1 files changed, 281 insertions, 0 deletions

diff --git a/drivers/tty/serial/ip22zilog.h b/drivers/tty/serial/ip22zilog.h
new file mode 100644
index 000000000000..a59a9a8341d2
--- /dev/null
+++ b/drivers/tty/serial/ip22zilog.h
@@ -0,0 +1,281 @@
+#ifndef _IP22_ZILOG_H
+#define _IP22_ZILOG_H
+
+#include <asm/byteorder.h>
+
+struct zilog_channel {
+#ifdef __BIG_ENDIAN
+        volatile unsigned char unused0[3];
+        volatile unsigned char control;
+        volatile unsigned char unused1[3];
+        volatile unsigned char data;
+#else /* __LITTLE_ENDIAN */
+        volatile unsigned char control;
+        volatile unsigned char unused0[3];
+        volatile unsigned char data;
+        volatile unsigned char unused1[3];
+#endif
+};
+
+struct zilog_layout {
+        struct zilog_channel channelB;
+        struct zilog_channel channelA;
+};
+
+#define NUM_ZSREGS    16
+
+/* Conversion routines to/from brg time constants from/to bits
+ * per second.
+ */
+#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
+#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
+
+/* The Zilog register set */
+
+#define FLAG    0x7e
+
+/* Write Register 0 */
+#define R0      0               /* Register selects */
+#define R1      1
+#define R2      2
+#define R3      3
+#define R4      4
+#define R5      5
+#define R6      6
+#define R7      7
+#define R8      8
+#define R9      9
+#define R10     10
+#define R11     11
+#define R12     12
+#define R13     13
+#define R14     14
+#define R15     15
+
+#define NULLCODE        0       /* Null Code */
+#define POINT_HIGH      0x8     /* Select upper half of registers */
+#define RES_EXT_INT     0x10    /* Reset Ext. Status Interrupts */
+#define SEND_ABORT      0x18    /* HDLC Abort */
+#define RES_RxINT_FC    0x20    /* Reset RxINT on First Character */
+#define RES_Tx_P        0x28    /* Reset TxINT Pending */
+#define ERR_RES         0x30    /* Error Reset */
+#define RES_H_IUS       0x38    /* Reset highest IUS */
+
+#define RES_Rx_CRC      0x40    /* Reset Rx CRC Checker */
+#define RES_Tx_CRC      0x80    /* Reset Tx CRC Checker */
+#define RES_EOM_L       0xC0    /* Reset EOM latch */
+
+/* Write Register 1 */
+
+#define EXT_INT_ENAB    0x1     /* Ext Int Enable */
+#define TxINT_ENAB      0x2     /* Tx Int Enable */
+#define PAR_SPEC        0x4     /* Parity is special condition */
+
+#define RxINT_DISAB     0       /* Rx Int Disable */
+#define RxINT_FCERR     0x8     /* Rx Int on First Character Only or Error */
+#define INT_ALL_Rx      0x10    /* Int on all Rx Characters or error */
+#define INT_ERR_Rx      0x18    /* Int on error only */
+#define RxINT_MASK      0x18
+
+#define WT_RDY_RT       0x20    /* Wait/Ready on R/T */
+#define WT_FN_RDYFN     0x40    /* Wait/FN/Ready FN */
+#define WT_RDY_ENAB     0x80    /* Wait/Ready Enable */
+
+/* Write Register #2 (Interrupt Vector) */
+
+/* Write Register 3 */
+
+#define RxENAB          0x1     /* Rx Enable */
+#define SYNC_L_INH      0x2     /* Sync Character Load Inhibit */
+#define ADD_SM          0x4     /* Address Search Mode (SDLC) */
+#define RxCRC_ENAB      0x8     /* Rx CRC Enable */
+#define ENT_HM          0x10    /* Enter Hunt Mode */
+#define AUTO_ENAB       0x20    /* Auto Enables */
+#define Rx5             0x0     /* Rx 5 Bits/Character */
+#define Rx7             0x40    /* Rx 7 Bits/Character */
+#define Rx6             0x80    /* Rx 6 Bits/Character */
+#define Rx8             0xc0    /* Rx 8 Bits/Character */
+#define RxN_MASK        0xc0
+
+/* Write Register 4 */
+
+#define PAR_ENAB        0x1     /* Parity Enable */
+#define PAR_EVEN        0x2     /* Parity Even/Odd* */
+
+#define SYNC_ENAB       0       /* Sync Modes Enable */
