1 files changed, 29 insertions, 12 deletions

diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c
index 0687c6aa4e46..a1a5a6f15a65 100644
--- a/drivers/net/e1000e/netdev.c
+++ b/drivers/net/e1000e/netdev.c
@@ -2769,25 +2769,38 @@ void e1000e_reset(struct e1000_adapter *adapter)
         /*
          * flow control settings
          *
-         * The high water mark must be low enough to fit two full frame
+         * The high water mark must be low enough to fit one full frame
          * (or the size used for early receive) above it in the Rx FIFO.
          * Set it to the lower of:
          * - 90% of the Rx FIFO size, and
          * - the full Rx FIFO size minus the early receive size (for parts
          *   with ERT support assuming ERT set to E1000_ERT_2048), or
-         * - the full Rx FIFO size minus two full frames
+         * - the full Rx FIFO size minus one full frame
          */
-        if ((adapter->flags & FLAG_HAS_ERT) &&
-            (adapter->netdev->mtu > ETH_DATA_LEN))
-                hwm = min(((pba << 10) * 9 / 10),
-                          ((pba << 10) - (E1000_ERT_2048 << 3)));
-        else
-                hwm = min(((pba << 10) * 9 / 10),
-                          ((pba << 10) - (2 * adapter->max_frame_size)));
+        if (hw->mac.type == e1000_pchlan) {
+                /*
+                 * Workaround PCH LOM adapter hangs with certain network
+                 * loads.  If hangs persist, try disabling Tx flow control.
+                 */
+                if (adapter->netdev->mtu > ETH_DATA_LEN) {
+                        fc->high_water = 0x3500;
+                        fc->low_water  = 0x1500;
+                } else {
+                        fc->high_water = 0x5000;
+                        fc->low_water  = 0x3000;
+                }
+        } else {
+                if ((adapter->flags & FLAG_HAS_ERT) &&
+                    (adapter->netdev->mtu > ETH_DATA_LEN))
+                        hwm = min(((pba << 10) * 9 / 10),
+                                  ((pba << 10) - (E1000_ERT_2048 << 3)));
+                else
+                        hwm = min(((pba << 10) * 9 / 10),
+                                  ((pba << 10) - adapter->max_frame_size));
 
-        fc->high_water = hwm & E1000_FCRTH_RTH; /* 8-byte granularity */
-        fc->low_water = (fc->high_water - (2 * adapter->max_frame_size));
-        fc->low_water &= E1000_FCRTL_RTL; /* 8-byte granularity */
+                fc->high_water = hwm & E1000_FCRTH_RTH; /* 8-byte granularity */
+                fc->low_water = fc->high_water - 8;
+        }
 
         if (adapter->flags & FLAG_DISABLE_FC_PAUSE_TIME)
                 fc->pause_time = 0xFFFF;
@@ -2813,6 +2826,10 @@ void e1000e_reset(struct e1000_adapter *adapter)
         if (mac->ops.init_hw(hw))
                 e_err("Hardware Error\n");
 
+        /* additional part of the flow-control workaround above */
+        if (hw->mac.type == e1000_pchlan)
+                ew32(FCRTV_PCH, 0x1000);
+
         e1000_update_mng_vlan(adapter);
 
         /* Enable h/w to recognize an 802.1Q VLAN Ethernet packet */