1 files changed, 216 insertions, 0 deletions
diff --git a/arch/cris/arch-v32/mach-fs/Kconfig b/arch/cris/arch-v32/mach-fs/Kconfig
new file mode 100644
index 000000000000..f6d74475f1c6
--- /dev/null
+++ b/arch/cris/arch-v32/mach-fs/Kconfig
@@ -0,0 +1,216 @@
+if ETRAXFS
+menu "ETRAX FS options"
+       depends on ETRAXFS
+config ETRAX_DRAM_VIRTUAL_BASE
+        hex
+        depends on ETRAX_ARCH_V32
+        default "c0000000"
+config ETRAX_SERIAL_PORTS
+       int
+       default 4
+config ETRAX_MEM_GRP1_CONFIG
+        hex "MEM_GRP1_CONFIG"
+        depends on ETRAX_ARCH_V32
+        default "4044a"
+        help
+          Waitstates for flash. The default value is suitable for the
+          standard flashes used in axis products (120 ns).
+config ETRAX_MEM_GRP2_CONFIG
+        hex "MEM_GRP2_CONFIG"
+        depends on ETRAX_ARCH_V32
+        default "0"
+        help
+          Waitstates for SRAM. 0 is a good choice for most Axis products.
+config ETRAX_MEM_GRP3_CONFIG
+        hex "MEM_GRP3_CONFIG"
+        depends on ETRAX_ARCH_V32
+        default "0"
+        help
+          Waitstates for CSP0-3. 0 is a good choice for most Axis products.
+          It may need to be changed if external devices such as extra
+          register-mapped LEDs are used.
+config ETRAX_MEM_GRP4_CONFIG
+        hex "MEM_GRP4_CONFIG"
+        depends on ETRAX_ARCH_V32
+        default "0"
+        help
+          Waitstates for CSP4-6. 0 is a good choice for most Axis products.
+config ETRAX_SDRAM_GRP0_CONFIG
+        hex "SDRAM_GRP0_CONFIG"
+        depends on ETRAX_ARCH_V32
+        default "336"
+        help
+          SDRAM configuration for group 0. The value depends on the
+          hardware configuration. The default value is suitable
+          for 32 MB organized as two 16 bits chips (e.g. Axis
+          part number 18550) connected as one 32 bit device (i.e. in
+          the same group).
+config ETRAX_SDRAM_GRP1_CONFIG
+        hex "SDRAM_GRP1_CONFIG"
+        depends on ETRAX_ARCH_V32
+        default "0"
+        help
+          SDRAM configuration for group 1. The defult value is 0
+          because group 1 is not used in the default configuration,
+          described in the help for SDRAM_GRP0_CONFIG.
+config ETRAX_SDRAM_TIMING
+        hex "SDRAM_TIMING"
+        depends on ETRAX_ARCH_V32
+        default "104a"
+        help
+          SDRAM timing parameters. The default value is ok for
+          most hardwares but large SDRAMs may require a faster
+          refresh (a.k.a 8K refresh). The default value implies
+          100MHz clock and SDR mode.
+config ETRAX_SDRAM_COMMAND
+        hex "SDRAM_COMMAND"
+        depends on ETRAX_ARCH_V32
+        default "0"
+        help
+          SDRAM command. Should be 0 unless you really know what
+          you are doing (may be != 0 for unusual address line
+          mappings such as in a MCM)..
+config ETRAX_DEF_GIO_PA_OE
+        hex "GIO_PA_OE"
+        depends on ETRAX_ARCH_V32
+        default "1c"
+        help
+          Configures the direction of general port A bits.  1 is out, 0 is in.
+          This is often totally different depending on the product used.
+          There are some guidelines though - if you know that only LED's are
+          connected to port PA, then they are usually connected to bits 2-4
+          and you can therefore use 1c.  On other boards which don't have the
+          LED's at the general ports, these bits are used for all kinds of
+          stuff.  If you don't know what to use, it is always safe to put all
+          as inputs, although floating inputs isn't good.
+config ETRAX_DEF_GIO_PA_OUT
+        hex "GIO_PA_OUT"
+        depends on ETRAX_ARCH_V32
+        default "00"
+        help
+          Configures the initial data for the general port A bits.  Most
+          products should use 00 here.
+config ETRAX_DEF_GIO_PB_OE
+        hex "GIO_PB_OE"
+        depends on ETRAX_ARCH_V32
+        default "00000"
+        help
+          Configures the direction of general port B bits.  1 is out, 0 is in.
+          This is often totally different depending on the product used.
+          There are some guidelines though - if you know that only LED's are
+          connected to port PA, then they are usually connected to bits 2-4
+          and you can therefore use 1c.  On other boards which don't have the
+          LED's at the general ports, these bits are used for all kinds of
+          stuff.  If you don't know what to use, it is always safe to put all
+          as inputs, although floating inputs isn't good.
+config ETRAX_DEF_GIO_PB_OUT
+        hex "GIO_PB_OUT"
+        depends on ETRAX_ARCH_V32
+        default "00000"
+        help
+          Configures the initial data for the general port B bits.  Most
+          products should use 00000 here.
+config ETRAX_DEF_GIO_PC_OE
+        hex "GIO_PC_OE"
+        depends on ETRAX_ARCH_V32
+        default "00000"
+        help
+          Configures the direction of general port C bits.  1 is out, 0 is in.
+          This is often totally different depending on the product used.
+          There are some guidelines though - if you know that only LED's are
+          connected to port PA, then they are usually connected to bits 2-4
+          and you can therefore use 1c.  On other boards which don't have the
+          LED's at the general ports, these bits are used for all kinds of
+          stuff.  If you don't know what to use, it is always safe to put all
+          as inputs, although floating inputs isn't good.
+config ETRAX_DEF_GIO_PC_OUT
+        hex "GIO_PC_OUT"
+        depends on ETRAX_ARCH_V32
+        default "00000"
+        help
+          Configures the initial data for the general port C bits.  Most
+          products should use 00000 here.
+config ETRAX_DEF_GIO_PD_OE
+        hex "GIO_PD_OE"
+        depends on ETRAX_ARCH_V32
+        default "00000"
+        help
+          Configures the direction of general port D bits.  1 is out, 0 is in.
+          This is often totally different depending on the product used.
+          There are some guidelines though - if you know that only LED's are
+          connected to port PA, then they are usually connected to bits 2-4
+          and you can therefore use 1c.  On other boards which don't have the
+          LED's at the general ports, these bits are used for all kinds of
+          stuff.  If you don't know what to use, it is always safe to put all
+          as inputs, although floating inputs isn't good.
+config ETRAX_DEF_GIO_PD_OUT
+        hex "GIO_PD_OUT"
+        depends on ETRAX_ARCH_V32
+        default "00000"
+        help
+          Configures the initial data for the general port D bits.  Most
+          products should use 00000 here.
+config ETRAX_DEF_GIO_PE_OE
+        hex "GIO_PE_OE"
+        depends on ETRAX_ARCH_V32
+        default "00000"
+        help
+          Configures the direction of general port E bits.  1 is out, 0 is in.
+          This is often totally different depending on the product used.
+          There are some guidelines though - if you know that only LED's are
+          connected to port PA, then they are usually connected to bits 2-4
+          and you can therefore use 1c.  On other boards which don't have the
+          LED's at the general ports, these bits are used for all kinds of
+          stuff.  If you don't know what to use, it is always safe to put all
+          as inputs, although floating inputs isn't good.
+config ETRAX_DEF_GIO_PE_OUT
+        hex "GIO_PE_OUT"
+        depends on ETRAX_ARCH_V32
+        default "00000"
+        help
+          Configures the initial data for the general port E bits.  Most
+          products should use 00000 here.
+config ETRAX_DEF_GIO_PV_OE
+        hex "GIO_PV_OE"
+        depends on ETRAX_VIRTUAL_GPIO
+        default "0000"
+        help
+          Configures the direction of virtual general port V bits. 1 is out,
+          0 is in. This is often totally different depending on the product
+          used. These bits are used for all kinds of stuff. If you don't know
+          what to use, it is always safe to put all as inputs, although
+          floating inputs isn't good.
+config ETRAX_DEF_GIO_PV_OUT
+        hex "GIO_PV_OUT"
+        depends on ETRAX_VIRTUAL_GPIO
+        default "0000"
+        help
+          Configures the initial data for the virtual general port V bits.
+          Most products should use 0000 here.
+endmenu
+endif

diff --git a/arch/cris/arch-v32/mach-fs/Kconfig b/arch/cris/arch-v32/mach-fs/Kconfig new file mode 100644 index 000000000000..f6d74475f1c6 --- /dev/null +++ b/arch/cris/arch-v32/mach-fs/Kconfig
@@ -0,0 +1,216 @@
	1	if ETRAXFS
	2
	3	menu "ETRAX FS options"
	4	depends on ETRAXFS
	5
	6	config ETRAX_DRAM_VIRTUAL_BASE
	7	hex
	8	depends on ETRAX_ARCH_V32
	9	default "c0000000"
	10
	11	config ETRAX_SERIAL_PORTS
	12	int
	13	default 4
	14
	15	config ETRAX_MEM_GRP1_CONFIG
	16	hex "MEM_GRP1_CONFIG"
	17	depends on ETRAX_ARCH_V32
	18	default "4044a"
	19	help
	20	Waitstates for flash. The default value is suitable for the
	21	standard flashes used in axis products (120 ns).
	22
	23	config ETRAX_MEM_GRP2_CONFIG
	24	hex "MEM_GRP2_CONFIG"
	25	depends on ETRAX_ARCH_V32
	26	default "0"
	27	help
	28	Waitstates for SRAM. 0 is a good choice for most Axis products.
	29
	30	config ETRAX_MEM_GRP3_CONFIG
	31	hex "MEM_GRP3_CONFIG"
	32	depends on ETRAX_ARCH_V32
	33	default "0"
	34	help
	35	Waitstates for CSP0-3. 0 is a good choice for most Axis products.
	36	It may need to be changed if external devices such as extra
	37	register-mapped LEDs are used.
	38
	39	config ETRAX_MEM_GRP4_CONFIG
	40	hex "MEM_GRP4_CONFIG"
	41	depends on ETRAX_ARCH_V32
	42	default "0"
	43	help
	44	Waitstates for CSP4-6. 0 is a good choice for most Axis products.
	45
	46	config ETRAX_SDRAM_GRP0_CONFIG
	47	hex "SDRAM_GRP0_CONFIG"
	48	depends on ETRAX_ARCH_V32
	49	default "336"
	50	help
	51	SDRAM configuration for group 0. The value depends on the
	52	hardware configuration. The default value is suitable
	53	for 32 MB organized as two 16 bits chips (e.g. Axis
	54	part number 18550) connected as one 32 bit device (i.e. in
	55	the same group).
	56
	57	config ETRAX_SDRAM_GRP1_CONFIG
	58	hex "SDRAM_GRP1_CONFIG"
	59	depends on ETRAX_ARCH_V32
	60	default "0"
	61	help
	62	SDRAM configuration for group 1. The defult value is 0
	63	because group 1 is not used in the default configuration,
	64	described in the help for SDRAM_GRP0_CONFIG.
	65
	66	config ETRAX_SDRAM_TIMING
	67	hex "SDRAM_TIMING"
	68	depends on ETRAX_ARCH_V32
	69	default "104a"
	70	help
	71	SDRAM timing parameters. The default value is ok for
	72	most hardwares but large SDRAMs may require a faster
	73	refresh (a.k.a 8K refresh). The default value implies
	74	100MHz clock and SDR mode.
	75
	76	config ETRAX_SDRAM_COMMAND
	77	hex "SDRAM_COMMAND"
	78	depends on ETRAX_ARCH_V32
	79	default "0"
	80	help
	81	SDRAM command. Should be 0 unless you really know what
	82	you are doing (may be != 0 for unusual address line
	83	mappings such as in a MCM)..
	84
	85	config ETRAX_DEF_GIO_PA_OE
	86	hex "GIO_PA_OE"
	87	depends on ETRAX_ARCH_V32
	88	default "1c"
	89	help
	90	Configures the direction of general port A bits. 1 is out, 0 is in.
	91	This is often totally different depending on the product used.
	92	There are some guidelines though - if you know that only LED's are
	93	connected to port PA, then they are usually connected to bits 2-4
	94	and you can therefore use 1c. On other boards which don't have the
	95	LED's at the general ports, these bits are used for all kinds of
	96	stuff. If you don't know what to use, it is always safe to put all
	97	as inputs, although floating inputs isn't good.
	98
	99	config ETRAX_DEF_GIO_PA_OUT
	100	hex "GIO_PA_OUT"
	101	depends on ETRAX_ARCH_V32
	102	default "00"
	103	help
	104	Configures the initial data for the general port A bits. Most
	105	products should use 00 here.
