1 files changed, 720 insertions, 0 deletions

diff --git a/drivers/net/atlx/atl1_hw.c b/drivers/net/atlx/atl1_hw.c
new file mode 100644
index 000000000000..9d3bd22e3a82
--- /dev/null
+++ b/drivers/net/atlx/atl1_hw.c
@@ -0,0 +1,720 @@
+/*
+ * Copyright(c) 2005 - 2006 Attansic Corporation. All rights reserved.
+ * Copyright(c) 2006 Chris Snook <csnook@redhat.com>
+ * Copyright(c) 2006 Jay Cliburn <jcliburn@gmail.com>
+ *
+ * Derived from Intel e1000 driver
+ * Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc., 59
+ * Temple Place - Suite 330, Boston, MA  02111-1307, USA.
+ */
+
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <linux/if_vlan.h>
+#include <linux/etherdevice.h>
+#include <linux/crc32.h>
+#include <asm/byteorder.h>
+
+#include "atl1.h"
+
+/*
+ * Reset the transmit and receive units; mask and clear all interrupts.
+ * hw - Struct containing variables accessed by shared code
+ * return : ATL1_SUCCESS  or  idle status (if error)
+ */
+s32 atl1_reset_hw(struct atl1_hw *hw)
+{
+        struct pci_dev *pdev = hw->back->pdev;
+        u32 icr;
+        int i;
+
+        /*
+         * Clear Interrupt mask to stop board from generating
+         * interrupts & Clear any pending interrupt events
+         */
+        /*
+         * iowrite32(0, hw->hw_addr + REG_IMR);
+         * iowrite32(0xffffffff, hw->hw_addr + REG_ISR);
+         */
+
+        /*
+         * Issue Soft Reset to the MAC.  This will reset the chip's
+         * transmit, receive, DMA.  It will not effect
+         * the current PCI configuration.  The global reset bit is self-
+         * clearing, and should clear within a microsecond.
+         */
+        iowrite32(MASTER_CTRL_SOFT_RST, hw->hw_addr + REG_MASTER_CTRL);
+        ioread32(hw->hw_addr + REG_MASTER_CTRL);
+
+        iowrite16(1, hw->hw_addr + REG_GPHY_ENABLE);
+        ioread16(hw->hw_addr + REG_GPHY_ENABLE);
+
+        msleep(1);              /* delay about 1ms */
+
+        /* Wait at least 10ms for All module to be Idle */
+        for (i = 0; i < 10; i++) {
+                icr = ioread32(hw->hw_addr + REG_IDLE_STATUS);
+                if (!icr)
+                        break;
+                msleep(1);      /* delay 1 ms */
+                cpu_relax();    /* FIXME: is this still the right way to do this? */
+        }
+
+        if (icr) {
+                dev_dbg(&pdev->dev, "ICR = 0x%x\n", icr);
+                return icr;
+        }
+
+        return ATL1_SUCCESS;
+}
+
+/* function about EEPROM
+ *
+ * check_eeprom_exist
+ * return 0 if eeprom exist
+ */
+static int atl1_check_eeprom_exist(struct atl1_hw *hw)
+{
+        u32 value;
+        value = ioread32(hw->hw_addr + REG_SPI_FLASH_CTRL);
+        if (value & SPI_FLASH_CTRL_EN_VPD) {
+                value &= ~SPI_FLASH_CTRL_EN_VPD;
+                iowrite32(value, hw->hw_addr + REG_SPI_FLASH_CTRL);
+        }
+
+        value = ioread16(hw->hw_addr + REG_PCIE_CAP_LIST);
+        return ((value & 0xFF00) == 0x6C00) ? 0 : 1;
+}
+
+static bool atl1_read_eeprom(struct atl1_hw *hw, u32 offset, u32 *p_value)
+{
+        int i;
+        u32 control;
+
+        if (offset & 3)
+                return false;   /* address do not align */
+
+        iowrite32(0, hw->hw_addr + REG_VPD_DATA);
+        control = (offset & VPD_CAP_VPD_ADDR_MASK) << VPD_CAP_VPD_ADDR_SHIFT;
+        iowrite32(control, hw->hw_addr + REG_VPD_CAP);
+        ioread32(hw->hw_addr + REG_VPD_CAP);
+
+        for (i = 0; i < 10; i++) {
+                msleep(2);
+                control = ioread32(hw->hw_addr + REG_VPD_CAP);
+                if (control & VPD_CAP_VPD_FLAG)
+                        break;
+        }
+        if (control & VPD_CAP_VPD_FLAG) {
+                *p_value = ioread32(hw->hw_addr + REG_VPD_DATA);
+                return true;
+        }
+        return false;           /* timeout */
+}
+
+/*
+ * Reads the value from a PHY register
