3 files changed, 25 insertions, 44 deletions

diff --git a/drivers/serial/atmel_serial.c b/drivers/serial/atmel_serial.c
index 338b15c0a548..607d43a31048 100644
--- a/drivers/serial/atmel_serial.c
+++ b/drivers/serial/atmel_serial.c
@@ -1551,6 +1551,7 @@ static int __devinit atmel_serial_probe(struct platform_device *pdev)
         if (ret)
                 goto err_add_port;
 
+#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
         if (atmel_is_console_port(&port->uart)
                         && ATMEL_CONSOLE_DEVICE->flags & CON_ENABLED) {
                 /*
@@ -1559,6 +1560,7 @@ static int __devinit atmel_serial_probe(struct platform_device *pdev)
                  */
                 clk_disable(port->clk);
         }
+#endif
 
         device_init_wakeup(&pdev->dev, 1);
         platform_set_drvdata(pdev, port);
diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm2.c b/drivers/serial/cpm_uart/cpm_uart_cpm2.c
index 141c0a3333ad..a9802e76b5fa 100644
--- a/drivers/serial/cpm_uart/cpm_uart_cpm2.c
+++ b/drivers/serial/cpm_uart/cpm_uart_cpm2.c
@@ -132,7 +132,7 @@ int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con)
         memsz = L1_CACHE_ALIGN(pinfo->rx_nrfifos * pinfo->rx_fifosize) +
             L1_CACHE_ALIGN(pinfo->tx_nrfifos * pinfo->tx_fifosize);
         if (is_con) {
-                mem_addr = alloc_bootmem(memsz);
+                mem_addr = kzalloc(memsz, GFP_NOWAIT);
                 dma_addr = virt_to_bus(mem_addr);
         }
         else
diff --git a/drivers/serial/imx.c b/drivers/serial/imx.c
index 5d7b58f1fe42..7485afd0df4c 100644
--- a/drivers/serial/imx.c
+++ b/drivers/serial/imx.c
@@ -67,21 +67,8 @@
 #define UBIR  0xa4 /* BRM Incremental Register */
 #define UBMR  0xa8 /* BRM Modulator Register */
 #define UBRC  0xac /* Baud Rate Count Register */
-#if defined CONFIG_ARCH_MX3 || defined CONFIG_ARCH_MX2
-#define ONEMS 0xb0 /* One Millisecond register */
-#define UTS   0xb4 /* UART Test Register */
-#endif
-#ifdef CONFIG_ARCH_MX1
-#define BIPR1 0xb0 /* Incremental Preset Register 1 */
-#define BIPR2 0xb4 /* Incremental Preset Register 2 */
-#define BIPR3 0xb8 /* Incremental Preset Register 3 */
-#define BIPR4 0xbc /* Incremental Preset Register 4 */
-#define BMPR1 0xc0 /* BRM Modulator Register 1 */
-#define BMPR2 0xc4 /* BRM Modulator Register 2 */
-#define BMPR3 0xc8 /* BRM Modulator Register 3 */
-#define BMPR4 0xcc /* BRM Modulator Register 4 */
-#define UTS   0xd0 /* UART Test Register */
-#endif
+#define MX2_ONEMS 0xb0 /* One Millisecond register */
+#define UTS (cpu_is_mx1() ? 0xd0 : 0xb4) /* UART Test Register */
 
