1 files changed, 518 insertions, 0 deletions

diff --git a/drivers/ata/pata_artop.c b/drivers/ata/pata_artop.c
new file mode 100644
index 000000000000..d6ef3bf1bac7
--- /dev/null
+++ b/drivers/ata/pata_artop.c
@@ -0,0 +1,518 @@
+/*
+ *    pata_artop.c - ARTOP ATA controller driver
+ *
+ *      (C) 2006 Red Hat <alan@redhat.com>
+ *
+ *    Based in part on drivers/ide/pci/aec62xx.c
+ *      Copyright (C) 1999-2002 Andre Hedrick <andre@linux-ide.org>
+ *      865/865R fixes for Macintosh card version from a patch to the old
+ *              driver by Thibaut VARENE <varenet@parisc-linux.org>
+ *      When setting the PCI latency we must set 0x80 or higher for burst
+ *              performance Alessandro Zummo <alessandro.zummo@towertech.it>
+ *
+ *      TODO
+ *      850 serialization once the core supports it
+ *      Investigate no_dsc on 850R
+ *      Clock detect
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/ata.h>
+
+#define DRV_NAME        "pata_artop"
+#define DRV_VERSION     "0.4.1"
+
+/*
+ *      The ARTOP has 33 Mhz and "over clocked" timing tables. Until we
+ *      get PCI bus speed functionality we leave this as 0. Its a variable
+ *      for when we get the functionality and also for folks wanting to
+ *      test stuff.
+ */
+
+static int clock = 0;
+
+static int artop6210_pre_reset(struct ata_port *ap)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        const struct pci_bits artop_enable_bits[] = {
+                { 0x4AU, 1U, 0x02UL, 0x02UL },  /* port 0 */
+                { 0x4AU, 1U, 0x04UL, 0x04UL },  /* port 1 */
+        };
+
+        if (!pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no])) {
+                ata_port_disable(ap);
+                printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+                return 0;
+        }
+        ap->cbl = ATA_CBL_PATA40;
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      artop6210_error_handler - Probe specified port on PATA host controller
+ *      @ap: Port to probe
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void artop6210_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, artop6210_pre_reset,
+                                    ata_std_softreset, NULL,
+                                    ata_std_postreset);
+}
+
+/**
+ *      artop6260_pre_reset     -       check for 40/80 pin
+ *      @ap: Port
+ *
+ *      The ARTOP hardware reports the cable detect bits in register 0x49.
+ *      Nothing complicated needed here.
+ */
+
+static int artop6260_pre_reset(struct ata_port *ap)
+{
+        static const struct pci_bits artop_enable_bits[] = {
+                { 0x4AU, 1U, 0x02UL, 0x02UL },  /* port 0 */
+                { 0x4AU, 1U, 0x04UL, 0x04UL },  /* port 1 */
+        };
+
+        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+        u8 tmp;
+
+        /* Odd numbered device ids are the units with enable bits (the -R cards) */
+        if (pdev->device % 1 && !pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no])) {
+                ata_port_disable(ap);
+                printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+                return 0;
+        }
+        pci_read_config_byte(pdev, 0x49, &tmp);
+        if (tmp & (1 >> ap->port_no))
+                ap->cbl = ATA_CBL_PATA40;
+        else
+                ap->cbl = ATA_CBL_PATA80;
+        return ata_std_prereset(ap);
+}
+
+/**
+ *      artop6260_error_handler - Probe specified port on PATA host controller
+ *      @ap: Port to probe
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void artop6260_error_handler(struct ata_port *ap)
+{
+        ata_bmdma_drive_eh(ap, artop6260_pre_reset,
+                                    ata_std_softreset, NULL,
+                                    ata_std_postreset);
+}
+
+/**
+ *      artop6210_load_piomode - Load a set of PATA PIO timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device
+ *      @pio: PIO mode
+ *
+ *      Set PIO mode for device, in host controller PCI config space. This
+ *      is used both to set PIO timings in PIO mode and also to set the
+ *      matching PIO clocking for UDMA, as well as the MWDMA timings.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void artop6210_load_piomode(struct ata_port *ap, struct ata_device *adev, unsigned int pio)
+{
+        struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
+        int dn = adev->devno + 2 * ap->port_no;
+        const u16 timing[2][5] = {
