1 files changed, 270 insertions, 88 deletions

diff --git a/drivers/scsi/lpfc/lpfc.h b/drivers/scsi/lpfc/lpfc.h
index 82e8f90c4617..f8f64d6485cd 100644
--- a/drivers/scsi/lpfc/lpfc.h
+++ b/drivers/scsi/lpfc/lpfc.h
@@ -19,8 +19,9 @@
  * included with this package.                                     *
  *******************************************************************/
 
-struct lpfc_sli2_slim;
+#include <scsi/scsi_host.h>
 
+struct lpfc_sli2_slim;
 
 #define LPFC_MAX_TARGET         256     /* max number of targets supported */
 #define LPFC_MAX_DISC_THREADS   64      /* max outstanding discovery els
@@ -32,6 +33,20 @@ struct lpfc_sli2_slim;
 #define LPFC_IOCB_LIST_CNT      2250    /* list of IOCBs for fast-path usage. */
 #define LPFC_Q_RAMP_UP_INTERVAL 120     /* lun q_depth ramp up interval */
 
+/*
+ * Following time intervals are used of adjusting SCSI device
+ * queue depths when there are driver resource error or Firmware
+ * resource error.
+ */
+#define QUEUE_RAMP_DOWN_INTERVAL        (1 * HZ)   /* 1 Second */
+#define QUEUE_RAMP_UP_INTERVAL          (300 * HZ) /* 5 minutes */
+
+/* Number of exchanges reserved for discovery to complete */
+#define LPFC_DISC_IOCB_BUFF_COUNT 20
+
+#define LPFC_HB_MBOX_INTERVAL   5       /* Heart beat interval in seconds. */
+#define LPFC_HB_MBOX_TIMEOUT    30      /* Heart beat timeout  in seconds. */
+
 /* Define macros for 64 bit support */
 #define putPaddrLow(addr)    ((uint32_t) (0xffffffff & (u64)(addr)))
 #define putPaddrHigh(addr)   ((uint32_t) (0xffffffff & (((u64)(addr))>>32)))
@@ -61,6 +76,11 @@ struct lpfc_dma_pool {
         uint32_t    current_count;
 };
 
+struct hbq_dmabuf {
+        struct lpfc_dmabuf dbuf;
+        uint32_t tag;
+};
+
 /* Priority bit.  Set value to exceed low water mark in lpfc_mem. */
 #define MEM_PRI         0x100
 
@@ -90,6 +110,29 @@ typedef struct lpfc_vpd {
                 uint32_t sli2FwRev;
                 uint8_t sli2FwName[16];
         } rev;
+        struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+                uint32_t rsvd2  :24;  /* Reserved                             */
+                uint32_t cmv    : 1;  /* Configure Max VPIs                   */
+                uint32_t ccrp   : 1;  /* Config Command Ring Polling          */
+                uint32_t csah   : 1;  /* Configure Synchronous Abort Handling */
+                uint32_t chbs   : 1;  /* Cofigure Host Backing store          */
+                uint32_t cinb   : 1;  /* Enable Interrupt Notification Block  */
+                uint32_t cerbm  : 1;  /* Configure Enhanced Receive Buf Mgmt  */
+                uint32_t cmx    : 1;  /* Configure Max XRIs                   */
+                uint32_t cmr    : 1;  /* Configure Max RPIs                   */
+#else   /*  __LITTLE_ENDIAN */
+                uint32_t cmr    : 1;  /* Configure Max RPIs                   */
+                uint32_t cmx    : 1;  /* Configure Max XRIs                   */
+                uint32_t cerbm  : 1;  /* Configure Enhanced Receive Buf Mgmt  */
+                uint32_t cinb   : 1;  /* Enable Interrupt Notification Block  */
+                uint32_t chbs   : 1;  /* Cofigure Host Backing store          */
+                uint32_t csah   : 1;  /* Configure Synchronous Abort Handling */
+                uint32_t ccrp   : 1;  /* Config Command Ring Polling          */
+                uint32_t cmv    : 1;  /* Configure Max VPIs                   */
+                uint32_t rsvd2  :24;  /* Reserved                             */
+#endif
+        } sli3Feat;
 } lpfc_vpd_t;
 
 struct lpfc_scsi_buf;
@@ -122,6 +165,7 @@ struct lpfc_stats {
         uint32_t elsRcvRPS;
         uint32_t elsRcvRPL;
         uint32_t elsXmitFLOGI;
+        uint32_t elsXmitFDISC;
         uint32_t elsXmitPLOGI;
         uint32_t elsXmitPRLI;
         uint32_t elsXmitADISC;
@@ -165,50 +209,186 @@ struct lpfc_sysfs_mbox {
         struct lpfcMboxq *    mbox;
 };
 
