diff options
Diffstat (limited to 'drivers/net/wireless/hermes.h')
-rw-r--r-- | drivers/net/wireless/hermes.h | 481 |
1 files changed, 481 insertions, 0 deletions
diff --git a/drivers/net/wireless/hermes.h b/drivers/net/wireless/hermes.h new file mode 100644 index 000000000000..8c9e874c9118 --- /dev/null +++ b/drivers/net/wireless/hermes.h | |||
@@ -0,0 +1,481 @@ | |||
1 | /* hermes.h | ||
2 | * | ||
3 | * Driver core for the "Hermes" wireless MAC controller, as used in | ||
4 | * the Lucent Orinoco and Cabletron RoamAbout cards. It should also | ||
5 | * work on the hfa3841 and hfa3842 MAC controller chips used in the | ||
6 | * Prism I & II chipsets. | ||
7 | * | ||
8 | * This is not a complete driver, just low-level access routines for | ||
9 | * the MAC controller itself. | ||
10 | * | ||
11 | * Based on the prism2 driver from Absolute Value Systems' linux-wlan | ||
12 | * project, the Linux wvlan_cs driver, Lucent's HCF-Light | ||
13 | * (wvlan_hcf.c) library, and the NetBSD wireless driver. | ||
14 | * | ||
15 | * Copyright (C) 2000, David Gibson, Linuxcare Australia. | ||
16 | * (C) Copyright David Gibson, IBM Corp. 2001-2003. | ||
17 | * | ||
18 | * Portions taken from hfa384x.h, Copyright (C) 1999 AbsoluteValue Systems, Inc. All Rights Reserved. | ||
19 | * | ||
20 | * This file distributed under the GPL, version 2. | ||
21 | */ | ||
22 | |||
23 | #ifndef _HERMES_H | ||
24 | #define _HERMES_H | ||
25 | |||
26 | /* Notes on locking: | ||
27 | * | ||
28 | * As a module of low level hardware access routines, there is no | ||
29 | * locking. Users of this module should ensure that they serialize | ||
30 | * access to the hermes_t structure, and to the hardware | ||
31 | */ | ||
32 | |||
33 | #include <linux/delay.h> | ||
34 | #include <linux/if_ether.h> | ||
35 | #include <asm/byteorder.h> | ||
36 | |||
37 | /* | ||
38 | * Limits and constants | ||
39 | */ | ||
40 | #define HERMES_ALLOC_LEN_MIN (4) | ||
41 | #define HERMES_ALLOC_LEN_MAX (2400) | ||
42 | #define HERMES_LTV_LEN_MAX (34) | ||
43 | #define HERMES_BAP_DATALEN_MAX (4096) | ||
44 | #define HERMES_BAP_OFFSET_MAX (4096) | ||
45 | #define HERMES_PORTID_MAX (7) | ||
46 | #define HERMES_NUMPORTS_MAX (HERMES_PORTID_MAX+1) | ||
47 | #define HERMES_PDR_LEN_MAX (260) /* in bytes, from EK */ | ||
48 | #define HERMES_PDA_RECS_MAX (200) /* a guess */ | ||
49 | #define HERMES_PDA_LEN_MAX (1024) /* in bytes, from EK */ | ||
50 | #define HERMES_SCANRESULT_MAX (35) | ||
51 | #define HERMES_CHINFORESULT_MAX (8) | ||
52 | #define HERMES_MAX_MULTICAST (16) | ||
53 | #define HERMES_MAGIC (0x7d1f) | ||
54 | |||
55 | /* | ||
56 | * Hermes register offsets | ||
57 | */ | ||
58 | #define HERMES_CMD (0x00) | ||
59 | #define HERMES_PARAM0 (0x02) | ||
60 | #define HERMES_PARAM1 (0x04) | ||
61 | #define HERMES_PARAM2 (0x06) | ||