+                { 0x0000, 0x000A, 0x0008, 0x0303, 0x0301 },
+                { 0x0700, 0x070A, 0x0708, 0x0403, 0x0401 }
+
+        };
+        /* Load the PIO timing active/recovery bits */
+        pci_write_config_word(pdev, 0x40 + 2 * dn, timing[clock][pio]);
+}
+
+/**
+ *      artop6210_set_piomode - Initialize host controller PATA PIO timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device we are configuring
+ *
+ *      Set PIO mode for device, in host controller PCI config space. For
+ *      ARTOP we must also clear the UDMA bits if we are not doing UDMA. In
+ *      the event UDMA is used the later call to set_dmamode will set the
+ *      bits as required.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void artop6210_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
+        int dn = adev->devno + 2 * ap->port_no;
+        u8 ultra;
+
+        artop6210_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
+
+        /* Clear the UDMA mode bits (set_dmamode will redo this if needed) */
+        pci_read_config_byte(pdev, 0x54, &ultra);
+        ultra &= ~(3 << (2 * dn));
+        pci_write_config_byte(pdev, 0x54, ultra);
+}
+
+/**
+ *      artop6260_load_piomode - Initialize host controller PATA PIO timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device we are configuring
+ *      @pio: PIO mode
+ *
+ *      Set PIO mode for device, in host controller PCI config space. The
+ *      ARTOP6260 and relatives store the timing data differently.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void artop6260_load_piomode (struct ata_port *ap, struct ata_device *adev, unsigned int pio)
+{
+        struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
+        int dn = adev->devno + 2 * ap->port_no;
+        const u8 timing[2][5] = {
+                { 0x00, 0x0A, 0x08, 0x33, 0x31 },
+                { 0x70, 0x7A, 0x78, 0x43, 0x41 }
+
+        };
+        /* Load the PIO timing active/recovery bits */
+        pci_write_config_byte(pdev, 0x40 + dn, timing[clock][pio]);
+}
+
+/**
+ *      artop6260_set_piomode - Initialize host controller PATA PIO timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device we are configuring
+ *
+ *      Set PIO mode for device, in host controller PCI config space. For
+ *      ARTOP we must also clear the UDMA bits if we are not doing UDMA. In
+ *      the event UDMA is used the later call to set_dmamode will set the
+ *      bits as required.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void artop6260_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+        struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
+        u8 ultra;
+
+        artop6260_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
+
+        /* Clear the UDMA mode bits (set_dmamode will redo this if needed) */
+        pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra);
+        ultra &= ~(7 << (4  * adev->devno));    /* One nibble per drive */
+        pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra);
+}
+
+/**
+ *      artop6210_set_dmamode - Initialize host controller PATA PIO timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: um
+ *
+ *      Set DMA mode for device, in host controller PCI config space.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void artop6210_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+        unsigned int pio;
+        struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
+        int dn = adev->devno + 2 * ap->port_no;
+        u8 ultra;
+
+        if (adev->dma_mode == XFER_MW_DMA_0)
+                pio = 1;
+        else
+                pio = 4;
+
+        /* Load the PIO timing active/recovery bits */
+        artop6210_load_piomode(ap, adev, pio);
+
+        pci_read_config_byte(pdev, 0x54, &ultra);
+        ultra &= ~(3 << (2 * dn));
+
+        /* Add ultra DMA bits if in UDMA mode */
+        if (adev->dma_mode >= XFER_UDMA_0) {
+                u8 mode = (adev->dma_mode - XFER_UDMA_0) + 1 - clock;
+                if (mode == 0)
+                        mode = 1;
+                ultra |= (mode << (2 * dn));
+        }
+        pci_write_config_byte(pdev, 0x54, ultra);
+}
+
+/**
+ *      artop6260_set_dmamode - Initialize host controller PATA PIO timings
+ *      @ap: Port whose timings we are configuring
+ *      @adev: Device we are configuring
+ *
+ *      Set DMA mode for device, in host controller PCI config space. The
+ *      ARTOP6260 and relatives store the timing data differently.