+struct lpfc_hba;
+
+
+enum discovery_state {
+        LPFC_VPORT_UNKNOWN     =  0,    /* vport state is unknown */
+        LPFC_VPORT_FAILED      =  1,    /* vport has failed */
+        LPFC_LOCAL_CFG_LINK    =  6,    /* local NPORT Id configured */
+        LPFC_FLOGI             =  7,    /* FLOGI sent to Fabric */
+        LPFC_FDISC             =  8,    /* FDISC sent for vport */
+        LPFC_FABRIC_CFG_LINK   =  9,    /* Fabric assigned NPORT Id
+                                         * configured */
+        LPFC_NS_REG            =  10,   /* Register with NameServer */
+        LPFC_NS_QRY            =  11,   /* Query NameServer for NPort ID list */
+        LPFC_BUILD_DISC_LIST   =  12,   /* Build ADISC and PLOGI lists for
+                                         * device authentication / discovery */
+        LPFC_DISC_AUTH         =  13,   /* Processing ADISC list */
+        LPFC_VPORT_READY       =  32,
+};
+
+enum hba_state {
+        LPFC_LINK_UNKNOWN    =   0,   /* HBA state is unknown */
+        LPFC_WARM_START      =   1,   /* HBA state after selective reset */
+        LPFC_INIT_START      =   2,   /* Initial state after board reset */
+        LPFC_INIT_MBX_CMDS   =   3,   /* Initialize HBA with mbox commands */
+        LPFC_LINK_DOWN       =   4,   /* HBA initialized, link is down */
+        LPFC_LINK_UP         =   5,   /* Link is up  - issue READ_LA */
+        LPFC_CLEAR_LA        =   6,   /* authentication cmplt - issue
+                                       * CLEAR_LA */
+        LPFC_HBA_READY       =  32,
+        LPFC_HBA_ERROR       =  -1
+};
+
+struct lpfc_vport {
+        struct list_head listentry;
+        struct lpfc_hba *phba;
+        uint8_t port_type;
+#define LPFC_PHYSICAL_PORT 1
+#define LPFC_NPIV_PORT  2
+#define LPFC_FABRIC_PORT 3
+        enum discovery_state port_state;
+
+        uint16_t vpi;
+
+        uint32_t fc_flag;       /* FC flags */
+/* Several of these flags are HBA centric and should be moved to
+ * phba->link_flag (e.g. FC_PTP, FC_PUBLIC_LOOP)
+ */
+#define FC_PT2PT                0x1      /* pt2pt with no fabric */
+#define FC_PT2PT_PLOGI          0x2      /* pt2pt initiate PLOGI */
+#define FC_DISC_TMO             0x4      /* Discovery timer running */
+#define FC_PUBLIC_LOOP          0x8      /* Public loop */
+#define FC_LBIT                 0x10     /* LOGIN bit in loopinit set */
+#define FC_RSCN_MODE            0x20     /* RSCN cmd rcv'ed */
+#define FC_NLP_MORE             0x40     /* More node to process in node tbl */
+#define FC_OFFLINE_MODE         0x80     /* Interface is offline for diag */
+#define FC_FABRIC               0x100    /* We are fabric attached */
+#define FC_ESTABLISH_LINK       0x200    /* Reestablish Link */
+#define FC_RSCN_DISCOVERY       0x400    /* Auth all devices after RSCN */
+#define FC_SCSI_SCAN_TMO        0x4000   /* scsi scan timer running */
+#define FC_ABORT_DISCOVERY      0x8000   /* we want to abort discovery */
+#define FC_NDISC_ACTIVE         0x10000  /* NPort discovery active */
+#define FC_BYPASSED_MODE        0x20000  /* NPort is in bypassed mode */
+#define FC_RFF_NOT_SUPPORTED    0x40000  /* RFF_ID was rejected by switch */
+#define FC_VPORT_NEEDS_REG_VPI  0x80000  /* Needs to have its vpi registered */
+#define FC_RSCN_DEFERRED        0x100000 /* A deferred RSCN being processed */
+
+        struct list_head fc_nodes;
+
+        /* Keep counters for the number of entries in each list. */
+        uint16_t fc_plogi_cnt;
+        uint16_t fc_adisc_cnt;
+        uint16_t fc_reglogin_cnt;
+        uint16_t fc_prli_cnt;
+        uint16_t fc_unmap_cnt;
+        uint16_t fc_map_cnt;
+        uint16_t fc_npr_cnt;
+        uint16_t fc_unused_cnt;
+        struct serv_parm fc_sparam;     /* buffer for our service parameters */
+
+        uint32_t fc_myDID;      /* fibre channel S_ID */
+        uint32_t fc_prevDID;    /* previous fibre channel S_ID */
+
+        int32_t stopped;   /* HBA has not been restarted since last ERATT */
+        uint8_t fc_linkspeed;   /* Link speed after last READ_LA */
+
+        uint32_t num_disc_nodes;        /*in addition to hba_state */
+
+        uint32_t fc_nlp_cnt;    /* outstanding NODELIST requests */
+        uint32_t fc_rscn_id_cnt;        /* count of RSCNs payloads in list */
+        struct lpfc_dmabuf *fc_rscn_id_list[FC_MAX_HOLD_RSCN];
+        struct lpfc_name fc_nodename;   /* fc nodename */
+        struct lpfc_name fc_portname;   /* fc portname */
+
+        struct lpfc_work_evt disc_timeout_evt;
+
+        struct timer_list fc_disctmo;   /* Discovery rescue timer */
+        uint8_t fc_ns_retry;    /* retries for fabric nameserver */
+        uint32_t fc_prli_sent;  /* cntr for outstanding PRLIs */
+
+        spinlock_t work_port_lock;
+        uint32_t work_port_events; /* Timeout to be handled  */
+#define WORKER_DISC_TMO                0x1      /* vport: Discovery timeout */
+#define WORKER_ELS_TMO                 0x2      /* vport: ELS timeout */
+#define WORKER_FDMI_TMO                0x4      /* vport: FDMI timeout */
+
+#define WORKER_MBOX_TMO                0x100    /* hba: MBOX timeout */
+#define WORKER_HB_TMO                  0x200    /* hba: Heart beat timeout */
+#define WORKER_FABRIC_BLOCK_TMO        0x400    /* hba: fabric block timout */
+#define WORKER_RAMP_DOWN_QUEUE         0x800    /* hba: Decrease Q depth */
+#define WORKER_RAMP_UP_QUEUE           0x1000   /* hba: Increase Q depth */
+
+        struct timer_list fc_fdmitmo;
+        struct timer_list els_tmofunc;
+
+        int unreg_vpi_cmpl;
+
+        uint8_t load_flag;
+#define FC_LOADING              0x1     /* HBA in process of loading drvr */
+#define FC_UNLOADING            0x2     /* HBA in process of unloading drvr */
+        char  *vname;                   /* Application assigned name */
+        struct fc_vport *fc_vport;
+
+#ifdef CONFIG_LPFC_DEBUG_FS
+        struct dentry *debug_disc_trc;
+        struct dentry *debug_nodelist;
+        struct dentry *vport_debugfs_root;
+        struct lpfc_disc_trc *disc_trc;
+        atomic_t disc_trc_cnt;
+#endif
+};
+
+struct hbq_s {
+        uint16_t entry_count;     /* Current number of HBQ slots */
+        uint32_t next_hbqPutIdx;  /* Index to next HBQ slot to use */
+        uint32_t hbqPutIdx;       /* HBQ slot to use */
+        uint32_t local_hbqGetIdx; /* Local copy of Get index from Port */
+};
+
+#define LPFC_MAX_HBQS  16
+/* this matches the possition in the lpfc_hbq_defs array */
+#define LPFC_ELS_HBQ    0
+
 struct lpfc_hba {
         struct lpfc_sli sli;
+        uint32_t sli_rev;               /* SLI2 or SLI3 */
+        uint32_t sli3_options;          /* Mask of enabled SLI3 options */
+#define LPFC_SLI3_ENABLED        0x01
+#define LPFC_SLI3_HBQ_ENABLED    0x02
+#define LPFC_SLI3_NPIV_ENABLED   0x04
+#define LPFC_SLI3_VPORT_TEARDOWN 0x08
+        uint32_t iocb_cmd_size;
+        uint32_t iocb_rsp_size;
+
+        enum hba_state link_state;
+        uint32_t link_flag;     /* link state flags */
+#define LS_LOOPBACK_MODE      0x1       /* NPort is in Loopback mode */
+                                        /* This flag is set while issuing */
+                                        /* INIT_LINK mailbox command */
+#define LS_NPIV_FAB_SUPPORTED 0x2       /* Fabric supports NPIV */
+#define LS_IGNORE_ERATT       0x3       /* intr handler should ignore ERATT */
+
         struct lpfc_sli2_slim *slim2p;
+        struct lpfc_dmabuf hbqslimp;
+
         dma_addr_t slim2p_mapping;
+
         uint16_t pci_cfg_value;
 