62 | #define HERMES_STATUS (0x08) | ||
63 | #define HERMES_RESP0 (0x0A) | ||
64 | #define HERMES_RESP1 (0x0C) | ||
65 | #define HERMES_RESP2 (0x0E) | ||
66 | #define HERMES_INFOFID (0x10) | ||
67 | #define HERMES_RXFID (0x20) | ||
68 | #define HERMES_ALLOCFID (0x22) | ||
69 | #define HERMES_TXCOMPLFID (0x24) | ||
70 | #define HERMES_SELECT0 (0x18) | ||
71 | #define HERMES_OFFSET0 (0x1C) | ||
72 | #define HERMES_DATA0 (0x36) | ||
73 | #define HERMES_SELECT1 (0x1A) | ||
74 | #define HERMES_OFFSET1 (0x1E) | ||
75 | #define HERMES_DATA1 (0x38) | ||
76 | #define HERMES_EVSTAT (0x30) | ||
77 | #define HERMES_INTEN (0x32) | ||
78 | #define HERMES_EVACK (0x34) | ||
79 | #define HERMES_CONTROL (0x14) | ||
80 | #define HERMES_SWSUPPORT0 (0x28) | ||
81 | #define HERMES_SWSUPPORT1 (0x2A) | ||
82 | #define HERMES_SWSUPPORT2 (0x2C) | ||
83 | #define HERMES_AUXPAGE (0x3A) | ||
84 | #define HERMES_AUXOFFSET (0x3C) | ||
85 | #define HERMES_AUXDATA (0x3E) | ||
86 | |||
87 | /* | ||
88 | * CMD register bitmasks | ||
89 | */ | ||
90 | #define HERMES_CMD_BUSY (0x8000) | ||
91 | #define HERMES_CMD_AINFO (0x7f00) | ||
92 | #define HERMES_CMD_MACPORT (0x0700) | ||
93 | #define HERMES_CMD_RECL (0x0100) | ||
94 | #define HERMES_CMD_WRITE (0x0100) | ||
95 | #define HERMES_CMD_PROGMODE (0x0300) | ||
96 | #define HERMES_CMD_CMDCODE (0x003f) | ||
97 | |||
98 | /* | ||
99 | * STATUS register bitmasks | ||
100 | */ | ||
101 | #define HERMES_STATUS_RESULT (0x7f00) | ||
102 | #define HERMES_STATUS_CMDCODE (0x003f) | ||
103 | |||
104 | /* | ||
105 | * OFFSET register bitmasks | ||
106 | */ | ||
107 | #define HERMES_OFFSET_BUSY (0x8000) | ||
108 | #define HERMES_OFFSET_ERR (0x4000) | ||
109 | #define HERMES_OFFSET_DATAOFF (0x0ffe) | ||
110 | |||
111 | /* | ||
112 | * Event register bitmasks (INTEN, EVSTAT, EVACK) | ||
113 | */ | ||
114 | #define HERMES_EV_TICK (0x8000) | ||
115 | #define HERMES_EV_WTERR (0x4000) | ||
116 | #define HERMES_EV_INFDROP (0x2000) | ||
117 | #define HERMES_EV_INFO (0x0080) | ||
118 | #define HERMES_EV_DTIM (0x0020) | ||
119 | #define HERMES_EV_CMD (0x0010) | ||
120 | #define HERMES_EV_ALLOC (0x0008) | ||
121 | #define HERMES_EV_TXEXC (0x0004) | ||
122 | #define HERMES_EV_TX (0x0002) | ||
123 | #define HERMES_EV_RX (0x0001) | ||
124 | |||
125 | /* | ||
126 | * Command codes | ||
127 | */ | ||
128 | /*--- Controller Commands ----------------------------*/ | ||
129 | #define HERMES_CMD_INIT (0x0000) | ||
130 | #define HERMES_CMD_ENABLE (0x0001) | ||
131 | #define HERMES_CMD_DISABLE (0x0002) | ||
132 | #define HERMES_CMD_DIAG (0x0003) | ||
133 | |||
134 | /*--- Buffer Mgmt Commands ---------------------------*/ | ||
135 | #define HERMES_CMD_ALLOC (0x000A) | ||
136 | #define HERMES_CMD_TX (0x000B) | ||
137 | |||
138 | /*--- Regulate Commands ------------------------------*/ | ||
