aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/tty/serial/68360serial.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/tty/serial/68360serial.c')
-rw-r--r--drivers/tty/serial/68360serial.c2978
1 files changed, 2978 insertions, 0 deletions
diff --git a/drivers/tty/serial/68360serial.c b/drivers/tty/serial/68360serial.c
new file mode 100644
index 000000000000..88b13356ec10
--- /dev/null
+++ b/drivers/tty/serial/68360serial.c
@@ -0,0 +1,2978 @@
1/*
2 * UART driver for 68360 CPM SCC or SMC
3 * Copyright (c) 2000 D. Jeff Dionne <jeff@uclinux.org>,
4 * Copyright (c) 2000 Michael Leslie <mleslie@lineo.ca>
5 * Copyright (c) 1997 Dan Malek <dmalek@jlc.net>
6 *
7 * I used the serial.c driver as the framework for this driver.
8 * Give credit to those guys.
9 * The original code was written for the MBX860 board. I tried to make
10 * it generic, but there may be some assumptions in the structures that
11 * have to be fixed later.
12 * To save porting time, I did not bother to change any object names
13 * that are not accessed outside of this file.
14 * It still needs lots of work........When it was easy, I included code
15 * to support the SCCs, but this has never been tested, nor is it complete.
16 * Only the SCCs support modem control, so that is not complete either.
17 *
18 * This module exports the following rs232 io functions:
19 *
20 * int rs_360_init(void);
21 */
22
23#include <linux/module.h>
24#include <linux/errno.h>
25#include <linux/signal.h>
26#include <linux/sched.h>
27#include <linux/timer.h>
28#include <linux/interrupt.h>
29#include <linux/tty.h>
30#include <linux/tty_flip.h>
31#include <linux/serial.h>
32#include <linux/serialP.h>
33#include <linux/major.h>
34#include <linux/string.h>
35#include <linux/fcntl.h>
36#include <linux/ptrace.h>
37#include <linux/mm.h>
38#include <linux/init.h>
39#include <linux/delay.h>
40#include <asm/irq.h>
41#include <asm/m68360.h>
42#include <asm/commproc.h>
43
44
45#ifdef CONFIG_KGDB
46extern void breakpoint(void);
47extern void set_debug_traps(void);
48extern int kgdb_output_string (const char* s, unsigned int count);
49#endif
50
51
52/* #ifdef CONFIG_SERIAL_CONSOLE */ /* This seems to be a post 2.0 thing - mles */
53#include <linux/console.h>
54#include <linux/jiffies.h>
55
56/* this defines the index into rs_table for the port to use
57 */
58#ifndef CONFIG_SERIAL_CONSOLE_PORT
59#define CONFIG_SERIAL_CONSOLE_PORT 1 /* ie SMC2 - note USE_SMC2 must be defined */
60#endif
61/* #endif */
62
63#if 0
64/* SCC2 for console
65 */
66#undef CONFIG_SERIAL_CONSOLE_PORT
67#define CONFIG_SERIAL_CONSOLE_PORT 2
68#endif
69
70
71#define TX_WAKEUP ASYNC_SHARE_IRQ
72
73static char *serial_name = "CPM UART driver";
74static char *serial_version = "0.03";
75
76static struct tty_driver *serial_driver;
77int serial_console_setup(struct console *co, char *options);
78
79/*
80 * Serial driver configuration section. Here are the various options:
81 */
82#define SERIAL_PARANOIA_CHECK
83#define CONFIG_SERIAL_NOPAUSE_IO
84#define SERIAL_DO_RESTART
85
86/* Set of debugging defines */
87
88#undef SERIAL_DEBUG_INTR
89#undef SERIAL_DEBUG_OPEN
90#undef SERIAL_DEBUG_FLOW
91#undef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT
92
93#define _INLINE_ inline
94
95#define DBG_CNT(s)
96
97/* We overload some of the items in the data structure to meet our
98 * needs. For example, the port address is the CPM parameter ram
99 * offset for the SCC or SMC. The maximum number of ports is 4 SCCs and
100 * 2 SMCs. The "hub6" field is used to indicate the channel number, with
101 * a flag indicating SCC or SMC, and the number is used as an index into
102 * the CPM parameter area for this device.
103 * The "type" field is currently set to 0, for PORT_UNKNOWN. It is
104 * not currently used. I should probably use it to indicate the port
105 * type of SMC or SCC.
106 * The SMCs do not support any modem control signals.
107 */
108#define smc_scc_num hub6
109#define NUM_IS_SCC ((int)0x00010000)
110#define PORT_NUM(P) ((P) & 0x0000ffff)
111
112
113#if defined (CONFIG_UCQUICC)
114
115volatile extern void *_periph_base;
116/* sipex transceiver
117 * mode bits for are on pins
118 *
119 * SCC2 d16..19
120 * SCC3 d20..23
121 * SCC4 d24..27
122 */
123#define SIPEX_MODE(n,m) ((m & 0x0f)<<(16+4*(n-1)))
124
125static uint sipex_mode_bits = 0x00000000;
126
127#endif
128
129/* There is no `serial_state' defined back here in 2.0.
130 * Try to get by with serial_struct
131 */
132/* #define serial_state serial_struct */
133
134/* 2.4 -> 2.0 portability problem: async_icount in 2.4 has a few
135 * extras: */
136
137#if 0
138struct async_icount_24 {
139 __u32 cts, dsr, rng, dcd, tx, rx;
140 __u32 frame, parity, overrun, brk;
141 __u32 buf_overrun;
142} icount;
143#endif
144
145#if 0
146
147struct serial_state {
148 int magic;
149 int baud_base;
150 unsigned long port;
151 int irq;
152 int flags;
153 int hub6;
154 int type;
155 int line;
156 int revision; /* Chip revision (950) */
157 int xmit_fifo_size;
158 int custom_divisor;
159 int count;
160 u8 *iomem_base;
161 u16 iomem_reg_shift;
162 unsigned short close_delay;
163 unsigned short closing_wait; /* time to wait before closing */
164 struct async_icount_24 icount;
165 int io_type;
166 struct async_struct *info;
167};
168#endif
169
170#define SSTATE_MAGIC 0x5302
171
172
173
174/* SMC2 is sometimes used for low performance TDM interfaces. Define
175 * this as 1 if you want SMC2 as a serial port UART managed by this driver.
176 * Define this as 0 if you wish to use SMC2 for something else.
177 */
178#define USE_SMC2 1
179
180#if 0
181/* Define SCC to ttySx mapping. */
182#define SCC_NUM_BASE (USE_SMC2 + 1) /* SCC base tty "number" */
183
184/* Define which SCC is the first one to use for a serial port. These
185 * are 0-based numbers, i.e. this assumes the first SCC (SCC1) is used
186 * for Ethernet, and the first available SCC for serial UART is SCC2.
187 * NOTE: IF YOU CHANGE THIS, you have to change the PROFF_xxx and
188 * interrupt vectors in the table below to match.
189 */
190#define SCC_IDX_BASE 1 /* table index */
191#endif
192
193
194/* Processors other than the 860 only get SMCs configured by default.
195 * Either they don't have SCCs or they are allocated somewhere else.
196 * Of course, there are now 860s without some SCCs, so we will need to
197 * address that someday.
198 * The Embedded Planet Multimedia I/O cards use TDM interfaces to the
199 * stereo codec parts, and we use SMC2 to help support that.
200 */
201static struct serial_state rs_table[] = {
202/* type line PORT IRQ FLAGS smc_scc_num (F.K.A. hub6) */
203 { 0, 0, PRSLOT_SMC1, CPMVEC_SMC1, 0, 0 } /* SMC1 ttyS0 */
204#if USE_SMC2
205 ,{ 0, 0, PRSLOT_SMC2, CPMVEC_SMC2, 0, 1 } /* SMC2 ttyS1 */
206#endif
207
208#if defined(CONFIG_SERIAL_68360_SCC)
209 ,{ 0, 0, PRSLOT_SCC2, CPMVEC_SCC2, 0, (NUM_IS_SCC | 1) } /* SCC2 ttyS2 */
210 ,{ 0, 0, PRSLOT_SCC3, CPMVEC_SCC3, 0, (NUM_IS_SCC | 2) } /* SCC3 ttyS3 */
211 ,{ 0, 0, PRSLOT_SCC4, CPMVEC_SCC4, 0, (NUM_IS_SCC | 3) } /* SCC4 ttyS4 */
212#endif
213};
214
215#define NR_PORTS (sizeof(rs_table)/sizeof(struct serial_state))
216
217/* The number of buffer descriptors and their sizes.
218 */
219#define RX_NUM_FIFO 4
220#define RX_BUF_SIZE 32
221#define TX_NUM_FIFO 4
222#define TX_BUF_SIZE 32
223
224#define CONSOLE_NUM_FIFO 2
225#define CONSOLE_BUF_SIZE 4
226
227char *console_fifos[CONSOLE_NUM_FIFO * CONSOLE_BUF_SIZE];
228
229/* The async_struct in serial.h does not really give us what we
230 * need, so define our own here.
231 */
232typedef struct serial_info {
233 int magic;
234 int flags;
235
236 struct serial_state *state;
237 /* struct serial_struct *state; */
238 /* struct async_struct *state; */
239
240 struct tty_struct *tty;
241 int read_status_mask;
242 int ignore_status_mask;
243 int timeout;
244 int line;
245 int x_char; /* xon/xoff character */
246 int close_delay;
247 unsigned short closing_wait;
248 unsigned short closing_wait2;
249 unsigned long event;
250 unsigned long last_active;
251 int blocked_open; /* # of blocked opens */
252 struct work_struct tqueue;
253 struct work_struct tqueue_hangup;
254 wait_queue_head_t open_wait;
255 wait_queue_head_t close_wait;
256
257
258/* CPM Buffer Descriptor pointers.
259 */
260 QUICC_BD *rx_bd_base;
261 QUICC_BD *rx_cur;
262 QUICC_BD *tx_bd_base;
263 QUICC_BD *tx_cur;
264} ser_info_t;
265
266
267/* since kmalloc_init() does not get called until much after this initialization: */
268static ser_info_t quicc_ser_info[NR_PORTS];
269static char rx_buf_pool[NR_PORTS * RX_NUM_FIFO * RX_BUF_SIZE];
270static char tx_buf_pool[NR_PORTS * TX_NUM_FIFO * TX_BUF_SIZE];
271
272static void change_speed(ser_info_t *info);
273static void rs_360_wait_until_sent(struct tty_struct *tty, int timeout);
274
275static inline int serial_paranoia_check(ser_info_t *info,
276 char *name, const char *routine)
277{
278#ifdef SERIAL_PARANOIA_CHECK
279 static const char *badmagic =
280 "Warning: bad magic number for serial struct (%s) in %s\n";
281 static const char *badinfo =
282 "Warning: null async_struct for (%s) in %s\n";
283
284 if (!info) {
285 printk(badinfo, name, routine);
286 return 1;
287 }
288 if (info->magic != SERIAL_MAGIC) {
289 printk(badmagic, name, routine);
290 return 1;
291 }
292#endif
293 return 0;
294}
295
296/*
297 * This is used to figure out the divisor speeds and the timeouts,
298 * indexed by the termio value. The generic CPM functions are responsible
299 * for setting and assigning baud rate generators for us.
300 */
301static int baud_table[] = {
302 0, 50, 75, 110, 134, 150, 200, 300, 600, 1200, 1800, 2400, 4800,
303 9600, 19200, 38400, 57600, 115200, 230400, 460800, 0 };
304
305/* This sucks. There is a better way: */
306#if defined(CONFIG_CONSOLE_9600)
307 #define CONSOLE_BAUDRATE 9600
308#elif defined(CONFIG_CONSOLE_19200)
309 #define CONSOLE_BAUDRATE 19200
310#elif defined(CONFIG_CONSOLE_115200)
311 #define CONSOLE_BAUDRATE 115200
312#else
313 #warning "console baud rate undefined"
314 #define CONSOLE_BAUDRATE 9600
315#endif
316
317/*
318 * ------------------------------------------------------------
319 * rs_stop() and rs_start()
320 *
321 * This routines are called before setting or resetting tty->stopped.
322 * They enable or disable transmitter interrupts, as necessary.
323 * ------------------------------------------------------------
324 */
325static void rs_360_stop(struct tty_struct *tty)
326{
327 ser_info_t *info = (ser_info_t *)tty->driver_data;
328 int idx;
329 unsigned long flags;
330 volatile struct scc_regs *sccp;
331 volatile struct smc_regs *smcp;
332
333 if (serial_paranoia_check(info, tty->name, "rs_stop"))
334 return;
335
336 local_irq_save(flags);
337 idx = PORT_NUM(info->state->smc_scc_num);
338 if (info->state->smc_scc_num & NUM_IS_SCC) {
339 sccp = &pquicc->scc_regs[idx];
340 sccp->scc_sccm &= ~UART_SCCM_TX;
341 } else {
342 /* smcp = &cpmp->cp_smc[idx]; */
343 smcp = &pquicc->smc_regs[idx];
344 smcp->smc_smcm &= ~SMCM_TX;
345 }
346 local_irq_restore(flags);
347}
348
349
350static void rs_360_start(struct tty_struct *tty)
351{
352 ser_info_t *info = (ser_info_t *)tty->driver_data;
353 int idx;
354 unsigned long flags;
355 volatile struct scc_regs *sccp;
356 volatile struct smc_regs *smcp;
357
358 if (serial_paranoia_check(info, tty->name, "rs_stop"))
359 return;
360
361 local_irq_save(flags);
362 idx = PORT_NUM(info->state->smc_scc_num);
363 if (info->state->smc_scc_num & NUM_IS_SCC) {
364 sccp = &pquicc->scc_regs[idx];
365 sccp->scc_sccm |= UART_SCCM_TX;
366 } else {
367 smcp = &pquicc->smc_regs[idx];
368 smcp->smc_smcm |= SMCM_TX;
369 }
370 local_irq_restore(flags);
371}
372
373/*
374 * ----------------------------------------------------------------------
375 *
376 * Here starts the interrupt handling routines. All of the following
377 * subroutines are declared as inline and are folded into
378 * rs_interrupt(). They were separated out for readability's sake.