-        int32_t hba_state;
-
-#define LPFC_STATE_UNKNOWN        0    /* HBA state is unknown */
-#define LPFC_WARM_START           1    /* HBA state after selective reset */
-#define LPFC_INIT_START           2    /* Initial state after board reset */
-#define LPFC_INIT_MBX_CMDS        3    /* Initialize HBA with mbox commands */
-#define LPFC_LINK_DOWN            4    /* HBA initialized, link is down */
-#define LPFC_LINK_UP              5    /* Link is up  - issue READ_LA */
-#define LPFC_LOCAL_CFG_LINK       6    /* local NPORT Id configured */
-#define LPFC_FLOGI                7    /* FLOGI sent to Fabric */
-#define LPFC_FABRIC_CFG_LINK      8    /* Fabric assigned NPORT Id
-                                           configured */
-#define LPFC_NS_REG               9     /* Register with NameServer */
-#define LPFC_NS_QRY               10    /* Query NameServer for NPort ID list */
-#define LPFC_BUILD_DISC_LIST      11    /* Build ADISC and PLOGI lists for
-                                         * device authentication / discovery */
-#define LPFC_DISC_AUTH            12    /* Processing ADISC list */
-#define LPFC_CLEAR_LA             13    /* authentication cmplt - issue
-                                           CLEAR_LA */
-#define LPFC_HBA_READY            32
-#define LPFC_HBA_ERROR            -1
+        uint8_t work_found;
+#define LPFC_MAX_WORKER_ITERATION  4
 
