1 files changed, 434 insertions, 0 deletions

diff --git a/drivers/spi/xilinx_spi.c b/drivers/spi/xilinx_spi.c
new file mode 100644
index 000000000000..f0bf9a68e96b
--- /dev/null
+++ b/drivers/spi/xilinx_spi.c
@@ -0,0 +1,434 @@
+/*
+ * xilinx_spi.c
+ *
+ * Xilinx SPI controller driver (master mode only)
+ *
+ * Author: MontaVista Software, Inc.
+ *      source@mvista.com
+ *
+ * 2002-2007 (c) MontaVista Software, Inc.  This file is licensed under the
+ * terms of the GNU General Public License version 2.  This program is licensed
+ * "as is" without any warranty of any kind, whether express or implied.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi_bitbang.h>
+#include <linux/io.h>
+
+#include <syslib/virtex_devices.h>
+
+#define XILINX_SPI_NAME "xspi"
+
+/* Register definitions as per "OPB Serial Peripheral Interface (SPI) (v1.00e)
+ * Product Specification", DS464
+ */
+#define XSPI_CR_OFFSET          0x62    /* 16-bit Control Register */
+
+#define XSPI_CR_ENABLE          0x02
+#define XSPI_CR_MASTER_MODE     0x04
+#define XSPI_CR_CPOL            0x08
+#define XSPI_CR_CPHA            0x10
+#define XSPI_CR_MODE_MASK       (XSPI_CR_CPHA | XSPI_CR_CPOL)
+#define XSPI_CR_TXFIFO_RESET    0x20
+#define XSPI_CR_RXFIFO_RESET    0x40
+#define XSPI_CR_MANUAL_SSELECT  0x80
+#define XSPI_CR_TRANS_INHIBIT   0x100
+
+#define XSPI_SR_OFFSET          0x67    /* 8-bit Status Register */
+
+#define XSPI_SR_RX_EMPTY_MASK   0x01    /* Receive FIFO is empty */
+#define XSPI_SR_RX_FULL_MASK    0x02    /* Receive FIFO is full */
+#define XSPI_SR_TX_EMPTY_MASK   0x04    /* Transmit FIFO is empty */
+#define XSPI_SR_TX_FULL_MASK    0x08    /* Transmit FIFO is full */
+#define XSPI_SR_MODE_FAULT_MASK 0x10    /* Mode fault error */
+
+#define XSPI_TXD_OFFSET         0x6b    /* 8-bit Data Transmit Register */
+#define XSPI_RXD_OFFSET         0x6f    /* 8-bit Data Receive Register */
+
+#define XSPI_SSR_OFFSET         0x70    /* 32-bit Slave Select Register */
+
+/* Register definitions as per "OPB IPIF (v3.01c) Product Specification", DS414
+ * IPIF registers are 32 bit
+ */
+#define XIPIF_V123B_DGIER_OFFSET        0x1c    /* IPIF global int enable reg */
+#define XIPIF_V123B_GINTR_ENABLE        0x80000000
+
+#define XIPIF_V123B_IISR_OFFSET         0x20    /* IPIF interrupt status reg */
+#define XIPIF_V123B_IIER_OFFSET         0x28    /* IPIF interrupt enable reg */
+
+#define XSPI_INTR_MODE_FAULT            0x01    /* Mode fault error */
+#define XSPI_INTR_SLAVE_MODE_FAULT      0x02    /* Selected as slave while
+                                                 * disabled */
+#define XSPI_INTR_TX_EMPTY              0x04    /* TxFIFO is empty */
+#define XSPI_INTR_TX_UNDERRUN           0x08    /* TxFIFO was underrun */
+#define XSPI_INTR_RX_FULL               0x10    /* RxFIFO is full */
+#define XSPI_INTR_RX_OVERRUN            0x20    /* RxFIFO was overrun */
+
+#define XIPIF_V123B_RESETR_OFFSET       0x40    /* IPIF reset register */
+#define XIPIF_V123B_RESET_MASK          0x0a    /* the value to write */
+
+struct xilinx_spi {
+        /* bitbang has to be first */
+        struct spi_bitbang bitbang;
+        struct completion done;
+
+        void __iomem    *regs;  /* virt. address of the control registers */
+
+        u32             irq;
+
+        u32             speed_hz; /* SCK has a fixed frequency of speed_hz Hz */
+
+        u8 *rx_ptr;             /* pointer in the Tx buffer */
+        const u8 *tx_ptr;       /* pointer in the Rx buffer */
+        int remaining_bytes;    /* the number of bytes left to transfer */
+};
+
+static void xspi_init_hw(void __iomem *regs_base)
+{
+        /* Reset the SPI device */
+        out_be32(regs_base + XIPIF_V123B_RESETR_OFFSET,
+                 XIPIF_V123B_RESET_MASK);
+        /* Disable all the interrupts just in case */
+        out_be32(regs_base + XIPIF_V123B_IIER_OFFSET, 0);
