1 files changed, 0 insertions, 141 deletions

diff --git a/drivers/usb/otg/Kconfig b/drivers/usb/otg/Kconfig
deleted file mode 100644
index 37962c99ff1e..000000000000
--- a/drivers/usb/otg/Kconfig
+++ /dev/null
@@ -1,141 +0,0 @@
-#
-# USB OTG infrastructure may be needed for peripheral-only, host-only,
-# or OTG-capable configurations when OTG transceivers or controllers
-# are used.
-#
-
-comment "OTG and related infrastructure"
-
-config USB_OTG_UTILS
-        bool
-        help
-          Select this to make sure the build includes objects from
-          the OTG infrastructure directory.
-
-if USB || USB_GADGET
-
-#
-# USB Transceiver Drivers
-#
-config USB_GPIO_VBUS
-        tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
-        depends on GENERIC_GPIO
-        select USB_OTG_UTILS
-        help
-          Provides simple GPIO VBUS sensing for controllers with an
-          internal transceiver via the usb_phy interface, and
-          optionally control of a D+ pullup GPIO as well as a VBUS
-          current limit regulator.
-
-config ISP1301_OMAP
-        tristate "Philips ISP1301 with OMAP OTG"
-        depends on I2C && ARCH_OMAP_OTG
-        select USB_OTG_UTILS
-        help
-          If you say yes here you get support for the Philips ISP1301
-          USB-On-The-Go transceiver working with the OMAP OTG controller.
-          The ISP1301 is a full speed USB  transceiver which is used in
-          products including H2, H3, and H4 development boards for Texas
-          Instruments OMAP processors.
-
-          This driver can also be built as a module.  If so, the module
-          will be called isp1301_omap.
-
-config USB_ULPI
-        bool "Generic ULPI Transceiver Driver"
-        depends on ARM
-        select USB_OTG_UTILS
-        help
-          Enable this to support ULPI connected USB OTG transceivers which
-          are likely found on embedded boards.
-
-config USB_ULPI_VIEWPORT
-        bool
-        depends on USB_ULPI
-        help
-          Provides read/write operations to the ULPI phy register set for
-          controllers with a viewport register (e.g. Chipidea/ARC controllers).
-
-config TWL4030_USB
-        tristate "TWL4030 USB Transceiver Driver"
-        depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS
-        select USB_OTG_UTILS
-        help
-          Enable this to support the USB OTG transceiver on TWL4030
-          family chips (including the TWL5030 and TPS659x0 devices).
-          This transceiver supports high and full speed devices plus,
-          in host mode, low speed.
-
-config TWL6030_USB
-        tristate "TWL6030 USB Transceiver Driver"
-        depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
-        select USB_OTG_UTILS
-        help
-          Enable this to support the USB OTG transceiver on TWL6030
-          family chips. This TWL6030 transceiver has the VBUS and ID GND
-          and OTG SRP events capabilities. For all other transceiver functionality
-          UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
-          are hooked to this driver through platform_data structure.
-          The definition of internal PHY APIs are in the mach-omap2 layer.
-
-config NOP_USB_XCEIV
-        tristate "NOP USB Transceiver Driver"
-        select USB_OTG_UTILS
-        help
-          This driver is to be used by all the usb transceiver which are either
-          built-in with usb ip or which are autonomous and doesn't require any
-          phy programming such as ISP1x04 etc.
-
-config USB_MSM_OTG
-        tristate "OTG support for Qualcomm on-chip USB controller"
-        depends on (USB || USB_GADGET) && ARCH_MSM
-        select USB_OTG_UTILS
-        help
-          Enable this to support the USB OTG transceiver on MSM chips. It
-          handles PHY initialization, clock management, and workarounds
-          required after resetting the hardware and power management.
-          This driver is required even for peripheral only or host only
-          mode configurations.
-          This driver is not supported on boards like trout which
-          has an external PHY.
-
-config AB8500_USB
-        tristate "AB8500 USB Transceiver Driver"
-        depends on AB8500_CORE
-        select USB_OTG_UTILS
-        help
-          Enable this to support the USB OTG transceiver in AB8500 chip.
-          This transceiver supports high and full speed devices plus,
-          in host mode, low speed.
-
-config FSL_USB2_OTG
-        bool "Freescale USB OTG Transceiver Driver"
-        depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_SUSPEND
-        select USB_OTG
-        select USB_OTG_UTILS
-        help
-          Enable this to support Freescale USB OTG transceiver.
-
-config USB_MXS_PHY
-        tristate "Freescale MXS USB PHY support"
-        depends on ARCH_MXC || ARCH_MXS
-        select STMP_DEVICE
-        select USB_OTG_UTILS
-        help
-          Enable this to support the Freescale MXS USB PHY.
-
-          MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
-
-config USB_MV_OTG
-        tristate "Marvell USB OTG support"
-        depends on USB_EHCI_MV && USB_MV_UDC && USB_SUSPEND
-        select USB_OTG
-        select USB_OTG_UTILS
-        help
-          Say Y here if you want to build Marvell USB OTG transciever
-          driver in kernel (including PXA and MMP series). This driver
-          implements role switch between EHCI host driver and gadget driver.
-
-          To compile this driver as a module, choose M here.
-
-endif # USB || OTG