20 files changed, 183 insertions, 101 deletions
diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c
index f1aaff6202a5..045bb4b823e1 100644
--- a/drivers/usb/core/devio.c
+++ b/drivers/usb/core/devio.c
@@ -965,10 +965,11 @@ static int proc_getdriver(struct dev_state *ps, void __user *arg)
 static int proc_connectinfo(struct dev_state *ps, void __user *arg)
 {
-        struct usbdevfs_connectinfo ci;
+        struct usbdevfs_connectinfo ci = {
+                .devnum = ps->dev->devnum,
+                .slow = ps->dev->speed == USB_SPEED_LOW
+        };
-        ci.devnum = ps->dev->devnum;
-        ci.slow = ps->dev->speed == USB_SPEED_LOW;
        if (copy_to_user(arg, &ci, sizeof(ci)))
                return -EFAULT;
        return 0;
diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig
index b739ca814651..607d0db4a988 100644
--- a/drivers/usb/gadget/Kconfig
+++ b/drivers/usb/gadget/Kconfig
@@ -158,7 +158,7 @@ config USB_GADGET_FSL_USB2
        boolean "Freescale Highspeed USB DR Peripheral Controller"
        depends on FSL_SOC || ARCH_MXC
        select USB_GADGET_DUALSPEED
-        select USB_FSL_MPH_DR_OF
+        select USB_FSL_MPH_DR_OF if OF
        help
           Some of Freescale PowerPC processors have a High Speed
           Dual-Role(DR) USB controller, which supports device mode.
diff --git a/drivers/usb/gadget/goku_udc.h b/drivers/usb/gadget/goku_udc.h
index 566cb2319056..e7e0c69d3b1f 100644
--- a/drivers/usb/gadget/goku_udc.h
+++ b/drivers/usb/gadget/goku_udc.h
@@ -251,7 +251,8 @@ struct goku_udc {
                                        got_region:1,
                                        req_config:1,
                                        configured:1,
-                                        enabled:1;
+                                        enabled:1,
+                                        registered:1;
        /* pci state used to access those endpoints */
        struct pci_dev                  *pdev;
diff --git a/drivers/usb/gadget/u_ether.c b/drivers/usb/gadget/u_ether.c
index cb23355f52d3..fbe86ca95802 100644
--- a/drivers/usb/gadget/u_ether.c
+++ b/drivers/usb/gadget/u_ether.c
@@ -811,7 +811,6 @@ int gether_setup(struct usb_gadget *g, u8 ethaddr[ETH_ALEN])
                INFO(dev, "MAC %pM\n", net->dev_addr);
                INFO(dev, "HOST MAC %pM\n", dev->host_mac);
-                netif_stop_queue(net);
                the_dev = dev;
        }
diff --git a/drivers/usb/gadget/u_serial.c b/drivers/usb/gadget/u_serial.c
index 01e5354a4c20..40f7716b31fc 100644
--- a/drivers/usb/gadget/u_serial.c
+++ b/drivers/usb/gadget/u_serial.c
@@ -105,11 +105,15 @@ struct gs_port {
        wait_queue_head_t       close_wait;     /* wait for last close */
        struct list_head        read_pool;
+        int read_started;
+        int read_allocated;
        struct list_head        read_queue;
        unsigned                n_read;
        struct tasklet_struct   push;
        struct list_head        write_pool;
+        int write_started;
+        int write_allocated;
        struct gs_buf           port_write_buf;
        wait_queue_head_t       drain_wait;     /* wait while writes drain */
@@ -363,6 +367,9 @@ __acquires(&port->port_lock)
                struct usb_request      *req;
                int                     len;
+                if (port->write_started >= QUEUE_SIZE)
+                        break;
                req = list_entry(pool->next, struct usb_request, list);
                len = gs_send_packet(port, req->buf, in->maxpacket);
                if (len == 0) {
@@ -397,6 +404,8 @@ __acquires(&port->port_lock)
                        break;
                }