379 *
380 * Note: rs_interrupt() is a "fast" interrupt, which means that it
381 * runs with interrupts turned off. People who may want to modify
382 * rs_interrupt() should try to keep the interrupt handler as fast as
383 * possible. After you are done making modifications, it is not a bad
384 * idea to do:
385 *
386 * gcc -S -DKERNEL -Wall -Wstrict-prototypes -O6 -fomit-frame-pointer serial.c
387 *
388 * and look at the resulting assemble code in serial.s.
389 *
390 * - Ted Ts'o (tytso@mit.edu), 7-Mar-93
391 * -----------------------------------------------------------------------
392 */
393
394static _INLINE_ void receive_chars(ser_info_t *info)
395{
396 struct tty_struct *tty = info->port.tty;
397 unsigned char ch, flag, *cp;
398 /*int ignored = 0;*/
399 int i;
400 ushort status;
401 struct async_icount *icount;
402 /* struct async_icount_24 *icount; */
403 volatile QUICC_BD *bdp;
404
405 icount = &info->state->icount;
406
407 /* Just loop through the closed BDs and copy the characters into
408 * the buffer.
409 */
410 bdp = info->rx_cur;
411 for (;;) {
412 if (bdp->status & BD_SC_EMPTY) /* If this one is empty */
413 break; /* we are all done */
414
415 /* The read status mask tell us what we should do with
416 * incoming characters, especially if errors occur.
417 * One special case is the use of BD_SC_EMPTY. If
418 * this is not set, we are supposed to be ignoring
419 * inputs. In this case, just mark the buffer empty and
420 * continue.
421 */
422 if (!(info->read_status_mask & BD_SC_EMPTY)) {
423 bdp->status |= BD_SC_EMPTY;
424 bdp->status &=
425 ~(BD_SC_BR | BD_SC_FR | BD_SC_PR | BD_SC_OV);
426
427 if (bdp->status & BD_SC_WRAP)
428 bdp = info->rx_bd_base;
429 else
430 bdp++;
431 continue;
432 }
433
434 /* Get the number of characters and the buffer pointer.
435 */
436 i = bdp->length;
437 /* cp = (unsigned char *)__va(bdp->buf); */
438 cp = (char *)bdp->buf;
439 status = bdp->status;
440
441 while (i-- > 0) {
442 ch = *cp++;
443 icount->rx++;
444
445#ifdef SERIAL_DEBUG_INTR
446 printk("DR%02x:%02x...", ch, status);
447#endif
448 flag = TTY_NORMAL;
449
450 if (status & (BD_SC_BR | BD_SC_FR |
451 BD_SC_PR | BD_SC_OV)) {
452 /*
453 * For statistics only
454 */
455 if (status & BD_SC_BR)
456 icount->brk++;
457 else if (status & BD_SC_PR)
458 icount->parity++;
459 else if (status & BD_SC_FR)
460 icount->frame++;
461 if (status & BD_SC_OV)
462 icount->overrun++;
463
464 /*
465 * Now check to see if character should be
466 * ignored, and mask off conditions which
467 * should be ignored.
468 if (status & info->ignore_status_mask) {
469 if (++ignored > 100)
470 break;
471 continue;
472 }
473 */
474 status &= info->read_status_mask;
475
476 if (status & (BD_SC_BR)) {
477#ifdef SERIAL_DEBUG_INTR
478 printk("handling break....");
479#endif
480 *tty->flip.flag_buf_ptr = TTY_BREAK;
481 if (info->flags & ASYNC_SAK)
482 do_SAK(tty);
483 } else if (status & BD_SC_PR)
484 flag = TTY_PARITY;
485 else if (status & BD_SC_FR)
486 flag = TTY_FRAME;
487 }
488 tty_insert_flip_char(tty, ch, flag);
489 if (status & BD_SC_OV)
490 /*
491 * Overrun is special, since it's
492 * reported immediately, and doesn't
493 * affect the current character
494 */
495 tty_insert_flip_char(tty, 0, TTY_OVERRUN);
496 }
497
498 /* This BD is ready to be used again. Clear status.
499 * Get next BD.
500 */
501 bdp->status |= BD_SC_EMPTY;
502 bdp->status &= ~(BD_SC_BR | BD_SC_FR | BD_SC_PR | BD_SC_OV);
503
504 if (bdp->status & BD_SC_WRAP)
505 bdp = info->rx_bd_base;
506 else
507 bdp++;
508 }
509
510 info->rx_cur = (QUICC_BD *)bdp;
511
512 tty_schedule_flip(tty);
513}
514
515static _INLINE_ void receive_break(ser_info_t *info)
516{
517 struct tty_struct *tty = info->port.tty;
518
519 info->state->icount.brk++;
520 /* Check to see if there is room in the tty buffer for
521 * the break. If not, we exit now, losing the break. FIXME
522 */
523 tty_insert_flip_char(tty, 0, TTY_BREAK);
524 tty_schedule_flip(tty);
525}
526
527static _INLINE_ void transmit_chars(ser_info_t *info)
528{
529
530 if ((info->flags & TX_WAKEUP) ||
531 (info->port.tty->flags & (1 << TTY_DO_WRITE_WAKEUP))) {
532 schedule_work(&info->tqueue);
533 }
534
535#ifdef SERIAL_DEBUG_INTR
536 printk("THRE...");
537#endif
538}
539
540#ifdef notdef
541 /* I need to do this for the SCCs, so it is left as a reminder.
542 */
543static _INLINE_ void check_modem_status(struct async_struct *info)
544{
545 int status;
546 /* struct async_icount *icount; */
547 struct async_icount_24 *icount;
548
549 status = serial_in(info, UART_MSR);
550
551 if (status & UART_MSR_ANY_DELTA) {
552 icount = &info->state->icount;
553 /* update input line counters */
554 if (status & UART_MSR_TERI)
555 icount->rng++;
556 if (status & UART_MSR_DDSR)
557 icount->dsr++;
558 if (status & UART_MSR_DDCD) {
559 icount->dcd++;
560#ifdef CONFIG_HARD_PPS
561 if ((info->flags & ASYNC_HARDPPS_CD) &&
562 (status & UART_MSR_DCD))
563 hardpps();
564#endif
565 }
566 if (status & UART_MSR_DCTS)
567 icount->cts++;
568 wake_up_interruptible(&info->delta_msr_wait);
569 }
570
571 if ((info->flags & ASYNC_CHECK_CD) && (status & UART_MSR_DDCD)) {
572#if (defined(SERIAL_DEBUG_OPEN) || defined(SERIAL_DEBUG_INTR))
573 printk("ttys%d CD now %s...", info->line,
574 (status & UART_MSR_DCD) ? "on" : "off");
575#endif
576 if (status & UART_MSR_DCD)
577 wake_up_interruptible(&info->open_wait);
578 else {
579#ifdef SERIAL_DEBUG_OPEN
580 printk("scheduling hangup...");
581#endif
582 queue_task(&info->tqueue_hangup,
583 &tq_scheduler);
584 }
585 }
586 if (info->flags & ASYNC_CTS_FLOW) {
587 if (info->port.tty->hw_stopped) {
588 if (status & UART_MSR_CTS) {
589#if (defined(SERIAL_DEBUG_INTR) || defined(SERIAL_DEBUG_FLOW))
590 printk("CTS tx start...");
591#endif
592 info->port.tty->hw_stopped = 0;
593 info->IER |= UART_IER_THRI;
594 serial_out(info, UART_IER, info->IER);
595 rs_sched_event(info, RS_EVENT_WRITE_WAKEUP);
596 return;
597 }
598 } else {
599 if (!(status & UART_MSR_CTS)) {
600#if (defined(SERIAL_DEBUG_INTR) || defined(SERIAL_DEBUG_FLOW))
601 printk("CTS tx stop...");
602#endif
603 info->port.tty->hw_stopped = 1;
604 info->IER &= ~UART_IER_THRI;
605 serial_out(info, UART_IER, info->IER);
606 }
607 }
608 }
609}
610#endif
611
612/*
613 * This is the serial driver's interrupt routine for a single port
614 */
615/* static void rs_360_interrupt(void *dev_id) */ /* until and if we start servicing irqs here */
616static void rs_360_interrupt(int vec, void *dev_id)
617{
618 u_char events;
619 int idx;
620 ser_info_t *info;
621 volatile struct smc_regs *smcp;
622 volatile struct scc_regs *sccp;
623
624 info = dev_id;
625
626 idx = PORT_NUM(info->state->smc_scc_num);
627 if (info->state->smc_scc_num & NUM_IS_SCC) {
628 sccp = &pquicc->scc_regs[idx];
629 events = sccp->scc_scce;
630 if (events & SCCM_RX)
631 receive_chars(info);
632 if (events & SCCM_TX)
633 transmit_chars(info);
634 sccp->scc_scce = events;
635 } else {
636 smcp = &pquicc->smc_regs[idx];
637 events = smcp->smc_smce;
638 if (events & SMCM_BRKE)
639 receive_break(info);
640 if (events & SMCM_RX)
641 receive_chars(info);
642 if (events & SMCM_TX)
643 transmit_chars(info);
644 smcp->smc_smce = events;
645 }
646
647#ifdef SERIAL_DEBUG_INTR
648 printk("rs_interrupt_single(%d, %x)...",
649 info->state->smc_scc_num, events);
650#endif
651#ifdef modem_control
652 check_modem_status(info);
653#endif
654 info->last_active = jiffies;
655#ifdef SERIAL_DEBUG_INTR
656 printk("end.\n");
657#endif
658}
659
660
661/*
662 * -------------------------------------------------------------------
663 * Here ends the serial interrupt routines.
664 * -------------------------------------------------------------------
665 */
666
667
668static void do_softint(void *private_)
669{
670 ser_info_t *info = (ser_info_t *) private_;
671 struct tty_struct *tty;
672
673 tty = info->port.tty;
674 if (!tty)
675 return;
676
677 if (test_and_clear_bit(RS_EVENT_WRITE_WAKEUP, &info->event))
678 tty_wakeup(tty);
679}
680
681
682/*
683 * This routine is called from the scheduler tqueue when the interrupt
684 * routine has signalled that a hangup has occurred. The path of
685 * hangup processing is:
686 *
687 * serial interrupt routine -> (scheduler tqueue) ->
688 * do_serial_hangup() -> tty->hangup() -> rs_hangup()
689 *
690 */
691static void do_serial_hangup(void *private_)
692{
693 struct async_struct *info = (struct async_struct *) private_;
694 struct tty_struct *tty;
695
696 tty = info->port.tty;
697 if (!tty)
698 return;
699
700 tty_hangup(tty);
701}
702
703
704static int startup(ser_info_t *info)
705{
706 unsigned long flags;
707 int retval=0;
708 int idx;
709 /*struct serial_state *state = info->state;*/
710 volatile struct smc_regs *smcp;
711 volatile struct scc_regs *sccp;
712 volatile struct smc_uart_pram *up;
713 volatile struct uart_pram *scup;
714
715
716 local_irq_save(flags);
717
718 if (info->flags & ASYNC_INITIALIZED) {
719 goto errout;
720 }
721
722#ifdef maybe
723 if (!state->port || !state->type) {
724 if (info->port.tty)
725 set_bit(TTY_IO_ERROR, &info->port.tty->flags);
726 goto errout;
727 }
728#endif
729
730#ifdef SERIAL_DEBUG_OPEN
731 printk("starting up ttys%d (irq %d)...", info->line, state->irq);
732#endif
733
734
735#ifdef modem_control
736 info->MCR = 0;
737 if (info->port.tty->termios->c_cflag & CBAUD)
738 info->MCR = UART_MCR_DTR | UART_MCR_RTS;
739#endif
740
741 if (info->port.tty)
742 clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
743
744 /*
745 * and set the speed of the serial port
746 */
747 change_speed(info);
748
749 idx = PORT_NUM(info->state->smc_scc_num);
750 if (info->state->smc_scc_num & NUM_IS_SCC) {
751 sccp = &pquicc->scc_regs[idx];
752 scup = &pquicc->pram[info->state->port].scc.pscc.u;
753
754 scup->mrblr = RX_BUF_SIZE;
755 scup->max_idl = RX_BUF_SIZE;
756
757 sccp->scc_sccm |= (UART_SCCM_TX | UART_SCCM_RX);
758 sccp->scc_gsmr.w.low |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT);
759
760 } else {
761 smcp = &pquicc->smc_regs[idx];
762
763 /* Enable interrupts and I/O.
764 */
765 smcp->smc_smcm |= (SMCM_RX | SMCM_TX);
766 smcp->smc_smcmr |= (SMCMR_REN | SMCMR_TEN);
767
768 /* We can tune the buffer length and idle characters
769 * to take advantage of the entire incoming buffer size.
770 * If mrblr is something other than 1, maxidl has to be
771 * non-zero or we never get an interrupt. The maxidl
772 * is the number of character times we wait after reception
773 * of the last character before we decide no more characters
774 * are coming.
775 */
776 /* up = (smc_uart_t *)&pquicc->cp_dparam[state->port]; */
777 /* holy unionized structures, Batman: */
778 up = &pquicc->pram[info->state->port].scc.pothers.idma_smc.psmc.u;
779
780 up->mrblr = RX_BUF_SIZE;
781 up->max_idl = RX_BUF_SIZE;
782
783 up->brkcr = 1; /* number of break chars */
784 }
785
786 info->flags |= ASYNC_INITIALIZED;
787 local_irq_restore(flags);
788 return 0;
789
790errout:
791 local_irq_restore(flags);
792 return retval;
793}
794
795/*
796 * This routine will shutdown a serial port; interrupts are disabled, and
797 * DTR is dropped if the hangup on close termio flag is on.
798 */
799static void shutdown(ser_info_t *info)
800{
801 unsigned long flags;
802 struct serial_state *state;
803 int idx;
804 volatile struct smc_regs *smcp;
805 volatile struct scc_regs *sccp;
806
807 if (!(info->flags & ASYNC_INITIALIZED))
808 return;
809
810 state = info->state;
811
812#ifdef SERIAL_DEBUG_OPEN
813 printk("Shutting down serial port %d (irq %d)....", info->line,
814 state->irq);
815#endif
816
817 local_irq_save(flags);
818
819 idx = PORT_NUM(state->smc_scc_num);
820 if (state->smc_scc_num & NUM_IS_SCC) {
821 sccp = &pquicc->scc_regs[idx];
822 sccp->scc_gsmr.w.low &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
823#ifdef CONFIG_SERIAL_CONSOLE
824 /* We can't disable the transmitter if this is the
825 * system console.
826 */
827 if ((state - rs_table) != CONFIG_SERIAL_CONSOLE_PORT)
828#endif
829 sccp->scc_sccm &= ~(UART_SCCM_TX | UART_SCCM_RX);
830 } else {
831 smcp = &pquicc->smc_regs[idx];
832
833 /* Disable interrupts and I/O.
834 */
835 smcp->smc_smcm &= ~(SMCM_RX | SMCM_TX);
836#ifdef CONFIG_SERIAL_CONSOLE
837 /* We can't disable the transmitter if this is the
838 * system console.
839 */
840 if ((state - rs_table) != CONFIG_SERIAL_CONSOLE_PORT)
841#endif
842 smcp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
843 }
844
845 if (info->port.tty)
846 set_bit(TTY_IO_ERROR, &info->port.tty->flags);
847
848 info->flags &= ~ASYNC_INITIALIZED;
849 local_irq_restore(flags);
850}
851
852/*
853 * This routine is called to set the UART divisor registers to match
854 * the specified baud rate for a serial port.
855 */
856static void change_speed(ser_info_t *info)
857{
858 int baud_rate;
859 unsigned cflag, cval, scval, prev_mode;
860 int i, bits, sbits, idx;
861 unsigned long flags;
862 struct serial_state *state;
863 volatile struct smc_regs *smcp;
864 volatile struct scc_regs *sccp;
865
866 if (!info->port.tty || !info->port.tty->termios)
867 return;
868 cflag = info->port.tty->termios->c_cflag;
869
870 state = info->state;
871
872 /* Character length programmed into the mode register is the
873 * sum of: 1 start bit, number of data bits, 0 or 1 parity bit,
874 * 1 or 2 stop bits, minus 1.
875 * The value 'bits' counts this for us.
876 */
877 cval = 0;
878 scval = 0;
879
880 /* byte size and parity */
881 switch (cflag & CSIZE) {
882 case CS5: bits = 5; break;
883 case CS6: bits = 6; break;
884 case CS7: bits = 7; break;
885 case CS8: bits = 8; break;
886 /* Never happens, but GCC is too dumb to figure it out */
887 default: bits = 8; break;
888 }
889 sbits = bits - 5;
890
891 if (cflag & CSTOPB) {
892 cval |= SMCMR_SL; /* Two stops */
893 scval |= SCU_PMSR_SL;
894 bits++;
895 }
896 if (cflag & PARENB) {
897 cval |= SMCMR_PEN;
898 scval |= SCU_PMSR_PEN;
899 bits++;
900 }
901 if (!(cflag & PARODD)) {
902 cval |= SMCMR_PM_EVEN;
903 scval |= (SCU_PMSR_REVP | SCU_PMSR_TEVP);
904 }
905
906 /* Determine divisor based on baud rate */
907 i = cflag & CBAUD;
908 if (i >= (sizeof(baud_table)/sizeof(int)))
909 baud_rate = 9600;
910 else
911 baud_rate = baud_table[i];
912
913 info->timeout = (TX_BUF_SIZE*HZ*bits);
914 info->timeout += HZ/50; /* Add .02 seconds of slop */
915
916#ifdef modem_control
917 /* CTS flow control flag and modem status interrupts */
918 info->IER &= ~UART_IER_MSI;
919 if (info->flags & ASYNC_HARDPPS_CD)
920 info->IER |= UART_IER_MSI;
921 if (cflag & CRTSCTS) {
922 info->flags |= ASYNC_CTS_FLOW;
923 info->IER |= UART_IER_MSI;
924 } else
925 info->flags &= ~ASYNC_CTS_FLOW;
926 if (cflag & CLOCAL)
927 info->flags &= ~ASYNC_CHECK_CD;
928 else {
929 info->flags |= ASYNC_CHECK_CD;
930 info->IER |= UART_IER_MSI;
931 }
932 serial_out(info, UART_IER, info->IER);
933#endif
934
935 /*
936 * Set up parity check flag
937 */
938 info->read_status_mask = (BD_SC_EMPTY | BD_SC_OV);
939 if (I_INPCK(info->port.tty))
940 info->read_status_mask |= BD_SC_FR | BD_SC_PR;
941 if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty))
942 info->read_status_mask |= BD_SC_BR;
943
944 /*
945 * Characters to ignore
946 */
947 info->ignore_status_mask = 0;
948 if (I_IGNPAR(info->port.tty))
949 info->ignore_status_mask |= BD_SC_PR | BD_SC_FR;
950 if (I_IGNBRK(info->port.tty)) {
951 info->ignore_status_mask |= BD_SC_BR;
952 /*
953 * If we're ignore parity and break indicators, ignore
954 * overruns too. (For real raw support).
955 */
956 if (I_IGNPAR(info->port.tty))
957 info->ignore_status_mask |= BD_SC_OV;
958 }
959 /*
960 * !!! ignore all characters if CREAD is not set
961 */
962 if ((cflag & CREAD) == 0)
963 info->read_status_mask &= ~BD_SC_EMPTY;
964 local_irq_save(flags);
965
966 /* Start bit has not been added (so don't, because we would just
967 * subtract it later), and we need to add one for the number of
968 * stops bits (there is always at least one).
969 */
970 bits++;
971 idx = PORT_NUM(state->smc_scc_num);
972 if (state->smc_scc_num & NUM_IS_SCC) {
973 sccp = &pquicc->scc_regs[idx];
974 sccp->scc_psmr = (sbits << 12) | scval;
975 } else {
976 smcp = &pquicc->smc_regs[idx];
977
978 /* Set the mode register. We want to keep a copy of the
979 * enables, because we want to put them back if they were
980 * present.
981 */
982 prev_mode = smcp->smc_smcmr;
983 smcp->smc_smcmr = smcr_mk_clen(bits) | cval | SMCMR_SM_UART;
984 smcp->smc_smcmr |= (prev_mode & (SMCMR_REN | SMCMR_TEN));
985 }
986
987 m360_cpm_setbrg((state - rs_table), baud_rate);
988
989 local_irq_restore(flags);
990}
991
992static void rs_360_put_char(struct tty_struct *tty, unsigned char ch)
993{
994 ser_info_t *info = (ser_info_t *)tty->driver_data;
995 volatile QUICC_BD *bdp;
996
997 if (serial_paranoia_check(info, tty->name, "rs_put_char"))
998 return 0;
999
1000 if (!tty)
1001 return 0;
1002
1003 bdp = info->tx_cur;
1004 while (bdp->status & BD_SC_READY);
1005
1006 /* *((char *)__va(bdp->buf)) = ch; */
1007 *((char *)bdp->buf) = ch;
1008 bdp->length = 1;
1009 bdp->status |= BD_SC_READY;
1010
1011 /* Get next BD.
1012 */
1013 if (bdp->status & BD_SC_WRAP)
1014 bdp = info->tx_bd_base;
1015 else
1016 bdp++;
1017
1018 info->tx_cur = (QUICC_BD *)bdp;
1019 return 1;
1020
1021}
1022
1023static int rs_360_write(struct tty_struct * tty,
1024 const unsigned char *buf, int count)
1025{
1026 int c, ret = 0;
1027 ser_info_t *info = (ser_info_t *)tty->driver_data;
1028 volatile QUICC_BD *bdp;
1029
1030#ifdef CONFIG_KGDB
1031 /* Try to let stub handle output. Returns true if it did. */
1032 if (kgdb_output_string(buf, count))
1033 return ret;
1034#endif
1035
1036 if (serial_paranoia_check(info, tty->name, "rs_write"))
1037 return 0;
1038
1039 if (!tty)
1040 return 0;
1041
1042 bdp = info->tx_cur;
1043
1044 while (1) {
1045 c = min(count, TX_BUF_SIZE);
1046
1047 if (c <= 0)
1048 break;
1049
1050 if (bdp->status & BD_SC_READY) {
1051 info->flags |= TX_WAKEUP;
1052 break;
1053 }
1054
1055 /* memcpy(__va(bdp->buf), buf, c); */
1056 memcpy((void *)bdp->buf, buf, c);
1057
1058 bdp->length = c;
1059 bdp->status |= BD_SC_READY;
1060
1061 buf += c;
1062 count -= c;
1063 ret += c;
1064
1065 /* Get next BD.
1066 */
1067 if (bdp->status & BD_SC_WRAP)
1068 bdp = info->tx_bd_base;
1069 else
1070 bdp++;
1071 info->tx_cur = (QUICC_BD *)bdp;
1072 }
1073 return ret;
1074}
1075
1076static int rs_360_write_room(struct tty_struct *tty)
1077{
1078 ser_info_t *info = (ser_info_t *)tty->driver_data;
1079 int ret;
1080
1081 if (serial_paranoia_check(info, tty->name, "rs_write_room"))
1082 return 0;
1083
1084 if ((info->tx_cur->status & BD_SC_READY) == 0) {
1085 info->flags &= ~TX_WAKEUP;
1086 ret = TX_BUF_SIZE;
1087 }
1088 else {
1089 info->flags |= TX_WAKEUP;
1090 ret = 0;
1091 }
1092 return ret;
1093}
1094
1095/* I could track this with transmit counters....maybe later.
1096*/
1097static int rs_360_chars_in_buffer(struct tty_struct *tty)
1098{
1099 ser_info_t *info = (ser_info_t *)tty->driver_data;
1100
1101 if (serial_paranoia_check(info, tty->name, "rs_chars_in_buffer"))
1102 return 0;
1103 return 0;
1104}
1105
1106static void rs_360_flush_buffer(struct tty_struct *tty)
1107{
1108 ser_info_t *info = (ser_info_t *)tty->driver_data;
1109
1110 if (serial_paranoia_check(info, tty->name, "rs_flush_buffer"))
1111 return;
1112
1113 /* There is nothing to "flush", whatever we gave the CPM
1114 * is on its way out.
1115 */
1116 tty_wakeup(tty);
1117 info->flags &= ~TX_WAKEUP;
1118}
1119
1120/*
1121 * This function is used to send a high-priority XON/XOFF character to
1122 * the device
1123 */
1124static void rs_360_send_xchar(struct tty_struct *tty, char ch)
1125{
1126 volatile QUICC_BD *bdp;
1127
1128 ser_info_t *info = (ser_info_t *)tty->driver_data;
1129
1130 if (serial_paranoia_check(info, tty->name, "rs_send_char"))
1131 return;
1132
1133 bdp = info->tx_cur;
1134 while (bdp->status & BD_SC_READY);
1135
1136 /* *((char *)__va(bdp->buf)) = ch; */
1137 *((char *)bdp->buf) = ch;
1138 bdp->length = 1;
1139 bdp->status |= BD_SC_READY;
1140
1141 /* Get next BD.
1142 */
1143 if (bdp->status & BD_SC_WRAP)
1144 bdp = info->tx_bd_base;
1145 else
1146 bdp++;
1147
1148 info->tx_cur = (QUICC_BD *)bdp;
1149}
1150
1151/*
1152 * ------------------------------------------------------------
1153 * rs_throttle()
1154 *
1155 * This routine is called by the upper-layer tty layer to signal that
1156 * incoming characters should be throttled.