-        int32_t stopped;   /* HBA has not been restarted since last ERATT */
         uint8_t fc_linkspeed;   /* Link speed after last READ_LA */
 
         uint32_t fc_eventTag;   /* event tag for link attention */
-        uint32_t fc_prli_sent;  /* cntr for outstanding PRLIs */
 
-        uint32_t num_disc_nodes;        /*in addition to hba_state */
 
         struct timer_list fc_estabtmo;  /* link establishment timer */
-        struct timer_list fc_disctmo;   /* Discovery rescue timer */
-        struct timer_list fc_fdmitmo;   /* fdmi timer */
         /* These fields used to be binfo */
-        struct lpfc_name fc_nodename;   /* fc nodename */
-        struct lpfc_name fc_portname;   /* fc portname */
         uint32_t fc_pref_DID;   /* preferred D_ID */
-        uint8_t fc_pref_ALPA;   /* preferred AL_PA */
+        uint8_t  fc_pref_ALPA;  /* preferred AL_PA */
         uint32_t fc_edtov;      /* E_D_TOV timer value */
         uint32_t fc_arbtov;     /* ARB_TOV timer value */
         uint32_t fc_ratov;      /* R_A_TOV timer value */
@@ -216,61 +396,21 @@ struct lpfc_hba {
         uint32_t fc_altov;      /* AL_TOV timer value */
         uint32_t fc_crtov;      /* C_R_TOV timer value */
         uint32_t fc_citov;      /* C_I_TOV timer value */
-        uint32_t fc_myDID;      /* fibre channel S_ID */
-        uint32_t fc_prevDID;    /* previous fibre channel S_ID */
 
-        struct serv_parm fc_sparam;     /* buffer for our service parameters */
         struct serv_parm fc_fabparam;   /* fabric service parameters buffer */
         uint8_t alpa_map[128];  /* AL_PA map from READ_LA */
 