+                port->write_started++;
                /* abort immediately after disconnect */
                if (!port->port_usb)
                        break;
@@ -418,7 +427,6 @@ __acquires(&port->port_lock)
 {
        struct list_head        *pool = &port->read_pool;
        struct usb_ep           *out = port->port_usb->out;
-        unsigned                started = 0;
        while (!list_empty(pool)) {
                struct usb_request      *req;
@@ -430,6 +438,9 @@ __acquires(&port->port_lock)
                if (!tty)
                        break;
+                if (port->read_started >= QUEUE_SIZE)
+                        break;
                req = list_entry(pool->next, struct usb_request, list);
                list_del(&req->list);
                req->length = out->maxpacket;
@@ -447,13 +458,13 @@ __acquires(&port->port_lock)
                        list_add(&req->list, pool);
                        break;
                }
-                started++;
+                port->read_started++;
                /* abort immediately after disconnect */
                if (!port->port_usb)
                        break;
        }
-        return started;
+        return port->read_started;
 }
 /*
@@ -535,6 +546,7 @@ static void gs_rx_push(unsigned long _port)
                }
 recycle:
                list_move(&req->list, &port->read_pool);
+                port->read_started--;
        }
        /* Push from tty to ldisc; without low_latency set this is handled by
@@ -587,6 +599,7 @@ static void gs_write_complete(struct usb_ep *ep, struct usb_request *req)
        spin_lock(&port->port_lock);
        list_add(&req->list, &port->write_pool);
+        port->write_started--;
        switch (req->status) {
        default:
@@ -608,7 +621,8 @@ static void gs_write_complete(struct usb_ep *ep, struct usb_request *req)
        spin_unlock(&port->port_lock);
 }
-static void gs_free_requests(struct usb_ep *ep, struct list_head *head)
+static void gs_free_requests(struct usb_ep *ep, struct list_head *head,
+                                                         int *allocated)
 {
        struct usb_request      *req;
@@ -616,25 +630,31 @@ static void gs_free_requests(struct usb_ep *ep, struct list_head *head)
                req = list_entry(head->next, struct usb_request, list);
                list_del(&req->list);
                gs_free_req(ep, req);
+                if (allocated)
+                        (*allocated)--;
        }
 }
 static int gs_alloc_requests(struct usb_ep *ep, struct list_head *head,
-                void (*fn)(struct usb_ep *, struct usb_request *))
+                void (*fn)(struct usb_ep *, struct usb_request *),
+                int *allocated)
 {
        int                     i;
        struct usb_request      *req;
+        int n = allocated ? QUEUE_SIZE - *allocated : QUEUE_SIZE;
        /* Pre-allocate up to QUEUE_SIZE transfers, but if we can't
         * do quite that many this time, don't fail ... we just won't
         * be as speedy as we might otherwise be.
         */
-        for (i = 0; i < QUEUE_SIZE; i++) {
+        for (i = 0; i < n; i++) {
                req = gs_alloc_req(ep, ep->maxpacket, GFP_ATOMIC);
                if (!req)
                        return list_empty(head) ? -ENOMEM : 0;
                req->complete = fn;
                list_add_tail(&req->list, head);
+                if (allocated)
+                        (*allocated)++;
        }
        return 0;
 }
@@ -661,14 +681,15 @@ static int gs_start_io(struct gs_port *port)
         * configurations may use different endpoints with a given port;
         * and high speed vs full speed changes packet sizes too.