1157 * ------------------------------------------------------------
1158 */
1159static void rs_360_throttle(struct tty_struct * tty)
1160{
1161 ser_info_t *info = (ser_info_t *)tty->driver_data;
1162#ifdef SERIAL_DEBUG_THROTTLE
1163 char buf[64];
1164
1165 printk("throttle %s: %d....\n", _tty_name(tty, buf),
1166 tty->ldisc.chars_in_buffer(tty));
1167#endif
1168
1169 if (serial_paranoia_check(info, tty->name, "rs_throttle"))
1170 return;
1171
1172 if (I_IXOFF(tty))
1173 rs_360_send_xchar(tty, STOP_CHAR(tty));
1174
1175#ifdef modem_control
1176 if (tty->termios->c_cflag & CRTSCTS)
1177 info->MCR &= ~UART_MCR_RTS;
1178
1179 local_irq_disable();
1180 serial_out(info, UART_MCR, info->MCR);
1181 local_irq_enable();
1182#endif
1183}
1184
1185static void rs_360_unthrottle(struct tty_struct * tty)
1186{
1187 ser_info_t *info = (ser_info_t *)tty->driver_data;
1188#ifdef SERIAL_DEBUG_THROTTLE
1189 char buf[64];
1190
1191 printk("unthrottle %s: %d....\n", _tty_name(tty, buf),
1192 tty->ldisc.chars_in_buffer(tty));
1193#endif
1194
1195 if (serial_paranoia_check(info, tty->name, "rs_unthrottle"))
1196 return;
1197
1198 if (I_IXOFF(tty)) {
1199 if (info->x_char)
1200 info->x_char = 0;
1201 else
1202 rs_360_send_xchar(tty, START_CHAR(tty));
1203 }
1204#ifdef modem_control
1205 if (tty->termios->c_cflag & CRTSCTS)
1206 info->MCR |= UART_MCR_RTS;
1207 local_irq_disable();
1208 serial_out(info, UART_MCR, info->MCR);
1209 local_irq_enable();
1210#endif
1211}
1212
1213/*
1214 * ------------------------------------------------------------
1215 * rs_ioctl() and friends
1216 * ------------------------------------------------------------
1217 */
1218
1219#ifdef maybe
1220/*
1221 * get_lsr_info - get line status register info
1222 *
1223 * Purpose: Let user call ioctl() to get info when the UART physically
1224 * is emptied. On bus types like RS485, the transmitter must
1225 * release the bus after transmitting. This must be done when
1226 * the transmit shift register is empty, not be done when the
1227 * transmit holding register is empty. This functionality
1228 * allows an RS485 driver to be written in user space.
1229 */
1230static int get_lsr_info(struct async_struct * info, unsigned int *value)
1231{
1232 unsigned char status;
1233 unsigned int result;
1234
1235 local_irq_disable();
1236 status = serial_in(info, UART_LSR);
1237 local_irq_enable();
1238 result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0);
1239 return put_user(result,value);
1240}
1241#endif
1242
1243static int rs_360_tiocmget(struct tty_struct *tty, struct file *file)
1244{
1245 ser_info_t *info = (ser_info_t *)tty->driver_data;
1246 unsigned int result = 0;
1247#ifdef modem_control
1248 unsigned char control, status;
1249
1250 if (serial_paranoia_check(info, tty->name, __func__))
1251 return -ENODEV;
1252
1253 if (tty->flags & (1 << TTY_IO_ERROR))
1254 return -EIO;
1255
1256 control = info->MCR;
1257 local_irq_disable();
1258 status = serial_in(info, UART_MSR);
1259 local_irq_enable();
1260 result = ((control & UART_MCR_RTS) ? TIOCM_RTS : 0)
1261 | ((control & UART_MCR_DTR) ? TIOCM_DTR : 0)
1262#ifdef TIOCM_OUT1
1263 | ((control & UART_MCR_OUT1) ? TIOCM_OUT1 : 0)
1264 | ((control & UART_MCR_OUT2) ? TIOCM_OUT2 : 0)
1265#endif
1266 | ((status & UART_MSR_DCD) ? TIOCM_CAR : 0)
1267 | ((status & UART_MSR_RI) ? TIOCM_RNG : 0)
1268 | ((status & UART_MSR_DSR) ? TIOCM_DSR : 0)
1269 | ((status & UART_MSR_CTS) ? TIOCM_CTS : 0);
1270#endif
1271 return result;
1272}
1273
1274static int rs_360_tiocmset(struct tty_struct *tty, struct file *file,
1275 unsigned int set, unsigned int clear)
1276{
1277#ifdef modem_control
1278 ser_info_t *info = (ser_info_t *)tty->driver_data;
1279 unsigned int arg;
1280
1281 if (serial_paranoia_check(info, tty->name, __func__))
1282 return -ENODEV;
1283
1284 if (tty->flags & (1 << TTY_IO_ERROR))
1285 return -EIO;
1286 /* FIXME: locking on info->mcr */
1287 if (set & TIOCM_RTS)
1288 info->mcr |= UART_MCR_RTS;
1289 if (set & TIOCM_DTR)
1290 info->mcr |= UART_MCR_DTR;
1291 if (clear & TIOCM_RTS)
1292 info->MCR &= ~UART_MCR_RTS;
1293 if (clear & TIOCM_DTR)
1294 info->MCR &= ~UART_MCR_DTR;
1295
1296#ifdef TIOCM_OUT1
1297 if (set & TIOCM_OUT1)
1298 info->MCR |= UART_MCR_OUT1;
1299 if (set & TIOCM_OUT2)
1300 info->MCR |= UART_MCR_OUT2;
1301 if (clear & TIOCM_OUT1)
1302 info->MCR &= ~UART_MCR_OUT1;
1303 if (clear & TIOCM_OUT2)
1304 info->MCR &= ~UART_MCR_OUT2;
1305#endif
1306
1307 local_irq_disable();
1308 serial_out(info, UART_MCR, info->MCR);
1309 local_irq_enable();
1310#endif
1311 return 0;
1312}
1313
1314/* Sending a break is a two step process on the SMC/SCC. It is accomplished
1315 * by sending a STOP TRANSMIT command followed by a RESTART TRANSMIT
1316 * command. We take advantage of the begin/end functions to make this
1317 * happen.
1318 */
1319static ushort smc_chan_map[] = {
1320 CPM_CR_CH_SMC1,
1321 CPM_CR_CH_SMC2
1322};
1323
1324static ushort scc_chan_map[] = {
1325 CPM_CR_CH_SCC1,
1326 CPM_CR_CH_SCC2,
1327 CPM_CR_CH_SCC3,
1328 CPM_CR_CH_SCC4
1329};
1330
1331static void begin_break(ser_info_t *info)
1332{
1333 volatile QUICC *cp;
1334 ushort chan;
1335 int idx;
1336
1337 cp = pquicc;
1338
1339 idx = PORT_NUM(info->state->smc_scc_num);
1340 if (info->state->smc_scc_num & NUM_IS_SCC)
1341 chan = scc_chan_map[idx];
1342 else
1343 chan = smc_chan_map[idx];
1344
1345 cp->cp_cr = mk_cr_cmd(chan, CPM_CR_STOP_TX) | CPM_CR_FLG;
1346 while (cp->cp_cr & CPM_CR_FLG);
1347}
1348
1349static void end_break(ser_info_t *info)
1350{
1351 volatile QUICC *cp;
1352 ushort chan;
1353 int idx;
1354
1355 cp = pquicc;
1356
1357 idx = PORT_NUM(info->state->smc_scc_num);
1358 if (info->state->smc_scc_num & NUM_IS_SCC)
1359 chan = scc_chan_map[idx];
1360 else
1361 chan = smc_chan_map[idx];
1362
1363 cp->cp_cr = mk_cr_cmd(chan, CPM_CR_RESTART_TX) | CPM_CR_FLG;
1364 while (cp->cp_cr & CPM_CR_FLG);
1365}
1366
1367/*
1368 * This routine sends a break character out the serial port.
1369 */
1370static void send_break(ser_info_t *info, unsigned int duration)
1371{
1372#ifdef SERIAL_DEBUG_SEND_BREAK
1373 printk("rs_send_break(%d) jiff=%lu...", duration, jiffies);
1374#endif
1375 begin_break(info);
1376 msleep_interruptible(duration);
1377 end_break(info);
1378#ifdef SERIAL_DEBUG_SEND_BREAK
1379 printk("done jiffies=%lu\n", jiffies);
1380#endif
1381}
1382
1383
1384/*
1385 * Get counter of input serial line interrupts (DCD,RI,DSR,CTS)
1386 * Return: write counters to the user passed counter struct
1387 * NB: both 1->0 and 0->1 transitions are counted except for
1388 * RI where only 0->1 is counted.
1389 */
1390static int rs_360_get_icount(struct tty_struct *tty,
1391 struct serial_icounter_struct *icount)
1392{
1393 ser_info_t *info = (ser_info_t *)tty->driver_data;
1394 struct async_icount cnow;
1395
1396 local_irq_disable();
1397 cnow = info->state->icount;
1398 local_irq_enable();
1399
1400 icount->cts = cnow.cts;
1401 icount->dsr = cnow.dsr;
1402 icount->rng = cnow.rng;
1403 icount->dcd = cnow.dcd;
1404
1405 return 0;
1406}
1407
1408static int rs_360_ioctl(struct tty_struct *tty, struct file * file,
1409 unsigned int cmd, unsigned long arg)
1410{
1411 int error;
1412 ser_info_t *info = (ser_info_t *)tty->driver_data;
1413 int retval;
1414 struct async_icount cnow;
1415 /* struct async_icount_24 cnow;*/ /* kernel counter temps */
1416 struct serial_icounter_struct *p_cuser; /* user space */
1417
1418 if (serial_paranoia_check(info, tty->name, "rs_ioctl"))
1419 return -ENODEV;
1420
1421 if (cmd != TIOCMIWAIT) {
1422 if (tty->flags & (1 << TTY_IO_ERROR))
1423 return -EIO;
1424 }
1425
1426 switch (cmd) {
1427 case TCSBRK: /* SVID version: non-zero arg --> no break */
1428 retval = tty_check_change(tty);
1429 if (retval)
1430 return retval;
1431 tty_wait_until_sent(tty, 0);
1432 if (signal_pending(current))
1433 return -EINTR;
1434 if (!arg) {
1435 send_break(info, 250); /* 1/4 second */
1436 if (signal_pending(current))
1437 return -EINTR;
1438 }
1439 return 0;
1440 case TCSBRKP: /* support for POSIX tcsendbreak() */
1441 retval = tty_check_change(tty);
1442 if (retval)
1443 return retval;
1444 tty_wait_until_sent(tty, 0);
1445 if (signal_pending(current))
1446 return -EINTR;
1447 send_break(info, arg ? arg*100 : 250);
1448 if (signal_pending(current))
1449 return -EINTR;
1450 return 0;
1451 case TIOCSBRK:
1452 retval = tty_check_change(tty);
1453 if (retval)
1454 return retval;
1455 tty_wait_until_sent(tty, 0);
1456 begin_break(info);
1457 return 0;
1458 case TIOCCBRK:
1459 retval = tty_check_change(tty);
1460 if (retval)
1461 return retval;
1462 end_break(info);
1463 return 0;
1464#ifdef maybe
1465 case TIOCSERGETLSR: /* Get line status register */
1466 return get_lsr_info(info, (unsigned int *) arg);
1467#endif
1468 /*
1469 * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change
1470 * - mask passed in arg for lines of interest
1471 * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking)
1472 * Caller should use TIOCGICOUNT to see which one it was
1473 */
1474 case TIOCMIWAIT:
1475#ifdef modem_control
1476 local_irq_disable();
1477 /* note the counters on entry */
1478 cprev = info->state->icount;
1479 local_irq_enable();
1480 while (1) {
1481 interruptible_sleep_on(&info->delta_msr_wait);
1482 /* see if a signal did it */
1483 if (signal_pending(current))
1484 return -ERESTARTSYS;
1485 local_irq_disable();
1486 cnow = info->state->icount; /* atomic copy */
1487 local_irq_enable();
1488 if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
1489 cnow.dcd == cprev.dcd && cnow.cts == cprev.cts)
1490 return -EIO; /* no change => error */
1491 if ( ((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) ||
1492 ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) ||
1493 ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) ||
1494 ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts)) ) {
1495 return 0;
1496 }
1497 cprev = cnow;
1498 }
1499 /* NOTREACHED */
1500#else
1501 return 0;
1502#endif
1503
1504
1505 default:
1506 return -ENOIOCTLCMD;
1507 }
1508 return 0;
1509}
1510
1511/* FIX UP modem control here someday......
1512*/
1513static void rs_360_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
1514{
1515 ser_info_t *info = (ser_info_t *)tty->driver_data;
1516
1517 change_speed(info);
1518
1519#ifdef modem_control
1520 /* Handle transition to B0 status */
1521 if ((old_termios->c_cflag & CBAUD) &&
1522 !(tty->termios->c_cflag & CBAUD)) {
1523 info->MCR &= ~(UART_MCR_DTR|UART_MCR_RTS);
1524 local_irq_disable();
1525 serial_out(info, UART_MCR, info->MCR);
1526 local_irq_enable();
1527 }
1528
1529 /* Handle transition away from B0 status */
1530 if (!(old_termios->c_cflag & CBAUD) &&
1531 (tty->termios->c_cflag & CBAUD)) {
1532 info->MCR |= UART_MCR_DTR;
1533 if (!tty->hw_stopped ||
1534 !(tty->termios->c_cflag & CRTSCTS)) {
1535 info->MCR |= UART_MCR_RTS;
1536 }
1537 local_irq_disable();
1538 serial_out(info, UART_MCR, info->MCR);
1539 local_irq_enable();
1540 }
1541
1542 /* Handle turning off CRTSCTS */
1543 if ((old_termios->c_cflag & CRTSCTS) &&
1544 !(tty->termios->c_cflag & CRTSCTS)) {
1545 tty->hw_stopped = 0;
1546 rs_360_start(tty);
1547 }
1548#endif
1549
1550#if 0
1551 /*
1552 * No need to wake up processes in open wait, since they
1553 * sample the CLOCAL flag once, and don't recheck it.
