5 files changed, 163 insertions, 87 deletions

diff --git a/drivers/net/e1000/e1000.h b/drivers/net/e1000/e1000.h
index 3f653a93e1bc..e02e9ba2e18b 100644
--- a/drivers/net/e1000/e1000.h
+++ b/drivers/net/e1000/e1000.h
@@ -188,11 +188,13 @@ struct e1000_tx_ring {
         /* array of buffer information structs */
         struct e1000_buffer *buffer_info;
 
-        struct e1000_buffer previous_buffer_info;
         spinlock_t tx_lock;
         uint16_t tdh;
         uint16_t tdt;
         uint64_t pkt;
+
+        boolean_t last_tx_tso;
+
 };
 
 struct e1000_rx_ring {
diff --git a/drivers/net/e1000/e1000_ethtool.c b/drivers/net/e1000/e1000_ethtool.c
index 8eae8ba27e84..c88f1a3c1b1d 100644
--- a/drivers/net/e1000/e1000_ethtool.c
+++ b/drivers/net/e1000/e1000_ethtool.c
@@ -562,10 +562,29 @@ e1000_get_drvinfo(struct net_device *netdev,
                        struct ethtool_drvinfo *drvinfo)
 {
         struct e1000_adapter *adapter = netdev_priv(netdev);
+        char firmware_version[32];
+        uint16_t eeprom_data;
 
         strncpy(drvinfo->driver,  e1000_driver_name, 32);
         strncpy(drvinfo->version, e1000_driver_version, 32);
-        strncpy(drvinfo->fw_version, "N/A", 32);
+        
+        /* EEPROM image version # is reported as firware version # for
+         * 8257{1|2|3} controllers */
+        e1000_read_eeprom(&adapter->hw, 5, 1, &eeprom_data);
+        switch (adapter->hw.mac_type) {
+        case e1000_82571:
+        case e1000_82572:
+        case e1000_82573:
+                sprintf(firmware_version, "%d.%d-%d", 
+                        (eeprom_data & 0xF000) >> 12,
+                        (eeprom_data & 0x0FF0) >> 4,
+                        eeprom_data & 0x000F);
+                break;
+        default:
+                sprintf(firmware_version, "n/a");
+        }
+
+        strncpy(drvinfo->fw_version, firmware_version, 32);
         strncpy(drvinfo->bus_info, pci_name(adapter->pdev), 32);
         drvinfo->n_stats = E1000_STATS_LEN;
         drvinfo->testinfo_len = E1000_TEST_LEN;
@@ -960,13 +979,21 @@ e1000_free_desc_rings(struct e1000_adapter *adapter)
                 }
         }
 
-        if(txdr->desc)
+        if(txdr->desc) {
                 pci_free_consistent(pdev, txdr->size, txdr->desc, txdr->dma);
-        if(rxdr->desc)
+                txdr->desc = NULL;
+        }
+        if(rxdr->desc) {
                 pci_free_consistent(pdev, rxdr->size, rxdr->desc, rxdr->dma);
+                rxdr->desc = NULL;
+        }
 
         kfree(txdr->buffer_info);
+        txdr->buffer_info = NULL;
+
         kfree(rxdr->buffer_info);
+        rxdr->buffer_info = NULL;
+
         return;
 }
 
@@ -1301,21 +1328,32 @@ static int
 e1000_setup_loopback_test(struct e1000_adapter *adapter)
 {
         uint32_t rctl;
+        struct e1000_hw *hw = &adapter->hw;
 
-        if(adapter->hw.media_type == e1000_media_type_fiber ||
-           adapter->hw.media_type == e1000_media_type_internal_serdes) {
-                if(adapter->hw.mac_type == e1000_82545 ||
-                   adapter->hw.mac_type == e1000_82546 ||
-                   adapter->hw.mac_type == e1000_82545_rev_3 ||
-                   adapter->hw.mac_type == e1000_82546_rev_3)
+        if (hw->media_type == e1000_media_type_fiber ||
+           hw->media_type == e1000_media_type_internal_serdes) {
+                switch (hw->mac_type) {
+                case e1000_82545:
+                case e1000_82546:
+                case e1000_82545_rev_3:
+                case e1000_82546_rev_3:
                         return e1000_set_phy_loopback(adapter);
-                else {
-                        rctl = E1000_READ_REG(&adapter->hw, RCTL);
+                        break;
+                case e1000_82571:
+                case e1000_82572:
+#define E1000_SERDES_LB_ON 0x410
+                        e1000_set_phy_loopback(adapter);
+                        E1000_WRITE_REG(hw, SCTL, E1000_SERDES_LB_ON);
+                        msec_delay(10);
+                        return 0;
+                        break;
+                default:
+                        rctl = E1000_READ_REG(hw, RCTL);
                         rctl |= E1000_RCTL_LBM_TCVR;
-                        E1000_WRITE_REG(&adapter->hw, RCTL, rctl);
+                        E1000_WRITE_REG(hw, RCTL, rctl);
                         return 0;
                 }
-        } else if(adapter->hw.media_type == e1000_media_type_copper)
+        } else if (hw->media_type == e1000_media_type_copper)
                 return e1000_set_phy_loopback(adapter);
 
