1 files changed, 266 insertions, 0 deletions

diff --git a/arch/arm/mach-mx3/mach-mx31_3ds.c b/arch/arm/mach-mx3/mach-mx31_3ds.c
new file mode 100644
index 000000000000..b88c18ad7698
--- /dev/null
+++ b/arch/arm/mach-mx3/mach-mx31_3ds.c
@@ -0,0 +1,266 @@
+/*
+ *  Copyright 2008 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/clk.h>
+#include <linux/irq.h>
+#include <linux/gpio.h>
+#include <linux/smsc911x.h>
+#include <linux/platform_device.h>
+
+#include <mach/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+#include <asm/memory.h>
+#include <asm/mach/map.h>
+#include <mach/common.h>
+#include <mach/board-mx31pdk.h>
+#include <mach/imx-uart.h>
+#include <mach/iomux-mx3.h>
+#include "devices.h"
+
+/*!
+ * @file mx31pdk.c
+ *
+ * @brief This file contains the board-specific initialization routines.
+ *
+ * @ingroup System
+ */
+
+static int mx31pdk_pins[] = {
+        /* UART1 */
+        MX31_PIN_CTS1__CTS1,
+        MX31_PIN_RTS1__RTS1,
+        MX31_PIN_TXD1__TXD1,
+        MX31_PIN_RXD1__RXD1,
+        IOMUX_MODE(MX31_PIN_GPIO1_1, IOMUX_CONFIG_GPIO),
+};
+
+static struct imxuart_platform_data uart_pdata = {
+        .flags = IMXUART_HAVE_RTSCTS,
+};
+
+/*
+ * Support for the SMSC9217 on the Debug board.
+ */
+
+static struct smsc911x_platform_config smsc911x_config = {
+        .irq_polarity   = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+        .irq_type       = SMSC911X_IRQ_TYPE_PUSH_PULL,
+        .flags          = SMSC911X_USE_16BIT | SMSC911X_FORCE_INTERNAL_PHY,
+        .phy_interface  = PHY_INTERFACE_MODE_MII,
+};
+
+static struct resource smsc911x_resources[] = {
+        {
+                .start          = LAN9217_BASE_ADDR,
+                .end            = LAN9217_BASE_ADDR + 0xff,
+                .flags          = IORESOURCE_MEM,
+        }, {
+                .start          = EXPIO_INT_ENET,
+                .end            = EXPIO_INT_ENET,
+                .flags          = IORESOURCE_IRQ,
+        },
+};
+
+static struct platform_device smsc911x_device = {
+        .name           = "smsc911x",
+        .id             = -1,
+        .num_resources  = ARRAY_SIZE(smsc911x_resources),
+        .resource       = smsc911x_resources,
+        .dev            = {
+                .platform_data = &smsc911x_config,
+        },
+};
+
+/*
+ * Routines for the CPLD on the debug board. It contains a CPLD handling
+ * LEDs, switches, interrupts for Ethernet.
+ */
+
+static void mx31pdk_expio_irq_handler(uint32_t irq, struct irq_desc *desc)
+{
+        uint32_t imr_val;
+        uint32_t int_valid;
+        uint32_t expio_irq;
+
+        imr_val = __raw_readw(CPLD_INT_MASK_REG);
+        int_valid = __raw_readw(CPLD_INT_STATUS_REG) & ~imr_val;
+
+        expio_irq = MXC_EXP_IO_BASE;
+        for (; int_valid != 0; int_valid >>= 1, expio_irq++) {
+                if ((int_valid & 1) == 0)
+                        continue;
+                generic_handle_irq(expio_irq);
+        }
+}
+
+/*
+ * Disable an expio pin's interrupt by setting the bit in the imr.
+ * @param irq           an expio virtual irq number
+ */
+static void expio_mask_irq(uint32_t irq)
+{
+        uint16_t reg;
+        uint32_t expio = MXC_IRQ_TO_EXPIO(irq);
+
+        /* mask the interrupt */
+        reg = __raw_readw(CPLD_INT_MASK_REG);
+        reg |= 1 << expio;
+        __raw_writew(reg, CPLD_INT_MASK_REG);
+}
+
+/*
+ * Acknowledge an expanded io pin's interrupt by clearing the bit in the isr.
+ * @param irq           an expanded io virtual irq number
+ */
+static void expio_ack_irq(uint32_t irq)
+{
+        uint32_t expio = MXC_IRQ_TO_EXPIO(irq);
+
+        /* clear the interrupt status */
+        __raw_writew(1 << expio, CPLD_INT_RESET_REG);
+        __raw_writew(0, CPLD_INT_RESET_REG);
+        /* mask the interrupt */
+        expio_mask_irq(irq);
+}
+
+/*
+ * Enable a expio pin's interrupt by clearing the bit in the imr.
