1 files changed, 120 insertions, 0 deletions

diff --git a/arch/cris/arch-v32/lib/dram_init.S b/arch/cris/arch-v32/lib/dram_init.S
new file mode 100644
index 000000000000..47b6cf5f4afd
--- /dev/null
+++ b/arch/cris/arch-v32/lib/dram_init.S
@@ -0,0 +1,120 @@
+/* $Id: dram_init.S,v 1.4 2005/04/24 18:48:32 starvik Exp $
+ *
+ * DRAM/SDRAM initialization - alter with care
+ * This file is intended to be included from other assembler files
+ *
+ * Note: This file may not modify r8 or r9 because they are used to
+ * carry information from the decompresser to the kernel
+ *
+ * Copyright (C) 2000-2003 Axis Communications AB
+ *
+ * Authors:  Mikael Starvik (starvik@axis.com)
+ */
+
+/* Just to be certain the config file is included, we include it here
+ * explicitely instead of depending on it being included in the file that
+ * uses this code.
+ */
+
+#include <linux/config.h>
+#include <asm/arch/hwregs/asm/reg_map_asm.h>
+#include <asm/arch/hwregs/asm/bif_core_defs_asm.h>
+
+        ;; WARNING! The registers r8 and r9 are used as parameters carrying
+        ;; information from the decompressor (if the kernel was compressed).
+        ;; They should not be used in the code below.
+
+        ; Refer to BIF MDS for a description of SDRAM initialization
+
+        ; Bank configuration
+        move.d   REG_ADDR(bif_core, regi_bif_core, rw_sdram_cfg_grp0), $r0
+        move.d   CONFIG_ETRAX_SDRAM_GRP0_CONFIG, $r1
+        move.d   $r1, [$r0]
+        move.d   REG_ADDR(bif_core, regi_bif_core, rw_sdram_cfg_grp1), $r0
+        move.d   CONFIG_ETRAX_SDRAM_GRP1_CONFIG, $r1
+        move.d   $r1, [$r0]
+
+        ; Calculate value of mrs_data
+        ; CAS latency = 2 && bus_width = 32 => 0x40
+        ; CAS latency = 3 && bus_width = 32 => 0x60
+        ; CAS latency = 2 && bus_width = 16 => 0x20
+        ; CAS latency = 3 && bus_width = 16 => 0x30
+
+        ; Check if value is already supplied in kernel config
+        move.d   CONFIG_ETRAX_SDRAM_COMMAND, $r2
+        bne      _set_timing
+        nop
+
+        move.d   0x40, $r4       ; Assume 32 bits and CAS latency = 2
+        move.d   CONFIG_ETRAX_SDRAM_TIMING, $r1
+        and.d    0x07, $r1       ; Get CAS latency
+        cmpq     2, $r1          ; CL = 2 ?
+        beq      _bw_check
+        nop
+        move.d   0x60, $r4
+
+_bw_check:
+        ; Assume that group 0 width is equal to group 1. This assumption
+        ; is wrong for a group 1 only hardware (such as the grand old
+        ; StorPoint+).
+        move.d   CONFIG_ETRAX_SDRAM_GRP0_CONFIG, $r1
+        and.d    0x200, $r1     ; DRAM width is bit 9
+        beq      _set_timing
+        lslq     2, $r4         ;  mrs_data starts at bit 2
+        lsrq     1, $r4         ;  16 bits. Shift down value.
+
+        ; Set timing parameters (refresh off to avoid Guinness TR 83)
+_set_timing:
+        move.d   CONFIG_ETRAX_SDRAM_TIMING, $r1
+        and.d    ~(3 << reg_bif_core_rw_sdram_timing___ref___lsb), $r1
+        move.d   REG_ADDR(bif_core, regi_bif_core, rw_sdram_timing), $r0
+        move.d   $r1, [$r0]
+
+        ; Issue NOP command
+        move.d REG_ADDR(bif_core, regi_bif_core, rw_sdram_cmd), $r5
+        moveq regk_bif_core_nop, $r1
+        move.d $r1, [$r5]
+
+        ; Wait 200us
+        move.d   10000, $r2
+1:      bne      1b
+        subq     1, $r2
+
+        ; Issue initialization command sequence
+        move.d   _sdram_commands_start, $r2
+        and.d    0x000fffff, $r2 ; Make sure commands are read from flash
+        move.d   _sdram_commands_end,  $r3
+        and.d    0x000fffff, $r3
+1:      clear.d  $r6
+        move.b   [$r2+], $r6    ; Load command
+        or.d     $r4, $r6       ; Add calculated mrs
+        move.d   $r6, [$r5]     ; Write rw_sdram_cmd
+        ; Wait 80 ns between each command
+        move.d   4000, $r7
+2:      bne      2b
+        subq     1, $r7
+        cmp.d    $r2, $r3       ; Last command?
+        bne      1b
+        nop
+
+        ; Start refresh
+        move.d   CONFIG_ETRAX_SDRAM_TIMING, $r1
+        move.d   REG_ADDR(bif_core, regi_bif_core, rw_sdram_timing), $r0
+        move.d   $r1, [$r0]
+
+        ; Initialization finished
+        ba       _sdram_commands_end
+        nop
+
+_sdram_commands_start:
+        .byte   regk_bif_core_pre ; Precharge
+        .byte   regk_bif_core_ref ; refresh
+        .byte   regk_bif_core_ref ; refresh
+        .byte   regk_bif_core_ref ; refresh
+        .byte   regk_bif_core_ref ; refresh
+        .byte   regk_bif_core_ref ; refresh
+        .byte   regk_bif_core_ref ; refresh
+        .byte   regk_bif_core_ref ; refresh
+        .byte   regk_bif_core_ref ; refresh
+        .byte   regk_bif_core_mrs ; mrs
+_sdram_commands_end: