1 files changed, 597 insertions, 0 deletions

diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
new file mode 100644
index 000000000000..40fcda62c7a2
--- /dev/null
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -0,0 +1,597 @@
+/*
+ * Libata driver for the highpoint 372N and 302N UDMA66 ATA controllers.
+ *
+ * This driver is heavily based upon:
+ *
+ * linux/drivers/ide/pci/hpt366.c               Version 0.36    April 25, 2003
+ *
+ * Copyright (C) 1999-2003              Andre Hedrick <andre@linux-ide.org>
+ * Portions Copyright (C) 2001          Sun Microsystems, Inc.
+ * Portions Copyright (C) 2003          Red Hat Inc
+ *
+ *
+ * TODO
+ *      371N
+ *      Work out best PLL policy
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME        "pata_hpt3x2n"
+#define DRV_VERSION     "0.3"
+
+enum {
+        HPT_PCI_FAST    =       (1 << 31),
+        PCI66           =       (1 << 1),
+        USE_DPLL        =       (1 << 0)
+};
+
+struct hpt_clock {
+        u8      xfer_speed;
+        u32     timing;
+};
+
+struct hpt_chip {
+        const char *name;
+        struct hpt_clock *clocks[3];
+};
+
+/* key for bus clock timings
+ * bit
+ * 0:3    data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
+ *        DMA. cycles = value + 1
+ * 4:8    data_low_time. active time of DIOW_/DIOR_ for PIO and MW
+ *        DMA. cycles = value + 1
+ * 9:12   cmd_high_time. inactive time of DIOW_/DIOR_ during task file
+ *        register access.
+ * 13:17  cmd_low_time. active time of DIOW_/DIOR_ during task file
+ *        register access.
+ * 18:21  udma_cycle_time. clock freq and clock cycles for UDMA xfer.
+ *        during task file register access.
+ * 22:24  pre_high_time. time to initialize 1st cycle for PIO and MW DMA
+ *        xfer.
+ * 25:27  cmd_pre_high_time. time to initialize 1st PIO cycle for task
+ *        register access.
+ * 28     UDMA enable
+ * 29     DMA enable
+ * 30     PIO_MST enable. if set, the chip is in bus master mode during
+ *        PIO.
+ * 31     FIFO enable.
+ */
+ 
+/* 66MHz DPLL clocks */
+
+static struct hpt_clock hpt3x2n_clocks[] = {
+        {       XFER_UDMA_7,    0x1c869c62      },
+        {       XFER_UDMA_6,    0x1c869c62      },
+        {       XFER_UDMA_5,    0x1c8a9c62      },
+        {       XFER_UDMA_4,    0x1c8a9c62      },
+        {       XFER_UDMA_3,    0x1c8e9c62      },
+        {       XFER_UDMA_2,    0x1c929c62      },
+        {       XFER_UDMA_1,    0x1c9a9c62      },
+        {       XFER_UDMA_0,    0x1c829c62      },
+
+        {       XFER_MW_DMA_2,  0x2c829c62      },
+        {       XFER_MW_DMA_1,  0x2c829c66      },
+        {       XFER_MW_DMA_0,  0x2c829d2c      },
+
+        {       XFER_PIO_4,     0x0c829c62      },
+        {       XFER_PIO_3,     0x0c829c84      },
+        {       XFER_PIO_2,     0x0c829ca6      },
+        {       XFER_PIO_1,     0x0d029d26      },
+        {       XFER_PIO_0,     0x0d029d5e      },
+        {       0,              0x0d029d5e      }
+};
+
+/**
+ *      hpt3x2n_find_mode       -       reset the hpt3x2n bus
+ *      @ap: ATA port
+ *      @speed: transfer mode
+ *
+ *      Return the 32bit register programming information for this channel
+ *      that matches the speed provided. For the moment the clocks table
+ *      is hard coded but easy to change. This will be needed if we use
+ *      different DPLLs
+ */
+ 
+static u32 hpt3x2n_find_mode(struct ata_port *ap, int speed)
+{
+        struct hpt_clock *clocks = hpt3x2n_clocks;
+        
+        while(clocks->xfer_speed) {
+                if (clocks->xfer_speed == speed)
+                        return clocks->timing;
+                clocks++;
+        }
+        BUG();
+        return 0xffffffffU;     /* silence compiler warning */
+}
+
+/**
+ *      hpt3x2n_pre_reset       -       reset the hpt3x2n bus
+ *      @ap: ATA port to reset
+ *
+ *      Perform the initial reset handling for the 3x2n series controllers.