139 | #define HERMES_CMD_NOTIFY (0x0010) | ||
140 | #define HERMES_CMD_INQUIRE (0x0011) | ||
141 | |||
142 | /*--- Configure Commands -----------------------------*/ | ||
143 | #define HERMES_CMD_ACCESS (0x0021) | ||
144 | #define HERMES_CMD_DOWNLD (0x0022) | ||
145 | |||
146 | /*--- Serial I/O Commands ----------------------------*/ | ||
147 | #define HERMES_CMD_READMIF (0x0030) | ||
148 | #define HERMES_CMD_WRITEMIF (0x0031) | ||
149 | |||
150 | /*--- Debugging Commands -----------------------------*/ | ||
151 | #define HERMES_CMD_TEST (0x0038) | ||
152 | |||
153 | |||
154 | /* Test command arguments */ | ||
155 | #define HERMES_TEST_SET_CHANNEL 0x0800 | ||
156 | #define HERMES_TEST_MONITOR 0x0b00 | ||
157 | #define HERMES_TEST_STOP 0x0f00 | ||
158 | |||
159 | /* Authentication algorithms */ | ||
160 | #define HERMES_AUTH_OPEN 1 | ||
161 | #define HERMES_AUTH_SHARED_KEY 2 | ||
162 | |||
163 | /* WEP settings */ | ||
164 | #define HERMES_WEP_PRIVACY_INVOKED 0x0001 | ||
165 | #define HERMES_WEP_EXCL_UNENCRYPTED 0x0002 | ||
166 | #define HERMES_WEP_HOST_ENCRYPT 0x0010 | ||
167 | #define HERMES_WEP_HOST_DECRYPT 0x0080 | ||
168 | |||
169 | /* Symbol hostscan options */ | ||
170 | #define HERMES_HOSTSCAN_SYMBOL_5SEC 0x0001 | ||
171 | #define HERMES_HOSTSCAN_SYMBOL_ONCE 0x0002 | ||
172 | #define HERMES_HOSTSCAN_SYMBOL_PASSIVE 0x0040 | ||
173 | #define HERMES_HOSTSCAN_SYMBOL_BCAST 0x0080 | ||
174 | |||
175 | /* | ||
176 | * Frame structures and constants | ||
177 | */ | ||
178 | |||
179 | #define HERMES_DESCRIPTOR_OFFSET 0 | ||
180 | #define HERMES_802_11_OFFSET (14) | ||
181 | #define HERMES_802_3_OFFSET (14+32) | ||
182 | #define HERMES_802_2_OFFSET (14+32+14) | ||
183 | |||
184 | #define HERMES_RXSTAT_ERR (0x0003) | ||
185 | #define HERMES_RXSTAT_BADCRC (0x0001) | ||
186 | #define HERMES_RXSTAT_UNDECRYPTABLE (0x0002) | ||
187 | #define HERMES_RXSTAT_MACPORT (0x0700) | ||
188 | #define HERMES_RXSTAT_PCF (0x1000) /* Frame was received in CF period */ | ||
189 | #define HERMES_RXSTAT_MSGTYPE (0xE000) | ||
190 | #define HERMES_RXSTAT_1042 (0x2000) /* RFC-1042 frame */ | ||
191 | #define HERMES_RXSTAT_TUNNEL (0x4000) /* bridge-tunnel encoded frame */ | ||
192 | #define HERMES_RXSTAT_WMP (0x6000) /* Wavelan-II Management Protocol frame */ | ||
193 | |||
194 | struct hermes_tx_descriptor { | ||
195 | u16 status; | ||
196 | u16 reserved1; | ||
197 | u16 reserved2; | ||
198 | u32 sw_support; | ||
199 | u8 retry_count; | ||
200 | u8 tx_rate; | ||
201 | u16 tx_control; | ||
202 | } __attribute__ ((packed)); | ||
203 | |||
204 | #define HERMES_TXSTAT_RETRYERR (0x0001) | ||
205 | #define HERMES_TXSTAT_AGEDERR (0x0002) | ||
206 | #define HERMES_TXSTAT_DISCON (0x0004) | ||
207 | #define HERMES_TXSTAT_FORMERR (0x0008) | ||
208 | |||
209 | #define HERMES_TXCTRL_TX_OK (0x0002) /* ?? interrupt on Tx complete */ | ||