         */
-        status = gs_alloc_requests(ep, head, gs_read_complete);
+        status = gs_alloc_requests(ep, head, gs_read_complete,
+                &port->read_allocated);
        if (status)
                return status;
        status = gs_alloc_requests(port->port_usb->in, &port->write_pool,
-                        gs_write_complete);
+                        gs_write_complete, &port->write_allocated);
        if (status) {
-                gs_free_requests(ep, head);
+                gs_free_requests(ep, head, &port->read_allocated);
                return status;
        }
@@ -680,8 +701,9 @@ static int gs_start_io(struct gs_port *port)
        if (started) {
                tty_wakeup(port->port_tty);
        } else {
-                gs_free_requests(ep, head);
+                gs_free_requests(ep, head, &port->read_allocated);
-                gs_free_requests(port->port_usb->in, &port->write_pool);
+                gs_free_requests(port->port_usb->in, &port->write_pool,
+                        &port->write_allocated);
                status = -EIO;
        }
@@ -1315,8 +1337,12 @@ void gserial_disconnect(struct gserial *gser)
        spin_lock_irqsave(&port->port_lock, flags);
        if (port->open_count == 0 && !port->openclose)
                gs_buf_free(&port->port_write_buf);
-        gs_free_requests(gser->out, &port->read_pool);
+        gs_free_requests(gser->out, &port->read_pool, NULL);
-        gs_free_requests(gser->out, &port->read_queue);
+        gs_free_requests(gser->out, &port->read_queue, NULL);
-        gs_free_requests(gser->in, &port->write_pool);
+        gs_free_requests(gser->in, &port->write_pool, NULL);
+        port->read_allocated = port->read_started =
+                port->write_allocated = port->write_started = 0;
        spin_unlock_irqrestore(&port->port_lock, flags);
 }
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 2391c396ca32..6f4f8e6a40c7 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -122,7 +122,7 @@ config USB_EHCI_FSL
        bool "Support for Freescale on-chip EHCI USB controller"
        depends on USB_EHCI_HCD && FSL_SOC
        select USB_EHCI_ROOT_HUB_TT
-        select USB_FSL_MPH_DR_OF
+        select USB_FSL_MPH_DR_OF if OF
        ---help---
          Variation of ARC USB block used in some Freescale chips.
diff --git a/drivers/usb/host/ehci-mxc.c b/drivers/usb/host/ehci-mxc.c
index ac9c4d7c44af..bce85055019a 100644
--- a/drivers/usb/host/ehci-mxc.c
+++ b/drivers/usb/host/ehci-mxc.c
@@ -36,6 +36,8 @@ struct ehci_mxc_priv {
 static int ehci_mxc_setup(struct usb_hcd *hcd)
 {
        struct ehci_hcd *ehci = hcd_to_ehci(hcd);
+        struct device *dev = hcd->self.controller;
+        struct mxc_usbh_platform_data *pdata = dev_get_platdata(dev);
        int retval;
        /* EHCI registers start at offset 0x100 */
@@ -63,6 +65,12 @@ static int ehci_mxc_setup(struct usb_hcd *hcd)
        ehci_reset(ehci);
+        /* set up the PORTSCx register */
+        ehci_writel(ehci, pdata->portsc, &ehci->regs->port_status[0]);
+        /* is this really needed? */
+        msleep(10);
        ehci_port_power(ehci, 0);
        return 0;
 }
@@ -114,7 +122,7 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev)
        struct mxc_usbh_platform_data *pdata = pdev->dev.platform_data;
        struct usb_hcd *hcd;
        struct resource *res;
-        int irq, ret, temp;
+        int irq, ret;
        struct ehci_mxc_priv *priv;
        struct device *dev = &pdev->dev;
@@ -188,10 +196,6 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev)
                clk_enable(priv->ahbclk);
        }
-        /* set up the PORTSCx register */
-        ehci_writel(ehci, pdata->portsc, &ehci->regs->port_status[0]);
-        mdelay(10);
        /* setup specific usb hw */
        ret = mxc_initialize_usb_hw(pdev->id, pdata->flags);
        if (ret < 0)
diff --git a/drivers/usb/host/ohci-jz4740.c b/drivers/usb/host/ohci-jz4740.c
index 10e1872f3ab9..931d588c3fb5 100644