+ *
+ *      LOCKING:
+ *      None (inherited from caller).
+ */
+
+static void artop6260_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+        unsigned int pio        = adev->pio_mode - XFER_PIO_0;
+        struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
+        u8 ultra;
+
+        if (adev->dma_mode == XFER_MW_DMA_0)
+                pio = 1;
+        else
+                pio = 4;
+
+        /* Load the PIO timing active/recovery bits */
+        artop6260_load_piomode(ap, adev, pio);
+
+        /* Add ultra DMA bits if in UDMA mode */
+        pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra);
+        ultra &= ~(7 << (4  * adev->devno));    /* One nibble per drive */
+        if (adev->dma_mode >= XFER_UDMA_0) {
+                u8 mode = adev->dma_mode - XFER_UDMA_0 + 1 - clock;
+                if (mode == 0)
+                        mode = 1;
+                ultra |= (mode << (4 * adev->devno));
+        }
+        pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra);
+}
+
+static struct scsi_host_template artop_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+};
+
+static const struct ata_port_operations artop6210_ops = {
+        .port_disable           = ata_port_disable,
+        .set_piomode            = artop6210_set_piomode,
+        .set_dmamode            = artop6210_set_dmamode,
+        .mode_filter            = ata_pci_default_filter,
+
+        .tf_load                = ata_tf_load,
+        .tf_read                = ata_tf_read,
+        .check_status           = ata_check_status,
+        .exec_command           = ata_exec_command,
+        .dev_select             = ata_std_dev_select,
+
+        .freeze                 = ata_bmdma_freeze,
+        .thaw                   = ata_bmdma_thaw,
+        .error_handler          = artop6210_error_handler,
+        .post_internal_cmd      = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup            = ata_bmdma_setup,
+        .bmdma_start            = ata_bmdma_start,
+        .bmdma_stop             = ata_bmdma_stop,
+        .bmdma_status           = ata_bmdma_status,
+        .qc_prep                = ata_qc_prep,
+        .qc_issue               = ata_qc_issue_prot,
+        .eng_timeout            = ata_eng_timeout,
+        .data_xfer              = ata_pio_data_xfer,
+
+        .irq_handler            = ata_interrupt,
+        .irq_clear              = ata_bmdma_irq_clear,
+
+        .port_start             = ata_port_start,
+        .port_stop              = ata_port_stop,
+        .host_stop              = ata_host_stop,
+};
+
+static const struct ata_port_operations artop6260_ops = {
+        .port_disable           = ata_port_disable,
+        .set_piomode            = artop6260_set_piomode,
+        .set_dmamode            = artop6260_set_dmamode,
+
+        .tf_load                = ata_tf_load,
+        .tf_read                = ata_tf_read,
+        .check_status           = ata_check_status,
+        .exec_command           = ata_exec_command,
+        .dev_select             = ata_std_dev_select,
+
+        .freeze                 = ata_bmdma_freeze,
+        .thaw                   = ata_bmdma_thaw,
+        .error_handler          = artop6260_error_handler,
+        .post_internal_cmd      = ata_bmdma_post_internal_cmd,
+
+        .bmdma_setup            = ata_bmdma_setup,
+        .bmdma_start            = ata_bmdma_start,
+        .bmdma_stop             = ata_bmdma_stop,
+        .bmdma_status           = ata_bmdma_status,
+        .qc_prep                = ata_qc_prep,
+        .qc_issue               = ata_qc_issue_prot,
+        .data_xfer              = ata_pio_data_xfer,
+
+        .eng_timeout            = ata_eng_timeout,
+
+        .irq_handler            = ata_interrupt,
+        .irq_clear              = ata_bmdma_irq_clear,
+
+        .port_start             = ata_port_start,
+        .port_stop              = ata_port_stop,
+        .host_stop              = ata_host_stop,
+};
+
+
+/**
+ *      artop_init_one - Register ARTOP ATA PCI device with kernel services
+ *      @pdev: PCI device to register
+ *      @ent: Entry in artop_pci_tbl matching with @pdev
+ *
+ *      Called from kernel PCI layer.