+ * hw - Struct containing variables accessed by shared code
+ * reg_addr - address of the PHY register to read
+ */
+s32 atl1_read_phy_reg(struct atl1_hw *hw, u16 reg_addr, u16 *phy_data)
+{
+        u32 val;
+        int i;
+
+        val = ((u32) (reg_addr & MDIO_REG_ADDR_MASK)) << MDIO_REG_ADDR_SHIFT |
+                MDIO_START | MDIO_SUP_PREAMBLE | MDIO_RW | MDIO_CLK_25_4 <<
+                MDIO_CLK_SEL_SHIFT;
+        iowrite32(val, hw->hw_addr + REG_MDIO_CTRL);
+        ioread32(hw->hw_addr + REG_MDIO_CTRL);
+
+        for (i = 0; i < MDIO_WAIT_TIMES; i++) {
+                udelay(2);
+                val = ioread32(hw->hw_addr + REG_MDIO_CTRL);
+                if (!(val & (MDIO_START | MDIO_BUSY)))
+                        break;
+        }
+        if (!(val & (MDIO_START | MDIO_BUSY))) {
+                *phy_data = (u16) val;
+                return ATL1_SUCCESS;
+        }
+        return ATL1_ERR_PHY;
+}
+
+#define CUSTOM_SPI_CS_SETUP     2
+#define CUSTOM_SPI_CLK_HI       2
+#define CUSTOM_SPI_CLK_LO       2
+#define CUSTOM_SPI_CS_HOLD      2
+#define CUSTOM_SPI_CS_HI        3
+
+static bool atl1_spi_read(struct atl1_hw *hw, u32 addr, u32 *buf)
+{
+        int i;
+        u32 value;
+
+        iowrite32(0, hw->hw_addr + REG_SPI_DATA);
+        iowrite32(addr, hw->hw_addr + REG_SPI_ADDR);
+
+        value = SPI_FLASH_CTRL_WAIT_READY |
+            (CUSTOM_SPI_CS_SETUP & SPI_FLASH_CTRL_CS_SETUP_MASK) <<
+            SPI_FLASH_CTRL_CS_SETUP_SHIFT | (CUSTOM_SPI_CLK_HI &
+                                             SPI_FLASH_CTRL_CLK_HI_MASK) <<
+            SPI_FLASH_CTRL_CLK_HI_SHIFT | (CUSTOM_SPI_CLK_LO &
+                                           SPI_FLASH_CTRL_CLK_LO_MASK) <<
+            SPI_FLASH_CTRL_CLK_LO_SHIFT | (CUSTOM_SPI_CS_HOLD &
+                                           SPI_FLASH_CTRL_CS_HOLD_MASK) <<
+            SPI_FLASH_CTRL_CS_HOLD_SHIFT | (CUSTOM_SPI_CS_HI &
+                                            SPI_FLASH_CTRL_CS_HI_MASK) <<
+            SPI_FLASH_CTRL_CS_HI_SHIFT | (1 & SPI_FLASH_CTRL_INS_MASK) <<
+            SPI_FLASH_CTRL_INS_SHIFT;
+
+        iowrite32(value, hw->hw_addr + REG_SPI_FLASH_CTRL);
+
+        value |= SPI_FLASH_CTRL_START;
+        iowrite32(value, hw->hw_addr + REG_SPI_FLASH_CTRL);
+        ioread32(hw->hw_addr + REG_SPI_FLASH_CTRL);
+
+        for (i = 0; i < 10; i++) {
+                msleep(1);      /* 1ms */
+                value = ioread32(hw->hw_addr + REG_SPI_FLASH_CTRL);
+                if (!(value & SPI_FLASH_CTRL_START))
+                        break;
+        }
+
+        if (value & SPI_FLASH_CTRL_START)
+                return false;
+
+        *buf = ioread32(hw->hw_addr + REG_SPI_DATA);
+
+        return true;
+}
+
+/*
+ * get_permanent_address
+ * return 0 if get valid mac address,
+ */
+static int atl1_get_permanent_address(struct atl1_hw *hw)
+{
+        u32 addr[2];
+        u32 i, control;
+        u16 reg;
+        u8 eth_addr[ETH_ALEN];
+        bool key_valid;
+
+        if (is_valid_ether_addr(hw->perm_mac_addr))
+                return 0;
+
+        /* init */
+        addr[0] = addr[1] = 0;
+
+        if (!atl1_check_eeprom_exist(hw)) {     /* eeprom exist */
+                reg = 0;
+                key_valid = false;
+                /* Read out all EEPROM content */
+                i = 0;
+                while (1) {
+                        if (atl1_read_eeprom(hw, i + 0x100, &control)) {
+                                if (key_valid) {
+                                        if (reg == REG_MAC_STA_ADDR)
+                                                addr[0] = control;
+                                        else if (reg == (REG_MAC_STA_ADDR + 4))
+                                                addr[1] = control;
+                                        key_valid = false;