--- a/drivers/usb/host/ohci-jz4740.c
+++ b/drivers/usb/host/ohci-jz4740.c
@@ -273,4 +273,4 @@ static struct platform_driver ohci_hcd_jz4740_driver = {
        },
 };
-MODULE_ALIAS("platfrom:jz4740-ohci");
+MODULE_ALIAS("platform:jz4740-ohci");
diff --git a/drivers/usb/misc/iowarrior.c b/drivers/usb/misc/iowarrior.c
index 375664198776..c9078e4e1f4d 100644
--- a/drivers/usb/misc/iowarrior.c
+++ b/drivers/usb/misc/iowarrior.c
@@ -553,6 +553,7 @@ static long iowarrior_ioctl(struct file *file, unsigned int cmd,
                        /* needed for power consumption */
                        struct usb_config_descriptor *cfg_descriptor = &dev->udev->actconfig->desc;
+                        memset(&info, 0, sizeof(info));
                        /* directly from the descriptor */
                        info.vendor = le16_to_cpu(dev->udev->descriptor.idVendor);
                        info.product = dev->product_id;
diff --git a/drivers/usb/misc/sisusbvga/sisusb.c b/drivers/usb/misc/sisusbvga/sisusb.c
index 70d00e99a4b4..dd573abd2d1e 100644
--- a/drivers/usb/misc/sisusbvga/sisusb.c
+++ b/drivers/usb/misc/sisusbvga/sisusb.c
@@ -3008,6 +3008,7 @@ sisusb_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
 #else
                        x.sisusb_conactive  = 0;
 #endif
+                        memset(x.sisusb_reserved, 0, sizeof(x.sisusb_reserved));
                        if (copy_to_user((void __user *)arg, &x, sizeof(x)))
                                retval = -EFAULT;
diff --git a/drivers/usb/musb/blackfin.c b/drivers/usb/musb/blackfin.c
index 611a9d274363..fcb5206a65bd 100644
--- a/drivers/usb/musb/blackfin.c
+++ b/drivers/usb/musb/blackfin.c
@@ -171,8 +171,9 @@ static irqreturn_t blackfin_interrupt(int irq, void *__hci)
        }
        /* Start sampling ID pin, when plug is removed from MUSB */
-        if (is_otg_enabled(musb) && (musb->xceiv->state == OTG_STATE_B_IDLE
+        if ((is_otg_enabled(musb) && (musb->xceiv->state == OTG_STATE_B_IDLE
-                || musb->xceiv->state == OTG_STATE_A_WAIT_BCON)) {
+                || musb->xceiv->state == OTG_STATE_A_WAIT_BCON)) ||
+                (musb->int_usb & MUSB_INTR_DISCONNECT && is_host_active(musb))) {
                mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY);
                musb->a_wait_bcon = TIMER_DELAY;
        }
@@ -323,30 +324,8 @@ int musb_platform_set_mode(struct musb *musb, u8 musb_mode)
        return -EIO;
 }
-int __init musb_platform_init(struct musb *musb, void *board_data)
+static void musb_platform_reg_init(struct musb *musb)
 {
-        /*
-         * Rev 1.0 BF549 EZ-KITs require PE7 to be high for both DEVICE
-         * and OTG HOST modes, while rev 1.1 and greater require PE7 to
-         * be low for DEVICE mode and high for HOST mode. We set it high
-         * here because we are in host mode
-         */
-        if (gpio_request(musb->config->gpio_vrsel, "USB_VRSEL")) {
-                printk(KERN_ERR "Failed ro request USB_VRSEL GPIO_%d \n",
-                        musb->config->gpio_vrsel);
-                return -ENODEV;
-        }
-        gpio_direction_output(musb->config->gpio_vrsel, 0);
-        usb_nop_xceiv_register();
-        musb->xceiv = otg_get_transceiver();
-        if (!musb->xceiv) {
-                gpio_free(musb->config->gpio_vrsel);
-                return -ENODEV;
-        }
        if (ANOMALY_05000346) {
                bfin_write_USB_APHY_CALIB(ANOMALY_05000346_value);
                SSYNC();
@@ -358,7 +337,8 @@ int __init musb_platform_init(struct musb *musb, void *board_data)
        }
        /* Configure PLL oscillator register */
-        bfin_write_USB_PLLOSC_CTRL(0x30a8);
+        bfin_write_USB_PLLOSC_CTRL(0x3080 |
+                        ((480/musb->config->clkin) << 1));
        SSYNC();
        bfin_write_USB_SRP_CLKDIV((get_sclk()/1000) / 32 - 1);
@@ -380,6 +360,33 @@ int __init musb_platform_init(struct musb *musb, void *board_data)
                                EP2_RX_ENA | EP3_RX_ENA | EP4_RX_ENA |