+        /* Enable the global IPIF interrupt */
+        out_be32(regs_base + XIPIF_V123B_DGIER_OFFSET,
+                 XIPIF_V123B_GINTR_ENABLE);
+        /* Deselect the slave on the SPI bus */
+        out_be32(regs_base + XSPI_SSR_OFFSET, 0xffff);
+        /* Disable the transmitter, enable Manual Slave Select Assertion,
+         * put SPI controller into master mode, and enable it */
+        out_be16(regs_base + XSPI_CR_OFFSET,
+                 XSPI_CR_TRANS_INHIBIT | XSPI_CR_MANUAL_SSELECT
+                 | XSPI_CR_MASTER_MODE | XSPI_CR_ENABLE);
+}
+
+static void xilinx_spi_chipselect(struct spi_device *spi, int is_on)
+{
+        struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
+
+        if (is_on == BITBANG_CS_INACTIVE) {
+                /* Deselect the slave on the SPI bus */
+                out_be32(xspi->regs + XSPI_SSR_OFFSET, 0xffff);
+        } else if (is_on == BITBANG_CS_ACTIVE) {
+                /* Set the SPI clock phase and polarity */
+                u16 cr = in_be16(xspi->regs + XSPI_CR_OFFSET)
+                         & ~XSPI_CR_MODE_MASK;
+                if (spi->mode & SPI_CPHA)
+                        cr |= XSPI_CR_CPHA;
+                if (spi->mode & SPI_CPOL)
+                        cr |= XSPI_CR_CPOL;
+                out_be16(xspi->regs + XSPI_CR_OFFSET, cr);
+
+                /* We do not check spi->max_speed_hz here as the SPI clock
+                 * frequency is not software programmable (the IP block design
+                 * parameter)
+                 */
+
+                /* Activate the chip select */
+                out_be32(xspi->regs + XSPI_SSR_OFFSET,
+                         ~(0x0001 << spi->chip_select));
+        }
+}
+
+/* spi_bitbang requires custom setup_transfer() to be defined if there is a
+ * custom txrx_bufs(). We have nothing to setup here as the SPI IP block
+ * supports just 8 bits per word, and SPI clock can't be changed in software.
+ * Check for 8 bits per word. Chip select delay calculations could be
+ * added here as soon as bitbang_work() can be made aware of the delay value.
+ */
+static int xilinx_spi_setup_transfer(struct spi_device *spi,
+                struct spi_transfer *t)
+{
+        u8 bits_per_word;
+        u32 hz;
+        struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
+
+        bits_per_word = (t) ? t->bits_per_word : spi->bits_per_word;
+        hz = (t) ? t->speed_hz : spi->max_speed_hz;
+        if (bits_per_word != 8) {
+                dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n",
+                        __FUNCTION__, bits_per_word);
+                return -EINVAL;
+        }
+
+        if (hz && xspi->speed_hz > hz) {
+                dev_err(&spi->dev, "%s, unsupported clock rate %uHz\n",
+                        __FUNCTION__, hz);
+                return -EINVAL;
+        }
+
+        return 0;
+}
+
+/* the spi->mode bits understood by this driver: */
+#define MODEBITS (SPI_CPOL | SPI_CPHA)
+
+static int xilinx_spi_setup(struct spi_device *spi)
+{
+        struct spi_bitbang *bitbang;
+        struct xilinx_spi *xspi;
+        int retval;
+
+        xspi = spi_master_get_devdata(spi->master);
+        bitbang = &xspi->bitbang;
+
+        if (!spi->bits_per_word)
+                spi->bits_per_word = 8;
+
+        if (spi->mode & ~MODEBITS) {
+                dev_err(&spi->dev, "%s, unsupported mode bits %x\n",
+                        __FUNCTION__, spi->mode & ~MODEBITS);
+                return -EINVAL;
+        }
+
+        retval = xilinx_spi_setup_transfer(spi, NULL);
+        if (retval < 0)
+                return retval;
+
+        dev_dbg(&spi->dev, "%s, mode %d, %u bits/w, %u nsec/bit\n",
+                __FUNCTION__, spi->mode & MODEBITS, spi->bits_per_word, 0);
+
+        return 0;
+}
+
+static void xilinx_spi_fill_tx_fifo(struct xilinx_spi *xspi)
