_mode, &tp, clock, 1000);
+
+                ata_timing_merge(&t, &tp, &t, ATA_TIMING_SETUP);
+        }
+
+        active = FIT(t.active, 2, 17) - 2;
+        recover = FIT(t.recover, 1, 16) - 1;
+        setup = FIT(t.setup, 1, 4) - 1;
+
+        /* Select the right timing bank for write timing */
+        rc = inb(ap->ioaddr.lbal_addr);
+        rc &= 0x7F;
+        rc |= (adev->devno << 7);
+        outb(rc, ap->ioaddr.lbal_addr);
+
+        /* Write the timings */
+        outb(active << 4 | recover, ap->ioaddr.error_addr);
+
+        /* Select the right bank for read timings, also
+           load the shared timings for address */
+        rc = inb(ap->ioaddr.device_addr);
+        rc &= 0xC0;
+        rc |= adev->devno;      /* Index select */
+        rc |= (setup << 4) | 0x04;
+        outb(rc, ap->ioaddr.device_addr);
+
+        /* Load the read timings */
+        outb(active << 4 | recover, ap->ioaddr.data_addr);
+
+        /* Ensure the timing register mode is right */
+        rc = inb (ap->ioaddr.lbal_addr);
+        rc &= 0x73;
+        rc |= 0x84;
+        outb(rc, ap->ioaddr.lbal_addr);
+
+        /* Exit command mode */
+        outb(0x83,  ap->ioaddr.nsect_addr);
+
+        /* We need to know this for quad device on the MVB */
+        ap->host->private_data = ap;
+}
+
+/**
+ *      opt82c465mv_qc_issue_prot       -       command issue
+ *      @qc: command pending
+ *
+ *      Called when the libata layer is about to issue a command. We wrap
+ *      this interface so that we can load the correct ATA timings. The
+ *      MVB has a single set of timing registers and these are shared
+ *      across channels. As there are two registers we really ought to
+ *      track the last two used values as a sort of register window. For
+ *      now we just reload on a channel switch. On the single channel
+ *      setup this condition never fires so we do nothing extra.
+ *
+ *      FIXME: dual channel needs ->serialize support
+ */
+
+static unsigned int opti82c46x_qc_issue_prot(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct ata_device *adev = qc->dev;
+
+        /* If timings are set and for the wrong channel (2nd test is
+           due to a libata shortcoming and will eventually go I hope) */
+        if (ap->host->private_data != ap->host
+            && ap->host->private_data != NULL)
+                opti82c46x_set_piomode(ap, adev);
+
+        return ata_qc_issue_prot(qc);
+}
+
+static struct ata_port_operations opti82c46x_port_ops = {
+        .set_piomode    = opti82c46x_set_piomode,
+
+        .port_disable   = ata_port_disable,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .error_handler  = ata_bmdma_error_handler,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = opti82c46x_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+
+/**
+ *      legacy_init_one         -       attach a legacy interface
+ *      @port: port number
+ *      @io: I/O port start
+ *      @ctrl: control port
+ *      @irq: interrupt line
+ *
+ *      Register an ISA bus IDE interface. Such interfaces are PIO and we
+ *      assume do not support IRQ sharing.
+ */
+
+static __init int legacy_init_one(int port, unsigned long io, unsigned long ctrl, int irq)
+{
+        struct legacy_data *ld = &legacy_data[nr_legacy_host];
+        struct ata_probe_ent ae;
+        struct platform_device *pdev;
+        int ret = -EBUSY;
+        struct ata_port_operations *ops = &legacy_port_ops;
+        int pio_modes = pio_mask;
+        u32 mask = (1 << port);
+
+        if (request_region(io, 8, "pata_legacy") == NULL)
+                return -EBUSY;
+        if (request_region(ctrl, 1, "pata_legacy") == NULL)
+                goto fail_io;
+
+        pdev = platform_device_register_simple(DRV_NAME, nr_legacy_host, NULL, 0);
+        if (pdev == NULL)
+                goto fail_dev;
+
+        if (ht6560a & mask) {
+                ops = &ht6560a_port_ops;
+                pio_modes = 0x07;
+        }
+        if (ht6560b & mask) {
+                ops = &ht6560b_port_ops;
+                pio_modes = 0x1F;
+        }
+        if (opti82c611a & mask) {
+                ops = &opti82c611a_port_ops;
+                pio_modes = 0x0F;
+        }
+        if (opti82c46x & mask) {
+                ops = &opti82c46x_port_ops;
+                pio_modes = 0x0F;
+        }
+
+        /* Probe for automatically detectable controllers */
+
+        if (io == 0x1F0 && ops == &legacy_port_ops) {
+                unsigned long flags;
+
+                local_irq_save(flags);
+
+                /* Probes */
+                inb(0x1F5);
+                outb(inb(0x1F2) | 0x80, 0x1F2);
+                inb(0x1F2);
+                inb(0x3F6);
+                inb(0x3F6);
+                inb(0x1F2);
+                inb(0x1F2);
+
+                if ((inb(0x1F2) & 0x80) == 0) {
+                        /* PDC20230c or 20630 ? */
+                        printk(KERN_INFO "PDC20230-C/20630 VLB ATA controller detected.\n");
+                                pio_modes = 0x07;
+                        ops = &pdc20230_port_ops;
+                        udelay(100);
+                        inb(0x1F5);
+                } else {
+                        outb(0x55, 0x1F2);
+                        inb(0x1F2);
+                        inb(0x1F2);
+                        if (inb(0x1F2) == 0x00) {
+                                printk(KERN_INFO "PDC20230-B VLB ATA controller detected.\n");
+                        }
+                }
+                local_irq_restore(flags);
+        }
+
+
+        /* Chip does mode setting by command snooping */
+        if (ops == &legacy_port_ops && (autospeed & mask))
+                ops = &simple_port_ops;
+        memset(&ae, 0, sizeof(struct ata_probe_ent));
+        INIT_LIST_HEAD(&ae.node);
+        ae.dev = &pdev->dev;
+        ae.port_ops = ops;
+        ae.sht = &legacy_sht;
+        ae.n_ports = 1;
+        ae.pio_mask = pio_modes;
+        ae.irq = irq;
+        ae.irq_flags = 0;
+        ae.port_flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST;
+        ae.port[0].cmd_addr = io;
+        ae.port[0].altstatus_addr = ctrl;
+        ae.port[0].ctl_addr =   ctrl;
+        ata_std_ports(&ae.port[0]);
+        ae.private_data = ld;
+
+        ret = ata_device_add(&ae);
+        if (ret == 0) {
+                ret = -ENODEV;
+                goto fail;
+        }
+        legacy_host[nr_legacy_host++] = dev_get_drvdata(&pdev->dev);
+        ld->platform_dev = pdev;
+        return 0;
+
+fail:
+        platform_device_unregister(pdev);
+fail_dev:
+        release_region(ctrl, 1);
+fail_io:
+        release_region(io, 8);
+        return ret;
+}
+
+/**
+ *      legacy_check_special_cases      -       ATA special cases
+ *      @p: PCI device to check
+ *      @master: set this if we find an ATA master
+ *      @master: set this if we find an ATA secondary
+ *
+ *      A small number of vendors implemented early PCI ATA interfaces on bridge logic
+ *      without the ATA interface being PCI visible. Where we have a matching PCI driver
+ *      we must skip the relevant device here. If we don't know about it then the legacy
+ *      driver is the right driver anyway.
+ */
+
+static void legacy_check_special_cases(struct pci_dev *p, int *primary, int *secondary)
+{
+        /* Cyrix CS5510 pre SFF MWDMA ATA on the bridge */
+        if (p->vendor == 0x1078 && p->device == 0x0000) {
+                *primary = *secondary = 1;
+                return;
+        }
+        /* Cyrix CS5520 pre SFF MWDMA ATA on the bridge */
+        if (p->vendor == 0x1078 && p->device == 0x0002) {
+                *primary = *secondary = 1;
+                return;
+        }
+        /* Intel MPIIX - PIO ATA on non PCI side of bridge */
+        if (p->vendor == 0x8086 && p->device == 0x1234) {
+                u16 r;
+                pci_read_config_word(p, 0x6C, &r);
+                if (r & 0x8000) {       /* ATA port enabled */
+                        if (r & 0x4000)
+                                *secondary = 1;
+                        else
+                                *primary = 1;
+                }
+                return;
+        }
+}
+
+
+/**
+ *      legacy_init             -       attach legacy interfaces
+ *
+ *      Attach legacy IDE interfaces by scanning the usual IRQ/port suspects.
+ *      Right now we do not scan the ide0 and ide1 address but should do so
+ *      for non PCI systems or systems with no PCI IDE legacy mode devices.
+ *      If you fix that note there are special cases to consider like VLB
+ *      drivers and CS5510/20.
+ */
+
+static __init int legacy_init(void)
+{
+        int i;
+        int ct = 0;
+        int primary = 0;
+        int secondary = 0;
+        int last_port = NR_HOST;
+
+        struct pci_dev *p = NULL;
+
+        for_each_pci_dev(p) {
+                int r;
+                /* Check for any overlap of the system ATA mappings. Native mode controllers
+                   stuck on these addresses or some devices in 'raid' mode won't be found by
+                   the storage class test */
+                for (r = 0; r < 6; r++) {
+                        if (pci_resource_start(p, r) == 0x1f0)
+                                primary = 1;
+                        if (pci_resource_start(p, r) == 0x170)
+                                secondary = 1;
+                }
+                /* Check for special cases */
+                legacy_check_special_cases(p, &primary, &secondary);
+
+                /* If PCI bus is present then don't probe for tertiary legacy ports */
+                if (probe_all == 0)
+                        last_port = 2;
+        }
+
+        /* If an OPTI 82C46X is present find out where the channels are */
+        if (opti82c46x) {
+                static const char *optis[4] = {
+                        "3/463MV", "5MV",
+                        "5MVA", "5MVB"
+                };
+                u8 chans = 1;
+                u8 ctrl = (opti_syscfg(0x30) & 0xC0) >> 6;
+
+                opti82c46x = 3; /* Assume master and slave first */
+                printk(KERN_INFO DRV_NAME ": Opti 82C46%s chipset support.\n", optis[ctrl]);
+                if (ctrl == 3)
+                        chans = (opti_syscfg(0x3F) & 0x20) ? 2 : 1;
+                ctrl = opti_syscfg(0xAC);
+                /* Check enabled and this port is the 465MV port. On the
+                   MVB we may have two channels */
+                if (ctrl & 8) {
+                        if (ctrl & 4)
+                                opti82c46x = 2; /* Slave */
+                        else
+                                opti82c46x = 1; /* Master */
+                        if (chans == 2)
+                                opti82c46x = 3; /* Master and Slave */
+                }       /* Slave only */
+                else if (chans == 1)
+                        opti82c46x = 1;
+        }
+
+        for (i = 0; i < last_port; i++) {
+                /* Skip primary if we have seen a PCI one */
+                if (i == 0 && primary == 1)
+                        continue;
+                /* Skip secondary if we have seen a PCI one */
+                if (i == 1 && secondary == 1)
+                        continue;
+                if (legacy_init_one(i, legacy_port[i],
+                                   legacy_port[i] + 0x0206,
+                                   legacy_irq[i]) == 0)
+                        ct++;
+        }
+        if (ct != 0)
+                return 0;
+        return -ENODEV;
+}
+
+static __exit void legacy_exit(void)
+{
+        int i;
+
+        for (i = 0; i < nr_legacy_host; i++) {
+                struct legacy_data *ld = &legacy_data[i];
+                struct ata_port *ap =legacy_host[i]->ports[0];
+                unsigned long io = ap->ioaddr.cmd_addr;
+                unsigned long ctrl = ap->ioaddr.ctl_addr;
+                ata_host_remove(legacy_host[i]);
+                platform_device_unregister(ld->platform_dev);
+                if (ld->timing)
+                        release_region(ld->timing, 2);
+                release_region(io, 8);
+                release_region(ctrl, 1);
+        }
+}
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for legacy ATA");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
+
+module_param(probe_all, int, 0);
+module_param(autospeed, int, 0);
+module_param(ht6560a, int, 0);
+module_param(ht6560b, int, 0);
+module_param(opti82c611a, int, 0);
+module_param(opti82c46x, int, 0);
+module_param(pio_mask, int, 0);
+
+module_init(legacy_init);
+module_exit(legacy_exit);
+
diff --git a/drivers/ata/pata_mpiix.c b/drivers/ata/pata_mpiix.c
new file mode 100644
index 000000000000..1958c4ed09a8
--- /dev/null
+++ b/drivers/ata/pata_mpiix.c
@@ -0,0 +1,313 @@
+/*
+ * pata_mpiix.c         - Intel MPIIX PATA for new ATA layer
+ *                        (C) 2005-2006 Red Hat Inc
+ *                        Alan Cox <alan@redhat.com>
+ *
+ * The MPIIX is different enough to the PIIX4 and friends that we give it
+ * a separate driver. The old ide/pci code handles this by just not tuning
+ * MPIIX at all.
+ *
+ * The MPIIX also differs in another important way from the majority of PIIX
+ * devices. The chip is a bridge (pardon the pun) between the old world of
+ * ISA IDE and PCI IDE. Although the ATA timings are PCI configured the actual
+ * IDE controller is not decoded in PCI space and the chip does not claim to
+ * be IDE class PCI. This requires slightly non-standard probe logic compared
+ * with PCI IDE and also that we do not disable the device when our driver is
+ * unloaded (as it has many other functions).
+ *
+ * The driver conciously keeps this logic internally to avoid pushing quirky
+ * PATA history into the clean libata layer.
+ *
+ * Thinkpad specific note: If you boot an MPIIX using thinkpad with a PCMCIA
+ * hard disk present this driver will not detect it. This is not a bug. In this
+ * configuration the secondary port of the MPIIX is disabled and the addresses
+ * are decoded by the PCMCIA bridge and therefore are for a generic IDE driver
+ * to operate.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_mpiix"
+#define DRV_VERSION "0.7.1"
+
+enum {
+        IDETIM = 0x6C,          /* IDE control register */
+        IORDY = (1 << 1),
+        PPE = (1 << 2),
+        FTIM = (1 << 0),
+        ENABLED = (1 << 15),
+        SECONDARY = (1 << 14)
+};
+
+static int mpiix_pre_reset(struct ata_port *ap)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        static const struct pci_bits mpiix_enable_bits[] = {
+                { 0x6D, 1, 0x80, 0x80 },
+                { 0x6F, 1, 0x80, 0x80 }
+        };
+
+        if (!pci_test_config_bits(pdev, &mpiix_enable_bits[ap->port_no])) {
+                ata_port_disable(ap);
+                printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+                return 0;
+        }
+        ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      mpiix_error_handler             -       probe reset
+ *      @ap: ATA port
+ *
+ *      Perform the ATA probe and bus reset sequence plus specific handling
+ *      for this hardware. The MPIIX has the enable bits in a different place
+ *      to PIIX4 and friends. As a pure PIO device it has no cable detect
+ */
+
+static void mpiix_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, mpiix_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      mpiix_set_piomode       -       set initial PIO mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Called to do the PIO mode setup. The MPIIX allows us to program the
+ *      IORDY sample point (2-5 clocks), recovery 1-4 clocks and whether
+ *      prefetching or iordy are used.
+ *
+ *      This would get very ugly because we can only program timing for one
+ *      device at a time, the other gets PIO0. Fortunately libata calls
+ *      our qc_issue_prot command before a command is issued so we can
+ *      flip the timings back and forth to reduce the pain.
+ */
+
+static void mpiix_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        int control = 0;
+        int pio = adev->pio_mode - XFER_PIO_0;
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u16 idetim;
+        static const     /* ISP  RTC */
+        u8 timings[][2] = { { 0, 0 },
+                            { 0, 0 },
+                            { 1, 0 },
+                            { 2, 1 },
+                            { 2, 3 }, };
+
+        pci_read_config_word(pdev, IDETIM, &idetim);
+        /* Mask the IORDY/TIME/PPE0 bank for this device */
+        if (adev->class == ATA_DEV_ATA)
+                control |= PPE;         /* PPE enable for disk */
+        if (ata_pio_need_iordy(adev))
+                control |= IORDY;       /* IORDY */
+        if (pio > 0)
+                control |= FTIM;        /* This drive is on the fast timing bank */
+
+        /* Mask out timing and clear both TIME bank selects */
+        idetim &= 0xCCEE;
+        idetim &= ~(0x07  << (2 * adev->devno));
+        idetim |= (control << (2 * adev->devno));
+
+        idetim |= (timings[pio][0] << 12) | (timings[pio][1] << 8);
+        pci_write_config_word(pdev, IDETIM, idetim);
+
+        /* We use ap->private_data as a pointer to the device currently
+           loaded for timing */
+        ap->private_data = adev;
+}
+
+/**
+ *      mpiix_qc_issue_prot     -       command issue
+ *      @qc: command pending
+ *
+ *      Called when the libata layer is about to issue a command. We wrap
+ *      this interface so that we can load the correct ATA timings if
+ *      neccessary. Our logic also clears TIME0/TIME1 for the other device so
+ *      that, even if we get this wrong, cycles to the other device will
+ *      be made PIO0.
+ */
+
+static unsigned int mpiix_qc_issue_prot(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct ata_device *adev = qc->dev;
+
+        /* If modes have been configured and the channel data is not loaded
+           then load it. We have to check if pio_mode is set as the core code
+           does not set adev->pio_mode to XFER_PIO_0 while probing as would be
+           logical */
+
+        if (adev->pio_mode && adev != ap->private_data)
+                mpiix_set_piomode(ap, adev);
+
+        return ata_qc_issue_prot(qc);
+}
+
+static struct scsi_host_template mpiix_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations mpiix_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = mpiix_set_piomode,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = mpiix_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = mpiix_qc_issue_prot,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static int mpiix_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+        /* Single threaded by the PCI probe logic */
+        static struct ata_probe_ent probe[2];
+        static int printed_version;
+        u16 idetim;
+        int enabled;
+
+        if (!printed_version++)
+                dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n");
+
+        /* MPIIX has many functions which can be turned on or off according
+           to other devices present. Make sure IDE is enabled before we try
+           and use it */
+
+        pci_read_config_word(dev, IDETIM, &idetim);
+        if (!(idetim & ENABLED))
+                return -ENODEV;
+
+        /* We do our own plumbing to avoid leaking special cases for whacko
+           ancient hardware into the core code. There are two issues to
+           worry about.  #1 The chip is a bridge so if in legacy mode and
+           without BARs set fools the setup.  #2 If you pci_disable_device
+           the MPIIX your box goes castors up */
+
+        INIT_LIST_HEAD(&probe[0].node);
+        probe[0].dev = pci_dev_to_dev(dev);
+        probe[0].port_ops = &mpiix_port_ops;
+        probe[0].sht = &mpiix_sht;
+        probe[0].pio_mask = 0x1F;
+        probe[0].irq = 14;
+        probe[0].irq_flags = SA_SHIRQ;
+        probe[0].port_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST;
+        probe[0].n_ports = 1;
+        probe[0].port[0].cmd_addr = 0x1F0;
+        probe[0].port[0].ctl_addr = 0x3F6;
+        probe[0].port[0].altstatus_addr = 0x3F6;
+
+        /* The secondary lurks at different addresses but is otherwise
+           the same beastie */
+
+        INIT_LIST_HEAD(&probe[1].node);
+        probe[1] = probe[0];
+        probe[1].irq = 15;
+        probe[1].port[0].cmd_addr = 0x170;
+        probe[1].port[0].ctl_addr = 0x376;
+        probe[1].port[0].altstatus_addr = 0x376;
+
+        /* Let libata fill in the port details */
+        ata_std_ports(&probe[0].port[0]);
+        ata_std_ports(&probe[1].port[0]);
+
+        /* Now add the port that is active */
+        enabled = (idetim & SECONDARY) ? 1 : 0;
+
+        if (ata_device_add(&probe[enabled]))
+                return 0;
+        return -ENODEV;
+}
+
+/**
+ *      mpiix_remove_one        -       device unload
+ *      @pdev: PCI device being removed
+ *
+ *      Handle an unplug/unload event for a PCI device. Unload the
+ *      PCI driver but do not use the default handler as we *MUST NOT*
+ *      disable the device as it has other functions.
+ */
+
+static void __devexit mpiix_remove_one(struct pci_dev *pdev)
+{
+        struct device *dev = pci_dev_to_dev(pdev);
+        struct ata_host *host = dev_get_drvdata(dev);
+
+        ata_host_remove(host);
+        dev_set_drvdata(dev, NULL);
+}
+
+
+
+static const struct pci_device_id mpiix[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371MX), },
+        { 0, },
+};
+
+static struct pci_driver mpiix_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = mpiix,
+        .probe          = mpiix_init_one,
+        .remove         = mpiix_remove_one
+};
+
+static int __init mpiix_init(void)
+{
+        return pci_register_driver(&mpiix_pci_driver);
+}
+
+
+static void __exit mpiix_exit(void)
+{
+        pci_unregister_driver(&mpiix_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for Intel MPIIX");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, mpiix);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(mpiix_init);
+module_exit(mpiix_exit);
diff --git a/drivers/ata/pata_netcell.c b/drivers/ata/pata_netcell.c
new file mode 100644
index 000000000000..16cb254cb973
--- /dev/null
+++ b/drivers/ata/pata_netcell.c
@@ -0,0 +1,175 @@
+/*
+ *    pata_netcell.c - Netcell PATA driver
+ *
+ *      (c) 2006 Red Hat  <alan@redhat.com>
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/ata.h>
+
+#define DRV_NAME        "pata_netcell"
+#define DRV_VERSION     "0.1.5"
+
+/**
+ *      netcell_probe_init      -       check for 40/80 pin
+ *      @ap: Port
+ *
+ *      Cables are handled by the RAID controller. Report 80 pin.
+ */
+
+static int netcell_pre_reset(struct ata_port *ap)
+{
+        ap->cbl = ATA_CBL_PATA80;
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      netcell_probe_reset - Probe specified port on PATA host controller
+ *      @ap: Port to probe
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void netcell_error_handler(struct ata_port *ap)
+{
+        return ata_bmdma_drive_eh(ap, netcell_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/* No PIO or DMA methods needed for this device */
+
+static struct scsi_host_template netcell_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        /* Special handling needed if you have sector or LBA48 limits */
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        /* Use standard CHS mapping rules */
+        .bios_param             = ata_std_bios_param,
+};
+
+static const struct ata_port_operations netcell_ops = {
+        .port_disable           = ata_port_disable,
+
+        /* Task file is PCI ATA format, use helpers */
+        .tf_load                = ata_tf_load,
+        .tf_read                = ata_tf_read,
+        .check_status           = ata_check_status,
+        .exec_command           = ata_exec_command,
+        .dev_select             = ata_std_dev_select,
+
+        .freeze                 = ata_bmdma_freeze,
+        .thaw                   = ata_bmdma_thaw,
+        .error_handler          = netcell_error_handler,
+        .post_internal_cmd      = ata_bmdma_post_internal_cmd,
+
+        /* BMDMA handling is PCI ATA format, use helpers */
+        .bmdma_setup            = ata_bmdma_setup,
+        .bmdma_start            = ata_bmdma_start,
+        .bmdma_stop             = ata_bmdma_stop,
+        .bmdma_status           = ata_bmdma_status,
+        .qc_prep                = ata_qc_prep,
+        .qc_issue               = ata_qc_issue_prot,
+        .data_xfer              = ata_pio_data_xfer,
+
+        /* Timeout handling. Special recovery hooks here */
+        .eng_timeout            = ata_eng_timeout,
+        .irq_handler            = ata_interrupt,
+        .irq_clear              = ata_bmdma_irq_clear,
+
+        /* Generic PATA PCI ATA helpers */
+        .port_start             = ata_port_start,
+        .port_stop              = ata_port_stop,
+        .host_stop              = ata_host_stop,
+};
+
+
+/**
+ *      netcell_init_one - Register Netcell ATA PCI device with kernel services
+ *      @pdev: PCI device to register
+ *      @ent: Entry in netcell_pci_tbl matching with @pdev
+ *
+ *      Called from kernel PCI layer.
+ *
+ *      LOCKING:
+ *      Inherited from PCI layer (may sleep).
+ *
+ *      RETURNS:
+ *      Zero on success, or -ERRNO value.
+ */
+
+static int netcell_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+        static int printed_version;
+        static struct ata_port_info info = {
+                .sht            = &netcell_sht,
+                .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                /* Actually we don't really care about these as the
+                   firmware deals with it */
+                .pio_mask       = 0x1f, /* pio0-4 */
+                .mwdma_mask     = 0x07, /* mwdma0-2 */
+                .udma_mask      = 0x3f, /* UDMA 133 */
+                .port_ops       = &netcell_ops,
+        };
+        static struct ata_port_info *port_info[2] = { &info, &info };
+
+        if (!printed_version++)
+                dev_printk(KERN_DEBUG, &pdev->dev,
+                           "version " DRV_VERSION "\n");
+
+        /* Any chip specific setup/optimisation/messages here */
+        ata_pci_clear_simplex(pdev);
+
+        /* And let the library code do the work */
+        return ata_pci_init_one(pdev, port_info, 2);
+}
+
+static const struct pci_device_id netcell_pci_tbl[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_NETCELL, PCI_DEVICE_ID_REVOLUTION), },
+        { }     /* terminate list */
+};
+
+static struct pci_driver netcell_pci_driver = {
+        .name                   = DRV_NAME,
+        .id_table               = netcell_pci_tbl,
+        .probe                  = netcell_init_one,
+        .remove                 = ata_pci_remove_one,
+};
+
+static int __init netcell_init(void)
+{
+        return pci_register_driver(&netcell_pci_driver);
+}
+
+static void __exit netcell_exit(void)
+{
+        pci_unregister_driver(&netcell_pci_driver);
+}
+
+module_init(netcell_init);
+module_exit(netcell_exit);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("SCSI low-level driver for Netcell PATA RAID");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, netcell_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+
diff --git a/drivers/ata/pata_ns87410.c b/drivers/ata/pata_ns87410.c
new file mode 100644
index 000000000000..93d6646d2954
--- /dev/null
+++ b/drivers/ata/pata_ns87410.c
@@ -0,0 +1,236 @@
+/*
+ * pata_ns87410.c       - National Semiconductor 87410 PATA for new ATA layer
+ *                        (C) 2006 Red Hat Inc
+ *                        Alan Cox <alan@redhat.com>
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2, or (at your option)
+ *  any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; see the file COPYING.  If not, write to
+ *  the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_ns87410"
+#define DRV_VERSION "0.4.2"
+
+/**
+ *      ns87410_pre_reset               -       probe begin
+ *      @ap: ATA port
+ *
+ *      Set up cable type and use generic probe init
+ */
+
+static int ns87410_pre_reset(struct ata_port *ap)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        static const struct pci_bits ns87410_enable_bits[] = {
+                { 0x43, 1, 0x08, 0x08 },
+                { 0x47, 1, 0x08, 0x08 }
+        };
+
+        if (!pci_test_config_bits(pdev, &ns87410_enable_bits[ap->port_no])) {
+                ata_port_disable(ap);
+                printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+                return 0;
+        }
+        ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      ns87410_error_handler           -       probe reset
+ *      @ap: ATA port
+ *
+ *      Perform the ATA probe and bus reset sequence plus specific handling
+ *      for this hardware. The MPIIX has the enable bits in a different place
+ *      to PIIX4 and friends. As a pure PIO device it has no cable detect
+ */
+
+static void ns87410_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, ns87410_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      ns87410_set_piomode     -       set initial PIO mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Program timing data. This is kept per channel not per device,
+ *      and only affects the data port.
+ */
+
+static void ns87410_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        int port = 0x40 + 4 * ap->port_no;
+        u8 idetcr, idefr;
+        struct ata_timing at;
+
+        static const u8 activebits[15] = {
+                0, 1, 2, 3, 4,
+                5, 5, 6, 6, 6,
+                6, 7, 7, 7, 7
+        };
+
+        static const u8 recoverbits[12] = {
+                0, 1, 2, 3, 4, 5, 6, 6, 7, 7, 7, 7
+        };
+
+        pci_read_config_byte(pdev, port + 3, &idefr);
+
+        if (ata_pio_need_iordy(adev))
+                idefr |= 0x04;  /* IORDY enable */
+        else
+                idefr &= ~0x04;
+
+        if (ata_timing_compute(adev, adev->pio_mode, &at, 30303, 1) < 0) {
+                dev_printk(KERN_ERR, &pdev->dev, "unknown mode %d.\n", adev->pio_mode);
+                return;
+        }
+
+        at.active = FIT(at.active, 2, 16) - 2;
+        at.setup = FIT(at.setup, 1, 4) - 1;
+        at.recover = FIT(at.recover, 1, 12) - 1;
+
+        idetcr = (at.setup << 6) | (recoverbits[at.recover] << 3) | activebits[at.active];
+
+        pci_write_config_byte(pdev, port, idetcr);
+        pci_write_config_byte(pdev, port + 3, idefr);
+        /* We use ap->private_data as a pointer to the device currently
+           loaded for timing */
+        ap->private_data = adev;
+}
+
+/**
+ *      ns87410_qc_issue_prot   -       command issue
+ *      @qc: command pending
+ *
+ *      Called when the libata layer is about to issue a command. We wrap
+ *      this interface so that we can load the correct ATA timings if
+ *      neccessary.
+ */
+
+static unsigned int ns87410_qc_issue_prot(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct ata_device *adev = qc->dev;
+
+        /* If modes have been configured and the channel data is not loaded
+           then load it. We have to check if pio_mode is set as the core code
+           does not set adev->pio_mode to XFER_PIO_0 while probing as would be
+           logical */
+
+        if (adev->pio_mode && adev != ap->private_data)
+                ns87410_set_piomode(ap, adev);
+
+        return ata_qc_issue_prot(qc);
+}
+
+static struct scsi_host_template ns87410_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations ns87410_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = ns87410_set_piomode,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = ns87410_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ns87410_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static int ns87410_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+        static struct ata_port_info info = {
+                .sht = &ns87410_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x0F,
+                .port_ops = &ns87410_port_ops
+        };
+        static struct ata_port_info *port_info[2] = {&info, &info};
+        return ata_pci_init_one(dev, port_info, 2);
+}
+
+static const struct pci_device_id ns87410[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87410), },
+        { 0, },
+};
+
+static struct pci_driver ns87410_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = ns87410,
+        .probe          = ns87410_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init ns87410_init(void)
+{
+        return pci_register_driver(&ns87410_pci_driver);
+}
+
+
+static void __exit ns87410_exit(void)
+{
+        pci_unregister_driver(&ns87410_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for Nat Semi 87410");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, ns87410);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(ns87410_init);
+module_exit(ns87410_exit);
diff --git a/drivers/ata/pata_oldpiix.c b/drivers/ata/pata_oldpiix.c
new file mode 100644
index 000000000000..04c618a2664b
--- /dev/null
+++ b/drivers/ata/pata_oldpiix.c
@@ -0,0 +1,339 @@
+/*
+ *    pata_oldpiix.c - Intel PATA/SATA controllers
+ *
+ *      (C) 2005 Red Hat <alan@redhat.com>
+ *
+ *    Some parts based on ata_piix.c by Jeff Garzik and others.
+ *
+ *    Early PIIX differs significantly from the later PIIX as it lacks
+ *    SITRE and the slave timing registers. This means that you have to
+ *    set timing per channel, or be clever. Libata tells us whenever it
+ *    does drive selection and we use this to reload the timings.
+ *
+ *    Because of these behaviour differences PIIX gets its own driver module.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/ata.h>
+
+#define DRV_NAME        "pata_oldpiix"
+#define DRV_VERSION     "0.5.1"
+
+/**
+ *      oldpiix_pre_reset               -       probe begin
+ *      @ap: ATA port
+ *
+ *      Set up cable type and use generic probe init
+ */
+
+static int oldpiix_pre_reset(struct ata_port *ap)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        static const struct pci_bits oldpiix_enable_bits[] = {
+                { 0x41U, 1U, 0x80UL, 0x80UL },  /* port 0 */
+                { 0x43U, 1U, 0x80UL, 0x80UL },  /* port 1 */
+        };
+
+        if (!pci_test_config_bits(pdev, &oldpiix_enable_bits[ap->port_no])) {
+                ata_port_disable(ap);
+                printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+                return 0;
+        }
+        ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      oldpiix_pata_error_handler - Probe specified port on PATA host controller
+ *      @ap: Port to probe
+ *      @classes:
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void oldpiix_pata_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, oldpiix_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      oldpiix_set_piomode - Initialize host controller PATA PIO timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: um
+ *
+ *      Set PIO mode for device, in host controller PCI config space.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void oldpiix_set_piomode (struct ata_port *ap, struct ata_device *adev)
+{
+        unsigned int pio        = adev->pio_mode - XFER_PIO_0;
+        struct pci_dev *dev     = to_pci_dev(ap->host->dev);
+        unsigned int idetm_port= ap->port_no ? 0x42 : 0x40;
+        u16 idetm_data;
+        int control = 0;
+
+        /*
+         *      See Intel Document 298600-004 for the timing programing rules
+         *      for PIIX/ICH. Note that the early PIIX does not have the slave
+         *      timing port at 0x44.
+         */
+
+        static const     /* ISP  RTC */
+        u8 timings[][2] = { { 0, 0 },
+                            { 0, 0 },
+                            { 1, 0 },
+                            { 2, 1 },
+                            { 2, 3 }, };
+
+        if (pio > 2)
+                control |= 1;   /* TIME1 enable */
+        if (ata_pio_need_iordy(adev))
+                control |= 2;   /* IE IORDY */
+
+        /* Intel specifies that the PPE functionality is for disk only */
+        if (adev->class == ATA_DEV_ATA)
+                control |= 4;   /* PPE enable */
+
+        pci_read_config_word(dev, idetm_port, &idetm_data);
+
+        /* Enable PPE, IE and TIME as appropriate. Clear the other
+           drive timing bits */
+        if (adev->devno == 0) {
+                idetm_data &= 0xCCE0;
+                idetm_data |= control;
+        } else {
+                idetm_data &= 0xCC0E;
+                idetm_data |= (control << 4);
+        }
+        idetm_data |= (timings[pio][0] << 12) |
+                        (timings[pio][1] << 8);
+        pci_write_config_word(dev, idetm_port, idetm_data);
+
+        /* Track which port is configured */
+        ap->private_data = adev;
+}
+
+/**
+ *      oldpiix_set_dmamode - Initialize host controller PATA DMA timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device to program
+ *      @isich: True if the device is an ICH and has IOCFG registers
+ *
+ *      Set MWDMA mode for device, in host controller PCI config space.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void oldpiix_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *dev     = to_pci_dev(ap->host->dev);
+        u8 idetm_port           = ap->port_no ? 0x42 : 0x40;
+        u16 idetm_data;
+
+        static const     /* ISP  RTC */
+        u8 timings[][2] = { { 0, 0 },
+                            { 0, 0 },
+                            { 1, 0 },
+                            { 2, 1 },
+                            { 2, 3 }, };
+
+        /*
+         * MWDMA is driven by the PIO timings. We must also enable
+         * IORDY unconditionally along with TIME1. PPE has already
+         * been set when the PIO timing was set.
+         */
+
+        unsigned int mwdma      = adev->dma_mode - XFER_MW_DMA_0;
+        unsigned int control;
+        const unsigned int needed_pio[3] = {
+                XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
+        };
+        int pio = needed_pio[mwdma] - XFER_PIO_0;
+
+        pci_read_config_word(dev, idetm_port, &idetm_data);
+
+        control = 3;    /* IORDY|TIME0 */
+        /* Intel specifies that the PPE functionality is for disk only */
+        if (adev->class == ATA_DEV_ATA)
+                control |= 4;   /* PPE enable */
+
+        /* If the drive MWDMA is faster than it can do PIO then
+           we must force PIO into PIO0 */
+
+        if (adev->pio_mode < needed_pio[mwdma])
+                /* Enable DMA timing only */
+                control |= 8;   /* PIO cycles in PIO0 */
+
+        /* Mask out the relevant control and timing bits we will load. Also
+           clear the other drive TIME register as a precaution */
+        if (adev->devno == 0) {
+                idetm_data &= 0xCCE0;
+                idetm_data |= control;
+        } else {
+                idetm_data &= 0xCC0E;
+                idetm_data |= (control << 4);
+        }
+        idetm_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8);
+        pci_write_config_word(dev, idetm_port, idetm_data);
+
+        /* Track which port is configured */
+        ap->private_data = adev;
+}
+
+/**
+ *      oldpiix_qc_issue_prot   -       command issue
+ *      @qc: command pending
+ *
+ *      Called when the libata layer is about to issue a command. We wrap
+ *      this interface so that we can load the correct ATA timings if
+ *      neccessary. Our logic also clears TIME0/TIME1 for the other device so
+ *      that, even if we get this wrong, cycles to the other device will
+ *      be made PIO0.
+ */
+
+static unsigned int oldpiix_qc_issue_prot(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct ata_device *adev = qc->dev;
+
+        if (adev != ap->private_data) {
+                if (adev->dma_mode)
+                        oldpiix_set_dmamode(ap, adev);
+                else if (adev->pio_mode)
+                        oldpiix_set_piomode(ap, adev);
+        }
+        return ata_qc_issue_prot(qc);
+}
+
+
+static struct scsi_host_template oldpiix_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static const struct ata_port_operations oldpiix_pata_ops = {
+        .port_disable           = ata_port_disable,
+        .set_piomode            = oldpiix_set_piomode,
+        .set_dmamode            = oldpiix_set_dmamode,
+        .mode_filter            = ata_pci_default_filter,
+
+        .tf_load                = ata_tf_load,
+        .tf_read                = ata_tf_read,
+        .check_status           = ata_check_status,
+        .exec_command           = ata_exec_command,
+        .dev_select             = ata_std_dev_select,
+
+        .freeze                 = ata_bmdma_freeze,
+        .thaw                   = ata_bmdma_thaw,
+        .error_handler          = oldpiix_pata_error_handler,
+        .post_internal_cmd      = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup            = ata_bmdma_setup,
+        .bmdma_start            = ata_bmdma_start,
+        .bmdma_stop             = ata_bmdma_stop,
+        .bmdma_status           = ata_bmdma_status,
+        .qc_prep                = ata_qc_prep,
+        .qc_issue               = oldpiix_qc_issue_prot,
+        .data_xfer              = ata_pio_data_xfer,
+
+        .irq_handler            = ata_interrupt,
+        .irq_clear              = ata_bmdma_irq_clear,
+
+        .port_start             = ata_port_start,
+        .port_stop              = ata_port_stop,
+        .host_stop              = ata_host_stop,
+};
+
+
+/**
+ *      oldpiix_init_one - Register PIIX ATA PCI device with kernel services
+ *      @pdev: PCI device to register
+ *      @ent: Entry in oldpiix_pci_tbl matching with @pdev
+ *
+ *      Called from kernel PCI layer.  We probe for combined mode (sigh),
+ *      and then hand over control to libata, for it to do the rest.
+ *
+ *      LOCKING:
+ *      Inherited from PCI layer (may sleep).
+ *
+ *      RETURNS:
+ *      Zero on success, or -ERRNO value.
+ */
+
+static int oldpiix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+        static int printed_version;
+        static struct ata_port_info info = {
+                .sht            = &oldpiix_sht,
+                .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask       = 0x1f, /* pio0-4 */
+                .mwdma_mask     = 0x07, /* mwdma1-2 */
+                .port_ops       = &oldpiix_pata_ops,
+        };
+        static struct ata_port_info *port_info[2] = { &info, &info };
+
+        if (!printed_version++)
+                dev_printk(KERN_DEBUG, &pdev->dev,
+                           "version " DRV_VERSION "\n");
+
+        return ata_pci_init_one(pdev, port_info, 2);
+}
+
+static const struct pci_device_id oldpiix_pci_tbl[] = {
+        { PCI_DEVICE(0x8086, 0x1230), },
+        { }     /* terminate list */
+};
+
+static struct pci_driver oldpiix_pci_driver = {
+        .name                   = DRV_NAME,
+        .id_table               = oldpiix_pci_tbl,
+        .probe                  = oldpiix_init_one,
+        .remove                 = ata_pci_remove_one,
+};
+
+static int __init oldpiix_init(void)
+{
+        return pci_register_driver(&oldpiix_pci_driver);
+}
+
+static void __exit oldpiix_exit(void)
+{
+        pci_unregister_driver(&oldpiix_pci_driver);
+}
+
+
+module_init(oldpiix_init);
+module_exit(oldpiix_exit);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("SCSI low-level driver for early PIIX series controllers");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, oldpiix_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+
diff --git a/drivers/ata/pata_opti.c b/drivers/ata/pata_opti.c
new file mode 100644
index 000000000000..c3d01325e0e2
--- /dev/null
+++ b/drivers/ata/pata_opti.c
@@ -0,0 +1,292 @@
+/*
+ * pata_opti.c  - ATI PATA for new ATA layer
+ *                        (C) 2005 Red Hat Inc
+ *                        Alan Cox <alan@redhat.com>
+ *
+ * Based on
+ *  linux/drivers/ide/pci/opti621.c             Version 0.7     Sept 10, 2002
+ *
+ *  Copyright (C) 1996-1998  Linus Torvalds & authors (see below)
+ *
+ * Authors:
+ * Jaromir Koutek <miri@punknet.cz>,
+ * Jan Harkes <jaharkes@cwi.nl>,
+ * Mark Lord <mlord@pobox.com>
+ * Some parts of code are from ali14xx.c and from rz1000.c.
+ *
+ * Also consulted the FreeBSD prototype driver by Kevin Day to try
+ * and resolve some confusions. Further documentation can be found in
+ * Ralf Brown's interrupt list
+ *
+ * If you have other variants of the Opti range (Viper/Vendetta) please
+ * try this driver with those PCI idents and report back. For the later
+ * chips see the pata_optidma driver
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_opti"
+#define DRV_VERSION "0.2.4"
+
+enum {
+        READ_REG        = 0,    /* index of Read cycle timing register */
+        WRITE_REG       = 1,    /* index of Write cycle timing register */
+        CNTRL_REG       = 3,    /* index of Control register */
+        STRAP_REG       = 5,    /* index of Strap register */
+        MISC_REG        = 6     /* index of Miscellaneous register */
+};
+
+/**
+ *      opti_pre_reset          -       probe begin
+ *      @ap: ATA port
+ *
+ *      Set up cable type and use generic probe init
+ */
+
+static int opti_pre_reset(struct ata_port *ap)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        static const struct pci_bits opti_enable_bits[] = {
+                { 0x45, 1, 0x80, 0x00 },
+                { 0x40, 1, 0x08, 0x00 }
+        };
+
+        if (!pci_test_config_bits(pdev, &opti_enable_bits[ap->port_no])) {
+                ata_port_disable(ap);
+                printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+                return 0;
+        }
+        ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      opti_probe_reset                -       probe reset
+ *      @ap: ATA port
+ *
+ *      Perform the ATA probe and bus reset sequence plus specific handling
+ *      for this hardware. The Opti needs little handling - we have no UDMA66
+ *      capability that needs cable detection. All we must do is check the port
+ *      is enabled.
+ */
+
+static void opti_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, opti_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      opti_write_reg          -       control register setup
+ *      @ap: ATA port
+ *      @value: value
+ *      @reg: control register number
+ *
+ *      The Opti uses magic 'trapdoor' register accesses to do configuration
+ *      rather than using PCI space as other controllers do. The double inw
+ *      on the error register activates configuration mode. We can then write
+ *      the control register
+ */
+
+static void opti_write_reg(struct ata_port *ap, u8 val, int reg)
+{
+        unsigned long regio = ap->ioaddr.cmd_addr;
+
+        /* These 3 unlock the control register access */
+        inw(regio + 1);
+        inw(regio + 1);
+        outb(3, regio + 2);
+
+        /* Do the I/O */
+        outb(val, regio + reg);
+
+        /* Relock */
+        outb(0x83, regio + 2);
+}
+
+#if 0
+/**
+ *      opti_read_reg           -       control register read
+ *      @ap: ATA port
+ *      @reg: control register number
+ *
+ *      The Opti uses magic 'trapdoor' register accesses to do configuration
+ *      rather than using PCI space as other controllers do. The double inw
+ *      on the error register activates configuration mode. We can then read
+ *      the control register
+ */
+
+static u8 opti_read_reg(struct ata_port *ap, int reg)
+{
+        unsigned long regio = ap->ioaddr.cmd_addr;
+        u8 ret;
+        inw(regio + 1);
+        inw(regio + 1);
+        outb(3, regio + 2);
+        ret = inb(regio + reg);
+        outb(0x83, regio + 2);
+}
+#endif
+
+/**
+ *      opti_set_piomode        -       set initial PIO mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Called to do the PIO mode setup. Timing numbers are taken from
+ *      the FreeBSD driver then pre computed to keep the code clean. There
+ *      are two tables depending on the hardware clock speed.
+ */
+
+static void opti_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct ata_device *pair = ata_dev_pair(adev);
+        int clock;
+        int pio = adev->pio_mode - XFER_PIO_0;
+        unsigned long regio = ap->ioaddr.cmd_addr;
+        u8 addr;
+
+        /* Address table precomputed with prefetch off and a DCLK of 2 */
+        static const u8 addr_timing[2][5] = {
+                { 0x30, 0x20, 0x20, 0x10, 0x10 },
+                { 0x20, 0x20, 0x10, 0x10, 0x10 }
+        };
+        static const u8 data_rec_timing[2][5] = {
+                { 0x6B, 0x56, 0x42, 0x32, 0x31 },
+                { 0x58, 0x44, 0x32, 0x22, 0x21 }
+        };
+
+        outb(0xff, regio + 5);
+        clock = inw(regio + 5) & 1;
+
+        /*
+         *      As with many controllers the address setup time is shared
+         *      and must suit both devices if present.
+         */
+
+        addr = addr_timing[clock][pio];
+        if (pair) {
+                /* Hardware constraint */
+                u8 pair_addr = addr_timing[clock][pair->pio_mode - XFER_PIO_0];
+                if (pair_addr > addr)
+                        addr = pair_addr;
+        }
+
+        /* Commence primary programming sequence */
+        opti_write_reg(ap, adev->devno, MISC_REG);
+        opti_write_reg(ap, data_rec_timing[clock][pio], READ_REG);
+        opti_write_reg(ap, data_rec_timing[clock][pio], WRITE_REG);
+        opti_write_reg(ap, addr, MISC_REG);
+
+        /* Programming sequence complete, override strapping */
+        opti_write_reg(ap, 0x85, CNTRL_REG);
+}
+
+static struct scsi_host_template opti_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations opti_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = opti_set_piomode,
+/*      .set_dmamode    = opti_set_dmamode, */
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = opti_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static int opti_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+        static struct ata_port_info info = {
+                .sht = &opti_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .port_ops = &opti_port_ops
+        };
+        static struct ata_port_info *port_info[2] = { &info, &info };
+        static int printed_version;
+
+        if (!printed_version++)
+                dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n");
+
+        return ata_pci_init_one(dev, port_info, 2);
+}
+
+static const struct pci_device_id opti[] = {
+        { PCI_VENDOR_ID_OPTI, PCI_DEVICE_ID_OPTI_82C621, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+        { PCI_VENDOR_ID_OPTI, PCI_DEVICE_ID_OPTI_82C825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
+        { 0, },
+};
+
+static struct pci_driver opti_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = opti,
+        .probe          = opti_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init opti_init(void)
+{
+        return pci_register_driver(&opti_pci_driver);
+}
+
+
+static void __exit opti_exit(void)
+{
+        pci_unregister_driver(&opti_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for Opti 621/621X");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, opti);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(opti_init);
+module_exit(opti_exit);
diff --git a/drivers/ata/pata_optidma.c b/drivers/ata/pata_optidma.c
new file mode 100644