1554 * XXX It's not clear whether the current behavior is correct
1555 * or not. Hence, this may change.....
1556 */
1557 if (!(old_termios->c_cflag & CLOCAL) &&
1558 (tty->termios->c_cflag & CLOCAL))
1559 wake_up_interruptible(&info->open_wait);
1560#endif
1561}
1562
1563/*
1564 * ------------------------------------------------------------
1565 * rs_close()
1566 *
1567 * This routine is called when the serial port gets closed. First, we
1568 * wait for the last remaining data to be sent. Then, we unlink its
1569 * async structure from the interrupt chain if necessary, and we free
1570 * that IRQ if nothing is left in the chain.
1571 * ------------------------------------------------------------
1572 */
1573static void rs_360_close(struct tty_struct *tty, struct file * filp)
1574{
1575 ser_info_t *info = (ser_info_t *)tty->driver_data;
1576 /* struct async_state *state; */
1577 struct serial_state *state;
1578 unsigned long flags;
1579 int idx;
1580 volatile struct smc_regs *smcp;
1581 volatile struct scc_regs *sccp;
1582
1583 if (!info || serial_paranoia_check(info, tty->name, "rs_close"))
1584 return;
1585
1586 state = info->state;
1587
1588 local_irq_save(flags);
1589
1590 if (tty_hung_up_p(filp)) {
1591 DBG_CNT("before DEC-hung");
1592 local_irq_restore(flags);
1593 return;
1594 }
1595
1596#ifdef SERIAL_DEBUG_OPEN
1597 printk("rs_close ttys%d, count = %d\n", info->line, state->count);
1598#endif
1599 if ((tty->count == 1) && (state->count != 1)) {
1600 /*
1601 * Uh, oh. tty->count is 1, which means that the tty
1602 * structure will be freed. state->count should always
1603 * be one in these conditions. If it's greater than
1604 * one, we've got real problems, since it means the
1605 * serial port won't be shutdown.
1606 */
1607 printk("rs_close: bad serial port count; tty->count is 1, "
1608 "state->count is %d\n", state->count);
1609 state->count = 1;
1610 }
1611 if (--state->count < 0) {
1612 printk("rs_close: bad serial port count for ttys%d: %d\n",
1613 info->line, state->count);
1614 state->count = 0;
1615 }
1616 if (state->count) {
1617 DBG_CNT("before DEC-2");
1618 local_irq_restore(flags);
1619 return;
1620 }
1621 info->flags |= ASYNC_CLOSING;
1622 /*
1623 * Now we wait for the transmit buffer to clear; and we notify
1624 * the line discipline to only process XON/XOFF characters.
1625 */
1626 tty->closing = 1;
1627 if (info->closing_wait != ASYNC_CLOSING_WAIT_NONE)
1628 tty_wait_until_sent(tty, info->closing_wait);
1629 /*
1630 * At this point we stop accepting input. To do this, we
1631 * disable the receive line status interrupts, and tell the
1632 * interrupt driver to stop checking the data ready bit in the
1633 * line status register.
1634 */
1635 info->read_status_mask &= ~BD_SC_EMPTY;
1636 if (info->flags & ASYNC_INITIALIZED) {
1637
1638 idx = PORT_NUM(info->state->smc_scc_num);
1639 if (info->state->smc_scc_num & NUM_IS_SCC) {
1640 sccp = &pquicc->scc_regs[idx];
1641 sccp->scc_sccm &= ~UART_SCCM_RX;
1642 sccp->scc_gsmr.w.low &= ~SCC_GSMRL_ENR;
1643 } else {
1644 smcp = &pquicc->smc_regs[idx];
1645 smcp->smc_smcm &= ~SMCM_RX;
1646 smcp->smc_smcmr &= ~SMCMR_REN;
1647 }
1648 /*
1649 * Before we drop DTR, make sure the UART transmitter
1650 * has completely drained; this is especially
1651 * important if there is a transmit FIFO!
1652 */
1653 rs_360_wait_until_sent(tty, info->timeout);
1654 }
1655 shutdown(info);
1656 rs_360_flush_buffer(tty);
1657 tty_ldisc_flush(tty);
1658 tty->closing = 0;
1659 info->event = 0;
1660 info->port.tty = NULL;
1661 if (info->blocked_open) {
1662 if (info->close_delay) {
1663 msleep_interruptible(jiffies_to_msecs(info->close_delay));
1664 }
1665 wake_up_interruptible(&info->open_wait);
1666 }
1667 info->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING);
1668 wake_up_interruptible(&info->close_wait);
1669 local_irq_restore(flags);
1670}
1671
1672/*
1673 * rs_wait_until_sent() --- wait until the transmitter is empty
1674 */
1675static void rs_360_wait_until_sent(struct tty_struct *tty, int timeout)
1676{
1677 ser_info_t *info = (ser_info_t *)tty->driver_data;
1678 unsigned long orig_jiffies, char_time;
1679 /*int lsr;*/
1680 volatile QUICC_BD *bdp;
1681
1682 if (serial_paranoia_check(info, tty->name, "rs_wait_until_sent"))
1683 return;
1684
1685#ifdef maybe
1686 if (info->state->type == PORT_UNKNOWN)
1687 return;
1688#endif
1689
1690 orig_jiffies = jiffies;
1691 /*
1692 * Set the check interval to be 1/5 of the estimated time to
1693 * send a single character, and make it at least 1. The check
1694 * interval should also be less than the timeout.
1695 *
1696 * Note: we have to use pretty tight timings here to satisfy
1697 * the NIST-PCTS.
1698 */
1699 char_time = 1;
1700 if (timeout)
1701 char_time = min(char_time, (unsigned long)timeout);
1702#ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT
1703 printk("In rs_wait_until_sent(%d) check=%lu...", timeout, char_time);
1704 printk("jiff=%lu...", jiffies);
1705#endif
1706
1707 /* We go through the loop at least once because we can't tell
1708 * exactly when the last character exits the shifter. There can
1709 * be at least two characters waiting to be sent after the buffers
1710 * are empty.
1711 */
1712 do {
1713#ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT
1714 printk("lsr = %d (jiff=%lu)...", lsr, jiffies);
1715#endif
1716/* current->counter = 0; make us low-priority */
1717 msleep_interruptible(jiffies_to_msecs(char_time));
1718 if (signal_pending(current))
1719 break;
1720 if (timeout && (time_after(jiffies, orig_jiffies + timeout)))
1721 break;
1722 /* The 'tx_cur' is really the next buffer to send. We
1723 * have to back up to the previous BD and wait for it
1724 * to go. This isn't perfect, because all this indicates
1725 * is the buffer is available. There are still characters
1726 * in the CPM FIFO.
1727 */
1728 bdp = info->tx_cur;
1729 if (bdp == info->tx_bd_base)
1730 bdp += (TX_NUM_FIFO-1);
1731 else
1732 bdp--;
1733 } while (bdp->status & BD_SC_READY);
1734 current->state = TASK_RUNNING;
1735#ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT
1736 printk("lsr = %d (jiff=%lu)...done\n", lsr, jiffies);
1737#endif
1738}
1739
1740/*
1741 * rs_hangup() --- called by tty_hangup() when a hangup is signaled.
1742 */
1743static void rs_360_hangup(struct tty_struct *tty)
1744{
1745 ser_info_t *info = (ser_info_t *)tty->driver_data;
1746 struct serial_state *state = info->state;
1747
1748 if (serial_paranoia_check(info, tty->name, "rs_hangup"))
1749 return;
1750
1751 state = info->state;
1752
1753 rs_360_flush_buffer(tty);
1754 shutdown(info);
1755 info->event = 0;
1756 state->count = 0;
1757 info->flags &= ~ASYNC_NORMAL_ACTIVE;
1758 info->port.tty = NULL;
1759 wake_up_interruptible(&info->open_wait);
1760}
1761
1762/*
1763 * ------------------------------------------------------------
1764 * rs_open() and friends
1765 * ------------------------------------------------------------
1766 */
1767static int block_til_ready(struct tty_struct *tty, struct file * filp,
1768 ser_info_t *info)
1769{
1770#ifdef DO_THIS_LATER
1771 DECLARE_WAITQUEUE(wait, current);
1772#endif
1773 struct serial_state *state = info->state;
1774 int retval;
1775 int do_clocal = 0;
1776
1777 /*
1778 * If the device is in the middle of being closed, then block
1779 * until it's done, and then try again.
1780 */
1781 if (tty_hung_up_p(filp) ||
1782 (info->flags & ASYNC_CLOSING)) {
1783 if (info->flags & ASYNC_CLOSING)
1784 interruptible_sleep_on(&info->close_wait);
1785#ifdef SERIAL_DO_RESTART
1786 if (info->flags & ASYNC_HUP_NOTIFY)
1787 return -EAGAIN;
1788 else
1789 return -ERESTARTSYS;
1790#else
1791 return -EAGAIN;
1792#endif
1793 }
1794
1795 /*
1796 * If non-blocking mode is set, or the port is not enabled,
1797 * then make the check up front and then exit.
1798 * If this is an SMC port, we don't have modem control to wait
1799 * for, so just get out here.
1800 */
1801 if ((filp->f_flags & O_NONBLOCK) ||
1802 (tty->flags & (1 << TTY_IO_ERROR)) ||
1803 !(info->state->smc_scc_num & NUM_IS_SCC)) {
1804 info->flags |= ASYNC_NORMAL_ACTIVE;
1805 return 0;
1806 }
1807
1808 if (tty->termios->c_cflag & CLOCAL)
1809 do_clocal = 1;
1810
1811 /*
1812 * Block waiting for the carrier detect and the line to become
1813 * free (i.e., not in use by the callout). While we are in
1814 * this loop, state->count is dropped by one, so that
1815 * rs_close() knows when to free things. We restore it upon
1816 * exit, either normal or abnormal.
1817 */
1818 retval = 0;
1819#ifdef DO_THIS_LATER
1820 add_wait_queue(&info->open_wait, &wait);
1821#ifdef SERIAL_DEBUG_OPEN
1822 printk("block_til_ready before block: ttys%d, count = %d\n",
1823 state->line, state->count);
1824#endif
1825 local_irq_disable();
1826 if (!tty_hung_up_p(filp))
1827 state->count--;
1828 local_irq_enable();
1829 info->blocked_open++;
1830 while (1) {
1831 local_irq_disable();
1832 if (tty->termios->c_cflag & CBAUD)
1833 serial_out(info, UART_MCR,
1834 serial_inp(info, UART_MCR) |
1835 (UART_MCR_DTR | UART_MCR_RTS));
1836 local_irq_enable();
1837 set_current_state(TASK_INTERRUPTIBLE);
1838 if (tty_hung_up_p(filp) ||
1839 !(info->flags & ASYNC_INITIALIZED)) {
1840#ifdef SERIAL_DO_RESTART
1841 if (info->flags & ASYNC_HUP_NOTIFY)
1842 retval = -EAGAIN;
1843 else
1844 retval = -ERESTARTSYS;
1845#else
1846 retval = -EAGAIN;
1847#endif
1848 break;
1849 }
1850 if (!(info->flags & ASYNC_CLOSING) &&
1851 (do_clocal || (serial_in(info, UART_MSR) &
1852 UART_MSR_DCD)))
1853 break;
1854 if (signal_pending(current)) {
1855 retval = -ERESTARTSYS;
1856 break;
1857 }
1858#ifdef SERIAL_DEBUG_OPEN
1859 printk("block_til_ready blocking: ttys%d, count = %d\n",
1860 info->line, state->count);
1861#endif
1862 tty_unlock();
1863 schedule();
1864 tty_lock();
1865 }
1866 current->state = TASK_RUNNING;
1867 remove_wait_queue(&info->open_wait, &wait);
1868 if (!tty_hung_up_p(filp))
1869 state->count++;
1870 info->blocked_open--;
1871#ifdef SERIAL_DEBUG_OPEN
1872 printk("block_til_ready after blocking: ttys%d, count = %d\n",
1873 info->line, state->count);
1874#endif
1875#endif /* DO_THIS_LATER */
1876 if (retval)
1877 return retval;
1878 info->flags |= ASYNC_NORMAL_ACTIVE;
1879 return 0;
1880}
1881
1882static int get_async_struct(int line, ser_info_t **ret_info)
1883{
1884 struct serial_state *sstate;
1885
1886 sstate = rs_table + line;
1887 if (sstate->info) {
1888 sstate->count++;
1889 *ret_info = (ser_info_t *)sstate->info;
1890 return 0;
1891 }
1892 else {
1893 return -ENOMEM;
1894 }
1895}
1896
1897/*
1898 * This routine is called whenever a serial port is opened. It
1899 * enables interrupts for a serial port, linking in its async structure into
1900 * the IRQ chain. It also performs the serial-specific
1901 * initialization for the tty structure.
