1 files changed, 81 insertions, 0 deletions

diff --git a/drivers/fc4/Kconfig b/drivers/fc4/Kconfig
new file mode 100644
index 000000000000..f00c02a13ed6
--- /dev/null
+++ b/drivers/fc4/Kconfig
@@ -0,0 +1,81 @@
+#
+# FC4 device configuration
+#
+
+menu "Fibre Channel support"
+
+config FC4
+        tristate "Fibre Channel and FC4 SCSI support"
+        ---help---
+          Fibre Channel is a high speed serial protocol mainly used to
+          connect large storage devices to the computer; it is compatible with
+          and intended to replace SCSI.
+
+          This is an experimental support for storage arrays connected to your
+          computer using optical fibre cables and the "X3.269-199X Fibre
+          Channel Protocol for SCSI" specification. If you want to use this,
+          you need to say Y here and to "SCSI support" as well as to the
+          drivers for the storage array itself and for the interface adapter
+          such as SOC or SOC+. This subsystem could even serve for IP
+          networking, with some code extensions.
+
+          If unsure, say N.
+
+comment "FC4 drivers"
+        depends on FC4
+
+config FC4_SOC
+        tristate "Sun SOC/Sbus"
+        depends on FC4!=n && (SPARC32 || SPARC64)
+        help
+          Serial Optical Channel is an interface card with one or two Fibre
+          Optic ports, each of which can be connected to a disk array. Note
+          that if you have older firmware in the card, you'll need the
+          microcode from the Solaris driver to make it work.
+
+          To compile this support as a module, choose M here: the module will
+          be called soc.
+
+config FC4_SOCAL
+        tristate "Sun SOC+ (aka SOCAL)"
+        depends on FC4!=n && (SPARC32 || SPARC64)
+        ---help---
+          Serial Optical Channel Plus is an interface card with up to two
+          Fibre Optic ports. This card supports FC Arbitrated Loop (usually
+          A5000 or internal FC disks in E[3-6]000 machines through the
+          Interface Board). You'll probably need the microcode from the
+          Solaris driver to make it work.
+
+          To compile this support as a module, choose M here: the module will
+          be called socal.
+
+comment "FC4 targets"
+        depends on FC4
+
+config SCSI_PLUTO
+        tristate "SparcSTORAGE Array 100 and 200 series"
+        depends on FC4!=n && SCSI
+        help
+          If you never bought a disk array made by Sun, go with N.
+
+          To compile this support as a module, choose M here: the module will
+          be called pluto.
+
+config SCSI_FCAL
+        tristate "Sun Enterprise Network Array (A5000 and EX500)" if SPARC32 || SPARC64
+        depends on FC4!=n && SCSI
+        help
+          This driver drives FC-AL disks connected through a Fibre Channel
+          card using the drivers/fc4 layer (currently only SOCAL). The most
+          common is either A5000 array or internal disks in E[3-6]000
+          machines.
+
+          To compile this support as a module, choose M here: the module will
+          be called fcal.
+
+config SCSI_FCAL
+        prompt "Generic FC-AL disk driver"
+        depends on FC4!=n && SCSI && !SPARC32 && !SPARC64
+
+endmenu
+