1 files changed, 77 insertions, 0 deletions

diff --git a/drivers/net/fddi/Kconfig b/drivers/net/fddi/Kconfig
new file mode 100644
index 000000000000..3a424c864f4d
--- /dev/null
+++ b/drivers/net/fddi/Kconfig
@@ -0,0 +1,77 @@
+#
+# FDDI network device configuration
+#
+
+config FDDI
+        tristate "FDDI driver support"
+        depends on PCI || EISA || TC
+        ---help---
+          Fiber Distributed Data Interface is a high speed local area network
+          design; essentially a replacement for high speed Ethernet. FDDI can
+          run over copper or fiber. If you are connected to such a network and
+          want a driver for the FDDI card in your computer, say Y here (and
+          then also Y to the driver for your FDDI card, below). Most people
+          will say N.
+
+if FDDI
+
+config DEFXX
+        tristate "Digital DEFTA/DEFEA/DEFPA adapter support"
+        depends on FDDI && (PCI || EISA || TC)
+        ---help---
+          This is support for the DIGITAL series of TURBOchannel (DEFTA),
+          EISA (DEFEA) and PCI (DEFPA) controllers which can connect you
+          to a local FDDI network.
+
+          To compile this driver as a module, choose M here: the module
+          will be called defxx.  If unsure, say N.
+
+config DEFXX_MMIO
+        bool
+        prompt "Use MMIO instead of PIO" if PCI || EISA
+        depends on DEFXX
+        default n if PCI || EISA
+        default y
+        ---help---
+          This instructs the driver to use EISA or PCI memory-mapped I/O
+          (MMIO) as appropriate instead of programmed I/O ports (PIO).
+          Enabling this gives an improvement in processing time in parts
+          of the driver, but it may cause problems with EISA (DEFEA)
+          adapters.  TURBOchannel does not have the concept of I/O ports,
+          so MMIO is always used for these (DEFTA) adapters.
+
+          If unsure, say N.
+
+config SKFP
+        tristate "SysKonnect FDDI PCI support"
+        depends on FDDI && PCI
+        select BITREVERSE
+        ---help---
+          Say Y here if you have a SysKonnect FDDI PCI adapter.
+          The following adapters are supported by this driver:
+          - SK-5521 (SK-NET FDDI-UP)
+          - SK-5522 (SK-NET FDDI-UP DAS)
+          - SK-5541 (SK-NET FDDI-FP)
+          - SK-5543 (SK-NET FDDI-LP)
+          - SK-5544 (SK-NET FDDI-LP DAS)
+          - SK-5821 (SK-NET FDDI-UP64)
+          - SK-5822 (SK-NET FDDI-UP64 DAS)
+          - SK-5841 (SK-NET FDDI-FP64)
+          - SK-5843 (SK-NET FDDI-LP64)
+          - SK-5844 (SK-NET FDDI-LP64 DAS)
+          - Netelligent 100 FDDI DAS Fibre SC
+          - Netelligent 100 FDDI SAS Fibre SC
+          - Netelligent 100 FDDI DAS UTP
+          - Netelligent 100 FDDI SAS UTP
+          - Netelligent 100 FDDI SAS Fibre MIC
+
+          Read <file:Documentation/networking/skfp.txt> for information about
+          the driver.
+
+          Questions concerning this driver can be addressed to:
+          <linux@syskonnect.de>
+
+          To compile this driver as a module, choose M here: the module
+          will be called skfp.  This is recommended.
+
+endif # FDDI