1902 */
1903static int rs_360_open(struct tty_struct *tty, struct file * filp)
1904{
1905 ser_info_t *info;
1906 int retval, line;
1907
1908 line = tty->index;
1909 if ((line < 0) || (line >= NR_PORTS))
1910 return -ENODEV;
1911 retval = get_async_struct(line, &info);
1912 if (retval)
1913 return retval;
1914 if (serial_paranoia_check(info, tty->name, "rs_open"))
1915 return -ENODEV;
1916
1917#ifdef SERIAL_DEBUG_OPEN
1918 printk("rs_open %s, count = %d\n", tty->name, info->state->count);
1919#endif
1920 tty->driver_data = info;
1921 info->port.tty = tty;
1922
1923 /*
1924 * Start up serial port
1925 */
1926 retval = startup(info);
1927 if (retval)
1928 return retval;
1929
1930 retval = block_til_ready(tty, filp, info);
1931 if (retval) {
1932#ifdef SERIAL_DEBUG_OPEN
1933 printk("rs_open returning after block_til_ready with %d\n",
1934 retval);
1935#endif
1936 return retval;
1937 }
1938
1939#ifdef SERIAL_DEBUG_OPEN
1940 printk("rs_open %s successful...", tty->name);
1941#endif
1942 return 0;
1943}
1944
1945/*
1946 * /proc fs routines....
1947 */
1948
1949static inline int line_info(char *buf, struct serial_state *state)
1950{
1951#ifdef notdef
1952 struct async_struct *info = state->info, scr_info;
1953 char stat_buf[30], control, status;
1954#endif
1955 int ret;
1956
1957 ret = sprintf(buf, "%d: uart:%s port:%X irq:%d",
1958 state->line,
1959 (state->smc_scc_num & NUM_IS_SCC) ? "SCC" : "SMC",
1960 (unsigned int)(state->port), state->irq);
1961
1962 if (!state->port || (state->type == PORT_UNKNOWN)) {
1963 ret += sprintf(buf+ret, "\n");
1964 return ret;
1965 }
1966
1967#ifdef notdef
1968 /*
1969 * Figure out the current RS-232 lines
1970 */
1971 if (!info) {
1972 info = &scr_info; /* This is just for serial_{in,out} */
1973
1974 info->magic = SERIAL_MAGIC;
1975 info->port = state->port;
1976 info->flags = state->flags;
1977 info->quot = 0;
1978 info->port.tty = NULL;
1979 }
1980 local_irq_disable();
1981 status = serial_in(info, UART_MSR);
1982 control = info ? info->MCR : serial_in(info, UART_MCR);
1983 local_irq_enable();
1984
1985 stat_buf[0] = 0;
1986 stat_buf[1] = 0;
1987 if (control & UART_MCR_RTS)
1988 strcat(stat_buf, "|RTS");
1989 if (status & UART_MSR_CTS)
1990 strcat(stat_buf, "|CTS");
1991 if (control & UART_MCR_DTR)
1992 strcat(stat_buf, "|DTR");
1993 if (status & UART_MSR_DSR)
1994 strcat(stat_buf, "|DSR");
1995 if (status & UART_MSR_DCD)
1996 strcat(stat_buf, "|CD");
1997 if (status & UART_MSR_RI)
1998 strcat(stat_buf, "|RI");
1999
2000 if (info->quot) {
2001 ret += sprintf(buf+ret, " baud:%d",
2002 state->baud_base / info->quot);
2003 }
2004
2005 ret += sprintf(buf+ret, " tx:%d rx:%d",
2006 state->icount.tx, state->icount.rx);
2007
2008 if (state->icount.frame)
2009 ret += sprintf(buf+ret, " fe:%d", state->icount.frame);
2010
2011 if (state->icount.parity)
2012 ret += sprintf(buf+ret, " pe:%d", state->icount.parity);
2013
2014 if (state->icount.brk)
2015 ret += sprintf(buf+ret, " brk:%d", state->icount.brk);
2016
2017 if (state->icount.overrun)
2018 ret += sprintf(buf+ret, " oe:%d", state->icount.overrun);
2019
2020 /*
2021 * Last thing is the RS-232 status lines
2022 */
2023 ret += sprintf(buf+ret, " %s\n", stat_buf+1);
2024#endif
2025 return ret;
2026}
2027
2028int rs_360_read_proc(char *page, char **start, off_t off, int count,
2029 int *eof, void *data)
2030{
2031 int i, len = 0;
2032 off_t begin = 0;
2033
2034 len += sprintf(page, "serinfo:1.0 driver:%s\n", serial_version);
2035 for (i = 0; i < NR_PORTS && len < 4000; i++) {
2036 len += line_info(page + len, &rs_table[i]);
2037 if (len+begin > off+count)
2038 goto done;
2039 if (len+begin < off) {
2040 begin += len;
2041 len = 0;
2042 }
2043 }
2044 *eof = 1;
2045done:
2046 if (off >= len+begin)
2047 return 0;
2048 *start = page + (begin-off);
2049 return ((count < begin+len-off) ? count : begin+len-off);
2050}
2051
2052/*
2053 * ---------------------------------------------------------------------
2054 * rs_init() and friends
2055 *
2056 * rs_init() is called at boot-time to initialize the serial driver.
2057 * ---------------------------------------------------------------------
2058 */
2059
2060/*
2061 * This routine prints out the appropriate serial driver version
2062 * number, and identifies which options were configured into this
2063 * driver.
2064 */
2065static _INLINE_ void show_serial_version(void)
2066{
2067 printk(KERN_INFO "%s version %s\n", serial_name, serial_version);
2068}
2069
2070
2071/*
2072 * The serial console driver used during boot. Note that these names
2073 * clash with those found in "serial.c", so we currently can't support
2074 * the 16xxx uarts and these at the same time. I will fix this to become
2075 * an indirect function call from tty_io.c (or something).
2076 */
2077
2078#ifdef CONFIG_SERIAL_CONSOLE
2079
2080/*
2081 * Print a string to the serial port trying not to disturb any possible
2082 * real use of the port...
2083 */
2084static void my_console_write(int idx, const char *s,
2085 unsigned count)
2086{
2087 struct serial_state *ser;
2088 ser_info_t *info;
2089 unsigned i;
2090 QUICC_BD *bdp, *bdbase;
2091 volatile struct smc_uart_pram *up;
2092 volatile u_char *cp;
2093
2094 ser = rs_table + idx;
2095
2096
2097 /* If the port has been initialized for general use, we have
2098 * to use the buffer descriptors allocated there. Otherwise,
2099 * we simply use the single buffer allocated.
2100 */
2101 if ((info = (ser_info_t *)ser->info) != NULL) {
2102 bdp = info->tx_cur;
2103 bdbase = info->tx_bd_base;
2104 }
2105 else {
2106 /* Pointer to UART in parameter ram.
2107 */
2108 /* up = (smc_uart_t *)&cpmp->cp_dparam[ser->port]; */
2109 up = &pquicc->pram[ser->port].scc.pothers.idma_smc.psmc.u;
2110
2111 /* Get the address of the host memory buffer.
2112 */
2113 bdp = bdbase = (QUICC_BD *)((uint)pquicc + (uint)up->tbase);
2114 }
2115
2116 /*
2117 * We need to gracefully shut down the transmitter, disable
2118 * interrupts, then send our bytes out.
2119 */
2120
2121 /*
2122 * Now, do each character. This is not as bad as it looks
2123 * since this is a holding FIFO and not a transmitting FIFO.
2124 * We could add the complexity of filling the entire transmit
2125 * buffer, but we would just wait longer between accesses......
2126 */
2127 for (i = 0; i < count; i++, s++) {
2128 /* Wait for transmitter fifo to empty.
2129 * Ready indicates output is ready, and xmt is doing
2130 * that, not that it is ready for us to send.
2131 */
2132 while (bdp->status & BD_SC_READY);
2133
2134 /* Send the character out.
2135 */
2136 cp = bdp->buf;
2137 *cp = *s;
2138
2139 bdp->length = 1;
2140 bdp->status |= BD_SC_READY;
2141
2142 if (bdp->status & BD_SC_WRAP)
2143 bdp = bdbase;
2144 else
2145 bdp++;
2146
2147 /* if a LF, also do CR... */
2148 if (*s == 10) {
2149 while (bdp->status & BD_SC_READY);
2150 /* cp = __va(bdp->buf); */
2151 cp = bdp->buf;
2152 *cp = 13;
2153 bdp->length = 1;
2154 bdp->status |= BD_SC_READY;
2155
2156 if (bdp->status & BD_SC_WRAP) {
2157 bdp = bdbase;
2158 }
2159 else {
2160 bdp++;
2161 }
2162 }
2163 }
2164
2165 /*
2166 * Finally, Wait for transmitter & holding register to empty
2167 * and restore the IER
2168 */
2169 while (bdp->status & BD_SC_READY);
2170
2171 if (info)
2172 info->tx_cur = (QUICC_BD *)bdp;
2173}
2174
2175static void serial_console_write(struct console *c, const char *s,
2176 unsigned count)
2177{
2178#ifdef CONFIG_KGDB
2179 /* Try to let stub handle output. Returns true if it did. */
2180 if (kgdb_output_string(s, count))
2181 return;
2182#endif
2183 my_console_write(c->index, s, count);
2184}
2185
2186
2187
2188/*void console_print_68360(const char *p)
2189{
2190 const char *cp = p;
2191 int i;
2192
2193 for (i=0;cp[i]!=0;i++);
2194
2195 serial_console_write (p, i);
2196
2197 //Comment this if you want to have a strict interrupt-driven output
2198 //rs_fair_output();
2199
2200 return;
2201}*/
2202
2203
2204
2205
2206
2207
2208#ifdef CONFIG_XMON
2209int
2210xmon_360_write(const char *s, unsigned count)
2211{
2212 my_console_write(0, s, count);
2213 return(count);
2214}
2215#endif
2216
2217#ifdef CONFIG_KGDB
2218void
2219putDebugChar(char ch)
2220{
2221 my_console_write(0, &ch, 1);
2222}
2223#endif
2224
2225/*
2226 * Receive character from the serial port. This only works well
2227 * before the port is initialized for real use.
2228 */
2229static int my_console_wait_key(int idx, int xmon, char *obuf)
2230{
2231 struct serial_state *ser;
2232 u_char c, *cp;
2233 ser_info_t *info;
2234 QUICC_BD *bdp;
2235 volatile struct smc_uart_pram *up;
2236 int i;
2237
2238 ser = rs_table + idx;
2239
2240 /* Get the address of the host memory buffer.
2241 * If the port has been initialized for general use, we must
2242 * use information from the port structure.
2243 */
2244 if ((info = (ser_info_t *)ser->info))
2245 bdp = info->rx_cur;
2246 else
2247 /* bdp = (QUICC_BD *)&cpmp->cp_dpmem[up->smc_rbase]; */
2248 bdp = (QUICC_BD *)((uint)pquicc + (uint)up->tbase);
2249
2250 /* Pointer to UART in parameter ram.
2251 */
2252 /* up = (smc_uart_t *)&cpmp->cp_dparam[ser->port]; */
2253 up = &pquicc->pram[info->state->port].scc.pothers.idma_smc.psmc.u;
2254
2255 /*
2256 * We need to gracefully shut down the receiver, disable
2257 * interrupts, then read the input.
2258 * XMON just wants a poll. If no character, return -1, else
2259 * return the character.
2260 */
2261 if (!xmon) {
2262 while (bdp->status & BD_SC_EMPTY);
2263 }
2264 else {
2265 if (bdp->status & BD_SC_EMPTY)
2266 return -1;
2267 }
2268
2269 cp = (char *)bdp->buf;
2270
2271 if (obuf) {
2272 i = c = bdp->length;
2273 while (i-- > 0)
2274 *obuf++ = *cp++;
2275 }
2276 else {
2277 c = *cp;
2278 }
2279 bdp->status |= BD_SC_EMPTY;
2280
2281 if (info) {
2282 if (bdp->status & BD_SC_WRAP) {
2283 bdp = info->rx_bd_base;
2284 }
2285 else {
2286 bdp++;
2287 }
2288 info->rx_cur = (QUICC_BD *)bdp;
2289 }
2290
2291 return((int)c);
2292}
2293
2294static int serial_console_wait_key(struct console *co)
2295{
2296 return(my_console_wait_key(co->index, 0, NULL));
2297}
2298
2299#ifdef CONFIG_XMON
2300int
2301xmon_360_read_poll(void)
2302{
2303 return(my_console_wait_key(0, 1, NULL));
2304}
2305
2306int
2307xmon_360_read_char(void)
2308{
2309 return(my_console_wait_key(0, 0, NULL));
2310}
2311#endif
2312
2313#ifdef CONFIG_KGDB
2314static char kgdb_buf[RX_BUF_SIZE], *kgdp;
2315static int kgdb_chars;
2316
2317unsigned char
2318getDebugChar(void)
2319{
2320 if (kgdb_chars <= 0) {
2321 kgdb_chars = my_console_wait_key(0, 0, kgdb_buf);
2322 kgdp = kgdb_buf;
2323 }
2324 kgdb_chars--;
2325
2326 return(*kgdp++);
2327}
2328
2329void kgdb_interruptible(int state)
2330{
2331}
2332void kgdb_map_scc(void)
2333{
2334 struct serial_state *ser;
2335 uint mem_addr;
2336 volatile QUICC_BD *bdp;
2337 volatile smc_uart_t *up;
2338
2339 cpmp = (cpm360_t *)&(((immap_t *)IMAP_ADDR)->im_cpm);
2340
2341 /* To avoid data cache CPM DMA coherency problems, allocate a
2342 * buffer in the CPM DPRAM. This will work until the CPM and
2343 * serial ports are initialized. At that time a memory buffer
2344 * will be allocated.