+ *      Reset the hardware and state machine, obtain the cable type.
+ */
+ 
+static int hpt3xn_pre_reset(struct ata_port *ap)
+{
+        u8 scr2, ata66;
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        
+        pci_read_config_byte(pdev, 0x5B, &scr2);
+        pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01);
+        /* Cable register now active */
+        pci_read_config_byte(pdev, 0x5A, &ata66);
+        /* Restore state */
+        pci_write_config_byte(pdev, 0x5B, scr2);
+        
+        if (ata66 & (1 << ap->port_no))
+                ap->cbl = ATA_CBL_PATA40;
+        else
+                ap->cbl = ATA_CBL_PATA80;
+
+        /* Reset the state machine */
+        pci_write_config_byte(pdev, 0x50, 0x37); 
+        pci_write_config_byte(pdev, 0x54, 0x37); 
+        udelay(100);
+
+        return ata_std_prereset(ap);
+}
+        
+/**
+ *      hpt3x2n_error_handler   -       probe the hpt3x2n bus
+ *      @ap: ATA port to reset
+ *
+ *      Perform the probe reset handling for the 3x2N
+ */
+ 
+static void hpt3x2n_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, hpt3xn_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+                                     
+/**
+ *      hpt3x2n_set_piomode             -       PIO setup
+ *      @ap: ATA interface
+ *      @adev: device on the interface
+ *
+ *      Perform PIO mode setup. 
+ */
+ 
+static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u32 addr1, addr2;
+        u32 reg;
+        u32 mode;
+        u8 fast;
+
+        addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+        addr2 = 0x51 + 4 * ap->port_no;
+        
+        /* Fast interrupt prediction disable, hold off interrupt disable */
+        pci_read_config_byte(pdev, addr2, &fast);
+        fast &= ~0x07;
+        pci_write_config_byte(pdev, addr2, fast);
+        
+        pci_read_config_dword(pdev, addr1, &reg);
+        mode = hpt3x2n_find_mode(ap, adev->pio_mode);
+        mode &= ~0x8000000;     /* No FIFO in PIO */
+        mode &= ~0x30070000;    /* Leave config bits alone */
+        reg &= 0x30070000;      /* Strip timing bits */
+        pci_write_config_dword(pdev, addr1, reg | mode);
+}
+
+/**
+ *      hpt3x2n_set_dmamode             -       DMA timing setup
+ *      @ap: ATA interface
+ *      @adev: Device being configured
+ *
+ *      Set up the channel for MWDMA or UDMA modes. Much the same as with
+ *      PIO, load the mode number and then set MWDMA or UDMA flag.