+                                } else if ((control & 0xff) == 0x5A) {
+                                        key_valid = true;
+                                        reg = (u16) (control >> 16);
+                                } else
+                                        break;  /* assume data end while encount an invalid KEYWORD */
+                        } else
+                                break;  /* read error */
+                        i += 4;
+                }
+
+                *(u32 *) &eth_addr[2] = swab32(addr[0]);
+                *(u16 *) &eth_addr[0] = swab16(*(u16 *) &addr[1]);
+                if (is_valid_ether_addr(eth_addr)) {
+                        memcpy(hw->perm_mac_addr, eth_addr, ETH_ALEN);
+                        return 0;
+                }
+                return 1;
+        }
+
+        /* see if SPI FLAGS exist ? */
+        addr[0] = addr[1] = 0;
+        reg = 0;
+        key_valid = false;
+        i = 0;
+        while (1) {
+                if (atl1_spi_read(hw, i + 0x1f000, &control)) {
+                        if (key_valid) {
+                                if (reg == REG_MAC_STA_ADDR)
+                                        addr[0] = control;
+                                else if (reg == (REG_MAC_STA_ADDR + 4))
+                                        addr[1] = control;
+                                key_valid = false;
+                        } else if ((control & 0xff) == 0x5A) {
+                                key_valid = true;
+                                reg = (u16) (control >> 16);
+                        } else
+                                break;  /* data end */
+                } else
+                        break;  /* read error */
+                i += 4;
+        }
+
+        *(u32 *) &eth_addr[2] = swab32(addr[0]);
+        *(u16 *) &eth_addr[0] = swab16(*(u16 *) &addr[1]);
+        if (is_valid_ether_addr(eth_addr)) {
+                memcpy(hw->perm_mac_addr, eth_addr, ETH_ALEN);
+                return 0;
+        }
+
+        /*
+         * On some motherboards, the MAC address is written by the
+         * BIOS directly to the MAC register during POST, and is
+         * not stored in eeprom.  If all else thus far has failed
+         * to fetch the permanent MAC address, try reading it directly.
+         */
+        addr[0] = ioread32(hw->hw_addr + REG_MAC_STA_ADDR);
+        addr[1] = ioread16(hw->hw_addr + (REG_MAC_STA_ADDR + 4));
+        *(u32 *) &eth_addr[2] = swab32(addr[0]);
+        *(u16 *) &eth_addr[0] = swab16(*(u16 *) &addr[1]);
+        if (is_valid_ether_addr(eth_addr)) {
+                memcpy(hw->perm_mac_addr, eth_addr, ETH_ALEN);
+                return 0;
+        }
+
+        return 1;
+}
+
+/*
+ * Reads the adapter's MAC address from the EEPROM
+ * hw - Struct containing variables accessed by shared code
+ */
+s32 atl1_read_mac_addr(struct atl1_hw *hw)
+{
+        u16 i;
+
+        if (atl1_get_permanent_address(hw))
+                random_ether_addr(hw->perm_mac_addr);
+
+        for (i = 0; i < ETH_ALEN; i++)
+                hw->mac_addr[i] = hw->perm_mac_addr[i];
+        return ATL1_SUCCESS;
+}
+
+/*
+ * Hashes an address to determine its location in the multicast table
+ * hw - Struct containing variables accessed by shared code
+ * mc_addr - the multicast address to hash
+ *
+ * atl1_hash_mc_addr
+ *  purpose
+ *      set hash value for a multicast address
+ *      hash calcu processing :
+ *          1. calcu 32bit CRC for multicast address
+ *          2. reverse crc with MSB to LSB
+ */
+u32 atl1_hash_mc_addr(struct atl1_hw *hw, u8 *mc_addr)
+{
+        u32 crc32, value = 0;
+        int i;
+
+        crc32 = ether_crc_le(6, mc_addr);
+        for (i = 0; i < 32; i++)
+                value |= (((crc32 >> i) & 1) << (31 - i));
+
+        return value;
+}
+
+/*
+ * Sets the bit in the multicast table corresponding to the hash value.