                                EP5_RX_ENA | EP6_RX_ENA | EP7_RX_ENA);
        SSYNC();
+}
+int __init musb_platform_init(struct musb *musb, void *board_data)
+{
+        /*
+         * Rev 1.0 BF549 EZ-KITs require PE7 to be high for both DEVICE
+         * and OTG HOST modes, while rev 1.1 and greater require PE7 to
+         * be low for DEVICE mode and high for HOST mode. We set it high
+         * here because we are in host mode
+         */
+        if (gpio_request(musb->config->gpio_vrsel, "USB_VRSEL")) {
+                printk(KERN_ERR "Failed ro request USB_VRSEL GPIO_%d\n",
+                        musb->config->gpio_vrsel);
+                return -ENODEV;
+        }
+        gpio_direction_output(musb->config->gpio_vrsel, 0);
+        usb_nop_xceiv_register();
+        musb->xceiv = otg_get_transceiver();
+        if (!musb->xceiv) {
+                gpio_free(musb->config->gpio_vrsel);
+                return -ENODEV;
+        }
+        musb_platform_reg_init(musb);
        if (is_host_enabled(musb)) {
                musb->board_set_vbus = bfin_set_vbus;
@@ -394,6 +401,27 @@ int __init musb_platform_init(struct musb *musb, void *board_data)
        return 0;
 }
+#ifdef CONFIG_PM
+void musb_platform_save_context(struct musb *musb,
+                        struct musb_context_registers *musb_context)
+{
+        if (is_host_active(musb))
+                /*
+                 * During hibernate gpio_vrsel will change from high to low
+                 * low which will generate wakeup event resume the system
+                 * immediately.  Set it to 0 before hibernate to avoid this
+                 * wakeup event.
+                 */
+                gpio_set_value(musb->config->gpio_vrsel, 0);
+}
+void musb_platform_restore_context(struct musb *musb,
+                        struct musb_context_registers *musb_context)
+{
+        musb_platform_reg_init(musb);
+}
+#endif
 int musb_platform_exit(struct musb *musb)
 {
        gpio_free(musb->config->gpio_vrsel);
diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c
index c9f9024c5515..e6669fc3b804 100644
--- a/drivers/usb/musb/musb_core.c
+++ b/drivers/usb/musb/musb_core.c
@@ -552,7 +552,8 @@ static irqreturn_t musb_stage0_irq(struct musb *musb, u8 int_usb,
        if (int_usb & MUSB_INTR_SESSREQ) {
                void __iomem *mbase = musb->mregs;
-                if (devctl & MUSB_DEVCTL_BDEVICE) {
+                if ((devctl & MUSB_DEVCTL_VBUS) == MUSB_DEVCTL_VBUS
+                                && (devctl & MUSB_DEVCTL_BDEVICE)) {
                        DBG(3, "SessReq while on B state\n");
                        return IRQ_HANDLED;
                }
@@ -1052,6 +1053,11 @@ static void musb_shutdown(struct platform_device *pdev)
                clk_put(musb->clock);
        spin_unlock_irqrestore(&musb->lock, flags);
+        if (!is_otg_enabled(musb) && is_host_enabled(musb))
+                usb_remove_hcd(musb_to_hcd(musb));
+        musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
+        musb_platform_exit(musb);
        /* FIXME power down */
 }
@@ -2244,13 +2250,6 @@ static int __exit musb_remove(struct platform_device *pdev)
         */
        musb_exit_debugfs(musb);
        musb_shutdown(pdev);
-#ifdef CONFIG_USB_MUSB_HDRC_HCD
-        if (musb->board_mode == MUSB_HOST)
-                usb_remove_hcd(musb_to_hcd(musb));
-#endif
-        musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
-        musb_platform_exit(musb);
-        musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
        musb_free(musb);
        iounmap(ctrl_base);
@@ -2411,9 +2410,6 @@ static int musb_suspend(struct device *dev)
        unsigned long   flags;
        struct musb     *musb = dev_to_musb(&pdev->dev);
-        if (!musb->clock)
-                return 0;
        spin_lock_irqsave(&musb->lock, flags);
        if (is_peripheral_active(musb)) {
@@ -2428,10 +2424,12 @@ static int musb_suspend(struct device *dev)
