1 files changed, 60 insertions, 17 deletions

diff --git a/drivers/media/common/tuners/tuner-xc2028.c b/drivers/media/common/tuners/tuner-xc2028.c
index f270e605da83..96f45a80fe56 100644
--- a/drivers/media/common/tuners/tuner-xc2028.c
+++ b/drivers/media/common/tuners/tuner-xc2028.c
@@ -917,30 +917,68 @@ static int generic_set_freq(struct dvb_frontend *fe, u32 freq /* in HZ */,
          * that xc2028 will be in a safe state.
          * Maybe this might also be needed for DTV.
          */
-        if (new_mode == T_ANALOG_TV)
+        if (new_mode == T_ANALOG_TV) {
                 rc = send_seq(priv, {0x00, 0x00});
 
-        /*
-         * Digital modes require an offset to adjust to the
-         * proper frequency.
-         * Analog modes require offset = 0
-         */
-        if (new_mode == T_DIGITAL_TV) {
-                /* Sets the offset according with firmware */
+                /* Analog modes require offset = 0 */
+        } else {
+                /*
+                 * Digital modes require an offset to adjust to the
+                 * proper frequency. The offset depends on what
+                 * firmware version is used.
+                 */
+
+                /*
+                 * Adjust to the center frequency. This is calculated by the
+                 * formula: offset = 1.25MHz - BW/2
+                 * For DTV 7/8, the firmware uses BW = 8000, so it needs a
+                 * further adjustment to get the frequency center on VHF
+                 */
                 if (priv->cur_fw.type & DTV6)
                         offset = 1750000;
                 else if (priv->cur_fw.type & DTV7)
                         offset = 2250000;
                 else    /* DTV8 or DTV78 */
                         offset = 2750000;
+                if ((priv->cur_fw.type & DTV78) && freq < 470000000)
+                        offset -= 500000;
 
                 /*
-                 * We must adjust the offset by 500kHz  when
-                 * tuning a 7MHz VHF channel with DTV78 firmware
-                 * (used in Australia, Italy and Germany)
+                 * xc3028 additional "magic"
+                 * Depending on the firmware version, it needs some adjustments
+                 * to properly centralize the frequency. This seems to be
+                 * needed to compensate the SCODE table adjustments made by
+                 * newer firmwares
                  */
-                if ((priv->cur_fw.type & DTV78) && freq < 470000000)
-                        offset -= 500000;
+
+#if 1
+                /*
+                 * The proper adjustment would be to do it at s-code table.
+                 * However, this didn't work, as reported by
+                 * Robert Lowery <rglowery@exemail.com.au>
+                 */
+
+                if (priv->cur_fw.type & DTV7)
+                        offset += 500000;
+
+#else
+                /*
+                 * Still need tests for XC3028L (firmware 3.2 or upper)
+                 * So, for now, let's just comment the per-firmware
+                 * version of this change. Reports with xc3028l working
+                 * with and without the lines bellow are welcome
+                 */
+
+                if (priv->firm_version < 0x0302) {
+                        if (priv->cur_fw.type & DTV7)
+                                offset += 500000;
+                } else {
+                        if (priv->cur_fw.type & DTV7)
+                                offset -= 300000;
+                        else if (type != ATSC) /* DVB @6MHz, DTV 8 and DTV 7/8 */
+                                offset += 200000;
+                }
+#endif
         }
 
         div = (freq - offset + DIV / 2) / DIV;
@@ -1097,17 +1135,22 @@ static int xc2028_set_params(struct dvb_frontend *fe,
 
         /* All S-code tables need a 200kHz shift */
         if (priv->ctrl.demod) {
-                demod = priv->ctrl.demod + 200;
+                /*
+                 * Newer firmwares require a 200 kHz offset only for ATSC
+                 */
+                if (type == ATSC || priv->firm_version < 0x0302)
+                        demod = priv->ctrl.demod + 200;
                 /*
                  * The DTV7 S-code table needs a 700 kHz shift.
-                 * Thanks to Terry Wu <terrywu2009@gmail.com> for reporting this
                  *
                  * DTV7 is only used in Australia.  Germany or Italy may also
                  * use this firmware after initialization, but a tune to a UHF
                  * channel should then cause DTV78 to be used.
+                 *
+                 * Unfortunately, on real-field tests, the s-code offset
+                 * didn't work as expected, as reported by
+                 * Robert Lowery <rglowery@exemail.com.au>
                  */
-                if (type & DTV7)
-                        demod += 500;
         }
 
         return generic_set_freq(fe, p->frequency,