1 files changed, 13 insertions, 16 deletions

diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c
index 6167b58d2731..663bc47c1f63 100644
--- a/drivers/net/netxen/netxen_nic_main.c
+++ b/drivers/net/netxen/netxen_nic_main.c
@@ -336,11 +336,9 @@ netxen_nic_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
         if (pci_using_dac)
                 netdev->features |= NETIF_F_HIGHDMA;
 
-        if (pci_enable_msi(pdev)) {
+        if (pci_enable_msi(pdev))
                 adapter->flags &= ~NETXEN_NIC_MSI_ENABLED;
-                printk(KERN_WARNING "%s: unable to allocate MSI interrupt"
-                       " error\n", netxen_nic_driver_name);
-        } else
+        else
                 adapter->flags |= NETXEN_NIC_MSI_ENABLED;
 
         netdev->irq = pdev->irq;
@@ -355,13 +353,6 @@ netxen_nic_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
         /* initialize the adapter */
         netxen_initialize_adapter_hw(adapter);
 
-#ifdef CONFIG_PPC
-        if ((adapter->ahw.boardcfg.board_type ==
-                NETXEN_BRDTYPE_P2_SB31_10G_IMEZ) &&
-                        (pci_func_id == 2))
-                    goto err_out_free_adapter;
-#endif /* CONFIG_PPC */
-
         /*
          *  Adapter in our case is quad port so initialize it before
          *  initializing the ports
@@ -509,16 +500,22 @@ netxen_nic_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
                                         NETXEN_CAM_RAM(0x1fc)));
                 if (val == 0x55555555) {
                     /* This is the first boot after power up */
+                    netxen_nic_read_w0(adapter, NETXEN_PCIE_REG(0x4), &val);
+                    if (!(val & 0x4)) {
+                        val |= 0x4;
+                        netxen_nic_write_w0(adapter, NETXEN_PCIE_REG(0x4), val);
+                        netxen_nic_read_w0(adapter, NETXEN_PCIE_REG(0x4), &val);
+                    }
                     val = readl(NETXEN_CRB_NORMALIZE(adapter,
                                         NETXEN_ROMUSB_GLB_SW_RESET));
                     printk(KERN_INFO"NetXen: read 0x%08x for reset reg.\n",val);
                     if (val != 0x80000f) {
                         /* clear the register for future unloads/loads */
-                        writel(0, NETXEN_CRB_NORMALIZE(adapter,
-                                                NETXEN_CAM_RAM(0x1fc)));
-                        printk(KERN_ERR "ERROR in NetXen HW init sequence.\n");
-                        err = -ENODEV;
-                        goto err_out_free_dev;
+                                writel(0, NETXEN_CRB_NORMALIZE(adapter,
+                                                        NETXEN_CAM_RAM(0x1fc)));
+                                printk(KERN_ERR "ERROR in NetXen HW init sequence.\n");
+                                err = -ENODEV;
+                                goto err_out_free_dev;
                     }
 
                     /* clear the register for future unloads/loads */