         return 7;
@@ -1326,25 +1364,36 @@ e1000_loopback_cleanup(struct e1000_adapter *adapter)
 {
         uint32_t rctl;
         uint16_t phy_reg;
+        struct e1000_hw *hw = &adapter->hw;
 
         rctl = E1000_READ_REG(&adapter->hw, RCTL);
         rctl &= ~(E1000_RCTL_LBM_TCVR | E1000_RCTL_LBM_MAC);
         E1000_WRITE_REG(&adapter->hw, RCTL, rctl);
 
-        if(adapter->hw.media_type == e1000_media_type_copper ||
-           ((adapter->hw.media_type == e1000_media_type_fiber ||
-             adapter->hw.media_type == e1000_media_type_internal_serdes) &&
-            (adapter->hw.mac_type == e1000_82545 ||
-             adapter->hw.mac_type == e1000_82546 ||
-             adapter->hw.mac_type == e1000_82545_rev_3 ||
-             adapter->hw.mac_type == e1000_82546_rev_3))) {
-                adapter->hw.autoneg = TRUE;
-                e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &phy_reg);
-                if(phy_reg & MII_CR_LOOPBACK) {
+        switch (hw->mac_type) {
+        case e1000_82571:
+        case e1000_82572:
+                if (hw->media_type == e1000_media_type_fiber ||
+                   hw->media_type == e1000_media_type_internal_serdes){
+#define E1000_SERDES_LB_OFF 0x400
+                        E1000_WRITE_REG(hw, SCTL, E1000_SERDES_LB_OFF);
+                        msec_delay(10);
+                        break;
+                }
+                /* fall thru for Cu adapters */
+        case e1000_82545:
+        case e1000_82546:
+        case e1000_82545_rev_3:
+        case e1000_82546_rev_3:
+        default:
+                hw->autoneg = TRUE;
+                e1000_read_phy_reg(hw, PHY_CTRL, &phy_reg);
+                if (phy_reg & MII_CR_LOOPBACK) {
                         phy_reg &= ~MII_CR_LOOPBACK;
-                        e1000_write_phy_reg(&adapter->hw, PHY_CTRL, phy_reg);
-                        e1000_phy_reset(&adapter->hw);
+                        e1000_write_phy_reg(hw, PHY_CTRL, phy_reg);
+                        e1000_phy_reset(hw);
                 }
+                break;
         }
 }
 