210 | #define HERMES_TXCTRL_TX_EX (0x0004) /* ?? interrupt on Tx exception */ | ||
211 | #define HERMES_TXCTRL_802_11 (0x0008) /* We supply 802.11 header */ | ||
212 | #define HERMES_TXCTRL_ALT_RTRY (0x0020) | ||
213 | |||
214 | /* Inquiry constants and data types */ | ||
215 | |||
216 | #define HERMES_INQ_TALLIES (0xF100) | ||
217 | #define HERMES_INQ_SCAN (0xF101) | ||
218 | #define HERMES_INQ_CHANNELINFO (0xF102) | ||
219 | #define HERMES_INQ_HOSTSCAN (0xF103) | ||
220 | #define HERMES_INQ_HOSTSCAN_SYMBOL (0xF104) | ||
221 | #define HERMES_INQ_LINKSTATUS (0xF200) | ||
222 | #define HERMES_INQ_SEC_STAT_AGERE (0xF202) | ||
223 | |||
224 | struct hermes_tallies_frame { | ||
225 | u16 TxUnicastFrames; | ||
226 | u16 TxMulticastFrames; | ||
227 | u16 TxFragments; | ||
228 | u16 TxUnicastOctets; | ||
229 | u16 TxMulticastOctets; | ||
230 | u16 TxDeferredTransmissions; | ||
231 | u16 TxSingleRetryFrames; | ||
232 | u16 TxMultipleRetryFrames; | ||
233 | u16 TxRetryLimitExceeded; | ||
234 | u16 TxDiscards; | ||
235 | u16 RxUnicastFrames; | ||
236 | u16 RxMulticastFrames; | ||
237 | u16 RxFragments; | ||
238 | u16 RxUnicastOctets; | ||
239 | u16 RxMulticastOctets; | ||
240 | u16 RxFCSErrors; | ||
241 | u16 RxDiscards_NoBuffer; | ||
242 | u16 TxDiscardsWrongSA; | ||
243 | u16 RxWEPUndecryptable; | ||
244 | u16 RxMsgInMsgFragments; | ||
245 | u16 RxMsgInBadMsgFragments; | ||
246 | /* Those last are probably not available in very old firmwares */ | ||
247 | u16 RxDiscards_WEPICVError; | ||
248 | u16 RxDiscards_WEPExcluded; | ||
249 | } __attribute__ ((packed)); | ||
250 | |||
251 | /* Grabbed from wlan-ng - Thanks Mark... - Jean II | ||
252 | * This is the result of a scan inquiry command */ | ||
253 | /* Structure describing info about an Access Point */ | ||
254 | struct prism2_scan_apinfo { | ||
255 | u16 channel; /* Channel where the AP sits */ | ||
256 | u16 noise; /* Noise level */ | ||
257 | u16 level; /* Signal level */ | ||
258 | u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */ | ||
259 | u16 beacon_interv; /* Beacon interval */ | ||
260 | u16 capabilities; /* Capabilities */ | ||
261 | u16 essid_len; /* ESSID length */ | ||
262 | u8 essid[32]; /* ESSID of the network */ | ||
263 | u8 rates[10]; /* Bit rate supported */ | ||
264 | u16 proberesp_rate; /* Data rate of the response frame */ | ||
265 | u16 atim; /* ATIM window time, Kus (hostscan only) */ | ||
266 | } __attribute__ ((packed)); | ||
267 | |||
268 | /* Same stuff for the Lucent/Agere card. | ||
269 | * Thanks to h1kari <h1kari AT dachb0den.com> - Jean II */ | ||
270 | struct agere_scan_apinfo { | ||
271 | u16 channel; /* Channel where the AP sits */ | ||
272 | u16 noise; /* Noise level */ | ||
273 | u16 level; /* Signal level */ | ||
274 | u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */ | ||
