1 files changed, 20 insertions, 1 deletions

diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index c729e6988bbb..2e1a7cb2ed5f 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -420,7 +420,7 @@ static const struct ata_port_info ahci_port_info[] = {
         /* board_ahci_mv */
         {
                 AHCI_HFLAGS     (AHCI_HFLAG_NO_NCQ | AHCI_HFLAG_NO_MSI |
-                                 AHCI_HFLAG_MV_PATA),
+                                 AHCI_HFLAG_MV_PATA | AHCI_HFLAG_NO_PMP),
                 .flags          = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
                                   ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA,
                 .pio_mask       = 0x1f, /* pio0-4 */
@@ -487,7 +487,9 @@ static const struct pci_device_id ahci_pci_tbl[] = {
         { PCI_VDEVICE(INTEL, 0x3a05), board_ahci }, /* ICH10 */
         { PCI_VDEVICE(INTEL, 0x3a25), board_ahci }, /* ICH10 */
         { PCI_VDEVICE(INTEL, 0x3b24), board_ahci }, /* PCH RAID */
+        { PCI_VDEVICE(INTEL, 0x3b25), board_ahci }, /* PCH RAID */
         { PCI_VDEVICE(INTEL, 0x3b2b), board_ahci }, /* PCH RAID */
+        { PCI_VDEVICE(INTEL, 0x3b2c), board_ahci }, /* PCH RAID */
 
         /* JMicron 360/1/3/5/6, match class to avoid IDE function */
         { PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
@@ -610,6 +612,15 @@ module_param(ahci_em_messages, int, 0444);
 MODULE_PARM_DESC(ahci_em_messages,
         "Set AHCI Enclosure Management Message type (0 = disabled, 1 = LED");
 
+#if defined(CONFIG_PATA_MARVELL) || defined(CONFIG_PATA_MARVELL_MODULE)
+static int marvell_enable;
+#else
+static int marvell_enable = 1;
+#endif
+module_param(marvell_enable, int, 0644);
+MODULE_PARM_DESC(marvell_enable, "Marvell SATA via AHCI (1 = enabled)");
+
+
 static inline int ahci_nr_ports(u32 cap)
 {
         return (cap & 0x1f) + 1;
@@ -732,6 +743,8 @@ static void ahci_save_initial_config(struct pci_dev *pdev,
                            "MV_AHCI HACK: port_map %x -> %x\n",
                            port_map,
                            port_map & mv);
+                dev_printk(KERN_ERR, &pdev->dev,
+                          "Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this.\n");
 
                 port_map &= mv;
         }
@@ -2533,6 +2546,12 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
         if (!printed_version++)
                 dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
 
+        /* The AHCI driver can only drive the SATA ports, the PATA driver
+           can drive them all so if both drivers are selected make sure
+           AHCI stays out of the way */
+        if (pdev->vendor == PCI_VENDOR_ID_MARVELL && !marvell_enable)
+                return -ENODEV;
+
         /* acquire resources */
         rc = pcim_enable_device(pdev);
         if (rc)