+ *
+ *      LOCKING:
+ *      Inherited from PCI layer (may sleep).
+ *
+ *      RETURNS:
+ *      Zero on success, or -ERRNO value.
+ */
+
+static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
+{
+        static int printed_version;
+        static struct ata_port_info info_6210 = {
+                .sht            = &artop_sht,
+                .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask       = 0x1f, /* pio0-4 */
+                .mwdma_mask     = 0x07, /* mwdma0-2 */
+                .udma_mask      = ATA_UDMA2,
+                .port_ops       = &artop6210_ops,
+        };
+        static struct ata_port_info info_626x = {
+                .sht            = &artop_sht,
+                .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask       = 0x1f, /* pio0-4 */
+                .mwdma_mask     = 0x07, /* mwdma0-2 */
+                .udma_mask      = ATA_UDMA4,
+                .port_ops       = &artop6260_ops,
+        };
+        static struct ata_port_info info_626x_fast = {
+                .sht            = &artop_sht,
+                .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+                .pio_mask       = 0x1f, /* pio0-4 */
+                .mwdma_mask     = 0x07, /* mwdma0-2 */
+                .udma_mask      = ATA_UDMA5,
+                .port_ops       = &artop6260_ops,
+        };
+        struct ata_port_info *port_info[2];
+        struct ata_port_info *info;
+        int ports = 2;
+
+        if (!printed_version++)
+                dev_printk(KERN_DEBUG, &pdev->dev,
+                           "version " DRV_VERSION "\n");
+
+        if (id->driver_data == 0) {     /* 6210 variant */
+                info = &info_6210;
+                /* BIOS may have left us in UDMA, clear it before libata probe */
+                pci_write_config_byte(pdev, 0x54, 0);
+                /* For the moment (also lacks dsc) */
+                printk(KERN_WARNING "ARTOP 6210 requires serialize functionality not yet supported by libata.\n");
+                printk(KERN_WARNING "Secondary ATA ports will not be activated.\n");
+                ports = 1;
+        }
+        else if (id->driver_data == 1)  /* 6260 */
+                info = &info_626x;
+        else if (id->driver_data == 2)  { /* 6260 or 6260 + fast */
+                unsigned long io = pci_resource_start(pdev, 4);
+                u8 reg;
+
+                info = &info_626x;
+                if (inb(io) & 0x10)
+                        info = &info_626x_fast;
+                /* Mac systems come up with some registers not set as we
+                   will need them */
+
+                /* Clear reset & test bits */
+                pci_read_config_byte(pdev, 0x49, &reg);
+                pci_write_config_byte(pdev, 0x49, reg & ~ 0x30);
+
+                /* PCI latency must be > 0x80 for burst mode, tweak it
+                 * if required.
+                 */
+                pci_read_config_byte(pdev, PCI_LATENCY_TIMER, &reg);
+                if (reg <= 0x80)
+                        pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x90);
+
+                /* Enable IRQ output and burst mode */
+                pci_read_config_byte(pdev, 0x4a, &reg);
+                pci_write_config_byte(pdev, 0x4a, (reg & ~0x01) | 0x80);
+
+        }
+        port_info[0] = port_info[1] = info;
+        return ata_pci_init_one(pdev, port_info, ports);
+}
+
+static const struct pci_device_id artop_pci_tbl[] = {
+        { 0x1191, 0x0005, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+        { 0x1191, 0x0006, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
+        { 0x1191, 0x0007, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
+        { 0x1191, 0x0008, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
+        { 0x1191, 0x0009, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
+        { }     /* terminate list */
+};
+
+static struct pci_driver artop_pci_driver = {
+        .name                   = DRV_NAME,
+        .id_table               = artop_pci_tbl,
+        .probe                  = artop_init_one,
+        .remove                 = ata_pci_remove_one,
+};
+
+static int __init artop_init(void)
+{
+        return pci_register_driver(&artop_pci_driver);
+}
+
+static void __exit artop_exit(void)
+{
+        pci_unregister_driver(&artop_pci_driver);
+}
+
+
+module_init(artop_init);
+module_exit(artop_exit);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("SCSI low-level driver for ARTOP PATA");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, artop_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+