+{
+        u8 sr;
+
+        /* Fill the Tx FIFO with as many bytes as possible */
+        sr = in_8(xspi->regs + XSPI_SR_OFFSET);
+        while ((sr & XSPI_SR_TX_FULL_MASK) == 0 && xspi->remaining_bytes > 0) {
+                if (xspi->tx_ptr) {
+                        out_8(xspi->regs + XSPI_TXD_OFFSET, *xspi->tx_ptr++);
+                } else {
+                        out_8(xspi->regs + XSPI_TXD_OFFSET, 0);
+                }
+                xspi->remaining_bytes--;
+                sr = in_8(xspi->regs + XSPI_SR_OFFSET);
+        }
+}
+
+static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
+{
+        struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
+        u32 ipif_ier;
+        u16 cr;
+
+        /* We get here with transmitter inhibited */
+
+        xspi->tx_ptr = t->tx_buf;
+        xspi->rx_ptr = t->rx_buf;
+        xspi->remaining_bytes = t->len;
+        INIT_COMPLETION(xspi->done);
+
+        xilinx_spi_fill_tx_fifo(xspi);
+
+        /* Enable the transmit empty interrupt, which we use to determine
+         * progress on the transmission.
+         */
+        ipif_ier = in_be32(xspi->regs + XIPIF_V123B_IIER_OFFSET);
+        out_be32(xspi->regs + XIPIF_V123B_IIER_OFFSET,
+                 ipif_ier | XSPI_INTR_TX_EMPTY);
+
+        /* Start the transfer by not inhibiting the transmitter any longer */
+        cr = in_be16(xspi->regs + XSPI_CR_OFFSET) & ~XSPI_CR_TRANS_INHIBIT;
+        out_be16(xspi->regs + XSPI_CR_OFFSET, cr);
+
+        wait_for_completion(&xspi->done);
+
+        /* Disable the transmit empty interrupt */
+        out_be32(xspi->regs + XIPIF_V123B_IIER_OFFSET, ipif_ier);
+
+        return t->len - xspi->remaining_bytes;
+}
+
+
+/* This driver supports single master mode only. Hence Tx FIFO Empty
+ * is the only interrupt we care about.
+ * Receive FIFO Overrun, Transmit FIFO Underrun, Mode Fault, and Slave Mode
+ * Fault are not to happen.
+ */
+static irqreturn_t xilinx_spi_irq(int irq, void *dev_id)
+{
+        struct xilinx_spi *xspi = dev_id;
+        u32 ipif_isr;
+
+        /* Get the IPIF interrupts, and clear them immediately */
+        ipif_isr = in_be32(xspi->regs + XIPIF_V123B_IISR_OFFSET);
+        out_be32(xspi->regs + XIPIF_V123B_IISR_OFFSET, ipif_isr);
+
+        if (ipif_isr & XSPI_INTR_TX_EMPTY) {    /* Transmission completed */
+                u16 cr;
+                u8 sr;
+
+                /* A transmit has just completed. Process received data and
+                 * check for more data to transmit. Always inhibit the
+                 * transmitter while the Isr refills the transmit register/FIFO,
+                 * or make sure it is stopped if we're done.
+                 */
+                cr = in_be16(xspi->regs + XSPI_CR_OFFSET);
+                out_be16(xspi->regs + XSPI_CR_OFFSET,
+                         cr | XSPI_CR_TRANS_INHIBIT);
+
+                /* Read out all the data from the Rx FIFO */
+                sr = in_8(xspi->regs + XSPI_SR_OFFSET);
+                while ((sr & XSPI_SR_RX_EMPTY_MASK) == 0) {
+                        u8 data;
+
+                        data = in_8(xspi->regs + XSPI_RXD_OFFSET);
+                        if (xspi->rx_ptr) {
+                                *xspi->rx_ptr++ = data;
+                        }
+                        sr = in_8(xspi->regs + XSPI_SR_OFFSET);
+                }
+
+                /* See if there is more data to send */
+                if (xspi->remaining_bytes > 0) {
+                        xilinx_spi_fill_tx_fifo(xspi);
+                        /* Start the transfer by not inhibiting the
+                         * transmitter any longer
+                         */
+                        out_be16(xspi->regs + XSPI_CR_OFFSET, cr);
+                } else {
+                        /* No more data to send.