index 000000000000..177a455f4251
--- /dev/null
+++ b/drivers/ata/pata_optidma.c
@@ -0,0 +1,547 @@
+/*
+ * pata_optidma.c       - Opti DMA PATA for new ATA layer
+ *                        (C) 2006 Red Hat Inc
+ *                        Alan Cox <alan@redhat.com>
+ *
+ *      The Opti DMA controllers are related to the older PIO PCI controllers
+ *      and indeed the VLB ones. The main differences are that the timing
+ *      numbers are now based off PCI clocks not VLB and differ, and that
+ *      MWDMA is supported.
+ *
+ *      This driver should support Viper-N+, FireStar, FireStar Plus.
+ *
+ *      These devices support virtual DMA for read (aka the CS5520). Later
+ *      chips support UDMA33, but only if the rest of the board logic does,
+ *      so you have to get this right. We don't support the virtual DMA
+ *      but we do handle UDMA.
+ *
+ *      Bits that are worth knowing
+ *              Most control registers are shadowed into I/O registers
+ *              0x1F5 bit 0 tells you if the PCI/VLB clock is 33 or 25Mhz
+ *              Virtual DMA registers *move* between rev 0x02 and rev 0x10
+ *              UDMA requires a 66MHz FSB
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_optidma"
+#define DRV_VERSION "0.2.1"
+
+enum {
+        READ_REG        = 0,    /* index of Read cycle timing register */
+        WRITE_REG       = 1,    /* index of Write cycle timing register */
+        CNTRL_REG       = 3,    /* index of Control register */
+        STRAP_REG       = 5,    /* index of Strap register */
+        MISC_REG        = 6     /* index of Miscellaneous register */
+};
+
+static int pci_clock;   /* 0 = 33 1 = 25 */
+
+/**
+ *      optidma_pre_reset               -       probe begin
+ *      @ap: ATA port
+ *
+ *      Set up cable type and use generic probe init
+ */
+
+static int optidma_pre_reset(struct ata_port *ap)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        static const struct pci_bits optidma_enable_bits = {
+                0x40, 1, 0x08, 0x00
+        };
+
+        if (ap->port_no && !pci_test_config_bits(pdev, &optidma_enable_bits)) {
+                ata_port_disable(ap);
+                printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+                return 0;
+        }
+        ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      optidma_probe_reset             -       probe reset
+ *      @ap: ATA port
+ *
+ *      Perform the ATA probe and bus reset sequence plus specific handling
+ *      for this hardware. The Opti needs little handling - we have no UDMA66
+ *      capability that needs cable detection. All we must do is check the port
+ *      is enabled.
+ */
+
+static void optidma_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, optidma_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      optidma_unlock          -       unlock control registers
+ *      @ap: ATA port
+ *
+ *      Unlock the control register block for this adapter. Registers must not
+ *      be unlocked in a situation where libata might look at them.
+ */
+
+static void optidma_unlock(struct ata_port *ap)
+{
+        unsigned long regio = ap->ioaddr.cmd_addr;
+
+        /* These 3 unlock the control register access */
+        inw(regio + 1);
+        inw(regio + 1);
+        outb(3, regio + 2);
+}
+
+/**
+ *      optidma_lock            -       issue temporary relock
+ *      @ap: ATA port
+ *
+ *      Re-lock the configuration register settings.
+ */
+
+static void optidma_lock(struct ata_port *ap)
+{
+        unsigned long regio = ap->ioaddr.cmd_addr;
+
+        /* Relock */
+        outb(0x83, regio + 2);
+}
+
+/**
+ *      optidma_set_mode        -       set mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *      @mode: Mode to set
+ *
+ *      Called to do the DMA or PIO mode setup. Timing numbers are all
+ *      pre computed to keep the code clean. There are two tables depending
+ *      on the hardware clock speed.
+ *
+ *      WARNING: While we do this the IDE registers vanish. If we take an
+ *      IRQ here we depend on the host set locking to avoid catastrophe.
+ */
+
+static void optidma_set_mode(struct ata_port *ap, struct ata_device *adev, u8 mode)
+{
+        struct ata_device *pair = ata_dev_pair(adev);
+        int pio = adev->pio_mode - XFER_PIO_0;
+        int dma = adev->dma_mode - XFER_MW_DMA_0;
+        unsigned long regio = ap->ioaddr.cmd_addr;
+        u8 addr;
+
+        /* Address table precomputed with a DCLK of 2 */
+        static const u8 addr_timing[2][5] = {
+                { 0x30, 0x20, 0x20, 0x10, 0x10 },
+                { 0x20, 0x20, 0x10, 0x10, 0x10 }
+        };
+        static const u8 data_rec_timing[2][5] = {
+                { 0x59, 0x46, 0x30, 0x20, 0x20 },
+                { 0x46, 0x32, 0x20, 0x20, 0x10 }
+        };
+        static const u8 dma_data_rec_timing[2][3] = {
+                { 0x76, 0x20, 0x20 },
+                { 0x54, 0x20, 0x10 }
+        };
+
+        /* Switch from IDE to control mode */
+        optidma_unlock(ap);
+
+
+        /*
+         *      As with many controllers the address setup time is shared
+         *      and must suit both devices if present. FIXME: Check if we
+         *      need to look at slowest of PIO/DMA mode of either device
+         */
+
+        if (mode >= XFER_MW_DMA_0)
+                addr = 0;
+        else
+                addr = addr_timing[pci_clock][pio];
+
+        if (pair) {
+                u8 pair_addr;
+                /* Hardware constraint */
+                if (pair->dma_mode)
+                        pair_addr = 0;
+                else
+                        pair_addr = addr_timing[pci_clock][pair->pio_mode - XFER_PIO_0];
+                if (pair_addr > addr)
+                        addr = pair_addr;
+        }
+
+        /* Commence primary programming sequence */
+        /* First we load the device number into the timing select */
+        outb(adev->devno, regio + MISC_REG);
+        /* Now we load the data timings into read data/write data */
+        if (mode < XFER_MW_DMA_0) {
+                outb(data_rec_timing[pci_clock][pio], regio + READ_REG);
+                outb(data_rec_timing[pci_clock][pio], regio + WRITE_REG);
+        } else if (mode < XFER_UDMA_0) {
+                outb(dma_data_rec_timing[pci_clock][dma], regio + READ_REG);
+                outb(dma_data_rec_timing[pci_clock][dma], regio + WRITE_REG);
+        }
+        /* Finally we load the address setup into the misc register */
+        outb(addr | adev->devno, regio + MISC_REG);
+
+        /* Programming sequence complete, timing 0 dev 0, timing 1 dev 1 */
+        outb(0x85, regio + CNTRL_REG);
+
+        /* Switch back to IDE mode */
+        optidma_lock(ap);
+
+        /* Note: at this point our programming is incomplete. We are
+           not supposed to program PCI 0x43 "things we hacked onto the chip"
+           until we've done both sets of PIO/DMA timings */
+}
+
+/**
+ *      optiplus_set_mode       -       DMA setup for Firestar Plus
+ *      @ap: ATA port
+ *      @adev: device
+ *      @mode: desired mode
+ *
+ *      The Firestar plus has additional UDMA functionality for UDMA0-2 and
+ *      requires we do some additional work. Because the base work we must do
+ *      is mostly shared we wrap the Firestar setup functionality in this
+ *      one
+ */
+
+static void optiplus_set_mode(struct ata_port *ap, struct ata_device *adev, u8 mode)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u8 udcfg;
+        u8 udslave;
+        int dev2 = 2 * adev->devno;
+        int unit = 2 * ap->port_no + adev->devno;
+        int udma = mode - XFER_UDMA_0;
+
+        pci_read_config_byte(pdev, 0x44, &udcfg);
+        if (mode <= XFER_UDMA_0) {
+                udcfg &= ~(1 << unit);
+                optidma_set_mode(ap, adev, adev->dma_mode);
+        } else {
+                udcfg |=  (1 << unit);
+                if (ap->port_no) {
+                        pci_read_config_byte(pdev, 0x45, &udslave);
+                        udslave &= ~(0x03 << dev2);
+                        udslave |= (udma << dev2);
+                        pci_write_config_byte(pdev, 0x45, udslave);
+                } else {
+                        udcfg &= ~(0x30 << dev2);
+                        udcfg |= (udma << dev2);
+                }
+        }
+        pci_write_config_byte(pdev, 0x44, udcfg);
+}
+
+/**
+ *      optidma_set_pio_mode    -       PIO setup callback
+ *      @ap: ATA port
+ *      @adev: Device
+ *
+ *      The libata core provides separate functions for handling PIO and
+ *      DMA programming. The architecture of the Firestar makes it easier
+ *      for us to have a common function so we provide wrappers
+ */
+
+static void optidma_set_pio_mode(struct ata_port *ap, struct ata_device *adev)
+{
+        optidma_set_mode(ap, adev, adev->pio_mode);
+}
+
+/**
+ *      optidma_set_dma_mode    -       DMA setup callback
+ *      @ap: ATA port
+ *      @adev: Device
+ *
+ *      The libata core provides separate functions for handling PIO and
+ *      DMA programming. The architecture of the Firestar makes it easier
+ *      for us to have a common function so we provide wrappers
+ */
+
+static void optidma_set_dma_mode(struct ata_port *ap, struct ata_device *adev)
+{
+        optidma_set_mode(ap, adev, adev->dma_mode);
+}
+
+/**
+ *      optiplus_set_pio_mode   -       PIO setup callback
+ *      @ap: ATA port
+ *      @adev: Device
+ *
+ *      The libata core provides separate functions for handling PIO and
+ *      DMA programming. The architecture of the Firestar makes it easier
+ *      for us to have a common function so we provide wrappers
+ */
+
+static void optiplus_set_pio_mode(struct ata_port *ap, struct ata_device *adev)
+{
+        optiplus_set_mode(ap, adev, adev->pio_mode);
+}
+
+/**
+ *      optiplus_set_dma_mode   -       DMA setup callback
+ *      @ap: ATA port
+ *      @adev: Device
+ *
+ *      The libata core provides separate functions for handling PIO and
+ *      DMA programming. The architecture of the Firestar makes it easier
+ *      for us to have a common function so we provide wrappers
+ */
+
+static void optiplus_set_dma_mode(struct ata_port *ap, struct ata_device *adev)
+{
+        optiplus_set_mode(ap, adev, adev->dma_mode);
+}
+
+/**
+ *      optidma_make_bits       -       PCI setup helper
+ *      @adev: ATA device
+ *
+ *      Turn the ATA device setup into PCI configuration bits
+ *      for register 0x43 and return the two bits needed.
+ */
+
+static u8 optidma_make_bits43(struct ata_device *adev)
+{
+        static const u8 bits43[5] = {
+                0, 0, 0, 1, 2
+        };
+        if (!ata_dev_enabled(adev))
+                return 0;
+        if (adev->dma_mode)
+                return adev->dma_mode - XFER_MW_DMA_0;
+        return bits43[adev->pio_mode - XFER_PIO_0];
+}
+
+/**
+ *      optidma_post_set_mode   -       finalize PCI setup
+ *      @ap: port to set up
+ *
+ *      Finalise the configuration by writing the nibble of extra bits
+ *      of data into the chip.
+ */
+
+static void optidma_post_set_mode(struct ata_port *ap)
+{
+        u8 r;
+        int nybble = 4 * ap->port_no;
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+        pci_read_config_byte(pdev, 0x43, &r);
+
+        r &= (0x0F << nybble);
+        r |= (optidma_make_bits43(&ap->device[0]) +
+             (optidma_make_bits43(&ap->device[0]) << 2)) << nybble;
+
+        pci_write_config_byte(pdev, 0x43, r);
+}
+
+static struct scsi_host_template optidma_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations optidma_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = optidma_set_pio_mode,
+        .set_dmamode    = optidma_set_dma_mode,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+        .error_handler  = optidma_error_handler,
+        .post_set_mode  = optidma_post_set_mode,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static struct ata_port_operations optiplus_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = optiplus_set_pio_mode,
+        .set_dmamode    = optiplus_set_dma_mode,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+        .error_handler  = optidma_error_handler,
+        .post_set_mode  = optidma_post_set_mode,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/**
+ *      optiplus_with_udma      -       Look for UDMA capable setup
+ *      @pdev; ATA controller
+ */
+
+static int optiplus_with_udma(struct pci_dev *pdev)
+{
+        u8 r;
+        int ret = 0;
+        int ioport = 0x22;
+        struct pci_dev *dev1;
+
+        /* Find function 1 */
+        dev1 = pci_get_device(0x1045, 0xC701, NULL);
+        if(dev1 == NULL)
+                return 0;
+
+        /* Rev must be >= 0x10 */
+        pci_read_config_byte(dev1, 0x08, &r);
+        if (r < 0x10)
+                goto done_nomsg;
+        /* Read the chipset system configuration to check our mode */
+        pci_read_config_byte(dev1, 0x5F, &r);
+        ioport |= (r << 8);
+        outb(0x10, ioport);
+        /* Must be 66Mhz sync */
+        if ((inb(ioport + 2) & 1) == 0)
+                goto done;
+
+        /* Check the ATA arbitration/timing is suitable */
+        pci_read_config_byte(pdev, 0x42, &r);
+        if ((r & 0x36) != 0x36)
+                goto done;
+        pci_read_config_byte(dev1, 0x52, &r);
+        if (r & 0x80)   /* IDEDIR disabled */
+                ret = 1;
+done:
+        printk(KERN_WARNING "UDMA not supported in this configuration.\n");
+done_nomsg:             /* Wrong chip revision */
+        pci_dev_put(dev1);
+        return ret;
+}
+
+static int optidma_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+        static struct ata_port_info info_82c700 = {
+                .sht = &optidma_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .port_ops = &optidma_port_ops
+        };
+        static struct ata_port_info info_82c700_udma = {
+                .sht = &optidma_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x07,
+                .port_ops = &optiplus_port_ops
+        };
+        static struct ata_port_info *port_info[2];
+        struct ata_port_info *info = &info_82c700;
+        static int printed_version;
+
+        if (!printed_version++)
+                dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n");
+
+        /* Fixed location chipset magic */
+        inw(0x1F1);
+        inw(0x1F1);
+        pci_clock = inb(0x1F5) & 1;             /* 0 = 33Mhz, 1 = 25Mhz */
+
+        if (optiplus_with_udma(dev))
+                info = &info_82c700_udma;
+
+        port_info[0] = port_info[1] = info;
+        return ata_pci_init_one(dev, port_info, 2);
+}
+
+static const struct pci_device_id optidma[] = {
+        { PCI_DEVICE(0x1045, 0xD568), },        /* Opti 82C700 */
+        { 0, },
+};
+
+static struct pci_driver optidma_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = optidma,
+        .probe          = optidma_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init optidma_init(void)
+{
+        return pci_register_driver(&optidma_pci_driver);
+}
+
+
+static void __exit optidma_exit(void)
+{
+        pci_unregister_driver(&optidma_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for Opti Firestar/Firestar Plus");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, optidma);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(optidma_init);
+module_exit(optidma_exit);
diff --git a/drivers/ata/pata_pcmcia.c b/drivers/ata/pata_pcmcia.c
new file mode 100644
index 000000000000..62b25cda409b
--- /dev/null
+++ b/drivers/ata/pata_pcmcia.c
@@ -0,0 +1,393 @@
+/*
+ *   pata_pcmcia.c - PCMCIA PATA controller driver.
+ *   Copyright 2005-2006 Red Hat Inc <alan@redhat.com>, all rights reserved.
+ *   PCMCIA ident update Copyright 2006 Marcin Juszkiewicz
+ *                                              <openembedded@hrw.one.pl>
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2, or (at your option)
+ *  any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; see the file COPYING.  If not, write to
+ *  the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *   Heavily based upon ide-cs.c
+ *   The initial developer of the original code is David A. Hinds
+ *   <dahinds@users.sourceforge.net>.  Portions created by David A. Hinds
+ *   are Copyright (C) 1999 David A. Hinds.  All Rights Reserved.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/ata.h>
+#include <linux/libata.h>
+
+#include <pcmcia/cs_types.h>
+#include <pcmcia/cs.h>
+#include <pcmcia/cistpl.h>
+#include <pcmcia/ds.h>
+#include <pcmcia/cisreg.h>
+#include <pcmcia/ciscode.h>
+
+
+#define DRV_NAME "pata_pcmcia"
+#define DRV_VERSION "0.2.9"
+
+/*
+ *      Private data structure to glue stuff together
+ */
+
+struct ata_pcmcia_info {
+        struct pcmcia_device *pdev;
+        int             ndev;
+        dev_node_t      node;
+};
+
+static struct scsi_host_template pcmcia_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations pcmcia_port_ops = {
+        .port_disable   = ata_port_disable,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = ata_bmdma_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer_noirq,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+#define CS_CHECK(fn, ret) \
+do { last_fn = (fn); if ((last_ret = (ret)) != 0) goto cs_failed; } while (0)
+
+/**
+ *      pcmcia_init_one         -       attach a PCMCIA interface
+ *      @pdev: pcmcia device
+ *
+ *      Register a PCMCIA IDE interface. Such interfaces are PIO 0 and
+ *      shared IRQ.
+ */
+
+static int pcmcia_init_one(struct pcmcia_device *pdev)
+{
+        struct ata_probe_ent ae;
+        struct ata_pcmcia_info *info;
+        tuple_t tuple;
+        struct {
+                unsigned short buf[128];
+                cisparse_t parse;
+                config_info_t conf;
+                cistpl_cftable_entry_t dflt;
+        } *stk = NULL;
+        cistpl_cftable_entry_t *cfg;
+        int pass, last_ret = 0, last_fn = 0, is_kme = 0, ret = -ENOMEM;
+        unsigned long io_base, ctl_base;
+
+        info = kzalloc(sizeof(*info), GFP_KERNEL);
+        if (info == NULL)
+                return -ENOMEM;
+
+        /* Glue stuff together. FIXME: We may be able to get rid of info with care */
+        info->pdev = pdev;
+        pdev->priv = info;
+
+        /* Set up attributes in order to probe card and get resources */
+        pdev->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
+        pdev->io.Attributes2 = IO_DATA_PATH_WIDTH_8;
+        pdev->io.IOAddrLines = 3;
+        pdev->irq.Attributes = IRQ_TYPE_DYNAMIC_SHARING;
+        pdev->irq.IRQInfo1 = IRQ_LEVEL_ID;
+        pdev->conf.Attributes = CONF_ENABLE_IRQ;
+        pdev->conf.IntType = INT_MEMORY_AND_IO;
+
+        /* Allocate resoure probing structures */
+
+        stk = kzalloc(sizeof(*stk), GFP_KERNEL);
+        if (!stk)
+                goto out1;
+
+        cfg = &stk->parse.cftable_entry;
+
+        /* Tuples we are walking */
+        tuple.TupleData = (cisdata_t *)&stk->buf;
+        tuple.TupleOffset = 0;
+        tuple.TupleDataMax = 255;
+        tuple.Attributes = 0;
+        tuple.DesiredTuple = CISTPL_CONFIG;
+
+        CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(pdev, &tuple));
+        CS_CHECK(GetTupleData, pcmcia_get_tuple_data(pdev, &tuple));
+        CS_CHECK(ParseTuple, pcmcia_parse_tuple(pdev, &tuple, &stk->parse));
+        pdev->conf.ConfigBase = stk->parse.config.base;
+        pdev->conf.Present = stk->parse.config.rmask[0];
+
+        /* See if we have a manufacturer identifier. Use it to set is_kme for
+           vendor quirks */
+        tuple.DesiredTuple = CISTPL_MANFID;
+        if (!pcmcia_get_first_tuple(pdev, &tuple) && !pcmcia_get_tuple_data(pdev, &tuple) && !pcmcia_parse_tuple(pdev, &tuple, &stk->parse))
+                        is_kme = ((stk->parse.manfid.manf == MANFID_KME) && ((stk->parse.manfid.card == PRODID_KME_KXLC005_A) || (stk->parse.manfid.card == PRODID_KME_KXLC005_B)));
+
+        /* Not sure if this is right... look up the current Vcc */
+        CS_CHECK(GetConfigurationInfo, pcmcia_get_configuration_info(pdev, &stk->conf));
+/*      link->conf.Vcc = stk->conf.Vcc; */
+
+        pass = io_base = ctl_base = 0;
+        tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
+        tuple.Attributes = 0;
+        CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(pdev, &tuple));
+
+        /* Now munch the resources looking for a suitable set */
+        while (1) {
+                if (pcmcia_get_tuple_data(pdev, &tuple) != 0)
+                        goto next_entry;
+                if (pcmcia_parse_tuple(pdev, &tuple, &stk->parse) != 0)
+                        goto next_entry;
+                /* Check for matching Vcc, unless we're desperate */
+                if (!pass) {
+                        if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) {
+                                if (stk->conf.Vcc != cfg->vcc.param[CISTPL_POWER_VNOM] / 10000)
+                                        goto next_entry;
+                        } else if (stk->dflt.vcc.present & (1 << CISTPL_POWER_VNOM)) {
+                                if (stk->conf.Vcc != stk->dflt.vcc.param[CISTPL_POWER_VNOM] / 10000)
+                                        goto next_entry;
+                        }
+                }
+
+                if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM))
+                        pdev->conf.Vpp = cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000;
+                else if (stk->dflt.vpp1.present & (1 << CISTPL_POWER_VNOM))
+                        pdev->conf.Vpp = stk->dflt.vpp1.param[CISTPL_POWER_VNOM] / 10000;
+
+                if ((cfg->io.nwin > 0) || (stk->dflt.io.nwin > 0)) {
+                        cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &stk->dflt.io;
+                        pdev->conf.ConfigIndex = cfg->index;
+                        pdev->io.BasePort1 = io->win[0].base;
+                        pdev->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
+                        if (!(io->flags & CISTPL_IO_16BIT))
+                                pdev->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
+                        if (io->nwin == 2) {
+                                pdev->io.NumPorts1 = 8;
+                                pdev->io.BasePort2 = io->win[1].base;
+                                pdev->io.NumPorts2 = (is_kme) ? 2 : 1;
+                                if (pcmcia_request_io(pdev, &pdev->io) != 0)
+                                        goto next_entry;
+                                io_base = pdev->io.BasePort1;
+                                ctl_base = pdev->io.BasePort2;
+                        } else if ((io->nwin == 1) && (io->win[0].len >= 16)) {
+                                pdev->io.NumPorts1 = io->win[0].len;
+                                pdev->io.NumPorts2 = 0;
+                                if (pcmcia_request_io(pdev, &pdev->io) != 0)
+                                        goto next_entry;
+                                io_base = pdev->io.BasePort1;
+                                ctl_base = pdev->io.BasePort1 + 0x0e;
+                        } else goto next_entry;
+                        /* If we've got this far, we're done */
+                        break;
+                }
+next_entry:
+                if (cfg->flags & CISTPL_CFTABLE_DEFAULT)
+                        memcpy(&stk->dflt, cfg, sizeof(stk->dflt));
+                if (pass) {
+                        CS_CHECK(GetNextTuple, pcmcia_get_next_tuple(pdev, &tuple));
+                } else if (pcmcia_get_next_tuple(pdev, &tuple) != 0) {
+                        CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(pdev, &tuple));
+                        memset(&stk->dflt, 0, sizeof(stk->dflt));
+                        pass++;
+                }
+        }
+
+        CS_CHECK(RequestIRQ, pcmcia_request_irq(pdev, &pdev->irq));
+        CS_CHECK(RequestConfiguration, pcmcia_request_configuration(pdev, &pdev->conf));
+
+        /* Success. Disable the IRQ nIEN line, do quirks */
+        outb(0x02, ctl_base);
+        if (is_kme)
+                outb(0x81, ctl_base + 0x01);
+
+        /* FIXME: Could be more ports at base + 0x10 but we only deal with
+           one right now */
+        if (pdev->io.NumPorts1 >= 0x20)
+                printk(KERN_WARNING DRV_NAME ": second channel not yet supported.\n");
+
+        /*
+         *      Having done the PCMCIA plumbing the ATA side is relatively
+         *      sane.
+         */
+
+        memset(&ae, 0, sizeof(struct ata_probe_ent));
+        INIT_LIST_HEAD(&ae.node);
+        ae.dev = &pdev->dev;
+        ae.port_ops = &pcmcia_port_ops;
+        ae.sht = &pcmcia_sht;
+        ae.n_ports = 1;
+        ae.pio_mask = 1;                /* ISA so PIO 0 cycles */
+        ae.irq = pdev->irq.AssignedIRQ;
+        ae.irq_flags = SA_SHIRQ;
+        ae.port_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST;
+        ae.port[0].cmd_addr = io_base;
+        ae.port[0].altstatus_addr = ctl_base;
+        ae.port[0].ctl_addr = ctl_base;
+        ata_std_ports(&ae.port[0]);
+
+        if (ata_device_add(&ae) == 0)
+                goto failed;
+
+        info->ndev = 1;
+        kfree(stk);
+        return 0;
+
+cs_failed:
+        cs_error(pdev, last_fn, last_ret);
+failed:
+        kfree(stk);
+        info->ndev = 0;
+        pcmcia_disable_device(pdev);
+out1:
+        kfree(info);
+        return ret;
+}
+
+/**
+ *      pcmcia_remove_one       -       unplug an pcmcia interface
+ *      @pdev: pcmcia device
+ *
+ *      A PCMCIA ATA device has been unplugged. Perform the needed
+ *      cleanup. Also called on module unload for any active devices.
+ */
+
+static void pcmcia_remove_one(struct pcmcia_device *pdev)
+{
+        struct ata_pcmcia_info *info = pdev->priv;
+        struct device *dev = &pdev->dev;
+
+        if (info != NULL) {
+                /* If we have attached the device to the ATA layer, detach it */
+                if (info->ndev) {
+                        struct ata_host *host = dev_get_drvdata(dev);
+                        ata_host_remove(host);
+                        dev_set_drvdata(dev, NULL);
+                }
+                info->ndev = 0;
+                pdev->priv = NULL;
+        }
+        pcmcia_disable_device(pdev);
+        kfree(info);
+}
+
+static struct pcmcia_device_id pcmcia_devices[] = {
+        PCMCIA_DEVICE_FUNC_ID(4),
+        PCMCIA_DEVICE_MANF_CARD(0x0007, 0x0000),        /* Hitachi */
+        PCMCIA_DEVICE_MANF_CARD(0x0032, 0x0704),
+        PCMCIA_DEVICE_MANF_CARD(0x0045, 0x0401),
+        PCMCIA_DEVICE_MANF_CARD(0x0098, 0x0000),        /* Toshiba */
+        PCMCIA_DEVICE_MANF_CARD(0x00a4, 0x002d),
+        PCMCIA_DEVICE_MANF_CARD(0x00ce, 0x0000),        /* Samsung */
+        PCMCIA_DEVICE_MANF_CARD(0x0319, 0x0000),        /* Hitachi */
+        PCMCIA_DEVICE_MANF_CARD(0x2080, 0x0001),
+        PCMCIA_DEVICE_MANF_CARD(0x4e01, 0x0200),        /* Lexar */
+        PCMCIA_DEVICE_PROD_ID123("Caravelle", "PSC-IDE ", "PSC000", 0x8c36137c, 0xd0693ab8, 0x2768a9f0),
+        PCMCIA_DEVICE_PROD_ID123("CDROM", "IDE", "MCD-601p", 0x1b9179ca, 0xede88951, 0x0d902f74),
+        PCMCIA_DEVICE_PROD_ID123("PCMCIA", "IDE CARD", "F1", 0x281f1c5d, 0x1907960c, 0xf7fde8b9),
+        PCMCIA_DEVICE_PROD_ID12("ARGOSY", "CD-ROM", 0x78f308dc, 0x66536591),
+        PCMCIA_DEVICE_PROD_ID12("ARGOSY", "PnPIDE", 0x78f308dc, 0x0c694728),
+        PCMCIA_DEVICE_PROD_ID12("CNF CD-M", "CD-ROM", 0x7d93b852, 0x66536591),
+        PCMCIA_DEVICE_PROD_ID12("Creative Technology Ltd.", "PCMCIA CD-ROM Interface Card", 0xff8c8a45, 0xfe8020c4),
+        PCMCIA_DEVICE_PROD_ID12("Digital Equipment Corporation.", "Digital Mobile Media CD-ROM", 0x17692a66, 0xef1dcbde),
+        PCMCIA_DEVICE_PROD_ID12("EXP", "CD+GAME", 0x6f58c983, 0x63c13aaf),
+        PCMCIA_DEVICE_PROD_ID12("EXP   ", "CD-ROM", 0x0a5c52fd, 0x66536591),
+        PCMCIA_DEVICE_PROD_ID12("EXP   ", "PnPIDE", 0x0a5c52fd, 0x0c694728),
+        PCMCIA_DEVICE_PROD_ID12("FREECOM", "PCCARD-IDE", 0x5714cbf7, 0x48e0ab8e),
+        PCMCIA_DEVICE_PROD_ID12("HITACHI", "FLASH", 0xf4f43949, 0x9eb86aae),
+        PCMCIA_DEVICE_PROD_ID12("HITACHI", "microdrive", 0xf4f43949, 0xa6d76178),
+        PCMCIA_DEVICE_PROD_ID12("IBM", "microdrive", 0xb569a6e5, 0xa6d76178),
+        PCMCIA_DEVICE_PROD_ID12("IBM", "IBM17JSSFP20", 0xb569a6e5, 0xf2508753),
+        PCMCIA_DEVICE_PROD_ID12("IO DATA", "CBIDE2      ", 0x547e66dc, 0x8671043b),
+        PCMCIA_DEVICE_PROD_ID12("IO DATA", "PCIDE", 0x547e66dc, 0x5c5ab149),
+        PCMCIA_DEVICE_PROD_ID12("IO DATA", "PCIDEII", 0x547e66dc, 0xb3662674),
+        PCMCIA_DEVICE_PROD_ID12("LOOKMEET", "CBIDE2      ", 0xe37be2b5, 0x8671043b),
+        PCMCIA_DEVICE_PROD_ID12("M-Systems", "CF500", 0x7ed2ad87, 0x7a13045c),
+        PCMCIA_DEVICE_PROD_ID2("NinjaATA-", 0xebe0bd79),
+        PCMCIA_DEVICE_PROD_ID12("PCMCIA", "CD-ROM", 0x281f1c5d, 0x66536591),
+        PCMCIA_DEVICE_PROD_ID12("PCMCIA", "PnPIDE", 0x281f1c5d, 0x0c694728),
+        PCMCIA_DEVICE_PROD_ID12("SHUTTLE TECHNOLOGY LTD.", "PCCARD-IDE/ATAPI Adapter", 0x4a3f0ba0, 0x322560e1),
+        PCMCIA_DEVICE_PROD_ID12("SEAGATE", "ST1", 0x87c1b330, 0xe1f30883),
+        PCMCIA_DEVICE_PROD_ID12("SAMSUNG", "04/05/06", 0x43d74cb4, 0x6a22777d),
+        PCMCIA_DEVICE_PROD_ID12("SMI VENDOR", "SMI PRODUCT", 0x30896c92, 0x703cc5f6),
+        PCMCIA_DEVICE_PROD_ID12("TOSHIBA", "MK2001MPL", 0xb4585a1a, 0x3489e003),
+        PCMCIA_DEVICE_PROD_ID12("WIT", "IDE16", 0x244e5994, 0x3e232852),
+        PCMCIA_DEVICE_PROD_ID1("STI Flash", 0xe4a13209),
+        PCMCIA_DEVICE_PROD_ID12("STI", "Flash 5.0", 0xbf2df18d, 0x8cb57a0e),
+        PCMCIA_MFC_DEVICE_PROD_ID12(1, "SanDisk", "ConnectPlus", 0x7a954bd9, 0x74be00c6),
+        PCMCIA_DEVICE_NULL,
+};
+
+MODULE_DEVICE_TABLE(pcmcia, pcmcia_devices);
+
+static struct pcmcia_driver pcmcia_driver = {
+        .owner          = THIS_MODULE,
+        .drv = {
+                .name           = DRV_NAME,
+        },
+        .id_table       = pcmcia_devices,
+        .probe          = pcmcia_init_one,
+        .remove         = pcmcia_remove_one,
+};
+
+static int __init pcmcia_init(void)
+{
+        return pcmcia_register_driver(&pcmcia_driver);
+}
+
+static void __exit pcmcia_exit(void)
+{
+        pcmcia_unregister_driver(&pcmcia_driver);
+}
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for PCMCIA ATA");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
+
+module_init(pcmcia_init);
+module_exit(pcmcia_exit);
diff --git a/drivers/ata/pata_pdc2027x.c b/drivers/ata/pata_pdc2027x.c
new file mode 100644
index 000000000000..56b8c1ee2937
--- /dev/null
+++ b/drivers/ata/pata_pdc2027x.c
@@ -0,0 +1,869 @@
+/*
+ *  Promise PATA TX2/TX4/TX2000/133 IDE driver for pdc20268 to pdc20277.
+ *
+ *  This program is free software; you can redistribute it and/or
+ *  modify it under the terms of the GNU General Public License
+ *  as published by the Free Software Foundation; either version
+ *  2 of the License, or (at your option) any later version.
+ *
+ *  Ported to libata by:
+ *  Albert Lee <albertcc@tw.ibm.com> IBM Corporation
+ *
+ *  Copyright (C) 1998-2002             Andre Hedrick <andre@linux-ide.org>
+ *  Portions Copyright (C) 1999 Promise Technology, Inc.
+ *
+ *  Author: Frank Tiernan (frankt@promise.com)
+ *  Released under terms of General Public License
+ *
+ *
+ *  libata documentation is available via 'make {ps|pdf}docs',
+ *  as Documentation/DocBook/libata.*
+ *
+ *  Hardware information only available under NDA.
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi.h>
+#include <scsi/scsi_host.h>
+#include <scsi/scsi_cmnd.h>
+#include <linux/libata.h>
+#include <asm/io.h>
+
+#define DRV_NAME        "pata_pdc2027x"
+#define DRV_VERSION     "0.74-ac3"
+#undef PDC_DEBUG
+
+#ifdef PDC_DEBUG
+#define PDPRINTK(fmt, args...) printk(KERN_ERR "%s: " fmt, __FUNCTION__, ## args)
+#else
+#define PDPRINTK(fmt, args...)
+#endif
+
+enum {
+        PDC_UDMA_100            = 0,
+        PDC_UDMA_133            = 1,
+
+        PDC_100_MHZ             = 100000000,
+        PDC_133_MHZ             = 133333333,
+
+        PDC_SYS_CTL             = 0x1100,
+        PDC_ATA_CTL             = 0x1104,
+        PDC_GLOBAL_CTL          = 0x1108,
+        PDC_CTCR0               = 0x110C,
+        PDC_CTCR1               = 0x1110,
+        PDC_BYTE_COUNT          = 0x1120,
+        PDC_PLL_CTL             = 0x1202,
+};
+
+static int pdc2027x_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
+static void pdc2027x_remove_one(struct pci_dev *pdev);
+static void pdc2027x_error_handler(struct ata_port *ap);
+static void pdc2027x_set_piomode(struct ata_port *ap, struct ata_device *adev);
+static void pdc2027x_set_dmamode(struct ata_port *ap, struct ata_device *adev);
+static void pdc2027x_post_set_mode(struct ata_port *ap);
+static int pdc2027x_check_atapi_dma(struct ata_queued_cmd *qc);
+
+/*
+ * ATA Timing Tables based on 133MHz controller clock.
+ * These tables are only used when the controller is in 133MHz clock.
+ * If the controller is in 100MHz clock, the ASIC hardware will
+ * set the timing registers automatically when "set feature" command
+ * is issued to the device. However, if the controller clock is 133MHz,
+ * the following tables must be used.
+ */
+static struct pdc2027x_pio_timing {
+        u8 value0, value1, value2;
+} pdc2027x_pio_timing_tbl [] = {
+        { 0xfb, 0x2b, 0xac }, /* PIO mode 0 */
+        { 0x46, 0x29, 0xa4 }, /* PIO mode 1 */
+        { 0x23, 0x26, 0x64 }, /* PIO mode 2 */
+        { 0x27, 0x0d, 0x35 }, /* PIO mode 3, IORDY on, Prefetch off */
+        { 0x23, 0x09, 0x25 }, /* PIO mode 4, IORDY on, Prefetch off */
+};
+
+static struct pdc2027x_mdma_timing {
+        u8 value0, value1;
+} pdc2027x_mdma_timing_tbl [] = {
+        { 0xdf, 0x5f }, /* MDMA mode 0 */
+        { 0x6b, 0x27 }, /* MDMA mode 1 */
+        { 0x69, 0x25 }, /* MDMA mode 2 */
+};
+
+static struct pdc2027x_udma_timing {
+        u8 value0, value1, value2;
+} pdc2027x_udma_timing_tbl [] = {
+        { 0x4a, 0x0f, 0xd5 }, /* UDMA mode 0 */
+        { 0x3a, 0x0a, 0xd0 }, /* UDMA mode 1 */
+        { 0x2a, 0x07, 0xcd }, /* UDMA mode 2 */
+        { 0x1a, 0x05, 0xcd }, /* UDMA mode 3 */
+        { 0x1a, 0x03, 0xcd }, /* UDMA mode 4 */
+        { 0x1a, 0x02, 0xcb }, /* UDMA mode 5 */
+        { 0x1a, 0x01, 0xcb }, /* UDMA mode 6 */
+};
+
+static const struct pci_device_id pdc2027x_pci_tbl[] = {
+        { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20268, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_100 },
+        { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20269, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 },
+        { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20270, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_100 },
+        { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20271, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 },
+        { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20275, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 },
+        { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20276, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 },
+        { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20277, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 },
+        { }     /* terminate list */
+};
+
+static struct pci_driver pdc2027x_pci_driver = {
+        .name                   = DRV_NAME,
+        .id_table               = pdc2027x_pci_tbl,
+        .probe                  = pdc2027x_init_one,
+        .remove                 = __devexit_p(pdc2027x_remove_one),
+};
+
+static struct scsi_host_template pdc2027x_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations pdc2027x_pata100_ops = {
+        .port_disable           = ata_port_disable,
+
+        .tf_load                = ata_tf_load,
+        .tf_read                = ata_tf_read,
+        .check_status           = ata_check_status,
+        .exec_command           = ata_exec_command,
+        .dev_select             = ata_std_dev_select,
+
+        .check_atapi_dma        = pdc2027x_check_atapi_dma,
+        .bmdma_setup            = ata_bmdma_setup,
+        .bmdma_start            = ata_bmdma_start,
+        .bmdma_stop             = ata_bmdma_stop,
+        .bmdma_status           = ata_bmdma_status,
+        .qc_prep                = ata_qc_prep,
+        .qc_issue               = ata_qc_issue_prot,
+        .data_xfer              = ata_mmio_data_xfer,
+
+        .freeze                 = ata_bmdma_freeze,
+        .thaw                   = ata_bmdma_thaw,
+        .error_handler          = pdc2027x_error_handler,
+        .post_internal_cmd      = ata_bmdma_post_internal_cmd,
+
+        .irq_handler            = ata_interrupt,
+        .irq_clear              = ata_bmdma_irq_clear,
+
+        .port_start             = ata_port_start,
+        .port_stop              = ata_port_stop,
+        .host_stop              = ata_pci_host_stop,
+};
+
+static struct ata_port_operations pdc2027x_pata133_ops = {
+        .port_disable           = ata_port_disable,
+        .set_piomode            = pdc2027x_set_piomode,
+        .set_dmamode            = pdc2027x_set_dmamode,
+        .post_set_mode          = pdc2027x_post_set_mode,
+
+        .tf_load                = ata_tf_load,
+        .tf_read                = ata_tf_read,
+        .check_status           = ata_check_status,
+        .exec_command           = ata_exec_command,
+        .dev_select             = ata_std_dev_select,
+
+        .check_atapi_dma        = pdc2027x_check_atapi_dma,
+        .bmdma_setup            = ata_bmdma_setup,
+        .bmdma_start            = ata_bmdma_start,
+        .bmdma_stop             = ata_bmdma_stop,
+        .bmdma_status           = ata_bmdma_status,
+        .qc_prep                = ata_qc_prep,
+        .qc_issue               = ata_qc_issue_prot,
+        .data_xfer              = ata_mmio_data_xfer,
+
+        .freeze                 = ata_bmdma_freeze,
+        .thaw                   = ata_bmdma_thaw,
+        .error_handler          = pdc2027x_error_handler,
+        .post_internal_cmd      = ata_bmdma_post_internal_cmd,
+
+        .irq_handler            = ata_interrupt,
+        .irq_clear              = ata_bmdma_irq_clear,
+
+        .port_start             = ata_port_start,
+        .port_stop              = ata_port_stop,
+        .host_stop              = ata_pci_host_stop,
+};
+
+static struct ata_port_info pdc2027x_port_info[] = {
+        /* PDC_UDMA_100 */
+        {
+                .sht            = &pdc2027x_sht,
+                .flags          = ATA_FLAG_NO_LEGACY | ATA_FLAG_SLAVE_POSS |
+                                  ATA_FLAG_MMIO,
+                .pio_mask       = 0x1f, /* pio0-4 */
+                .mwdma_mask     = 0x07, /* mwdma0-2 */
+                .udma_mask      = ATA_UDMA5, /* udma0-5 */
+                .port_ops       = &pdc2027x_pata100_ops,
+        },
+        /* PDC_UDMA_133 */
+        {
+                .sht            = &pdc2027x_sht,
+                .flags          = ATA_FLAG_NO_LEGACY | ATA_FLAG_SLAVE_POSS |
+                                  ATA_FLAG_MMIO,
+                .pio_mask       = 0x1f, /* pio0-4 */
+                .mwdma_mask     = 0x07, /* mwdma0-2 */
+                .udma_mask      = ATA_UDMA6, /* udma0-6 */
+                .port_ops       = &pdc2027x_pata133_ops,
+        },
+};
+
+MODULE_AUTHOR("Andre Hedrick, Frank Tiernan, Albert Lee");
+MODULE_DESCRIPTION("libata driver module for Promise PDC20268 to PDC20277");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
+MODULE_DEVICE_TABLE(pci, pdc2027x_pci_tbl);
+
+/**
+ *      port_mmio - Get the MMIO address of PDC2027x extended registers
+ *      @ap: Port
+ *      @offset: offset from mmio base
+ */
+static inline void* port_mmio(struct ata_port *ap, unsigned int offset)
+{
+        return ap->host->mmio_base + ap->port_no * 0x100 + offset;
+}
+
+/**
+ *      dev_mmio - Get the MMIO address of PDC2027x extended registers
+ *      @ap: Port
+ *      @adev: device
+ *      @offset: offset from mmio base
+ */
+static inline void* dev_mmio(struct ata_port *ap, struct ata_device *adev, unsigned int offset)
+{
+        u8 adj = (adev->devno) ? 0x08 : 0x00;
+        return port_mmio(ap, offset) + adj;
+}
+
+/**
+ *      pdc2027x_pata_cbl_detect - Probe host controller cable detect info
+ *      @ap: Port for which cable detect info is desired
+ *
+ *      Read 80c cable indicator from Promise extended register.
+ *      This register is latched when the system is reset.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+static void pdc2027x_cbl_detect(struct ata_port *ap)
+{
+        u32 cgcr;
+
+        /* check cable detect results */
+        cgcr = readl(port_mmio(ap, PDC_GLOBAL_CTL));
+        if (cgcr & (1 << 26))
+                goto cbl40;
+
+        PDPRINTK("No cable or 80-conductor cable on port %d\n", ap->port_no);
+
+        ap->cbl = ATA_CBL_PATA80;
+        return;
+
+cbl40:
+        printk(KERN_INFO DRV_NAME ": 40-conductor cable detected on port %d\n", ap->port_no);
+        ap->cbl = ATA_CBL_PATA40;
+        ap->udma_mask &= ATA_UDMA_MASK_40C;
+}
+
+/**
+ * pdc2027x_port_enabled - Check PDC ATA control register to see whether the port is enabled.
+ * @ap: Port to check
+ */
+static inline int pdc2027x_port_enabled(struct ata_port *ap)
+{
+        return readb(port_mmio(ap, PDC_ATA_CTL)) & 0x02;
+}
+
+/**
+ *      pdc2027x_prereset - prereset for PATA host controller
+ *      @ap: Target port
+ *
+ *      Probeinit including cable detection.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static int pdc2027x_prereset(struct ata_port *ap)
+{
+        /* Check whether port enabled */
+        if (!pdc2027x_port_enabled(ap)) {
+                printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+                return 0;
+        }
+        pdc2027x_cbl_detect(ap);
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      pdc2027x_error_handler - Perform reset on PATA port and classify
+ *      @ap: Port to reset
+ *
+ *      Reset PATA phy and classify attached devices.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void pdc2027x_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, pdc2027x_prereset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      pdc2027x_set_piomode - Initialize host controller PATA PIO timings
+ *      @ap: Port to configure
+ *      @adev: um
+ *      @pio: PIO mode, 0 - 4
+ *
+ *      Set PIO mode for device.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void pdc2027x_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        unsigned int pio = adev->pio_mode - XFER_PIO_0;
+        u32 ctcr0, ctcr1;
+
+        PDPRINTK("adev->pio_mode[%X]\n", adev->pio_mode);
+
+        /* Sanity check */
+        if (pio > 4) {
+                printk(KERN_ERR DRV_NAME ": Unknown pio mode [%d] ignored\n", pio);
+                return;
+
+        }
+
+        /* Set the PIO timing registers using value table for 133MHz */
+        PDPRINTK("Set pio regs... \n");
+
+        ctcr0 = readl(dev_mmio(ap, adev, PDC_CTCR0));
+        ctcr0 &= 0xffff0000;
+        ctcr0 |= pdc2027x_pio_timing_tbl[pio].value0 |
+                (pdc2027x_pio_timing_tbl[pio].value1 << 8);
+        writel(ctcr0, dev_mmio(ap, adev, PDC_CTCR0));
+
+        ctcr1 = readl(dev_mmio(ap, adev, PDC_CTCR1));
+        ctcr1 &= 0x00ffffff;
+        ctcr1 |= (pdc2027x_pio_timing_tbl[pio].value2 << 24);
+        writel(ctcr1, dev_mmio(ap, adev, PDC_CTCR1));
+
+        PDPRINTK("Set pio regs done\n");
+
+        PDPRINTK("Set to pio mode[%u] \n", pio);
+}
+
+/**
+ *      pdc2027x_set_dmamode - Initialize host controller PATA UDMA timings
+ *      @ap: Port to configure
+ *      @adev: um
+ *      @udma: udma mode, XFER_UDMA_0 to XFER_UDMA_6
+ *
+ *      Set UDMA mode for device.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+static void pdc2027x_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        unsigned int dma_mode = adev->dma_mode;
+        u32 ctcr0, ctcr1;
+
+        if ((dma_mode >= XFER_UDMA_0) &&
+           (dma_mode <= XFER_UDMA_6)) {
+                /* Set the UDMA timing registers with value table for 133MHz */
+                unsigned int udma_mode = dma_mode & 0x07;
+
+                if (dma_mode == XFER_UDMA_2) {
+                        /*
+                         * Turn off tHOLD.
+                         * If tHOLD is '1', the hardware will add half clock for data hold time.
+                         * This code segment seems to be no effect. tHOLD will be overwritten below.
+                         */
+                        ctcr1 = readl(dev_mmio(ap, adev, PDC_CTCR1));
+                        writel(ctcr1 & ~(1 << 7), dev_mmio(ap, adev, PDC_CTCR1));
+                }
+
+                PDPRINTK("Set udma regs... \n");
+
+                ctcr1 = readl(dev_mmio(ap, adev, PDC_CTCR1));
+                ctcr1 &= 0xff000000;
+                ctcr1 |= pdc2027x_udma_timing_tbl[udma_mode].value0 |
+                        (pdc2027x_udma_timing_tbl[udma_mode].value1 << 8) |
+                        (pdc2027x_udma_timing_tbl[udma_mode].value2 << 16);
+                writel(ctcr1, dev_mmio(ap, adev, PDC_CTCR1));
+
+                PDPRINTK("Set udma regs done\n");
+
+                PDPRINTK("Set to udma mode[%u] \n", udma_mode);
+
+        } else  if ((dma_mode >= XFER_MW_DMA_0) &&
+                   (dma_mode <= XFER_MW_DMA_2)) {
+                /* Set the MDMA timing registers with value table for 133MHz */
+                unsigned int mdma_mode = dma_mode & 0x07;
+
+                PDPRINTK("Set mdma regs... \n");
+                ctcr0 = readl(dev_mmio(ap, adev, PDC_CTCR0));
+
+                ctcr0 &= 0x0000ffff;
+                ctcr0 |= (pdc2027x_mdma_timing_tbl[mdma_mode].value0 << 16) |
+                        (pdc2027x_mdma_timing_tbl[mdma_mode].value1 << 24);
+
+                writel(ctcr0, dev_mmio(ap, adev, PDC_CTCR0));
+                PDPRINTK("Set mdma regs done\n");
+
+                PDPRINTK("Set to mdma mode[%u] \n", mdma_mode);
+        } else {
+                printk(KERN_ERR DRV_NAME ": Unknown dma mode [%u] ignored\n", dma_mode);
+        }
+}
+
+/**
+ *      pdc2027x_post_set_mode - Set the timing registers back to correct values.
+ *      @ap: Port to configure
+ *
+ *      The pdc2027x hardware will look at "SET FEATURES" and change the timing registers
+ *      automatically. The values set by the hardware might be incorrect, under 133Mhz PLL.
+ *      This function overwrites the possibly incorrect values set by the hardware to be correct.
+ */
+static void pdc2027x_post_set_mode(struct ata_port *ap)
+{
+        int i;
+
+        for (i = 0; i < ATA_MAX_DEVICES; i++) {
+                struct ata_device *dev = &ap->device[i];
+
+                if (ata_dev_enabled(dev)) {
+
+                        pdc2027x_set_piomode(ap, dev);
+
+                        /*
+                         * Enable prefetch if the device support PIO only.
+                         */
+                        if (dev->xfer_shift == ATA_SHIFT_PIO) {
+                                u32 ctcr1 = readl(dev_mmio(ap, dev, PDC_CTCR1));
+                                ctcr1 |= (1 << 25);
+                                writel(ctcr1, dev_mmio(ap, dev, PDC_CTCR1));
+
+                                PDPRINTK("Turn on prefetch\n");
+                        } else {
+                                pdc2027x_set_dmamode(ap, dev);
+                        }
+                }
+        }
+}
+
+/**
+ *      pdc2027x_check_atapi_dma - Check whether ATAPI DMA can be supported for this command
+ *      @qc: Metadata associated with taskfile to check
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ *
+ *      RETURNS: 0 when ATAPI DMA can be used
+ *               1 otherwise
+ */
+static int pdc2027x_check_atapi_dma(struct ata_queued_cmd *qc)
+{
+        struct scsi_cmnd *cmd = qc->scsicmd;
+        u8 *scsicmd = cmd->cmnd;
+        int rc = 1; /* atapi dma off by default */
+
+        /*
+         * This workaround is from Promise's GPL driver.
+         * If ATAPI DMA is used for commands not in the
+         * following white list, say MODE_SENSE and REQUEST_SENSE,
+         * pdc2027x might hit the irq lost problem.
+         */
+        switch (scsicmd[0]) {
+        case READ_10:
+        case WRITE_10:
+        case READ_12:
+        case WRITE_12:
+        case READ_6:
+        case WRITE_6:
+        case 0xad: /* READ_DVD_STRUCTURE */
+        case 0xbe: /* READ_CD */
+                /* ATAPI DMA is ok */
+                rc = 0;
+                break;
+        default:
+                ;
+        }
+
+        return rc;
+}
+
+/**
+ * pdc_read_counter - Read the ctr counter
+ * @probe_ent: for the port address
+ */
+
+static long pdc_read_counter(struct ata_probe_ent *probe_ent)
+{
+        long counter;
+        int retry = 1;
+        u32 bccrl, bccrh, bccrlv, bccrhv;
+
+retry:
+        bccrl = readl(probe_ent->mmio_base + PDC_BYTE_COUNT) & 0xffff;
+        bccrh = readl(probe_ent->mmio_base + PDC_BYTE_COUNT + 0x100) & 0xffff;
+        rmb();
+
+        /* Read the counter values again for verification */
+        bccrlv = readl(probe_ent->mmio_base + PDC_BYTE_COUNT) & 0xffff;
+        bccrhv = readl(probe_ent->mmio_base + PDC_BYTE_COUNT + 0x100) & 0xffff;
+        rmb();
+
+        counter = (bccrh << 15) | bccrl;
+
+        PDPRINTK("bccrh [%X] bccrl [%X]\n", bccrh,  bccrl);
+        PDPRINTK("bccrhv[%X] bccrlv[%X]\n", bccrhv, bccrlv);
+
+        /*
+         * The 30-bit decreasing counter are read by 2 pieces.
+         * Incorrect value may be read when both bccrh and bccrl are changing.
+         * Ex. When 7900 decrease to 78FF, wrong value 7800 might be read.
+         */
+        if (retry && !(bccrh == bccrhv && bccrl >= bccrlv)) {
+                retry--;
+                PDPRINTK("rereading counter\n");
+                goto retry;
+        }
+
+        return counter;
+}
+
+/**
+ * adjust_pll - Adjust the PLL input clock in Hz.
+ *
+ * @pdc_controller: controller specific information
+ * @probe_ent: For the port address
+ * @pll_clock: The input of PLL in HZ
+ */
+static void pdc_adjust_pll(struct ata_probe_ent *probe_ent, long pll_clock, unsigned int board_idx)
+{
+
+        u16 pll_ctl;
+        long pll_clock_khz = pll_clock / 1000;
+        long pout_required = board_idx? PDC_133_MHZ:PDC_100_MHZ;
+        long ratio = pout_required / pll_clock_khz;
+        int F, R;
+
+        /* Sanity check */
+        if (unlikely(pll_clock_khz < 5000L || pll_clock_khz > 70000L)) {
+                printk(KERN_ERR DRV_NAME ": Invalid PLL input clock %ldkHz, give up!\n", pll_clock_khz);
+                return;
+        }
+
+#ifdef PDC_DEBUG
+        PDPRINTK("pout_required is %ld\n", pout_required);
+
+        /* Show the current clock value of PLL control register
+         * (maybe already configured by the firmware)
+         */
+        pll_ctl = readw(probe_ent->mmio_base + PDC_PLL_CTL);
+
+        PDPRINTK("pll_ctl[%X]\n", pll_ctl);
+#endif
+
+        /*
+         * Calculate the ratio of F, R and OD
+         * POUT = (F + 2) / (( R + 2) * NO)
+         */
+        if (ratio < 8600L) { /* 8.6x */
+                /* Using NO = 0x01, R = 0x0D */
+                R = 0x0d;
+        } else if (ratio < 12900L) { /* 12.9x */
+                /* Using NO = 0x01, R = 0x08 */
+                R = 0x08;
+        } else if (ratio < 16100L) { /* 16.1x */
+                /* Using NO = 0x01, R = 0x06 */