@@ -1440,9 +1489,11 @@ static int
 e1000_loopback_test(struct e1000_adapter *adapter, uint64_t *data)
 {
         if((*data = e1000_setup_desc_rings(adapter))) goto err_loopback;
-        if((*data = e1000_setup_loopback_test(adapter))) goto err_loopback;
+        if((*data = e1000_setup_loopback_test(adapter)))
+                goto err_loopback_setup;
         *data = e1000_run_loopback_test(adapter);
         e1000_loopback_cleanup(adapter);
+err_loopback_setup:
         e1000_free_desc_rings(adapter);
 err_loopback:
         return *data;
@@ -1671,6 +1722,14 @@ e1000_phys_id(struct net_device *netdev, uint32_t data)
                 msleep_interruptible(data * 1000);
                 del_timer_sync(&adapter->blink_timer);
         }
+        else if(adapter->hw.mac_type < e1000_82573) {
+                E1000_WRITE_REG(&adapter->hw, LEDCTL, (E1000_LEDCTL_LED2_BLINK_RATE |
+                        E1000_LEDCTL_LED0_BLINK | E1000_LEDCTL_LED2_BLINK |
+                        (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED2_MODE_SHIFT) |
+                        (E1000_LEDCTL_MODE_LINK_ACTIVITY << E1000_LEDCTL_LED0_MODE_SHIFT) |
+                        (E1000_LEDCTL_MODE_LED_OFF << E1000_LEDCTL_LED1_MODE_SHIFT)));
+                msleep_interruptible(data * 1000);
+        }
         else {
                 E1000_WRITE_REG(&adapter->hw, LEDCTL, (E1000_LEDCTL_LED2_BLINK_RATE |
                         E1000_LEDCTL_LED1_BLINK | E1000_LEDCTL_LED2_BLINK | 
diff --git a/drivers/net/e1000/e1000_hw.c b/drivers/net/e1000/e1000_hw.c
index a267c5235fc0..136fc031e4ad 100644
--- a/drivers/net/e1000/e1000_hw.c
+++ b/drivers/net/e1000/e1000_hw.c
@@ -563,11 +563,13 @@ e1000_reset_hw(struct e1000_hw *hw)
             msec_delay(20);
             break;
         case e1000_82573:
-            udelay(10);
-            ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
-            ctrl_ext |= E1000_CTRL_EXT_EE_RST;
-            E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
-            E1000_WRITE_FLUSH(hw);
+            if (e1000_is_onboard_nvm_eeprom(hw) == FALSE) {
+                udelay(10);
+                ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
+                ctrl_ext |= E1000_CTRL_EXT_EE_RST;
+                E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
+                E1000_WRITE_FLUSH(hw);
+            }
             /* fall through */
         case e1000_82571:
         case e1000_82572:
@@ -844,19 +846,27 @@ e1000_setup_link(struct e1000_hw *hw)
      * control setting, then the variable hw->fc will
      * be initialized based on a value in the EEPROM.
      */
-    if(e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data)) {
-        DEBUGOUT("EEPROM Read Error\n");
-        return -E1000_ERR_EEPROM;
-    }
-
-    if(hw->fc == e1000_fc_default) {
-        if((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0)
-            hw->fc = e1000_fc_none;
-        else if((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) ==
-                EEPROM_WORD0F_ASM_DIR)
-            hw->fc = e1000_fc_tx_pause;
-        else
+    if (hw->fc == e1000_fc_default) {
+        switch (hw->mac_type) {
+        case e1000_82573:
             hw->fc = e1000_fc_full;
+            break;
+        default:
+            ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG,
+                                        1, &eeprom_data);
+            if (ret_val) {
+                DEBUGOUT("EEPROM Read Error\n");
+                return -E1000_ERR_EEPROM;
+            }
+            if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0)
+                hw->fc = e1000_fc_none;
+            else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) ==
+                    EEPROM_WORD0F_ASM_DIR)
+                hw->fc = e1000_fc_tx_pause;
+            else
+                hw->fc = e1000_fc_full;
+            break;
+        }
     }
 
     /* We want to save off the original Flow Control configuration just
@@ -2962,13 +2972,22 @@ e1000_phy_hw_reset(struct e1000_hw *hw)
     if(hw->mac_type > e1000_82543) {
         /* Read the device control register and assert the E1000_CTRL_PHY_RST
          * bit. Then, take it out of reset.
+         * For pre-e1000_82571 hardware, we delay for 10ms between the assert 
+         * and deassert.  For e1000_82571 hardware and later, we instead delay
+         * for 10ms after the deassertion.
          */
         ctrl = E1000_READ_REG(hw, CTRL);
         E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PHY_RST);
         E1000_WRITE_FLUSH(hw);
-        msec_delay(10);
+        
+        if (hw->mac_type < e1000_82571) 
+            msec_delay(10);
+        
         E1000_WRITE_REG(hw, CTRL, ctrl);
         E1000_WRITE_FLUSH(hw);
+        
+        if (hw->mac_type >= e1000_82571)
+            msec_delay(10);
     } else {
         /* Read the Extended Device Control Register, assert the PHY_RESET_DIR
          * bit to put the PHY into reset. Then, take it out of reset.
@@ -5278,11 +5297,15 @@ e1000_get_bus_info(struct e1000_hw *hw)
         hw->bus_speed = e1000_bus_speed_unknown;
         hw->bus_width = e1000_bus_width_unknown;
         break;
-    case e1000_82571:
     case e1000_82572:
     case e1000_82573:
         hw->bus_type = e1000_bus_type_pci_express;
         hw->bus_speed = e1000_bus_speed_2500;
+        hw->bus_width = e1000_bus_width_pciex_1;
+        break;
+    case e1000_82571:
+        hw->bus_type = e1000_bus_type_pci_express;
+        hw->bus_speed = e1000_bus_speed_2500;
         hw->bus_width = e1000_bus_width_pciex_4;
         break;
     default:
@@ -6650,6 +6673,12 @@ e1000_get_auto_rd_done(struct e1000_hw *hw)
         break;
     }
 