-        uint8_t fc_ns_retry;    /* retries for fabric nameserver */
-        uint32_t fc_nlp_cnt;    /* outstanding NODELIST requests */
-        uint32_t fc_rscn_id_cnt;        /* count of RSCNs payloads in list */
-        struct lpfc_dmabuf *fc_rscn_id_list[FC_MAX_HOLD_RSCN];
         uint32_t lmt;
-        uint32_t fc_flag;       /* FC flags */
-#define FC_PT2PT                0x1     /* pt2pt with no fabric */
-#define FC_PT2PT_PLOGI          0x2     /* pt2pt initiate PLOGI */
-#define FC_DISC_TMO             0x4     /* Discovery timer running */
-#define FC_PUBLIC_LOOP          0x8     /* Public loop */
-#define FC_LBIT                 0x10    /* LOGIN bit in loopinit set */
-#define FC_RSCN_MODE            0x20    /* RSCN cmd rcv'ed */
-#define FC_NLP_MORE             0x40    /* More node to process in node tbl */
-#define FC_OFFLINE_MODE         0x80    /* Interface is offline for diag */
-#define FC_FABRIC               0x100   /* We are fabric attached */
-#define FC_ESTABLISH_LINK       0x200   /* Reestablish Link */
-#define FC_RSCN_DISCOVERY       0x400   /* Authenticate all devices after RSCN*/
-#define FC_BLOCK_MGMT_IO        0x800   /* Don't allow mgmt mbx or iocb cmds */
-#define FC_LOADING              0x1000  /* HBA in process of loading drvr */
-#define FC_UNLOADING            0x2000  /* HBA in process of unloading drvr */
-#define FC_SCSI_SCAN_TMO        0x4000  /* scsi scan timer running */
-#define FC_ABORT_DISCOVERY      0x8000  /* we want to abort discovery */
-#define FC_NDISC_ACTIVE         0x10000 /* NPort discovery active */
-#define FC_BYPASSED_MODE        0x20000 /* NPort is in bypassed mode */
-#define FC_LOOPBACK_MODE        0x40000 /* NPort is in Loopback mode */
-                                        /* This flag is set while issuing */
-                                        /* INIT_LINK mailbox command */
-#define FC_IGNORE_ERATT         0x80000 /* intr handler should ignore ERATT */
 
         uint32_t fc_topology;   /* link topology, from LINK INIT */
 
         struct lpfc_stats fc_stat;
 
-        struct list_head fc_nodes;
-
-        /* Keep counters for the number of entries in each list. */
-        uint16_t fc_plogi_cnt;
-        uint16_t fc_adisc_cnt;
-        uint16_t fc_reglogin_cnt;
-        uint16_t fc_prli_cnt;
-        uint16_t fc_unmap_cnt;
-        uint16_t fc_map_cnt;
-        uint16_t fc_npr_cnt;
-        uint16_t fc_unused_cnt;
         struct lpfc_nodelist fc_fcpnodev; /* nodelist entry for no device */
         uint32_t nport_event_cnt;       /* timestamp for nlplist entry */
 
-        uint32_t wwnn[2];
+        uint8_t  wwnn[8];
+        uint8_t  wwpn[8];
         uint32_t RandomData[7];
 
         uint32_t cfg_log_verbose;
@@ -278,6 +418,9 @@ struct lpfc_hba {
         uint32_t cfg_nodev_tmo;
         uint32_t cfg_devloss_tmo;
         uint32_t cfg_hba_queue_depth;
+        uint32_t cfg_peer_port_login;
+        uint32_t cfg_vport_restrict_login;
+        uint32_t cfg_npiv_enable;
         uint32_t cfg_fcp_class;
         uint32_t cfg_use_adisc;
         uint32_t cfg_ack0;
@@ -304,22 +447,20 @@ struct lpfc_hba {
 
         lpfc_vpd_t vpd;         /* vital product data */
 
-        struct Scsi_Host *host;
         struct pci_dev *pcidev;
         struct list_head      work_list;
         uint32_t              work_ha;      /* Host Attention Bits for WT */
         uint32_t              work_ha_mask; /* HA Bits owned by WT        */
         uint32_t              work_hs;      /* HS stored in case of ERRAT */
         uint32_t              work_status[2]; /* Extra status from SLIM */
-        uint32_t              work_hba_events; /* Timeout to be handled  */
-#define WORKER_DISC_TMO                0x1      /* Discovery timeout */
-#define WORKER_ELS_TMO                 0x2      /* ELS timeout */
-#define WORKER_MBOX_TMO                0x4      /* MBOX timeout */
-#define WORKER_FDMI_TMO                0x8      /* FDMI timeout */
 
         wait_queue_head_t    *work_wait;
         struct task_struct   *worker_thread;
 