+                R = 0x06;
+        } else if (ratio < 64000L) { /* 64x */
+                R = 0x00;
+        } else {
+                /* Invalid ratio */
+                printk(KERN_ERR DRV_NAME ": Invalid ratio %ld, give up!\n", ratio);
+                return;
+        }
+
+        F = (ratio * (R+2)) / 1000 - 2;
+
+        if (unlikely(F < 0 || F > 127)) {
+                /* Invalid F */
+                printk(KERN_ERR DRV_NAME ": F[%d] invalid!\n", F);
+                return;
+        }
+
+        PDPRINTK("F[%d] R[%d] ratio*1000[%ld]\n", F, R, ratio);
+
+        pll_ctl = (R << 8) | F;
+
+        PDPRINTK("Writing pll_ctl[%X]\n", pll_ctl);
+
+        writew(pll_ctl, probe_ent->mmio_base + PDC_PLL_CTL);
+        readw(probe_ent->mmio_base + PDC_PLL_CTL); /* flush */
+
+        /* Wait the PLL circuit to be stable */
+        mdelay(30);
+
+#ifdef PDC_DEBUG
+        /*
+         *  Show the current clock value of PLL control register
+         * (maybe configured by the firmware)
+         */
+        pll_ctl = readw(probe_ent->mmio_base + PDC_PLL_CTL);
+
+        PDPRINTK("pll_ctl[%X]\n", pll_ctl);
+#endif
+
+        return;
+}
+
+/**
+ * detect_pll_input_clock - Detect the PLL input clock in Hz.
+ * @probe_ent: for the port address
+ * Ex. 16949000 on 33MHz PCI bus for pdc20275.
+ *     Half of the PCI clock.
+ */
+static long pdc_detect_pll_input_clock(struct ata_probe_ent *probe_ent)
+{
+        u32 scr;
+        long start_count, end_count;
+        long pll_clock;
+
+        /* Read current counter value */
+        start_count = pdc_read_counter(probe_ent);
+
+        /* Start the test mode */
+        scr = readl(probe_ent->mmio_base + PDC_SYS_CTL);
+        PDPRINTK("scr[%X]\n", scr);
+        writel(scr | (0x01 << 14), probe_ent->mmio_base + PDC_SYS_CTL);
+        readl(probe_ent->mmio_base + PDC_SYS_CTL); /* flush */
+
+        /* Let the counter run for 100 ms. */
+        mdelay(100);
+
+        /* Read the counter values again */
+        end_count = pdc_read_counter(probe_ent);
+
+        /* Stop the test mode */
+        scr = readl(probe_ent->mmio_base + PDC_SYS_CTL);
+        PDPRINTK("scr[%X]\n", scr);
+        writel(scr & ~(0x01 << 14), probe_ent->mmio_base + PDC_SYS_CTL);
+        readl(probe_ent->mmio_base + PDC_SYS_CTL); /* flush */
+
+        /* calculate the input clock in Hz */
+        pll_clock = (start_count - end_count) * 10;
+
+        PDPRINTK("start[%ld] end[%ld] \n", start_count, end_count);
+        PDPRINTK("PLL input clock[%ld]Hz\n", pll_clock);
+
+        return pll_clock;
+}
+
+/**
+ * pdc_hardware_init - Initialize the hardware.
+ * @pdev: instance of pci_dev found
+ * @pdc_controller: controller specific information
+ * @pe:  for the port address
+ */
+static int pdc_hardware_init(struct pci_dev *pdev, struct ata_probe_ent *pe, unsigned int board_idx)
+{
+        long pll_clock;
+
+        /*
+         * Detect PLL input clock rate.
+         * On some system, where PCI bus is running at non-standard clock rate.
+         * Ex. 25MHz or 40MHz, we have to adjust the cycle_time.
+         * The pdc20275 controller employs PLL circuit to help correct timing registers setting.
+         */
+        pll_clock = pdc_detect_pll_input_clock(pe);
+
+        if (pll_clock < 0) /* counter overflow? Try again. */
+                pll_clock = pdc_detect_pll_input_clock(pe);
+
+        dev_printk(KERN_INFO, &pdev->dev, "PLL input clock %ld kHz\n", pll_clock/1000);
+
+        /* Adjust PLL control register */
+        pdc_adjust_pll(pe, pll_clock, board_idx);
+
+        return 0;
+}
+
+/**
+ * pdc_ata_setup_port - setup the mmio address
+ * @port: ata ioports to setup
+ * @base: base address
+ */
+static void pdc_ata_setup_port(struct ata_ioports *port, unsigned long base)
+{
+        port->cmd_addr          =
+        port->data_addr         = base;
+        port->feature_addr      =
+        port->error_addr        = base + 0x05;
+        port->nsect_addr        = base + 0x0a;
+        port->lbal_addr         = base + 0x0f;
+        port->lbam_addr         = base + 0x10;
+        port->lbah_addr         = base + 0x15;
+        port->device_addr       = base + 0x1a;
+        port->command_addr      =
+        port->status_addr       = base + 0x1f;
+        port->altstatus_addr    =
+        port->ctl_addr          = base + 0x81a;
+}
+
+/**
+ * pdc2027x_init_one - PCI probe function
+ * Called when an instance of PCI adapter is inserted.
+ * This function checks whether the hardware is supported,
+ * initialize hardware and register an instance of ata_host to
+ * libata by providing struct ata_probe_ent and ata_device_add().
+ * (implements struct pci_driver.probe() )
+ *
+ * @pdev: instance of pci_dev found
+ * @ent:  matching entry in the id_tbl[]
+ */
+static int __devinit pdc2027x_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+        static int printed_version;
+        unsigned int board_idx = (unsigned int) ent->driver_data;
+
+        struct ata_probe_ent *probe_ent = NULL;
+        unsigned long base;
+        void *mmio_base;
+        int rc;
+
+        if (!printed_version++)
+                dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
+
+        rc = pci_enable_device(pdev);
+        if (rc)
+                return rc;
+
+        rc = pci_request_regions(pdev, DRV_NAME);
+        if (rc)
+                goto err_out;
+
+        rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+        if (rc)
+                goto err_out_regions;
+
+        rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+        if (rc)
+                goto err_out_regions;
+
+        /* Prepare the probe entry */
+        probe_ent = kzalloc(sizeof(*probe_ent), GFP_KERNEL);
+        if (probe_ent == NULL) {
+                rc = -ENOMEM;
+                goto err_out_regions;
+        }
+
+        probe_ent->dev = pci_dev_to_dev(pdev);
+        INIT_LIST_HEAD(&probe_ent->node);
+
+        mmio_base = pci_iomap(pdev, 5, 0);
+        if (!mmio_base) {
+                rc = -ENOMEM;
+                goto err_out_free_ent;
+        }
+
+        base = (unsigned long) mmio_base;
+
+        probe_ent->sht          = pdc2027x_port_info[board_idx].sht;
+        probe_ent->port_flags   = pdc2027x_port_info[board_idx].flags;
+        probe_ent->pio_mask     = pdc2027x_port_info[board_idx].pio_mask;
+        probe_ent->mwdma_mask   = pdc2027x_port_info[board_idx].mwdma_mask;
+        probe_ent->udma_mask    = pdc2027x_port_info[board_idx].udma_mask;
+        probe_ent->port_ops     = pdc2027x_port_info[board_idx].port_ops;
+
+        probe_ent->irq = pdev->irq;
+        probe_ent->irq_flags = SA_SHIRQ;
+        probe_ent->mmio_base = mmio_base;
+
+        pdc_ata_setup_port(&probe_ent->port[0], base + 0x17c0);
+        probe_ent->port[0].bmdma_addr = base + 0x1000;
+        pdc_ata_setup_port(&probe_ent->port[1], base + 0x15c0);
+        probe_ent->port[1].bmdma_addr = base + 0x1008;
+
+        probe_ent->n_ports = 2;
+
+        pci_set_master(pdev);
+        //pci_enable_intx(pdev);
+
+        /* initialize adapter */
+        if (pdc_hardware_init(pdev, probe_ent, board_idx) != 0)
+                goto err_out_free_ent;
+
+        ata_device_add(probe_ent);
+        kfree(probe_ent);
+
+        return 0;
+
+err_out_free_ent:
+        kfree(probe_ent);
+err_out_regions:
+        pci_release_regions(pdev);
+err_out:
+        pci_disable_device(pdev);
+        return rc;
+}
+
+/**
+ * pdc2027x_remove_one - Called to remove a single instance of the
+ * adapter.
+ *
+ * @dev: The PCI device to remove.
+ * FIXME: module load/unload not working yet
+ */
+static void __devexit pdc2027x_remove_one(struct pci_dev *pdev)
+{
+        ata_pci_remove_one(pdev);
+}
+
+/**
+ * pdc2027x_init - Called after this module is loaded into the kernel.
+ */
+static int __init pdc2027x_init(void)
+{
+        return pci_module_init(&pdc2027x_pci_driver);
+}
+
+/**
+ * pdc2027x_exit - Called before this module unloaded from the kernel
+ */
+static void __exit pdc2027x_exit(void)
+{
+        pci_unregister_driver(&pdc2027x_pci_driver);
+}
+
+module_init(pdc2027x_init);
+module_exit(pdc2027x_exit);
diff --git a/drivers/ata/pata_pdc202xx_old.c b/drivers/ata/pata_pdc202xx_old.c
new file mode 100644
index 000000000000..48f43432764e
--- /dev/null
+++ b/drivers/ata/pata_pdc202xx_old.c
@@ -0,0 +1,423 @@
+/*
+ * pata_pdc202xx_old.c  - Promise PDC202xx PATA for new ATA layer
+ *                        (C) 2005 Red Hat Inc
+ *                        Alan Cox <alan@redhat.com>
+ *
+ * Based in part on linux/drivers/ide/pci/pdc202xx_old.c
+ *
+ * First cut with LBA48/ATAPI
+ *
+ * TODO:
+ *      Channel interlock/reset on both required ?
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_pdc202xx_old"
+#define DRV_VERSION "0.2.1"
+
+/**
+ *      pdc2024x_pre_reset              -       probe begin
+ *      @ap: ATA port
+ *
+ *      Set up cable type and use generic probe init
+ */
+
+static int pdc2024x_pre_reset(struct ata_port *ap)
+{
+        ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+}
+
+
+static void pdc2024x_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, pdc2024x_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+
+static int pdc2026x_pre_reset(struct ata_port *ap)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u16 cis;
+
+        pci_read_config_word(pdev, 0x50, &cis);
+        if (cis & (1 << (10 + ap->port_no)))
+                ap->cbl = ATA_CBL_PATA80;
+        else
+                ap->cbl = ATA_CBL_PATA40;
+
+        return ata_std_prereset(ap);
+}
+
+static void pdc2026x_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, pdc2026x_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      pdc_configure_piomode   -       set chip PIO timing
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *      @pio: PIO mode
+ *
+ *      Called to do the PIO mode setup. Our timing registers are shared
+ *      so a configure_dmamode call will undo any work we do here and vice
+ *      versa
+ */
+
+static void pdc_configure_piomode(struct ata_port *ap, struct ata_device *adev, int pio)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        int port = 0x60 + 4 * ap->port_no + 2 * adev->devno;
+        static u16 pio_timing[5] = {
+                0x0913, 0x050C , 0x0308, 0x0206, 0x0104
+        };
+        u8 r_ap, r_bp;
+
+        pci_read_config_byte(pdev, port, &r_ap);
+        pci_read_config_byte(pdev, port + 1, &r_bp);
+        r_ap &= ~0x3F;  /* Preserve ERRDY_EN, SYNC_IN */
+        r_bp &= ~0x07;
+        r_ap |= (pio_timing[pio] >> 8);
+        r_bp |= (pio_timing[pio] & 0xFF);
+
+        if (ata_pio_need_iordy(adev))
+                r_ap |= 0x20;   /* IORDY enable */
+        if (adev->class == ATA_DEV_ATA)
+                r_ap |= 0x10;   /* FIFO enable */
+        pci_write_config_byte(pdev, port, r_ap);
+        pci_write_config_byte(pdev, port + 1, r_bp);
+}
+
+/**
+ *      pdc_set_piomode -       set initial PIO mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Called to do the PIO mode setup. Our timing registers are shared
+ *      but we want to set the PIO timing by default.
+ */
+
+static void pdc_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        pdc_configure_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
+}
+
+/**
+ *      pdc_configure_dmamode   -       set DMA mode in chip
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Load DMA cycle times into the chip ready for a DMA transfer
+ *      to occur.
+ */
+
+static void pdc_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        int port = 0x60 + 4 * ap->port_no + 2 * adev->devno;
+        static u8 udma_timing[6][2] = {
+                { 0x60, 0x03 }, /* 33 Mhz Clock */
+                { 0x40, 0x02 },
+                { 0x20, 0x01 },
+                { 0x40, 0x02 }, /* 66 Mhz Clock */
+                { 0x20, 0x01 },
+                { 0x20, 0x01 }
+        };
+        u8 r_bp, r_cp;
+
+        pci_read_config_byte(pdev, port + 1, &r_bp);
+        pci_read_config_byte(pdev, port + 2, &r_cp);
+
+        r_bp &= ~0xF0;
+        r_cp &= ~0x0F;
+
+        if (adev->dma_mode >= XFER_UDMA_0) {
+                int speed = adev->dma_mode - XFER_UDMA_0;
+                r_bp |= udma_timing[speed][0];
+                r_cp |= udma_timing[speed][1];
+
+        } else {
+                int speed = adev->dma_mode - XFER_MW_DMA_0;
+                r_bp |= 0x60;
+                r_cp |= (5 - speed);
+        }
+        pci_write_config_byte(pdev, port + 1, r_bp);
+        pci_write_config_byte(pdev, port + 2, r_cp);
+
+}
+
+/**
+ *      pdc2026x_bmdma_start            -       DMA engine begin
+ *      @qc: ATA command
+ *
+ *      In UDMA3 or higher we have to clock switch for the duration of the
+ *      DMA transfer sequence.
+ */
+
+static void pdc2026x_bmdma_start(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct ata_device *adev = qc->dev;
+        struct ata_taskfile *tf = &qc->tf;
+        int sel66 = ap->port_no ? 0x08: 0x02;
+
+        unsigned long master = ap->host->ports[0]->ioaddr.bmdma_addr;
+        unsigned long clock = master + 0x11;
+        unsigned long atapi_reg = master + 0x20 + (4 * ap->port_no);
+
+        u32 len;
+
+        /* Check we keep host level locking here */
+        if (adev->dma_mode >= XFER_UDMA_2)
+                outb(inb(clock) | sel66, clock);
+        else
+                outb(inb(clock) & ~sel66, clock);
+
+        /* The DMA clocks may have been trashed by a reset. FIXME: make conditional
+           and move to qc_issue ? */
+        pdc_set_dmamode(ap, qc->dev);
+
+        /* Cases the state machine will not complete correctly without help */
+        if ((tf->flags & ATA_TFLAG_LBA48) ||  tf->protocol == ATA_PROT_ATAPI_DMA)
+        {
+                if (tf->flags & ATA_TFLAG_LBA48)
+                        len = qc->nsect * 512;
+                else
+                        len = qc->nbytes;
+
+                if (tf->flags & ATA_TFLAG_WRITE)
+                        len |= 0x06000000;
+                else
+                        len |= 0x05000000;
+
+                outl(len, atapi_reg);
+        }
+
+        /* Activate DMA */
+        ata_bmdma_start(qc);
+}
+
+/**
+ *      pdc2026x_bmdma_end              -       DMA engine stop
+ *      @qc: ATA command
+ *
+ *      After a DMA completes we need to put the clock back to 33MHz for
+ *      PIO timings.
+ */
+
+static void pdc2026x_bmdma_stop(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct ata_device *adev = qc->dev;
+        struct ata_taskfile *tf = &qc->tf;
+
+        int sel66 = ap->port_no ? 0x08: 0x02;
+        /* The clock bits are in the same register for both channels */
+        unsigned long master = ap->host->ports[0]->ioaddr.bmdma_addr;
+        unsigned long clock = master + 0x11;
+        unsigned long atapi_reg = master + 0x20 + (4 * ap->port_no);
+
+        /* Cases the state machine will not complete correctly */
+        if (tf->protocol == ATA_PROT_ATAPI_DMA || ( tf->flags & ATA_TFLAG_LBA48)) {
+                outl(0, atapi_reg);
+                outb(inb(clock) & ~sel66, clock);
+        }
+        /* Check we keep host level locking here */
+        /* Flip back to 33Mhz for PIO */
+        if (adev->dma_mode >= XFER_UDMA_2)
+                outb(inb(clock) & ~sel66, clock);
+
+        ata_bmdma_stop(qc);
+}
+
+/**
+ *      pdc2026x_dev_config     -       device setup hook
+ *      @ap: ATA port
+ *      @adev: newly found device
+ *
+ *      Perform chip specific early setup. We need to lock the transfer
+ *      sizes to 8bit to avoid making the state engine on the 2026x cards
+ *      barf.
+ */
+
+static void pdc2026x_dev_config(struct ata_port *ap, struct ata_device *adev)
+{
+        adev->max_sectors = 256;
+}
+
+static struct scsi_host_template pdc_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations pdc2024x_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = pdc_set_piomode,
+        .set_dmamode    = pdc_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = pdc2024x_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static struct ata_port_operations pdc2026x_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = pdc_set_piomode,
+        .set_dmamode    = pdc_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+        .dev_config     = pdc2026x_dev_config,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = pdc2026x_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = pdc2026x_bmdma_start,
+        .bmdma_stop     = pdc2026x_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static int pdc_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+        static struct ata_port_info info[3] = {
+                {
+                        .sht = &pdc_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .udma_mask = ATA_UDMA2,
+                        .port_ops = &pdc2024x_port_ops
+                },
+                {
+                        .sht = &pdc_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .udma_mask = ATA_UDMA4,
+                        .port_ops = &pdc2026x_port_ops
+                },
+                {
+                        .sht = &pdc_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .udma_mask = ATA_UDMA5,
+                        .port_ops = &pdc2026x_port_ops
+                }
+
+        };
+        static struct ata_port_info *port_info[2];
+
+        port_info[0] = port_info[1] = &info[id->driver_data];
+
+        if (dev->device == PCI_DEVICE_ID_PROMISE_20265) {
+                struct pci_dev *bridge = dev->bus->self;
+                /* Don't grab anything behind a Promise I2O RAID */
+                if (bridge && bridge->vendor == PCI_VENDOR_ID_INTEL) {
+                        if( bridge->device == PCI_DEVICE_ID_INTEL_I960)
+                                return -ENODEV;
+                        if( bridge->device == PCI_DEVICE_ID_INTEL_I960RM)
+                                return -ENODEV;
+                }
+        }
+        return ata_pci_init_one(dev, port_info, 2);
+}
+
+static struct pci_device_id pdc[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20246), 0},
+        { PCI_DEVICE(PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20262), 1},
+        { PCI_DEVICE(PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20263), 1},
+        { PCI_DEVICE(PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20265), 2},
+        { PCI_DEVICE(PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20267), 2},
+        { 0, },
+};
+
+static struct pci_driver pdc_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = pdc,
+        .probe          = pdc_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init pdc_init(void)
+{
+        return pci_register_driver(&pdc_pci_driver);
+}
+
+
+static void __exit pdc_exit(void)
+{
+        pci_unregister_driver(&pdc_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for Promise 2024x and 20262-20267");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, pdc);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(pdc_init);
+module_exit(pdc_exit);
diff --git a/drivers/ata/pata_qdi.c b/drivers/ata/pata_qdi.c
new file mode 100644
index 000000000000..35cfdf0ac3f0
--- /dev/null
+++ b/drivers/ata/pata_qdi.c
@@ -0,0 +1,403 @@
+/*
+ *    pata_qdi.c - QDI VLB ATA controllers
+ *      (C) 2006 Red Hat <alan@redhat.com>
+ *
+ * This driver mostly exists as a proof of concept for non PCI devices under
+ * libata. While the QDI6580 was 'neat' in 1993 it is no longer terribly
+ * useful.
+ *
+ * Tuning code written from the documentation at
+ * http://www.ryston.cz/petr/vlb/qd6500.html
+ * http://www.ryston.cz/petr/vlb/qd6580.html
+ *
+ * Probe code based on drivers/ide/legacy/qd65xx.c
+ * Rewritten from the work of Colten Edwards <pje120@cs.usask.ca> by
+ * Samuel Thibault <samuel.thibault@fnac.net>
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/platform_device.h>
+
+#define DRV_NAME "pata_qdi"
+#define DRV_VERSION "0.2.4"
+
+#define NR_HOST 4       /* Two 6580s */
+
+struct qdi_data {
+        unsigned long timing;
+        u8 clock[2];
+        u8 last;
+        int fast;
+        struct platform_device *platform_dev;
+
+};
+
+static struct ata_host *qdi_host[NR_HOST];
+static struct qdi_data qdi_data[NR_HOST];
+static int nr_qdi_host;
+
+#ifdef MODULE
+static int probe_qdi = 1;
+#else
+static int probe_qdi;
+#endif
+
+static void qdi6500_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct ata_timing t;
+        struct qdi_data *qdi = ap->host->private_data;
+        int active, recovery;
+        u8 timing;
+
+        /* Get the timing data in cycles */
+        ata_timing_compute(adev, adev->pio_mode, &t, 30303, 1000);
+
+        if (qdi->fast) {
+                active = 8 - FIT(t.active, 1, 8);
+                recovery = 18 - FIT(t.recover, 3, 18);
+        } else {
+                active = 9 - FIT(t.active, 2, 9);
+                recovery = 15 - FIT(t.recover, 0, 15);
+        }
+        timing = (recovery << 4) | active | 0x08;
+
+        qdi->clock[adev->devno] = timing;
+
+        outb(timing, qdi->timing);
+}
+
+static void qdi6580_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct ata_timing t;
+        struct qdi_data *qdi = ap->host->private_data;
+        int active, recovery;
+        u8 timing;
+
+        /* Get the timing data in cycles */
+        ata_timing_compute(adev, adev->pio_mode, &t, 30303, 1000);
+
+        if (qdi->fast) {
+                active = 8 - FIT(t.active, 1, 8);
+                recovery = 18 - FIT(t.recover, 3, 18);
+        } else {
+                active = 9 - FIT(t.active, 2, 9);
+                recovery = 15 - FIT(t.recover, 0, 15);
+        }
+        timing = (recovery << 4) | active | 0x08;
+
+        qdi->clock[adev->devno] = timing;
+
+        outb(timing, qdi->timing);
+
+        /* Clear the FIFO */
+        if (adev->class != ATA_DEV_ATA)
+                outb(0x5F, (qdi->timing & 0xFFF0) + 3);
+}
+
+/**
+ *      qdi_qc_issue_prot       -       command issue
+ *      @qc: command pending
+ *
+ *      Called when the libata layer is about to issue a command. We wrap
+ *      this interface so that we can load the correct ATA timings.
+ */
+
+static unsigned int qdi_qc_issue_prot(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct ata_device *adev = qc->dev;
+        struct qdi_data *qdi = ap->host->private_data;
+
+        if (qdi->clock[adev->devno] != qdi->last) {
+                if (adev->pio_mode) {
+                        qdi->last = qdi->clock[adev->devno];
+                        outb(qdi->clock[adev->devno], qdi->timing);
+                }
+        }
+        return ata_qc_issue_prot(qc);
+}
+
+static void qdi_data_xfer(struct ata_device *adev, unsigned char *buf, unsigned int buflen, int write_data)
+{
+        struct ata_port *ap = adev->ap;
+        int slop = buflen & 3;
+
+        if (ata_id_has_dword_io(adev->id)) {
+                if (write_data)
+                        outsl(ap->ioaddr.data_addr, buf, buflen >> 2);
+                else
+                        insl(ap->ioaddr.data_addr, buf, buflen >> 2);
+
+                if (unlikely(slop)) {
+                        u32 pad;
+                        if (write_data) {
+                                memcpy(&pad, buf + buflen - slop, slop);
+                                outl(le32_to_cpu(pad), ap->ioaddr.data_addr);
+                        } else {
+                                pad = cpu_to_le16(inl(ap->ioaddr.data_addr));
+                                memcpy(buf + buflen - slop, &pad, slop);
+                        }
+                }
+        } else
+                ata_pio_data_xfer(adev, buf, buflen, write_data);
+}
+
+static struct scsi_host_template qdi_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations qdi6500_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = qdi6500_set_piomode,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = ata_bmdma_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = qdi_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = qdi_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static struct ata_port_operations qdi6580_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = qdi6580_set_piomode,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = ata_bmdma_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = qdi_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = qdi_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/**
+ *      qdi_init_one            -       attach a qdi interface
+ *      @type: Type to display
+ *      @io: I/O port start
+ *      @irq: interrupt line
+ *      @fast: True if on a > 33Mhz VLB
+ *
+ *      Register an ISA bus IDE interface. Such interfaces are PIO and we
+ *      assume do not support IRQ sharing.
+ */
+
+static __init int qdi_init_one(unsigned long port, int type, unsigned long io, int irq, int fast)
+{
+        struct ata_probe_ent ae;
+        struct platform_device *pdev;
+        int ret;
+
+        unsigned long ctrl = io + 0x206;
+
+        /*
+         *      Fill in a probe structure first of all
+         */
+
+        pdev = platform_device_register_simple(DRV_NAME, nr_qdi_host, NULL, 0);
+        if (pdev == NULL)
+                return -ENOMEM;
+
+        memset(&ae, 0, sizeof(struct ata_probe_ent));
+        INIT_LIST_HEAD(&ae.node);
+        ae.dev = &pdev->dev;
+
+        if (type == 6580) {
+                ae.port_ops = &qdi6580_port_ops;
+                ae.pio_mask = 0x1F;
+        } else {
+                ae.port_ops = &qdi6500_port_ops;
+                ae.pio_mask = 0x07;     /* Actually PIO3 !IORDY is possible */
+        }
+
+        ae.sht = &qdi_sht;
+        ae.n_ports = 1;
+        ae.irq = irq;
+        ae.irq_flags = 0;
+        ae.port_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST;
+        ae.port[0].cmd_addr = io;
+        ae.port[0].altstatus_addr = ctrl;
+        ae.port[0].ctl_addr =   ctrl;
+        ata_std_ports(&ae.port[0]);
+
+        /*
+         *      Hook in a private data structure per channel
+         */
+        ae.private_data = &qdi_data[nr_qdi_host];
+
+        qdi_data[nr_qdi_host].timing = port;
+        qdi_data[nr_qdi_host].fast = fast;
+        qdi_data[nr_qdi_host].platform_dev = pdev;
+
+        printk(KERN_INFO DRV_NAME": qd%d at 0x%lx.\n", type, io);
+        ret = ata_device_add(&ae);
+        if (ret == 0) {
+                platform_device_unregister(pdev);
+                return -ENODEV;
+        }
+
+        qdi_host[nr_qdi_host++] = dev_get_drvdata(&pdev->dev);
+        return 0;
+}
+
+/**
+ *      qdi_init                -       attach qdi interfaces
+ *
+ *      Attach qdi IDE interfaces by scanning the ports it may occupy.
+ */
+
+static __init int qdi_init(void)
+{
+        unsigned long flags;
+        static const unsigned long qd_port[2] = { 0x30, 0xB0 };
+        static const unsigned long ide_port[2] = { 0x170, 0x1F0 };
+        static const int ide_irq[2] = { 14, 15 };
+
+        int ct = 0;
+        int i;
+
+        if (probe_qdi == 0)
+                return -ENODEV;
+
+        /*
+         *      Check each possible QD65xx base address
+         */
+
+        for (i = 0; i < 2; i++) {
+                unsigned long port = qd_port[i];
+                u8 r, res;
+
+
+                if (request_region(port, 2, "pata_qdi")) {
+                        /* Check for a card */
+                        local_irq_save(flags);
+                        r = inb_p(port);
+                        outb_p(0x19, port);
+                        res = inb_p(port);
+                        outb_p(r, port);
+                        local_irq_restore(flags);
+
+                        /* Fail */
+                        if (res == 0x19)
+                        {
+                                release_region(port, 2);
+                                continue;
+                        }
+
+                        /* Passes the presence test */
+                        r = inb_p(port + 1);    /* Check port agrees with port set */
+                        if ((r & 2) >> 1 != i) {
+                                release_region(port, 2);
+                                continue;
+                        }
+
+                        /* Check card type */
+                        if ((r & 0xF0) == 0xC0) {
+                                /* QD6500: single channel */
+                                if (r & 8) {
+                                        /* Disabled ? */
+                                        release_region(port, 2);
+                                        continue;
+                                }
+                                ct += qdi_init_one(port, 6500, ide_port[r & 0x01], ide_irq[r & 0x01], r & 0x04);
+                        }
+                        if (((r & 0xF0) == 0xA0) || (r & 0xF0) == 0x50) {
+                                /* QD6580: dual channel */
+                                if (!request_region(port + 2 , 2, "pata_qdi"))
+                                {
+                                        release_region(port, 2);
+                                        continue;
+                                }
+                                res = inb(port + 3);
+                                if (res & 1) {
+                                        /* Single channel mode */
+                                        ct += qdi_init_one(port, 6580, ide_port[r & 0x01], ide_irq[r & 0x01], r & 0x04);
+                                } else {
+                                        /* Dual channel mode */
+                                        ct += qdi_init_one(port, 6580, 0x1F0, 14, r & 0x04);
+                                        ct += qdi_init_one(port + 2, 6580, 0x170, 15, r & 0x04);
+                                }
+                        }
+                }
+        }
+        if (ct != 0)
+                return 0;
+        return -ENODEV;
+}
+
+static __exit void qdi_exit(void)
+{
+        int i;
+
+        for (i = 0; i < nr_qdi_host; i++) {
+                ata_host_remove(qdi_host[i]);
+                /* Free the control resource. The 6580 dual channel has the resources
+                 * claimed as a pair of 2 byte resources so we need no special cases...
+                 */
+                release_region(qdi_data[i].timing, 2);
+                platform_device_unregister(qdi_data[i].platform_dev);
+        }
+}
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for qdi ATA");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
+
+module_init(qdi_init);
+module_exit(qdi_exit);
+
+module_param(probe_qdi, int, 0);
+
diff --git a/drivers/ata/pata_radisys.c b/drivers/ata/pata_radisys.c
new file mode 100644
index 000000000000..277f8411b521
--- /dev/null
+++ b/drivers/ata/pata_radisys.c
@@ -0,0 +1,335 @@
+/*
+ *    pata_radisys.c - Intel PATA/SATA controllers
+ *
+ *      (C) 2006 Red Hat <alan@redhat.com>
+ *
+ *    Some parts based on ata_piix.c by Jeff Garzik and others.
+ *
+ *    A PIIX relative, this device has a single ATA channel and no
+ *    slave timings, SITRE or PPE. In that sense it is a close relative
+ *    of the original PIIX. It does however support UDMA 33/66 per channel
+ *    although no other modes/timings. Also lacking is 32bit I/O on the ATA
+ *    port.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/ata.h>
+
+#define DRV_NAME        "pata_radisys"
+#define DRV_VERSION     "0.4.1"
+
+/**
+ *      radisys_probe_init              -       probe begin
+ *      @ap: ATA port
+ *
+ *      Set up cable type and use generic probe init
+ */
+
+static int radisys_pre_reset(struct ata_port *ap)
+{
+        ap->cbl = ATA_CBL_PATA80;
+        return ata_std_prereset(ap);
+}
+
+
+/**
+ *      radisys_pata_error_handler - Probe specified port on PATA host controller
+ *      @ap: Port to probe
+ *      @classes:
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void radisys_pata_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, radisys_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      radisys_set_piomode - Initialize host controller PATA PIO timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: um
+ *
+ *      Set PIO mode for device, in host controller PCI config space.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void radisys_set_piomode (struct ata_port *ap, struct ata_device *adev)
+{
+        unsigned int pio        = adev->pio_mode - XFER_PIO_0;
+        struct pci_dev *dev     = to_pci_dev(ap->host->dev);
+        u16 idetm_data;
+        int control = 0;
+
+        /*
+         *      See Intel Document 298600-004 for the timing programing rules
+         *      for PIIX/ICH. Note that the early PIIX does not have the slave
+         *      timing port at 0x44. The Radisys is a relative of the PIIX
+         *      but not the same so be careful.
+         */
+
+        static const     /* ISP  RTC */
+        u8 timings[][2] = { { 0, 0 },   /* Check me */
+                            { 0, 0 },
+                            { 1, 1 },
+                            { 2, 2 },
+                            { 3, 3 }, };
+
+        if (pio > 0)
+                control |= 1;   /* TIME1 enable */
+        if (ata_pio_need_iordy(adev))
+                control |= 2;   /* IE IORDY */
+
+        pci_read_config_word(dev, 0x40, &idetm_data);
+
+        /* Enable IE and TIME as appropriate. Clear the other
+           drive timing bits */
+        idetm_data &= 0xCCCC;
+        idetm_data |= (control << (4 * adev->devno));
+        idetm_data |= (timings[pio][0] << 12) |
+                        (timings[pio][1] << 8);
+        pci_write_config_word(dev, 0x40, idetm_data);
+
+        /* Track which port is configured */
+        ap->private_data = adev;
+}
+
+/**
+ *      radisys_set_dmamode - Initialize host controller PATA DMA timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device to program
+ *      @isich: True if the device is an ICH and has IOCFG registers
+ *
+ *      Set MWDMA mode for device, in host controller PCI config space.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void radisys_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *dev     = to_pci_dev(ap->host->dev);
+        u16 idetm_data;
+        u8 udma_enable;
+
+        static const     /* ISP  RTC */
+        u8 timings[][2] = { { 0, 0 },
+                            { 0, 0 },
+                            { 1, 1 },
+                            { 2, 2 },
+                            { 3, 3 }, };
+
+        /*
+         * MWDMA is driven by the PIO timings. We must also enable
+         * IORDY unconditionally.
+         */
+
+        pci_read_config_word(dev, 0x40, &idetm_data);
+        pci_read_config_byte(dev, 0x48, &udma_enable);
+
+        if (adev->dma_mode < XFER_UDMA_0) {
+                unsigned int mwdma      = adev->dma_mode - XFER_MW_DMA_0;
+                const unsigned int needed_pio[3] = {
+                        XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
+                };
+                int pio = needed_pio[mwdma] - XFER_PIO_0;
+                int control = 3;        /* IORDY|TIME0 */
+
+                /* If the drive MWDMA is faster than it can do PIO then
+                   we must force PIO0 for PIO cycles. */
+
+                if (adev->pio_mode < needed_pio[mwdma])
+                        control = 1;
+
+                /* Mask out the relevant control and timing bits we will load. Also
+                   clear the other drive TIME register as a precaution */
+
+                idetm_data &= 0xCCCC;
+                idetm_data |= control << (4 * adev->devno);
+                idetm_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8);
+
+                udma_enable &= ~(1 << adev->devno);
+        } else {
+                u8 udma_mode;
+
+                /* UDMA66 on: UDMA 33 and 66 are switchable via register 0x4A */
+
+                pci_read_config_byte(dev, 0x4A, &udma_mode);
+
+                if (adev->xfer_mode == XFER_UDMA_2)
+                        udma_mode &= ~ (1 << adev->devno);
+                else /* UDMA 4 */
+                        udma_mode |= (1 << adev->devno);
+
+                pci_write_config_byte(dev, 0x4A, udma_mode);
+
+                udma_enable |= (1 << adev->devno);
+        }
+        pci_write_config_word(dev, 0x40, idetm_data);
+        pci_write_config_byte(dev, 0x48, udma_enable);
+
+        /* Track which port is configured */
+        ap->private_data = adev;
+}
+
+/**
+ *      radisys_qc_issue_prot   -       command issue
+ *      @qc: command pending
+ *
+ *      Called when the libata layer is about to issue a command. We wrap
+ *      this interface so that we can load the correct ATA timings if
+ *      neccessary. Our logic also clears TIME0/TIME1 for the other device so
+ *      that, even if we get this wrong, cycles to the other device will
+ *      be made PIO0.
+ */
+
+static unsigned int radisys_qc_issue_prot(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct ata_device *adev = qc->dev;
+
+        if (adev != ap->private_data) {
+                /* UDMA timing is not shared */
+                if (adev->dma_mode < XFER_UDMA_0) {
+                        if (adev->dma_mode)
+                                radisys_set_dmamode(ap, adev);
+                        else if (adev->pio_mode)
+                                radisys_set_piomode(ap, adev);
+                }
+        }
+        return ata_qc_issue_prot(qc);
+}
+
+
+static struct scsi_host_template radisys_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static const struct ata_port_operations radisys_pata_ops = {
+        .port_disable           = ata_port_disable,
+        .set_piomode            = radisys_set_piomode,
+        .set_dmamode            = radisys_set_dmamode,
+        .mode_filter            = ata_pci_default_filter,
+
+        .tf_load                = ata_tf_load,
+        .tf_read                = ata_tf_read,
+        .check_status           = ata_check_status,
+        .exec_command           = ata_exec_command,
+        .dev_select             = ata_std_dev_select,
+
+        .freeze                 = ata_bmdma_freeze,
+        .thaw                   = ata_bmdma_thaw,
+        .error_handler          = radisys_pata_error_handler,
+        .post_internal_cmd      = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup            = ata_bmdma_setup,
+        .bmdma_start            = ata_bmdma_start,
+        .bmdma_stop             = ata_bmdma_stop,
+        .bmdma_status           = ata_bmdma_status,
+        .qc_prep                = ata_qc_prep,
+        .qc_issue               = radisys_qc_issue_prot,
+        .data_xfer              = ata_pio_data_xfer,
+
+        .eng_timeout            = ata_eng_timeout,
+
+        .irq_handler            = ata_interrupt,
+        .irq_clear              = ata_bmdma_irq_clear,
+
+        .port_start             = ata_port_start,
+        .port_stop              = ata_port_stop,
+        .host_stop              = ata_host_stop,
+};
+
+
+/**
+ *      radisys_init_one - Register PIIX ATA PCI device with kernel services
+ *      @pdev: PCI device to register
+ *      @ent: Entry in radisys_pci_tbl matching with @pdev
+ *
+ *      Called from kernel PCI layer.  We probe for combined mode (sigh),
+ *      and then hand over control to libata, for it to do the rest.
+ *
+ *      LOCKING:
+ *      Inherited from PCI layer (may sleep).
+ *
+ *      RETURNS:
+ *      Zero on success, or -ERRNO value.
+ */
+
+static int radisys_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+        static int printed_version;
+        static struct ata_port_info info = {
+                .sht            = &radisys_sht,
+                .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask       = 0x1f, /* pio0-4 */
+                .mwdma_mask     = 0x07, /* mwdma1-2 */
+                .udma_mask      = 0x14, /* UDMA33/66 only */
+                .port_ops       = &radisys_pata_ops,
+        };
+        static struct ata_port_info *port_info[2] = { &info, &info };
+
+        if (!printed_version++)
+                dev_printk(KERN_DEBUG, &pdev->dev,
+                           "version " DRV_VERSION "\n");
+
+        return ata_pci_init_one(pdev, port_info, 2);
+}
+
+static const struct pci_device_id radisys_pci_tbl[] = {
+        { 0x1331, 0x8201, PCI_ANY_ID, PCI_ANY_ID, },
+        { }     /* terminate list */
+};
+
+static struct pci_driver radisys_pci_driver = {
+        .name                   = DRV_NAME,
+        .id_table               = radisys_pci_tbl,
+        .probe                  = radisys_init_one,
+        .remove                 = ata_pci_remove_one,
+};
+
+static int __init radisys_init(void)
+{
+        return pci_register_driver(&radisys_pci_driver);
+}
+
+static void __exit radisys_exit(void)
+{
+        pci_unregister_driver(&radisys_pci_driver);
+}
+
+
+module_init(radisys_init);
+module_exit(radisys_exit);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("SCSI low-level driver for Radisys R82600 controllers");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, radisys_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+
diff --git a/drivers/ata/pata_rz1000.c b/drivers/ata/pata_rz1000.c
new file mode 100644
index 000000000000..3c6d84fd4312
--- /dev/null
+++ b/drivers/ata/pata_rz1000.c
@@ -0,0 +1,205 @@
+/*
+ *  RZ1000/1001 driver based upon
+ *
+ *  linux/drivers/ide/pci/rz1000.c      Version 0.06    January 12, 2003
+ *  Copyright (C) 1995-1998  Linus Torvalds & author (see below)
+ *  Principal Author:  mlord@pobox.com (Mark Lord)
+ *
+ *  See linux/MAINTAINERS for address of current maintainer.
+ *
+ *  This file provides support for disabling the buggy read-ahead
+ *  mode of the RZ1000 IDE chipset, commonly used on Intel motherboards.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME        "pata_rz1000"
+#define DRV_VERSION     "0.2.2"
+
+
+/**
+ *      rz1000_prereset         -       probe begin
+ *      @ap: ATA port
+ *
+ *      Set up cable type and use generics
+ */
+
+static int rz1000_prereset(struct ata_port *ap)
+{
+        ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      rz1000_error_handler            -       probe reset
+ *      @ap: ATA port
+ *
+ *      Perform the ATA standard reset sequence
+ */
+
+static void rz1000_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, rz1000_prereset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      rz1000_set_mode         -       mode setting function
+ *      @ap: ATA interface
+ *
+ *      Use a non standard set_mode function. We don't want to be tuned. We
+ *      would prefer to be BIOS generic but for the fact our hardware is
+ *      whacked out.
+ */
+
+static void rz1000_set_mode(struct ata_port *ap)
+{
+        int i;
+
+        for (i = 0; i < ATA_MAX_DEVICES; i++) {
+                struct ata_device *dev = &ap->device[i];
+                if (ata_dev_enabled(dev)) {
+                        /* We don't really care */
+                        dev->pio_mode = XFER_PIO_0;
+                        dev->xfer_mode = XFER_PIO_0;
+                        dev->xfer_shift = ATA_SHIFT_PIO;
+                        dev->flags |= ATA_DFLAG_PIO;
+                }
+        }
+}
+
+
+static struct scsi_host_template rz1000_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations rz1000_port_ops = {
+        .set_mode       = rz1000_set_mode,
+
+        .port_disable   = ata_port_disable,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .error_handler  = rz1000_error_handler,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = rz1000_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/**
+ *      rz1000_init_one - Register RZ1000 ATA PCI device with kernel services
+ *      @pdev: PCI device to register
+ *      @ent: Entry in rz1000_pci_tbl matching with @pdev
+ *
+ *      Configure an RZ1000 interface. This doesn't require much special
+ *      handling except that we *MUST* kill the chipset readahead or the
+ *      user may experience data corruption.
+ */
+
+static int rz1000_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+        static int printed_version;
+        struct ata_port_info *port_info[2];
+        u16 reg;
+        static struct ata_port_info info = {
+                .sht = &rz1000_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .port_ops = &rz1000_port_ops
+        };
+
+        if (!printed_version++)
+                printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+
+        /* Be exceptionally paranoid as we must be sure to apply the fix */
+        if (pci_read_config_word(pdev, 0x40, &reg) != 0)
+                goto fail;
+        reg &= 0xDFFF;
+        if (pci_write_config_word(pdev, 0x40, reg) != 0)
+                goto fail;
+        printk(KERN_INFO DRV_NAME ": disabled chipset readahead.\n");
+
+        port_info[0] = &info;
+        port_info[1] = &info;
+        return ata_pci_init_one(pdev, port_info, 2);
+fail:
+        printk(KERN_ERR DRV_NAME ": failed to disable read-ahead on chipset..\n");
+        /* Not safe to use so skip */
+        return -ENODEV;
+}
+
+static struct pci_device_id pata_rz1000[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_PCTECH, PCI_DEVICE_ID_PCTECH_RZ1000), },
+        { PCI_DEVICE(PCI_VENDOR_ID_PCTECH, PCI_DEVICE_ID_PCTECH_RZ1001), },
+        { 0, },
+};
+
+static struct pci_driver rz1000_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = pata_rz1000,
+        .probe          = rz1000_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+
+static int __init rz1000_init(void)
+{
+        return pci_register_driver(&rz1000_pci_driver);
+}
+
+static void __exit rz1000_exit(void)
+{
+        pci_unregister_driver(&rz1000_pci_driver);
+}
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for RZ1000 PCI ATA");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, pata_rz1000);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(rz1000_init);
+module_exit(rz1000_exit);
+
diff --git a/drivers/ata/pata_sc1200.c b/drivers/ata/pata_sc1200.c
new file mode 100644
index 000000000000..4166c1a8a9e8
--- /dev/null
+++ b/drivers/ata/pata_sc1200.c
@@ -0,0 +1,287 @@
+/*
+ * New ATA layer SC1200 driver          Alan Cox <alan@redhat.com>
+ *
+ * TODO: Mode selection filtering
+ * TODO: Can't enable second channel until ATA core has serialize
+ * TODO: Needs custom DMA cleanup code
+ *
+ * Based very heavily on
+ *
+ * linux/drivers/ide/pci/sc1200.c               Version 0.91    28-Jan-2003
+ *
+ * Copyright (C) 2000-2002              Mark Lord <mlord@pobox.com>
+ * May be copied or modified under the terms of the GNU General Public License
+ *
+ * Development of this chipset driver was funded
+ * by the nice folks at National Semiconductor.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME        "sc1200"
+#define DRV_VERSION     "0.2.3"
+
+#define SC1200_REV_A    0x00
+#define SC1200_REV_B1   0x01
+#define SC1200_REV_B3   0x02
+#define SC1200_REV_C1   0x03
+#define SC1200_REV_D1   0x04
+
+/**
+ *      sc1200_clock    -       PCI clock
+ *
+ *      Return the PCI bus clocking for the SC1200 chipset configuration
+ *      in use. We return 0 for 33MHz 1 for 48MHz and 2 for 66Mhz
+ */
+
+static int sc1200_clock(void)
+{
+        /* Magic registers that give us the chipset data */
+        u8 chip_id = inb(0x903C);
+        u8 silicon_rev = inb(0x903D);
+        u16 pci_clock;
+
+        if (chip_id == 0x04 && silicon_rev < SC1200_REV_B1)
+                return 0;       /* 33 MHz mode */
+
+        /* Clock generator configuration 0x901E its 8/9 are the PCI clocking
+           0/3 is 33Mhz 1 is 48 2 is 66 */
+
+        pci_clock = inw(0x901E);
+        pci_clock >>= 8;
+        pci_clock &= 0x03;
+        if (pci_clock == 3)
+                pci_clock = 0;
+        return pci_clock;
+}
+
+/**
+ *      sc1200_set_piomode              -       PIO setup
+ *      @ap: ATA interface
+ *      @adev: device on the interface
+ *
+ *      Set our PIO requirements. This is fairly simple on the SC1200
+ */
+
+static void sc1200_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        static const u32 pio_timings[4][5] = {
+                {0x00009172, 0x00012171, 0x00020080, 0x00032010, 0x00040010},   // format0  33Mhz
+                {0xd1329172, 0x71212171, 0x30200080, 0x20102010, 0x00100010},   // format1, 33Mhz
+                {0xfaa3f4f3, 0xc23232b2, 0x513101c1, 0x31213121, 0x10211021},   // format1, 48Mhz
+                {0xfff4fff4, 0xf35353d3, 0x814102f1, 0x42314231, 0x11311131}    // format1, 66Mhz
+        };
+
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u32 format;
+        unsigned int reg = 0x40 + 0x10 * ap->port_no;
+        int mode = adev->pio_mode - XFER_PIO_0;
+
+        pci_read_config_dword(pdev, reg + 4, &format);
+        format >>= 31;
+        format += sc1200_clock();
+        pci_write_config_dword(pdev, reg + 8 * adev->devno,
+                                pio_timings[format][mode]);
+}
+
+/**
+ *      sc1200_set_dmamode              -       DMA timing setup
+ *      @ap: ATA interface
+ *      @adev: Device being configured
+ *
+ *      We cannot mix MWDMA and UDMA without reloading timings each switch
+ *      master to slave.
+ */
+
+static void sc1200_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        static const u32 udma_timing[3][3] = {
+                { 0x00921250, 0x00911140, 0x00911030 },
+                { 0x00932470, 0x00922260, 0x00922140 },
+                { 0x009436A1, 0x00933481, 0x00923261 }
+        };
+
+        static const u32 mwdma_timing[3][3] = {
+                { 0x00077771, 0x00012121, 0x00002020 },
+                { 0x000BBBB2, 0x00024241, 0x00013131 },
+                { 0x000FFFF3, 0x00035352, 0x00015151 }
+        };
+
+        int clock = sc1200_clock();
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        unsigned int reg = 0x40 + 0x10 * ap->port_no;
+        int mode = adev->dma_mode;
+        u32 format;
+
+        if (mode >= XFER_UDMA_0)
+                format = udma_timing[clock][mode - XFER_UDMA_0];
+        else
+                format = mwdma_timing[clock][mode - XFER_MW_DMA_0];
+
+        if (adev->devno == 0) {
+                u32 timings;
+
+                pci_read_config_dword(pdev, reg + 4, &timings);
+                timings &= 0x80000000UL;
+                timings |= format;
+                pci_write_config_dword(pdev, reg + 4, timings);
+        } else
+                pci_write_config_dword(pdev, reg + 12, format);
+}
+
+/**
+ *      sc1200_qc_issue_prot    -       command issue
+ *      @qc: command pending
+ *
+ *      Called when the libata layer is about to issue a command. We wrap
+ *      this interface so that we can load the correct ATA timings if
+ *      neccessary.  Specifically we have a problem that there is only
+ *      one MWDMA/UDMA bit.
+ */
+
+static unsigned int sc1200_qc_issue_prot(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct ata_device *adev = qc->dev;
+        struct ata_device *prev = ap->private_data;
+
+        /* See if the DMA settings could be wrong */
+        if (adev->dma_mode != 0 && adev != prev && prev != NULL) {
+                /* Maybe, but do the channels match MWDMA/UDMA ? */
+                if ((adev->dma_mode >= XFER_UDMA_0 && prev->dma_mode < XFER_UDMA_0) ||
+                    (adev->dma_mode < XFER_UDMA_0 && prev->dma_mode >= XFER_UDMA_0))
+                        /* Switch the mode bits */
+                        sc1200_set_dmamode(ap, adev);
+        }
+
+        return ata_qc_issue_prot(qc);
+}
+
+static struct scsi_host_template sc1200_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations sc1200_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = sc1200_set_piomode,