+ * hw - Struct containing variables accessed by shared code
+ * hash_value - Multicast address hash value
+ */
+void atl1_hash_set(struct atl1_hw *hw, u32 hash_value)
+{
+        u32 hash_bit, hash_reg;
+        u32 mta;
+
+        /*
+         * The HASH Table  is a register array of 2 32-bit registers.
+         * It is treated like an array of 64 bits.  We want to set
+         * bit BitArray[hash_value]. So we figure out what register
+         * the bit is in, read it, OR in the new bit, then write
+         * back the new value.  The register is determined by the
+         * upper 7 bits of the hash value and the bit within that
+         * register are determined by the lower 5 bits of the value.
+         */
+        hash_reg = (hash_value >> 31) & 0x1;
+        hash_bit = (hash_value >> 26) & 0x1F;
+        mta = ioread32((hw->hw_addr + REG_RX_HASH_TABLE) + (hash_reg << 2));
+        mta |= (1 << hash_bit);
+        iowrite32(mta, (hw->hw_addr + REG_RX_HASH_TABLE) + (hash_reg << 2));
+}
+
+/*
+ * Writes a value to a PHY register
+ * hw - Struct containing variables accessed by shared code
+ * reg_addr - address of the PHY register to write
+ * data - data to write to the PHY
+ */
+s32 atl1_write_phy_reg(struct atl1_hw *hw, u32 reg_addr, u16 phy_data)
+{
+        int i;
+        u32 val;
+
+        val = ((u32) (phy_data & MDIO_DATA_MASK)) << MDIO_DATA_SHIFT |
+            (reg_addr & MDIO_REG_ADDR_MASK) << MDIO_REG_ADDR_SHIFT |
+            MDIO_SUP_PREAMBLE |
+            MDIO_START | MDIO_CLK_25_4 << MDIO_CLK_SEL_SHIFT;
+        iowrite32(val, hw->hw_addr + REG_MDIO_CTRL);
+        ioread32(hw->hw_addr + REG_MDIO_CTRL);
+
+        for (i = 0; i < MDIO_WAIT_TIMES; i++) {
+                udelay(2);
+                val = ioread32(hw->hw_addr + REG_MDIO_CTRL);
+                if (!(val & (MDIO_START | MDIO_BUSY)))
+                        break;
+        }
+
+        if (!(val & (MDIO_START | MDIO_BUSY)))
+                return ATL1_SUCCESS;
+
+        return ATL1_ERR_PHY;
+}
+
+/*
+ * Make L001's PHY out of Power Saving State (bug)
+ * hw - Struct containing variables accessed by shared code
+ * when power on, L001's PHY always on Power saving State
+ * (Gigabit Link forbidden)
+ */
+static s32 atl1_phy_leave_power_saving(struct atl1_hw *hw)
+{
+        s32 ret;
+        ret = atl1_write_phy_reg(hw, 29, 0x0029);
+        if (ret)
+                return ret;
+        return atl1_write_phy_reg(hw, 30, 0);
+}
+
+/*
+ *TODO: do something or get rid of this
+ */
+s32 atl1_phy_enter_power_saving(struct atl1_hw *hw)
+{
+/*    s32 ret_val;
+ *    u16 phy_data;
+ */
+
+/*
+    ret_val = atl1_write_phy_reg(hw, ...);
+    ret_val = atl1_write_phy_reg(hw, ...);
+    ....
