1 files changed, 160 insertions, 0 deletions

diff --git a/drivers/media/video/cx18/cx18-dvb.c b/drivers/media/video/cx18/cx18-dvb.c
index 6ea3fe623ef4..51a0c33b25b7 100644
--- a/drivers/media/video/cx18/cx18-dvb.c
+++ b/drivers/media/video/cx18/cx18-dvb.c
@@ -30,6 +30,10 @@
 #include "s5h1409.h"
 #include "mxl5005s.h"
 #include "zl10353.h"
+
+#include <linux/firmware.h>
+#include "mt352.h"
+#include "mt352_priv.h"
 #include "tuner-xc2028.h"
 
 DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr);
@@ -38,6 +42,11 @@ DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr);
 #define CX18_CLOCK_ENABLE2               0xc71024
 #define CX18_DMUX_CLK_MASK               0x0080
 
+/*
+ * CX18_CARD_HVR_1600_ESMT
+ * CX18_CARD_HVR_1600_SAMSUNG
+ */
+
 static struct mxl5005s_config hauppauge_hvr1600_tuner = {
         .i2c_address     = 0xC6 >> 1,
         .if_freq         = IF_FREQ_5380000HZ,
@@ -65,6 +74,9 @@ static struct s5h1409_config hauppauge_hvr1600_config = {
         .mpeg_timing   = S5H1409_MPEGTIMING_CONTINOUS_NONINVERTING_CLOCK
 };
 
+/*
+ * CX18_CARD_LEADTEK_DVR3100H
+ */
 /* Information/confirmation of proper config values provided by Terry Wu */
 static struct zl10353_config leadtek_dvr3100h_demod = {
         .demod_address         = 0x1e >> 1, /* Datasheet suggested straps */
@@ -74,6 +86,121 @@ static struct zl10353_config leadtek_dvr3100h_demod = {
         .disable_i2c_gate_ctrl = 1,         /* Disable the I2C gate */
 };
 
+/*
+ * CX18_CARD_YUAN_MPC718
+ */
+/*
+ * Due to
+ *
+ * 1. an absence of information on how to prgram the MT352
+ * 2. the Linux mt352 module pushing MT352 initialzation off onto us here
+ *
+ * We have to use an init sequence that *you* must extract from the Windows
+ * driver (yuanrap.sys) and which we load as a firmware.
+ *
+ * If someone can provide me with a Zarlink MT352 (Intel CE6352?) Design Manual
+ * with chip programming details, then I can remove this annoyance.
+ */
+static int yuan_mpc718_mt352_reqfw(struct cx18_stream *stream,
+                                   const struct firmware **fw)
+{
+        struct cx18 *cx = stream->cx;
+        const char *fn = "dvb-cx18-mpc718-mt352.fw";
+        int ret;
+
+        ret = request_firmware(fw, fn, &cx->pci_dev->dev);
+        if (ret)
+                CX18_ERR("Unable to open firmware file %s\n", fn);
+        else {
+                size_t sz = (*fw)->size;
+                if (sz < 2 || sz > 64 || (sz % 2) != 0) {
+                        CX18_ERR("Firmware %s has a bad size: %lu bytes\n",
+                                 fn, (unsigned long) sz);
+                        ret = -EILSEQ;
+                        release_firmware(*fw);
+                        *fw = NULL;
+                }
+        }
+
+        if (ret) {
+                CX18_ERR("The MPC718 board variant with the MT352 DVB-T"
+                          "demodualtor will not work without it\n");
+                CX18_ERR("Run 'linux/Documentation/dvb/get_dvb_firmware "
+                          "mpc718' if you need the firmware\n");
+        }
+        return ret;
+}
+
+static int yuan_mpc718_mt352_init(struct dvb_frontend *fe)
+{
+        struct cx18_dvb *dvb = container_of(fe->dvb,
+                                            struct cx18_dvb, dvb_adapter);
+        struct cx18_stream *stream = container_of(dvb, struct cx18_stream, dvb);
+        const struct firmware *fw = NULL;
+        int ret;
+        int i;
+        u8 buf[3];
+
+        ret = yuan_mpc718_mt352_reqfw(stream, &fw);
+        if (ret)
+                return ret;
+
+        /* Loop through all the register-value pairs in the firmware file */
+        for (i = 0; i < fw->size; i += 2) {
+                buf[0] = fw->data[i];
+                /* Intercept a few registers we want to set ourselves */
+                switch (buf[0]) {
+                case TRL_NOMINAL_RATE_0:
+                        /* Set our custom OFDM bandwidth in the case below */
+                        break;
+                case TRL_NOMINAL_RATE_1:
+                        /* 6 MHz: 64/7 * 6/8 / 20.48 * 2^16 = 0x55b6.db6 */
+                        /* 7 MHz: 64/7 * 7/8 / 20.48 * 2^16 = 0x6400 */
+                        /* 8 MHz: 64/7 * 8/8 / 20.48 * 2^16 = 0x7249.249 */
+                        buf[1] = 0x72;
+                        buf[2] = 0x49;
+                        mt352_write(fe, buf, 3);
+                        break;
+                case INPUT_FREQ_0:
+                        /* Set our custom IF in the case below */
+                        break;
+                case INPUT_FREQ_1:
+                        /* 4.56 MHz IF: (20.48 - 4.56)/20.48 * 2^14 = 0x31c0 */
+                        buf[1] = 0x31;
+                        buf[2] = 0xc0;
+                        mt352_write(fe, buf, 3);
+                        break;
+                default:
+                        /* Pass through the register-value pair from the fw */
+                        buf[1] = fw->data[i+1];
+                        mt352_write(fe, buf, 2);
+                        break;
+                }
+        }
+
+        buf[0] = (u8) TUNER_GO;
+        buf[1] = 0x01; /* Go */
+        mt352_write(fe, buf, 2);
+        release_firmware(fw);
+        return 0;
+}
+
+static struct mt352_config yuan_mpc718_mt352_demod = {
+        .demod_address = 0x1e >> 1,
+        .adc_clock     = 20480,     /* 20.480 MHz */
+        .if2           =  4560,     /*  4.560 MHz */
+        .no_tuner      = 1,         /* XC3028 is not behind the gate */
+        .demod_init    = yuan_mpc718_mt352_init,
+};
+
+static struct zl10353_config yuan_mpc718_zl10353_demod = {
+        .demod_address         = 0x1e >> 1, /* Datasheet suggested straps */
+        .if2                   = 45600,     /* 4.560 MHz IF from the XC3028 */
+        .parallel_ts           = 1,         /* Not a serial TS */
+        .no_tuner              = 1,         /* XC3028 is not behind the gate */
+        .disable_i2c_gate_ctrl = 1,         /* Disable the I2C gate */
+};
+
 static int dvb_register(struct cx18_stream *stream);
 