+    /* PHY configuration from NVM just starts after EECD_AUTO_RD sets to high.
+     * Need to wait for PHY configuration completion before accessing NVM
+     * and PHY. */
+    if (hw->mac_type == e1000_82573)
+        msec_delay(25);
+
     return E1000_SUCCESS;
 }
 
diff --git a/drivers/net/e1000/e1000_hw.h b/drivers/net/e1000/e1000_hw.h
index 76ce12809a11..7caa35748cea 100644
--- a/drivers/net/e1000/e1000_hw.h
+++ b/drivers/net/e1000/e1000_hw.h
@@ -123,6 +123,7 @@ typedef enum {
     e1000_bus_width_32,
     e1000_bus_width_64,
     e1000_bus_width_pciex_1,
+    e1000_bus_width_pciex_2,
     e1000_bus_width_pciex_4,
     e1000_bus_width_reserved
 } e1000_bus_width;
@@ -149,6 +150,7 @@ typedef enum {
     e1000_igp_cable_length_90  = 90,
     e1000_igp_cable_length_100 = 100,
     e1000_igp_cable_length_110 = 110,
+    e1000_igp_cable_length_115 = 115,
     e1000_igp_cable_length_120 = 120,
     e1000_igp_cable_length_130 = 130,
     e1000_igp_cable_length_140 = 140,
@@ -1457,6 +1459,7 @@ struct e1000_hw {
 #define E1000_EECD_AUPDEN    0x00100000 /* Enable Autonomous FLASH update */
 #define E1000_EECD_SHADV     0x00200000 /* Shadow RAM Data Valid */
 #define E1000_EECD_SEC1VAL   0x00400000 /* Sector One Valid */
+#define E1000_EECD_SECVAL_SHIFT      22
 #define E1000_STM_OPCODE     0xDB00
 #define E1000_HICR_FW_RESET  0xC0
 
@@ -1951,7 +1954,6 @@ struct e1000_host_command_info {
 
 #define E1000_MDALIGN          4096
 
-#define E1000_GCR_BEM32                 0x00400000
 #define E1000_GCR_L1_ACT_WITHOUT_L0S_RX 0x08000000
 /* Function Active and Power State to MNG */
 #define E1000_FACTPS_FUNC0_POWER_STATE_MASK         0x00000003
diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c
index e0ae248b4313..438a931fd55d 100644
--- a/drivers/net/e1000/e1000_main.c
+++ b/drivers/net/e1000/e1000_main.c
@@ -711,6 +711,7 @@ e1000_probe(struct pci_dev *pdev,
                 break;
         case e1000_82546:
         case e1000_82546_rev_3:
+        case e1000_82571:
                 if((E1000_READ_REG(&adapter->hw, STATUS) & E1000_STATUS_FUNC_1)
                    && (adapter->hw.media_type == e1000_media_type_copper)) {
                         e1000_read_eeprom(&adapter->hw,
@@ -1158,7 +1159,6 @@ e1000_setup_tx_resources(struct e1000_adapter *adapter,
                 return -ENOMEM;
         }
         memset(txdr->buffer_info, 0, size);
-        memset(&txdr->previous_buffer_info, 0, sizeof(struct e1000_buffer));
 
         /* round up to nearest 4K */
 
@@ -1813,11 +1813,6 @@ e1000_clean_tx_ring(struct e1000_adapter *adapter,
 
         /* Free all the Tx ring sk_buffs */
 
-        if (likely(tx_ring->previous_buffer_info.skb != NULL)) {
-                e1000_unmap_and_free_tx_resource(adapter,
-                                &tx_ring->previous_buffer_info);
-        }
-
         for(i = 0; i < tx_ring->count; i++) {
                 buffer_info = &tx_ring->buffer_info[i];
                 e1000_unmap_and_free_tx_resource(adapter, buffer_info);
@@ -1832,6 +1827,7 @@ e1000_clean_tx_ring(struct e1000_adapter *adapter,
 
         tx_ring->next_to_use = 0;
         tx_ring->next_to_clean = 0;
+        tx_ring->last_tx_tso = 0;
 