+*/
+        return ATL1_SUCCESS;
+}
+
+/*
+ * Resets the PHY and make all config validate
+ * hw - Struct containing variables accessed by shared code
+ *
+ * Sets bit 15 and 12 of the MII Control regiser (for F001 bug)
+ */
+static s32 atl1_phy_reset(struct atl1_hw *hw)
+{
+        struct pci_dev *pdev = hw->back->pdev;
+        s32 ret_val;
+        u16 phy_data;
+
+        if (hw->media_type == MEDIA_TYPE_AUTO_SENSOR ||
+            hw->media_type == MEDIA_TYPE_1000M_FULL)
+                phy_data = MII_CR_RESET | MII_CR_AUTO_NEG_EN;
+        else {
+                switch (hw->media_type) {
+                case MEDIA_TYPE_100M_FULL:
+                        phy_data =
+                            MII_CR_FULL_DUPLEX | MII_CR_SPEED_100 |
+                            MII_CR_RESET;
+                        break;
+                case MEDIA_TYPE_100M_HALF:
+                        phy_data = MII_CR_SPEED_100 | MII_CR_RESET;
+                        break;
+                case MEDIA_TYPE_10M_FULL:
+                        phy_data =
+                            MII_CR_FULL_DUPLEX | MII_CR_SPEED_10 | MII_CR_RESET;
+                        break;
+                default:        /* MEDIA_TYPE_10M_HALF: */
+                        phy_data = MII_CR_SPEED_10 | MII_CR_RESET;
+                        break;
+                }
+        }
+
+        ret_val = atl1_write_phy_reg(hw, MII_BMCR, phy_data);
+        if (ret_val) {
+                u32 val;
+                int i;
+                /* pcie serdes link may be down! */
+                dev_dbg(&pdev->dev, "pcie phy link down\n");
+
+                for (i = 0; i < 25; i++) {
+                        msleep(1);
+                        val = ioread32(hw->hw_addr + REG_MDIO_CTRL);
+                        if (!(val & (MDIO_START | MDIO_BUSY)))
+                                break;
+                }
+
+                if ((val & (MDIO_START | MDIO_BUSY)) != 0) {
+                        dev_warn(&pdev->dev, "pcie link down at least 25ms\n");
+                        return ret_val;
+                }
+        }
+        return ATL1_SUCCESS;
+}
+
+/*
+ * Configures PHY autoneg and flow control advertisement settings
+ * hw - Struct containing variables accessed by shared code
+ */
+s32 atl1_phy_setup_autoneg_adv(struct atl1_hw *hw)
+{
+        s32 ret_val;
+        s16 mii_autoneg_adv_reg;
+        s16 mii_1000t_ctrl_reg;
+
+        /* Read the MII Auto-Neg Advertisement Register (Address 4). */
+        mii_autoneg_adv_reg = MII_AR_DEFAULT_CAP_MASK;
+
+        /* Read the MII 1000Base-T Control Register (Address 9). */
+        mii_1000t_ctrl_reg = MII_AT001_CR_1000T_DEFAULT_CAP_MASK;
+
+        /*
+         * First we clear all the 10/100 mb speed bits in the Auto-Neg
+         * Advertisement Register (Address 4) and the 1000 mb speed bits in
+         * the  1000Base-T Control Register (Address 9).
+         */
+        mii_autoneg_adv_reg &= ~MII_AR_SPEED_MASK;
+        mii_1000t_ctrl_reg &= ~MII_AT001_CR_1000T_SPEED_MASK;
+
+        /*
+         * Need to parse media_type  and set up
+         * the appropriate PHY registers.
