1 files changed, 171 insertions, 2 deletions

diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c
index 202770676da3..1d0f45f0e7a6 100644
--- a/drivers/usb/host/xhci-mem.c
+++ b/drivers/usb/host/xhci-mem.c
@@ -1045,7 +1045,7 @@ static inline u32 xhci_get_max_esit_payload(struct xhci_hcd *xhci,
         if (udev->speed == USB_SPEED_SUPER)
                 return ep->ss_ep_comp.wBytesPerInterval;
 
-        max_packet = ep->desc.wMaxPacketSize & 0x3ff;
+        max_packet = GET_MAX_PACKET(ep->desc.wMaxPacketSize);
         max_burst = (ep->desc.wMaxPacketSize & 0x1800) >> 11;
         /* A 0 in max burst means 1 transfer per ESIT */
         return max_packet * (max_burst + 1);
@@ -1135,7 +1135,7 @@ int xhci_endpoint_init(struct xhci_hcd *xhci,
                 /* Fall through */
         case USB_SPEED_FULL:
         case USB_SPEED_LOW:
-                max_packet = ep->desc.wMaxPacketSize & 0x3ff;
+                max_packet = GET_MAX_PACKET(ep->desc.wMaxPacketSize);
                 ep_ctx->ep_info2 |= MAX_PACKET(max_packet);
                 break;
         default:
@@ -1443,6 +1443,13 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci)
         xhci->dcbaa = NULL;
 
         scratchpad_free(xhci);
+
+        xhci->num_usb2_ports = 0;
+        xhci->num_usb3_ports = 0;
+        kfree(xhci->usb2_ports);
+        kfree(xhci->usb3_ports);
+        kfree(xhci->port_array);
+
         xhci->page_size = 0;
         xhci->page_shift = 0;
         xhci->bus_suspended = 0;
@@ -1627,6 +1634,166 @@ static void xhci_set_hc_event_deq(struct xhci_hcd *xhci)
                         &xhci->ir_set->erst_dequeue);
 }
 
+static void xhci_add_in_port(struct xhci_hcd *xhci, unsigned int num_ports,
+                u32 __iomem *addr, u8 major_revision)
+{
+        u32 temp, port_offset, port_count;
+        int i;
+
+        if (major_revision > 0x03) {
+                xhci_warn(xhci, "Ignoring unknown port speed, "
+                                "Ext Cap %p, revision = 0x%x\n",
+                                addr, major_revision);
+                /* Ignoring port protocol we can't understand. FIXME */
+                return;
+        }
+
+        /* Port offset and count in the third dword, see section 7.2 */
+        temp = xhci_readl(xhci, addr + 2);
+        port_offset = XHCI_EXT_PORT_OFF(temp);
+        port_count = XHCI_EXT_PORT_COUNT(temp);
+        xhci_dbg(xhci, "Ext Cap %p, port offset = %u, "
+                        "count = %u, revision = 0x%x\n",
+                        addr, port_offset, port_count, major_revision);
+        /* Port count includes the current port offset */
+        if (port_offset == 0 || (port_offset + port_count - 1) > num_ports)
+                /* WTF? "Valid values are ‘1’ to MaxPorts" */
+                return;
+        port_offset--;
+        for (i = port_offset; i < (port_offset + port_count); i++) {
+                /* Duplicate entry.  Ignore the port if the revisions differ. */
+                if (xhci->port_array[i] != 0) {
+                        xhci_warn(xhci, "Duplicate port entry, Ext Cap %p,"
+                                        " port %u\n", addr, i);
+                        xhci_warn(xhci, "Port was marked as USB %u, "
+                                        "duplicated as USB %u\n",
+                                        xhci->port_array[i], major_revision);
+                        /* Only adjust the roothub port counts if we haven't
+                         * found a similar duplicate.
+                         */
+                        if (xhci->port_array[i] != major_revision &&
+                                xhci->port_array[i] != (u8) -1) {
+                                if (xhci->port_array[i] == 0x03)
+                                        xhci->num_usb3_ports--;
+                                else
+                                        xhci->num_usb2_ports--;
+                                xhci->port_array[i] = (u8) -1;
+                        }
+                        /* FIXME: Should we disable the port? */
+                        continue;
+                }
+                xhci->port_array[i] = major_revision;
+                if (major_revision == 0x03)
+                        xhci->num_usb3_ports++;
+                else
+                        xhci->num_usb2_ports++;
+        }
+        /* FIXME: Should we disable ports not in the Extended Capabilities? */
+}
+
+/*
+ * Scan the Extended Capabilities for the "Supported Protocol Capabilities" that
+ * specify what speeds each port is supposed to be.  We can't count on the port
+ * speed bits in the PORTSC register being correct until a device is connected,
+ * but we need to set up the two fake roothubs with the correct number of USB
+ * 3.0 and USB 2.0 ports at host controller initialization time.
+ */
+static int xhci_setup_port_arrays(struct xhci_hcd *xhci, gfp_t flags)
+{
+        u32 __iomem *addr;
+        u32 offset;
+        unsigned int num_ports;
+        int i, port_index;
+
+        addr = &xhci->cap_regs->hcc_params;
+        offset = XHCI_HCC_EXT_CAPS(xhci_readl(xhci, addr));
+        if (offset == 0) {
+                xhci_err(xhci, "No Extended Capability registers, "
+                                "unable to set up roothub.\n");
+                return -ENODEV;
+        }
+
+        num_ports = HCS_MAX_PORTS(xhci->hcs_params1);
+        xhci->port_array = kzalloc(sizeof(*xhci->port_array)*num_ports, flags);
+        if (!xhci->port_array)
+                return -ENOMEM;
+
+        /*
+         * For whatever reason, the first capability offset is from the
+         * capability register base, not from the HCCPARAMS register.
+         * See section 5.3.6 for offset calculation.
+         */
+        addr = &xhci->cap_regs->hc_capbase + offset;
+        while (1) {
+                u32 cap_id;
+
+                cap_id = xhci_readl(xhci, addr);
+                if (XHCI_EXT_CAPS_ID(cap_id) == XHCI_EXT_CAPS_PROTOCOL)
+                        xhci_add_in_port(xhci, num_ports, addr,
+                                        (u8) XHCI_EXT_PORT_MAJOR(cap_id));
+                offset = XHCI_EXT_CAPS_NEXT(cap_id);
+                if (!offset || (xhci->num_usb2_ports + xhci->num_usb3_ports)
+                                == num_ports)
+                        break;
+                /*
+                 * Once you're into the Extended Capabilities, the offset is
+                 * always relative to the register holding the offset.
+                 */
+                addr += offset;
+        }
+
+        if (xhci->num_usb2_ports == 0 && xhci->num_usb3_ports == 0) {
+                xhci_warn(xhci, "No ports on the roothubs?\n");
+                return -ENODEV;
+        }
+        xhci_dbg(xhci, "Found %u USB 2.0 ports and %u USB 3.0 ports.\n",
+                        xhci->num_usb2_ports, xhci->num_usb3_ports);
+        /*
+         * Note we could have all USB 3.0 ports, or all USB 2.0 ports.
+         * Not sure how the USB core will handle a hub with no ports...
+         */
+        if (xhci->num_usb2_ports) {
+                xhci->usb2_ports = kmalloc(sizeof(*xhci->usb2_ports)*
+                                xhci->num_usb2_ports, flags);
+                if (!xhci->usb2_ports)
+                        return -ENOMEM;
+
+                port_index = 0;
+                for (i = 0; i < num_ports; i++) {
+                        if (xhci->port_array[i] == 0x03 ||
+                                        xhci->port_array[i] == 0 ||
+                                        xhci->port_array[i] == -1)
+                                continue;
+
+                        xhci->usb2_ports[port_index] =
+                                &xhci->op_regs->port_status_base +
+                                NUM_PORT_REGS*i;
+                        xhci_dbg(xhci, "USB 2.0 port at index %u, "
+                                        "addr = %p\n", i,
+                                        xhci->usb2_ports[port_index]);
+                        port_index++;
+                }
+        }
+        if (xhci->num_usb3_ports) {
+                xhci->usb3_ports = kmalloc(sizeof(*xhci->usb3_ports)*
+                                xhci->num_usb3_ports, flags);
+                if (!xhci->usb3_ports)
+                        return -ENOMEM;
+
+                port_index = 0;
+                for (i = 0; i < num_ports; i++)
+                        if (xhci->port_array[i] == 0x03) {
+                                xhci->usb3_ports[port_index] =
+                                        &xhci->op_regs->port_status_base +
+                                        NUM_PORT_REGS*i;
+                                xhci_dbg(xhci, "USB 3.0 port at index %u, "
+                                                "addr = %p\n", i,
+                                                xhci->usb3_ports[port_index]);
+                                port_index++;
+                        }
+        }
+        return 0;
+}
 
 int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags)
 {
@@ -1809,6 +1976,8 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags)
 
         if (scratchpad_alloc(xhci, flags))
                 goto fail;
+        if (xhci_setup_port_arrays(xhci, flags))
+                goto fail;
 
         return 0;