aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/serial/mrst_max3110.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/serial/mrst_max3110.c')
-rw-r--r--drivers/serial/mrst_max3110.c844
1 files changed, 844 insertions, 0 deletions
diff --git a/drivers/serial/mrst_max3110.c b/drivers/serial/mrst_max3110.c
new file mode 100644
index 000000000000..f6ad1ecbff79
--- /dev/null
+++ b/drivers/serial/mrst_max3110.c
@@ -0,0 +1,844 @@
1/*
2 * max3110.c - spi uart protocol driver for Maxim 3110 on Moorestown
3 *
4 * Copyright (C) Intel 2008 Feng Tang <feng.tang@intel.com>
5 *
6 * This program is free software; you can redistribute it and/or modify it
7 * under the terms and conditions of the GNU General Public License,
8 * version 2, as published by the Free Software Foundation.
9 *
10 * This program is distributed in the hope it will be useful, but WITHOUT
11 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
12 * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
13 * more details.
14 *
15 * You should have received a copy of the GNU General Public License along with
16 * this program; if not, write to the Free Software Foundation, Inc.,
17 * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
18 */
19
20/*
21 * Note:
22 * 1. From Max3110 spec, the Rx FIFO has 8 words, while the Tx FIFO only has
23 * 1 word. If SPI master controller doesn't support sclk frequency change,
24 * then the char need be sent out one by one with some delay
25 *
26 * 2. Currently only RX availabe interrrupt is used, no need for waiting TXE
27 * interrupt for a low speed UART device
28 */
29
30#include <linux/module.h>
31#include <linux/ioport.h>
32#include <linux/init.h>
33#include <linux/console.h>
34#include <linux/sysrq.h>
35#include <linux/platform_device.h>
36#include <linux/tty.h>
37#include <linux/tty_flip.h>
38#include <linux/serial_core.h>
39#include <linux/serial_reg.h>
40
41#include <linux/kthread.h>
42#include <linux/delay.h>
43#include <asm/atomic.h>
44#include <linux/spi/spi.h>
45#include <linux/spi/dw_spi.h>
46
47#include "mrst_max3110.h"
48
49#define PR_FMT "mrst_max3110: "
50
51#define UART_TX_NEEDED 1
52#define CON_TX_NEEDED 2
53#define BIT_IRQ_PENDING 3
54
55struct uart_max3110 {
56 struct uart_port port;
57 struct spi_device *spi;
58 char *name;
59
60 wait_queue_head_t wq;
61 struct task_struct *main_thread;
62 struct task_struct *read_thread;
63 struct mutex thread_mutex;;
64
65 u32 baud;
66 u16 cur_conf;
67 u8 clock;
68 u8 parity, word_7bits;
69
70 unsigned long uart_flags;
71
72 /* console related */
73 struct circ_buf con_xmit;
74
75 /* irq related */
76 u16 irq;
77};
78
79/* global data structure, may need be removed */
80struct uart_max3110 *pmax;
81static inline void receive_char(struct uart_max3110 *max, u8 ch);
82static void receive_chars(struct uart_max3110 *max,
83 unsigned char *str, int len);