+        .set_dmamode    = sc1200_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .error_handler  = ata_bmdma_error_handler,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = sc1200_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/**
+ *      sc1200_init_one         -       Initialise an SC1200
+ *      @dev: PCI device
+ *      @id: Entry in match table
+ *
+ *      Just throw the needed data at the libata helper and it does all
+ *      our work.
+ */
+
+static int sc1200_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+        static struct ata_port_info info = {
+                .sht = &sc1200_sht,
+                .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x07,
+                .port_ops = &sc1200_port_ops
+        };
+        static struct ata_port_info *port_info[2] = { &info, &info };
+
+        /* Can't enable port 2 yet, see top comments */
+        return ata_pci_init_one(dev, port_info, 1);
+}
+
+static struct pci_device_id sc1200[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_SCx200_IDE), },
+        { 0, },
+};
+
+static struct pci_driver sc1200_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = sc1200,
+        .probe          = sc1200_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init sc1200_init(void)
+{
+        return pci_register_driver(&sc1200_pci_driver);
+}
+
+
+static void __exit sc1200_exit(void)
+{
+        pci_unregister_driver(&sc1200_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox, Mark Lord");
+MODULE_DESCRIPTION("low-level driver for the NS/AMD SC1200");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, sc1200);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(sc1200_init);
+module_exit(sc1200_exit);
diff --git a/drivers/ata/pata_serverworks.c b/drivers/ata/pata_serverworks.c
new file mode 100644
index 000000000000..af456113c55d
--- /dev/null
+++ b/drivers/ata/pata_serverworks.c
@@ -0,0 +1,587 @@
+/*
+ * ata-serverworks.c    - Serverworks PATA for new ATA layer
+ *                        (C) 2005 Red Hat Inc
+ *                        Alan Cox <alan@redhat.com>
+ *
+ * based upon
+ *
+ * serverworks.c
+ *
+ * Copyright (C) 1998-2000 Michel Aubry
+ * Copyright (C) 1998-2000 Andrzej Krzysztofowicz
+ * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
+ * Portions copyright (c) 2001 Sun Microsystems
+ *
+ *
+ * RCC/ServerWorks IDE driver for Linux
+ *
+ *   OSB4: `Open South Bridge' IDE Interface (fn 1)
+ *         supports UDMA mode 2 (33 MB/s)
+ *
+ *   CSB5: `Champion South Bridge' IDE Interface (fn 1)
+ *         all revisions support UDMA mode 4 (66 MB/s)
+ *         revision A2.0 and up support UDMA mode 5 (100 MB/s)
+ *
+ *         *** The CSB5 does not provide ANY register ***
+ *         *** to detect 80-conductor cable presence. ***
+ *
+ *   CSB6: `Champion South Bridge' IDE Interface (optional: third channel)
+ *
+ * Documentation:
+ *      Available under NDA only. Errata info very hard to get.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_serverworks"
+#define DRV_VERSION "0.3.6"
+
+#define SVWKS_CSB5_REVISION_NEW 0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
+#define SVWKS_CSB6_REVISION     0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */
+
+/* Seagate Barracuda ATA IV Family drives in UDMA mode 5
+ * can overrun their FIFOs when used with the CSB5 */
+
+static const char *csb_bad_ata100[] = {
+        "ST320011A",
+        "ST340016A",
+        "ST360021A",
+        "ST380021A",
+        NULL
+};
+
+/**
+ *      dell_cable      -       Dell serverworks cable detection
+ *      @ap: ATA port to do cable detect
+ *
+ *      Dell hide the 40/80 pin select for their interfaces in the top two
+ *      bits of the subsystem ID.
+ */
+
+static int dell_cable(struct ata_port *ap) {
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+        if (pdev->subsystem_device & (1 << (ap->port_no + 14)))
+                return ATA_CBL_PATA80;
+        return ATA_CBL_PATA40;
+}
+
+/**
+ *      sun_cable       -       Sun Cobalt 'Alpine' cable detection
+ *      @ap: ATA port to do cable select
+ *
+ *      Cobalt CSB5 IDE hides the 40/80pin in the top two bits of the
+ *      subsystem ID the same as dell. We could use one function but we may
+ *      need to extend the Dell one in future
+ */
+
+static int sun_cable(struct ata_port *ap) {
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+        if (pdev->subsystem_device & (1 << (ap->port_no + 14)))
+                return ATA_CBL_PATA80;
+        return ATA_CBL_PATA40;
+}
+
+/**
+ *      osb4_cable      -       OSB4 cable detect
+ *      @ap: ATA port to check
+ *
+ *      The OSB4 isn't UDMA66 capable so this is easy
+ */
+
+static int osb4_cable(struct ata_port *ap) {
+        return ATA_CBL_PATA40;
+}
+
+/**
+ *      csb4_cable      -       CSB5/6 cable detect
+ *      @ap: ATA port to check
+ *
+ *      Serverworks default arrangement is to use the drive side detection
+ *      only.
+ */
+
+static int csb_cable(struct ata_port *ap) {
+        return ATA_CBL_PATA80;
+}
+
+struct sv_cable_table {
+        int device;
+        int subvendor;
+        int (*cable_detect)(struct ata_port *ap);
+};
+
+/*
+ *      Note that we don't copy the old serverworks code because the old
+ *      code contains obvious mistakes
+ */
+
+static struct sv_cable_table cable_detect[] = {
+        { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_VENDOR_ID_DELL, dell_cable },
+        { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE, PCI_VENDOR_ID_DELL, dell_cable },
+        { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_VENDOR_ID_SUN,  sun_cable },
+        { PCI_DEVICE_ID_SERVERWORKS_OSB4, PCI_ANY_ID, osb4_cable },
+        { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_ANY_ID, csb_cable },
+        { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE, PCI_ANY_ID, csb_cable },
+        { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2, PCI_ANY_ID, csb_cable },
+        { PCI_DEVICE_ID_SERVERWORKS_HT1000IDE, PCI_ANY_ID, csb_cable },
+        { }
+};
+
+/**
+ *      serverworks_pre_reset           -       cable detection
+ *      @ap: ATA port
+ *
+ *      Perform cable detection according to the device and subvendor
+ *      identifications
+ */
+
+static int serverworks_pre_reset(struct ata_port *ap) {
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        struct sv_cable_table *cb = cable_detect;
+
+        while(cb->device) {
+                if (cb->device == pdev->device &&
+                    (cb->subvendor == pdev->subsystem_vendor ||
+                      cb->subvendor == PCI_ANY_ID)) {
+                        ap->cbl = cb->cable_detect(ap);
+                        return ata_std_prereset(ap);
+                }
+                cb++;
+        }
+
+        BUG();
+        return -1;      /* kill compiler warning */
+}
+
+static void serverworks_error_handler(struct ata_port *ap)
+{
+        return ata_bmdma_drive_eh(ap, serverworks_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      serverworks_is_csb      -       Check for CSB or OSB
+ *      @pdev: PCI device to check
+ *
+ *      Returns true if the device being checked is known to be a CSB
+ *      series device.
+ */
+
+static u8 serverworks_is_csb(struct pci_dev *pdev)
+{
+        switch (pdev->device) {
+                case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
+                case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
+                case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
+                case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
+                        return 1;
+                default:
+                        break;
+        }
+        return 0;
+}
+
+/**
+ *      serverworks_osb4_filter -       mode selection filter
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Filter the offered modes for the device to apply controller
+ *      specific rules. OSB4 requires no UDMA for disks due to a FIFO
+ *      bug we hit.
+ */
+
+static unsigned long serverworks_osb4_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask)
+{
+        if (adev->class == ATA_DEV_ATA)
+                mask &= ~ATA_MASK_UDMA;
+        return ata_pci_default_filter(ap, adev, mask);
+}
+
+
+/**
+ *      serverworks_csb_filter  -       mode selection filter
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Check the blacklist and disable UDMA5 if matched
+ */
+
+static unsigned long serverworks_csb_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask)
+{
+        const char *p;
+        char model_num[40];
+        int len, i;
+
+        /* Disk, UDMA */
+        if (adev->class != ATA_DEV_ATA)
+                return ata_pci_default_filter(ap, adev, mask);
+
+        /* Actually do need to check */
+        ata_id_string(adev->id, model_num, ATA_ID_PROD_OFS, sizeof(model_num));
+        /* Precuationary - why not do this in the libata core ?? */
+
+        len = strlen(model_num);
+        while ((len > 0) && (model_num[len - 1] == ' ')) {
+                len--;
+                model_num[len] = 0;
+        }
+
+        for(i = 0; (p = csb_bad_ata100[i]) != NULL; i++) {
+                if (!strncmp(p, model_num, len))
+                        mask &= ~(0x1F << ATA_SHIFT_UDMA);
+        }
+        return ata_pci_default_filter(ap, adev, mask);
+}
+
+
+/**
+ *      serverworks_set_piomode -       set initial PIO mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Program the OSB4/CSB5 timing registers for PIO. The PIO register
+ *      load is done as a simple lookup.
+ */
+static void serverworks_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        static const u8 pio_mode[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
+        int offset = 1 + (2 * ap->port_no) - adev->devno;
+        int devbits = (2 * ap->port_no + adev->devno) * 4;
+        u16 csb5_pio;
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        int pio = adev->pio_mode - XFER_PIO_0;
+
+        pci_write_config_byte(pdev, 0x40 + offset, pio_mode[pio]);
+
+        /* The OSB4 just requires the timing but the CSB series want the
+           mode number as well */
+        if (serverworks_is_csb(pdev)) {
+                pci_read_config_word(pdev, 0x4A, &csb5_pio);
+                csb5_pio &= ~(0x0F << devbits);
+                pci_write_config_byte(pdev, 0x4A, csb5_pio | (pio << devbits));
+        }
+}
+
+/**
+ *      serverworks_set_dmamode -       set initial DMA mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Program the MWDMA/UDMA modes for the serverworks OSB4/CSB5
+ *      chipset. The MWDMA mode values are pulled from a lookup table
+ *      while the chipset uses mode number for UDMA.
+ */
+
+static void serverworks_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        static const u8 dma_mode[] = { 0x77, 0x21, 0x20 };
+        int offset = 1 + 2 * ap->port_no - adev->devno;
+        int devbits = (2 * ap->port_no + adev->devno);
+        u8 ultra;
+        u8 ultra_cfg;
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+        pci_read_config_byte(pdev, 0x54, &ultra_cfg);
+
+        if (adev->dma_mode >= XFER_UDMA_0) {
+                pci_write_config_byte(pdev, 0x44 + offset,  0x20);
+
+                pci_read_config_byte(pdev, 0x56 + ap->port_no, &ultra);
+                ultra &= ~(0x0F << (ap->port_no * 4));
+                ultra |= (adev->dma_mode - XFER_UDMA_0)
+                                        << (ap->port_no * 4);
+                pci_write_config_byte(pdev, 0x56 + ap->port_no, ultra);
+
+                ultra_cfg |=  (1 << devbits);
+        } else {
+                pci_write_config_byte(pdev, 0x44 + offset,
+                        dma_mode[adev->dma_mode - XFER_MW_DMA_0]);
+                ultra_cfg &= ~(1 << devbits);
+        }
+        pci_write_config_byte(pdev, 0x54, ultra_cfg);
+}
+
+static struct scsi_host_template serverworks_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations serverworks_osb4_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = serverworks_set_piomode,
+        .set_dmamode    = serverworks_set_dmamode,
+        .mode_filter    = serverworks_osb4_filter,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = serverworks_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static struct ata_port_operations serverworks_csb_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = serverworks_set_piomode,
+        .set_dmamode    = serverworks_set_dmamode,
+        .mode_filter    = serverworks_csb_filter,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = serverworks_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static int serverworks_fixup_osb4(struct pci_dev *pdev)
+{
+        u32 reg;
+        struct pci_dev *isa_dev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
+                  PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL);
+        if (isa_dev) {
+                pci_read_config_dword(isa_dev, 0x64, &reg);
+                reg &= ~0x00002000; /* disable 600ns interrupt mask */
+                if (!(reg & 0x00004000))
+                        printk(KERN_DEBUG DRV_NAME ": UDMA not BIOS enabled.\n");
+                reg |=  0x00004000; /* enable UDMA/33 support */
+                pci_write_config_dword(isa_dev, 0x64, reg);
+                pci_dev_put(isa_dev);
+                return 0;
+        }
+        printk(KERN_WARNING "ata_serverworks: Unable to find bridge.\n");
+        return -ENODEV;
+}
+
+static int serverworks_fixup_csb(struct pci_dev *pdev)
+{
+        u8 rev;
+        u8 btr;
+
+        pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
+
+        /* Third Channel Test */
+        if (!(PCI_FUNC(pdev->devfn) & 1)) {
+                struct pci_dev * findev = NULL;
+                u32 reg4c = 0;
+                findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
+                        PCI_DEVICE_ID_SERVERWORKS_CSB5, NULL);
+                if (findev) {
+                        pci_read_config_dword(findev, 0x4C, &reg4c);
+                        reg4c &= ~0x000007FF;
+                        reg4c |=  0x00000040;
+                        reg4c |=  0x00000020;
+                        pci_write_config_dword(findev, 0x4C, reg4c);
+                        pci_dev_put(findev);
+                }
+        } else {
+                struct pci_dev * findev = NULL;
+                u8 reg41 = 0;
+
+                findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
+                                PCI_DEVICE_ID_SERVERWORKS_CSB6, NULL);
+                if (findev) {
+                        pci_read_config_byte(findev, 0x41, &reg41);
+                        reg41 &= ~0x40;
+                        pci_write_config_byte(findev, 0x41, reg41);
+                        pci_dev_put(findev);
+                }
+        }
+        /* setup the UDMA Control register
+         *
+         * 1. clear bit 6 to enable DMA
+         * 2. enable DMA modes with bits 0-1
+         *      00 : legacy
+         *      01 : udma2
+         *      10 : udma2/udma4
+         *      11 : udma2/udma4/udma5
+         */
+        pci_read_config_byte(pdev, 0x5A, &btr);
+        btr &= ~0x40;
+        if (!(PCI_FUNC(pdev->devfn) & 1))
+                btr |= 0x2;
+        else
+                btr |= (rev >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2;
+        pci_write_config_byte(pdev, 0x5A, btr);
+
+        return btr;
+}
+
+static void serverworks_fixup_ht1000(struct pci_dev *pdev)
+{
+        u8 btr;
+        /* Setup HT1000 SouthBridge Controller - Single Channel Only */
+        pci_read_config_byte(pdev, 0x5A, &btr);
+        btr &= ~0x40;
+        btr |= 0x3;
+        pci_write_config_byte(pdev, 0x5A, btr);
+}
+
+
+static int serverworks_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+        int ports = 2;
+        static struct ata_port_info info[4] = {
+                { /* OSB4 */
+                        .sht = &serverworks_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .udma_mask = 0x07,
+                        .port_ops = &serverworks_osb4_port_ops
+                }, { /* OSB4 no UDMA */
+                        .sht = &serverworks_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .udma_mask = 0x00,
+                        .port_ops = &serverworks_osb4_port_ops
+                }, { /* CSB5 */
+                        .sht = &serverworks_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .udma_mask = 0x1f,
+                        .port_ops = &serverworks_csb_port_ops
+                }, { /* CSB5 - later revisions*/
+                        .sht = &serverworks_sht,
+                        .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                        .pio_mask = 0x1f,
+                        .mwdma_mask = 0x07,
+                        .udma_mask = 0x3f,
+                        .port_ops = &serverworks_csb_port_ops
+                }
+        };
+        static struct ata_port_info *port_info[2];
+        struct ata_port_info *devinfo = &info[id->driver_data];
+
+        /* Force master latency timer to 64 PCI clocks */
+        pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x40);
+
+        /* OSB4 : South Bridge and IDE */
+        if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
+                /* Select non UDMA capable OSB4 if we can't do fixups */
+                if ( serverworks_fixup_osb4(pdev) < 0)
+                        devinfo = &info[1];
+        }
+        /* setup CSB5/CSB6 : South Bridge and IDE option RAID */
+        else if ((pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) ||
+                 (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
+                 (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) {
+
+                 /* If the returned btr is the newer revision then
+                    select the right info block */
+                 if (serverworks_fixup_csb(pdev) == 3)
+                        devinfo = &info[3];
+
+                /* Is this the 3rd channel CSB6 IDE ? */
+                if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)
+                        ports = 1;
+        }
+        /* setup HT1000E */
+        else if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE)
+                serverworks_fixup_ht1000(pdev);
+
+        if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE)
+                ata_pci_clear_simplex(pdev);
+
+        port_info[0] = port_info[1] = devinfo;
+        return ata_pci_init_one(pdev, port_info, ports);
+}
+
+static struct pci_device_id serverworks[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE), 0},
+        { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE), 2},
+        { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE), 2},
+        { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2), 2},
+        { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE), 2},
+        { 0, },
+};
+
+static struct pci_driver serverworks_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = serverworks,
+        .probe          = serverworks_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init serverworks_init(void)
+{
+        return pci_register_driver(&serverworks_pci_driver);
+}
+
+
+static void __exit serverworks_exit(void)
+{
+        pci_unregister_driver(&serverworks_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for Serverworks OSB4/CSB5/CSB6");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, serverworks);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(serverworks_init);
+module_exit(serverworks_exit);
diff --git a/drivers/ata/pata_sil680.c b/drivers/ata/pata_sil680.c
new file mode 100644
index 000000000000..8f7db9638d0a
--- /dev/null
+++ b/drivers/ata/pata_sil680.c
@@ -0,0 +1,381 @@
+/*
+ * pata_sil680.c        - SIL680 PATA for new ATA layer
+ *                        (C) 2005 Red Hat Inc
+ *                        Alan Cox <alan@redhat.com>
+ *
+ * based upon
+ *
+ * linux/drivers/ide/pci/siimage.c              Version 1.07    Nov 30, 2003
+ *
+ * Copyright (C) 2001-2002      Andre Hedrick <andre@linux-ide.org>
+ * Copyright (C) 2003           Red Hat <alan@redhat.com>
+ *
+ *  May be copied or modified under the terms of the GNU General Public License
+ *
+ *  Documentation publically available.
+ *
+ *      If you have strange problems with nVidia chipset systems please
+ *      see the SI support documentation and update your system BIOS
+ *      if neccessary
+ *
+ * TODO
+ *      If we know all our devices are LBA28 (or LBA28 sized)  we could use
+ *      the command fifo mode.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_sil680"
+#define DRV_VERSION "0.3.2"
+
+/**
+ *      sil680_selreg           -       return register base
+ *      @hwif: interface
+ *      @r: config offset
+ *
+ *      Turn a config register offset into the right address in either
+ *      PCI space or MMIO space to access the control register in question
+ *      Thankfully this is a configuration operation so isnt performance
+ *      criticial.
+ */
+
+static unsigned long sil680_selreg(struct ata_port *ap, int r)
+{
+        unsigned long base = 0xA0 + r;
+        base += (ap->port_no << 4);
+        return base;
+}
+
+/**
+ *      sil680_seldev           -       return register base
+ *      @hwif: interface
+ *      @r: config offset
+ *
+ *      Turn a config register offset into the right address in either
+ *      PCI space or MMIO space to access the control register in question
+ *      including accounting for the unit shift.
+ */
+
+static unsigned long sil680_seldev(struct ata_port *ap, struct ata_device *adev, int r)
+{
+        unsigned long base = 0xA0 + r;
+        base += (ap->port_no << 4);
+        base |= adev->devno ? 2 : 0;
+        return base;
+}
+
+
+/**
+ *      sil680_cable_detect     -       cable detection
+ *      @ap: ATA port
+ *
+ *      Perform cable detection. The SIL680 stores this in PCI config
+ *      space for us.
+ */
+
+static int sil680_cable_detect(struct ata_port *ap) {
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        unsigned long addr = sil680_selreg(ap, 0);
+        u8 ata66;
+        pci_read_config_byte(pdev, addr, &ata66);
+        if (ata66 & 1)
+                return ATA_CBL_PATA80;
+        else
+                return ATA_CBL_PATA40;
+}
+
+static int sil680_pre_reset(struct ata_port *ap)
+{
+        ap->cbl = sil680_cable_detect(ap);
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      sil680_bus_reset        -       reset the SIL680 bus
+ *      @ap: ATA port to reset
+ *
+ *      Perform the SIL680 housekeeping when doing an ATA bus reset
+ */
+
+static int sil680_bus_reset(struct ata_port *ap,unsigned int *classes)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        unsigned long addr = sil680_selreg(ap, 0);
+        u8 reset;
+
+        pci_read_config_byte(pdev, addr, &reset);
+        pci_write_config_byte(pdev, addr, reset | 0x03);
+        udelay(25);
+        pci_write_config_byte(pdev, addr, reset);
+        return ata_std_softreset(ap, classes);
+}
+
+static void sil680_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, sil680_pre_reset, sil680_bus_reset, NULL, ata_std_postreset);
+}
+
+/**
+ *      sil680_set_piomode      -       set initial PIO mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Program the SIL680 registers for PIO mode. Note that the task speed
+ *      registers are shared between the devices so we must pick the lowest
+ *      mode for command work.
+ */
+
+static void sil680_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        static u16 speed_p[5] = { 0x328A, 0x2283, 0x1104, 0x10C3, 0x10C1 };
+        static u16 speed_t[5] = { 0x328A, 0x1281, 0x1281, 0x10C3, 0x10C1 };
+
+        unsigned long tfaddr = sil680_selreg(ap, 0x02);
+        unsigned long addr = sil680_seldev(ap, adev, 0x04);
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        int pio = adev->pio_mode - XFER_PIO_0;
+        int lowest_pio = pio;
+        u16 reg;
+
+        struct ata_device *pair = ata_dev_pair(adev);
+
+        if (pair != NULL && adev->pio_mode > pair->pio_mode)
+                lowest_pio = pair->pio_mode - XFER_PIO_0;
+
+        pci_write_config_word(pdev, addr, speed_p[pio]);
+        pci_write_config_word(pdev, tfaddr, speed_t[lowest_pio]);
+
+        pci_read_config_word(pdev, tfaddr-2, &reg);
+        reg &= ~0x0200;                 /* Clear IORDY */
+        if (ata_pio_need_iordy(adev))
+                reg |= 0x0200;          /* Enable IORDY */
+        pci_write_config_word(pdev, tfaddr-2, reg);
+}
+
+/**
+ *      sil680_set_dmamode      -       set initial DMA mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Program the MWDMA/UDMA modes for the sil680 k
+ *      chipset. The MWDMA mode values are pulled from a lookup table
+ *      while the chipset uses mode number for UDMA.
+ */
+
+static void sil680_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        static u8 ultra_table[2][7] = {
+                { 0x0C, 0x07, 0x05, 0x04, 0x02, 0x01, 0xFF },   /* 100MHz */
+                { 0x0F, 0x0B, 0x07, 0x05, 0x03, 0x02, 0x01 },   /* 133Mhz */
+        };
+        static u16 dma_table[3] = { 0x2208, 0x10C2, 0x10C1 };
+
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        unsigned long ma = sil680_seldev(ap, adev, 0x08);
+        unsigned long ua = sil680_seldev(ap, adev, 0x0C);
+        unsigned long addr_mask = 0x80 + 4 * ap->port_no;
+        int port_shift = adev->devno * 4;
+        u8 scsc, mode;
+        u16 multi, ultra;
+
+        pci_read_config_byte(pdev, 0x8A, &scsc);
+        pci_read_config_byte(pdev, addr_mask, &mode);
+        pci_read_config_word(pdev, ma, &multi);
+        pci_read_config_word(pdev, ua, &ultra);
+
+        /* Mask timing bits */
+        ultra &= ~0x3F;
+        mode &= ~(0x03 << port_shift);
+
+        /* Extract scsc */
+        scsc = (scsc & 0x30) ? 1: 0;
+
+        if (adev->dma_mode >= XFER_UDMA_0) {
+                multi = 0x10C1;
+                ultra |= ultra_table[scsc][adev->dma_mode - XFER_UDMA_0];
+                mode |= (0x03 << port_shift);
+        } else {
+                multi = dma_table[adev->dma_mode - XFER_MW_DMA_0];
+                mode |= (0x02 << port_shift);
+        }
+        pci_write_config_byte(pdev, addr_mask, mode);
+        pci_write_config_word(pdev, ma, multi);
+        pci_write_config_word(pdev, ua, ultra);
+}
+
+static struct scsi_host_template sil680_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations sil680_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = sil680_set_piomode,
+        .set_dmamode    = sil680_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = sil680_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static int sil680_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+        static struct ata_port_info info = {
+                .sht = &sil680_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x7f,
+                .port_ops = &sil680_port_ops
+        };
+        static struct ata_port_info info_slow = {
+                .sht = &sil680_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x3f,
+                .port_ops = &sil680_port_ops
+        };
+        static struct ata_port_info *port_info[2] = {&info, &info};
+        static int printed_version;
+        u32 class_rev   = 0;
+        u8 tmpbyte      = 0;
+
+        if (!printed_version++)
+                dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
+
+        pci_read_config_dword(pdev, PCI_CLASS_REVISION, &class_rev);
+        class_rev &= 0xff;
+        /* FIXME: double check */
+        pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, (class_rev) ? 1 : 255);
+
+        pci_write_config_byte(pdev, 0x80, 0x00);
+        pci_write_config_byte(pdev, 0x84, 0x00);
+
+        pci_read_config_byte(pdev, 0x8A, &tmpbyte);
+
+        printk(KERN_INFO "sil680: BA5_EN = %d clock = %02X\n",
+                        tmpbyte & 1, tmpbyte & 0x30);
+
+        switch(tmpbyte & 0x30) {
+                case 0x00:
+                        /* 133 clock attempt to force it on */
+                        pci_write_config_byte(pdev, 0x8A, tmpbyte|0x10);
+                        break;
+                case 0x30:
+                        /* if clocking is disabled */
+                        /* 133 clock attempt to force it on */
+                        pci_write_config_byte(pdev, 0x8A, tmpbyte & ~0x20);
+                        break;
+                case 0x10:
+                        /* 133 already */
+                        break;
+                case 0x20:
+                        /* BIOS set PCI x2 clocking */
+                        break;
+        }
+
+        pci_read_config_byte(pdev,   0x8A, &tmpbyte);
+        printk(KERN_INFO "sil680: BA5_EN = %d clock = %02X\n",
+                        tmpbyte & 1, tmpbyte & 0x30);
+        if ((tmpbyte & 0x30) == 0)
+                port_info[0] = port_info[1] = &info_slow;
+
+        pci_write_config_byte(pdev,  0xA1, 0x72);
+        pci_write_config_word(pdev,  0xA2, 0x328A);
+        pci_write_config_dword(pdev, 0xA4, 0x62DD62DD);
+        pci_write_config_dword(pdev, 0xA8, 0x43924392);
+        pci_write_config_dword(pdev, 0xAC, 0x40094009);
+        pci_write_config_byte(pdev,  0xB1, 0x72);
+        pci_write_config_word(pdev,  0xB2, 0x328A);
+        pci_write_config_dword(pdev, 0xB4, 0x62DD62DD);
+        pci_write_config_dword(pdev, 0xB8, 0x43924392);
+        pci_write_config_dword(pdev, 0xBC, 0x40094009);
+
+        switch(tmpbyte & 0x30) {
+                case 0x00: printk(KERN_INFO "sil680: 100MHz clock.\n");break;
+                case 0x10: printk(KERN_INFO "sil680: 133MHz clock.\n");break;
+                case 0x20: printk(KERN_INFO "sil680: Using PCI clock.\n");break;
+                /* This last case is _NOT_ ok */
+                case 0x30: printk(KERN_ERR "sil680: Clock disabled ?\n");
+                        return -EIO;
+        }
+        return ata_pci_init_one(pdev, port_info, 2);
+}
+
+static const struct pci_device_id sil680[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_SII_680), },
+        { 0, },
+};
+
+static struct pci_driver sil680_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = sil680,
+        .probe          = sil680_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init sil680_init(void)
+{
+        return pci_register_driver(&sil680_pci_driver);
+}
+
+
+static void __exit sil680_exit(void)
+{
+        pci_unregister_driver(&sil680_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for SI680 PATA");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, sil680);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(sil680_init);
+module_exit(sil680_exit);
diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c
new file mode 100644
index 000000000000..1cf5cf0a5365
--- /dev/null
+++ b/drivers/ata/pata_sis.c
@@ -0,0 +1,1030 @@
+/*
+ *    pata_sis.c - SiS ATA driver
+ *
+ *      (C) 2005 Red Hat <alan@redhat.com>
+ *
+ *    Based upon linux/drivers/ide/pci/sis5513.c
+ * Copyright (C) 1999-2000      Andre Hedrick <andre@linux-ide.org>
+ * Copyright (C) 2002           Lionel Bouton <Lionel.Bouton@inet6.fr>, Maintainer
+ * Copyright (C) 2003           Vojtech Pavlik <vojtech@suse.cz>
+ * SiS Taiwan           : for direct support and hardware.
+ * Daniela Engert       : for initial ATA100 advices and numerous others.
+ * John Fremlin, Manfred Spraul, Dave Morgan, Peter Kjellerstedt        :
+ *                        for checking code correctness, providing patches.
+ * Original tests and design on the SiS620 chipset.
+ * ATA100 tests and design on the SiS735 chipset.
+ * ATA16/33 support from specs
+ * ATA133 support for SiS961/962 by L.C. Chang <lcchang@sis.com.tw>
+ *
+ *
+ *      TODO
+ *      Check MWDMA on drives that don't support MWDMA speed pio cycles ?
+ *      More Testing
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/ata.h>
+
+#define DRV_NAME        "pata_sis"
+#define DRV_VERSION     "0.4.2"
+
+struct sis_chipset {
+        u16 device;                     /* PCI host ID */
+        struct ata_port_info *info;     /* Info block */
+        /* Probably add family, cable detect type etc here to clean
+           up code later */
+};
+
+/**
+ *      sis_port_base           -       return PCI configuration base for dev
+ *      @adev: device
+ *
+ *      Returns the base of the PCI configuration registers for this port
+ *      number.
+ */
+
+static int sis_port_base(struct ata_device *adev)
+{
+        return  0x40 + (4 * adev->ap->port_no) +  (2 * adev->devno);
+}
+
+/**
+ *      sis_133_pre_reset       -       check for 40/80 pin
+ *      @ap: Port
+ *
+ *      Perform cable detection for the later UDMA133 capable
+ *      SiS chipset.
+ */
+
+static int sis_133_pre_reset(struct ata_port *ap)
+{
+        static const struct pci_bits sis_enable_bits[] = {
+                { 0x4aU, 1U, 0x02UL, 0x02UL },  /* port 0 */
+                { 0x4aU, 1U, 0x04UL, 0x04UL },  /* port 1 */
+        };
+
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u16 tmp;
+
+        if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no])) {
+                ata_port_disable(ap);
+                printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+                return 0;
+        }
+        /* The top bit of this register is the cable detect bit */
+        pci_read_config_word(pdev, 0x50 + 2 * ap->port_no, &tmp);
+        if (tmp & 0x8000)
+                ap->cbl = ATA_CBL_PATA40;
+        else
+                ap->cbl = ATA_CBL_PATA80;
+
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      sis_error_handler - Probe specified port on PATA host controller
+ *      @ap: Port to probe
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void sis_133_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, sis_133_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+
+/**
+ *      sis_66_pre_reset        -       check for 40/80 pin
+ *      @ap: Port
+ *
+ *      Perform cable detection on the UDMA66, UDMA100 and early UDMA133
+ *      SiS IDE controllers.
+ */
+
+static int sis_66_pre_reset(struct ata_port *ap)
+{
+        static const struct pci_bits sis_enable_bits[] = {
+                { 0x4aU, 1U, 0x02UL, 0x02UL },  /* port 0 */
+                { 0x4aU, 1U, 0x04UL, 0x04UL },  /* port 1 */
+        };
+
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u8 tmp;
+
+        if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no])) {
+                ata_port_disable(ap);
+                printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+                return 0;
+        }
+        /* Older chips keep cable detect in bits 4/5 of reg 0x48 */
+        pci_read_config_byte(pdev, 0x48, &tmp);
+        tmp >>= ap->port_no;
+        if (tmp & 0x10)
+                ap->cbl = ATA_CBL_PATA40;
+        else
+                ap->cbl = ATA_CBL_PATA80;
+
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      sis_66_error_handler - Probe specified port on PATA host controller
+ *      @ap: Port to probe
+ *      @classes:
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void sis_66_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, sis_66_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      sis_old_pre_reset               -       probe begin
+ *      @ap: ATA port
+ *
+ *      Set up cable type and use generic probe init
+ */
+
+static int sis_old_pre_reset(struct ata_port *ap)
+{
+        static const struct pci_bits sis_enable_bits[] = {
+                { 0x4aU, 1U, 0x02UL, 0x02UL },  /* port 0 */
+                { 0x4aU, 1U, 0x04UL, 0x04UL },  /* port 1 */
+        };
+
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+        if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no])) {
+                ata_port_disable(ap);
+                printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+                return 0;
+        }
+        ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+}
+
+
+/**
+ *      sis_old_error_handler - Probe specified port on PATA host controller
+ *      @ap: Port to probe
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void sis_old_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, sis_old_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      sis_set_fifo    -       Set RWP fifo bits for this device
+ *      @ap: Port
+ *      @adev: Device
+ *
+ *      SIS chipsets implement prefetch/postwrite bits for each device
+ *      on both channels. This functionality is not ATAPI compatible and
+ *      must be configured according to the class of device present
+ */
+
+static void sis_set_fifo(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u8 fifoctrl;
+        u8 mask = 0x11;
+
+        mask <<= (2 * ap->port_no);
+        mask <<= adev->devno;
+
+        /* This holds various bits including the FIFO control */
+        pci_read_config_byte(pdev, 0x4B, &fifoctrl);
+        fifoctrl &= ~mask;
+
+        /* Enable for ATA (disk) only */
+        if (adev->class == ATA_DEV_ATA)
+                fifoctrl |= mask;
+        pci_write_config_byte(pdev, 0x4B, fifoctrl);
+}
+
+/**
+ *      sis_old_set_piomode - Initialize host controller PATA PIO timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device we are configuring for.
+ *
+ *      Set PIO mode for device, in host controller PCI config space. This
+ *      function handles PIO set up for all chips that are pre ATA100 and
+ *      also early ATA100 devices.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void sis_old_set_piomode (struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
+        int port = sis_port_base(adev);
+        u8 t1, t2;
+        int speed = adev->pio_mode - XFER_PIO_0;
+
+        const u8 active[]   = { 0x00, 0x07, 0x04, 0x03, 0x01 };
+        const u8 recovery[] = { 0x00, 0x06, 0x04, 0x03, 0x03 };
+
+        sis_set_fifo(ap, adev);
+
+        pci_read_config_byte(pdev, port, &t1);
+        pci_read_config_byte(pdev, port + 1, &t2);
+
+        t1 &= ~0x0F;    /* Clear active/recovery timings */
+        t2 &= ~0x07;
+
+        t1 |= active[speed];
+        t2 |= recovery[speed];
+
+        pci_write_config_byte(pdev, port, t1);
+        pci_write_config_byte(pdev, port + 1, t2);
+}
+
+/**
+ *      sis_100_set_pioode - Initialize host controller PATA PIO timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device we are configuring for.
+ *
+ *      Set PIO mode for device, in host controller PCI config space. This
+ *      function handles PIO set up for ATA100 devices and early ATA133.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void sis_100_set_piomode (struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
+        int port = sis_port_base(adev);
+        int speed = adev->pio_mode - XFER_PIO_0;
+
+        const u8 actrec[] = { 0x00, 0x67, 0x44, 0x33, 0x31 };
+
+        sis_set_fifo(ap, adev);
+
+        pci_write_config_byte(pdev, port, actrec[speed]);
+}
+
+/**
+ *      sis_133_set_pioode - Initialize host controller PATA PIO timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device we are configuring for.
+ *
+ *      Set PIO mode for device, in host controller PCI config space. This
+ *      function handles PIO set up for the later ATA133 devices.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void sis_133_set_piomode (struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
+        int port = 0x40;
+        u32 t1;
+        u32 reg54;
+        int speed = adev->pio_mode - XFER_PIO_0;
+
+        const u32 timing133[] = {
+                0x28269000,     /* Recovery << 24 | Act << 16 | Ini << 12 */
+                0x0C266000,
+                0x04263000,
+                0x0C0A3000,
+                0x05093000
+        };
+        const u32 timing100[] = {
+                0x1E1C6000,     /* Recovery << 24 | Act << 16 | Ini << 12 */
+                0x091C4000,
+                0x031C2000,
+                0x09072000,
+                0x04062000
+        };
+
+        sis_set_fifo(ap, adev);
+
+        /* If bit 14 is set then the registers are mapped at 0x70 not 0x40 */
+        pci_read_config_dword(pdev, 0x54, &reg54);
+        if (reg54 & 0x40000000)
+                port = 0x70;
+        port += 8 * ap->port_no +  4 * adev->devno;
+
+        pci_read_config_dword(pdev, port, &t1);
+        t1 &= 0xC0C00FFF;       /* Mask out timing */
+
+        if (t1 & 0x08)          /* 100 or 133 ? */
+                t1 |= timing133[speed];
+        else
+                t1 |= timing100[speed];
+        pci_write_config_byte(pdev, port, t1);
+}
+
+/**
+ *      sis_old_set_dmamode - Initialize host controller PATA DMA timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device to program
+ *
+ *      Set UDMA/MWDMA mode for device, in host controller PCI config space.
+ *      Handles pre UDMA and UDMA33 devices. Supports MWDMA as well unlike
+ *      the old ide/pci driver.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void sis_old_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
+        int speed = adev->dma_mode - XFER_MW_DMA_0;
+        int drive_pci = sis_port_base(adev);
+        u16 timing;
+
+        const u16 mwdma_bits[] = { 0x707, 0x202, 0x202 };
+        const u16 udma_bits[]  = { 0xE000, 0xC000, 0xA000 };
+
+        pci_read_config_word(pdev, drive_pci, &timing);
+
+        if (adev->dma_mode < XFER_UDMA_0) {
+                /* bits 3-0 hold recovery timing bits 8-10 active timing and
+                   the higer bits are dependant on the device */
+                timing &= ~ 0x870F;
+                timing |= mwdma_bits[speed];
+                pci_write_config_word(pdev, drive_pci, timing);
+        } else {
+                /* Bit 15 is UDMA on/off, bit 13-14 are cycle time */
+                speed = adev->dma_mode - XFER_UDMA_0;
+                timing &= ~0x6000;
+                timing |= udma_bits[speed];
+        }
+}
+
+/**
+ *      sis_66_set_dmamode - Initialize host controller PATA DMA timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device to program
+ *
+ *      Set UDMA/MWDMA mode for device, in host controller PCI config space.
+ *      Handles UDMA66 and early UDMA100 devices. Supports MWDMA as well unlike
+ *      the old ide/pci driver.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void sis_66_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
+        int speed = adev->dma_mode - XFER_MW_DMA_0;
+        int drive_pci = sis_port_base(adev);
+        u16 timing;
+
+        const u16 mwdma_bits[] = { 0x707, 0x202, 0x202 };
+        const u16 udma_bits[]  = { 0xF000, 0xD000, 0xB000, 0xA000, 0x9000};
+
+        pci_read_config_word(pdev, drive_pci, &timing);
+
+        if (adev->dma_mode < XFER_UDMA_0) {
+                /* bits 3-0 hold recovery timing bits 8-10 active timing and
+                   the higer bits are dependant on the device, bit 15 udma */
+                timing &= ~ 0x870F;
+                timing |= mwdma_bits[speed];
+        } else {
+                /* Bit 15 is UDMA on/off, bit 12-14 are cycle time */
+                speed = adev->dma_mode - XFER_UDMA_0;
+                timing &= ~0x6000;
+                timing |= udma_bits[speed];
+        }
+        pci_write_config_word(pdev, drive_pci, timing);
+}
+
+/**
+ *      sis_100_set_dmamode - Initialize host controller PATA DMA timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device to program
+ *
+ *      Set UDMA/MWDMA mode for device, in host controller PCI config space.
+ *      Handles UDMA66 and early UDMA100 devices.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void sis_100_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
+        int speed = adev->dma_mode - XFER_MW_DMA_0;
+        int drive_pci = sis_port_base(adev);
+        u16 timing;
+
+        const u16 udma_bits[]  = { 0x8B00, 0x8700, 0x8500, 0x8300, 0x8200, 0x8100};
+
+        pci_read_config_word(pdev, drive_pci, &timing);
+
+        if (adev->dma_mode < XFER_UDMA_0) {
+                /* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */
+        } else {
+                /* Bit 15 is UDMA on/off, bit 12-14 are cycle time */
+                speed = adev->dma_mode - XFER_UDMA_0;
+                timing &= ~0x0F00;
+                timing |= udma_bits[speed];
+        }
+        pci_write_config_word(pdev, drive_pci, timing);
+}
+
+/**
+ *      sis_133_early_set_dmamode - Initialize host controller PATA DMA timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device to program
+ *
+ *      Set UDMA/MWDMA mode for device, in host controller PCI config space.
+ *      Handles early SiS 961 bridges. Supports MWDMA as well unlike
+ *      the old ide/pci driver.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void sis_133_early_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
+        int speed = adev->dma_mode - XFER_MW_DMA_0;
+        int drive_pci = sis_port_base(adev);
+        u16 timing;
+
+        const u16 udma_bits[]  = { 0x8F00, 0x8A00, 0x8700, 0x8500, 0x8300, 0x8200, 0x8100};
+
+        pci_read_config_word(pdev, drive_pci, &timing);
+
+        if (adev->dma_mode < XFER_UDMA_0) {
+                /* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */
+        } else {
+                /* Bit 15 is UDMA on/off, bit 12-14 are cycle time */
+                speed = adev->dma_mode - XFER_UDMA_0;
+                timing &= ~0x0F00;
+                timing |= udma_bits[speed];
+        }
+        pci_write_config_word(pdev, drive_pci, timing);
+}
+
+/**
+ *      sis_133_set_dmamode - Initialize host controller PATA DMA timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device to program
+ *
+ *      Set UDMA/MWDMA mode for device, in host controller PCI config space.
+ *      Handles early SiS 961 bridges. Supports MWDMA as well unlike
+ *      the old ide/pci driver.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void sis_133_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
+        int speed = adev->dma_mode - XFER_MW_DMA_0;
+        int port = 0x40;
+        u32 t1;
+        u32 reg54;
+
+        /* bits 4- cycle time 8 - cvs time */
+        const u32 timing_u100[] = { 0x6B0, 0x470, 0x350, 0x140, 0x120, 0x110, 0x000 };
+        const u32 timing_u133[] = { 0x9F0, 0x6A0, 0x470, 0x250, 0x230, 0x220, 0x210 };
+
+        /* If bit 14 is set then the registers are mapped at 0x70 not 0x40 */
+        pci_read_config_dword(pdev, 0x54, &reg54);
+        if (reg54 & 0x40000000)
+                port = 0x70;
+        port += (8 * ap->port_no) +  (4 * adev->devno);
+
+        pci_read_config_dword(pdev, port, &t1);
+
+        if (adev->dma_mode < XFER_UDMA_0) {
+                t1 &= ~0x00000004;
+                /* FIXME: need data sheet to add MWDMA here. Also lacking on
+                   ide/pci driver */
+        } else {
+                speed = adev->dma_mode - XFER_UDMA_0;
+                /* if & 8 no UDMA133 - need info for ... */
+                t1 &= ~0x00000FF0;
+                t1 |= 0x00000004;
+                if (t1 & 0x08)
+                        t1 |= timing_u133[speed];
+                else
+                        t1 |= timing_u100[speed];
+        }
+        pci_write_config_dword(pdev, port, t1);
+}
+
+static struct scsi_host_template sis_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static const struct ata_port_operations sis_133_ops = {
+        .port_disable           = ata_port_disable,
+        .set_piomode            = sis_133_set_piomode,
+        .set_dmamode            = sis_133_set_dmamode,
+        .mode_filter            = ata_pci_default_filter,
+
+        .tf_load                = ata_tf_load,
+        .tf_read                = ata_tf_read,
+        .check_status           = ata_check_status,
+        .exec_command           = ata_exec_command,
+        .dev_select             = ata_std_dev_select,
+
+        .freeze                 = ata_bmdma_freeze,
+        .thaw                   = ata_bmdma_thaw,
+        .error_handler          = sis_133_error_handler,
+        .post_internal_cmd      = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup            = ata_bmdma_setup,
+        .bmdma_start            = ata_bmdma_start,
+        .bmdma_stop             = ata_bmdma_stop,
+        .bmdma_status           = ata_bmdma_status,
+        .qc_prep                = ata_qc_prep,
+        .qc_issue               = ata_qc_issue_prot,
+        .data_xfer              = ata_pio_data_xfer,
+
+        .eng_timeout            = ata_eng_timeout,
+
+        .irq_handler            = ata_interrupt,
+        .irq_clear              = ata_bmdma_irq_clear,
+
+        .port_start             = ata_port_start,
+        .port_stop              = ata_port_stop,
+        .host_stop              = ata_host_stop,
+};
+
+static const struct ata_port_operations sis_133_early_ops = {
+        .port_disable           = ata_port_disable,
+        .set_piomode            = sis_100_set_piomode,
+        .set_dmamode            = sis_133_early_set_dmamode,
+        .mode_filter            = ata_pci_default_filter,
+
+        .tf_load                = ata_tf_load,
+        .tf_read                = ata_tf_read,
+        .check_status           = ata_check_status,
+        .exec_command           = ata_exec_command,
+        .dev_select             = ata_std_dev_select,
+
+        .freeze                 = ata_bmdma_freeze,
+        .thaw                   = ata_bmdma_thaw,
+        .error_handler          = sis_66_error_handler,
+        .post_internal_cmd      = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup            = ata_bmdma_setup,
+        .bmdma_start            = ata_bmdma_start,
+        .bmdma_stop             = ata_bmdma_stop,
+        .bmdma_status           = ata_bmdma_status,
+        .qc_prep                = ata_qc_prep,
+        .qc_issue               = ata_qc_issue_prot,
+        .data_xfer              = ata_pio_data_xfer,
+
+        .eng_timeout            = ata_eng_timeout,
+
+        .irq_handler            = ata_interrupt,
+        .irq_clear              = ata_bmdma_irq_clear,
+
+        .port_start             = ata_port_start,
+        .port_stop              = ata_port_stop,
+        .host_stop              = ata_host_stop,
+};
+
+static const struct ata_port_operations sis_100_ops = {
+        .port_disable           = ata_port_disable,
+        .set_piomode            = sis_100_set_piomode,
+        .set_dmamode            = sis_100_set_dmamode,
+        .mode_filter            = ata_pci_default_filter,
+
+        .tf_load                = ata_tf_load,
+        .tf_read                = ata_tf_read,
+        .check_status           = ata_check_status,
+        .exec_command           = ata_exec_command,
+        .dev_select             = ata_std_dev_select,
+
+        .freeze                 = ata_bmdma_freeze,
+        .thaw                   = ata_bmdma_thaw,
+        .error_handler          = sis_66_error_handler,
+        .post_internal_cmd      = ata_bmdma_post_internal_cmd,
+
+
+        .bmdma_setup            = ata_bmdma_setup,
+        .bmdma_start            = ata_bmdma_start,
+        .bmdma_stop             = ata_bmdma_stop,
+        .bmdma_status           = ata_bmdma_status,
+        .qc_prep                = ata_qc_prep,
+        .qc_issue               = ata_qc_issue_prot,
+        .data_xfer              = ata_pio_data_xfer,
+
+        .eng_timeout            = ata_eng_timeout,
+
+        .irq_handler            = ata_interrupt,
+        .irq_clear              = ata_bmdma_irq_clear,
+
