1 files changed, 9 insertions, 85 deletions

diff --git a/drivers/scsi/qla2xxx/qla_init.c b/drivers/scsi/qla2xxx/qla_init.c
index 08cb5e3fb553..a823f0bc519d 100644
--- a/drivers/scsi/qla2xxx/qla_init.c
+++ b/drivers/scsi/qla2xxx/qla_init.c
@@ -59,9 +59,6 @@ int
 qla2x00_initialize_adapter(scsi_qla_host_t *ha)
 {
         int     rval;
-        uint8_t restart_risc = 0;
-        uint8_t retry;
-        uint32_t wait_time;
 
         /* Clear adapter flags. */
         ha->flags.online = 0;
@@ -104,87 +101,15 @@ qla2x00_initialize_adapter(scsi_qla_host_t *ha)
 
         qla_printk(KERN_INFO, ha, "Verifying loaded RISC code...\n");
 
-        retry = 10;
-        /*
-         * Try to configure the loop.
-         */
-        do {
-                restart_risc = 0;
-
-                /* If firmware needs to be loaded */
-                if (qla2x00_isp_firmware(ha) != QLA_SUCCESS) {
-                        if ((rval = ha->isp_ops.chip_diag(ha)) == QLA_SUCCESS) {
-                                rval = qla2x00_setup_chip(ha);
-                        }
-                }
-
-                if (rval == QLA_SUCCESS &&
-                    (rval = qla2x00_init_rings(ha)) == QLA_SUCCESS) {
-check_fw_ready_again:
-                        /*
-                         * Wait for a successful LIP up to a maximum
-                         * of (in seconds): RISC login timeout value,
-                         * RISC retry count value, and port down retry
-                         * value OR a minimum of 4 seconds OR If no
-                         * cable, only 5 seconds.
-                         */
-                        rval = qla2x00_fw_ready(ha);
-                        if (rval == QLA_SUCCESS) {
-                                clear_bit(RESET_MARKER_NEEDED, &ha->dpc_flags);
-
-                                /* Issue a marker after FW becomes ready. */
-                                qla2x00_marker(ha, 0, 0, MK_SYNC_ALL);
-
-                                /*
-                                 * Wait at most MAX_TARGET RSCNs for a stable
-                                 * link.
-                                 */
-                                wait_time = 256;
-                                do {
-                                        clear_bit(LOOP_RESYNC_NEEDED,
-                                            &ha->dpc_flags);
-                                        rval = qla2x00_configure_loop(ha);
-
-                                        if (test_and_clear_bit(ISP_ABORT_NEEDED,
-                                            &ha->dpc_flags)) {
-                                                restart_risc = 1;
-                                                break;
-                                        }
-
-                                        /*
-                                         * If loop state change while we were
-                                         * discoverying devices then wait for
-                                         * LIP to complete
-                                         */
-
-                                        if (atomic_read(&ha->loop_state) !=
-                                            LOOP_READY && retry--) {
-                                                goto check_fw_ready_again;
-                                        }
-                                        wait_time--;
-                                } while (!atomic_read(&ha->loop_down_timer) &&
-                                    retry &&
-                                    wait_time &&
-                                    (test_bit(LOOP_RESYNC_NEEDED,
-                                        &ha->dpc_flags)));
-
-                                if (wait_time == 0)
-                                        rval = QLA_FUNCTION_FAILED;
-                        } else if (ha->device_flags & DFLG_NO_CABLE)
-                                /* If no cable, then all is good. */
-                                rval = QLA_SUCCESS;
-                }
-        } while (restart_risc && retry--);
-
-        if (rval == QLA_SUCCESS) {
-                clear_bit(RESET_MARKER_NEEDED, &ha->dpc_flags);
-                qla2x00_marker(ha, 0, 0, MK_SYNC_ALL);
-                ha->marker_needed = 0;
-
-                ha->flags.online = 1;
-        } else {
-                DEBUG2_3(printk("%s(): **** FAILED ****\n", __func__));
+        if (qla2x00_isp_firmware(ha) != QLA_SUCCESS) {
+                rval = ha->isp_ops.chip_diag(ha);
+                if (rval)
+                        return (rval);
+                rval = qla2x00_setup_chip(ha);
+                if (rval)
+                        return (rval);
         }
+        rval = qla2x00_init_rings(ha);
 
         return (rval);
 }
@@ -2208,8 +2133,7 @@ qla2x00_update_fcport(scsi_qla_host_t *ha, fc_port_t *fcport)
 
         atomic_set(&fcport->state, FCS_ONLINE);
 
-        if (ha->flags.init_done)
-                qla2x00_reg_remote_port(ha, fcport);
+        qla2x00_reg_remote_port(ha, fcport);
 }
 
 void