84static int max3110_read_multi(struct uart_max3110 *max, int len, u8 *buf);
85static void max3110_console_receive(struct uart_max3110 *max);
86
87int max3110_write_then_read(struct uart_max3110 *max,
88 const u8 *txbuf, u8 *rxbuf, unsigned len, int always_fast)
89{
90 struct spi_device *spi = max->spi;
91 struct spi_message message;
92 struct spi_transfer x;
93 int ret;
94
95 if (!txbuf || !rxbuf)
96 return -EINVAL;
97
98 spi_message_init(&message);
99 memset(&x, 0, sizeof x);
100 x.len = len;
101 x.tx_buf = txbuf;
102 x.rx_buf = rxbuf;
103 spi_message_add_tail(&x, &message);
104
105 if (always_fast)
106 x.speed_hz = 3125000;
107 else if (max->baud)
108 x.speed_hz = max->baud;
109
110 /* Do the i/o */
111 ret = spi_sync(spi, &message);
112 return ret;
113}
114
115/* Write a u16 to the device, and return one u16 read back */
116int max3110_out(struct uart_max3110 *max, const u16 out)
117{
118 u16 tmp;
119 int ret;
120
121 ret = max3110_write_then_read(max, (u8 *)&out, (u8 *)&tmp, 2, 1);
122 if (ret)
123 return ret;
124
125 /* If some valid data is read back */
126 if (tmp & MAX3110_READ_DATA_AVAILABLE)
127 receive_char(max, (tmp & 0xff));
128
129 return ret;
130}
131
132#define MAX_READ_LEN 20
133/*
134 * This is usually used to read data from SPIC RX FIFO, which doesn't
135 * need any delay like flushing character out. It returns how many
136 * valide bytes are read back
137 */
138static int max3110_read_multi(struct uart_max3110 *max, int len, u8 *buf)
139{
140 u16 out[MAX_READ_LEN], in[MAX_READ_LEN];
141 u8 *pbuf, valid_str[MAX_READ_LEN];
142 int i, j, bytelen;
143
144 if (len > MAX_READ_LEN) {
145 pr_err(PR_FMT "read len %d is too large\n", len);
146 return 0;
147 }
148
149 bytelen = len * 2;
150 memset(out, 0, bytelen);
151 memset(in, 0, bytelen);
152
153 if (max3110_write_then_read(max, (u8 *)out, (u8 *)in, bytelen, 1))
154 return 0;
155
156 /* If caller don't provide a buffer, then handle received char */
157 pbuf = buf ? buf : valid_str;
158
159 for (i = 0, j = 0; i < len; i++) {
160 if (in[i] & MAX3110_READ_DATA_AVAILABLE)
161 pbuf[j++] = (u8)(in[i] & 0xff);
162 }
163
164 if (j && (pbuf == valid_str))
165 receive_chars(max, valid_str, j);
166
167 return j;
168}
169
170static void serial_m3110_con_putchar(struct uart_port *port, int ch)
171{
172 struct uart_max3110 *max =
173 container_of(port, struct uart_max3110, port);
174 struct circ_buf *xmit = &max->con_xmit;
175
176 if (uart_circ_chars_free(xmit)) {
177 xmit->buf[xmit->head] = (char)ch;
178 xmit->head = (xmit->head + 1) & (PAGE_SIZE - 1);
179 }
180
181
182 if (!test_and_set_bit(CON_TX_NEEDED, &max->uart_flags))
183 wake_up_process(max->main_thread);
184}
185
186/*
187 * Print a string to the serial port trying not to disturb
188 * any possible real use of the port...
189 *
190 * The console_lock must be held when we get here.
191 */
192static void serial_m3110_con_write(struct console *co,
193 const char *s, unsigned int count)
194{
195 if (!pmax)
196 return;
197
198 uart_console_write(&pmax->port, s, count, serial_m3110_con_putchar);
199}
200
201static int __init
202serial_m3110_con_setup(struct console *co, char *options)
203{
204 struct uart_max3110 *max = pmax;
205 int baud = 115200;
206 int bits = 8;
207 int parity = 'n';
208 int flow = 'n';
209
210 pr_info(PR_FMT "setting up console\n");
211
212 if (!max) {
213 pr_err(PR_FMT "pmax is NULL, return");
214 return -ENODEV;
215 }
216
217 if (options)
218 uart_parse_options(options, &baud, &parity, &bits, &flow);
219
220 return uart_set_options(&max->port, co, baud, parity, bits, flow);
221}
222
223static struct tty_driver *serial_m3110_con_device(struct console *co,
224 int *index)
225{
226 struct uart_driver *p = co->data;
227 *index = co->index;
228 return p->tty_driver;
229}
230
231static struct uart_driver serial_m3110_reg;
232static struct console serial_m3110_console = {
233 .name = "ttyS",
234 .write = serial_m3110_con_write,
235 .device = serial_m3110_con_device,
236 .setup = serial_m3110_con_setup,
237 .flags = CON_PRINTBUFFER,
238 .index = -1,
239 .data = &serial_m3110_reg,
240};
241
242#define MRST_CONSOLE (&serial_m3110_console)
243
244static unsigned int serial_m3110_tx_empty(struct uart_port *port)
245{
246 return 1;
247}
248
249static void serial_m3110_stop_tx(struct uart_port *port)
250{
251 return;
252}
253
254/* stop_rx will be called in spin_lock env */
255static void serial_m3110_stop_rx(struct uart_port *port)
256{
257 return;
258}
259
260#define WORDS_PER_XFER 128
261static inline void send_circ_buf(struct uart_max3110 *max,
262 struct circ_buf *xmit)
263{
264 int len, left = 0;
265 u16 obuf[WORDS_PER_XFER], ibuf[WORDS_PER_XFER];
266 u8 valid_str[WORDS_PER_XFER];
267 int i, j;
268
269 while (!uart_circ_empty(xmit)) {
270 left = uart_circ_chars_pending(xmit);
271 while (left) {
272 len = (left >= WORDS_PER_XFER) ? WORDS_PER_XFER : left;
273
274 memset(obuf, 0, len * 2);
275 memset(ibuf, 0, len * 2);
276 for (i = 0; i < len; i++) {
277 obuf[i] = (u8)xmit->buf[xmit->tail] | WD_TAG;
278 xmit->tail = (xmit->tail + 1) &
279 (UART_XMIT_SIZE - 1);
280 }
281 max3110_write_then_read(max, (u8 *)obuf,
282 (u8 *)ibuf, len * 2, 0);
283
284 for (i = 0, j = 0; i < len; i++) {
285 if (ibuf[i] & MAX3110_READ_DATA_AVAILABLE)
286 valid_str[j++] = (u8)(ibuf[i] & 0xff);
287 }
288
289 if (j)
290 receive_chars(max, valid_str, j);
291
292 max->port.icount.tx += len;
293 left -= len;
294 }
295 }
296}
297
298static void transmit_char(struct uart_max3110 *max)
299{
300 struct uart_port *port = &max->port;
301 struct circ_buf *xmit = &port->state->xmit;
302
303 if (uart_circ_empty(xmit) || uart_tx_stopped(port))
304 return;
305
306 send_circ_buf(max, xmit);
307
308 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
309 uart_write_wakeup(port);
310
311 if (uart_circ_empty(xmit))
312 serial_m3110_stop_tx(port);
313}
314
315/* This will be called by uart_write() and tty_write, can't
316 * go to sleep */
317static void serial_m3110_start_tx(struct uart_port *port)
318{
319 struct uart_max3110 *max =
320 container_of(port, struct uart_max3110, port);