	106
	107	config ETRAX_DEF_GIO_PB_OE
	108	hex "GIO_PB_OE"
	109	depends on ETRAX_ARCH_V32
	110	default "00000"
	111	help
	112	Configures the direction of general port B bits. 1 is out, 0 is in.
	113	This is often totally different depending on the product used.
	114	There are some guidelines though - if you know that only LED's are
	115	connected to port PA, then they are usually connected to bits 2-4
	116	and you can therefore use 1c. On other boards which don't have the
	117	LED's at the general ports, these bits are used for all kinds of
	118	stuff. If you don't know what to use, it is always safe to put all
	119	as inputs, although floating inputs isn't good.
	120
	121	config ETRAX_DEF_GIO_PB_OUT
	122	hex "GIO_PB_OUT"
	123	depends on ETRAX_ARCH_V32
	124	default "00000"
	125	help
	126	Configures the initial data for the general port B bits. Most
	127	products should use 00000 here.
	128
	129	config ETRAX_DEF_GIO_PC_OE
	130	hex "GIO_PC_OE"
	131	depends on ETRAX_ARCH_V32
	132	default "00000"
	133	help
	134	Configures the direction of general port C bits. 1 is out, 0 is in.
	135	This is often totally different depending on the product used.
	136	There are some guidelines though - if you know that only LED's are
	137	connected to port PA, then they are usually connected to bits 2-4
	138	and you can therefore use 1c. On other boards which don't have the
	139	LED's at the general ports, these bits are used for all kinds of
	140	stuff. If you don't know what to use, it is always safe to put all
	141	as inputs, although floating inputs isn't good.
	142
	143	config ETRAX_DEF_GIO_PC_OUT
	144	hex "GIO_PC_OUT"
	145	depends on ETRAX_ARCH_V32
	146	default "00000"
	147	help
	148	Configures the initial data for the general port C bits. Most
	149	products should use 00000 here.
	150
	151	config ETRAX_DEF_GIO_PD_OE
	152	hex "GIO_PD_OE"
	153	depends on ETRAX_ARCH_V32
	154	default "00000"
	155	help
	156	Configures the direction of general port D bits. 1 is out, 0 is in.
	157	This is often totally different depending on the product used.
	158	There are some guidelines though - if you know that only LED's are
	159	connected to port PA, then they are usually connected to bits 2-4
	160	and you can therefore use 1c. On other boards which don't have the
	161	LED's at the general ports, these bits are used for all kinds of
	162	stuff. If you don't know what to use, it is always safe to put all
	163	as inputs, although floating inputs isn't good.
	164
	165	config ETRAX_DEF_GIO_PD_OUT
	166	hex "GIO_PD_OUT"
	167	depends on ETRAX_ARCH_V32
	168	default "00000"
	169	help
	170	Configures the initial data for the general port D bits. Most
	171	products should use 00000 here.
	172
	173	config ETRAX_DEF_GIO_PE_OE
	174	hex "GIO_PE_OE"
	175	depends on ETRAX_ARCH_V32
	176	default "00000"
	177	help
	178	Configures the direction of general port E bits. 1 is out, 0 is in.
	179	This is often totally different depending on the product used.
	180	There are some guidelines though - if you know that only LED's are
	181	connected to port PA, then they are usually connected to bits 2-4
	182	and you can therefore use 1c. On other boards which don't have the
	183	LED's at the general ports, these bits are used for all kinds of
	184	stuff. If you don't know what to use, it is always safe to put all
	185	as inputs, although floating inputs isn't good.
	186
	187	config ETRAX_DEF_GIO_PE_OUT
	188	hex "GIO_PE_OUT"
	189	depends on ETRAX_ARCH_V32
	190	default "00000"
	191	help
	192	Configures the initial data for the general port E bits. Most
	193	products should use 00000 here.
	194
	195	config ETRAX_DEF_GIO_PV_OE
	196	hex "GIO_PV_OE"
	197	depends on ETRAX_VIRTUAL_GPIO
	198	default "0000"
	199	help
	200	Configures the direction of virtual general port V bits. 1 is out,
	201	0 is in. This is often totally different depending on the product
	202	used. These bits are used for all kinds of stuff. If you don't know
	203	what to use, it is always safe to put all as inputs, although
	204	floating inputs isn't good.
	205
	206	config ETRAX_DEF_GIO_PV_OUT
	207	hex "GIO_PV_OUT"
	208	depends on ETRAX_VIRTUAL_GPIO
	209	default "0000"
	210	help
	211	Configures the initial data for the virtual general port V bits.
	212	Most products should use 0000 here.
	213
	214	endmenu
	215
	216	endif