+ */
+ 
+static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u32 addr1, addr2;
+        u32 reg;
+        u32 mode;
+        u8 fast;
+
+        addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+        addr2 = 0x51 + 4 * ap->port_no;
+        
+        /* Fast interrupt prediction disable, hold off interrupt disable */
+        pci_read_config_byte(pdev, addr2, &fast);
+        fast &= ~0x07;
+        pci_write_config_byte(pdev, addr2, fast);
+        
+        pci_read_config_dword(pdev, addr1, &reg);
+        mode = hpt3x2n_find_mode(ap, adev->dma_mode);
+        mode |= 0x8000000;      /* FIFO in MWDMA or UDMA */
+        mode &= ~0xC0000000;    /* Leave config bits alone */
+        reg &= 0xC0000000;      /* Strip timing bits */
+        pci_write_config_dword(pdev, addr1, reg | mode);
+}
+
+/**
+ *      hpt3x2n_bmdma_end               -       DMA engine stop
+ *      @qc: ATA command
+ *
+ *      Clean up after the HPT3x2n and later DMA engine
+ */
+ 
+static void hpt3x2n_bmdma_stop(struct ata_queued_cmd *qc)
+{
+        struct ata_port *ap = qc->ap;
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        int mscreg = 0x50 + 2 * ap->port_no;
+        u8 bwsr_stat, msc_stat;
+        
+        pci_read_config_byte(pdev, 0x6A, &bwsr_stat);
+        pci_read_config_byte(pdev, mscreg, &msc_stat);
+        if (bwsr_stat & (1 << ap->port_no))
+                pci_write_config_byte(pdev, mscreg, msc_stat | 0x30);
+        ata_bmdma_stop(qc);
+}
+
+/**
+ *      hpt3x2n_set_clock       -       clock control
+ *      @ap: ATA port
+ *      @source: 0x21 or 0x23 for PLL or PCI sourced clock
+ *
+ *      Switch the ATA bus clock between the PLL and PCI clock sources
+ *      while correctly isolating the bus and resetting internal logic
+ *
+ *      We must use the DPLL for
+ *      -       writing
+ *      -       second channel UDMA7 (SATA ports) or higher
+ *      -       66MHz PCI
+ *      
+ *      or we will underclock the device and get reduced performance.
+ */
+ 
+static void hpt3x2n_set_clock(struct ata_port *ap, int source)
+{
+        unsigned long bmdma = ap->ioaddr.bmdma_addr;
+        
+        /* Tristate the bus */
+        outb(0x80, bmdma+0x73);
+        outb(0x80, bmdma+0x77);
+        
+        /* Switch clock and reset channels */
+        outb(source, bmdma+0x7B);
+        outb(0xC0, bmdma+0x79);
+        
+        /* Reset state machines */
+        outb(0x37, bmdma+0x70);
+        outb(0x37, bmdma+0x74);
+        
+        /* Complete reset */
+        outb(0x00, bmdma+0x79);
+        
+        /* Reconnect channels to bus */
+        outb(0x00, bmdma+0x73);
+        outb(0x00, bmdma+0x77);
+}
+
+/* Check if our partner interface is busy */
+
+static int hpt3x2n_pair_idle(struct ata_port *ap)
+{
+        struct ata_host *host = ap->host;
+        struct ata_port *pair = host->ports[ap->port_no ^ 1];
+        
+        if (pair->hsm_task_state == HSM_ST_IDLE)
+                return 1;
+        return 0;
+}
+
+static int hpt3x2n_use_dpll(struct ata_port *ap, int reading)
+{
+        long flags = (long)ap->host->private_data;
+        /* See if we should use the DPLL */
+        if (reading == 0)
+                return USE_DPLL;        /* Needed for write */
+        if (flags & PCI66)
+                return USE_DPLL;        /* Needed at 66Mhz */
+        return 0;       
+}
+
+static unsigned int hpt3x2n_qc_issue_prot(struct ata_queued_cmd *qc)
+{
+        struct ata_taskfile *tf = &qc->tf;
+        struct ata_port *ap = qc->ap;
+        int flags = (long)ap->host->private_data;
+        
+        if (hpt3x2n_pair_idle(ap)) {
+                int dpll = hpt3x2n_use_dpll(ap, (tf->flags & ATA_TFLAG_WRITE));
+                if ((flags & USE_DPLL) != dpll) {
+                        if (dpll == 1)
+                                hpt3x2n_set_clock(ap, 0x21);
+                        else
+                                hpt3x2n_set_clock(ap, 0x23);
+                }
+        }
+        return ata_qc_issue_prot(qc);
+}
+
+static struct scsi_host_template hpt3x2n_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+/*
+ *      Configuration for HPT3x2n.