 /* Kernel DVB framework calls this when the feed needs to start.
@@ -113,6 +240,7 @@ static int cx18_dvb_start_feed(struct dvb_demux_feed *feed)
                 break;
 
         case CX18_CARD_LEADTEK_DVR3100H:
+        case CX18_CARD_YUAN_MPC718:
         default:
                 /* Assumption - Parallel transport - Signalling
                  * undefined or default.
@@ -326,6 +454,38 @@ static int dvb_register(struct cx18_stream *stream)
                                 fe->ops.tuner_ops.set_config(fe, &ctrl);
                 }
                 break;
+        case CX18_CARD_YUAN_MPC718:
+                /*
+                 * TODO
+                 * Apparently, these cards also could instead have a
+                 * DiBcom demod supported by one of the db7000 drivers
+                 */
+                dvb->fe = dvb_attach(mt352_attach,
+                                     &yuan_mpc718_mt352_demod,
+                                     &cx->i2c_adap[1]);
+                if (dvb->fe == NULL)
+                        dvb->fe = dvb_attach(zl10353_attach,
+                                             &yuan_mpc718_zl10353_demod,
+                                             &cx->i2c_adap[1]);
+                if (dvb->fe != NULL) {
+                        struct dvb_frontend *fe;
+                        struct xc2028_config cfg = {
+                                .i2c_adap = &cx->i2c_adap[1],
+                                .i2c_addr = 0xc2 >> 1,
+                                .ctrl = NULL,
+                        };
+                        static struct xc2028_ctrl ctrl = {
+                                .fname   = XC2028_DEFAULT_FIRMWARE,
+                                .max_len = 64,
+                                .demod   = XC3028_FE_ZARLINK456,
+                                .type    = XC2028_AUTO,
+                        };
+
+                        fe = dvb_attach(xc2028_attach, dvb->fe, &cfg);
+                        if (fe != NULL && fe->ops.tuner_ops.set_config != NULL)
+                                fe->ops.tuner_ops.set_config(fe, &ctrl);
+                }
+                break;
         default:
                 /* No Digital Tv Support */
                 break;