+#define SB1             0x4     /* 1 stop bit/char */
+#define SB15            0x8     /* 1.5 stop bits/char */
+#define SB2             0xc     /* 2 stop bits/char */
+
+#define MONSYNC         0       /* 8 Bit Sync character */
+#define BISYNC          0x10    /* 16 bit sync character */
+#define SDLC            0x20    /* SDLC Mode (01111110 Sync Flag) */
+#define EXTSYNC         0x30    /* External Sync Mode */
+
+#define X1CLK           0x0     /* x1 clock mode */
+#define X16CLK          0x40    /* x16 clock mode */
+#define X32CLK          0x80    /* x32 clock mode */
+#define X64CLK          0xC0    /* x64 clock mode */
+#define XCLK_MASK       0xC0
+
+/* Write Register 5 */
+
+#define TxCRC_ENAB      0x1     /* Tx CRC Enable */
+#define RTS             0x2     /* RTS */
+#define SDLC_CRC        0x4     /* SDLC/CRC-16 */
+#define TxENAB          0x8     /* Tx Enable */
+#define SND_BRK         0x10    /* Send Break */
+#define Tx5             0x0     /* Tx 5 bits (or less)/character */
+#define Tx7             0x20    /* Tx 7 bits/character */
+#define Tx6             0x40    /* Tx 6 bits/character */
+#define Tx8             0x60    /* Tx 8 bits/character */
+#define TxN_MASK        0x60
+#define DTR             0x80    /* DTR */
+
+/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
+
+/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
+
+/* Write Register 8 (transmit buffer) */
+
+/* Write Register 9 (Master interrupt control) */
+#define VIS     1       /* Vector Includes Status */
+#define NV      2       /* No Vector */
+#define DLC     4       /* Disable Lower Chain */
+#define MIE     8       /* Master Interrupt Enable */
+#define STATHI  0x10    /* Status high */
+#define NORESET 0       /* No reset on write to R9 */
+#define CHRB    0x40    /* Reset channel B */
+#define CHRA    0x80    /* Reset channel A */
+#define FHWRES  0xc0    /* Force hardware reset */
+
+/* Write Register 10 (misc control bits) */
+#define BIT6    1       /* 6 bit/8bit sync */
+#define LOOPMODE 2      /* SDLC Loop mode */
+#define ABUNDER 4       /* Abort/flag on SDLC xmit underrun */
+#define MARKIDLE 8      /* Mark/flag on idle */
+#define GAOP    0x10    /* Go active on poll */
+#define NRZ     0       /* NRZ mode */
+#define NRZI    0x20    /* NRZI mode */
+#define FM1     0x40    /* FM1 (transition = 1) */
+#define FM0     0x60    /* FM0 (transition = 0) */
+#define CRCPS   0x80    /* CRC Preset I/O */
+
+/* Write Register 11 (Clock Mode control) */
+#define TRxCXT  0       /* TRxC = Xtal output */
+#define TRxCTC  1       /* TRxC = Transmit clock */
+#define TRxCBR  2       /* TRxC = BR Generator Output */
+#define TRxCDP  3       /* TRxC = DPLL output */
+#define TRxCOI  4       /* TRxC O/I */
+#define TCRTxCP 0       /* Transmit clock = RTxC pin */
+#define TCTRxCP 8       /* Transmit clock = TRxC pin */
+#define TCBR    0x10    /* Transmit clock = BR Generator output */
+#define TCDPLL  0x18    /* Transmit clock = DPLL output */
+#define RCRTxCP 0       /* Receive clock = RTxC pin */
+#define RCTRxCP 0x20    /* Receive clock = TRxC pin */
+#define RCBR    0x40    /* Receive clock = BR Generator output */
+#define RCDPLL  0x60    /* Receive clock = DPLL output */
+#define RTxCX   0x80    /* RTxC Xtal/No Xtal */
+
+/* Write Register 12 (lower byte of baud rate generator time constant) */
+
+/* Write Register 13 (upper byte of baud rate generator time constant) */
+
+/* Write Register 14 (Misc control bits) */
+#define BRENAB  1       /* Baud rate generator enable */
+#define BRSRC   2       /* Baud rate generator source */
+#define DTRREQ  4       /* DTR/Request function */
+#define AUTOECHO 8      /* Auto Echo */
+#define LOOPBAK 0x10    /* Local loopback */
+#define SEARCH  0x20    /* Enter search mode */
+#define RMC     0x40    /* Reset missing clock */
+#define DISDPLL 0x60    /* Disable DPLL */
+#define SSBR    0x80    /* Set DPLL source = BR generator */
+#define SSRTxC  0xa0    /* Set DPLL source = RTxC */
+#define SFMM    0xc0    /* Set FM mode */
+#define SNRZI   0xe0    /* Set NRZI mode */
+
+/* Write Register 15 (external/status interrupt control) */
+#define ZCIE    2       /* Zero count IE */
+#define DCDIE   8       /* DCD IE */
+#define SYNCIE  0x10    /* Sync/hunt IE */
+#define CTSIE   0x20    /* CTS IE */
+#define TxUIE   0x40    /* Tx Underrun/EOM IE */
+#define BRKIE   0x80    /* Break/Abort IE */
+
+
+/* Read Register 0 */
+#define Rx_CH_AV        0x1     /* Rx Character Available */
+#define ZCOUNT          0x2     /* Zero count */
+#define Tx_BUF_EMP      0x4     /* Tx Buffer empty */
+#define DCD             0x8     /* DCD */
+#define SYNC            0x10    /* Sync/hunt */
+#define CTS             0x20    /* CTS */
+#define TxEOM           0x40    /* Tx underrun */
+#define BRK_ABRT        0x80    /* Break/Abort */
+
+/* Read Register 1 */
+#define ALL_SNT         0x1     /* All sent */
+/* Residue Data for 8 Rx bits/char programmed */
+#define RES3            0x8     /* 0/3 */
+#define RES4            0x4     /* 0/4 */
+#define RES5            0xc     /* 0/5 */
+#define RES6            0x2     /* 0/6 */
+#define RES7            0xa     /* 0/7 */
+#define RES8            0x6     /* 0/8 */
+#define RES18           0xe     /* 1/8 */
+#define RES28           0x0     /* 2/8 */
+/* Special Rx Condition Interrupts */
+#define PAR_ERR         0x10    /* Parity error */
+#define Rx_OVR          0x20    /* Rx Overrun Error */
+#define CRC_ERR         0x40    /* CRC/Framing Error */
+#define END_FR          0x80    /* End of Frame (SDLC) */
+
+/* Read Register 2 (channel b only) - Interrupt vector */
+#define CHB_Tx_EMPTY    0x00
+#define CHB_EXT_STAT    0x02
+#define CHB_Rx_AVAIL    0x04
+#define CHB_SPECIAL     0x06
+#define CHA_Tx_EMPTY    0x08
+#define CHA_EXT_STAT    0x0a
+#define CHA_Rx_AVAIL    0x0c
+#define CHA_SPECIAL     0x0e
+#define STATUS_MASK     0x0e
+
+/* Read Register 3 (interrupt pending register) ch a only */
+#define CHBEXT  0x1             /* Channel B Ext/Stat IP */
+#define CHBTxIP 0x2             /* Channel B Tx IP */
+#define CHBRxIP 0x4             /* Channel B Rx IP */
+#define CHAEXT  0x8             /* Channel A Ext/Stat IP */
+#define CHATxIP 0x10            /* Channel A Tx IP */
+#define CHARxIP 0x20            /* Channel A Rx IP */
+
+/* Read Register 8 (receive data register) */
+
+/* Read Register 10  (misc status bits) */
+#define ONLOOP  2               /* On loop */
+#define LOOPSEND 0x10           /* Loop sending */
+#define CLK2MIS 0x40            /* Two clocks missing */
+#define CLK1MIS 0x80            /* One clock missing */
+
+/* Read Register 12 (lower byte of baud rate generator constant) */
+
+/* Read Register 13 (upper byte of baud rate generator constant) */
+
+/* Read Register 15 (value of WR 15) */
+
+/* Misc macros */
+#define ZS_CLEARERR(channel)    do { writeb(ERR_RES, &channel->control); \
+                                     udelay(5); } while(0)
+
+#define ZS_CLEARSTAT(channel)   do { writeb(RES_EXT_INT, &channel->control); \
+                                     udelay(5); } while(0)
+
+#define ZS_CLEARFIFO(channel)   do { readb(&channel->data); \
+                                     udelay(2); \
+                                     readb(&channel->data); \
+                                     udelay(2); \
+                                     readb(&channel->data); \
+                                     udelay(2); } while(0)
+
+#endif /* _IP22_ZILOG_H */