 /* UART Control Register Bit Fields.*/
 #define  URXD_CHARRDY    (1<<15)
@@ -101,12 +88,7 @@
 #define  UCR1_RTSDEN     (1<<5)  /* RTS delta interrupt enable */
 #define  UCR1_SNDBRK     (1<<4)  /* Send break */
 #define  UCR1_TDMAEN     (1<<3)  /* Transmitter ready DMA enable */
-#ifdef CONFIG_ARCH_MX1
-#define  UCR1_UARTCLKEN  (1<<2)  /* UART clock enabled */
-#endif
-#if defined CONFIG_ARCH_MX3 || defined CONFIG_ARCH_MX2
-#define  UCR1_UARTCLKEN  (0)     /* not present on mx2/mx3 */
-#endif
+#define  MX1_UCR1_UARTCLKEN  (1<<2)      /* UART clock enabled, mx1 only */
 #define  UCR1_DOZE       (1<<1)  /* Doze */
 #define  UCR1_UARTEN     (1<<0)  /* UART enabled */
 #define  UCR2_ESCI       (1<<15) /* Escape seq interrupt enable */
@@ -132,13 +114,9 @@
 #define  UCR3_RXDSEN     (1<<6)  /* Receive status interrupt enable */
 #define  UCR3_AIRINTEN   (1<<5)  /* Async IR wake interrupt enable */
 #define  UCR3_AWAKEN     (1<<4)  /* Async wake interrupt enable */
-#ifdef CONFIG_ARCH_MX1
-#define  UCR3_REF25      (1<<3)  /* Ref freq 25 MHz, only on mx1 */
-#define  UCR3_REF30      (1<<2)  /* Ref Freq 30 MHz, only on mx1 */
-#endif
-#if defined CONFIG_ARCH_MX2 || defined CONFIG_ARCH_MX3
-#define  UCR3_RXDMUXSEL  (1<<2)  /* RXD Muxed Input Select, on mx2/mx3 */
-#endif
+#define  MX1_UCR3_REF25          (1<<3)  /* Ref freq 25 MHz, only on mx1 */
+#define  MX1_UCR3_REF30          (1<<2)  /* Ref Freq 30 MHz, only on mx1 */
+#define  MX2_UCR3_RXDMUXSEL      (1<<2)  /* RXD Muxed Input Select, on mx2/mx3 */
 #define  UCR3_INVT       (1<<1)  /* Inverted Infrared transmission */
 #define  UCR3_BPEN       (1<<0)  /* Preset registers enable */
 #define  UCR4_CTSTL_32   (32<<10) /* CTS trigger level (32 chars) */
@@ -186,12 +164,10 @@
 #define  UTS_SOFTRST     (1<<0)  /* Software reset */
 
 /* We've been assigned a range on the "Low-density serial ports" major */
-#ifdef CONFIG_ARCH_MXC
 #define SERIAL_IMX_MAJOR        207
 #define MINOR_START             16
 #define DEV_NAME                "ttymxc"
 #define MAX_INTERNAL_IRQ        MXC_INTERNAL_IRQS
-#endif
 
 /*
  * This determines how often we check the modem status signals
@@ -706,11 +682,11 @@ static int imx_startup(struct uart_port *port)
                 }
         }
 
-#if defined CONFIG_ARCH_MX2 || defined CONFIG_ARCH_MX3
-        temp = readl(sport->port.membase + UCR3);
-        temp |= UCR3_RXDMUXSEL;
-        writel(temp, sport->port.membase + UCR3);
-#endif
+        if (!cpu_is_mx1()) {
+                temp = readl(sport->port.membase + UCR3);
+                temp |= MX2_UCR3_RXDMUXSEL;
+                writel(temp, sport->port.membase + UCR3);
+        }
 
         if (USE_IRDA(sport)) {
                 temp = readl(sport->port.membase + UCR4);
@@ -942,9 +918,9 @@ imx_set_termios(struct uart_port *port, struct ktermios *termios,
         writel(num, sport->port.membase + UBIR);
         writel(denom, sport->port.membase + UBMR);
 
-#ifdef ONEMS
-        writel(sport->port.uartclk / div / 1000, sport->port.membase + ONEMS);
-#endif
+        if (!cpu_is_mx1())
+                writel(sport->port.uartclk / div / 1000,
+                                sport->port.membase + MX2_ONEMS);
 
         writel(old_ucr1, sport->port.membase + UCR1);
 
@@ -1074,17 +1050,20 @@ static void
 imx_console_write(struct console *co, const char *s, unsigned int count)
 {
         struct imx_port *sport = imx_ports[co->index];
-        unsigned int old_ucr1, old_ucr2;
+        unsigned int old_ucr1, old_ucr2, ucr1;
 
         /*
          *      First, save UCR1/2 and then disable interrupts
          */
-        old_ucr1 = readl(sport->port.membase + UCR1);
+        ucr1 = old_ucr1 = readl(sport->port.membase + UCR1);
         old_ucr2 = readl(sport->port.membase + UCR2);
 
-        writel((old_ucr1 | UCR1_UARTCLKEN | UCR1_UARTEN) &
-                ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN),
-                sport->port.membase + UCR1);
+        if (cpu_is_mx1())
+                ucr1 |= MX1_UCR1_UARTCLKEN;
+        ucr1 |= UCR1_UARTEN;
+        ucr1 &= ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN);
+
+        writel(ucr1, sport->port.membase + UCR1);
 
         writel(old_ucr2 | UCR2_TXEN, sport->port.membase + UCR2);