+         */
+        switch (hw->media_type) {
+        case MEDIA_TYPE_AUTO_SENSOR:
+                mii_autoneg_adv_reg |= (MII_AR_10T_HD_CAPS |
+                                        MII_AR_10T_FD_CAPS |
+                                        MII_AR_100TX_HD_CAPS |
+                                        MII_AR_100TX_FD_CAPS);
+                mii_1000t_ctrl_reg |= MII_AT001_CR_1000T_FD_CAPS;
+                break;
+
+        case MEDIA_TYPE_1000M_FULL:
+                mii_1000t_ctrl_reg |= MII_AT001_CR_1000T_FD_CAPS;
+                break;
+
+        case MEDIA_TYPE_100M_FULL:
+                mii_autoneg_adv_reg |= MII_AR_100TX_FD_CAPS;
+                break;
+
+        case MEDIA_TYPE_100M_HALF:
+                mii_autoneg_adv_reg |= MII_AR_100TX_HD_CAPS;
+                break;
+
+        case MEDIA_TYPE_10M_FULL:
+                mii_autoneg_adv_reg |= MII_AR_10T_FD_CAPS;
+                break;
+
+        default:
+                mii_autoneg_adv_reg |= MII_AR_10T_HD_CAPS;
+                break;
+        }
+
+        /* flow control fixed to enable all */
+        mii_autoneg_adv_reg |= (MII_AR_ASM_DIR | MII_AR_PAUSE);
+
+        hw->mii_autoneg_adv_reg = mii_autoneg_adv_reg;
+        hw->mii_1000t_ctrl_reg = mii_1000t_ctrl_reg;
+
+        ret_val = atl1_write_phy_reg(hw, MII_ADVERTISE, mii_autoneg_adv_reg);
+        if (ret_val)
+                return ret_val;
+
+        ret_val = atl1_write_phy_reg(hw, MII_AT001_CR, mii_1000t_ctrl_reg);
+        if (ret_val)
+                return ret_val;
+
+        return ATL1_SUCCESS;
+}
+
+/*
+ * Configures link settings.
+ * hw - Struct containing variables accessed by shared code
+ * Assumes the hardware has previously been reset and the
+ * transmitter and receiver are not enabled.
+ */
+static s32 atl1_setup_link(struct atl1_hw *hw)
+{
+        struct pci_dev *pdev = hw->back->pdev;
+        s32 ret_val;
+
+        /*
+         * Options:
+         *  PHY will advertise value(s) parsed from
+         *  autoneg_advertised and fc
+         *  no matter what autoneg is , We will not wait link result.
+         */
+        ret_val = atl1_phy_setup_autoneg_adv(hw);
+        if (ret_val) {
+                dev_dbg(&pdev->dev, "error setting up autonegotiation\n");
+                return ret_val;
+        }
+        /* SW.Reset , En-Auto-Neg if needed */
+        ret_val = atl1_phy_reset(hw);
+        if (ret_val) {
+                dev_dbg(&pdev->dev, "error resetting phy\n");
+                return ret_val;
+        }
+        hw->phy_configured = true;
+        return ret_val;
+}
+
+static struct atl1_spi_flash_dev flash_table[] = {
+/*      MFR_NAME  WRSR  READ  PRGM  WREN  WRDI  RDSR  RDID  SECTOR_ERASE CHIP_ERASE */
+        {"Atmel", 0x00, 0x03, 0x02, 0x06, 0x04, 0x05, 0x15, 0x52,        0x62},
+        {"SST",   0x01, 0x03, 0x02, 0x06, 0x04, 0x05, 0x90, 0x20,        0x60},
+        {"ST",    0x01, 0x03, 0x02, 0x06, 0x04, 0x05, 0xAB, 0xD8,        0xC7},
+};
+
+static void atl1_init_flash_opcode(struct atl1_hw *hw)
+{
+        if (hw->flash_vendor >= ARRAY_SIZE(flash_table))
+                hw->flash_vendor = 0;   /* ATMEL */
+
+        /* Init OP table */
+        iowrite8(flash_table[hw->flash_vendor].cmd_program,
+                hw->hw_addr + REG_SPI_FLASH_OP_PROGRAM);
+        iowrite8(flash_table[hw->flash_vendor].cmd_sector_erase,
+                hw->hw_addr + REG_SPI_FLASH_OP_SC_ERASE);
+        iowrite8(flash_table[hw->flash_vendor].cmd_chip_erase,
+                hw->hw_addr + REG_SPI_FLASH_OP_CHIP_ERASE);
+        iowrite8(flash_table[hw->flash_vendor].cmd_rdid,
+                hw->hw_addr + REG_SPI_FLASH_OP_RDID);
+        iowrite8(flash_table[hw->flash_vendor].cmd_wren,
+                hw->hw_addr + REG_SPI_FLASH_OP_WREN);
+        iowrite8(flash_table[hw->flash_vendor].cmd_rdsr,
+                hw->hw_addr + REG_SPI_FLASH_OP_RDSR);
+        iowrite8(flash_table[hw->flash_vendor].cmd_wrsr,
+                hw->hw_addr + REG_SPI_FLASH_OP_WRSR);
+        iowrite8(flash_table[hw->flash_vendor].cmd_read,
+                hw->hw_addr + REG_SPI_FLASH_OP_READ);
+}
+
+/*
+ * Performs basic configuration of the adapter.