275 | u16 beacon_interv; /* Beacon interval */ | ||
276 | u16 capabilities; /* Capabilities */ | ||
277 | /* bits: 0-ess, 1-ibss, 4-privacy [wep] */ | ||
278 | u16 essid_len; /* ESSID length */ | ||
279 | u8 essid[32]; /* ESSID of the network */ | ||
280 | } __attribute__ ((packed)); | ||
281 | |||
282 | /* Moustafa: Scan structure for Symbol cards */ | ||
283 | struct symbol_scan_apinfo { | ||
284 | u8 channel; /* Channel where the AP sits */ | ||
285 | u8 unknown1; /* 8 in 2.9x and 3.9x f/w, 0 otherwise */ | ||
286 | u16 noise; /* Noise level */ | ||
287 | u16 level; /* Signal level */ | ||
288 | u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */ | ||
289 | u16 beacon_interv; /* Beacon interval */ | ||
290 | u16 capabilities; /* Capabilities */ | ||
291 | /* bits: 0-ess, 1-ibss, 4-privacy [wep] */ | ||
292 | u16 essid_len; /* ESSID length */ | ||
293 | u8 essid[32]; /* ESSID of the network */ | ||
294 | u16 rates[5]; /* Bit rate supported */ | ||
295 | u16 basic_rates; /* Basic rates bitmask */ | ||
296 | u8 unknown2[6]; /* Always FF:FF:FF:FF:00:00 */ | ||
297 | u8 unknown3[8]; /* Always 0, appeared in f/w 3.91-68 */ | ||
298 | } __attribute__ ((packed)); | ||
299 | |||
300 | union hermes_scan_info { | ||
301 | struct agere_scan_apinfo a; | ||
302 | struct prism2_scan_apinfo p; | ||
303 | struct symbol_scan_apinfo s; | ||
304 | }; | ||
305 | |||
306 | #define HERMES_LINKSTATUS_NOT_CONNECTED (0x0000) | ||
307 | #define HERMES_LINKSTATUS_CONNECTED (0x0001) | ||
308 | #define HERMES_LINKSTATUS_DISCONNECTED (0x0002) | ||
309 | #define HERMES_LINKSTATUS_AP_CHANGE (0x0003) | ||
310 | #define HERMES_LINKSTATUS_AP_OUT_OF_RANGE (0x0004) | ||
311 | #define HERMES_LINKSTATUS_AP_IN_RANGE (0x0005) | ||
312 | #define HERMES_LINKSTATUS_ASSOC_FAILED (0x0006) | ||
313 | |||
314 | struct hermes_linkstatus { | ||
315 | u16 linkstatus; /* Link status */ | ||
316 | } __attribute__ ((packed)); | ||
317 | |||
318 | struct hermes_response { | ||
319 | u16 status, resp0, resp1, resp2; | ||
320 | }; | ||
321 | |||
322 | /* "ID" structure - used for ESSID and station nickname */ | ||
323 | struct hermes_idstring { | ||
324 | u16 len; | ||
325 | u16 val[16]; | ||
326 | } __attribute__ ((packed)); | ||
327 | |||
328 | struct hermes_multicast { | ||
329 | u8 addr[HERMES_MAX_MULTICAST][ETH_ALEN]; | ||
330 | } __attribute__ ((packed)); | ||
331 | |||
332 | // #define HERMES_DEBUG_BUFFER 1 | ||
333 | #define HERMES_DEBUG_BUFSIZE 4096 | ||
334 | struct hermes_debug_entry { | ||
335 | int bap; | ||
336 | u16 id, offset; | ||
337 | int cycles; | ||
338 | }; | ||
339 | |||
340 | #ifdef __KERNEL__ | ||
341 | |||
342 | /* Timeouts */ | ||
343 | #define HERMES_BAP_BUSY_TIMEOUT (10000) /* In iterations of ~1us */ | ||
344 | |||
345 | /* Basic control structure */ | ||
346 | typedef struct hermes { | ||
347 | void __iomem *iobase; | ||
348 | int reg_spacing; | ||
349 | #define HERMES_16BIT_REGSPACING 0 | ||
350 | #define HERMES_32BIT_REGSPACING 1 | ||
351 | |||
352 | u16 inten; /* Which interrupts should be enabled? */ | ||
353 | |||
354 | #ifdef HERMES_DEBUG_BUFFER | ||
355 | struct hermes_debug_entry dbuf[HERMES_DEBUG_BUFSIZE]; | ||
356 | unsigned long dbufp; | ||
357 | unsigned long profile[HERMES_BAP_BUSY_TIMEOUT+1]; | ||
358 | #endif | ||
359 | } hermes_t; | ||
360 | |||
361 | /* Register access convenience macros */ | ||
362 | #define hermes_read_reg(hw, off) \ | ||
363 | (ioread16((hw)->iobase + ( (off) << (hw)->reg_spacing ))) | ||
364 | #define hermes_write_reg(hw, off, val) \ | ||
365 | (iowrite16((val), (hw)->iobase + ((off) << (hw)->reg_spacing))) | ||
366 | #define hermes_read_regn(hw, name) hermes_read_reg((hw), HERMES_##name) | ||
367 | #define hermes_write_regn(hw, name, val) hermes_write_reg((hw), HERMES_##name, (val)) | ||
368 | |||
369 | /* Function prototypes */ | ||
370 | void hermes_struct_init(hermes_t *hw, void __iomem *address, int reg_spacing); | ||
371 | int hermes_init(hermes_t *hw); | ||
372 | int hermes_docmd_wait(hermes_t *hw, u16 cmd, u16 parm0, | ||
373 | struct hermes_response *resp); | ||
374 | int hermes_allocate(hermes_t *hw, u16 size, u16 *fid); | ||
375 | |||
376 | int hermes_bap_pread(hermes_t *hw, int bap, void *buf, unsigned len, | ||
377 | u16 id, u16 offset); | ||
378 | int hermes_bap_pwrite(hermes_t *hw, int bap, const void *buf, unsigned len, | ||
379 | u16 id, u16 offset); | ||
380 | int hermes_read_ltv(hermes_t *hw, int bap, u16 rid, unsigned buflen, | ||
381 | u16 *length, void *buf); | ||
382 | int hermes_write_ltv(hermes_t *hw, int bap, u16 rid, | ||
383 | u16 length, const void *value); | ||
384 | |||
385 | /* Inline functions */ | ||
386 | |||
387 | static inline int hermes_present(hermes_t *hw) | ||
388 | { | ||
389 | return hermes_read_regn(hw, SWSUPPORT0) == HERMES_MAGIC; | ||
390 | } | ||
391 | |||
392 | static inline void hermes_set_irqmask(hermes_t *hw, u16 events) | ||
393 | { | ||
394 | hw->inten = events; | ||
395 | hermes_write_regn(hw, INTEN, events); | ||
396 | } | ||
397 | |||
398 | static inline int hermes_enable_port(hermes_t *hw, int port) | ||
399 | { | ||
400 | return hermes_docmd_wait(hw, HERMES_CMD_ENABLE | (port << 8), | ||
401 | 0, NULL); | ||
402 | } | ||
403 | |||
404 | static inline int hermes_disable_port(hermes_t *hw, int port) | ||
405 | { | ||
406 | return hermes_docmd_wait(hw, HERMES_CMD_DISABLE | (port << 8), | ||
407 | 0, NULL); | ||
408 | } | ||
409 | |||
410 | /* Initiate an INQUIRE command (tallies or scan). The result will come as an | ||
411 | * information frame in __orinoco_ev_info() */ | ||
412 | static inline int hermes_inquire(hermes_t *hw, u16 rid) | ||
413 | { | ||