2345 * The port is already initialized from the boot procedure, all
2346 * we do here is give it a different buffer and make it a FIFO.
2347 */
2348
2349 ser = rs_table;
2350
2351 /* Right now, assume we are using SMCs.
2352 */
2353 up = (smc_uart_t *)&cpmp->cp_dparam[ser->port];
2354
2355 /* Allocate space for an input FIFO, plus a few bytes for output.
2356 * Allocate bytes to maintain word alignment.
2357 */
2358 mem_addr = (uint)(&cpmp->cp_dpmem[0x1000]);
2359
2360 /* Set the physical address of the host memory buffers in
2361 * the buffer descriptors.
2362 */
2363 bdp = (QUICC_BD *)&cpmp->cp_dpmem[up->smc_rbase];
2364 bdp->buf = mem_addr;
2365
2366 bdp = (QUICC_BD *)&cpmp->cp_dpmem[up->smc_tbase];
2367 bdp->buf = mem_addr+RX_BUF_SIZE;
2368
2369 up->smc_mrblr = RX_BUF_SIZE; /* receive buffer length */
2370 up->smc_maxidl = RX_BUF_SIZE;
2371}
2372#endif
2373
2374static struct tty_struct *serial_console_device(struct console *c, int *index)
2375{
2376 *index = c->index;
2377 return serial_driver;
2378}
2379
2380
2381struct console sercons = {
2382 .name = "ttyS",
2383 .write = serial_console_write,
2384 .device = serial_console_device,
2385 .wait_key = serial_console_wait_key,
2386 .setup = serial_console_setup,
2387 .flags = CON_PRINTBUFFER,
2388 .index = CONFIG_SERIAL_CONSOLE_PORT,
2389};
2390
2391
2392
2393/*
2394 * Register console.
2395 */
2396long console_360_init(long kmem_start, long kmem_end)
2397{
2398 register_console(&sercons);
2399 /*register_console (console_print_68360); - 2.0.38 only required a write
2400 function pointer. */
2401 return kmem_start;
2402}
2403
2404#endif
2405
2406/* Index in baud rate table of the default console baud rate.
2407*/
2408static int baud_idx;
2409
2410static const struct tty_operations rs_360_ops = {
2411 .owner = THIS_MODULE,
2412 .open = rs_360_open,
2413 .close = rs_360_close,
2414 .write = rs_360_write,
2415 .put_char = rs_360_put_char,
2416 .write_room = rs_360_write_room,
2417 .chars_in_buffer = rs_360_chars_in_buffer,
2418 .flush_buffer = rs_360_flush_buffer,
2419 .ioctl = rs_360_ioctl,
2420 .throttle = rs_360_throttle,
2421 .unthrottle = rs_360_unthrottle,
2422 /* .send_xchar = rs_360_send_xchar, */
2423 .set_termios = rs_360_set_termios,
2424 .stop = rs_360_stop,
2425 .start = rs_360_start,
2426 .hangup = rs_360_hangup,
2427 /* .wait_until_sent = rs_360_wait_until_sent, */
2428 /* .read_proc = rs_360_read_proc, */
2429 .tiocmget = rs_360_tiocmget,
2430 .tiocmset = rs_360_tiocmset,
2431};
2432
2433static int __init rs_360_init(void)
2434{
2435 struct serial_state * state;
2436 ser_info_t *info;
2437 void *mem_addr;
2438 uint dp_addr, iobits;
2439 int i, j, idx;
2440 ushort chan;
2441 QUICC_BD *bdp;
2442 volatile QUICC *cp;
2443 volatile struct smc_regs *sp;
2444 volatile struct smc_uart_pram *up;
2445 volatile struct scc_regs *scp;
2446 volatile struct uart_pram *sup;
2447 /* volatile immap_t *immap; */
2448
2449 serial_driver = alloc_tty_driver(NR_PORTS);
2450 if (!serial_driver)
2451 return -1;
2452
2453 show_serial_version();
2454
2455 serial_driver->name = "ttyS";
2456 serial_driver->major = TTY_MAJOR;
2457 serial_driver->minor_start = 64;
2458 serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
2459 serial_driver->subtype = SERIAL_TYPE_NORMAL;
2460 serial_driver->init_termios = tty_std_termios;
2461 serial_driver->init_termios.c_cflag =
2462 baud_idx | CS8 | CREAD | HUPCL | CLOCAL;
2463 serial_driver->flags = TTY_DRIVER_REAL_RAW;
2464 tty_set_operations(serial_driver, &rs_360_ops);
2465
2466 if (tty_register_driver(serial_driver))
2467 panic("Couldn't register serial driver\n");
2468
2469 cp = pquicc; /* Get pointer to Communication Processor */
2470 /* immap = (immap_t *)IMAP_ADDR; */ /* and to internal registers */
2471
2472
2473 /* Configure SCC2, SCC3, and SCC4 instead of port A parallel I/O.
2474 */
2475 /* The "standard" configuration through the 860.
2476 */
2477/* immap->im_ioport.iop_papar |= 0x00fc; */
2478/* immap->im_ioport.iop_padir &= ~0x00fc; */
2479/* immap->im_ioport.iop_paodr &= ~0x00fc; */
2480 cp->pio_papar |= 0x00fc;
2481 cp->pio_padir &= ~0x00fc;
2482 /* cp->pio_paodr &= ~0x00fc; */
2483
2484
2485 /* Since we don't yet do modem control, connect the port C pins
2486 * as general purpose I/O. This will assert CTS and CD for the
2487 * SCC ports.
2488 */
2489 /* FIXME: see 360um p.7-365 and 860um p.34-12
2490 * I can't make sense of these bits - mleslie*/
2491/* immap->im_ioport.iop_pcdir |= 0x03c6; */
2492/* immap->im_ioport.iop_pcpar &= ~0x03c6; */
2493
2494/* cp->pio_pcdir |= 0x03c6; */
2495/* cp->pio_pcpar &= ~0x03c6; */
2496
2497
2498
2499 /* Connect SCC2 and SCC3 to NMSI. Connect BRG3 to SCC2 and
2500 * BRG4 to SCC3.
2501 */
2502 cp->si_sicr &= ~0x00ffff00;
2503 cp->si_sicr |= 0x001b1200;
2504
2505#ifdef CONFIG_PP04
2506 /* Frequentis PP04 forced to RS-232 until we know better.
2507 * Port C 12 and 13 low enables RS-232 on SCC3 and SCC4.
2508 */
2509 immap->im_ioport.iop_pcdir |= 0x000c;
2510 immap->im_ioport.iop_pcpar &= ~0x000c;
2511 immap->im_ioport.iop_pcdat &= ~0x000c;
2512
2513 /* This enables the TX driver.
2514 */
2515 cp->cp_pbpar &= ~0x6000;
2516 cp->cp_pbdat &= ~0x6000;
2517#endif
2518
2519 for (i = 0, state = rs_table; i < NR_PORTS; i++,state++) {
2520 state->magic = SSTATE_MAGIC;
2521 state->line = i;
2522 state->type = PORT_UNKNOWN;
2523 state->custom_divisor = 0;
2524 state->close_delay = 5*HZ/10;
2525 state->closing_wait = 30*HZ;
2526 state->icount.cts = state->icount.dsr =
2527 state->icount.rng = state->icount.dcd = 0;
2528 state->icount.rx = state->icount.tx = 0;
2529 state->icount.frame = state->icount.parity = 0;
2530 state->icount.overrun = state->icount.brk = 0;
2531 printk(KERN_INFO "ttyS%d at irq 0x%02x is an %s\n",
2532 i, (unsigned int)(state->irq),
2533 (state->smc_scc_num & NUM_IS_SCC) ? "SCC" : "SMC");
2534
2535#ifdef CONFIG_SERIAL_CONSOLE
2536 /* If we just printed the message on the console port, and
2537 * we are about to initialize it for general use, we have
2538 * to wait a couple of character times for the CR/NL to
2539 * make it out of the transmit buffer.
2540 */
2541 if (i == CONFIG_SERIAL_CONSOLE_PORT)
2542 mdelay(8);
2543
2544
2545/* idx = PORT_NUM(info->state->smc_scc_num); */
2546/* if (info->state->smc_scc_num & NUM_IS_SCC) */
2547/* chan = scc_chan_map[idx]; */
2548/* else */
2549/* chan = smc_chan_map[idx]; */
2550
2551/* cp->cp_cr = mk_cr_cmd(chan, CPM_CR_STOP_TX) | CPM_CR_FLG; */
2552/* while (cp->cp_cr & CPM_CR_FLG); */
2553
2554#endif
2555 /* info = kmalloc(sizeof(ser_info_t), GFP_KERNEL); */
2556 info = &quicc_ser_info[i];
2557 if (info) {
2558 memset (info, 0, sizeof(ser_info_t));
2559 info->magic = SERIAL_MAGIC;
2560 info->line = i;
2561 info->flags = state->flags;
2562 INIT_WORK(&info->tqueue, do_softint, info);
2563 INIT_WORK(&info->tqueue_hangup, do_serial_hangup, info);
2564 init_waitqueue_head(&info->open_wait);
2565 init_waitqueue_head(&info->close_wait);
2566 info->state = state;
2567 state->info = (struct async_struct *)info;
2568
2569 /* We need to allocate a transmit and receive buffer
2570 * descriptors from dual port ram, and a character
2571 * buffer area from host mem.
2572 */
2573 dp_addr = m360_cpm_dpalloc(sizeof(QUICC_BD) * RX_NUM_FIFO);
2574
2575 /* Allocate space for FIFOs in the host memory.
2576 * (for now this is from a static array of buffers :(
2577 */
2578 /* mem_addr = m360_cpm_hostalloc(RX_NUM_FIFO * RX_BUF_SIZE); */
2579 /* mem_addr = kmalloc (RX_NUM_FIFO * RX_BUF_SIZE, GFP_BUFFER); */
2580 mem_addr = &rx_buf_pool[i * RX_NUM_FIFO * RX_BUF_SIZE];
2581
2582 /* Set the physical address of the host memory
2583 * buffers in the buffer descriptors, and the
2584 * virtual address for us to work with.
2585 */
2586 bdp = (QUICC_BD *)((uint)pquicc + dp_addr);
2587 info->rx_cur = info->rx_bd_base = bdp;
2588
2589 /* initialize rx buffer descriptors */
2590 for (j=0; j<(RX_NUM_FIFO-1); j++) {
2591 bdp->buf = &rx_buf_pool[(i * RX_NUM_FIFO + j ) * RX_BUF_SIZE];
2592 bdp->status = BD_SC_EMPTY | BD_SC_INTRPT;
2593 mem_addr += RX_BUF_SIZE;
2594 bdp++;
2595 }
2596 bdp->buf = &rx_buf_pool[(i * RX_NUM_FIFO + j ) * RX_BUF_SIZE];
2597 bdp->status = BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT;
2598
2599
2600 idx = PORT_NUM(info->state->smc_scc_num);
2601 if (info->state->smc_scc_num & NUM_IS_SCC) {
2602
2603#if defined (CONFIG_UCQUICC) && 1
2604 /* set the transceiver mode to RS232 */
2605 sipex_mode_bits &= ~(uint)SIPEX_MODE(idx,0x0f); /* clear current mode */
2606 sipex_mode_bits |= (uint)SIPEX_MODE(idx,0x02);
2607 *(uint *)_periph_base = sipex_mode_bits;
2608 /* printk ("sipex bits = 0x%08x\n", sipex_mode_bits); */
2609#endif
2610 }
2611
2612 dp_addr = m360_cpm_dpalloc(sizeof(QUICC_BD) * TX_NUM_FIFO);
2613
2614 /* Allocate space for FIFOs in the host memory.
2615 */
2616 /* mem_addr = m360_cpm_hostalloc(TX_NUM_FIFO * TX_BUF_SIZE); */
2617 /* mem_addr = kmalloc (TX_NUM_FIFO * TX_BUF_SIZE, GFP_BUFFER); */
2618 mem_addr = &tx_buf_pool[i * TX_NUM_FIFO * TX_BUF_SIZE];
2619
2620 /* Set the physical address of the host memory
2621 * buffers in the buffer descriptors, and the
2622 * virtual address for us to work with.
2623 */
2624 /* bdp = (QUICC_BD *)&cp->cp_dpmem[dp_addr]; */
2625 bdp = (QUICC_BD *)((uint)pquicc + dp_addr);
2626 info->tx_cur = info->tx_bd_base = (QUICC_BD *)bdp;
2627
2628 /* initialize tx buffer descriptors */
2629 for (j=0; j<(TX_NUM_FIFO-1); j++) {
2630 bdp->buf = &tx_buf_pool[(i * TX_NUM_FIFO + j ) * TX_BUF_SIZE];
2631 bdp->status = BD_SC_INTRPT;
2632 mem_addr += TX_BUF_SIZE;
2633 bdp++;
2634 }
2635 bdp->buf = &tx_buf_pool[(i * TX_NUM_FIFO + j ) * TX_BUF_SIZE];
2636 bdp->status = (BD_SC_WRAP | BD_SC_INTRPT);
2637
2638 if (info->state->smc_scc_num & NUM_IS_SCC) {
2639 scp = &pquicc->scc_regs[idx];
2640 sup = &pquicc->pram[info->state->port].scc.pscc.u;
2641 sup->rbase = dp_addr;
2642 sup->tbase = dp_addr;
2643
2644 /* Set up the uart parameters in the
2645 * parameter ram.