        musb_save_context(musb);
-        if (musb->set_clock)
+        if (musb->clock) {
-                musb->set_clock(musb->clock, 0);
+                if (musb->set_clock)
-        else
+                        musb->set_clock(musb->clock, 0);
-                clk_disable(musb->clock);
+                else
+                        clk_disable(musb->clock);
+        }
        spin_unlock_irqrestore(&musb->lock, flags);
        return 0;
 }
@@ -2441,13 +2439,12 @@ static int musb_resume_noirq(struct device *dev)
        struct platform_device *pdev = to_platform_device(dev);
        struct musb     *musb = dev_to_musb(&pdev->dev);
-        if (!musb->clock)
+        if (musb->clock) {
-                return 0;
+                if (musb->set_clock)
+                        musb->set_clock(musb->clock, 1);
-        if (musb->set_clock)
+                else
-                musb->set_clock(musb->clock, 1);
+                        clk_enable(musb->clock);
-        else
+        }
-                clk_enable(musb->clock);
        musb_restore_context(musb);
diff --git a/drivers/usb/musb/musb_core.h b/drivers/usb/musb/musb_core.h
index 69797e5b46a7..febaabcc2b35 100644
--- a/drivers/usb/musb/musb_core.h
+++ b/drivers/usb/musb/musb_core.h
@@ -487,7 +487,7 @@ struct musb_context_registers {
 };
 #if defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3) || \
-    defined(CONFIG_ARCH_OMAP4)
+    defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_BLACKFIN)
 extern void musb_platform_save_context(struct musb *musb,
                struct musb_context_registers *musb_context);
 extern void musb_platform_restore_context(struct musb *musb,
diff --git a/drivers/usb/musb/musb_gadget.c b/drivers/usb/musb/musb_gadget.c
index 5d815049cbaa..36cfd060dbe5 100644
--- a/drivers/usb/musb/musb_gadget.c
+++ b/drivers/usb/musb/musb_gadget.c
@@ -644,10 +644,8 @@ static void rxstate(struct musb *musb, struct musb_request *req)
         */
                                csr |= MUSB_RXCSR_DMAENAB;
-                                if (!musb_ep->hb_mult &&
-                                        musb_ep->hw_ep->rx_double_buffered)
-                                        csr |= MUSB_RXCSR_AUTOCLEAR;
 #ifdef USE_MODE1
+                                csr |= MUSB_RXCSR_AUTOCLEAR;
                                /* csr |= MUSB_RXCSR_DMAMODE; */
                                /* this special sequence (enabling and then
@@ -656,6 +654,10 @@ static void rxstate(struct musb *musb, struct musb_request *req)
                                 */
                                musb_writew(epio, MUSB_RXCSR,
                                        csr | MUSB_RXCSR_DMAMODE);
+#else
+                                if (!musb_ep->hb_mult &&
+                                        musb_ep->hw_ep->rx_double_buffered)
+                                        csr |= MUSB_RXCSR_AUTOCLEAR;
 #endif
                                musb_writew(epio, MUSB_RXCSR, csr);
@@ -807,7 +809,7 @@ void musb_g_rx(struct musb *musb, u8 epnum)
 #if defined(CONFIG_USB_INVENTRA_DMA) || defined(CONFIG_USB_TUSB_OMAP_DMA)
                /* Autoclear doesn't clear RxPktRdy for short packets */
-                if ((dma->desired_mode == 0)
+                if ((dma->desired_mode == 0 && !hw_ep->rx_double_buffered)
                                || (dma->actual_len
                                        & (musb_ep->packet_sz - 1))) {
                        /* ack the read! */
@@ -818,8 +820,16 @@ void musb_g_rx(struct musb *musb, u8 epnum)
                /* incomplete, and not short? wait for next IN packet */
                if ((request->actual < request->length)
                                && (musb_ep->dma->actual_len
-                                        == musb_ep->packet_sz))
+                                        == musb_ep->packet_sz)) {
+                        /* In double buffer case, continue to unload fifo if
+                         * there is Rx packet in FIFO.