+        .port_start             = ata_port_start,
+        .port_stop              = ata_port_stop,
+        .host_stop              = ata_host_stop,
+};
+
+static const struct ata_port_operations sis_66_ops = {
+        .port_disable           = ata_port_disable,
+        .set_piomode            = sis_old_set_piomode,
+        .set_dmamode            = sis_66_set_dmamode,
+        .mode_filter            = ata_pci_default_filter,
+
+        .tf_load                = ata_tf_load,
+        .tf_read                = ata_tf_read,
+        .check_status           = ata_check_status,
+        .exec_command           = ata_exec_command,
+        .dev_select             = ata_std_dev_select,
+
+        .freeze                 = ata_bmdma_freeze,
+        .thaw                   = ata_bmdma_thaw,
+        .error_handler          = sis_66_error_handler,
+        .post_internal_cmd      = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup            = ata_bmdma_setup,
+        .bmdma_start            = ata_bmdma_start,
+        .bmdma_stop             = ata_bmdma_stop,
+        .bmdma_status           = ata_bmdma_status,
+        .qc_prep                = ata_qc_prep,
+        .qc_issue               = ata_qc_issue_prot,
+        .data_xfer              = ata_pio_data_xfer,
+
+        .eng_timeout            = ata_eng_timeout,
+
+        .irq_handler            = ata_interrupt,
+        .irq_clear              = ata_bmdma_irq_clear,
+
+        .port_start             = ata_port_start,
+        .port_stop              = ata_port_stop,
+        .host_stop              = ata_host_stop,
+};
+
+static const struct ata_port_operations sis_old_ops = {
+        .port_disable           = ata_port_disable,
+        .set_piomode            = sis_old_set_piomode,
+        .set_dmamode            = sis_old_set_dmamode,
+        .mode_filter            = ata_pci_default_filter,
+
+        .tf_load                = ata_tf_load,
+        .tf_read                = ata_tf_read,
+        .check_status           = ata_check_status,
+        .exec_command           = ata_exec_command,
+        .dev_select             = ata_std_dev_select,
+
+        .freeze                 = ata_bmdma_freeze,
+        .thaw                   = ata_bmdma_thaw,
+        .error_handler          = sis_old_error_handler,
+        .post_internal_cmd      = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup            = ata_bmdma_setup,
+        .bmdma_start            = ata_bmdma_start,
+        .bmdma_stop             = ata_bmdma_stop,
+        .bmdma_status           = ata_bmdma_status,
+        .qc_prep                = ata_qc_prep,
+        .qc_issue               = ata_qc_issue_prot,
+        .data_xfer              = ata_pio_data_xfer,
+
+        .eng_timeout            = ata_eng_timeout,
+
+        .irq_handler            = ata_interrupt,
+        .irq_clear              = ata_bmdma_irq_clear,
+
+        .port_start             = ata_port_start,
+        .port_stop              = ata_port_stop,
+        .host_stop              = ata_host_stop,
+};
+
+static struct ata_port_info sis_info = {
+        .sht            = &sis_sht,
+        .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+        .pio_mask       = 0x1f, /* pio0-4 */
+        .mwdma_mask     = 0x07,
+        .udma_mask      = 0,
+        .port_ops       = &sis_old_ops,
+};
+static struct ata_port_info sis_info33 = {
+        .sht            = &sis_sht,
+        .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+        .pio_mask       = 0x1f, /* pio0-4 */
+        .mwdma_mask     = 0x07,
+        .udma_mask      = ATA_UDMA2,    /* UDMA 33 */
+        .port_ops       = &sis_old_ops,
+};
+static struct ata_port_info sis_info66 = {
+        .sht            = &sis_sht,
+        .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+        .pio_mask       = 0x1f, /* pio0-4 */
+        .udma_mask      = ATA_UDMA4,    /* UDMA 66 */
+        .port_ops       = &sis_66_ops,
+};
+static struct ata_port_info sis_info100 = {
+        .sht            = &sis_sht,
+        .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+        .pio_mask       = 0x1f, /* pio0-4 */
+        .udma_mask      = ATA_UDMA5,
+        .port_ops       = &sis_100_ops,
+};
+static struct ata_port_info sis_info100_early = {
+        .sht            = &sis_sht,
+        .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+        .udma_mask      = ATA_UDMA5,
+        .pio_mask       = 0x1f, /* pio0-4 */
+        .port_ops       = &sis_66_ops,
+};
+static struct ata_port_info sis_info133 = {
+        .sht            = &sis_sht,
+        .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+        .pio_mask       = 0x1f, /* pio0-4 */
+        .udma_mask      = ATA_UDMA6,
+        .port_ops       = &sis_133_ops,
+};
+static struct ata_port_info sis_info133_early = {
+        .sht            = &sis_sht,
+        .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+        .pio_mask       = 0x1f, /* pio0-4 */
+        .udma_mask      = ATA_UDMA6,
+        .port_ops       = &sis_133_early_ops,
+};
+
+
+static void sis_fixup(struct pci_dev *pdev, struct sis_chipset *sis)
+{
+        u16 regw;
+        u8 reg;
+
+        if (sis->info == &sis_info133) {
+                pci_read_config_word(pdev, 0x50, &regw);
+                if (regw & 0x08)
+                        pci_write_config_word(pdev, 0x50, regw & ~0x08);
+                pci_read_config_word(pdev, 0x52, &regw);
+                if (regw & 0x08)
+                        pci_write_config_word(pdev, 0x52, regw & ~0x08);
+                return;
+        }
+
+        if (sis->info == &sis_info133_early || sis->info == &sis_info100) {
+                /* Fix up latency */
+                pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x80);
+                /* Set compatibility bit */
+                pci_read_config_byte(pdev, 0x49, &reg);
+                if (!(reg & 0x01))
+                        pci_write_config_byte(pdev, 0x49, reg | 0x01);
+                return;
+        }
+
+        if (sis->info == &sis_info66 || sis->info == &sis_info100_early) {
+                /* Fix up latency */
+                pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x80);
+                /* Set compatibility bit */
+                pci_read_config_byte(pdev, 0x52, &reg);
+                if (!(reg & 0x04))
+                        pci_write_config_byte(pdev, 0x52, reg | 0x04);
+                return;
+        }
+
+        if (sis->info == &sis_info33) {
+                pci_read_config_byte(pdev, PCI_CLASS_PROG, &reg);
+                if (( reg & 0x0F ) != 0x00)
+                        pci_write_config_byte(pdev, PCI_CLASS_PROG, reg & 0xF0);
+                /* Fall through to ATA16 fixup below */
+        }
+
+        if (sis->info == &sis_info || sis->info == &sis_info33) {
+                /* force per drive recovery and active timings
+                   needed on ATA_33 and below chips */
+                pci_read_config_byte(pdev, 0x52, &reg);
+                if (!(reg & 0x08))
+                        pci_write_config_byte(pdev, 0x52, reg|0x08);
+                return;
+        }
+
+        BUG();
+}
+
+/**
+ *      sis_init_one - Register SiS ATA PCI device with kernel services
+ *      @pdev: PCI device to register
+ *      @ent: Entry in sis_pci_tbl matching with @pdev
+ *
+ *      Called from kernel PCI layer.  We probe for combined mode (sigh),
+ *      and then hand over control to libata, for it to do the rest.
+ *
+ *      LOCKING:
+ *      Inherited from PCI layer (may sleep).
+ *
+ *      RETURNS:
+ *      Zero on success, or -ERRNO value.
+ */
+
+static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+        static int printed_version;
+        static struct ata_port_info *port_info[2];
+        struct ata_port_info *port;
+        struct pci_dev *host = NULL;
+        struct sis_chipset *chipset = NULL;
+
+        static struct sis_chipset sis_chipsets[] = {
+                { 0x0745, &sis_info100 },
+                { 0x0735, &sis_info100 },
+                { 0x0733, &sis_info100 },
+                { 0x0635, &sis_info100 },
+                { 0x0633, &sis_info100 },
+
+                { 0x0730, &sis_info100_early }, /* 100 with ATA 66 layout */
+                { 0x0550, &sis_info100_early }, /* 100 with ATA 66 layout */
+
+                { 0x0640, &sis_info66 },
+                { 0x0630, &sis_info66 },
+                { 0x0620, &sis_info66 },
+                { 0x0540, &sis_info66 },
+                { 0x0530, &sis_info66 },
+
+                { 0x5600, &sis_info33 },
+                { 0x5598, &sis_info33 },
+                { 0x5597, &sis_info33 },
+                { 0x5591, &sis_info33 },
+                { 0x5582, &sis_info33 },
+                { 0x5581, &sis_info33 },
+
+                { 0x5596, &sis_info },
+                { 0x5571, &sis_info },
+                { 0x5517, &sis_info },
+                { 0x5511, &sis_info },
+
+                {0}
+        };
+        static struct sis_chipset sis133_early = {
+                0x0, &sis_info133_early
+        };
+        static struct sis_chipset sis133 = {
+                0x0, &sis_info133
+        };
+        static struct sis_chipset sis100_early = {
+                0x0, &sis_info100_early
+        };
+        static struct sis_chipset sis100 = {
+                0x0, &sis_info100
+        };
+
+        if (!printed_version++)
+                dev_printk(KERN_DEBUG, &pdev->dev,
+                           "version " DRV_VERSION "\n");
+
+        /* We have to find the bridge first */
+
+        for (chipset = &sis_chipsets[0]; chipset->device; chipset++) {
+                host = pci_get_device(PCI_VENDOR_ID_SI, chipset->device, NULL);
+                if (host != NULL) {
+                        if (chipset->device == 0x630) { /* SIS630 */
+                                u8 host_rev;
+                                pci_read_config_byte(host, PCI_REVISION_ID, &host_rev);
+                                if (host_rev >= 0x30)   /* 630 ET */
+                                        chipset = &sis100_early;
+                        }
+                        break;
+                }
+        }
+
+        /* Look for concealed bridges */
+        if (host == NULL) {
+                /* Second check */
+                u32 idemisc;
+                u16 trueid;
+
+                /* Disable ID masking and register remapping then
+                   see what the real ID is */
+
+                pci_read_config_dword(pdev, 0x54, &idemisc);
+                pci_write_config_dword(pdev, 0x54, idemisc & 0x7fffffff);
+                pci_read_config_word(pdev, PCI_DEVICE_ID, &trueid);
+                pci_write_config_dword(pdev, 0x54, idemisc);
+
+                switch(trueid) {
+                case 0x5518:    /* SIS 962/963 */
+                        chipset = &sis133;
+                        if ((idemisc & 0x40000000) == 0) {
+                                pci_write_config_dword(pdev, 0x54, idemisc | 0x40000000);
+                                printk(KERN_INFO "SIS5513: Switching to 5513 register mapping\n");
+                        }
+                        break;
+                case 0x0180:    /* SIS 965/965L */
+                        chipset =  &sis133;
+                        break;
+                case 0x1180:    /* SIS 966/966L */
+                        chipset =  &sis133;
+                        break;
+                }
+        }
+
+        /* Further check */
+        if (chipset == NULL) {
+                struct pci_dev *lpc_bridge;
+                u16 trueid;
+                u8 prefctl;
+                u8 idecfg;
+                u8 sbrev;
+
+                /* Try the second unmasking technique */
+                pci_read_config_byte(pdev, 0x4a, &idecfg);
+                pci_write_config_byte(pdev, 0x4a, idecfg | 0x10);
+                pci_read_config_word(pdev, PCI_DEVICE_ID, &trueid);
+                pci_write_config_byte(pdev, 0x4a, idecfg);
+
+                switch(trueid) {
+                case 0x5517:
+                        lpc_bridge = pci_get_slot(pdev->bus, 0x10); /* Bus 0 Dev 2 Fn 0 */
+                        if (lpc_bridge == NULL)
+                                break;
+                        pci_read_config_byte(lpc_bridge, PCI_REVISION_ID, &sbrev);
+                        pci_read_config_byte(pdev, 0x49, &prefctl);
+                        pci_dev_put(lpc_bridge);
+
+                        if (sbrev == 0x10 && (prefctl & 0x80)) {
+                                chipset = &sis133_early;
+                                break;
+                        }
+                        chipset = &sis100;
+                        break;
+                }
+        }
+        pci_dev_put(host);
+
+        /* No chipset info, no support */
+        if (chipset == NULL)
+                return -ENODEV;
+
+        port = chipset->info;
+        port->private_data = chipset;
+
+        sis_fixup(pdev, chipset);
+
+        port_info[0] = port_info[1] = port;
+        return ata_pci_init_one(pdev, port_info, 2);
+}
+
+static const struct pci_device_id sis_pci_tbl[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_SI, 0x5513), },      /* SiS 5513 */
+        { PCI_DEVICE(PCI_VENDOR_ID_SI, 0x5518), },      /* SiS 5518 */
+        { }
+};
+
+static struct pci_driver sis_pci_driver = {
+        .name                   = DRV_NAME,
+        .id_table               = sis_pci_tbl,
+        .probe                  = sis_init_one,
+        .remove                 = ata_pci_remove_one,
+};
+
+static int __init sis_init(void)
+{
+        return pci_register_driver(&sis_pci_driver);
+}
+
+static void __exit sis_exit(void)
+{
+        pci_unregister_driver(&sis_pci_driver);
+}
+
+
+module_init(sis_init);
+module_exit(sis_exit);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("SCSI low-level driver for SiS ATA");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, sis_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+
diff --git a/drivers/ata/pata_sl82c105.c b/drivers/ata/pata_sl82c105.c
new file mode 100644
index 000000000000..f8499786917a
--- /dev/null
+++ b/drivers/ata/pata_sl82c105.c
@@ -0,0 +1,388 @@
+/*
+ * pata_sl82c105.c      - SL82C105 PATA for new ATA layer
+ *                        (C) 2005 Red Hat Inc
+ *                        Alan Cox <alan@redhat.com>
+ *
+ * Based in part on linux/drivers/ide/pci/sl82c105.c
+ *              SL82C105/Winbond 553 IDE driver
+ *
+ * and in part on the documentation and errata sheet
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_sl82c105"
+#define DRV_VERSION "0.2.2"
+
+enum {
+        /*
+         * SL82C105 PCI config register 0x40 bits.
+         */
+        CTRL_IDE_IRQB   =       (1 << 30),
+        CTRL_IDE_IRQA   =       (1 << 28),
+        CTRL_LEGIRQ     =       (1 << 11),
+        CTRL_P1F16      =       (1 << 5),
+        CTRL_P1EN       =       (1 << 4),
+        CTRL_P0F16      =       (1 << 1),
+        CTRL_P0EN       =       (1 << 0)
+};
+
+/**
+ *      sl82c105_pre_reset              -       probe begin
+ *      @ap: ATA port
+ *
+ *      Set up cable type and use generic probe init
+ */
+
+static int sl82c105_pre_reset(struct ata_port *ap)
+{
+        static const struct pci_bits sl82c105_enable_bits[] = {
+                { 0x40, 1, 0x01, 0x01 },
+                { 0x40, 1, 0x10, 0x10 }
+        };
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+        if (ap->port_no && !pci_test_config_bits(pdev, &sl82c105_enable_bits[ap->port_no])) {
+                ata_port_disable(ap);
+                dev_printk(KERN_INFO, &pdev->dev, "port disabled. ignoring.\n");
+                return 0;
+        }
+        ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+}
+
+
+static void sl82c105_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, sl82c105_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+
+/**
+ *      sl82c105_configure_piomode      -       set chip PIO timing
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *      @pio: PIO mode
+ *
+ *      Called to do the PIO mode setup. Our timing registers are shared
+ *      so a configure_dmamode call will undo any work we do here and vice
+ *      versa
+ */
+
+static void sl82c105_configure_piomode(struct ata_port *ap, struct ata_device *adev, int pio)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        static u16 pio_timing[5] = {
+                0x50D, 0x407, 0x304, 0x242, 0x240
+        };
+        u16 dummy;
+        int timing = 0x44 + (8 * ap->port_no) + (4 * adev->devno);
+
+        pci_write_config_word(pdev, timing, pio_timing[pio]);
+        /* Can we lose this oddity of the old driver */
+        pci_read_config_word(pdev, timing, &dummy);
+}
+
+/**
+ *      sl82c105_set_piomode    -       set initial PIO mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Called to do the PIO mode setup. Our timing registers are shared
+ *      but we want to set the PIO timing by default.
+ */
+
+static void sl82c105_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        sl82c105_configure_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
+}
+
+/**
+ *      sl82c105_configure_dmamode      -       set DMA mode in chip
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Load DMA cycle times into the chip ready for a DMA transfer
+ *      to occur.
+ */
+
+static void sl82c105_configure_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        static u16 dma_timing[3] = {
+                0x707, 0x201, 0x200
+        };
+        u16 dummy;
+        int timing = 0x44 + (8 * ap->port_no) + (4 * adev->devno);
+        int dma = adev->dma_mode - XFER_MW_DMA_0;
+
+        pci_write_config_word(pdev, timing, dma_timing[dma]);
+        /* Can we lose this oddity of the old driver */
+        pci_read_config_word(pdev, timing, &dummy);
+}
+
+/**
+ *      sl82c105_set_dmamode    -       set initial DMA mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Called to do the DMA mode setup. This replaces the PIO timings
+ *      for the device in question. Set appropriate PIO timings not DMA
+ *      timings at this point.
+ */
+
+static void sl82c105_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        switch(adev->dma_mode) {
+                case XFER_MW_DMA_0:
+                        sl82c105_configure_piomode(ap, adev, 1);
+                        break;
+                case XFER_MW_DMA_1:
+                        sl82c105_configure_piomode(ap, adev, 3);
+                        break;
+                case XFER_MW_DMA_2:
+                        sl82c105_configure_piomode(ap, adev, 3);
+                        break;
+                default:
+                        BUG();
+        }
+}
+
+/**
+ *      sl82c105_reset_engine   -       Reset the DMA engine
+ *      @ap: ATA interface
+ *
+ *      The sl82c105 has some serious problems with the DMA engine
+ *      when transfers don't run as expected or ATAPI is used. The
+ *      recommended fix is to reset the engine each use using a chip
+ *      test register.
+ */
+
+static void sl82c105_reset_engine(struct ata_port *ap)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u16 val;
+
+        pci_read_config_word(pdev, 0x7E, &val);
+        pci_write_config_word(pdev, 0x7E, val | 4);
+        pci_write_config_word(pdev, 0x7E, val & ~4);
+}
+
+/**
+ *      sl82c105_bmdma_start            -       DMA engine begin
+ *      @qc: ATA command
+ *
+ *      Reset the DMA engine each use as recommended by the errata
+ *      document.
+ *
+ *      FIXME: if we switch clock at BMDMA start/end we might get better
+ *      PIO performance on DMA capable devices.
+ */
+
+static void sl82c105_bmdma_start(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+
+        sl82c105_reset_engine(ap);
+
+        /* Set the clocks for DMA */
+        sl82c105_configure_dmamode(ap, qc->dev);
+        /* Activate DMA */
+        ata_bmdma_start(qc);
+}
+
+/**
+ *      sl82c105_bmdma_end              -       DMA engine stop
+ *      @qc: ATA command
+ *
+ *      Reset the DMA engine each use as recommended by the errata
+ *      document.
+ *
+ *      This function is also called to turn off DMA when a timeout occurs
+ *      during DMA operation. In both cases we need to reset the engine,
+ *      so no actual eng_timeout handler is required.
+ *
+ *      We assume bmdma_stop is always called if bmdma_start as called. If
+ *      not then we may need to wrap qc_issue.
+ */
+
+static void sl82c105_bmdma_stop(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+
+        ata_bmdma_stop(qc);
+        sl82c105_reset_engine(ap);
+
+        /* This will redo the initial setup of the DMA device to matching
+           PIO timings */
+        sl82c105_set_dmamode(ap, qc->dev);
+}
+
+static struct scsi_host_template sl82c105_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations sl82c105_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = sl82c105_set_piomode,
+        .set_dmamode    = sl82c105_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .error_handler  = sl82c105_error_handler,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = sl82c105_bmdma_start,
+        .bmdma_stop     = sl82c105_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/**
+ *      sl82c105_bridge_revision        -       find bridge version
+ *      @pdev: PCI device for the ATA function
+ *
+ *      Locates the PCI bridge associated with the ATA function and
+ *      providing it is a Winbond 553 reports the revision. If it cannot
+ *      find a revision or the right device it returns -1
+ */
+
+static int sl82c105_bridge_revision(struct pci_dev *pdev)
+{
+        struct pci_dev *bridge;
+        u8 rev;
+
+        /*
+         * The bridge should be part of the same device, but function 0.
+         */
+        bridge = pci_get_slot(pdev->bus,
+                               PCI_DEVFN(PCI_SLOT(pdev->devfn), 0));
+        if (!bridge)
+                return -1;
+
+        /*
+         * Make sure it is a Winbond 553 and is an ISA bridge.
+         */
+        if (bridge->vendor != PCI_VENDOR_ID_WINBOND ||
+            bridge->device != PCI_DEVICE_ID_WINBOND_83C553 ||
+            bridge->class >> 8 != PCI_CLASS_BRIDGE_ISA) {
+                pci_dev_put(bridge);
+                return -1;
+        }
+        /*
+         * We need to find function 0's revision, not function 1
+         */
+        pci_read_config_byte(bridge, PCI_REVISION_ID, &rev);
+
+        pci_dev_put(bridge);
+        return rev;
+}
+
+
+static int sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+        static struct ata_port_info info_dma = {
+                .sht = &sl82c105_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .port_ops = &sl82c105_port_ops
+        };
+        static struct ata_port_info info_early = {
+                .sht = &sl82c105_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .port_ops = &sl82c105_port_ops
+        };
+        static struct ata_port_info *port_info[2] = { &info_early, &info_early };
+        u32 val;
+        int rev;
+
+        rev = sl82c105_bridge_revision(dev);
+
+        if (rev == -1)
+                dev_printk(KERN_WARNING, &dev->dev, "pata_sl82c105: Unable to find bridge, disabling DMA.\n");
+        else if (rev <= 5)
+                dev_printk(KERN_WARNING, &dev->dev, "pata_sl82c105: Early bridge revision, no DMA available.\n");
+        else {
+                port_info[0] = &info_dma;
+                port_info[1] = &info_dma;
+        }
+
+        pci_read_config_dword(dev, 0x40, &val);
+        val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16;
+        pci_write_config_dword(dev, 0x40, val);
+
+
+        return ata_pci_init_one(dev, port_info, 1); /* For now */
+}
+
+static struct pci_device_id sl82c105[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_WINBOND, PCI_DEVICE_ID_WINBOND_82C105), },
+        { 0, },
+};
+
+static struct pci_driver sl82c105_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = sl82c105,
+        .probe          = sl82c105_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init sl82c105_init(void)
+{
+        return pci_register_driver(&sl82c105_pci_driver);
+}
+
+
+static void __exit sl82c105_exit(void)
+{
+        pci_unregister_driver(&sl82c105_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for Sl82c105");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, sl82c105);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(sl82c105_init);
+module_exit(sl82c105_exit);
diff --git a/drivers/ata/pata_triflex.c b/drivers/ata/pata_triflex.c
new file mode 100644
index 000000000000..36f788728f3f
--- /dev/null
+++ b/drivers/ata/pata_triflex.c
@@ -0,0 +1,285 @@
+/*
+ * pata_triflex.c       - Compaq PATA for new ATA layer
+ *                        (C) 2005 Red Hat Inc
+ *                        Alan Cox <alan@redhat.com>
+ *
+ * based upon
+ *
+ * triflex.c
+ *
+ * IDE Chipset driver for the Compaq TriFlex IDE controller.
+ *
+ * Known to work with the Compaq Workstation 5x00 series.
+ *
+ * Copyright (C) 2002 Hewlett-Packard Development Group, L.P.
+ * Author: Torben Mathiasen <torben.mathiasen@hp.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ * Loosely based on the piix & svwks drivers.
+ *
+ * Documentation:
+ *      Not publically available.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_triflex"
+#define DRV_VERSION "0.2.5"
+
+/**
+ *      triflex_probe_init              -       probe begin
+ *      @ap: ATA port
+ *
+ *      Set up cable type and use generic probe init
+ */
+
+static int triflex_probe_init(struct ata_port *ap)
+{
+        static const struct pci_bits triflex_enable_bits[] = {
+                { 0x80, 1, 0x01, 0x01 },
+                { 0x80, 1, 0x02, 0x02 }
+        };
+
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+        if (!pci_test_config_bits(pdev, &triflex_enable_bits[ap->port_no])) {
+                ata_port_disable(ap);
+                printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+                return 0;
+        }
+        ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+}
+
+
+
+static void triflex_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, triflex_probe_init, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      triflex_load_timing             -       timing configuration
+ *      @ap: ATA interface
+ *      @adev: Device on the bus
+ *      @speed: speed to configure
+ *
+ *      The Triflex has one set of timings per device per channel. This
+ *      means we must do some switching. As the PIO and DMA timings don't
+ *      match we have to do some reloading unlike PIIX devices where tuning
+ *      tricks can avoid it.
+ */
+
+static void triflex_load_timing(struct ata_port *ap, struct ata_device *adev, int speed)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u32 timing = 0;
+        u32 triflex_timing, old_triflex_timing;
+        int channel_offset = ap->port_no ? 0x74: 0x70;
+        unsigned int is_slave   = (adev->devno != 0);
+
+
+        pci_read_config_dword(pdev, channel_offset, &old_triflex_timing);
+        triflex_timing = old_triflex_timing;
+
+        switch(speed)
+        {
+                case XFER_MW_DMA_2:
+                        timing = 0x0103;break;
+                case XFER_MW_DMA_1:
+                        timing = 0x0203;break;
+                case XFER_MW_DMA_0:
+                        timing = 0x0808;break;
+                case XFER_SW_DMA_2:
+                case XFER_SW_DMA_1:
+                case XFER_SW_DMA_0:
+                        timing = 0x0F0F;break;
+                case XFER_PIO_4:
+                        timing = 0x0202;break;
+                case XFER_PIO_3:
+                        timing = 0x0204;break;
+                case XFER_PIO_2:
+                        timing = 0x0404;break;
+                case XFER_PIO_1:
+                        timing = 0x0508;break;
+                case XFER_PIO_0:
+                        timing = 0x0808;break;
+                default:
+                        BUG();
+        }
+        triflex_timing &= ~ (0xFFFF << (16 * is_slave));
+        triflex_timing |= (timing << (16 * is_slave));
+
+        if (triflex_timing != old_triflex_timing)
+                pci_write_config_dword(pdev, channel_offset, triflex_timing);
+}
+
+/**
+ *      triflex_set_piomode     -       set initial PIO mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      Use the timing loader to set up the PIO mode. We have to do this
+ *      because DMA start/stop will only be called once DMA occurs. If there
+ *      has been no DMA then the PIO timings are still needed.
+ */
+static void triflex_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        triflex_load_timing(ap, adev, adev->pio_mode);
+}
+
+/**
+ *      triflex_dma_start       -       DMA start callback
+ *      @qc: Command in progress
+ *
+ *      Usually drivers set the DMA timing at the point the set_dmamode call
+ *      is made. Triflex however requires we load new timings on the
+ *      transition or keep matching PIO/DMA pairs (ie MWDMA2/PIO4 etc).
+ *      We load the DMA timings just before starting DMA and then restore
+ *      the PIO timing when the DMA is finished.
+ */
+
+static void triflex_bmdma_start(struct ata_queued_cmd *qc)
+{
+        triflex_load_timing(qc->ap, qc->dev, qc->dev->dma_mode);
+        ata_bmdma_start(qc);
+}
+
+/**
+ *      triflex_dma_stop        -       DMA stop callback
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *
+ *      We loaded new timings in dma_start, as a result we need to restore
+ *      the PIO timings in dma_stop so that the next command issue gets the
+ *      right clock values.
+ */
+
+static void triflex_bmdma_stop(struct ata_queued_cmd *qc)
+{
+        ata_bmdma_stop(qc);
+        triflex_load_timing(qc->ap, qc->dev, qc->dev->pio_mode);
+}
+
+static struct scsi_host_template triflex_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations triflex_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = triflex_set_piomode,
+        .mode_filter    = ata_pci_default_filter,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = triflex_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = triflex_bmdma_start,
+        .bmdma_stop     = triflex_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static int triflex_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+        static struct ata_port_info info = {
+                .sht = &triflex_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .port_ops = &triflex_port_ops
+        };
+        static struct ata_port_info *port_info[2] = { &info, &info };
+        static int printed_version;
+
+        if (!printed_version++)
+                dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n");
+
+        return ata_pci_init_one(dev, port_info, 2);
+}
+
+static const struct pci_device_id triflex[] = {
+        { PCI_VENDOR_ID_COMPAQ, PCI_DEVICE_ID_COMPAQ_TRIFLEX_IDE,
+                                  PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
+        { 0, },
+};
+
+static struct pci_driver triflex_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = triflex,
+        .probe          = triflex_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init triflex_init(void)
+{
+        return pci_register_driver(&triflex_pci_driver);
+}
+
+
+static void __exit triflex_exit(void)
+{
+        pci_unregister_driver(&triflex_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for Compaq Triflex");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, triflex);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(triflex_init);
+module_exit(triflex_exit);
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c
new file mode 100644
index 000000000000..1b2ff133b163
--- /dev/null
+++ b/drivers/ata/pata_via.c
@@ -0,0 +1,568 @@
+/*
+ * pata_via.c   - VIA PATA for new ATA layer
+ *                        (C) 2005-2006 Red Hat Inc
+ *                        Alan Cox <alan@redhat.com>
+ *
+ *  Documentation
+ *      Most chipset documentation available under NDA only
+ *
+ *  VIA version guide
+ *      VIA VT82C561    -       early design, uses ata_generic currently
+ *      VIA VT82C576    -       MWDMA, 33Mhz
+ *      VIA VT82C586    -       MWDMA, 33Mhz
+ *      VIA VT82C586a   -       Added UDMA to 33Mhz
+ *      VIA VT82C586b   -       UDMA33
+ *      VIA VT82C596a   -       Nonfunctional UDMA66
+ *      VIA VT82C596b   -       Working UDMA66
+ *      VIA VT82C686    -       Nonfunctional UDMA66
+ *      VIA VT82C686a   -       Working UDMA66
+ *      VIA VT82C686b   -       Updated to UDMA100
+ *      VIA VT8231      -       UDMA100
+ *      VIA VT8233      -       UDMA100
+ *      VIA VT8233a     -       UDMA133
+ *      VIA VT8233c     -       UDMA100
+ *      VIA VT8235      -       UDMA133
+ *      VIA VT8237      -       UDMA133
+ *
+ *      Most registers remain compatible across chips. Others start reserved
+ *      and acquire sensible semantics if set to 1 (eg cable detect). A few
+ *      exceptions exist, notably around the FIFO settings.
+ *
+ *      One additional quirk of the VIA design is that like ALi they use few
+ *      PCI IDs for a lot of chips.
+ *
+ *      Based heavily on:
+ *
+ * Version 3.38
+ *
+ * VIA IDE driver for Linux. Supported southbridges:
+ *
+ *   vt82c576, vt82c586, vt82c586a, vt82c586b, vt82c596a, vt82c596b,
+ *   vt82c686, vt82c686a, vt82c686b, vt8231, vt8233, vt8233c, vt8233a,
+ *   vt8235, vt8237
+ *
+ * Copyright (c) 2000-2002 Vojtech Pavlik
+ *
+ * Based on the work of:
+ *      Michel Aubry
+ *      Jeff Garzik
+ *      Andre Hedrick
+
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_via"
+#define DRV_VERSION "0.1.13"
+
+/*
+ *      The following comes directly from Vojtech Pavlik's ide/pci/via82cxxx
+ *      driver.
+ */
+
+enum {
+        VIA_UDMA        = 0x007,
+        VIA_UDMA_NONE   = 0x000,
+        VIA_UDMA_33     = 0x001,
+        VIA_UDMA_66     = 0x002,
+        VIA_UDMA_100    = 0x003,
+        VIA_UDMA_133    = 0x004,
+        VIA_BAD_PREQ    = 0x010, /* Crashes if PREQ# till DDACK# set */
+        VIA_BAD_CLK66   = 0x020, /* 66 MHz clock doesn't work correctly */
+        VIA_SET_FIFO    = 0x040, /* Needs to have FIFO split set */
+        VIA_NO_UNMASK   = 0x080, /* Doesn't work with IRQ unmasking on */
+        VIA_BAD_ID      = 0x100, /* Has wrong vendor ID (0x1107) */
+        VIA_BAD_AST     = 0x200, /* Don't touch Address Setup Timing */
+        VIA_NO_ENABLES  = 0x400, /* Has no enablebits */
+};
+
+/*
+ * VIA SouthBridge chips.
+ */
+
+static const struct via_isa_bridge {
+        const char *name;
+        u16 id;
+        u8 rev_min;
+        u8 rev_max;
+        u16 flags;
+} via_isa_bridges[] = {
+        { "cx700",      PCI_DEVICE_ID_VIA_CX700,    0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
+        { "vt6410",     PCI_DEVICE_ID_VIA_6410,     0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST | VIA_NO_ENABLES},
+        { "vt8237a",    PCI_DEVICE_ID_VIA_8237A,    0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
+        { "vt8237",     PCI_DEVICE_ID_VIA_8237,     0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
+        { "vt8235",     PCI_DEVICE_ID_VIA_8235,     0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
+        { "vt8233a",    PCI_DEVICE_ID_VIA_8233A,    0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
+        { "vt8233c",    PCI_DEVICE_ID_VIA_8233C_0,  0x00, 0x2f, VIA_UDMA_100 },
+        { "vt8233",     PCI_DEVICE_ID_VIA_8233_0,   0x00, 0x2f, VIA_UDMA_100 },
+        { "vt8231",     PCI_DEVICE_ID_VIA_8231,     0x00, 0x2f, VIA_UDMA_100 },
+        { "vt82c686b",  PCI_DEVICE_ID_VIA_82C686,   0x40, 0x4f, VIA_UDMA_100 },
+        { "vt82c686a",  PCI_DEVICE_ID_VIA_82C686,   0x10, 0x2f, VIA_UDMA_66 },
+        { "vt82c686",   PCI_DEVICE_ID_VIA_82C686,   0x00, 0x0f, VIA_UDMA_33 | VIA_BAD_CLK66 },
+        { "vt82c596b",  PCI_DEVICE_ID_VIA_82C596,   0x10, 0x2f, VIA_UDMA_66 },
+        { "vt82c596a",  PCI_DEVICE_ID_VIA_82C596,   0x00, 0x0f, VIA_UDMA_33 | VIA_BAD_CLK66 },
+        { "vt82c586b",  PCI_DEVICE_ID_VIA_82C586_0, 0x47, 0x4f, VIA_UDMA_33 | VIA_SET_FIFO },
+        { "vt82c586b",  PCI_DEVICE_ID_VIA_82C586_0, 0x40, 0x46, VIA_UDMA_33 | VIA_SET_FIFO | VIA_BAD_PREQ },
+        { "vt82c586b",  PCI_DEVICE_ID_VIA_82C586_0, 0x30, 0x3f, VIA_UDMA_33 | VIA_SET_FIFO },
+        { "vt82c586a",  PCI_DEVICE_ID_VIA_82C586_0, 0x20, 0x2f, VIA_UDMA_33 | VIA_SET_FIFO },
+        { "vt82c586",   PCI_DEVICE_ID_VIA_82C586_0, 0x00, 0x0f, VIA_UDMA_NONE | VIA_SET_FIFO },
+        { "vt82c576",   PCI_DEVICE_ID_VIA_82C576,   0x00, 0x2f, VIA_UDMA_NONE | VIA_SET_FIFO | VIA_NO_UNMASK },
+        { "vt82c576",   PCI_DEVICE_ID_VIA_82C576,   0x00, 0x2f, VIA_UDMA_NONE | VIA_SET_FIFO | VIA_NO_UNMASK | VIA_BAD_ID },
+        { NULL }
+};
+
+/**
+ *      via_cable_detect        -       cable detection
+ *      @ap: ATA port
+ *
+ *      Perform cable detection. Actually for the VIA case the BIOS
+ *      already did this for us. We read the values provided by the
+ *      BIOS. If you are using an 8235 in a non-PC configuration you
+ *      may need to update this code.
+ *
+ *      Hotplug also impacts on this.
+ */
+
+static int via_cable_detect(struct ata_port *ap) {
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u32 ata66;
+
+        pci_read_config_dword(pdev, 0x50, &ata66);
+        /* Check both the drive cable reporting bits, we might not have
+           two drives */
+        if (ata66 & (0x10100000 >> (16 * ap->port_no)))
+                return ATA_CBL_PATA80;
+        else
+                return ATA_CBL_PATA40;
+}
+
+static int via_pre_reset(struct ata_port *ap)
+{
+        const struct via_isa_bridge *config = ap->host->private_data;
+
+        if (!(config->flags & VIA_NO_ENABLES)) {
+                static const struct pci_bits via_enable_bits[] = {
+                        { 0x40, 1, 0x02, 0x02 },
+                        { 0x40, 1, 0x01, 0x01 }
+                };
+
+                struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+                if (!pci_test_config_bits(pdev, &via_enable_bits[ap->port_no])) {
+                        ata_port_disable(ap);
+                        printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+                        return 0;
+                }
+        }
+
+        if ((config->flags & VIA_UDMA) >= VIA_UDMA_66)
+                ap->cbl = via_cable_detect(ap);
+        else
+                ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+}
+
+
+/**
+ *      via_error_handler               -       reset for VIA chips
+ *      @ap: ATA port
+ *
+ *      Handle the reset callback for the later chips with cable detect
+ */
+
+static void via_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, via_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *      via_do_set_mode -       set initial PIO mode data
+ *      @ap: ATA interface
+ *      @adev: ATA device
+ *      @mode: ATA mode being programmed
+ *      @tdiv: Clocks per PCI clock
+ *      @set_ast: Set to program address setup
+ *      @udma_type: UDMA mode/format of registers
+ *
+ *      Program the VIA registers for DMA and PIO modes. Uses the ata timing
+ *      support in order to compute modes.
+ *
+ *      FIXME: Hotplug will require we serialize multiple mode changes
+ *      on the two channels.
+ */
+
+static void via_do_set_mode(struct ata_port *ap, struct ata_device *adev, int mode, int tdiv, int set_ast, int udma_type)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        struct ata_device *peer = ata_dev_pair(adev);
+        struct ata_timing t, p;
+        static int via_clock = 33333;   /* Bus clock in kHZ - ought to be tunable one day */
+        unsigned long T =  1000000000 / via_clock;
+        unsigned long UT = T/tdiv;
+        int ut;
+        int offset = 3 - (2*ap->port_no) - adev->devno;
+
+
+        /* Calculate the timing values we require */
+        ata_timing_compute(adev, mode, &t, T, UT);
+
+        /* We share 8bit timing so we must merge the constraints */
+        if (peer) {
+                if (peer->pio_mode) {
+                        ata_timing_compute(peer, peer->pio_mode, &p, T, UT);
+                        ata_timing_merge(&p, &t, &t, ATA_TIMING_8BIT);
+                }
+        }
+
+        /* Address setup is programmable but breaks on UDMA133 setups */
+        if (set_ast) {
+                u8 setup;       /* 2 bits per drive */
+                int shift = 2 * offset;
+
+                pci_read_config_byte(pdev, 0x4C, &setup);
+                setup &= ~(3 << shift);
+                setup |= FIT(t.setup, 1, 4) << shift;   /* 1,4 or 1,4 - 1  FIXME */
+                pci_write_config_byte(pdev, 0x4C, setup);
+        }
+
+        /* Load the PIO mode bits */
+        pci_write_config_byte(pdev, 0x4F - ap->port_no,
+                ((FIT(t.act8b, 1, 16) - 1) << 4) | (FIT(t.rec8b, 1, 16) - 1));
+        pci_write_config_byte(pdev, 0x48 + offset,
+                ((FIT(t.active, 1, 16) - 1) << 4) | (FIT(t.recover, 1, 16) - 1));
+
+        /* Load the UDMA bits according to type */
+        switch(udma_type) {
+                default:
+                        /* BUG() ? */
+                        /* fall through */
+                case 33:
+                        ut = t.udma ? (0xe0 | (FIT(t.udma, 2, 5) - 2)) : 0x03;
+                        break;
+                case 66:
+                        ut = t.udma ? (0xe8 | (FIT(t.udma, 2, 9) - 2)) : 0x0f;
+                        break;
+                case 100:
+                        ut = t.udma ? (0xe0 | (FIT(t.udma, 2, 9) - 2)) : 0x07;
+                        break;
+                case 133:
+                        ut = t.udma ? (0xe0 | (FIT(t.udma, 2, 9) - 2)) : 0x07;
+                        break;
+        }
+        /* Set UDMA unless device is not UDMA capable */
+        if (udma_type)
+                pci_write_config_byte(pdev, 0x50 + offset, ut);
+}
+
+static void via_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        const struct via_isa_bridge *config = ap->host->private_data;
+        int set_ast = (config->flags & VIA_BAD_AST) ? 0 : 1;
+        int mode = config->flags & VIA_UDMA;
+        static u8 tclock[5] = { 1, 1, 2, 3, 4 };
+        static u8 udma[5] = { 0, 33, 66, 100, 133 };
+
+        via_do_set_mode(ap, adev, adev->pio_mode, tclock[mode], set_ast, udma[mode]);
+}
+
+static void via_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        const struct via_isa_bridge *config = ap->host->private_data;
+        int set_ast = (config->flags & VIA_BAD_AST) ? 0 : 1;
+        int mode = config->flags & VIA_UDMA;
+        static u8 tclock[5] = { 1, 1, 2, 3, 4 };
+        static u8 udma[5] = { 0, 33, 66, 100, 133 };
+
+        via_do_set_mode(ap, adev, adev->dma_mode, tclock[mode], set_ast, udma[mode]);
+}
+
+static struct scsi_host_template via_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static struct ata_port_operations via_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = via_set_piomode,
+        .set_dmamode    = via_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = via_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+static struct ata_port_operations via_port_ops_noirq = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = via_set_piomode,
+        .set_dmamode    = via_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = via_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = ata_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = ata_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer_noirq,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};
+
+/**
+ *      via_init_one            -       discovery callback
+ *      @pdev: PCI device ID
+ *      @id: PCI table info
+ *
+ *      A VIA IDE interface has been discovered. Figure out what revision
+ *      and perform configuration work before handing it to the ATA layer
+ */
+
+static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+        /* Early VIA without UDMA support */
+        static struct ata_port_info via_mwdma_info = {
+                .sht = &via_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .port_ops = &via_port_ops
+        };
+        /* Ditto with IRQ masking required */
+        static struct ata_port_info via_mwdma_info_borked = {
+                .sht = &via_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .port_ops = &via_port_ops_noirq,
+        };
+        /* VIA UDMA 33 devices (and borked 66) */
+        static struct ata_port_info via_udma33_info = {
+                .sht = &via_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x7,
+                .port_ops = &via_port_ops
+        };
+        /* VIA UDMA 66 devices */
+        static struct ata_port_info via_udma66_info = {
+                .sht = &via_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x1f,
+                .port_ops = &via_port_ops
+        };
+        /* VIA UDMA 100 devices */
+        static struct ata_port_info via_udma100_info = {
+                .sht = &via_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x3f,
+                .port_ops = &via_port_ops
+        };
+        /* UDMA133 with bad AST (All current 133) */
+        static struct ata_port_info via_udma133_info = {
+                .sht = &via_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x7f,      /* FIXME: should check north bridge */
+                .port_ops = &via_port_ops
+        };
+        struct ata_port_info *port_info[2], *type;
+        struct pci_dev *isa = NULL;
+        const struct via_isa_bridge *config;
+        static int printed_version;
+        u8 t;
+        u8 enable;
+        u32 timing;
+
+        if (!printed_version++)
+                dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
+
+        /* To find out how the IDE will behave and what features we
+           actually have to look at the bridge not the IDE controller */
+        for (config = via_isa_bridges; config->id; config++)
+                if ((isa = pci_get_device(PCI_VENDOR_ID_VIA +
+                        !!(config->flags & VIA_BAD_ID),
+                        config->id, NULL))) {
+
+                        pci_read_config_byte(isa, PCI_REVISION_ID, &t);
+                        if (t >= config->rev_min &&
+                            t <= config->rev_max)
+                                break;
+                        pci_dev_put(isa);
+                }
+
+        if (!config->id) {
+                printk(KERN_WARNING "via: Unknown VIA SouthBridge, disabling.\n");
+                return -ENODEV;
+        }
+        pci_dev_put(isa);
+
+        /* 0x40 low bits indicate enabled channels */
+        pci_read_config_byte(pdev, 0x40 , &enable);
+        enable &= 3;
+        if (enable == 0) {
+                return -ENODEV;
+        }
+
+        /* Initialise the FIFO for the enabled channels. */
+        if (config->flags & VIA_SET_FIFO) {
+                u8 fifo_setting[4] = {0x00, 0x60, 0x00, 0x20};
+                u8 fifo;
+
+                pci_read_config_byte(pdev, 0x43, &fifo);
+
+                /* Clear PREQ# until DDACK# for errata */
+                if (config->flags & VIA_BAD_PREQ)
+                        fifo &= 0x7F;
+                else
+                        fifo &= 0x9f;
+                /* Turn on FIFO for enabled channels */
+                fifo |= fifo_setting[enable];
+                pci_write_config_byte(pdev, 0x43, fifo);
+        }
+        /* Clock set up */
+        switch(config->flags & VIA_UDMA) {
+                case VIA_UDMA_NONE:
+                        if (config->flags & VIA_NO_UNMASK)
+                                type = &via_mwdma_info_borked;
+                        else
+                                type = &via_mwdma_info;
+                        break;
+                case VIA_UDMA_33:
+                        type = &via_udma33_info;
+                        break;
+                case VIA_UDMA_66:
+                        type = &via_udma66_info;
+                        /* The 66 MHz devices require we enable the clock */
+                        pci_read_config_dword(pdev, 0x50, &timing);
+                        timing |= 0x80008;
+                        pci_write_config_dword(pdev, 0x50, timing);
+                        break;
+                case VIA_UDMA_100:
+                        type = &via_udma100_info;
+                        break;
+                case VIA_UDMA_133:
+                        type = &via_udma133_info;
+                        break;
+                default:
+                        WARN_ON(1);
+                        return -ENODEV;
+        }
+
+        if (config->flags & VIA_BAD_CLK66) {
+                /* Disable the 66MHz clock on problem devices */
+                pci_read_config_dword(pdev, 0x50, &timing);
+                timing &= ~0x80008;
+                pci_write_config_dword(pdev, 0x50, timing);
+        }
+
+        /* We have established the device type, now fire it up */
+        type->private_data = (void *)config;
+
+        port_info[0] = port_info[1] = type;
+        return ata_pci_init_one(pdev, port_info, 2);
+}
+
+static const struct pci_device_id via[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C576_1), },
+        { PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_1), },
+        { PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_6410), },
+        { PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_SATA_EIDE), },
+        { 0, },
+};
+
+static struct pci_driver via_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = via,
+        .probe          = via_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init via_init(void)
+{
+        return pci_register_driver(&via_pci_driver);
+}
+
+
+static void __exit via_exit(void)
+{
+        pci_unregister_driver(&via_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for VIA PATA");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, via);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(via_init);
+module_exit(via_exit);
diff --git a/drivers/scsi/pdc_adma.c b/drivers/ata/pdc_adma.c
index efc8fff1d250..0e23ecb77bc2 100644
--- a/drivers/scsi/pdc_adma.c
+++ b/drivers/ata/pdc_adma.c
@@ -127,7 +127,7 @@ static int adma_ata_init_one (struct pci_dev *pdev,
 static irqreturn_t adma_intr (int irq, void *dev_instance,
                                 struct pt_regs *regs);
 static int adma_port_start(struct ata_port *ap);
-static void adma_host_stop(struct ata_host_set *host_set);
+static void adma_host_stop(struct ata_host *host);
 static void adma_port_stop(struct ata_port *ap);
 static void adma_phy_reset(struct ata_port *ap);
 static void adma_qc_prep(struct ata_queued_cmd *qc);
@@ -182,7 +182,7 @@ static struct ata_port_info adma_port_info[] = {
         /* board_1841_idx */
         {
                 .sht            = &adma_ata_sht,
-                .host_flags     = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST |
+                .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST |
                                   ATA_FLAG_NO_LEGACY | ATA_FLAG_MMIO |
                                   ATA_FLAG_PIO_POLLING,
                 .pio_mask       = 0x10, /* pio4 */
@@ -237,7 +237,7 @@ static void adma_reset_engine(void __iomem *chan)
 static void adma_reinit_engine(struct ata_port *ap)
 {
         struct adma_port_priv *pp = ap->private_data;
-        void __iomem *mmio_base = ap->host_set->mmio_base;
+        void __iomem *mmio_base = ap->host->mmio_base;
         void __iomem *chan = ADMA_REGS(mmio_base, ap->port_no);
 