+ */
+ 
+static struct ata_port_operations hpt3x2n_port_ops = {
+        .port_disable   = ata_port_disable,
+        .set_piomode    = hpt3x2n_set_piomode,
+        .set_dmamode    = hpt3x2n_set_dmamode,
+        .mode_filter    = ata_pci_default_filter,
+        
+        .tf_load        = ata_tf_load,
+        .tf_read        = ata_tf_read,
+        .check_status   = ata_check_status,
+        .exec_command   = ata_exec_command,
+        .dev_select     = ata_std_dev_select,
+
+        .freeze         = ata_bmdma_freeze,
+        .thaw           = ata_bmdma_thaw,
+        .error_handler  = hpt3x2n_error_handler,
+        .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup    = ata_bmdma_setup,
+        .bmdma_start    = ata_bmdma_start,
+        .bmdma_stop     = hpt3x2n_bmdma_stop,
+        .bmdma_status   = ata_bmdma_status,
+
+        .qc_prep        = ata_qc_prep,
+        .qc_issue       = hpt3x2n_qc_issue_prot,
+        .eng_timeout    = ata_eng_timeout,
+        .data_xfer      = ata_pio_data_xfer,
+
+        .irq_handler    = ata_interrupt,
+        .irq_clear      = ata_bmdma_irq_clear,
+
+        .port_start     = ata_port_start,
+        .port_stop      = ata_port_stop,
+        .host_stop      = ata_host_stop
+};      
+
+/**
+ *      hpt3xn_calibrate_dpll           -       Calibrate the DPLL loop
+ *      @dev: PCI device 
+ *
+ *      Perform a calibration cycle on the HPT3xN DPLL. Returns 1 if this
+ *      succeeds
+ */
+
+static int hpt3xn_calibrate_dpll(struct pci_dev *dev)
+{
+        u8 reg5b;
+        u32 reg5c;
+        int tries;
+ 
+        for(tries = 0; tries < 0x5000; tries++) {
+                udelay(50);
+                pci_read_config_byte(dev, 0x5b, &reg5b);
+                if (reg5b & 0x80) {
+                        /* See if it stays set */
+                        for(tries = 0; tries < 0x1000; tries ++) {
+                                pci_read_config_byte(dev, 0x5b, &reg5b);
+                                /* Failed ? */
+                                if ((reg5b & 0x80) == 0)
+                                        return 0;
+                        }
+                        /* Turn off tuning, we have the DPLL set */
+                        pci_read_config_dword(dev, 0x5c, &reg5c);
+                        pci_write_config_dword(dev, 0x5c, reg5c & ~ 0x100);
+                        return 1;
+                }
+        }
+        /* Never went stable */
+        return 0;
+}
+
+static int hpt3x2n_pci_clock(struct pci_dev *pdev)
+{
+        unsigned long freq;
+        u32 fcnt;
+        
+        pci_read_config_dword(pdev, 0x70/*CHECKME*/, &fcnt);
+        if ((fcnt >> 12) != 0xABCDE) {
+                printk(KERN_WARNING "hpt3xn: BIOS clock data not set.\n");
+                return 33;      /* Not BIOS set */
+        }
+        fcnt &= 0x1FF;
+        
+        freq = (fcnt * 77) / 192;
+        
+        /* Clamp to bands */
+        if (freq < 40)
+                return 33;
+        if (freq < 45)
+                return 40;
+        if (freq < 55)
+                return 50;
+        return 66;
+}
+
+/**
+ *      hpt3x2n_init_one                -       Initialise an HPT37X/302
+ *      @dev: PCI device
+ *      @id: Entry in match table
+ *
+ *      Initialise an HPT3x2n device. There are some interesting complications
+ *      here. Firstly the chip may report 366 and be one of several variants.
+ *      Secondly all the timings depend on the clock for the chip which we must
+ *      detect and look up
+ *
+ *      This is the known chip mappings. It may be missing a couple of later
+ *      releases.
+ *
+ *      Chip version            PCI             Rev     Notes
+ *      HPT372                  4 (HPT366)      5       Other driver
+ *      HPT372N                 4 (HPT366)      6       UDMA133
+ *      HPT372                  5 (HPT372)      1       Other driver
+ *      HPT372N                 5 (HPT372)      2       UDMA133
+ *      HPT302                  6 (HPT302)      *       Other driver
+ *      HPT302N                 6 (HPT302)      > 1     UDMA133
+ *      HPT371                  7 (HPT371)      *       Other driver
+ *      HPT371N                 7 (HPT371)      > 1     UDMA133
+ *      HPT374                  8 (HPT374)      *       Other driver
+ *      HPT372N                 9 (HPT372N)     *       UDMA133
+ *
+ *      (1) UDMA133 support depends on the bus clock
+ *
+ *      To pin down             HPT371N
+ */
+ 
+static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+        /* HPT372N and friends - UDMA133 */
+        static struct ata_port_info info = {
+                .sht = &hpt3x2n_sht,
+                .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask = 0x1f,
+                .mwdma_mask = 0x07,
+                .udma_mask = 0x7f,
+                .port_ops = &hpt3x2n_port_ops
+        };
+        struct ata_port_info *port_info[2];
+        struct ata_port_info *port = &info;
+
+        u8 irqmask;
+        u32 class_rev;
+        
+        unsigned int pci_mhz;
+        unsigned int f_low, f_high;
+        int adjust;
+        
+        pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
+        class_rev &= 0xFF;
+        
+        switch(dev->device) {
+                case PCI_DEVICE_ID_TTI_HPT366:
+                        if (class_rev < 6)
+                                return -ENODEV;
+                        break;
+                case PCI_DEVICE_ID_TTI_HPT372:
+                        /* 372N if rev >= 1*/
+                        if (class_rev == 0)
+                                return -ENODEV;
+                        break;
+                case PCI_DEVICE_ID_TTI_HPT302:
+                        if (class_rev < 2)
+                                return -ENODEV;
+                        break;
+                case PCI_DEVICE_ID_TTI_HPT372N:
+                        break;
+                default:
+                        printk(KERN_ERR "pata_hpt3x2n: PCI table is bogus please report (%d).\n", dev->device);
+                        return -ENODEV;
+        }
+
+        /* Ok so this is a chip we support */
+
+        pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
+        pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
+        pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
+        pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
+
+        pci_read_config_byte(dev, 0x5A, &irqmask);
+        irqmask &= ~0x10;
+        pci_write_config_byte(dev, 0x5a, irqmask);
+
+        /* Tune the PLL. HPT recommend using 75 for SATA, 66 for UDMA133 or
+           50 for UDMA100. Right now we always use 66 */
+           
+        pci_mhz = hpt3x2n_pci_clock(dev);
+        
+        f_low = (pci_mhz * 48) / 66;    /* PCI Mhz for 66Mhz DPLL */
+        f_high = f_low + 2;             /* Tolerance */
+        
+        pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low | 0x100);
+        /* PLL clock */
+        pci_write_config_byte(dev, 0x5B, 0x21);
+        
+        /* Unlike the 37x we don't try jiggling the frequency */
+        for(adjust = 0; adjust < 8; adjust++) {
+                if (hpt3xn_calibrate_dpll(dev))
+                        break;
+                pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low);
+        }
+        if (adjust == 8)
+                printk(KERN_WARNING "hpt3xn: DPLL did not stabilize.\n");
+
+        /* Set our private data up. We only need a few flags so we use
+           it directly */
+        port->private_data = NULL;
+        if (pci_mhz > 60)
+                port->private_data = (void *)PCI66;
+                
+        /* Now kick off ATA set up */
+        port_info[0] = port_info[1] = port;
+        return ata_pci_init_one(dev, port_info, 2);
+}
+
+static struct pci_device_id hpt3x2n[] = {
+        { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366), },
+        { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372), },
+        { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT302), },
+        { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372N), },
+        { 0, },
+};
+
+static struct pci_driver hpt3x2n_pci_driver = {
+        .name           = DRV_NAME,
+        .id_table       = hpt3x2n,
+        .probe          = hpt3x2n_init_one,
+        .remove         = ata_pci_remove_one
+};
+
+static int __init hpt3x2n_init(void)
+{
+        return pci_register_driver(&hpt3x2n_pci_driver);
+}
+
+
+static void __exit hpt3x2n_exit(void)
+{
+        pci_unregister_driver(&hpt3x2n_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for the Highpoint HPT3x2n/30x");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, hpt3x2n);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(hpt3x2n_init);
+module_exit(hpt3x2n_exit);