+        struct list_head hbq_buffer_list;
+        uint32_t hbq_count;             /* Count of configured HBQs */
+        struct hbq_s hbqs[LPFC_MAX_HBQS]; /* local copy of hbq indicies  */
+
         unsigned long pci_bar0_map;     /* Physical address for PCI BAR0 */
         unsigned long pci_bar2_map;     /* Physical address for PCI BAR2 */
         void __iomem *slim_memmap_p;    /* Kernel memory mapped address for
@@ -334,6 +475,10 @@ struct lpfc_hba {
                                            reg */
         void __iomem *HCregaddr;        /* virtual address for host ctl reg */
 
+        struct lpfc_hgp __iomem *host_gp; /* Host side get/put pointers */
+        uint32_t __iomem  *hbq_put;     /* Address in SLIM to HBQ put ptrs */
+        uint32_t          *hbq_get;     /* Host mem address of HBQ get ptrs */
+
         int brd_no;                     /* FC board number */
 
         char SerialNumber[32];          /* adapter Serial Number */
@@ -353,7 +498,6 @@ struct lpfc_hba {
         uint8_t soft_wwn_enable;
 
         struct timer_list fcp_poll_timer;
-        struct timer_list els_tmofunc;
 
         /*
          * stat  counters
@@ -370,31 +514,69 @@ struct lpfc_hba {
         uint32_t total_scsi_bufs;
         struct list_head lpfc_iocb_list;
         uint32_t total_iocbq_bufs;
+        spinlock_t hbalock;
 
         /* pci_mem_pools */
         struct pci_pool *lpfc_scsi_dma_buf_pool;
         struct pci_pool *lpfc_mbuf_pool;
+        struct pci_pool *lpfc_hbq_pool;
         struct lpfc_dma_pool lpfc_mbuf_safety_pool;
 
         mempool_t *mbox_mem_pool;
         mempool_t *nlp_mem_pool;
 
         struct fc_host_statistics link_stats;
+
+        struct list_head port_list;
+        struct lpfc_vport *pport; /* physical lpfc_vport pointer */
+        uint16_t max_vpi;       /* Maximum virtual nports */
+#define LPFC_MAX_VPI 100  /* Max number of VPorts supported */
+        unsigned long *vpi_bmask; /* vpi allocation table */
+
+        /* Data structure used by fabric iocb scheduler */
+        struct list_head fabric_iocb_list;
+        atomic_t fabric_iocb_count;
+        struct timer_list fabric_block_timer;
+        unsigned long bit_flags;
+#define FABRIC_COMANDS_BLOCKED  0
+        atomic_t num_rsrc_err;
+        atomic_t num_cmd_success;
+        unsigned long last_rsrc_error_time;
+        unsigned long last_ramp_down_time;
+        unsigned long last_ramp_up_time;
+#ifdef CONFIG_LPFC_DEBUG_FS
+        struct dentry *hba_debugfs_root;
+        atomic_t debugfs_vport_count;
+#endif
+
+        /* Fields used for heart beat. */
+        unsigned long last_completion_time;
+        struct timer_list hb_tmofunc;
+        uint8_t hb_outstanding;
 };
 
+static inline struct Scsi_Host *
+lpfc_shost_from_vport(struct lpfc_vport *vport)
+{
+        return container_of((void *) vport, struct Scsi_Host, hostdata[0]);
+}
+
 static inline void
-lpfc_set_loopback_flag(struct lpfc_hba *phba) {
+lpfc_set_loopback_flag(struct lpfc_hba *phba)
+{
         if (phba->cfg_topology == FLAGS_LOCAL_LB)
-                phba->fc_flag |= FC_LOOPBACK_MODE;
+                phba->link_flag |= LS_LOOPBACK_MODE;
         else
-                phba->fc_flag &= ~FC_LOOPBACK_MODE;
+                phba->link_flag &= ~LS_LOOPBACK_MODE;
 }
 
-struct rnidrsp {
-        void *buf;
-        uint32_t uniqueid;
-        struct list_head list;
-        uint32_t data;
-};
+static inline int
+lpfc_is_link_up(struct lpfc_hba *phba)
+{
+        return  phba->link_state == LPFC_LINK_UP ||
+                phba->link_state == LPFC_CLEAR_LA ||
+                phba->link_state == LPFC_HBA_READY;
+}
 
 #define FC_REG_DUMP_EVENT       0x10    /* Register for Dump events */
+