3 files changed, 21 insertions, 6 deletions

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 84c103a7ee13..ff115d920888 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -55,14 +55,16 @@ static void mmci_set_clkreg(struct mmci_host *host, unsigned int desired)
                         host->cclk = host->mclk / (2 * (clk + 1));
                 }
                 if (host->hw_designer == AMBA_VENDOR_ST)
-                        clk |= MCI_FCEN; /* Bug fix in ST IP block */
+                        clk |= MCI_ST_FCEN; /* Bug fix in ST IP block */
                 clk |= MCI_CLK_ENABLE;
                 /* This hasn't proven to be worthwhile */
                 /* clk |= MCI_CLK_PWRSAVE; */
         }
 
         if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_4)
-                clk |= MCI_WIDE_BUS;
+                clk |= MCI_4BIT_BUS;
+        if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_8)
+                clk |= MCI_ST_8BIT_BUS;
 
         writel(clk, host->base + MMCICLOCK);
 }
@@ -629,7 +631,18 @@ static int __devinit mmci_probe(struct amba_device *dev, struct amba_id *id)
 
         mmc->ops = &mmci_ops;
         mmc->f_min = (host->mclk + 511) / 512;
-        mmc->f_max = min(host->mclk, fmax);
+        /*
+         * If the platform data supplies a maximum operating
+         * frequency, this takes precedence. Else, we fall back
+         * to using the module parameter, which has a (low)
+         * default value in case it is not specified. Either
+         * value must not exceed the clock rate into the block,
+         * of course.
+         */
+        if (plat->f_max)
+                mmc->f_max = min(host->mclk, plat->f_max);
+        else
+                mmc->f_max = min(host->mclk, fmax);
         dev_dbg(mmc_dev(mmc), "clocking block at %u Hz\n", mmc->f_max);
 
 #ifdef CONFIG_REGULATOR
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 1ceb9a90f59b..d77062e5e3af 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -25,9 +25,11 @@
 #define MCI_CLK_ENABLE          (1 << 8)
 #define MCI_CLK_PWRSAVE         (1 << 9)
 #define MCI_CLK_BYPASS          (1 << 10)
-#define MCI_WIDE_BUS            (1 << 11)
+#define MCI_4BIT_BUS            (1 << 11)
+/* 8bit wide buses supported in ST Micro versions */
+#define MCI_ST_8BIT_BUS         (1 << 12)
 /* HW flow control on the ST Micro version */
-#define MCI_FCEN                (1 << 13)
+#define MCI_ST_FCEN             (1 << 13)
 
 #define MMCIARGUMENT            0x008
 #define MMCICOMMAND             0x00c
diff --git a/drivers/mmc/host/pxamci.c b/drivers/mmc/host/pxamci.c
index 0ed48959b590..e4f00e70a749 100644
--- a/drivers/mmc/host/pxamci.c
+++ b/drivers/mmc/host/pxamci.c
@@ -544,7 +544,7 @@ static irqreturn_t pxamci_detect_irq(int irq, void *devid)
 {
         struct pxamci_host *host = mmc_priv(devid);
 
-        mmc_detect_change(devid, host->pdata->detect_delay);
+        mmc_detect_change(devid, msecs_to_jiffies(host->pdata->detect_delay_ms));
         return IRQ_HANDLED;
 }