+ * @param irq           a expio virtual irq number
+ */
+static void expio_unmask_irq(uint32_t irq)
+{
+        uint16_t reg;
+        uint32_t expio = MXC_IRQ_TO_EXPIO(irq);
+
+        /* unmask the interrupt */
+        reg = __raw_readw(CPLD_INT_MASK_REG);
+        reg &= ~(1 << expio);
+        __raw_writew(reg, CPLD_INT_MASK_REG);
+}
+
+static struct irq_chip expio_irq_chip = {
+        .ack = expio_ack_irq,
+        .mask = expio_mask_irq,
+        .unmask = expio_unmask_irq,
+};
+
+static int __init mx31pdk_init_expio(void)
+{
+        int i;
+        int ret;
+
+        /* Check if there's a debug board connected */
+        if ((__raw_readw(CPLD_MAGIC_NUMBER1_REG) != 0xAAAA) ||
+            (__raw_readw(CPLD_MAGIC_NUMBER2_REG) != 0x5555) ||
+            (__raw_readw(CPLD_MAGIC_NUMBER3_REG) != 0xCAFE)) {
+                /* No Debug board found */
+                return -ENODEV;
+        }
+
+        pr_info("i.MX31PDK Debug board detected, rev = 0x%04X\n",
+                __raw_readw(CPLD_CODE_VER_REG));
+
+        /*
+         * Configure INT line as GPIO input
+         */
+        ret = gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1), "sms9217-irq");
+        if (ret)
+                pr_warning("could not get LAN irq gpio\n");
+        else
+                gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1));
+
+        /* Disable the interrupts and clear the status */
+        __raw_writew(0, CPLD_INT_MASK_REG);
+        __raw_writew(0xFFFF, CPLD_INT_RESET_REG);
+        __raw_writew(0, CPLD_INT_RESET_REG);
+        __raw_writew(0x1F, CPLD_INT_MASK_REG);
+        for (i = MXC_EXP_IO_BASE;
+             i < (MXC_EXP_IO_BASE + MXC_MAX_EXP_IO_LINES);
+             i++) {
+                set_irq_chip(i, &expio_irq_chip);
+                set_irq_handler(i, handle_level_irq);
+                set_irq_flags(i, IRQF_VALID);
+        }
+        set_irq_type(EXPIO_PARENT_INT, IRQ_TYPE_LEVEL_LOW);
+        set_irq_chained_handler(EXPIO_PARENT_INT, mx31pdk_expio_irq_handler);
+
+        return 0;
+}
+
+/*
+ * This structure defines the MX31 memory map.
+ */
+static struct map_desc mx31pdk_io_desc[] __initdata = {
+        {
+                .virtual = MX31_CS5_BASE_ADDR_VIRT,
+                .pfn = __phys_to_pfn(MX31_CS5_BASE_ADDR),
+                .length = MX31_CS5_SIZE,
+                .type = MT_DEVICE,
+        },
+};
+
+/*
+ * Set up static virtual mappings.
+ */
+static void __init mx31pdk_map_io(void)
+{
+        mx31_map_io();
+        iotable_init(mx31pdk_io_desc, ARRAY_SIZE(mx31pdk_io_desc));
+}
+
+/*!
+ * Board specific initialization.
+ */
+static void __init mxc_board_init(void)
+{
+        mxc_iomux_setup_multiple_pins(mx31pdk_pins, ARRAY_SIZE(mx31pdk_pins),
+                                      "mx31pdk");
+
+        mxc_register_device(&mxc_uart_device0, &uart_pdata);
+
+        if (!mx31pdk_init_expio())
+                platform_device_register(&smsc911x_device);
+}
+
+static void __init mx31pdk_timer_init(void)
+{
+        mx31_clocks_init(26000000);
+}
+
+static struct sys_timer mx31pdk_timer = {
+        .init   = mx31pdk_timer_init,
+};
+
+/*
+ * The following uses standard kernel macros defined in arch.h in order to
+ * initialize __mach_desc_MX31PDK data structure.
+ */
+MACHINE_START(MX31_3DS, "Freescale MX31PDK (3DS)")
+        /* Maintainer: Freescale Semiconductor, Inc. */
+        .phys_io        = MX31_AIPS1_BASE_ADDR,
+        .io_pg_offst    = (MX31_AIPS1_BASE_ADDR_VIRT >> 18) & 0xfffc,
+        .boot_params    = MX3x_PHYS_OFFSET + 0x100,
+        .map_io         = mx31pdk_map_io,
+        .init_irq       = mx31_init_irq,
+        .init_machine   = mxc_board_init,
+        .timer          = &mx31pdk_timer,
+MACHINE_END