         /* mask/clear ATA interrupts */
@@ -265,7 +265,7 @@ static void adma_reinit_engine(struct ata_port *ap)
 
 static inline void adma_enter_reg_mode(struct ata_port *ap)
 {
-        void __iomem *chan = ADMA_REGS(ap->host_set->mmio_base, ap->port_no);
+        void __iomem *chan = ADMA_REGS(ap->host->mmio_base, ap->port_no);
 
         writew(aPIOMD4, chan + ADMA_CONTROL);
         readb(chan + ADMA_STATUS);      /* flush */
@@ -412,7 +412,7 @@ static void adma_qc_prep(struct ata_queued_cmd *qc)
 static inline void adma_packet_start(struct ata_queued_cmd *qc)
 {
         struct ata_port *ap = qc->ap;
-        void __iomem *chan = ADMA_REGS(ap->host_set->mmio_base, ap->port_no);
+        void __iomem *chan = ADMA_REGS(ap->host->mmio_base, ap->port_no);
 
         VPRINTK("ENTER, ap %p\n", ap);
 
@@ -442,13 +442,13 @@ static unsigned int adma_qc_issue(struct ata_queued_cmd *qc)
         return ata_qc_issue_prot(qc);
 }
 
-static inline unsigned int adma_intr_pkt(struct ata_host_set *host_set)
+static inline unsigned int adma_intr_pkt(struct ata_host *host)
 {
         unsigned int handled = 0, port_no;
-        u8 __iomem *mmio_base = host_set->mmio_base;
+        u8 __iomem *mmio_base = host->mmio_base;
 
-        for (port_no = 0; port_no < host_set->n_ports; ++port_no) {
-                struct ata_port *ap = host_set->ports[port_no];
+        for (port_no = 0; port_no < host->n_ports; ++port_no) {
+                struct ata_port *ap = host->ports[port_no];
                 struct adma_port_priv *pp;
                 struct ata_queued_cmd *qc;
                 void __iomem *chan = ADMA_REGS(mmio_base, port_no);
@@ -476,13 +476,13 @@ static inline unsigned int adma_intr_pkt(struct ata_host_set *host_set)
         return handled;
 }
 
-static inline unsigned int adma_intr_mmio(struct ata_host_set *host_set)
+static inline unsigned int adma_intr_mmio(struct ata_host *host)
 {
         unsigned int handled = 0, port_no;
 
-        for (port_no = 0; port_no < host_set->n_ports; ++port_no) {
+        for (port_no = 0; port_no < host->n_ports; ++port_no) {
                 struct ata_port *ap;
-                ap = host_set->ports[port_no];
+                ap = host->ports[port_no];
                 if (ap && (!(ap->flags & ATA_FLAG_DISABLED))) {
                         struct ata_queued_cmd *qc;
                         struct adma_port_priv *pp = ap->private_data;
@@ -497,7 +497,7 @@ static inline unsigned int adma_intr_mmio(struct ata_host_set *host_set)
                                         continue;
                                 DPRINTK("ata%u: protocol %d (dev_stat 0x%X)\n",
                                         ap->id, qc->tf.protocol, status);
-                
+
                                 /* complete taskfile transaction */
                                 pp->state = adma_state_idle;
                                 qc->err_mask |= ac_err_mask(status);
@@ -511,14 +511,14 @@ static inline unsigned int adma_intr_mmio(struct ata_host_set *host_set)
 
 static irqreturn_t adma_intr(int irq, void *dev_instance, struct pt_regs *regs)
 {
-        struct ata_host_set *host_set = dev_instance;
+        struct ata_host *host = dev_instance;
         unsigned int handled = 0;
 
         VPRINTK("ENTER\n");
 
-        spin_lock(&host_set->lock);
-        handled  = adma_intr_pkt(host_set) | adma_intr_mmio(host_set);
-        spin_unlock(&host_set->lock);
+        spin_lock(&host->lock);
+        handled  = adma_intr_pkt(host) | adma_intr_mmio(host);
+        spin_unlock(&host->lock);
 
         VPRINTK("EXIT\n");
 
@@ -544,7 +544,7 @@ static void adma_ata_setup_port(struct ata_ioports *port, unsigned long base)
 
 static int adma_port_start(struct ata_port *ap)
 {
-        struct device *dev = ap->host_set->dev;
+        struct device *dev = ap->host->dev;
         struct adma_port_priv *pp;
         int rc;
 
@@ -582,10 +582,10 @@ err_out:
 
 static void adma_port_stop(struct ata_port *ap)
 {
-        struct device *dev = ap->host_set->dev;
+        struct device *dev = ap->host->dev;
         struct adma_port_priv *pp = ap->private_data;
 
-        adma_reset_engine(ADMA_REGS(ap->host_set->mmio_base, ap->port_no));
+        adma_reset_engine(ADMA_REGS(ap->host->mmio_base, ap->port_no));
         if (pp != NULL) {
                 ap->private_data = NULL;
                 if (pp->pkt != NULL)
@@ -596,14 +596,14 @@ static void adma_port_stop(struct ata_port *ap)
         ata_port_stop(ap);
 }
 
-static void adma_host_stop(struct ata_host_set *host_set)
+static void adma_host_stop(struct ata_host *host)
 {
         unsigned int port_no;
 
         for (port_no = 0; port_no < ADMA_PORTS; ++port_no)
-                adma_reset_engine(ADMA_REGS(host_set->mmio_base, port_no));
+                adma_reset_engine(ADMA_REGS(host->mmio_base, port_no));
 
-        ata_pci_host_stop(host_set);
+        ata_pci_host_stop(host);
 }
 
 static void adma_host_init(unsigned int chip_id,
@@ -684,7 +684,7 @@ static int adma_ata_init_one(struct pci_dev *pdev,
         INIT_LIST_HEAD(&probe_ent->node);
 
         probe_ent->sht          = adma_port_info[board_idx].sht;
-        probe_ent->host_flags   = adma_port_info[board_idx].host_flags;
+        probe_ent->port_flags   = adma_port_info[board_idx].flags;
         probe_ent->pio_mask     = adma_port_info[board_idx].pio_mask;
         probe_ent->mwdma_mask   = adma_port_info[board_idx].mwdma_mask;
         probe_ent->udma_mask    = adma_port_info[board_idx].udma_mask;
@@ -722,7 +722,7 @@ err_out:
 
 static int __init adma_ata_init(void)
 {
-        return pci_module_init(&adma_ata_pci_driver);
+        return pci_register_driver(&adma_ata_pci_driver);
 }
 
 static void __exit adma_ata_exit(void)
diff --git a/drivers/scsi/sata_mv.c b/drivers/ata/sata_mv.c
index fa38a413d16b..fdce6e07ecd2 100644
--- a/drivers/scsi/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -342,7 +342,7 @@ static u32 mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in);
 static void mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val);
 static void mv_phy_reset(struct ata_port *ap);
 static void __mv_phy_reset(struct ata_port *ap, int can_sleep);
-static void mv_host_stop(struct ata_host_set *host_set);
+static void mv_host_stop(struct ata_host *host);
 static int mv_port_start(struct ata_port *ap);
 static void mv_port_stop(struct ata_port *ap);
 static void mv_qc_prep(struct ata_queued_cmd *qc);
@@ -480,35 +480,35 @@ static const struct ata_port_operations mv_iie_ops = {
 static const struct ata_port_info mv_port_info[] = {
         {  /* chip_504x */
                 .sht            = &mv_sht,
-                .host_flags     = MV_COMMON_FLAGS,
+                .flags          = MV_COMMON_FLAGS,
                 .pio_mask       = 0x1f, /* pio0-4 */
                 .udma_mask      = 0x7f, /* udma0-6 */
                 .port_ops       = &mv5_ops,
         },
         {  /* chip_508x */
                 .sht            = &mv_sht,
-                .host_flags     = (MV_COMMON_FLAGS | MV_FLAG_DUAL_HC),
+                .flags          = (MV_COMMON_FLAGS | MV_FLAG_DUAL_HC),
                 .pio_mask       = 0x1f, /* pio0-4 */
                 .udma_mask      = 0x7f, /* udma0-6 */
                 .port_ops       = &mv5_ops,
         },
         {  /* chip_5080 */
                 .sht            = &mv_sht,
-                .host_flags     = (MV_COMMON_FLAGS | MV_FLAG_DUAL_HC),
+                .flags          = (MV_COMMON_FLAGS | MV_FLAG_DUAL_HC),
                 .pio_mask       = 0x1f, /* pio0-4 */
                 .udma_mask      = 0x7f, /* udma0-6 */
                 .port_ops       = &mv5_ops,
         },
         {  /* chip_604x */
                 .sht            = &mv_sht,
-                .host_flags     = (MV_COMMON_FLAGS | MV_6XXX_FLAGS),
+                .flags          = (MV_COMMON_FLAGS | MV_6XXX_FLAGS),
                 .pio_mask       = 0x1f, /* pio0-4 */
                 .udma_mask      = 0x7f, /* udma0-6 */
                 .port_ops       = &mv6_ops,
         },
         {  /* chip_608x */
                 .sht            = &mv_sht,
-                .host_flags     = (MV_COMMON_FLAGS | MV_6XXX_FLAGS |
+                .flags          = (MV_COMMON_FLAGS | MV_6XXX_FLAGS |
                                    MV_FLAG_DUAL_HC),
                 .pio_mask       = 0x1f, /* pio0-4 */
                 .udma_mask      = 0x7f, /* udma0-6 */
@@ -516,14 +516,14 @@ static const struct ata_port_info mv_port_info[] = {
         },
         {  /* chip_6042 */
                 .sht            = &mv_sht,
-                .host_flags     = (MV_COMMON_FLAGS | MV_6XXX_FLAGS),
+                .flags          = (MV_COMMON_FLAGS | MV_6XXX_FLAGS),
                 .pio_mask       = 0x1f, /* pio0-4 */
                 .udma_mask      = 0x7f, /* udma0-6 */
                 .port_ops       = &mv_iie_ops,
         },
         {  /* chip_7042 */
                 .sht            = &mv_sht,
-                .host_flags     = (MV_COMMON_FLAGS | MV_6XXX_FLAGS |
+                .flags          = (MV_COMMON_FLAGS | MV_6XXX_FLAGS |
                                    MV_FLAG_DUAL_HC),
                 .pio_mask       = 0x1f, /* pio0-4 */
                 .udma_mask      = 0x7f, /* udma0-6 */
@@ -618,12 +618,12 @@ static inline void __iomem *mv_port_base(void __iomem *base, unsigned int port)
 
 static inline void __iomem *mv_ap_base(struct ata_port *ap)
 {
-        return mv_port_base(ap->host_set->mmio_base, ap->port_no);
+        return mv_port_base(ap->host->mmio_base, ap->port_no);
 }
 
-static inline int mv_get_hc_count(unsigned long host_flags)
+static inline int mv_get_hc_count(unsigned long port_flags)
 {
-        return ((host_flags & MV_FLAG_DUAL_HC) ? 2 : 1);
+        return ((port_flags & MV_FLAG_DUAL_HC) ? 2 : 1);
 }
 
 static void mv_irq_clear(struct ata_port *ap)
@@ -809,7 +809,7 @@ static void mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val)
 
 /**
  *      mv_host_stop - Host specific cleanup/stop routine.
- *      @host_set: host data structure
+ *      @host: host data structure
  *
  *      Disable ints, cleanup host memory, call general purpose
  *      host_stop.
@@ -817,10 +817,10 @@ static void mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val)
  *      LOCKING:
  *      Inherited from caller.
  */
-static void mv_host_stop(struct ata_host_set *host_set)
+static void mv_host_stop(struct ata_host *host)
 {
-        struct mv_host_priv *hpriv = host_set->private_data;
-        struct pci_dev *pdev = to_pci_dev(host_set->dev);
+        struct mv_host_priv *hpriv = host->private_data;
+        struct pci_dev *pdev = to_pci_dev(host->dev);
 
         if (hpriv->hp_flags & MV_HP_FLAG_MSI) {
                 pci_disable_msi(pdev);
@@ -828,7 +828,7 @@ static void mv_host_stop(struct ata_host_set *host_set)
                 pci_intx(pdev, 0);
         }
         kfree(hpriv);
-        ata_host_stop(host_set);
+        ata_host_stop(host);
 }
 
 static inline void mv_priv_free(struct mv_port_priv *pp, struct device *dev)
@@ -875,8 +875,8 @@ static void mv_edma_cfg(struct mv_host_priv *hpriv, void __iomem *port_mmio)
  */
 static int mv_port_start(struct ata_port *ap)
 {
-        struct device *dev = ap->host_set->dev;
-        struct mv_host_priv *hpriv = ap->host_set->private_data;
+        struct device *dev = ap->host->dev;
+        struct mv_host_priv *hpriv = ap->host->private_data;
         struct mv_port_priv *pp;
         void __iomem *port_mmio = mv_ap_base(ap);
         void *mem;
@@ -965,17 +965,17 @@ err_out:
  *      Stop DMA, cleanup port memory.
  *
  *      LOCKING:
- *      This routine uses the host_set lock to protect the DMA stop.
+ *      This routine uses the host lock to protect the DMA stop.
  */
 static void mv_port_stop(struct ata_port *ap)
 {
-        struct device *dev = ap->host_set->dev;
+        struct device *dev = ap->host->dev;
         struct mv_port_priv *pp = ap->private_data;
         unsigned long flags;
 
-        spin_lock_irqsave(&ap->host_set->lock, flags);
+        spin_lock_irqsave(&ap->host->lock, flags);
         mv_stop_dma(ap);
-        spin_unlock_irqrestore(&ap->host_set->lock, flags);
+        spin_unlock_irqrestore(&ap->host->lock, flags);
 
         ap->private_data = NULL;
         ata_pad_free(ap, dev);
@@ -1330,7 +1330,7 @@ static void mv_err_intr(struct ata_port *ap, int reset_allowed)
 
