1 files changed, 136 insertions, 0 deletions

diff --git a/arch/arm/mach-kirkwood/sheevaplug-setup.c b/arch/arm/mach-kirkwood/sheevaplug-setup.c
new file mode 100644
index 000000000000..831e4a56cae1
--- /dev/null
+++ b/arch/arm/mach-kirkwood/sheevaplug-setup.c
@@ -0,0 +1,136 @@
+/*
+ * arch/arm/mach-kirkwood/sheevaplug-setup.c
+ *
+ * Marvell SheevaPlug Reference Board Setup
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <mach/kirkwood.h>
+#include <plat/mvsdio.h>
+#include <plat/orion_nand.h>
+#include "common.h"
+#include "mpp.h"
+
+static struct mtd_partition sheevaplug_nand_parts[] = {
+        {
+                .name = "u-boot",
+                .offset = 0,
+                .size = SZ_1M
+        }, {
+                .name = "uImage",
+                .offset = MTDPART_OFS_NXTBLK,
+                .size = SZ_4M
+        }, {
+                .name = "root",
+                .offset = MTDPART_OFS_NXTBLK,
+                .size = MTDPART_SIZ_FULL
+        },
+};
+
+static struct resource sheevaplug_nand_resource = {
+        .flags          = IORESOURCE_MEM,
+        .start          = KIRKWOOD_NAND_MEM_PHYS_BASE,
+        .end            = KIRKWOOD_NAND_MEM_PHYS_BASE +
+                          KIRKWOOD_NAND_MEM_SIZE - 1,
+};
+
+static struct orion_nand_data sheevaplug_nand_data = {
+        .parts          = sheevaplug_nand_parts,
+        .nr_parts       = ARRAY_SIZE(sheevaplug_nand_parts),
+        .cle            = 0,
+        .ale            = 1,
+        .width          = 8,
+        .chip_delay     = 25,
+};
+
+static struct platform_device sheevaplug_nand_flash = {
+        .name           = "orion_nand",
+        .id             = -1,
+        .dev            = {
+                .platform_data  = &sheevaplug_nand_data,
+        },
+        .resource       = &sheevaplug_nand_resource,
+        .num_resources  = 1,
+};
+
+static struct mv643xx_eth_platform_data sheevaplug_ge00_data = {
+        .phy_addr       = MV643XX_ETH_PHY_ADDR(0),
+};
+
+static struct mvsdio_platform_data sheevaplug_mvsdio_data = {
+        // unfortunately the CD signal has not been connected */
+};
+
+static struct gpio_led sheevaplug_led_pins[] = {
+        {
+                .name                   = "plug:green:health",
+                .default_trigger        = "default-on",
+                .gpio                   = 49,
+                .active_low             = 1,
+        },
+};
+
+static struct gpio_led_platform_data sheevaplug_led_data = {
+        .leds           = sheevaplug_led_pins,
+        .num_leds       = ARRAY_SIZE(sheevaplug_led_pins),
+};
+
+static struct platform_device sheevaplug_leds = {
+        .name   = "leds-gpio",
+        .id     = -1,
+        .dev    = {
+                .platform_data  = &sheevaplug_led_data,
+        }
+};
+
+static unsigned int sheevaplug_mpp_config[] __initdata = {
+        MPP29_GPIO,     /* USB Power Enable */
+        MPP49_GPIO,     /* LED */
+        0
+};
+
+static void __init sheevaplug_init(void)
+{
+        /*
+         * Basic setup. Needs to be called early.
+         */
+        kirkwood_init();
+        kirkwood_mpp_conf(sheevaplug_mpp_config);
+
+        kirkwood_uart0_init();
+
+        if (gpio_request(29, "USB Power Enable") != 0 ||
+            gpio_direction_output(29, 1) != 0)
+                printk(KERN_ERR "can't set up GPIO 29 (USB Power Enable)\n");
+        kirkwood_ehci_init();
+
+        kirkwood_ge00_init(&sheevaplug_ge00_data);
+        kirkwood_sdio_init(&sheevaplug_mvsdio_data);
+
+        platform_device_register(&sheevaplug_nand_flash);
+        platform_device_register(&sheevaplug_leds);
+}
+
+MACHINE_START(SHEEVAPLUG, "Marvell SheevaPlug Reference Board")
+        /* Maintainer: shadi Ammouri <shadi@marvell.com> */
+        .phys_io        = KIRKWOOD_REGS_PHYS_BASE,
+        .io_pg_offst    = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc,
+        .boot_params    = 0x00000100,
+        .init_machine   = sheevaplug_init,
+        .map_io         = kirkwood_map_io,
+        .init_irq       = kirkwood_init_irq,
+        .timer          = &kirkwood_timer,
+MACHINE_END