321
322 if (!test_and_set_bit(UART_TX_NEEDED, &max->uart_flags))
323 wake_up_process(max->main_thread);
324}
325
326static void receive_chars(struct uart_max3110 *max, unsigned char *str, int len)
327{
328 struct uart_port *port = &max->port;
329 struct tty_struct *tty;
330 int usable;
331
332 /* If uart is not opened, just return */
333 if (!port->state)
334 return;
335
336 tty = port->state->port.tty;
337 if (!tty)
338 return; /* receive some char before the tty is opened */
339
340 while (len) {
341 usable = tty_buffer_request_room(tty, len);
342 if (usable) {
343 tty_insert_flip_string(tty, str, usable);
344 str += usable;
345 port->icount.rx += usable;
346 tty_flip_buffer_push(tty);
347 }
348 len -= usable;
349 }
350}
351
352static inline void receive_char(struct uart_max3110 *max, u8 ch)
353{
354 receive_chars(max, &ch, 1);
355}
356
357static void max3110_console_receive(struct uart_max3110 *max)
358{
359 int loop = 1, num, total = 0;
360 u8 recv_buf[512], *pbuf;
361
362 pbuf = recv_buf;
363 do {
364 num = max3110_read_multi(max, 8, pbuf);
365
366 if (num) {
367 loop = 10;
368 pbuf += num;
369 total += num;
370
371 if (total >= 500) {
372 receive_chars(max, recv_buf, total);
373 pbuf = recv_buf;
374 total = 0;
375 }
376 }
377 } while (--loop);
378
379 if (total)
380 receive_chars(max, recv_buf, total);
381}
382
383static int max3110_main_thread(void *_max)
384{
385 struct uart_max3110 *max = _max;
386 wait_queue_head_t *wq = &max->wq;
387 int ret = 0;
388 struct circ_buf *xmit = &max->con_xmit;
389
390 init_waitqueue_head(wq);
391 pr_info(PR_FMT "start main thread\n");
392
393 do {
394 wait_event_interruptible(*wq, max->uart_flags || kthread_should_stop());
395
396 mutex_lock(&max->thread_mutex);
397
398 if (test_and_clear_bit(BIT_IRQ_PENDING, &max->uart_flags))
399 max3110_console_receive(max);
400
401 /* first handle console output */
402 if (test_and_clear_bit(CON_TX_NEEDED, &max->uart_flags))
403 send_circ_buf(max, xmit);
404
405 /* handle uart output */
406 if (test_and_clear_bit(UART_TX_NEEDED, &max->uart_flags))
407 transmit_char(max);
408
409 mutex_unlock(&max->thread_mutex);
410
411 } while (!kthread_should_stop());
412
413 return ret;
414}
415
416#ifdef CONFIG_MRST_MAX3110_IRQ
417static irqreturn_t serial_m3110_irq(int irq, void *dev_id)
418{
419 struct uart_max3110 *max = dev_id;
420
421 /* max3110's irq is a falling edge, not level triggered,
422 * so no need to disable the irq */
423 if (!test_and_set_bit(BIT_IRQ_PENDING, &max->uart_flags))
424 wake_up_process(max->main_thread);
425
426 return IRQ_HANDLED;
427}
428#else
429/* if don't use RX IRQ, then need a thread to polling read */
430static int max3110_read_thread(void *_max)
431{
432 struct uart_max3110 *max = _max;
433
434 pr_info(PR_FMT "start read thread\n");
435 do {
436 mutex_lock(&max->thread_mutex);
437 max3110_console_receive(max);
438 mutex_unlock(&max->thread_mutex);
439
440 set_current_state(TASK_INTERRUPTIBLE);
441 schedule_timeout(HZ / 20);
442 } while (!kthread_should_stop());
443
444 return 0;
445}
446#endif
447
448static int serial_m3110_startup(struct uart_port *port)
449{
450 struct uart_max3110 *max =
451 container_of(port, struct uart_max3110, port);