 /**
  *      mv_host_intr - Handle all interrupts on the given host controller
- *      @host_set: host specific structure
+ *      @host: host specific structure
  *      @relevant: port error bits relevant to this host controller
  *      @hc: which host controller we're to look at
  *
@@ -1344,10 +1344,9 @@ static void mv_err_intr(struct ata_port *ap, int reset_allowed)
  *      LOCKING:
  *      Inherited from caller.
  */
-static void mv_host_intr(struct ata_host_set *host_set, u32 relevant,
-                         unsigned int hc)
+static void mv_host_intr(struct ata_host *host, u32 relevant, unsigned int hc)
 {
-        void __iomem *mmio = host_set->mmio_base;
+        void __iomem *mmio = host->mmio_base;
         void __iomem *hc_mmio = mv_hc_base(mmio, hc);
         struct ata_queued_cmd *qc;
         u32 hc_irq_cause;
@@ -1371,7 +1370,7 @@ static void mv_host_intr(struct ata_host_set *host_set, u32 relevant,
 
         for (port = port0; port < port0 + MV_PORTS_PER_HC; port++) {
                 u8 ata_status = 0;
-                struct ata_port *ap = host_set->ports[port];
+                struct ata_port *ap = host->ports[port];
                 struct mv_port_priv *pp = ap->private_data;
 
                 hard_port = mv_hardport_from_port(port); /* range 0..3 */
@@ -1444,15 +1443,15 @@ static void mv_host_intr(struct ata_host_set *host_set, u32 relevant,
  *      reported here.
  *
  *      LOCKING:
- *      This routine holds the host_set lock while processing pending
+ *      This routine holds the host lock while processing pending
  *      interrupts.
  */
 static irqreturn_t mv_interrupt(int irq, void *dev_instance,
                                 struct pt_regs *regs)
 {
-        struct ata_host_set *host_set = dev_instance;
+        struct ata_host *host = dev_instance;
         unsigned int hc, handled = 0, n_hcs;
-        void __iomem *mmio = host_set->mmio_base;
+        void __iomem *mmio = host->mmio_base;
         struct mv_host_priv *hpriv;
         u32 irq_stat;
 
@@ -1465,18 +1464,18 @@ static irqreturn_t mv_interrupt(int irq, void *dev_instance,
                 return IRQ_NONE;
         }
 
-        n_hcs = mv_get_hc_count(host_set->ports[0]->flags);
-        spin_lock(&host_set->lock);
+        n_hcs = mv_get_hc_count(host->ports[0]->flags);
+        spin_lock(&host->lock);
 
         for (hc = 0; hc < n_hcs; hc++) {
                 u32 relevant = irq_stat & (HC0_IRQ_PEND << (hc * HC_SHIFT));
                 if (relevant) {
-                        mv_host_intr(host_set, relevant, hc);
+                        mv_host_intr(host, relevant, hc);
                         handled++;
                 }
         }
 
-        hpriv = host_set->private_data;
+        hpriv = host->private_data;
         if (IS_60XX(hpriv)) {
                 /* deal with the interrupt coalescing bits */
                 if (irq_stat & (TRAN_LO_DONE | TRAN_HI_DONE | PORTS_0_7_COAL_DONE)) {
@@ -1491,12 +1490,12 @@ static irqreturn_t mv_interrupt(int irq, void *dev_instance,
                        readl(mmio + PCI_IRQ_CAUSE_OFS));
 
                 DPRINTK("All regs @ PCI error\n");
-                mv_dump_all_regs(mmio, -1, to_pci_dev(host_set->dev));
+                mv_dump_all_regs(mmio, -1, to_pci_dev(host->dev));
 
                 writelfl(0, mmio + PCI_IRQ_CAUSE_OFS);
                 handled++;
         }
-        spin_unlock(&host_set->lock);
+        spin_unlock(&host->lock);
 
         return IRQ_RETVAL(handled);
 }
@@ -1528,7 +1527,7 @@ static unsigned int mv5_scr_offset(unsigned int sc_reg_in)
 
 static u32 mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in)
 {
-        void __iomem *mmio = mv5_phy_base(ap->host_set->mmio_base, ap->port_no);
+        void __iomem *mmio = mv5_phy_base(ap->host->mmio_base, ap->port_no);
         unsigned int ofs = mv5_scr_offset(sc_reg_in);
 
         if (ofs != 0xffffffffU)
@@ -1539,7 +1538,7 @@ static u32 mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in)
 
 static void mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val)
 {
-        void __iomem *mmio = mv5_phy_base(ap->host_set->mmio_base, ap->port_no);
+        void __iomem *mmio = mv5_phy_base(ap->host->mmio_base, ap->port_no);
         unsigned int ofs = mv5_scr_offset(sc_reg_in);
 
         if (ofs != 0xffffffffU)
@@ -1904,8 +1903,8 @@ static void mv_channel_reset(struct mv_host_priv *hpriv, void __iomem *mmio,
 
 static void mv_stop_and_reset(struct ata_port *ap)
 {
-        struct mv_host_priv *hpriv = ap->host_set->private_data;
-        void __iomem *mmio = ap->host_set->mmio_base;
+        struct mv_host_priv *hpriv = ap->host->private_data;
+        void __iomem *mmio = ap->host->mmio_base;
 
         mv_stop_dma(ap);
 
@@ -1936,7 +1935,7 @@ static inline void __msleep(unsigned int msec, int can_sleep)
 static void __mv_phy_reset(struct ata_port *ap, int can_sleep)
 {
         struct mv_port_priv *pp = ap->private_data;
-        struct mv_host_priv *hpriv = ap->host_set->private_data;
+        struct mv_host_priv *hpriv = ap->host->private_data;
         void __iomem *port_mmio = mv_ap_base(ap);
         struct ata_taskfile tf;
         struct ata_device *dev = &ap->device[0];
@@ -2034,7 +2033,7 @@ static void mv_phy_reset(struct ata_port *ap)
  *      chip/bus, fail the command, and move on.
  *
  *      LOCKING:
- *      This routine holds the host_set lock while failing the command.
+ *      This routine holds the host lock while failing the command.
  */
 static void mv_eng_timeout(struct ata_port *ap)
 {
@@ -2043,18 +2042,17 @@ static void mv_eng_timeout(struct ata_port *ap)
 
         ata_port_printk(ap, KERN_ERR, "Entering mv_eng_timeout\n");
         DPRINTK("All regs @ start of eng_timeout\n");
-        mv_dump_all_regs(ap->host_set->mmio_base, ap->port_no,
-                         to_pci_dev(ap->host_set->dev));
+        mv_dump_all_regs(ap->host->mmio_base, ap->port_no,
+                         to_pci_dev(ap->host->dev));
 
         qc = ata_qc_from_tag(ap, ap->active_tag);
         printk(KERN_ERR "mmio_base %p ap %p qc %p scsi_cmnd %p &cmnd %p\n",
-               ap->host_set->mmio_base, ap, qc, qc->scsicmd,
-               &qc->scsicmd->cmnd);
+               ap->host->mmio_base, ap, qc, qc->scsicmd, &qc->scsicmd->cmnd);
 
-        spin_lock_irqsave(&ap->host_set->lock, flags);
+        spin_lock_irqsave(&ap->host->lock, flags);
         mv_err_intr(ap, 0);
         mv_stop_and_reset(ap);
-        spin_unlock_irqrestore(&ap->host_set->lock, flags);
+        spin_unlock_irqrestore(&ap->host->lock, flags);
 
         WARN_ON(!(qc->flags & ATA_QCFLAG_ACTIVE));
         if (qc->flags & ATA_QCFLAG_ACTIVE) {
@@ -2235,7 +2233,7 @@ static int mv_init_host(struct pci_dev *pdev, struct ata_probe_ent *probe_ent,
         if (rc)
                 goto done;
 
-        n_hc = mv_get_hc_count(probe_ent->host_flags);
+        n_hc = mv_get_hc_count(probe_ent->port_flags);
         probe_ent->n_ports = MV_PORTS_PER_HC * n_hc;
 
         for (port = 0; port < probe_ent->n_ports; port++)
@@ -2388,7 +2386,7 @@ static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
         memset(hpriv, 0, sizeof(*hpriv));
 
         probe_ent->sht = mv_port_info[board_idx].sht;
-        probe_ent->host_flags = mv_port_info[board_idx].host_flags;
+        probe_ent->port_flags = mv_port_info[board_idx].flags;
         probe_ent->pio_mask = mv_port_info[board_idx].pio_mask;
         probe_ent->udma_mask = mv_port_info[board_idx].udma_mask;
         probe_ent->port_ops = mv_port_info[board_idx].port_ops;
@@ -2446,7 +2444,7 @@ err_out:
 
 static int __init mv_init(void)
 {
-        return pci_module_init(&mv_pci_driver);
+        return pci_register_driver(&mv_pci_driver);
 }
 
 static void __exit mv_exit(void)
diff --git a/drivers/scsi/sata_nv.c b/drivers/ata/sata_nv.c
index 56da25581f31..27c22feebf30 100644
--- a/drivers/scsi/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -81,7 +81,7 @@ enum {
 };
 
 static int nv_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
-static void nv_ck804_host_stop(struct ata_host_set *host_set);
+static void nv_ck804_host_stop(struct ata_host *host);
 static irqreturn_t nv_generic_interrupt(int irq, void *dev_instance,
                                         struct pt_regs *regs);
 static irqreturn_t nv_nf2_interrupt(int irq, void *dev_instance,
@@ -257,7 +257,7 @@ static struct ata_port_info nv_port_info[] = {
         /* generic */
         {
                 .sht            = &nv_sht,
-                .host_flags     = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
+                .flags          = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
                 .pio_mask       = NV_PIO_MASK,
                 .mwdma_mask     = NV_MWDMA_MASK,
                 .udma_mask      = NV_UDMA_MASK,
@@ -266,7 +266,7 @@ static struct ata_port_info nv_port_info[] = {
         /* nforce2/3 */
         {
                 .sht            = &nv_sht,
-                .host_flags     = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
+                .flags          = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
                 .pio_mask       = NV_PIO_MASK,
                 .mwdma_mask     = NV_MWDMA_MASK,
                 .udma_mask      = NV_UDMA_MASK,
@@ -275,7 +275,7 @@ static struct ata_port_info nv_port_info[] = {
         /* ck804 */
         {
                 .sht            = &nv_sht,
-                .host_flags     = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
+                .flags          = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
                 .pio_mask       = NV_PIO_MASK,
                 .mwdma_mask     = NV_MWDMA_MASK,
                 .udma_mask      = NV_UDMA_MASK,
@@ -292,17 +292,17 @@ MODULE_VERSION(DRV_VERSION);
 static irqreturn_t nv_generic_interrupt(int irq, void *dev_instance,
                                         struct pt_regs *regs)
 {
-        struct ata_host_set *host_set = dev_instance;
+        struct ata_host *host = dev_instance;
         unsigned int i;
         unsigned int handled = 0;
         unsigned long flags;
 
-        spin_lock_irqsave(&host_set->lock, flags);
+        spin_lock_irqsave(&host->lock, flags);
 
-        for (i = 0; i < host_set->n_ports; i++) {
+        for (i = 0; i < host->n_ports; i++) {
                 struct ata_port *ap;
 
-                ap = host_set->ports[i];
+                ap = host->ports[i];
                 if (ap &&
                     !(ap->flags & ATA_FLAG_DISABLED)) {
                         struct ata_queued_cmd *qc;
@@ -318,7 +318,7 @@ static irqreturn_t nv_generic_interrupt(int irq, void *dev_instance,
 
         }
 
-        spin_unlock_irqrestore(&host_set->lock, flags);
+        spin_unlock_irqrestore(&host->lock, flags);
 
         return IRQ_RETVAL(handled);
 }
@@ -354,12 +354,12 @@ static int nv_host_intr(struct ata_port *ap, u8 irq_stat)
         return 1;
 }
 
-static irqreturn_t nv_do_interrupt(struct ata_host_set *host_set, u8 irq_stat)
+static irqreturn_t nv_do_interrupt(struct ata_host *host, u8 irq_stat)
 {
         int i, handled = 0;
 
-        for (i = 0; i < host_set->n_ports; i++) {
-                struct ata_port *ap = host_set->ports[i];
+        for (i = 0; i < host->n_ports; i++) {
+                struct ata_port *ap = host->ports[i];
 
                 if (ap && !(ap->flags & ATA_FLAG_DISABLED))
                         handled += nv_host_intr(ap, irq_stat);
@@ -373,14 +373,14 @@ static irqreturn_t nv_do_interrupt(struct ata_host_set *host_set, u8 irq_stat)
 static irqreturn_t nv_nf2_interrupt(int irq, void *dev_instance,
                                     struct pt_regs *regs)
 {
-        struct ata_host_set *host_set = dev_instance;
+        struct ata_host *host = dev_instance;
         u8 irq_stat;
         irqreturn_t ret;
 
-        spin_lock(&host_set->lock);
-        irq_stat = inb(host_set->ports[0]->ioaddr.scr_addr + NV_INT_STATUS);
-        ret = nv_do_interrupt(host_set, irq_stat);
-        spin_unlock(&host_set->lock);
+        spin_lock(&host->lock);
+        irq_stat = inb(host->ports[0]->ioaddr.scr_addr + NV_INT_STATUS);
+        ret = nv_do_interrupt(host, irq_stat);
+        spin_unlock(&host->lock);
 
         return ret;
 }
@@ -388,14 +388,14 @@ static irqreturn_t nv_nf2_interrupt(int irq, void *dev_instance,
 static irqreturn_t nv_ck804_interrupt(int irq, void *dev_instance,
                                       struct pt_regs *regs)
 {
-        struct ata_host_set *host_set = dev_instance;
+        struct ata_host *host = dev_instance;
         u8 irq_stat;
         irqreturn_t ret;
 
-        spin_lock(&host_set->lock);
-        irq_stat = readb(host_set->mmio_base + NV_INT_STATUS_CK804);
-        ret = nv_do_interrupt(host_set, irq_stat);
-        spin_unlock(&host_set->lock);
+        spin_lock(&host->lock);
+        irq_stat = readb(host->mmio_base + NV_INT_STATUS_CK804);
+        ret = nv_do_interrupt(host, irq_stat);
+        spin_unlock(&host->lock);
 
         return ret;
 }
@@ -418,7 +418,7 @@ static void nv_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
 
 static void nv_nf2_freeze(struct ata_port *ap)
 {
-        unsigned long scr_addr = ap->host_set->ports[0]->ioaddr.scr_addr;
+        unsigned long scr_addr = ap->host->ports[0]->ioaddr.scr_addr;
         int shift = ap->port_no * NV_INT_PORT_SHIFT;
         u8 mask;
 
@@ -429,7 +429,7 @@ static void nv_nf2_freeze(struct ata_port *ap)
 
 static void nv_nf2_thaw(struct ata_port *ap)
 {
-        unsigned long scr_addr = ap->host_set->ports[0]->ioaddr.scr_addr;
+        unsigned long scr_addr = ap->host->ports[0]->ioaddr.scr_addr;
         int shift = ap->port_no * NV_INT_PORT_SHIFT;
         u8 mask;
 
@@ -442,7 +442,7 @@ static void nv_nf2_thaw(struct ata_port *ap)
 
 static void nv_ck804_freeze(struct ata_port *ap)
 {
-        void __iomem *mmio_base = ap->host_set->mmio_base;
+        void __iomem *mmio_base = ap->host->mmio_base;
         int shift = ap->port_no * NV_INT_PORT_SHIFT;
         u8 mask;
 
@@ -453,7 +453,7 @@ static void nv_ck804_freeze(struct ata_port *ap)
 
 static void nv_ck804_thaw(struct ata_port *ap)
 {
-        void __iomem *mmio_base = ap->host_set->mmio_base;
+        void __iomem *mmio_base = ap->host->mmio_base;
         int shift = ap->port_no * NV_INT_PORT_SHIFT;
         u8 mask;
 
@@ -568,9 +568,9 @@ err_out:
         return rc;
 }
 
-static void nv_ck804_host_stop(struct ata_host_set *host_set)
+static void nv_ck804_host_stop(struct ata_host *host)
 {
-        struct pci_dev *pdev = to_pci_dev(host_set->dev);
+        struct pci_dev *pdev = to_pci_dev(host->dev);
         u8 regval;
 
         /* disable SATA space for CK804 */
@@ -578,12 +578,12 @@ static void nv_ck804_host_stop(struct ata_host_set *host_set)
         regval &= ~NV_MCP_SATA_CFG_20_SATA_SPACE_EN;
         pci_write_config_byte(pdev, NV_MCP_SATA_CFG_20, regval);
 
-        ata_pci_host_stop(host_set);
+        ata_pci_host_stop(host);
 }
 
 static int __init nv_init(void)
 {
-        return pci_module_init(&nv_pci_driver);
+        return pci_register_driver(&nv_pci_driver);
 }
 
 static void __exit nv_exit(void)
diff --git a/drivers/scsi/sata_promise.c b/drivers/ata/sata_promise.c
index 4776f4e55839..d627812ea73d 100644
--- a/drivers/scsi/sata_promise.c
+++ b/drivers/ata/sata_promise.c
@@ -104,7 +104,7 @@ static void pdc_tf_load_mmio(struct ata_port *ap, const struct ata_taskfile *tf)
 static void pdc_exec_command_mmio(struct ata_port *ap, const struct ata_taskfile *tf);
 static void pdc_irq_clear(struct ata_port *ap);
 static unsigned int pdc_qc_issue_prot(struct ata_queued_cmd *qc);
-static void pdc_host_stop(struct ata_host_set *host_set);
+static void pdc_host_stop(struct ata_host *host);
 
 
 static struct scsi_host_template pdc_ata_sht = {
@@ -175,7 +175,7 @@ static const struct ata_port_info pdc_port_info[] = {
         /* board_2037x */
         {
                 .sht            = &pdc_ata_sht,
-                .host_flags     = PDC_COMMON_FLAGS | ATA_FLAG_SATA,
+                .flags          = PDC_COMMON_FLAGS | ATA_FLAG_SATA,
                 .pio_mask       = 0x1f, /* pio0-4 */
                 .mwdma_mask     = 0x07, /* mwdma0-2 */
                 .udma_mask      = 0x7f, /* udma0-6 ; FIXME */
@@ -185,7 +185,7 @@ static const struct ata_port_info pdc_port_info[] = {
         /* board_20319 */
         {
                 .sht            = &pdc_ata_sht,
-                .host_flags     = PDC_COMMON_FLAGS | ATA_FLAG_SATA,
+                .flags          = PDC_COMMON_FLAGS | ATA_FLAG_SATA,
                 .pio_mask       = 0x1f, /* pio0-4 */
                 .mwdma_mask     = 0x07, /* mwdma0-2 */
                 .udma_mask      = 0x7f, /* udma0-6 ; FIXME */
@@ -195,7 +195,7 @@ static const struct ata_port_info pdc_port_info[] = {
         /* board_20619 */
         {
                 .sht            = &pdc_ata_sht,
-                .host_flags     = PDC_COMMON_FLAGS | ATA_FLAG_SLAVE_POSS,
+                .flags          = PDC_COMMON_FLAGS | ATA_FLAG_SLAVE_POSS,
                 .pio_mask       = 0x1f, /* pio0-4 */
                 .mwdma_mask     = 0x07, /* mwdma0-2 */
                 .udma_mask      = 0x7f, /* udma0-6 ; FIXME */
@@ -205,7 +205,7 @@ static const struct ata_port_info pdc_port_info[] = {
         /* board_20771 */
         {
                 .sht            = &pdc_ata_sht,
-                .host_flags     = PDC_COMMON_FLAGS | ATA_FLAG_SATA,
+                .flags          = PDC_COMMON_FLAGS | ATA_FLAG_SATA,
                 .pio_mask       = 0x1f, /* pio0-4 */
                 .mwdma_mask     = 0x07, /* mwdma0-2 */
                 .udma_mask      = 0x7f, /* udma0-6 ; FIXME */
@@ -215,7 +215,7 @@ static const struct ata_port_info pdc_port_info[] = {
         /* board_2057x */
         {
                 .sht            = &pdc_ata_sht,
-                .host_flags     = PDC_COMMON_FLAGS | ATA_FLAG_SATA,
+                .flags          = PDC_COMMON_FLAGS | ATA_FLAG_SATA,
                 .pio_mask       = 0x1f, /* pio0-4 */
                 .mwdma_mask     = 0x07, /* mwdma0-2 */
                 .udma_mask      = 0x7f, /* udma0-6 ; FIXME */
@@ -225,7 +225,7 @@ static const struct ata_port_info pdc_port_info[] = {
         /* board_40518 */
         {
                 .sht            = &pdc_ata_sht,
-                .host_flags     = PDC_COMMON_FLAGS | ATA_FLAG_SATA,
+                .flags          = PDC_COMMON_FLAGS | ATA_FLAG_SATA,
                 .pio_mask       = 0x1f, /* pio0-4 */
                 .mwdma_mask     = 0x07, /* mwdma0-2 */
                 .udma_mask      = 0x7f, /* udma0-6 ; FIXME */
@@ -292,7 +292,7 @@ static struct pci_driver pdc_ata_pci_driver = {
 
 static int pdc_port_start(struct ata_port *ap)
 {
-        struct device *dev = ap->host_set->dev;
+        struct device *dev = ap->host->dev;
         struct pdc_port_priv *pp;
         int rc;
 
@@ -326,7 +326,7 @@ err_out:
 
 static void pdc_port_stop(struct ata_port *ap)
 {
-        struct device *dev = ap->host_set->dev;
+        struct device *dev = ap->host->dev;
         struct pdc_port_priv *pp = ap->private_data;
 
         ap->private_data = NULL;
@@ -336,11 +336,11 @@ static void pdc_port_stop(struct ata_port *ap)
 }
 
 
-static void pdc_host_stop(struct ata_host_set *host_set)
+static void pdc_host_stop(struct ata_host *host)
 {
-        struct pdc_host_priv *hp = host_set->private_data;
+        struct pdc_host_priv *hp = host->private_data;
 
-        ata_pci_host_stop(host_set);
+        ata_pci_host_stop(host);
 
         kfree(hp);
 }
@@ -443,14 +443,14 @@ static void pdc_qc_prep(struct ata_queued_cmd *qc)
 
 static void pdc_eng_timeout(struct ata_port *ap)
 {
-        struct ata_host_set *host_set = ap->host_set;
+        struct ata_host *host = ap->host;
         u8 drv_stat;
         struct ata_queued_cmd *qc;
         unsigned long flags;
 
         DPRINTK("ENTER\n");
 
-        spin_lock_irqsave(&host_set->lock, flags);
+        spin_lock_irqsave(&host->lock, flags);
 
         qc = ata_qc_from_tag(ap, ap->active_tag);
 
@@ -473,7 +473,7 @@ static void pdc_eng_timeout(struct ata_port *ap)
                 break;
         }
 
-        spin_unlock_irqrestore(&host_set->lock, flags);
+        spin_unlock_irqrestore(&host->lock, flags);
         ata_eh_qc_complete(qc);
         DPRINTK("EXIT\n");
 }
@@ -509,15 +509,15 @@ static inline unsigned int pdc_host_intr( struct ata_port *ap,
 
 static void pdc_irq_clear(struct ata_port *ap)
 {
-        struct ata_host_set *host_set = ap->host_set;
-        void __iomem *mmio = host_set->mmio_base;
+        struct ata_host *host = ap->host;
+        void __iomem *mmio = host->mmio_base;
 
         readl(mmio + PDC_INT_SEQMASK);
 }
 
 static irqreturn_t pdc_interrupt (int irq, void *dev_instance, struct pt_regs *regs)
 {
-        struct ata_host_set *host_set = dev_instance;
+        struct ata_host *host = dev_instance;
         struct ata_port *ap;
         u32 mask = 0;
         unsigned int i, tmp;
@@ -526,12 +526,12 @@ static irqreturn_t pdc_interrupt (int irq, void *dev_instance, struct pt_regs *r
 
         VPRINTK("ENTER\n");
 
-        if (!host_set || !host_set->mmio_base) {
+        if (!host || !host->mmio_base) {
                 VPRINTK("QUICK EXIT\n");
                 return IRQ_NONE;
         }
 
-        mmio_base = host_set->mmio_base;
+        mmio_base = host->mmio_base;
 
         /* reading should also clear interrupts */
         mask = readl(mmio_base + PDC_INT_SEQMASK);
@@ -541,7 +541,7 @@ static irqreturn_t pdc_interrupt (int irq, void *dev_instance, struct pt_regs *r
                 return IRQ_NONE;
         }
 
-        spin_lock(&host_set->lock);
+        spin_lock(&host->lock);
 
         mask &= 0xffff;         /* only 16 tags possible */
         if (!mask) {
@@ -551,9 +551,9 @@ static irqreturn_t pdc_interrupt (int irq, void *dev_instance, struct pt_regs *r
 
         writel(mask, mmio_base + PDC_INT_SEQMASK);
 
-        for (i = 0; i < host_set->n_ports; i++) {
+        for (i = 0; i < host->n_ports; i++) {
                 VPRINTK("port %u\n", i);
-                ap = host_set->ports[i];
+                ap = host->ports[i];
                 tmp = mask & (1 << (i + 1));
                 if (tmp && ap &&
                     !(ap->flags & ATA_FLAG_DISABLED)) {
@@ -568,7 +568,7 @@ static irqreturn_t pdc_interrupt (int irq, void *dev_instance, struct pt_regs *r
         VPRINTK("EXIT\n");
 
 done_irq:
-        spin_unlock(&host_set->lock);
+        spin_unlock(&host->lock);
         return IRQ_RETVAL(handled);
 }
 
@@ -581,8 +581,8 @@ static inline void pdc_packet_start(struct ata_queued_cmd *qc)
 
         VPRINTK("ENTER, ap %p\n", ap);
 
-        writel(0x00000001, ap->host_set->mmio_base + (seq * 4));
-        readl(ap->host_set->mmio_base + (seq * 4));     /* flush */
+        writel(0x00000001, ap->host->mmio_base + (seq * 4));
+        readl(ap->host->mmio_base + (seq * 4)); /* flush */
 
         pp->pkt[2] = seq;
         wmb();                  /* flush PRD, pkt writes */
@@ -743,7 +743,7 @@ static int pdc_ata_init_one (struct pci_dev *pdev, const struct pci_device_id *e
         probe_ent->private_data = hp;
 
         probe_ent->sht          = pdc_port_info[board_idx].sht;
-        probe_ent->host_flags   = pdc_port_info[board_idx].host_flags;
+        probe_ent->port_flags   = pdc_port_info[board_idx].flags;
         probe_ent->pio_mask     = pdc_port_info[board_idx].pio_mask;
         probe_ent->mwdma_mask   = pdc_port_info[board_idx].mwdma_mask;
         probe_ent->udma_mask    = pdc_port_info[board_idx].udma_mask;
@@ -824,7 +824,7 @@ err_out:
 
 static int __init pdc_ata_init(void)
 {
-        return pci_module_init(&pdc_ata_pci_driver);
+        return pci_register_driver(&pdc_ata_pci_driver);
 }
 
 
diff --git a/drivers/scsi/sata_promise.h b/drivers/ata/sata_promise.h
index 6ee5e190262d..6ee5e190262d 100644
--- a/drivers/scsi/sata_promise.h
+++ b/drivers/ata/sata_promise.h
diff --git a/drivers/scsi/sata_qstor.c b/drivers/ata/sata_qstor.c
index d374c1db0cf3..fa29dfe2a7b5 100644
--- a/drivers/scsi/sata_qstor.c
+++ b/drivers/ata/sata_qstor.c
@@ -116,7 +116,7 @@ static void qs_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
 static int qs_ata_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
 static irqreturn_t qs_intr (int irq, void *dev_instance, struct pt_regs *regs);
 static int qs_port_start(struct ata_port *ap);
-static void qs_host_stop(struct ata_host_set *host_set);
+static void qs_host_stop(struct ata_host *host);
 static void qs_port_stop(struct ata_port *ap);
 static void qs_phy_reset(struct ata_port *ap);
 static void qs_qc_prep(struct ata_queued_cmd *qc);
@@ -174,7 +174,7 @@ static const struct ata_port_info qs_port_info[] = {
         /* board_2068_idx */
         {
                 .sht            = &qs_ata_sht,
-                .host_flags     = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+                .flags          = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
                                   ATA_FLAG_SATA_RESET |
                                   //FIXME ATA_FLAG_SRST |
                                   ATA_FLAG_MMIO | ATA_FLAG_PIO_POLLING,
@@ -220,7 +220,7 @@ static void qs_irq_clear(struct ata_port *ap)
 
 static inline void qs_enter_reg_mode(struct ata_port *ap)
 {
-        u8 __iomem *chan = ap->host_set->mmio_base + (ap->port_no * 0x4000);
+        u8 __iomem *chan = ap->host->mmio_base + (ap->port_no * 0x4000);
 
         writeb(QS_CTR0_REG, chan + QS_CCT_CTR0);
         readb(chan + QS_CCT_CTR0);        /* flush */
@@ -228,7 +228,7 @@ static inline void qs_enter_reg_mode(struct ata_port *ap)
 
 static inline void qs_reset_channel_logic(struct ata_port *ap)
 {
-        u8 __iomem *chan = ap->host_set->mmio_base + (ap->port_no * 0x4000);
+        u8 __iomem *chan = ap->host->mmio_base + (ap->port_no * 0x4000);
 
         writeb(QS_CTR1_RCHN, chan + QS_CCT_CTR1);
         readb(chan + QS_CCT_CTR0);        /* flush */
@@ -342,7 +342,7 @@ static void qs_qc_prep(struct ata_queued_cmd *qc)
 static inline void qs_packet_start(struct ata_queued_cmd *qc)
 {
         struct ata_port *ap = qc->ap;
-        u8 __iomem *chan = ap->host_set->mmio_base + (ap->port_no * 0x4000);
+        u8 __iomem *chan = ap->host->mmio_base + (ap->port_no * 0x4000);
 
         VPRINTK("ENTER, ap %p\n", ap);
 
@@ -375,11 +375,11 @@ static unsigned int qs_qc_issue(struct ata_queued_cmd *qc)
         return ata_qc_issue_prot(qc);
 }
 
-static inline unsigned int qs_intr_pkt(struct ata_host_set *host_set)
+static inline unsigned int qs_intr_pkt(struct ata_host *host)
 {
         unsigned int handled = 0;
         u8 sFFE;
-        u8 __iomem *mmio_base = host_set->mmio_base;
+        u8 __iomem *mmio_base = host->mmio_base;
 
         do {
                 u32 sff0 = readl(mmio_base + QS_HST_SFF);
@@ -391,7 +391,7 @@ static inline unsigned int qs_intr_pkt(struct ata_host_set *host_set)
                         u8 sDST = sff0 >> 16;   /* dev status */
                         u8 sHST = sff1 & 0x3f;  /* host status */
                         unsigned int port_no = (sff1 >> 8) & 0x03;
-                        struct ata_port *ap = host_set->ports[port_no];
+                        struct ata_port *ap = host->ports[port_no];
 
                         DPRINTK("SFF=%08x%08x: sCHAN=%u sHST=%d sDST=%02x\n",
                                         sff1, sff0, port_no, sHST, sDST);
@@ -421,13 +421,13 @@ static inline unsigned int qs_intr_pkt(struct ata_host_set *host_set)
         return handled;
 }
 
-static inline unsigned int qs_intr_mmio(struct ata_host_set *host_set)
+static inline unsigned int qs_intr_mmio(struct ata_host *host)
 {
         unsigned int handled = 0, port_no;
 
-        for (port_no = 0; port_no < host_set->n_ports; ++port_no) {
+        for (port_no = 0; port_no < host->n_ports; ++port_no) {
                 struct ata_port *ap;
-                ap = host_set->ports[port_no];
+                ap = host->ports[port_no];
                 if (ap &&
                     !(ap->flags & ATA_FLAG_DISABLED)) {
                         struct ata_queued_cmd *qc;
@@ -457,14 +457,14 @@ static inline unsigned int qs_intr_mmio(struct ata_host_set *host_set)
 
 static irqreturn_t qs_intr(int irq, void *dev_instance, struct pt_regs *regs)
 {
-        struct ata_host_set *host_set = dev_instance;
+        struct ata_host *host = dev_instance;
         unsigned int handled = 0;
 
         VPRINTK("ENTER\n");
 
-        spin_lock(&host_set->lock);
-        handled  = qs_intr_pkt(host_set) | qs_intr_mmio(host_set);
-        spin_unlock(&host_set->lock);
+        spin_lock(&host->lock);
+        handled  = qs_intr_pkt(host) | qs_intr_mmio(host);
+        spin_unlock(&host->lock);
 
         VPRINTK("EXIT\n");
 
@@ -491,9 +491,9 @@ static void qs_ata_setup_port(struct ata_ioports *port, unsigned long base)
 
 static int qs_port_start(struct ata_port *ap)
 {
-        struct device *dev = ap->host_set->dev;
+        struct device *dev = ap->host->dev;
         struct qs_port_priv *pp;
-        void __iomem *mmio_base = ap->host_set->mmio_base;
+        void __iomem *mmio_base = ap->host->mmio_base;
         void __iomem *chan = mmio_base + (ap->port_no * 0x4000);
         u64 addr;
         int rc;
@@ -530,7 +530,7 @@ err_out:
 
 static void qs_port_stop(struct ata_port *ap)
 {
-        struct device *dev = ap->host_set->dev;
+        struct device *dev = ap->host->dev;
         struct qs_port_priv *pp = ap->private_data;
 
         if (pp != NULL) {
@@ -543,10 +543,10 @@ static void qs_port_stop(struct ata_port *ap)
         ata_port_stop(ap);
 }
 
-static void qs_host_stop(struct ata_host_set *host_set)
+static void qs_host_stop(struct ata_host *host)
 {
-        void __iomem *mmio_base = host_set->mmio_base;
-        struct pci_dev *pdev = to_pci_dev(host_set->dev);
+        void __iomem *mmio_base = host->mmio_base;
+        struct pci_dev *pdev = to_pci_dev(host->dev);
 
         writeb(0, mmio_base + QS_HCT_CTRL); /* disable host interrupts */
         writeb(QS_CNFG3_GSRST, mmio_base + QS_HCF_CNFG3); /* global reset */
@@ -673,7 +673,7 @@ static int qs_ata_init_one(struct pci_dev *pdev,
         INIT_LIST_HEAD(&probe_ent->node);
 
         probe_ent->sht          = qs_port_info[board_idx].sht;
-        probe_ent->host_flags   = qs_port_info[board_idx].host_flags;
+        probe_ent->port_flags   = qs_port_info[board_idx].flags;
         probe_ent->pio_mask     = qs_port_info[board_idx].pio_mask;
         probe_ent->mwdma_mask   = qs_port_info[board_idx].mwdma_mask;
         probe_ent->udma_mask    = qs_port_info[board_idx].udma_mask;
@@ -712,7 +712,7 @@ err_out:
 
 static int __init qs_ata_init(void)
 {
-        return pci_module_init(&qs_ata_pci_driver);
+        return pci_register_driver(&qs_ata_pci_driver);
 }
 
 static void __exit qs_ata_exit(void)
diff --git a/drivers/scsi/sata_sil.c b/drivers/ata/sata_sil.c
index d0a85073ebf7..c63dbabc0cd9 100644
--- a/drivers/scsi/sata_sil.c
+++ b/drivers/ata/sata_sil.c
@@ -56,7 +56,7 @@ enum {
         SIL_FLAG_RERR_ON_DMA_ACT = (1 << 29),
         SIL_FLAG_MOD15WRITE     = (1 << 30),
 
-        SIL_DFL_HOST_FLAGS      = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+        SIL_DFL_PORT_FLAGS      = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
                                   ATA_FLAG_MMIO | ATA_FLAG_HRST_TO_RESUME,
 
         /*
@@ -109,7 +109,9 @@ enum {
 };
 
 static int sil_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
+#ifdef CONFIG_PM
 static int sil_pci_device_resume(struct pci_dev *pdev);
+#endif
 static void sil_dev_config(struct ata_port *ap, struct ata_device *dev);
 static u32 sil_scr_read (struct ata_port *ap, unsigned int sc_reg);
 static void sil_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
@@ -141,12 +143,8 @@ static const struct sil_drivelist {
         { "ST330013AS",         SIL_QUIRK_MOD15WRITE },
         { "ST340017AS",         SIL_QUIRK_MOD15WRITE },
         { "ST360015AS",         SIL_QUIRK_MOD15WRITE },
-        { "ST380013AS",         SIL_QUIRK_MOD15WRITE },
         { "ST380023AS",         SIL_QUIRK_MOD15WRITE },
         { "ST3120023AS",        SIL_QUIRK_MOD15WRITE },
-        { "ST3160023AS",        SIL_QUIRK_MOD15WRITE },
-        { "ST3120026AS",        SIL_QUIRK_MOD15WRITE },
-        { "ST3200822AS",        SIL_QUIRK_MOD15WRITE },
         { "ST340014ASL",        SIL_QUIRK_MOD15WRITE },
         { "ST360014ASL",        SIL_QUIRK_MOD15WRITE },
         { "ST380011ASL",        SIL_QUIRK_MOD15WRITE },
@@ -161,8 +159,10 @@ static struct pci_driver sil_pci_driver = {
         .id_table               = sil_pci_tbl,
         .probe                  = sil_init_one,
         .remove                 = ata_pci_remove_one,
+#ifdef CONFIG_PM
         .suspend                = ata_pci_device_suspend,
         .resume                 = sil_pci_device_resume,
+#endif
 };
 
 static struct scsi_host_template sil_sht = {
@@ -218,7 +218,7 @@ static const struct ata_port_info sil_port_info[] = {
         /* sil_3112 */
         {
                 .sht            = &sil_sht,
-                .host_flags     = SIL_DFL_HOST_FLAGS | SIL_FLAG_MOD15WRITE,
+                .flags          = SIL_DFL_PORT_FLAGS | SIL_FLAG_MOD15WRITE,
                 .pio_mask       = 0x1f,                 /* pio0-4 */
                 .mwdma_mask     = 0x07,                 /* mwdma0-2 */
                 .udma_mask      = 0x3f,                 /* udma0-5 */
@@ -227,7 +227,7 @@ static const struct ata_port_info sil_port_info[] = {
         /* sil_3112_no_sata_irq */
         {
                 .sht            = &sil_sht,
-                .host_flags     = SIL_DFL_HOST_FLAGS | SIL_FLAG_MOD15WRITE |
+                .flags          = SIL_DFL_PORT_FLAGS | SIL_FLAG_MOD15WRITE |
                                   SIL_FLAG_NO_SATA_IRQ,
                 .pio_mask       = 0x1f,                 /* pio0-4 */
                 .mwdma_mask     = 0x07,                 /* mwdma0-2 */
@@ -237,7 +237,7 @@ static const struct ata_port_info sil_port_info[] = {
         /* sil_3512 */
         {
                 .sht            = &sil_sht,
-                .host_flags     = SIL_DFL_HOST_FLAGS | SIL_FLAG_RERR_ON_DMA_ACT,
+                .flags          = SIL_DFL_PORT_FLAGS | SIL_FLAG_RERR_ON_DMA_ACT,
                 .pio_mask       = 0x1f,                 /* pio0-4 */
                 .mwdma_mask     = 0x07,                 /* mwdma0-2 */
                 .udma_mask      = 0x3f,                 /* udma0-5 */
@@ -246,7 +246,7 @@ static const struct ata_port_info sil_port_info[] = {
         /* sil_3114 */
         {
                 .sht            = &sil_sht,
-                .host_flags     = SIL_DFL_HOST_FLAGS | SIL_FLAG_RERR_ON_DMA_ACT,
+                .flags          = SIL_DFL_PORT_FLAGS | SIL_FLAG_RERR_ON_DMA_ACT,
                 .pio_mask       = 0x1f,                 /* pio0-4 */
                 .mwdma_mask     = 0x07,                 /* mwdma0-2 */
                 .udma_mask      = 0x3f,                 /* udma0-5 */
@@ -295,10 +295,9 @@ static unsigned char sil_get_device_cache_line(struct pci_dev *pdev)
 
 static void sil_post_set_mode (struct ata_port *ap)
 {
-        struct ata_host_set *host_set = ap->host_set;
+        struct ata_host *host = ap->host;
         struct ata_device *dev;
-        void __iomem *addr =
-                host_set->mmio_base + sil_port[ap->port_no].xfer_mode;
+        void __iomem *addr = host->mmio_base + sil_port[ap->port_no].xfer_mode;
         u32 tmp, dev_mode[2];
         unsigned int i;
 
@@ -440,15 +439,15 @@ static void sil_host_intr(struct ata_port *ap, u32 bmdma2)
 static irqreturn_t sil_interrupt(int irq, void *dev_instance,
                                  struct pt_regs *regs)
 {
-        struct ata_host_set *host_set = dev_instance;
-        void __iomem *mmio_base = host_set->mmio_base;
+        struct ata_host *host = dev_instance;
+        void __iomem *mmio_base = host->mmio_base;
         int handled = 0;
         int i;
 
-        spin_lock(&host_set->lock);
+        spin_lock(&host->lock);
 
-        for (i = 0; i < host_set->n_ports; i++) {
-                struct ata_port *ap = host_set->ports[i];
+        for (i = 0; i < host->n_ports; i++) {
+                struct ata_port *ap = host->ports[i];
                 u32 bmdma2 = readl(mmio_base + sil_port[ap->port_no].bmdma2);
 
                 if (unlikely(!ap || ap->flags & ATA_FLAG_DISABLED))
@@ -466,14 +465,14 @@ static irqreturn_t sil_interrupt(int irq, void *dev_instance,
                 handled = 1;
         }
 
-        spin_unlock(&host_set->lock);
+        spin_unlock(&host->lock);
 
         return IRQ_RETVAL(handled);
 }
 
 static void sil_freeze(struct ata_port *ap)
 {
-        void __iomem *mmio_base = ap->host_set->mmio_base;
+        void __iomem *mmio_base = ap->host->mmio_base;
         u32 tmp;
 
         /* global IRQ mask doesn't block SATA IRQ, turn off explicitly */
@@ -488,7 +487,7 @@ static void sil_freeze(struct ata_port *ap)
 
 static void sil_thaw(struct ata_port *ap)
 {
-        void __iomem *mmio_base = ap->host_set->mmio_base;
+        void __iomem *mmio_base = ap->host->mmio_base;
         u32 tmp;
 
         /* clear IRQ */
@@ -567,7 +566,7 @@ static void sil_dev_config(struct ata_port *ap, struct ata_device *dev)
 }
 
 static void sil_init_controller(struct pci_dev *pdev,
-                                int n_ports, unsigned long host_flags,
+                                int n_ports, unsigned long port_flags,
                                 void __iomem *mmio_base)
 {
         u8 cls;
@@ -587,7 +586,7 @@ static void sil_init_controller(struct pci_dev *pdev,
                            "cache line size not set.  Driver may not function\n");
 
         /* Apply R_ERR on DMA activate FIS errata workaround */
-        if (host_flags & SIL_FLAG_RERR_ON_DMA_ACT) {
+        if (port_flags & SIL_FLAG_RERR_ON_DMA_ACT) {
                 int cnt;
 
                 for (i = 0, cnt = 0; i < n_ports; i++) {
@@ -658,7 +657,7 @@ static int sil_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
         probe_ent->udma_mask = sil_port_info[ent->driver_data].udma_mask;
         probe_ent->irq = pdev->irq;
         probe_ent->irq_flags = IRQF_SHARED;
-        probe_ent->host_flags = sil_port_info[ent->driver_data].host_flags;
+        probe_ent->port_flags = sil_port_info[ent->driver_data].flags;
 
         mmio_base = pci_iomap(pdev, 5, 0);
         if (mmio_base == NULL) {
@@ -679,7 +678,7 @@ static int sil_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
                 ata_std_ports(&probe_ent->port[i]);
         }
 