         writel(0, adapter->hw.hw_addr + tx_ring->tdh);
         writel(0, adapter->hw.hw_addr + tx_ring->tdt);
@@ -2437,6 +2433,16 @@ e1000_tx_map(struct e1000_adapter *adapter, struct e1000_tx_ring *tx_ring,
                 buffer_info = &tx_ring->buffer_info[i];
                 size = min(len, max_per_txd);
 #ifdef NETIF_F_TSO
+                /* Workaround for Controller erratum --
+                 * descriptor for non-tso packet in a linear SKB that follows a
+                 * tso gets written back prematurely before the data is fully
+                 * DMAd to the controller */
+                if (!skb->data_len && tx_ring->last_tx_tso &&
+                                !skb_shinfo(skb)->tso_size) {
+                        tx_ring->last_tx_tso = 0;
+                        size -= 4;
+                }
+
                 /* Workaround for premature desc write-backs
                  * in TSO mode.  Append 4-byte sentinel desc */
                 if(unlikely(mss && !nr_frags && size == len && size > 8))
@@ -2693,6 +2699,14 @@ e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
         if(skb->ip_summed == CHECKSUM_HW)
                 count++;
 #endif
+
+#ifdef NETIF_F_TSO
+        /* Controller Erratum workaround */
+        if (!skb->data_len && tx_ring->last_tx_tso &&
+                !skb_shinfo(skb)->tso_size)
+                count++;
+#endif
+
         count += TXD_USE_COUNT(len, max_txd_pwr);
 
         if(adapter->pcix_82544)
@@ -2774,9 +2788,10 @@ e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
                 return NETDEV_TX_OK;
         }
 
-        if (likely(tso))
+        if (likely(tso)) {
+                tx_ring->last_tx_tso = 1;
                 tx_flags |= E1000_TX_FLAGS_TSO;
-        else if (likely(e1000_tx_csum(adapter, tx_ring, skb)))
+        } else if (likely(e1000_tx_csum(adapter, tx_ring, skb)))
                 tx_flags |= E1000_TX_FLAGS_CSUM;
 
         /* Old method was to assume IPv4 packet by default if TSO was enabled.
@@ -3227,37 +3242,12 @@ e1000_clean_tx_irq(struct e1000_adapter *adapter,
         eop_desc = E1000_TX_DESC(*tx_ring, eop);
 
         while (eop_desc->upper.data & cpu_to_le32(E1000_TXD_STAT_DD)) {
-                /* Premature writeback of Tx descriptors clear (free buffers
-                 * and unmap pci_mapping) previous_buffer_info */
-                if (likely(tx_ring->previous_buffer_info.skb != NULL)) {
-                        e1000_unmap_and_free_tx_resource(adapter,
-                                        &tx_ring->previous_buffer_info);
-                }
-
                 for(cleaned = FALSE; !cleaned; ) {
                         tx_desc = E1000_TX_DESC(*tx_ring, i);
                         buffer_info = &tx_ring->buffer_info[i];
                         cleaned = (i == eop);
 
-#ifdef NETIF_F_TSO
-                        if (!(netdev->features & NETIF_F_TSO)) {
-#endif
-                                e1000_unmap_and_free_tx_resource(adapter,
-                                                                 buffer_info);
-#ifdef NETIF_F_TSO
-                        } else {
-                                if (cleaned) {
-                                        memcpy(&tx_ring->previous_buffer_info,
-                                               buffer_info,
-                                               sizeof(struct e1000_buffer));
-                                        memset(buffer_info, 0,
-                                               sizeof(struct e1000_buffer));
-                                } else {
-                                        e1000_unmap_and_free_tx_resource(
-                                            adapter, buffer_info);
-                                }
-                        }
-#endif
+                        e1000_unmap_and_free_tx_resource(adapter, buffer_info);
 
                         tx_desc->buffer_addr = 0;
                         tx_desc->lower.data = 0;
@@ -3318,12 +3308,6 @@ e1000_clean_tx_irq(struct e1000_adapter *adapter,
                         netif_stop_queue(netdev);
                 }
         }
-#ifdef NETIF_F_TSO
-        if (unlikely(!(eop_desc->upper.data & cpu_to_le32(E1000_TXD_STAT_DD)) &&
-            time_after(jiffies, tx_ring->previous_buffer_info.time_stamp + HZ)))
-                e1000_unmap_and_free_tx_resource(
-                    adapter, &tx_ring->previous_buffer_info);
-#endif
         return cleaned;
 }