1 files changed, 145 insertions, 0 deletions

diff --git a/arch/m68knommu/platform/coldfire/sltimers.c b/arch/m68knommu/platform/coldfire/sltimers.c
new file mode 100644
index 000000000000..0a1b937c3e18
--- /dev/null
+++ b/arch/m68knommu/platform/coldfire/sltimers.c
@@ -0,0 +1,145 @@
+/***************************************************************************/
+
+/*
+ *      sltimers.c -- generic ColdFire slice timer support.
+ *
+ *      Copyright (C) 2009-2010, Philippe De Muyter <phdm@macqel.be>
+ *      based on
+ *      timers.c -- generic ColdFire hardware timer support.
+ *      Copyright (C) 1999-2008, Greg Ungerer <gerg@snapgear.com>
+ */
+
+/***************************************************************************/
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/profile.h>
+#include <linux/clocksource.h>
+#include <asm/io.h>
+#include <asm/traps.h>
+#include <asm/machdep.h>
+#include <asm/coldfire.h>
+#include <asm/mcfslt.h>
+#include <asm/mcfsim.h>
+
+/***************************************************************************/
+
+#ifdef CONFIG_HIGHPROFILE
+
+/*
+ *      By default use Slice Timer 1 as the profiler clock timer.
+ */
+#define PA(a)   (MCF_MBAR + MCFSLT_TIMER1 + (a))
+
+/*
+ *      Choose a reasonably fast profile timer. Make it an odd value to
+ *      try and get good coverage of kernel operations.
+ */
+#define PROFILEHZ       1013
+
+irqreturn_t mcfslt_profile_tick(int irq, void *dummy)
+{
+        /* Reset Slice Timer 1 */
+        __raw_writel(MCFSLT_SSR_BE | MCFSLT_SSR_TE, PA(MCFSLT_SSR));
+        if (current->pid)
+                profile_tick(CPU_PROFILING);
+        return IRQ_HANDLED;
+}
+
+static struct irqaction mcfslt_profile_irq = {
+        .name    = "profile timer",
+        .flags   = IRQF_DISABLED | IRQF_TIMER,
+        .handler = mcfslt_profile_tick,
+};
+
+void mcfslt_profile_init(void)
+{
+        printk(KERN_INFO "PROFILE: lodging TIMER 1 @ %dHz as profile timer\n",
+               PROFILEHZ);
+
+        setup_irq(MCF_IRQ_PROFILER, &mcfslt_profile_irq);
+
+        /* Set up TIMER 2 as high speed profile clock */
+        __raw_writel(MCF_BUSCLK / PROFILEHZ - 1, PA(MCFSLT_STCNT));
+        __raw_writel(MCFSLT_SCR_RUN | MCFSLT_SCR_IEN | MCFSLT_SCR_TEN,
+                                                                PA(MCFSLT_SCR));
+
+}
+
+#endif  /* CONFIG_HIGHPROFILE */
+
+/***************************************************************************/
+
+/*
+ *      By default use Slice Timer 0 as the system clock timer.
+ */
+#define TA(a)   (MCF_MBAR + MCFSLT_TIMER0 + (a))
+
+static u32 mcfslt_cycles_per_jiffy;
+static u32 mcfslt_cnt;
+
+static irqreturn_t mcfslt_tick(int irq, void *dummy)
+{
+        /* Reset Slice Timer 0 */
+        __raw_writel(MCFSLT_SSR_BE | MCFSLT_SSR_TE, TA(MCFSLT_SSR));
+        mcfslt_cnt += mcfslt_cycles_per_jiffy;
+        return arch_timer_interrupt(irq, dummy);
+}
+
+static struct irqaction mcfslt_timer_irq = {
+        .name    = "timer",
+        .flags   = IRQF_DISABLED | IRQF_TIMER,
+        .handler = mcfslt_tick,
+};
+
+static cycle_t mcfslt_read_clk(struct clocksource *cs)
+{
+        unsigned long flags;
+        u32 cycles;
+        u16 scnt;
+
+        local_irq_save(flags);
+        scnt = __raw_readl(TA(MCFSLT_SCNT));
+        cycles = mcfslt_cnt;
+        local_irq_restore(flags);
+
+        /* substract because slice timers count down */
+        return cycles - scnt;
+}
+
+static struct clocksource mcfslt_clk = {
+        .name   = "slt",
+        .rating = 250,
+        .read   = mcfslt_read_clk,
+        .shift  = 20,
+        .mask   = CLOCKSOURCE_MASK(32),
+        .flags  = CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+void hw_timer_init(void)
+{
+        mcfslt_cycles_per_jiffy = MCF_BUSCLK / HZ;
+        /*
+         *      The coldfire slice timer (SLT) runs from STCNT to 0 included,
+         *      then STCNT again and so on.  It counts thus actually
+         *      STCNT + 1 steps for 1 tick, not STCNT.  So if you want
+         *      n cycles, initialize STCNT with n - 1.
+         */
+        __raw_writel(mcfslt_cycles_per_jiffy - 1, TA(MCFSLT_STCNT));
+        __raw_writel(MCFSLT_SCR_RUN | MCFSLT_SCR_IEN | MCFSLT_SCR_TEN,
+                                                                TA(MCFSLT_SCR));
+        /* initialize mcfslt_cnt knowing that slice timers count down */
+        mcfslt_cnt = mcfslt_cycles_per_jiffy;
+
+        setup_irq(MCF_IRQ_TIMER, &mcfslt_timer_irq);
+
+        mcfslt_clk.mult = clocksource_hz2mult(MCF_BUSCLK, mcfslt_clk.shift);
+        clocksource_register(&mcfslt_clk);
+
+#ifdef CONFIG_HIGHPROFILE
+        mcfslt_profile_init();
+#endif
+}