-        sil_init_controller(pdev, probe_ent->n_ports, probe_ent->host_flags,
+        sil_init_controller(pdev, probe_ent->n_ports, probe_ent->port_flags,
                             mmio_base);
 
         pci_set_master(pdev);
@@ -700,21 +699,23 @@ err_out:
         return rc;
 }
 
+#ifdef CONFIG_PM
 static int sil_pci_device_resume(struct pci_dev *pdev)
 {
-        struct ata_host_set *host_set = dev_get_drvdata(&pdev->dev);
+        struct ata_host *host = dev_get_drvdata(&pdev->dev);
 
         ata_pci_device_do_resume(pdev);
-        sil_init_controller(pdev, host_set->n_ports, host_set->ports[0]->flags,
-                            host_set->mmio_base);
-        ata_host_set_resume(host_set);
+        sil_init_controller(pdev, host->n_ports, host->ports[0]->flags,
+                            host->mmio_base);
+        ata_host_resume(host);
 
         return 0;
 }
+#endif
 
 static int __init sil_init(void)
 {
-        return pci_module_init(&sil_pci_driver);
+        return pci_register_driver(&sil_pci_driver);
 }
 
 static void __exit sil_exit(void)
diff --git a/drivers/scsi/sata_sil24.c b/drivers/ata/sata_sil24.c
index 3f368c7d3ef9..39cb07baebae 100644
--- a/drivers/scsi/sata_sil24.c
+++ b/drivers/ata/sata_sil24.c
@@ -316,7 +316,7 @@ struct sil24_port_priv {
         struct ata_taskfile tf;                 /* Cached taskfile registers */
 };
 
-/* ap->host_set->private_data */
+/* ap->host->private_data */
 struct sil24_host_priv {
         void __iomem *host_base;        /* global controller control (128 bytes @BAR0) */
         void __iomem *port_base;        /* port registers (4 * 8192 bytes @BAR2) */
@@ -337,9 +337,11 @@ static void sil24_error_handler(struct ata_port *ap);
 static void sil24_post_internal_cmd(struct ata_queued_cmd *qc);
 static int sil24_port_start(struct ata_port *ap);
 static void sil24_port_stop(struct ata_port *ap);
-static void sil24_host_stop(struct ata_host_set *host_set);
+static void sil24_host_stop(struct ata_host *host);
 static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
+#ifdef CONFIG_PM
 static int sil24_pci_device_resume(struct pci_dev *pdev);
+#endif
 
 static const struct pci_device_id sil24_pci_tbl[] = {
         { 0x1095, 0x3124, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BID_SIL3124 },
@@ -355,8 +357,10 @@ static struct pci_driver sil24_pci_driver = {
         .id_table               = sil24_pci_tbl,
         .probe                  = sil24_init_one,
         .remove                 = ata_pci_remove_one, /* safe? */
+#ifdef CONFIG_PM
         .suspend                = ata_pci_device_suspend,
         .resume                 = sil24_pci_device_resume,
+#endif
 };
 
 static struct scsi_host_template sil24_sht = {
@@ -411,7 +415,7 @@ static const struct ata_port_operations sil24_ops = {
 };
 
 /*
- * Use bits 30-31 of host_flags to encode available port numbers.
+ * Use bits 30-31 of port_flags to encode available port numbers.
  * Current maxium is 4.
  */
 #define SIL24_NPORTS2FLAG(nports)       ((((unsigned)(nports) - 1) & 0x3) << 30)
@@ -421,7 +425,7 @@ static struct ata_port_info sil24_port_info[] = {
         /* sil_3124 */
         {
                 .sht            = &sil24_sht,
-                .host_flags     = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(4) |
+                .flags          = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(4) |
                                   SIL24_FLAG_PCIX_IRQ_WOC,
                 .pio_mask       = 0x1f,                 /* pio0-4 */
                 .mwdma_mask     = 0x07,                 /* mwdma0-2 */
@@ -431,7 +435,7 @@ static struct ata_port_info sil24_port_info[] = {
         /* sil_3132 */
         {
                 .sht            = &sil24_sht,
-                .host_flags     = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(2),
+                .flags          = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(2),
                 .pio_mask       = 0x1f,                 /* pio0-4 */
                 .mwdma_mask     = 0x07,                 /* mwdma0-2 */
                 .udma_mask      = 0x3f,                 /* udma0-5 */
@@ -440,7 +444,7 @@ static struct ata_port_info sil24_port_info[] = {
         /* sil_3131/sil_3531 */
         {
                 .sht            = &sil24_sht,
-                .host_flags     = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(1),
+                .flags          = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(1),
                 .pio_mask       = 0x1f,                 /* pio0-4 */
                 .mwdma_mask     = 0x07,                 /* mwdma0-2 */
                 .udma_mask      = 0x3f,                 /* udma0-5 */
@@ -867,8 +871,8 @@ static inline void sil24_host_intr(struct ata_port *ap)
 
 static irqreturn_t sil24_interrupt(int irq, void *dev_instance, struct pt_regs *regs)
 {
-        struct ata_host_set *host_set = dev_instance;
-        struct sil24_host_priv *hpriv = host_set->private_data;
+        struct ata_host *host = dev_instance;
+        struct sil24_host_priv *hpriv = host->private_data;
         unsigned handled = 0;
         u32 status;
         int i;
@@ -884,20 +888,20 @@ static irqreturn_t sil24_interrupt(int irq, void *dev_instance, struct pt_regs *
         if (!(status & IRQ_STAT_4PORTS))
                 goto out;
 
-        spin_lock(&host_set->lock);
+        spin_lock(&host->lock);
 
-        for (i = 0; i < host_set->n_ports; i++)
+        for (i = 0; i < host->n_ports; i++)
                 if (status & (1 << i)) {
-                        struct ata_port *ap = host_set->ports[i];
+                        struct ata_port *ap = host->ports[i];
                         if (ap && !(ap->flags & ATA_FLAG_DISABLED)) {
-                                sil24_host_intr(host_set->ports[i]);
+                                sil24_host_intr(host->ports[i]);
                                 handled++;
                         } else
                                 printk(KERN_ERR DRV_NAME
                                        ": interrupt from disabled port %d\n", i);
                 }
 
-        spin_unlock(&host_set->lock);
+        spin_unlock(&host->lock);
  out:
         return IRQ_RETVAL(handled);
 }
@@ -937,7 +941,7 @@ static inline void sil24_cblk_free(struct sil24_port_priv *pp, struct device *de
 
 static int sil24_port_start(struct ata_port *ap)
 {
-        struct device *dev = ap->host_set->dev;
+        struct device *dev = ap->host->dev;
         struct sil24_port_priv *pp;
         union sil24_cmd_block *cb;
         size_t cb_size = sizeof(*cb) * SIL24_MAX_CMDS;
@@ -976,7 +980,7 @@ err_out:
 
 static void sil24_port_stop(struct ata_port *ap)
 {
-        struct device *dev = ap->host_set->dev;
+        struct device *dev = ap->host->dev;
         struct sil24_port_priv *pp = ap->private_data;
 
         sil24_cblk_free(pp, dev);
@@ -984,10 +988,10 @@ static void sil24_port_stop(struct ata_port *ap)
         kfree(pp);
 }
 
-static void sil24_host_stop(struct ata_host_set *host_set)
+static void sil24_host_stop(struct ata_host *host)
 {
-        struct sil24_host_priv *hpriv = host_set->private_data;
-        struct pci_dev *pdev = to_pci_dev(host_set->dev);
+        struct sil24_host_priv *hpriv = host->private_data;
+        struct pci_dev *pdev = to_pci_dev(host->dev);
 
         pci_iounmap(pdev, hpriv->host_base);
         pci_iounmap(pdev, hpriv->port_base);
@@ -995,7 +999,7 @@ static void sil24_host_stop(struct ata_host_set *host_set)
 }
 
 static void sil24_init_controller(struct pci_dev *pdev, int n_ports,
-                                  unsigned long host_flags,
+                                  unsigned long port_flags,
                                   void __iomem *host_base,
                                   void __iomem *port_base)
 {
@@ -1028,7 +1032,7 @@ static void sil24_init_controller(struct pci_dev *pdev, int n_ports,
                 }
 
                 /* Configure IRQ WoC */
-                if (host_flags & SIL24_FLAG_PCIX_IRQ_WOC)
+                if (port_flags & SIL24_FLAG_PCIX_IRQ_WOC)
                         writel(PORT_CS_IRQ_WOC, port + PORT_CTRL_STAT);
                 else
                         writel(PORT_CS_IRQ_WOC, port + PORT_CTRL_CLR);
@@ -1097,12 +1101,12 @@ static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
         INIT_LIST_HEAD(&probe_ent->node);
 
         probe_ent->sht          = pinfo->sht;
-        probe_ent->host_flags   = pinfo->host_flags;
+        probe_ent->port_flags   = pinfo->flags;
         probe_ent->pio_mask     = pinfo->pio_mask;
         probe_ent->mwdma_mask   = pinfo->mwdma_mask;
         probe_ent->udma_mask    = pinfo->udma_mask;
         probe_ent->port_ops     = pinfo->port_ops;
-        probe_ent->n_ports      = SIL24_FLAG2NPORTS(pinfo->host_flags);
+        probe_ent->n_ports      = SIL24_FLAG2NPORTS(pinfo->flags);
 
         probe_ent->irq = pdev->irq;
         probe_ent->irq_flags = IRQF_SHARED;
@@ -1140,14 +1144,14 @@ static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
         }
 
         /* Apply workaround for completion IRQ loss on PCI-X errata */
-        if (probe_ent->host_flags & SIL24_FLAG_PCIX_IRQ_WOC) {
+        if (probe_ent->port_flags & SIL24_FLAG_PCIX_IRQ_WOC) {
                 tmp = readl(host_base + HOST_CTRL);
                 if (tmp & (HOST_CTRL_TRDY | HOST_CTRL_STOP | HOST_CTRL_DEVSEL))
                         dev_printk(KERN_INFO, &pdev->dev,
                                    "Applying completion IRQ loss on PCI-X "
                                    "errata fix\n");
                 else
-                        probe_ent->host_flags &= ~SIL24_FLAG_PCIX_IRQ_WOC;
+                        probe_ent->port_flags &= ~SIL24_FLAG_PCIX_IRQ_WOC;
         }
 
         for (i = 0; i < probe_ent->n_ports; i++) {
@@ -1160,7 +1164,7 @@ static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
                 ata_std_ports(&probe_ent->port[i]);
         }
 
-        sil24_init_controller(pdev, probe_ent->n_ports, probe_ent->host_flags,
+        sil24_init_controller(pdev, probe_ent->n_ports, probe_ent->port_flags,
                               host_base, port_base);
 
         pci_set_master(pdev);
@@ -1184,28 +1188,29 @@ static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
         return rc;
 }
 
+#ifdef CONFIG_PM
 static int sil24_pci_device_resume(struct pci_dev *pdev)
 {
-        struct ata_host_set *host_set = dev_get_drvdata(&pdev->dev);
-        struct sil24_host_priv *hpriv = host_set->private_data;
+        struct ata_host *host = dev_get_drvdata(&pdev->dev);
+        struct sil24_host_priv *hpriv = host->private_data;
 
         ata_pci_device_do_resume(pdev);
 
         if (pdev->dev.power.power_state.event == PM_EVENT_SUSPEND)
                 writel(HOST_CTRL_GLOBAL_RST, hpriv->host_base + HOST_CTRL);
 
-        sil24_init_controller(pdev, host_set->n_ports,
-                              host_set->ports[0]->flags,
+        sil24_init_controller(pdev, host->n_ports, host->ports[0]->flags,
                               hpriv->host_base, hpriv->port_base);
 
-        ata_host_set_resume(host_set);
+        ata_host_resume(host);
 
         return 0;
 }
+#endif
 
 static int __init sil24_init(void)
 {
-        return pci_module_init(&sil24_pci_driver);
+        return pci_register_driver(&sil24_pci_driver);
 }
 
 static void __exit sil24_exit(void)
diff --git a/drivers/scsi/sata_sis.c b/drivers/ata/sata_sis.c
index ee6b5df41d30..9b17375d8056 100644
--- a/drivers/scsi/sata_sis.c
+++ b/drivers/ata/sata_sis.c
@@ -128,7 +128,7 @@ static const struct ata_port_operations sis_ops = {
 
 static struct ata_port_info sis_port_info = {
         .sht            = &sis_sht,
-        .host_flags     = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
+        .flags          = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
         .pio_mask       = 0x1f,
         .mwdma_mask     = 0x7,
         .udma_mask      = 0x7f,
@@ -158,7 +158,7 @@ static unsigned int get_scr_cfg_addr(unsigned int port_no, unsigned int sc_reg,
 
 static u32 sis_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg)
 {
-        struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
         unsigned int cfg_addr = get_scr_cfg_addr(ap->port_no, sc_reg, pdev->device);
         u32 val, val2 = 0;
         u8 pmr;
@@ -178,7 +178,7 @@ static u32 sis_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg)
 
 static void sis_scr_cfg_write (struct ata_port *ap, unsigned int scr, u32 val)
 {
-        struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
         unsigned int cfg_addr = get_scr_cfg_addr(ap->port_no, scr, pdev->device);
         u8 pmr;
 
@@ -195,7 +195,7 @@ static void sis_scr_cfg_write (struct ata_port *ap, unsigned int scr, u32 val)
 
 static u32 sis_scr_read (struct ata_port *ap, unsigned int sc_reg)
 {
-        struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
         u32 val, val2 = 0;
         u8 pmr;
 
@@ -217,7 +217,7 @@ static u32 sis_scr_read (struct ata_port *ap, unsigned int sc_reg)
 
 static void sis_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
 {
-        struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
         u8 pmr;
 
         if (sc_reg > SCR_CONTROL)
@@ -275,17 +275,17 @@ static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
         /* check and see if the SCRs are in IO space or PCI cfg space */
         pci_read_config_dword(pdev, SIS_GENCTL, &genctl);
         if ((genctl & GENCTL_IOMAPPED_SCR) == 0)
-                probe_ent->host_flags |= SIS_FLAG_CFGSCR;
+                probe_ent->port_flags |= SIS_FLAG_CFGSCR;
 
         /* if hardware thinks SCRs are in IO space, but there are
          * no IO resources assigned, change to PCI cfg space.
          */
-        if ((!(probe_ent->host_flags & SIS_FLAG_CFGSCR)) &&
+        if ((!(probe_ent->port_flags & SIS_FLAG_CFGSCR)) &&
             ((pci_resource_start(pdev, SIS_SCR_PCI_BAR) == 0) ||
              (pci_resource_len(pdev, SIS_SCR_PCI_BAR) < 128))) {
                 genctl &= ~GENCTL_IOMAPPED_SCR;
                 pci_write_config_dword(pdev, SIS_GENCTL, genctl);
-                probe_ent->host_flags |= SIS_FLAG_CFGSCR;
+                probe_ent->port_flags |= SIS_FLAG_CFGSCR;
         }
 
         pci_read_config_byte(pdev, SIS_PMR, &pmr);
@@ -306,7 +306,7 @@ static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
                 port2_start = 0x20;
         }
 
-        if (!(probe_ent->host_flags & SIS_FLAG_CFGSCR)) {
+        if (!(probe_ent->port_flags & SIS_FLAG_CFGSCR)) {
                 probe_ent->port[0].scr_addr =
                         pci_resource_start(pdev, SIS_SCR_PCI_BAR);
                 probe_ent->port[1].scr_addr =
@@ -334,7 +334,7 @@ err_out:
 
 static int __init sis_init(void)
 {
-        return pci_module_init(&sis_pci_driver);
+        return pci_register_driver(&sis_pci_driver);
 }
 
 static void __exit sis_exit(void)
diff --git a/drivers/scsi/sata_svw.c b/drivers/ata/sata_svw.c
index 7d0858095e1f..2a7e3495cf16 100644
--- a/drivers/scsi/sata_svw.c
+++ b/drivers/ata/sata_svw.c
@@ -169,7 +169,7 @@ static void k2_sata_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
  *      @qc: Info associated with this ATA transaction.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 static void k2_bmdma_setup_mmio (struct ata_queued_cmd *qc)
@@ -199,7 +199,7 @@ static void k2_bmdma_setup_mmio (struct ata_queued_cmd *qc)
  *      @qc: Info associated with this ATA transaction.
  *
  *      LOCKING:
- *      spin_lock_irqsave(host_set lock)
+ *      spin_lock_irqsave(host lock)
  */
 
 static void k2_bmdma_start_mmio (struct ata_queued_cmd *qc)
@@ -261,12 +261,12 @@ static int k2_sata_proc_info(struct Scsi_Host *shost, char *page, char **start,
                 return 0;
 
         /* Find the OF node for the PCI device proper */
-        np = pci_device_to_OF_node(to_pci_dev(ap->host_set->dev));
+        np = pci_device_to_OF_node(to_pci_dev(ap->host->dev));
         if (np == NULL)
                 return 0;
 
         /* Match it to a port node */
-        index = (ap == ap->host_set->ports[0]) ? 0 : 1;
+        index = (ap == ap->host->ports[0]) ? 0 : 1;
         for (np = np->child; np != NULL; np = np->sibling) {
                 u32 *reg = (u32 *)get_property(np, "reg", NULL);
                 if (!reg)
@@ -423,7 +423,7 @@ static int k2_sata_init_one (struct pci_dev *pdev, const struct pci_device_id *e
         writel(0x0, mmio_base + K2_SATA_SIM_OFFSET);
 
         probe_ent->sht = &k2_sata_sht;
-        probe_ent->host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+        probe_ent->port_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
                                 ATA_FLAG_MMIO;
         probe_ent->port_ops = &k2_sata_ops;
         probe_ent->n_ports = 4;
@@ -488,7 +488,7 @@ static struct pci_driver k2_sata_pci_driver = {
 
 static int __init k2_sata_init(void)
 {
-        return pci_module_init(&k2_sata_pci_driver);
+        return pci_register_driver(&k2_sata_pci_driver);
 }
 
 
diff --git a/drivers/scsi/sata_sx4.c b/drivers/ata/sata_sx4.c
index ccc8cad24f7d..091867e10ea3 100644
--- a/drivers/scsi/sata_sx4.c
+++ b/drivers/ata/sata_sx4.c
@@ -160,7 +160,7 @@ static void pdc_port_stop(struct ata_port *ap);
 static void pdc20621_qc_prep(struct ata_queued_cmd *qc);
 static void pdc_tf_load_mmio(struct ata_port *ap, const struct ata_taskfile *tf);
 static void pdc_exec_command_mmio(struct ata_port *ap, const struct ata_taskfile *tf);
-static void pdc20621_host_stop(struct ata_host_set *host_set);
+static void pdc20621_host_stop(struct ata_host *host);
 static unsigned int pdc20621_dimm_init(struct ata_probe_ent *pe);
 static int pdc20621_detect_dimm(struct ata_probe_ent *pe);
 static unsigned int pdc20621_i2c_read(struct ata_probe_ent *pe,
@@ -218,7 +218,7 @@ static const struct ata_port_info pdc_port_info[] = {
         /* board_20621 */
         {
                 .sht            = &pdc_sata_sht,
-                .host_flags     = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+                .flags          = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
                                   ATA_FLAG_SRST | ATA_FLAG_MMIO |
                                   ATA_FLAG_NO_ATAPI | ATA_FLAG_PIO_POLLING,
                 .pio_mask       = 0x1f, /* pio0-4 */
@@ -244,21 +244,21 @@ static struct pci_driver pdc_sata_pci_driver = {
 };
 
 
-static void pdc20621_host_stop(struct ata_host_set *host_set)
+static void pdc20621_host_stop(struct ata_host *host)
 {
-        struct pci_dev *pdev = to_pci_dev(host_set->dev);
-        struct pdc_host_priv *hpriv = host_set->private_data;
+        struct pci_dev *pdev = to_pci_dev(host->dev);
+        struct pdc_host_priv *hpriv = host->private_data;
         void __iomem *dimm_mmio = hpriv->dimm_mmio;
 
         pci_iounmap(pdev, dimm_mmio);
         kfree(hpriv);
 
-        pci_iounmap(pdev, host_set->mmio_base);
+        pci_iounmap(pdev, host->mmio_base);
 }
 
 static int pdc_port_start(struct ata_port *ap)
 {
-        struct device *dev = ap->host_set->dev;
+        struct device *dev = ap->host->dev;
         struct pdc_port_priv *pp;
         int rc;
 
@@ -293,7 +293,7 @@ err_out:
 
 static void pdc_port_stop(struct ata_port *ap)
 {
-        struct device *dev = ap->host_set->dev;
+        struct device *dev = ap->host->dev;
         struct pdc_port_priv *pp = ap->private_data;
 
         ap->private_data = NULL;
@@ -453,8 +453,8 @@ static void pdc20621_dma_prep(struct ata_queued_cmd *qc)
         struct scatterlist *sg;
         struct ata_port *ap = qc->ap;
         struct pdc_port_priv *pp = ap->private_data;
-        void __iomem *mmio = ap->host_set->mmio_base;
-        struct pdc_host_priv *hpriv = ap->host_set->private_data;
+        void __iomem *mmio = ap->host->mmio_base;
+        struct pdc_host_priv *hpriv = ap->host->private_data;
         void __iomem *dimm_mmio = hpriv->dimm_mmio;
         unsigned int portno = ap->port_no;
         unsigned int i, idx, total_len = 0, sgt_len;
@@ -514,8 +514,8 @@ static void pdc20621_nodata_prep(struct ata_queued_cmd *qc)
 {
         struct ata_port *ap = qc->ap;
         struct pdc_port_priv *pp = ap->private_data;
-        void __iomem *mmio = ap->host_set->mmio_base;
-        struct pdc_host_priv *hpriv = ap->host_set->private_data;
+        void __iomem *mmio = ap->host->mmio_base;
+        struct pdc_host_priv *hpriv = ap->host->private_data;
         void __iomem *dimm_mmio = hpriv->dimm_mmio;
         unsigned int portno = ap->port_no;
         unsigned int i;
@@ -565,8 +565,8 @@ static void __pdc20621_push_hdma(struct ata_queued_cmd *qc,
                                  u32 pkt_ofs)
 {
         struct ata_port *ap = qc->ap;
-        struct ata_host_set *host_set = ap->host_set;
-        void __iomem *mmio = host_set->mmio_base;
+        struct ata_host *host = ap->host;
+        void __iomem *mmio = host->mmio_base;
 
         /* hard-code chip #0 */
         mmio += PDC_CHIP0_OFS;
@@ -583,7 +583,7 @@ static void pdc20621_push_hdma(struct ata_queued_cmd *qc,
                                 u32 pkt_ofs)
 {
         struct ata_port *ap = qc->ap;
-        struct pdc_host_priv *pp = ap->host_set->private_data;
+        struct pdc_host_priv *pp = ap->host->private_data;
         unsigned int idx = pp->hdma_prod & PDC_HDMA_Q_MASK;
 
         if (!pp->doing_hdma) {
@@ -601,7 +601,7 @@ static void pdc20621_push_hdma(struct ata_queued_cmd *qc,
 static void pdc20621_pop_hdma(struct ata_queued_cmd *qc)
 {
         struct ata_port *ap = qc->ap;
-        struct pdc_host_priv *pp = ap->host_set->private_data;
+        struct pdc_host_priv *pp = ap->host->private_data;
         unsigned int idx = pp->hdma_cons & PDC_HDMA_Q_MASK;
 
         /* if nothing on queue, we're done */
@@ -620,7 +620,7 @@ static void pdc20621_dump_hdma(struct ata_queued_cmd *qc)
 {
         struct ata_port *ap = qc->ap;
         unsigned int port_no = ap->port_no;
-        struct pdc_host_priv *hpriv = ap->host_set->private_data;
+        struct pdc_host_priv *hpriv = ap->host->private_data;
         void *dimm_mmio = hpriv->dimm_mmio;
 
         dimm_mmio += (port_no * PDC_DIMM_WINDOW_STEP);
@@ -638,9 +638,9 @@ static inline void pdc20621_dump_hdma(struct ata_queued_cmd *qc) { }
 static void pdc20621_packet_start(struct ata_queued_cmd *qc)
 {
         struct ata_port *ap = qc->ap;
-        struct ata_host_set *host_set = ap->host_set;
+        struct ata_host *host = ap->host;
         unsigned int port_no = ap->port_no;
-        void __iomem *mmio = host_set->mmio_base;
+        void __iomem *mmio = host->mmio_base;
         unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE);
         u8 seq = (u8) (port_no + 1);
         unsigned int port_ofs;
@@ -781,8 +781,8 @@ static inline unsigned int pdc20621_host_intr( struct ata_port *ap,
 
 static void pdc20621_irq_clear(struct ata_port *ap)
 {
-        struct ata_host_set *host_set = ap->host_set;
-        void __iomem *mmio = host_set->mmio_base;
+        struct ata_host *host = ap->host;
+        void __iomem *mmio = host->mmio_base;
 
         mmio += PDC_CHIP0_OFS;
 
@@ -791,7 +791,7 @@ static void pdc20621_irq_clear(struct ata_port *ap)
 
 static irqreturn_t pdc20621_interrupt (int irq, void *dev_instance, struct pt_regs *regs)
 {
-        struct ata_host_set *host_set = dev_instance;
+        struct ata_host *host = dev_instance;
         struct ata_port *ap;
         u32 mask = 0;
         unsigned int i, tmp, port_no;
@@ -800,12 +800,12 @@ static irqreturn_t pdc20621_interrupt (int irq, void *dev_instance, struct pt_re
 
         VPRINTK("ENTER\n");
 
-        if (!host_set || !host_set->mmio_base) {
+        if (!host || !host->mmio_base) {
                 VPRINTK("QUICK EXIT\n");
                 return IRQ_NONE;
         }
 
-        mmio_base = host_set->mmio_base;
+        mmio_base = host->mmio_base;
 
         /* reading should also clear interrupts */
         mmio_base += PDC_CHIP0_OFS;
@@ -822,16 +822,16 @@ static irqreturn_t pdc20621_interrupt (int irq, void *dev_instance, struct pt_re
                 return IRQ_NONE;
         }
 
-        spin_lock(&host_set->lock);
+        spin_lock(&host->lock);
 
         for (i = 1; i < 9; i++) {
                 port_no = i - 1;
                 if (port_no > 3)
                         port_no -= 4;
-                if (port_no >= host_set->n_ports)
+                if (port_no >= host->n_ports)
                         ap = NULL;
                 else
-                        ap = host_set->ports[port_no];
+                        ap = host->ports[port_no];
                 tmp = mask & (1 << i);
                 VPRINTK("seq %u, port_no %u, ap %p, tmp %x\n", i, port_no, ap, tmp);
                 if (tmp && ap &&
@@ -845,7 +845,7 @@ static irqreturn_t pdc20621_interrupt (int irq, void *dev_instance, struct pt_re
                 }
         }
 
-        spin_unlock(&host_set->lock);
+        spin_unlock(&host->lock);
 
         VPRINTK("mask == 0x%x\n", mask);
 
@@ -857,13 +857,13 @@ static irqreturn_t pdc20621_interrupt (int irq, void *dev_instance, struct pt_re
 static void pdc_eng_timeout(struct ata_port *ap)
 {
         u8 drv_stat;
-        struct ata_host_set *host_set = ap->host_set;
+        struct ata_host *host = ap->host;
         struct ata_queued_cmd *qc;
         unsigned long flags;
 
         DPRINTK("ENTER\n");
 
-        spin_lock_irqsave(&host_set->lock, flags);
+        spin_lock_irqsave(&host->lock, flags);
 
         qc = ata_qc_from_tag(ap, ap->active_tag);
 
@@ -885,7 +885,7 @@ static void pdc_eng_timeout(struct ata_port *ap)
                 break;
         }
 
-        spin_unlock_irqrestore(&host_set->lock, flags);
+        spin_unlock_irqrestore(&host->lock, flags);
         ata_eh_qc_complete(qc);
         DPRINTK("EXIT\n");
 }
@@ -1429,7 +1429,7 @@ static int pdc_sata_init_one (struct pci_dev *pdev, const struct pci_device_id *
         hpriv->dimm_mmio = dimm_mmio;
 
         probe_ent->sht          = pdc_port_info[board_idx].sht;
-        probe_ent->host_flags   = pdc_port_info[board_idx].host_flags;
+        probe_ent->port_flags   = pdc_port_info[board_idx].flags;
         probe_ent->pio_mask     = pdc_port_info[board_idx].pio_mask;
         probe_ent->mwdma_mask   = pdc_port_info[board_idx].mwdma_mask;
         probe_ent->udma_mask    = pdc_port_info[board_idx].udma_mask;
@@ -1482,7 +1482,7 @@ err_out:
 
 static int __init pdc_sata_init(void)
 {
-        return pci_module_init(&pdc_sata_pci_driver);
+        return pci_register_driver(&pdc_sata_pci_driver);
 }
 
 
diff --git a/drivers/scsi/sata_uli.c b/drivers/ata/sata_uli.c
index 33cdb4867ef1..8fc6e800011a 100644
--- a/drivers/scsi/sata_uli.c
+++ b/drivers/ata/sata_uli.c
@@ -128,7 +128,7 @@ static const struct ata_port_operations uli_ops = {
 
 static struct ata_port_info uli_port_info = {
         .sht            = &uli_sht,
-        .host_flags     = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
+        .flags          = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
         .pio_mask       = 0x1f,         /* pio0-4 */
         .udma_mask      = 0x7f,         /* udma0-6 */
         .port_ops       = &uli_ops,
@@ -143,13 +143,13 @@ MODULE_VERSION(DRV_VERSION);
 
 static unsigned int get_scr_cfg_addr(struct ata_port *ap, unsigned int sc_reg)
 {
-        struct uli_priv *hpriv = ap->host_set->private_data;
+        struct uli_priv *hpriv = ap->host->private_data;
         return hpriv->scr_cfg_addr[ap->port_no] + (4 * sc_reg);
 }
 
 static u32 uli_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg)
 {
-        struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
         unsigned int cfg_addr = get_scr_cfg_addr(ap, sc_reg);
         u32 val;
 
@@ -159,7 +159,7 @@ static u32 uli_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg)
 
 static void uli_scr_cfg_write (struct ata_port *ap, unsigned int scr, u32 val)
 {
-        struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
         unsigned int cfg_addr = get_scr_cfg_addr(ap, scr);
 
         pci_write_config_dword(pdev, cfg_addr, val);
@@ -287,7 +287,7 @@ err_out:
 
 static int __init uli_init(void)
 {
-        return pci_module_init(&uli_pci_driver);
+        return pci_register_driver(&uli_pci_driver);
 }
 
 static void __exit uli_exit(void)
diff --git a/drivers/scsi/sata_via.c b/drivers/ata/sata_via.c
index 01d40369a8a5..7f087aef99de 100644
--- a/drivers/scsi/sata_via.c
+++ b/drivers/ata/sata_via.c
@@ -77,6 +77,7 @@ static void svia_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
 static void vt6420_error_handler(struct ata_port *ap);
 
 static const struct pci_device_id svia_pci_tbl[] = {
+        { 0x1106, 0x0591, PCI_ANY_ID, PCI_ANY_ID, 0, 0, vt6420 },
         { 0x1106, 0x3149, PCI_ANY_ID, PCI_ANY_ID, 0, 0, vt6420 },
         { 0x1106, 0x3249, PCI_ANY_ID, PCI_ANY_ID, 0, 0, vt6421 },
 
@@ -175,7 +176,7 @@ static const struct ata_port_operations vt6421_sata_ops = {
 
 static struct ata_port_info vt6420_port_info = {
         .sht            = &svia_sht,
-        .host_flags     = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
+        .flags          = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
         .pio_mask       = 0x1f,
         .mwdma_mask     = 0x07,
         .udma_mask      = 0x7f,
@@ -345,7 +346,7 @@ static struct ata_probe_ent *vt6421_init_probe_ent(struct pci_dev *pdev)
         INIT_LIST_HEAD(&probe_ent->node);
 
         probe_ent->sht          = &svia_sht;
-        probe_ent->host_flags   = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY;
+        probe_ent->port_flags   = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY;
         probe_ent->port_ops     = &vt6421_sata_ops;
         probe_ent->n_ports      = N_PORTS;
         probe_ent->irq          = pdev->irq;
@@ -488,7 +489,7 @@ err_out:
 
 static int __init svia_init(void)
 {
-        return pci_module_init(&svia_pci_driver);
+        return pci_register_driver(&svia_pci_driver);
 }
 
 static void __exit svia_exit(void)
diff --git a/drivers/scsi/sata_vsc.c b/drivers/ata/sata_vsc.c
index ad37871594f5..d0d92f33de54 100644
--- a/drivers/scsi/sata_vsc.c
+++ b/drivers/ata/sata_vsc.c
@@ -123,7 +123,7 @@ static void vsc_intr_mask_update(struct ata_port *ap, u8 ctl)
         void __iomem *mask_addr;
         u8 mask;
 
-        mask_addr = ap->host_set->mmio_base +
+        mask_addr = ap->host->mmio_base +
                 VSC_SATA_INT_MASK_OFFSET + ap->port_no;
         mask = readb(mask_addr);
         if (ctl & ATA_NIEN)
@@ -206,20 +206,20 @@ static void vsc_sata_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
 static irqreturn_t vsc_sata_interrupt (int irq, void *dev_instance,
                                        struct pt_regs *regs)
 {
-        struct ata_host_set *host_set = dev_instance;
+        struct ata_host *host = dev_instance;
         unsigned int i;
         unsigned int handled = 0;
         u32 int_status;
 
-        spin_lock(&host_set->lock);
+        spin_lock(&host->lock);
 
-        int_status = readl(host_set->mmio_base + VSC_SATA_INT_STAT_OFFSET);
+        int_status = readl(host->mmio_base + VSC_SATA_INT_STAT_OFFSET);
 
-        for (i = 0; i < host_set->n_ports; i++) {
+        for (i = 0; i < host->n_ports; i++) {
                 if (int_status & ((u32) 0xFF << (8 * i))) {
                         struct ata_port *ap;
 
-                        ap = host_set->ports[i];
+                        ap = host->ports[i];
 
                         if (is_vsc_sata_int_err(i, int_status)) {
                                 u32 err_status;
@@ -259,7 +259,7 @@ static irqreturn_t vsc_sata_interrupt (int irq, void *dev_instance,
                 }
         }
 
-        spin_unlock(&host_set->lock);
+        spin_unlock(&host->lock);
 
         return IRQ_RETVAL(handled);
 }
@@ -395,7 +395,7 @@ static int __devinit vsc_sata_init_one (struct pci_dev *pdev, const struct pci_d
         pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, 0x80);
 
         probe_ent->sht = &vsc_sata_sht;
-        probe_ent->host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+        probe_ent->port_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
                                 ATA_FLAG_MMIO;
         probe_ent->port_ops = &vsc_sata_ops;
         probe_ent->n_ports = 4;
@@ -462,7 +462,7 @@ static struct pci_driver vsc_sata_pci_driver = {
 
 static int __init vsc_sata_init(void)
 {
-        return pci_module_init(&vsc_sata_pci_driver);
+        return pci_register_driver(&vsc_sata_pci_driver);
 }
 
 
diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
index 17e709e7d72a..def78a2a7c15 100644
--- a/drivers/pci/quirks.c
+++ b/drivers/pci/quirks.c
@@ -1210,7 +1210,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI,	PCI_DEVICE_ID_SI_962,		quirk_sis_96x_
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI,      PCI_DEVICE_ID_SI_963,           quirk_sis_96x_smbus );
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI,      PCI_DEVICE_ID_SI_LPC,           quirk_sis_96x_smbus );
 
-#if defined(CONFIG_SCSI_SATA) || defined(CONFIG_SCSI_SATA_MODULE)
+#if defined(CONFIG_ATA) || defined(CONFIG_ATA_MODULE)
 
 /*
  *      If we are using libata we can drive this chip properly but must
@@ -1300,7 +1300,7 @@ static int __init combined_setup(char *str)
 }
 __setup("combined_mode=", combined_setup);
 
-#ifdef CONFIG_SCSI_SATA_INTEL_COMBINED
+#ifdef CONFIG_SATA_INTEL_COMBINED
 static void __devinit quirk_intel_ide_combined(struct pci_dev *pdev)
 {
         u8 prog, comb, tmp;
@@ -1393,7 +1393,7 @@ static void __devinit quirk_intel_ide_combined(struct pci_dev *pdev)
                 request_region(0x170, 8, "libata");     /* port 1 */
 }
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL,    PCI_ANY_ID,       quirk_intel_ide_combined );
-#endif /* CONFIG_SCSI_SATA_INTEL_COMBINED */
+#endif /* CONFIG_SATA_INTEL_COMBINED */
 
 
 int pcie_mch_quirk;
diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig
index 96a81cd17617..2df4d15c9634 100644
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -471,67 +471,6 @@ config SCSI_IN2000
 
 source "drivers/scsi/megaraid/Kconfig.megaraid"
 
-config SCSI_SATA
-        tristate "Serial ATA (SATA) support"
-        depends on SCSI
-        help
-          This driver family supports Serial ATA host controllers
-          and devices.
-
-          If unsure, say N.
-
-config SCSI_SATA_AHCI
-        tristate "AHCI SATA support"
-        depends on SCSI_SATA && PCI
-        help
-          This option enables support for AHCI Serial ATA.
-
-          If unsure, say N.
-
-config SCSI_SATA_SVW
-        tristate "ServerWorks Frodo / Apple K2 SATA support"
-        depends on SCSI_SATA && PCI
-        help
-          This option enables support for Broadcom/Serverworks/Apple K2
-          SATA support.
-
-          If unsure, say N.
-
-config SCSI_ATA_PIIX
-        tristate "Intel PIIX/ICH SATA support"
-        depends on SCSI_SATA && PCI
-        help
-          This option enables support for ICH5/6/7/8 Serial ATA.
-          If PATA support was enabled previously, this enables
-          support for select Intel PIIX/ICH PATA host controllers.
-
-          If unsure, say N.
-
-config SCSI_SATA_MV
-        tristate "Marvell SATA support (HIGHLY EXPERIMENTAL)"
-        depends on SCSI_SATA && PCI && EXPERIMENTAL
-        help
-          This option enables support for the Marvell Serial ATA family.
-          Currently supports 88SX[56]0[48][01] chips.
-
-          If unsure, say N.
-
-config SCSI_SATA_NV
-        tristate "NVIDIA SATA support"
-        depends on SCSI_SATA && PCI && EXPERIMENTAL
-        help
-          This option enables support for NVIDIA Serial ATA.
-
-          If unsure, say N.
-
-config SCSI_PDC_ADMA
-        tristate "Pacific Digital ADMA support"
-        depends on SCSI_SATA && PCI
-        help
-          This option enables support for Pacific Digital ADMA controllers
-
-          If unsure, say N.
-
 config SCSI_HPTIOP
         tristate "HighPoint RocketRAID 3xxx Controller support"
         depends on SCSI && PCI
@@ -542,83 +481,6 @@ config SCSI_HPTIOP
           To compile this driver as a module, choose M here; the module
           will be called hptiop. If unsure, say N.
 
-config SCSI_SATA_QSTOR
-        tristate "Pacific Digital SATA QStor support"
-        depends on SCSI_SATA && PCI
-        help
-          This option enables support for Pacific Digital Serial ATA QStor.
-
-          If unsure, say N.
-
-config SCSI_SATA_PROMISE
-        tristate "Promise SATA TX2/TX4 support"
-        depends on SCSI_SATA && PCI
-        help
-          This option enables support for Promise Serial ATA TX2/TX4.
-
-          If unsure, say N.
-
-config SCSI_SATA_SX4
-        tristate "Promise SATA SX4 support"
-        depends on SCSI_SATA && PCI && EXPERIMENTAL
-        help
-          This option enables support for Promise Serial ATA SX4.
-
-          If unsure, say N.
-
-config SCSI_SATA_SIL
-        tristate "Silicon Image SATA support"
-        depends on SCSI_SATA && PCI && EXPERIMENTAL
-        help
-          This option enables support for Silicon Image Serial ATA.
-
-          If unsure, say N.
-
-config SCSI_SATA_SIL24
-        tristate "Silicon Image 3124/3132 SATA support"
-        depends on SCSI_SATA && PCI && EXPERIMENTAL
-        help
-          This option enables support for Silicon Image 3124/3132 Serial ATA.
-
-          If unsure, say N.
-
-config SCSI_SATA_SIS
-        tristate "SiS 964/180 SATA support"
-        depends on SCSI_SATA && PCI && EXPERIMENTAL
-        help
-          This option enables support for SiS Serial ATA 964/180.
-
-          If unsure, say N.
-
-config SCSI_SATA_ULI
-        tristate "ULi Electronics SATA support"
-        depends on SCSI_SATA && PCI && EXPERIMENTAL
-        help
-          This option enables support for ULi Electronics SATA.
-
-          If unsure, say N.
-
-config SCSI_SATA_VIA
-        tristate "VIA SATA support"
-        depends on SCSI_SATA && PCI
-        help
-          This option enables support for VIA Serial ATA.
-
-          If unsure, say N.
-
-config SCSI_SATA_VITESSE
-        tristate "VITESSE VSC-7174 / INTEL 31244 SATA support"
-        depends on SCSI_SATA && PCI
-        help
-          This option enables support for Vitesse VSC7174 and Intel 31244 Serial ATA.
-
-          If unsure, say N.
-
-config SCSI_SATA_INTEL_COMBINED
-        bool
-        depends on IDE=y && !BLK_DEV_IDE_SATA && (SCSI_SATA_AHCI || SCSI_ATA_PIIX)
-        default y
-
 config SCSI_BUSLOGIC
         tristate "BusLogic SCSI support"
         depends on (PCI || ISA || MCA) && SCSI && ISA_DMA_API
diff --git a/drivers/scsi/Makefile b/drivers/scsi/Makefile
index ebd0cf00bf3e..b678f957cfe2 100644
--- a/drivers/scsi/Makefile
+++ b/drivers/scsi/Makefile
@@ -122,21 +122,6 @@ obj-$(CONFIG_SCSI_LASI700)	+= 53c700.o lasi700.o
 obj-$(CONFIG_SCSI_NSP32)        += nsp32.o
 obj-$(CONFIG_SCSI_IPR)          += ipr.o
 obj-$(CONFIG_SCSI_IBMVSCSI)     += ibmvscsi/
-obj-$(CONFIG_SCSI_SATA_AHCI)    += libata.o ahci.o
-obj-$(CONFIG_SCSI_SATA_SVW)     += libata.o sata_svw.o
-obj-$(CONFIG_SCSI_ATA_PIIX)     += libata.o ata_piix.o
-obj-$(CONFIG_SCSI_SATA_PROMISE) += libata.o sata_promise.o
-obj-$(CONFIG_SCSI_SATA_QSTOR)   += libata.o sata_qstor.o
-obj-$(CONFIG_SCSI_SATA_SIL)     += libata.o sata_sil.o
-obj-$(CONFIG_SCSI_SATA_SIL24)   += libata.o sata_sil24.o
-obj-$(CONFIG_SCSI_SATA_VIA)     += libata.o sata_via.o
-obj-$(CONFIG_SCSI_SATA_VITESSE) += libata.o sata_vsc.o
-obj-$(CONFIG_SCSI_SATA_SIS)     += libata.o sata_sis.o
-obj-$(CONFIG_SCSI_SATA_SX4)     += libata.o sata_sx4.o
-obj-$(CONFIG_SCSI_SATA_NV)      += libata.o sata_nv.o
-obj-$(CONFIG_SCSI_SATA_ULI)     += libata.o sata_uli.o
-obj-$(CONFIG_SCSI_SATA_MV)      += libata.o sata_mv.o
-obj-$(CONFIG_SCSI_PDC_ADMA)     += libata.o pdc_adma.o
 obj-$(CONFIG_SCSI_HPTIOP)       += hptiop.o
 
 obj-$(CONFIG_ARM)               += arm/
@@ -166,7 +151,6 @@ ncr53c8xx-flags-$(CONFIG_SCSI_ZALON) \
 CFLAGS_ncr53c8xx.o      := $(ncr53c8xx-flags-y) $(ncr53c8xx-flags-m)
 zalon7xx-objs   := zalon.o ncr53c8xx.o
 NCR_Q720_mod-objs       := NCR_Q720.o ncr53c8xx.o
-libata-objs     := libata-core.o libata-scsi.o libata-bmdma.o libata-eh.o
 oktagon_esp_mod-objs    := oktagon_esp.o oktagon_io.o
 
 # Files generated that shall be removed upon make clean