+                         * Indicate the transfer is completed.
+                         */
+                        complete(&xspi->done);
+                }
+        }
+
+        return IRQ_HANDLED;
+}
+
+static int __init xilinx_spi_probe(struct platform_device *dev)
+{
+        int ret = 0;
+        struct spi_master *master;
+        struct xilinx_spi *xspi;
+        struct xspi_platform_data *pdata;
+        struct resource *r;
+
+        /* Get resources(memory, IRQ) associated with the device */
+        master = spi_alloc_master(&dev->dev, sizeof(struct xilinx_spi));
+
+        if (master == NULL) {
+                return -ENOMEM;
+        }
+
+        platform_set_drvdata(dev, master);
+        pdata = dev->dev.platform_data;
+
+        if (pdata == NULL) {
+                ret = -ENODEV;
+                goto put_master;
+        }
+
+        r = platform_get_resource(dev, IORESOURCE_MEM, 0);
+        if (r == NULL) {
+                ret = -ENODEV;
+                goto put_master;
+        }
+
+        xspi = spi_master_get_devdata(master);
+        xspi->bitbang.master = spi_master_get(master);
+        xspi->bitbang.chipselect = xilinx_spi_chipselect;
+        xspi->bitbang.setup_transfer = xilinx_spi_setup_transfer;
+        xspi->bitbang.txrx_bufs = xilinx_spi_txrx_bufs;
+        xspi->bitbang.master->setup = xilinx_spi_setup;
+        init_completion(&xspi->done);
+
+        if (!request_mem_region(r->start,
+                        r->end - r->start + 1, XILINX_SPI_NAME)) {
+                ret = -ENXIO;
+                goto put_master;
+        }
+
+        xspi->regs = ioremap(r->start, r->end - r->start + 1);
+        if (xspi->regs == NULL) {
+                ret = -ENOMEM;
+                goto put_master;
+        }
+
+        xspi->irq = platform_get_irq(dev, 0);
+        if (xspi->irq < 0) {
+                ret = -ENXIO;
+                goto unmap_io;
+        }
+
+        master->bus_num = pdata->bus_num;
+        master->num_chipselect = pdata->num_chipselect;
+        xspi->speed_hz = pdata->speed_hz;
+
+        /* SPI controller initializations */
+        xspi_init_hw(xspi->regs);
+
+        /* Register for SPI Interrupt */
+        ret = request_irq(xspi->irq, xilinx_spi_irq, 0, XILINX_SPI_NAME, xspi);
+        if (ret != 0)
+                goto unmap_io;
+
+        ret = spi_bitbang_start(&xspi->bitbang);
+        if (ret != 0) {
+                dev_err(&dev->dev, "spi_bitbang_start FAILED\n");
+                goto free_irq;
+        }
+
+        dev_info(&dev->dev, "at 0x%08X mapped to 0x%08X, irq=%d\n",
+                        r->start, (u32)xspi->regs, xspi->irq);
+
+        return ret;
+
+free_irq:
+        free_irq(xspi->irq, xspi);
+unmap_io:
+        iounmap(xspi->regs);
+put_master:
+        spi_master_put(master);
+        return ret;
+}
+
+static int __devexit xilinx_spi_remove(struct platform_device *dev)
+{
+        struct xilinx_spi *xspi;
+        struct spi_master *master;
+
+        master = platform_get_drvdata(dev);
+        xspi = spi_master_get_devdata(master);
+
+        spi_bitbang_stop(&xspi->bitbang);
+        free_irq(xspi->irq, xspi);
+        iounmap(xspi->regs);
+        platform_set_drvdata(dev, 0);
+        spi_master_put(xspi->bitbang.master);
+
+        return 0;
+}
+
+static struct platform_driver xilinx_spi_driver = {
+        .probe  = xilinx_spi_probe,
+        .remove = __devexit_p(xilinx_spi_remove),
+        .driver = {
+                .name = XILINX_SPI_NAME,
+                .owner = THIS_MODULE,
+        },
+};
+
+static int __init xilinx_spi_init(void)
+{
+        return platform_driver_register(&xilinx_spi_driver);
+}
+module_init(xilinx_spi_init);
+
+static void __exit xilinx_spi_exit(void)
+{
+        platform_driver_unregister(&xilinx_spi_driver);
+}
+module_exit(xilinx_spi_exit);
+
+MODULE_AUTHOR("MontaVista Software, Inc. <source@mvista.com>");
+MODULE_DESCRIPTION("Xilinx SPI driver");
+MODULE_LICENSE("GPL");