452 u16 config = 0;
453 int ret = 0;
454
455 if (port->line != 0)
456 pr_err(PR_FMT "uart port startup failed\n");
457
458 /* firstly disable all IRQ and config it to 115200, 8n1 */
459 config = WC_TAG | WC_FIFO_ENABLE
460 | WC_1_STOPBITS
461 | WC_8BIT_WORD
462 | WC_BAUD_DR2;
463 ret = max3110_out(max, config);
464
465 /* as we use thread to handle tx/rx, need set low latency */
466 port->state->port.tty->low_latency = 1;
467
468#ifdef CONFIG_MRST_MAX3110_IRQ
469 ret = request_irq(max->irq, serial_m3110_irq,
470 IRQ_TYPE_EDGE_FALLING, "max3110", max);
471 if (ret)
472 return ret;
473
474 /* enable RX IRQ only */
475 config |= WC_RXA_IRQ_ENABLE;
476 max3110_out(max, config);
477#else
478 /* if IRQ is disabled, start a read thread for input data */
479 max->read_thread =
480 kthread_run(max3110_read_thread, max, "max3110_read");
481#endif
482
483 max->cur_conf = config;
484 return 0;
485}
486
487static void serial_m3110_shutdown(struct uart_port *port)
488{
489 struct uart_max3110 *max =
490 container_of(port, struct uart_max3110, port);
491 u16 config;
492
493 if (max->read_thread) {
494 kthread_stop(max->read_thread);
495 max->read_thread = NULL;
496 }
497
498#ifdef CONFIG_MRST_MAX3110_IRQ
499 free_irq(max->irq, max);
500#endif
501
502 /* Disable interrupts from this port */
503 config = WC_TAG | WC_SW_SHDI;
504 max3110_out(max, config);
505}
506
507static void serial_m3110_release_port(struct uart_port *port)
508{
509}
510
511static int serial_m3110_request_port(struct uart_port *port)
512{
513 return 0;
514}
515
516static void serial_m3110_config_port(struct uart_port *port, int flags)
517{
518 /* give it fake type */
519 port->type = PORT_PXA;
520}
521
522static int
523serial_m3110_verify_port(struct uart_port *port, struct serial_struct *ser)
524{
525 /* we don't want the core code to modify any port params */
526 return -EINVAL;
527}
528
529
530static const char *serial_m3110_type(struct uart_port *port)
531{
532 struct uart_max3110 *max =
533 container_of(port, struct uart_max3110, port);
534 return max->name;
535}
536
537static void
538serial_m3110_set_termios(struct uart_port *port, struct ktermios *termios,
539 struct ktermios *old)
540{
541 struct uart_max3110 *max =
542 container_of(port, struct uart_max3110, port);
543 unsigned char cval;
544 unsigned int baud, parity = 0;
545 int clk_div = -1;
546 u16 new_conf = max->cur_conf;
547
548 switch (termios->c_cflag & CSIZE) {
549 case CS7:
550 cval = UART_LCR_WLEN7;
551 new_conf |= WC_7BIT_WORD;
552 break;
553 default:
554 case CS8:
555 cval = UART_LCR_WLEN8;
556 new_conf |= WC_8BIT_WORD;
557 break;
558 }
559
560 baud = uart_get_baud_rate(port, termios, old, 0, 230400);
561
562 /* first calc the div for 1.8MHZ clock case */
563 switch (baud) {
564 case 300:
565 clk_div = WC_BAUD_DR384;
566 break;
567 case 600:
568 clk_div = WC_BAUD_DR192;
569 break;
570 case 1200:
571 clk_div = WC_BAUD_DR96;
572 break;
573 case 2400:
574 clk_div = WC_BAUD_DR48;
575 break;
576 case 4800:
577 clk_div = WC_BAUD_DR24;
578 break;
579 case 9600:
580 clk_div = WC_BAUD_DR12;
581 break;
582 case 19200:
583 clk_div = WC_BAUD_DR6;
584 break;
585 case 38400:
586 clk_div = WC_BAUD_DR3;
587 break;
588 case 57600:
589 clk_div = WC_BAUD_DR2;
590 break;
591 case 115200:
592 clk_div = WC_BAUD_DR1;
593 break;
594 case 230400:
595 if (max->clock & MAX3110_HIGH_CLK)
596 break;
597 default:
598 /* pick the previous baud rate */
599 baud = max->baud;
600 clk_div = max->cur_conf & WC_BAUD_DIV_MASK;
601 tty_termios_encode_baud_rate(termios, baud, baud);
602 }
603
604 if (max->clock & MAX3110_HIGH_CLK) {
605 clk_div += 1;
606 /* high clk version max3110 doesn't support B300 */
607 if (baud == 300)
608 baud = 600;
609 if (baud == 230400)
610 clk_div = WC_BAUD_DR1;
611 tty_termios_encode_baud_rate(termios, baud, baud);
612 }
613
614 new_conf = (new_conf & ~WC_BAUD_DIV_MASK) | clk_div;
615 if (termios->c_cflag & CSTOPB)
616 new_conf |= WC_2_STOPBITS;
617 else
618 new_conf &= ~WC_2_STOPBITS;
619
620 if (termios->c_cflag & PARENB) {
621 new_conf |= WC_PARITY_ENABLE;
622 parity |= UART_LCR_PARITY;
623 } else
624 new_conf &= ~WC_PARITY_ENABLE;
625
626 if (!(termios->c_cflag & PARODD))
627 parity |= UART_LCR_EPAR;
628 max->parity = parity;
629
630 uart_update_timeout(port, termios->c_cflag, baud);
631
632 new_conf |= WC_TAG;
633 if (new_conf != max->cur_conf) {
634 max3110_out(max, new_conf);
635 max->cur_conf = new_conf;
636 max->baud = baud;
637 }
638}
639
640/* don't handle hw handshaking */
641static unsigned int serial_m3110_get_mctrl(struct uart_port *port)
642{
643 return TIOCM_DSR | TIOCM_CAR | TIOCM_DSR;
644}
645
646static void serial_m3110_set_mctrl(struct uart_port *port, unsigned int mctrl)
647{
648}
649
650static void serial_m3110_break_ctl(struct uart_port *port, int break_state)
651{
652}
653
654static void serial_m3110_pm(struct uart_port *port, unsigned int state,
655 unsigned int oldstate)
656{
657}
658
659static void serial_m3110_enable_ms(struct uart_port *port)
660{
661}
662
663struct uart_ops serial_m3110_ops = {
664 .tx_empty = serial_m3110_tx_empty,
665 .set_mctrl = serial_m3110_set_mctrl,
666 .get_mctrl = serial_m3110_get_mctrl,
667 .stop_tx = serial_m3110_stop_tx,
668 .start_tx = serial_m3110_start_tx,
669 .stop_rx = serial_m3110_stop_rx,
670 .enable_ms = serial_m3110_enable_ms,
671 .break_ctl = serial_m3110_break_ctl,
672 .startup = serial_m3110_startup,
673 .shutdown = serial_m3110_shutdown,
674 .set_termios = serial_m3110_set_termios, /* must have */
675 .pm = serial_m3110_pm,
676 .type = serial_m3110_type,
677 .release_port = serial_m3110_release_port,
678 .request_port = serial_m3110_request_port,
679 .config_port = serial_m3110_config_port,
680 .verify_port = serial_m3110_verify_port,
681};
682
683static struct uart_driver serial_m3110_reg = {
684 .owner = THIS_MODULE,
685 .driver_name = "MRST serial",
686 .dev_name = "ttyS",
687 .major = TTY_MAJOR,
688 .minor = 64,
689 .nr = 1,
690 .cons = MRST_CONSOLE,
691};
692
693static int serial_m3110_suspend(struct spi_device *spi, pm_message_t state)
694{
695 return 0;
696}
697
698static int serial_m3110_resume(struct spi_device *spi)
699{
700 return 0;
701}
702
703static struct dw_spi_chip spi0_uart = {
704 .poll_mode = 1,
705 .enable_dma = 0,
706 .type = SPI_FRF_SPI,
707};
708
709static int serial_m3110_probe(struct spi_device *spi)
710{
711 struct uart_max3110 *max;
712 int ret;
713 unsigned char *buffer;