+                         **/
+                        csr = musb_readw(epio, MUSB_RXCSR);
+                        if ((csr & MUSB_RXCSR_RXPKTRDY) &&
+                                hw_ep->rx_double_buffered)
+                                goto exit;
                        return;
+                }
 #endif
                musb_g_giveback(musb_ep, request, 0);
@@ -827,7 +837,7 @@ void musb_g_rx(struct musb *musb, u8 epnum)
                if (!request)
                        return;
        }
+exit:
        /* Analyze request */
        rxstate(musb, to_musb_request(request));
 }
@@ -916,13 +926,9 @@ static int musb_gadget_enable(struct usb_ep *ep,
                 * likewise high bandwidth periodic tx
                 */
                /* Set TXMAXP with the FIFO size of the endpoint
-                 * to disable double buffering mode. Currently, It seems that double
+                 * to disable double buffering mode.
-                 * buffering has problem if musb RTL revision number < 2.0.
                 */
-                if (musb->hwvers < MUSB_HWVERS_2000)
+                musb_writew(regs, MUSB_TXMAXP, musb_ep->packet_sz | (musb_ep->hb_mult << 11));
-                        musb_writew(regs, MUSB_TXMAXP, hw_ep->max_packet_sz_tx);
-                else
-                        musb_writew(regs, MUSB_TXMAXP, musb_ep->packet_sz | (musb_ep->hb_mult << 11));
                csr = MUSB_TXCSR_MODE | MUSB_TXCSR_CLRDATATOG;
                if (musb_readw(regs, MUSB_TXCSR)
@@ -958,10 +964,7 @@ static int musb_gadget_enable(struct usb_ep *ep,
                /* Set RXMAXP with the FIFO size of the endpoint
                 * to disable double buffering mode.
                 */
-                if (musb->hwvers < MUSB_HWVERS_2000)
+                musb_writew(regs, MUSB_RXMAXP, musb_ep->packet_sz | (musb_ep->hb_mult << 11));
-                        musb_writew(regs, MUSB_RXMAXP, hw_ep->max_packet_sz_rx);
-                else
-                        musb_writew(regs, MUSB_RXMAXP, musb_ep->packet_sz | (musb_ep->hb_mult << 11));
                /* force shared fifo to OUT-only mode */
                if (hw_ep->is_shared_fifo) {
@@ -1166,8 +1169,6 @@ static int musb_gadget_queue(struct usb_ep *ep, struct usb_request *req,
                                                : DMA_FROM_DEVICE);
                        request->mapped = 0;
                }
-        } else if (!req->buf) {
-                return -ENODATA;
        } else
                request->mapped = 0;
@@ -1695,8 +1696,10 @@ int __init musb_gadget_setup(struct musb *musb)
        musb_platform_try_idle(musb, 0);
        status = device_register(&musb->g.dev);
-        if (status != 0)
+        if (status != 0) {
+                put_device(&musb->g.dev);
                the_gadget = NULL;
+        }
        return status;
 }
diff --git a/drivers/usb/musb/musb_regs.h b/drivers/usb/musb/musb_regs.h
index 244267527a60..5a727c5b8676 100644
--- a/drivers/usb/musb/musb_regs.h
+++ b/drivers/usb/musb/musb_regs.h
@@ -633,8 +633,9 @@ static inline u8  musb_read_txhubaddr(void __iomem *mbase, u8 epnum)
        return 0;
 }
-static inline void  musb_read_txhubport(void __iomem *mbase, u8 epnum)
+static inline u8 musb_read_txhubport(void __iomem *mbase, u8 epnum)
 {
+        return 0;
 }
 #endif /* CONFIG_BLACKFIN */
diff --git a/drivers/usb/musb/musbhsdma.c b/drivers/usb/musb/musbhsdma.c
index 6f771af5cbdb..563114d613d6 100644
--- a/drivers/usb/musb/musbhsdma.c
+++ b/drivers/usb/musb/musbhsdma.c
@@ -158,6 +158,8 @@ static int dma_channel_program(struct dma_channel *channel,
                                dma_addr_t dma_addr, u32 len)
 {
        struct musb_dma_channel *musb_channel = channel->private_data;
+        struct musb_dma_controller *controller = musb_channel->controller;
+        struct musb *musb = controller->private_data;
        DBG(2, "ep%d-%s pkt_sz %d, dma_addr 0x%x length %d, mode %d\n",
                musb_channel->epnum,
@@ -167,6 +169,18 @@ static int dma_channel_program(struct dma_channel *channel,
        BUG_ON(channel->status == MUSB_DMA_STATUS_UNKNOWN ||
                channel->status == MUSB_DMA_STATUS_BUSY);
+        /*
+         * The DMA engine in RTL1.8 and above cannot handle
+         * DMA addresses that are not aligned to a 4 byte boundary.