+ * hw - Struct containing variables accessed by shared code
+ * Assumes that the controller has previously been reset and is in a
+ * post-reset uninitialized state. Initializes multicast table,
+ * and  Calls routines to setup link
+ * Leaves the transmit and receive units disabled and uninitialized.
+ */
+s32 atl1_init_hw(struct atl1_hw *hw)
+{
+        u32 ret_val = 0;
+
+        /* Zero out the Multicast HASH table */
+        iowrite32(0, hw->hw_addr + REG_RX_HASH_TABLE);
+        /* clear the old settings from the multicast hash table */
+        iowrite32(0, (hw->hw_addr + REG_RX_HASH_TABLE) + (1 << 2));
+
+        atl1_init_flash_opcode(hw);
+
+        if (!hw->phy_configured) {
+                /* enable GPHY LinkChange Interrrupt */
+                ret_val = atl1_write_phy_reg(hw, 18, 0xC00);
+                if (ret_val)
+                        return ret_val;
+                /* make PHY out of power-saving state */
+                ret_val = atl1_phy_leave_power_saving(hw);
+                if (ret_val)
+                        return ret_val;
+                /* Call a subroutine to configure the link */
+                ret_val = atl1_setup_link(hw);
+        }
+        return ret_val;
+}
+
+/*
+ * Detects the current speed and duplex settings of the hardware.
+ * hw - Struct containing variables accessed by shared code
+ * speed - Speed of the connection
+ * duplex - Duplex setting of the connection
+ */
+s32 atl1_get_speed_and_duplex(struct atl1_hw *hw, u16 *speed, u16 *duplex)
+{
+        struct pci_dev *pdev = hw->back->pdev;
+        s32 ret_val;
+        u16 phy_data;
+
+        /* ; --- Read   PHY Specific Status Register (17) */
+        ret_val = atl1_read_phy_reg(hw, MII_AT001_PSSR, &phy_data);
+        if (ret_val)
+                return ret_val;
+
+        if (!(phy_data & MII_AT001_PSSR_SPD_DPLX_RESOLVED))
+                return ATL1_ERR_PHY_RES;
+
+        switch (phy_data & MII_AT001_PSSR_SPEED) {
+        case MII_AT001_PSSR_1000MBS:
+                *speed = SPEED_1000;
+                break;
+        case MII_AT001_PSSR_100MBS:
+                *speed = SPEED_100;
+                break;
+        case MII_AT001_PSSR_10MBS:
+                *speed = SPEED_10;
+                break;
+        default:
+                dev_dbg(&pdev->dev, "error getting speed\n");
+                return ATL1_ERR_PHY_SPEED;
+                break;
+        }
+        if (phy_data & MII_AT001_PSSR_DPLX)
+                *duplex = FULL_DUPLEX;
+        else
+                *duplex = HALF_DUPLEX;
+
+        return ATL1_SUCCESS;
+}
+
+void atl1_set_mac_addr(struct atl1_hw *hw)
+{
+        u32 value;
+        /*
+         * 00-0B-6A-F6-00-DC
+         * 0:  6AF600DC   1: 000B
+         * low dword
+         */
+        value = (((u32) hw->mac_addr[2]) << 24) |
+            (((u32) hw->mac_addr[3]) << 16) |
+            (((u32) hw->mac_addr[4]) << 8) | (((u32) hw->mac_addr[5]));
+        iowrite32(value, hw->hw_addr + REG_MAC_STA_ADDR);
+        /* high dword */
+        value = (((u32) hw->mac_addr[0]) << 8) | (((u32) hw->mac_addr[1]));
+        iowrite32(value, (hw->hw_addr + REG_MAC_STA_ADDR) + (1 << 2));
+}