714 u16 res;
715 max = kzalloc(sizeof(*max), GFP_KERNEL);
716 if (!max)
717 return -ENOMEM;
718
719 /* set spi info */
720 spi->mode = SPI_MODE_0;
721 spi->bits_per_word = 16;
722 max->clock = MAX3110_HIGH_CLK;
723 spi->controller_data = &spi0_uart;
724
725 spi_setup(spi);
726
727 max->port.type = PORT_PXA; /* need apply for a max3110 type */
728 max->port.fifosize = 2; /* only have 16b buffer */
729 max->port.ops = &serial_m3110_ops;
730 max->port.line = 0;
731 max->port.dev = &spi->dev;
732 max->port.uartclk = 115200;
733
734 max->spi = spi;
735 max->name = spi->modalias; /* use spi name as the name */
736 max->irq = (u16)spi->irq;
737
738 mutex_init(&max->thread_mutex);
739
740 max->word_7bits = 0;
741 max->parity = 0;
742 max->baud = 0;
743
744 max->cur_conf = 0;
745 max->uart_flags = 0;
746
747 /* Check if reading configuration register returns something sane */
748
749 res = RC_TAG;
750 ret = max3110_write_then_read(max, (u8 *)&res, (u8 *)&res, 2, 0);
751 if (ret < 0 || res == 0 || res == 0xffff) {
752 printk(KERN_ERR "MAX3111 deemed not present (conf reg %04x)",
753 res);
754 ret = -ENODEV;
755 goto err_get_page;
756 }
757 buffer = (unsigned char *)__get_free_page(GFP_KERNEL);
758 if (!buffer) {
759 ret = -ENOMEM;
760 goto err_get_page;
761 }
762 max->con_xmit.buf = (unsigned char *)buffer;
763 max->con_xmit.head = max->con_xmit.tail = 0;
764
765 max->main_thread = kthread_run(max3110_main_thread,
766 max, "max3110_main");
767 if (IS_ERR(max->main_thread)) {
768 ret = PTR_ERR(max->main_thread);
769 goto err_kthread;
770 }
771
772 pmax = max;
773 /* give membase a psudo value to pass serial_core's check */
774 max->port.membase = (void *)0xff110000;
775 uart_add_one_port(&serial_m3110_reg, &max->port);
776
777 return 0;
778
779err_kthread:
780 free_page((unsigned long)buffer);
781err_get_page:
782 pmax = NULL;
783 kfree(max);
784 return ret;
785}
786
787static int max3110_remove(struct spi_device *dev)
788{
789 struct uart_max3110 *max = pmax;
790
791 if (!pmax)
792 return 0;
793
794 pmax = NULL;
795 uart_remove_one_port(&serial_m3110_reg, &max->port);
796
797 free_page((unsigned long)max->con_xmit.buf);
798
799 if (max->main_thread)
800 kthread_stop(max->main_thread);
801
802 kfree(max);
803 return 0;
804}
805
806static struct spi_driver uart_max3110_driver = {
807 .driver = {
808 .name = "spi_max3111",
809 .bus = &spi_bus_type,
810 .owner = THIS_MODULE,
811 },
812 .probe = serial_m3110_probe,
813 .remove = __devexit_p(max3110_remove),
814 .suspend = serial_m3110_suspend,
815 .resume = serial_m3110_resume,
816};
817
818
819int __init serial_m3110_init(void)
820{
821 int ret = 0;
822
823 ret = uart_register_driver(&serial_m3110_reg);
824 if (ret)
825 return ret;
826
827 ret = spi_register_driver(&uart_max3110_driver);
828 if (ret)
829 uart_unregister_driver(&serial_m3110_reg);
830
831 return ret;
832}
833
834void __exit serial_m3110_exit(void)
835{
836 spi_unregister_driver(&uart_max3110_driver);
837 uart_unregister_driver(&serial_m3110_reg);
838}
839
840module_init(serial_m3110_init);
841module_exit(serial_m3110_exit);
842
843MODULE_LICENSE("GPL");
844MODULE_ALIAS("max3110-uart");
generated by cgit v1.2.2 (git 2.25.0) at 2025-03-08 22:25:04 -0500