414 | return hermes_docmd_wait(hw, HERMES_CMD_INQUIRE, rid, NULL); | ||
415 | } | ||
416 | |||
417 | #define HERMES_BYTES_TO_RECLEN(n) ( (((n)+1)/2) + 1 ) | ||
418 | #define HERMES_RECLEN_TO_BYTES(n) ( ((n)-1) * 2 ) | ||
419 | |||
420 | /* Note that for the next two, the count is in 16-bit words, not bytes */ | ||
421 | static inline void hermes_read_words(struct hermes *hw, int off, void *buf, unsigned count) | ||
422 | { | ||
423 | off = off << hw->reg_spacing; | ||
424 | ioread16_rep(hw->iobase + off, buf, count); | ||
425 | } | ||
426 | |||
427 | static inline void hermes_write_words(struct hermes *hw, int off, const void *buf, unsigned count) | ||
428 | { | ||
429 | off = off << hw->reg_spacing; | ||
430 | iowrite16_rep(hw->iobase + off, buf, count); | ||
431 | } | ||
432 | |||
433 | static inline void hermes_clear_words(struct hermes *hw, int off, unsigned count) | ||
434 | { | ||
435 | unsigned i; | ||
436 | |||
437 | off = off << hw->reg_spacing; | ||
438 | |||
439 | for (i = 0; i < count; i++) | ||
440 | iowrite16(0, hw->iobase + off); | ||
441 | } | ||
442 | |||
443 | #define HERMES_READ_RECORD(hw, bap, rid, buf) \ | ||
444 | (hermes_read_ltv((hw),(bap),(rid), sizeof(*buf), NULL, (buf))) | ||
445 | #define HERMES_WRITE_RECORD(hw, bap, rid, buf) \ | ||
446 | (hermes_write_ltv((hw),(bap),(rid),HERMES_BYTES_TO_RECLEN(sizeof(*buf)),(buf))) | ||
447 | |||
448 | static inline int hermes_read_wordrec(hermes_t *hw, int bap, u16 rid, u16 *word) | ||
449 | { | ||
450 | u16 rec; | ||
451 | int err; | ||
452 | |||
453 | err = HERMES_READ_RECORD(hw, bap, rid, &rec); | ||
454 | *word = le16_to_cpu(rec); | ||
455 | return err; | ||
456 | } | ||
457 | |||
458 | static inline int hermes_write_wordrec(hermes_t *hw, int bap, u16 rid, u16 word) | ||
459 | { | ||
460 | u16 rec = cpu_to_le16(word); | ||
461 | return HERMES_WRITE_RECORD(hw, bap, rid, &rec); | ||
462 | } | ||
463 | |||
464 | #else /* ! __KERNEL__ */ | ||
465 | |||
466 | /* These are provided for the benefit of userspace drivers and testing programs | ||
467 | which use ioperm() or iopl() */ | ||
468 | |||
469 | #define hermes_read_reg(base, off) (inw((base) + (off))) | ||
470 | #define hermes_write_reg(base, off, val) (outw((val), (base) + (off))) | ||
471 | |||
472 | #define hermes_read_regn(base, name) (hermes_read_reg((base), HERMES_##name)) | ||
473 | #define hermes_write_regn(base, name, val) (hermes_write_reg((base), HERMES_##name, (val))) | ||
474 | |||
475 | /* Note that for the next two, the count is in 16-bit words, not bytes */ | ||
476 | #define hermes_read_data(base, off, buf, count) (insw((base) + (off), (buf), (count))) | ||
477 | #define hermes_write_data(base, off, buf, count) (outsw((base) + (off), (buf), (count))) | ||
478 | |||
479 | #endif /* ! __KERNEL__ */ | ||
480 | |||
481 | #endif /* _HERMES_H */ | ||