+         * It ends up masking the last two bits of the address
+         * programmed in DMA_ADDR.
+         *
+         * Fail such DMA transfers, so that the backup PIO mode
+         * can carry out the transfer
+         */
+        if ((musb->hwvers >= MUSB_HWVERS_1800) && (dma_addr % 4))
+                return false;
        channel->actual_len = 0;
        musb_channel->start_addr = dma_addr;
        musb_channel->len = len;
diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 89a9a5847803..76f8b3556672 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -794,6 +794,8 @@ static struct usb_device_id id_table_combined [] = {
        { USB_DEVICE(FTDI_VID, FTDI_SCIENCESCOPE_LOGBOOKML_PID) },
        { USB_DEVICE(FTDI_VID, FTDI_SCIENCESCOPE_LS_LOGBOOK_PID) },
        { USB_DEVICE(FTDI_VID, FTDI_SCIENCESCOPE_HS_LOGBOOK_PID) },
+        { USB_DEVICE(QIHARDWARE_VID, MILKYMISTONE_JTAGSERIAL_PID),
+                .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
        { },                                    /* Optional parameter entry */
        { }                                     /* Terminating entry */
 };
diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h
index 7dfe02f1fb6a..263f62551197 100644
--- a/drivers/usb/serial/ftdi_sio_ids.h
+++ b/drivers/usb/serial/ftdi_sio_ids.h
@@ -1100,3 +1100,10 @@
 #define FTDI_SCIENCESCOPE_LOGBOOKML_PID         0xFF18
 #define FTDI_SCIENCESCOPE_LS_LOGBOOK_PID        0xFF1C
 #define FTDI_SCIENCESCOPE_HS_LOGBOOK_PID        0xFF1D
+/*
+ * Milkymist One JTAG/Serial
+ */
+#define QIHARDWARE_VID                  0x20B7
+#define MILKYMISTONE_JTAGSERIAL_PID     0x0713
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index 2297fb1bcf65..ef2977d3a613 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -518,7 +518,7 @@ static const struct usb_device_id option_ids[] = {
        { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K4505, 0xff, 0xff, 0xff) },
        { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K3765, 0xff, 0xff, 0xff) },
        { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_ETS1220, 0xff, 0xff, 0xff) },
-        { USB_DEVICE(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E14AC) },
+        { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E14AC, 0xff, 0xff, 0xff) },
        { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_V640) },
        { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_V620) },
        { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_V740) },
diff --git a/drivers/usb/storage/uas.c b/drivers/usb/storage/uas.c
index 2054b1e25a65..d1268191acbd 100644
--- a/drivers/usb/storage/uas.c
+++ b/drivers/usb/storage/uas.c
@@ -331,10 +331,7 @@ static struct urb *uas_alloc_cmd_urb(struct uas_dev_info *devinfo, gfp_t gfp,
        iu->iu_id = IU_ID_COMMAND;
        iu->tag = cpu_to_be16(stream_id);
-        if (sdev->ordered_tags && (cmnd->request->cmd_flags & REQ_HARDBARRIER))
+        iu->prio_attr = UAS_SIMPLE_TAG;
-                iu->prio_attr = UAS_ORDERED_TAG;
-        else
-                iu->prio_attr = UAS_SIMPLE_TAG;
        iu->len = len;
        int_to_scsilun(sdev->lun, &iu->lun);
        memcpy(iu->cdb, cmnd->cmnd, cmnd->cmd_len);