2646 */
2647 sup->rfcr = SMC_EB;
2648 sup->tfcr = SMC_EB;
2649
2650 /* Set this to 1 for now, so we get single
2651 * character interrupts. Using idle character
2652 * time requires some additional tuning.
2653 */
2654 sup->mrblr = 1;
2655 sup->max_idl = 0;
2656 sup->brkcr = 1;
2657 sup->parec = 0;
2658 sup->frmer = 0;
2659 sup->nosec = 0;
2660 sup->brkec = 0;
2661 sup->uaddr1 = 0;
2662 sup->uaddr2 = 0;
2663 sup->toseq = 0;
2664 {
2665 int i;
2666 for (i=0;i<8;i++)
2667 sup->cc[i] = 0x8000;
2668 }
2669 sup->rccm = 0xc0ff;
2670
2671 /* Send the CPM an initialize command.
2672 */
2673 chan = scc_chan_map[idx];
2674
2675 /* execute the INIT RX & TX PARAMS command for this channel. */
2676 cp->cp_cr = mk_cr_cmd(chan, CPM_CR_INIT_TRX) | CPM_CR_FLG;
2677 while (cp->cp_cr & CPM_CR_FLG);
2678
2679 /* Set UART mode, 8 bit, no parity, one stop.
2680 * Enable receive and transmit.
2681 */
2682 scp->scc_gsmr.w.high = 0;
2683 scp->scc_gsmr.w.low =
2684 (SCC_GSMRL_MODE_UART | SCC_GSMRL_TDCR_16 | SCC_GSMRL_RDCR_16);
2685
2686 /* Disable all interrupts and clear all pending
2687 * events.
2688 */
2689 scp->scc_sccm = 0;
2690 scp->scc_scce = 0xffff;
2691 scp->scc_dsr = 0x7e7e;
2692 scp->scc_psmr = 0x3000;
2693
2694 /* If the port is the console, enable Rx and Tx.
2695 */
2696#ifdef CONFIG_SERIAL_CONSOLE
2697 if (i == CONFIG_SERIAL_CONSOLE_PORT)
2698 scp->scc_gsmr.w.low |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT);
2699#endif
2700 }
2701 else {
2702 /* Configure SMCs Tx/Rx instead of port B
2703 * parallel I/O.
2704 */
2705 up = &pquicc->pram[info->state->port].scc.pothers.idma_smc.psmc.u;
2706 up->rbase = dp_addr;
2707
2708 iobits = 0xc0 << (idx * 4);
2709 cp->pip_pbpar |= iobits;
2710 cp->pip_pbdir &= ~iobits;
2711 cp->pip_pbodr &= ~iobits;
2712
2713
2714 /* Connect the baud rate generator to the
2715 * SMC based upon index in rs_table. Also
2716 * make sure it is connected to NMSI.
2717 */
2718 cp->si_simode &= ~(0xffff << (idx * 16));
2719 cp->si_simode |= (i << ((idx * 16) + 12));
2720
2721 up->tbase = dp_addr;
2722
2723 /* Set up the uart parameters in the
2724 * parameter ram.
2725 */
2726 up->rfcr = SMC_EB;
2727 up->tfcr = SMC_EB;
2728
2729 /* Set this to 1 for now, so we get single
2730 * character interrupts. Using idle character
2731 * time requires some additional tuning.
2732 */
2733 up->mrblr = 1;
2734 up->max_idl = 0;
2735 up->brkcr = 1;
2736
2737 /* Send the CPM an initialize command.
2738 */
2739 chan = smc_chan_map[idx];
2740
2741 cp->cp_cr = mk_cr_cmd(chan,
2742 CPM_CR_INIT_TRX) | CPM_CR_FLG;
2743#ifdef CONFIG_SERIAL_CONSOLE
2744 if (i == CONFIG_SERIAL_CONSOLE_PORT)
2745 printk("");
2746#endif
2747 while (cp->cp_cr & CPM_CR_FLG);
2748
2749 /* Set UART mode, 8 bit, no parity, one stop.
2750 * Enable receive and transmit.
2751 */
2752 sp = &cp->smc_regs[idx];
2753 sp->smc_smcmr = smcr_mk_clen(9) | SMCMR_SM_UART;
2754
2755 /* Disable all interrupts and clear all pending
2756 * events.
2757 */
2758 sp->smc_smcm = 0;
2759 sp->smc_smce = 0xff;
2760
2761 /* If the port is the console, enable Rx and Tx.
2762 */
2763#ifdef CONFIG_SERIAL_CONSOLE
2764 if (i == CONFIG_SERIAL_CONSOLE_PORT)
2765 sp->smc_smcmr |= SMCMR_REN | SMCMR_TEN;
2766#endif
2767 }
2768
2769 /* Install interrupt handler.
2770 */
2771 /* cpm_install_handler(IRQ_MACHSPEC | state->irq, rs_360_interrupt, info); */
2772 /*request_irq(IRQ_MACHSPEC | state->irq, rs_360_interrupt, */
2773 request_irq(state->irq, rs_360_interrupt,
2774 IRQ_FLG_LOCK, "ttyS", (void *)info);
2775
2776 /* Set up the baud rate generator.
2777 */
2778 m360_cpm_setbrg(i, baud_table[baud_idx]);
2779
2780 }
2781 }
2782
2783 return 0;
2784}
2785module_init(rs_360_init);
2786
2787/* This must always be called before the rs_360_init() function, otherwise
2788 * it blows away the port control information.
2789 */
2790//static int __init serial_console_setup( struct console *co, char *options)
2791int serial_console_setup( struct console *co, char *options)
2792{
2793 struct serial_state *ser;
2794 uint mem_addr, dp_addr, bidx, idx, iobits;
2795 ushort chan;
2796 QUICC_BD *bdp;
2797 volatile QUICC *cp;
2798 volatile struct smc_regs *sp;
2799 volatile struct scc_regs *scp;
2800 volatile struct smc_uart_pram *up;
2801 volatile struct uart_pram *sup;
2802
2803/* mleslie TODO:
2804 * add something to the 68k bootloader to store a desired initial console baud rate */
2805
2806/* bd_t *bd; */ /* a board info struct used by EPPC-bug */
2807/* bd = (bd_t *)__res; */
2808
2809 for (bidx = 0; bidx < (sizeof(baud_table) / sizeof(int)); bidx++)
2810 /* if (bd->bi_baudrate == baud_table[bidx]) */
2811 if (CONSOLE_BAUDRATE == baud_table[bidx])
2812 break;
2813
2814 /* co->cflag = CREAD|CLOCAL|bidx|CS8; */
2815 baud_idx = bidx;
2816
2817 ser = rs_table + CONFIG_SERIAL_CONSOLE_PORT;
2818
2819 cp = pquicc; /* Get pointer to Communication Processor */
2820
2821 idx = PORT_NUM(ser->smc_scc_num);
2822 if (ser->smc_scc_num & NUM_IS_SCC) {
2823
2824 /* TODO: need to set up SCC pin assignment etc. here */
2825
2826 }
2827 else {
2828 iobits = 0xc0 << (idx * 4);
2829 cp->pip_pbpar |= iobits;
2830 cp->pip_pbdir &= ~iobits;
2831 cp->pip_pbodr &= ~iobits;
2832
2833 /* Connect the baud rate generator to the
2834 * SMC based upon index in rs_table. Also
2835 * make sure it is connected to NMSI.
2836 */
2837 cp->si_simode &= ~(0xffff << (idx * 16));
2838 cp->si_simode |= (idx << ((idx * 16) + 12));
2839 }
2840
2841 /* When we get here, the CPM has been reset, so we need
2842 * to configure the port.
2843 * We need to allocate a transmit and receive buffer descriptor
2844 * from dual port ram, and a character buffer area from host mem.
2845 */
2846
2847 /* Allocate space for two buffer descriptors in the DP ram.
2848 */
2849 dp_addr = m360_cpm_dpalloc(sizeof(QUICC_BD) * CONSOLE_NUM_FIFO);
2850
2851 /* Allocate space for two 2 byte FIFOs in the host memory.
2852 */
2853 /* mem_addr = m360_cpm_hostalloc(8); */
2854 mem_addr = (uint)console_fifos;
2855
2856
2857 /* Set the physical address of the host memory buffers in
2858 * the buffer descriptors.
2859 */
2860 /* bdp = (QUICC_BD *)&cp->cp_dpmem[dp_addr]; */
2861 bdp = (QUICC_BD *)((uint)pquicc + dp_addr);
2862 bdp->buf = (char *)mem_addr;
2863 (bdp+1)->buf = (char *)(mem_addr+4);
2864
2865 /* For the receive, set empty and wrap.
2866 * For transmit, set wrap.
2867 */
2868 bdp->status = BD_SC_EMPTY | BD_SC_WRAP;
2869 (bdp+1)->status = BD_SC_WRAP;
2870
2871 /* Set up the uart parameters in the parameter ram.
2872 */
2873 if (ser->smc_scc_num & NUM_IS_SCC) {
2874 scp = &cp->scc_regs[idx];
2875 /* sup = (scc_uart_t *)&cp->cp_dparam[ser->port]; */
2876 sup = &pquicc->pram[ser->port].scc.pscc.u;
2877
2878 sup->rbase = dp_addr;
2879 sup->tbase = dp_addr + sizeof(QUICC_BD);
2880
2881 /* Set up the uart parameters in the
2882 * parameter ram.
2883 */
2884 sup->rfcr = SMC_EB;
2885 sup->tfcr = SMC_EB;
2886
2887 /* Set this to 1 for now, so we get single
2888 * character interrupts. Using idle character
2889 * time requires some additional tuning.
2890 */
2891 sup->mrblr = 1;
2892 sup->max_idl = 0;
2893 sup->brkcr = 1;
2894 sup->parec = 0;
2895 sup->frmer = 0;
2896 sup->nosec = 0;
2897 sup->brkec = 0;
2898 sup->uaddr1 = 0;
2899 sup->uaddr2 = 0;
2900 sup->toseq = 0;
2901 {
2902 int i;
2903 for (i=0;i<8;i++)
2904 sup->cc[i] = 0x8000;
2905 }
2906 sup->rccm = 0xc0ff;
2907
2908 /* Send the CPM an initialize command.
2909 */
2910 chan = scc_chan_map[idx];
2911
2912 cp->cp_cr = mk_cr_cmd(chan, CPM_CR_INIT_TRX) | CPM_CR_FLG;
2913 while (cp->cp_cr & CPM_CR_FLG);
2914
2915 /* Set UART mode, 8 bit, no parity, one stop.
2916 * Enable receive and transmit.
2917 */
2918 scp->scc_gsmr.w.high = 0;
2919 scp->scc_gsmr.w.low =
2920 (SCC_GSMRL_MODE_UART | SCC_GSMRL_TDCR_16 | SCC_GSMRL_RDCR_16);
2921
2922 /* Disable all interrupts and clear all pending
2923 * events.
2924 */
2925 scp->scc_sccm = 0;
2926 scp->scc_scce = 0xffff;
2927 scp->scc_dsr = 0x7e7e;
2928 scp->scc_psmr = 0x3000;
2929
2930 scp->scc_gsmr.w.low |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT);
2931
2932 }
2933 else {
2934 /* up = (smc_uart_t *)&cp->cp_dparam[ser->port]; */
2935 up = &pquicc->pram[ser->port].scc.pothers.idma_smc.psmc.u;
2936
2937 up->rbase = dp_addr; /* Base of receive buffer desc. */
2938 up->tbase = dp_addr+sizeof(QUICC_BD); /* Base of xmt buffer desc. */
2939 up->rfcr = SMC_EB;
2940 up->tfcr = SMC_EB;
2941
2942 /* Set this to 1 for now, so we get single character interrupts.
2943 */
2944 up->mrblr = 1; /* receive buffer length */
2945 up->max_idl = 0; /* wait forever for next char */
2946
2947 /* Send the CPM an initialize command.
2948 */
2949 chan = smc_chan_map[idx];
2950 cp->cp_cr = mk_cr_cmd(chan, CPM_CR_INIT_TRX) | CPM_CR_FLG;
2951 while (cp->cp_cr & CPM_CR_FLG);
2952
2953 /* Set UART mode, 8 bit, no parity, one stop.
2954 * Enable receive and transmit.
2955 */
2956 sp = &cp->smc_regs[idx];
2957 sp->smc_smcmr = smcr_mk_clen(9) | SMCMR_SM_UART;
2958
2959 /* And finally, enable Rx and Tx.
2960 */
2961 sp->smc_smcmr |= SMCMR_REN | SMCMR_TEN;
2962 }
2963
2964 /* Set up the baud rate generator.
2965 */
2966 /* m360_cpm_setbrg((ser - rs_table), bd->bi_baudrate); */
2967 m360_cpm_setbrg((ser - rs_table), CONSOLE_BAUDRATE);
2968
2969 return 0;
2970}
2971
2972/*
2973 * Local variables:
2974 * c-indent-level: 4
2975 * c-basic-offset: 4
2976 * tab-width: 4
2977 * End:
2978 */
generated by cgit v1.2.2 (git 2.25.0) at 2026-01-03 10:59:47 -0500