1 files changed, 133 insertions, 0 deletions

diff --git a/arch/arm/mach-ixp4xx/nas100d-setup.c b/arch/arm/mach-ixp4xx/nas100d-setup.c
new file mode 100644
index 000000000000..bde9648e7afc
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/nas100d-setup.c
@@ -0,0 +1,133 @@
+/*
+ * arch/arm/mach-ixp4xx/nas100d-setup.c
+ *
+ * NAS 100d board-setup
+ *
+ * based ixdp425-setup.c:
+ *      Copyright (C) 2003-2004 MontaVista Software, Inc.
+ *
+ * Author: Alessandro Zummo <a.zummo@towertech.it>
+ * Author: Rod Whitby <rod@whitby.id.au>
+ * Maintainers: http://www.nslu2-linux.org/
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/serial.h>
+#include <linux/serial_8250.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+static struct flash_platform_data nas100d_flash_data = {
+        .map_name               = "cfi_probe",
+        .width                  = 2,
+};
+
+static struct resource nas100d_flash_resource = {
+        .start                  = NAS100D_FLASH_BASE,
+        .end                    = NAS100D_FLASH_BASE + NAS100D_FLASH_SIZE,
+        .flags                  = IORESOURCE_MEM,
+};
+
+static struct platform_device nas100d_flash = {
+        .name                   = "IXP4XX-Flash",
+        .id                     = 0,
+        .dev.platform_data      = &nas100d_flash_data,
+        .num_resources          = 1,
+        .resource               = &nas100d_flash_resource,
+};
+
+static struct ixp4xx_i2c_pins nas100d_i2c_gpio_pins = {
+        .sda_pin                = NAS100D_SDA_PIN,
+        .scl_pin                = NAS100D_SCL_PIN,
+};
+
+static struct platform_device nas100d_i2c_controller = {
+        .name                   = "IXP4XX-I2C",
+        .id                     = 0,
+        .dev.platform_data      = &nas100d_i2c_gpio_pins,
+        .num_resources          = 0,
+};
+
+static struct resource nas100d_uart_resources[] = {
+        {
+                .start          = IXP4XX_UART1_BASE_PHYS,
+                .end            = IXP4XX_UART1_BASE_PHYS + 0x0fff,
+                .flags          = IORESOURCE_MEM,
+        },
+        {
+                .start          = IXP4XX_UART2_BASE_PHYS,
+                .end            = IXP4XX_UART2_BASE_PHYS + 0x0fff,
+                .flags          = IORESOURCE_MEM,
+        }
+};
+
+static struct plat_serial8250_port nas100d_uart_data[] = {
+        {
+                .mapbase        = IXP4XX_UART1_BASE_PHYS,
+                .membase        = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+                .irq            = IRQ_IXP4XX_UART1,
+                .flags          = UPF_BOOT_AUTOCONF,
+                .iotype         = UPIO_MEM,
+                .regshift       = 2,
+                .uartclk        = IXP4XX_UART_XTAL,
+        },
+        {
+                .mapbase        = IXP4XX_UART2_BASE_PHYS,
+                .membase        = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+                .irq            = IRQ_IXP4XX_UART2,
+                .flags          = UPF_BOOT_AUTOCONF,
+                .iotype         = UPIO_MEM,
+                .regshift       = 2,
+                .uartclk        = IXP4XX_UART_XTAL,
+        },
+        { }
+};
+
+static struct platform_device nas100d_uart = {
+        .name                   = "serial8250",
+        .id                     = PLAT8250_DEV_PLATFORM,
+        .dev.platform_data      = nas100d_uart_data,
+        .num_resources          = 2,
+        .resource               = nas100d_uart_resources,
+};
+
+static struct platform_device *nas100d_devices[] __initdata = {
+        &nas100d_i2c_controller,
+        &nas100d_flash,
+        &nas100d_uart,
+};
+
+static void nas100d_power_off(void)
+{
+        /* This causes the box to drop the power and go dead. */
+
+        /* enable the pwr cntl gpio */
+        gpio_line_config(NAS100D_PO_GPIO, IXP4XX_GPIO_OUT);
+
+        /* do the deed */
+        gpio_line_set(NAS100D_PO_GPIO, IXP4XX_GPIO_HIGH);
+}
+
+static void __init nas100d_init(void)
+{
+        ixp4xx_sys_init();
+
+        pm_power_off = nas100d_power_off;
+
+        platform_add_devices(nas100d_devices, ARRAY_SIZE(nas100d_devices));
+}
+
+MACHINE_START(NAS100D, "Iomega NAS 100d")
+        /* Maintainer: www.nslu2-linux.org */
+        .phys_ram       = PHYS_OFFSET,
+        .phys_io        = IXP4XX_PERIPHERAL_BASE_PHYS,
+        .io_pg_offst    = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xFFFC,
+        .boot_params    = 0x00000100,
+        .map_io         = ixp4xx_map_io,
+        .init_irq       = ixp4xx_init_irq,
+        .timer          = &ixp4xx_timer,
+        .init_machine   = nas100d_init,
+MACHINE_END