1 files changed, 38 insertions, 7 deletions

diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
index 78323923143a..6a34521b9e01 100644
--- a/drivers/ata/pata_hpt3x2n.c
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -8,10 +8,10 @@
  * Copyright (C) 1999-2003              Andre Hedrick <andre@linux-ide.org>
  * Portions Copyright (C) 2001          Sun Microsystems, Inc.
  * Portions Copyright (C) 2003          Red Hat Inc
+ * Portions Copyright (C) 2005-2006     MontaVista Software, Inc.
  *
  *
  * TODO
- *      371N
  *      Work out best PLL policy
  */
 
@@ -142,6 +142,7 @@ static int hpt3x2n_cable_detect(struct ata_port *ap)
 /**
  *      hpt3x2n_pre_reset       -       reset the hpt3x2n bus
  *      @ap: ATA port to reset
+ *      @deadline: deadline jiffies for the operation
  *
  *      Perform the initial reset handling for the 3x2n series controllers.
  *      Reset the hardware and state machine,
@@ -151,8 +152,7 @@ static int hpt3xn_pre_reset(struct ata_port *ap)
 {
         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
         /* Reset the state machine */
-        pci_write_config_byte(pdev, 0x50, 0x37);
-        pci_write_config_byte(pdev, 0x54, 0x37);
+        pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
         udelay(100);
         return ata_std_prereset(ap);
 }
@@ -433,8 +433,9 @@ static int hpt3x2n_pci_clock(struct pci_dev *pdev)
 {
         unsigned long freq;
         u32 fcnt;
+        unsigned long iobase = pci_resource_start(pdev, 4);
 
-        pci_read_config_dword(pdev, 0x70/*CHECKME*/, &fcnt);
+        fcnt = inl(iobase + 0x90);      /* Not PCI readable for some chips */
         if ((fcnt >> 12) != 0xABCDE) {
                 printk(KERN_WARNING "hpt3xn: BIOS clock data not set.\n");
                 return 33;      /* Not BIOS set */
@@ -503,6 +504,7 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
         unsigned int pci_mhz;
         unsigned int f_low, f_high;
         int adjust;
+        unsigned long iobase = pci_resource_start(dev, 4);
 
         pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
         class_rev &= 0xFF;
@@ -512,6 +514,11 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
                         if (class_rev < 6)
                                 return -ENODEV;
                         break;
+                case PCI_DEVICE_ID_TTI_HPT371:
+                        if (class_rev < 2)
+                                return -ENODEV;
+                        /* 371N if rev > 1 */
+                        break;
                 case PCI_DEVICE_ID_TTI_HPT372:
                         /* 372N if rev >= 1*/
                         if (class_rev == 0)
@@ -539,6 +546,19 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
         irqmask &= ~0x10;
         pci_write_config_byte(dev, 0x5a, irqmask);
 
+        /*
+         * HPT371 chips physically have only one channel, the secondary one,
+         * but the primary channel registers do exist!  Go figure...
+         * So,  we manually disable the non-existing channel here
+         * (if the BIOS hasn't done this already).
+         */
+        if (dev->device == PCI_DEVICE_ID_TTI_HPT371) {
+                u8 mcr1;
+                pci_read_config_byte(dev, 0x50, &mcr1);
+                mcr1 &= ~0x04;
+                pci_write_config_byte(dev, 0x50, mcr1);
+        }
+
         /* Tune the PLL. HPT recommend using 75 for SATA, 66 for UDMA133 or
            50 for UDMA100. Right now we always use 66 */
 
@@ -557,14 +577,24 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
                         break;
                 pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low);
         }
-        if (adjust == 8)
-                printk(KERN_WARNING "hpt3xn: DPLL did not stabilize.\n");
+        if (adjust == 8) {
+                printk(KERN_WARNING "hpt3x2n: DPLL did not stabilize.\n");
+                return -ENODEV;
+        }
 
         /* Set our private data up. We only need a few flags so we use
            it directly */
         port->private_data = NULL;
-        if (pci_mhz > 60)
+        if (pci_mhz > 60) {
                 port->private_data = (void *)PCI66;
+                /*
+                 * On  HPT371N, if ATA clock is 66 MHz we must set bit 2 in
+                 * the MISC. register to stretch the UltraDMA Tss timing.
+                 * NOTE: This register is only writeable via I/O space.
+                 */
+                if (dev->device == PCI_DEVICE_ID_TTI_HPT371)
+                        outb(inb(iobase + 0x9c) | 0x04, iobase + 0x9c);
+        }
 
         /* Now kick off ATA set up */
         port_info[0] = port_info[1] = port;
@@ -573,6 +603,7 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 
 static const struct pci_device_id hpt3x2n[] = {
         { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },
+        { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT371), },
         { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372), },
         { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT302), },
         { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372N), },