7 files changed, 311 insertions, 21 deletions

diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index cae5c67dc312..5bad6b9b00d7 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -30,6 +30,11 @@ config ARCH_AT91SAM9RL
         select GENERIC_TIME
         select GENERIC_CLOCKEVENTS
 
+config ARCH_AT91SAM9G20
+        bool "AT91SAM9G20"
+        select GENERIC_TIME
+        select GENERIC_CLOCKEVENTS
+
 config ARCH_AT91CAP9
         bool "AT91CAP9"
         select GENERIC_TIME
@@ -239,6 +244,20 @@ endif
 
 # ----------------------------------------------------------
 
+if ARCH_AT91SAM9G20
+
+comment "AT91SAM9G20 Board Type"
+
+config MACH_AT91SAM9G20EK
+        bool "Atmel AT91SAM9G20-EK Evaluation Kit"
+        depends on ARCH_AT91SAM9G20
+        help
+          Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit.
+
+endif
+
+# ----------------------------------------------------------
+
 if ARCH_AT91CAP9
 
 comment "AT91CAP9 Board Type"
@@ -274,13 +293,13 @@ comment "AT91 Board Options"
 
 config MTD_AT91_DATAFLASH_CARD
         bool "Enable DataFlash Card support"
-        depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91CAP9ADK || MACH_SAM9_L9260 || MACH_ECBAT91)
+        depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_ECBAT91 || MACH_SAM9_L9260 || MACH_AT91CAP9ADK)
         help
           Enable support for the DataFlash card.
 
 config MTD_NAND_AT91_BUSWIDTH_16
         bool "Enable 16-bit data bus interface to NAND flash"
-        depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91CAP9ADK)
+        depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91CAP9ADK)
         help
           On AT91SAM926x boards both types of NAND flash can be present
           (8 and 16 bit data bus width).
@@ -329,15 +348,15 @@ config AT91_EARLY_USART2
 
 config AT91_EARLY_USART3
         bool "USART3"
-        depends on (ARCH_AT91RM9200 || ARCH_AT91SAM9RL || ARCH_AT91SAM9260)
+        depends on (ARCH_AT91RM9200 || ARCH_AT91SAM9RL || ARCH_AT91SAM9260 || ARCH_AT91SAM9G20)
 
 config AT91_EARLY_USART4
         bool "USART4"
-        depends on ARCH_AT91SAM9260
+        depends on ARCH_AT91SAM9260 || ARCH_AT91SAM9G20
 
 config AT91_EARLY_USART5
         bool "USART5"
-        depends on ARCH_AT91SAM9260
+        depends on ARCH_AT91SAM9260 || ARCH_AT91SAM9G20
 
 endchoice
 
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index 932d17109e8b..7d641f97516b 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -15,6 +15,7 @@ obj-$(CONFIG_ARCH_AT91SAM9260)	+= at91sam9260.o at91sam926x_time.o at91sam9260_d
 obj-$(CONFIG_ARCH_AT91SAM9261)  += at91sam9261.o at91sam926x_time.o at91sam9261_devices.o
 obj-$(CONFIG_ARCH_AT91SAM9263)  += at91sam9263.o at91sam926x_time.o at91sam9263_devices.o
 obj-$(CONFIG_ARCH_AT91SAM9RL)   += at91sam9rl.o at91sam926x_time.o at91sam9rl_devices.o
+obj-$(CONFIG_ARCH_AT91SAM9G20)  += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o
 obj-$(CONFIG_ARCH_AT91CAP9)     += at91cap9.o at91sam926x_time.o at91cap9_devices.o
 obj-$(CONFIG_ARCH_AT91X40)      += at91x40.o at91x40_time.o
 
@@ -49,6 +50,9 @@ obj-$(CONFIG_MACH_USB_A9263)	+= board-usb-a9263.o
 # AT91SAM9RL board-specific support
 obj-$(CONFIG_MACH_AT91SAM9RLEK) += board-sam9rlek.o
 
+# AT91SAM9G20 board-specific support
+obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o
+
 # AT91CAP9 board-specific support
 obj-$(CONFIG_MACH_AT91CAP9ADK)  += board-cap9adk.o
 
diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c
index ee26550cdc21..380f12a12200 100644
--- a/arch/arm/mach-at91/at91sam9260.c
+++ b/arch/arm/mach-at91/at91sam9260.c
@@ -47,6 +47,20 @@ static struct map_desc at91sam9260_sram_desc[] __initdata = {
         }
 };
 
+static struct map_desc at91sam9g20_sram_desc[] __initdata = {
+        {
+                .virtual        = AT91_IO_VIRT_BASE - AT91SAM9G20_SRAM0_SIZE,
+                .pfn            = __phys_to_pfn(AT91SAM9G20_SRAM0_BASE),
+                .length         = AT91SAM9G20_SRAM0_SIZE,
+                .type           = MT_DEVICE,
+        }, {
+                .virtual        = AT91_IO_VIRT_BASE - AT91SAM9G20_SRAM0_SIZE - AT91SAM9G20_SRAM1_SIZE,
+                .pfn            = __phys_to_pfn(AT91SAM9G20_SRAM1_BASE),
+                .length         = AT91SAM9G20_SRAM1_SIZE,
+                .type           = MT_DEVICE,
+        }
+};
+
 static struct map_desc at91sam9xe_sram_desc[] __initdata = {
         {
                 .pfn            = __phys_to_pfn(AT91SAM9XE_SRAM_BASE),
@@ -307,6 +321,8 @@ void __init at91sam9260_initialize(unsigned long main_clock)
 
         if (cpu_is_at91sam9xe())
                 at91sam9xe_initialize();
+        else if (cpu_is_at91sam9g20())
+                iotable_init(at91sam9g20_sram_desc, ARRAY_SIZE(at91sam9g20_sram_desc));
         else
                 iotable_init(at91sam9260_sram_desc, ARRAY_SIZE(at91sam9260_sram_desc));
 
diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c
index 26f5cacbec35..86cba4ac29b1 100644
--- a/arch/arm/mach-at91/at91sam9260_devices.c
+++ b/arch/arm/mach-at91/at91sam9260_devices.c
@@ -18,6 +18,7 @@
 
 #include <asm/arch/board.h>
 #include <asm/arch/gpio.h>
+#include <asm/arch/cpu.h>
 #include <asm/arch/at91sam9260.h>
 #include <asm/arch/at91sam9260_matrix.h>
 #include <asm/arch/at91sam9_smc.h>
@@ -320,20 +321,41 @@ void __init at91_add_device_nand(struct at91_nand_data *data)
         csa = at91_sys_read(AT91_MATRIX_EBICSA);
         at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
 
-        /* set the bus interface characteristics */
-        at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0)
-                        | AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
+        if (cpu_is_at91sam9260()) {
+                /* Timing for sam9260 */
+                /* set the bus interface characteristics */
+                at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0)
+                                | AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
 
-        at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3)
-                        | AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
+                at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3)
+                                | AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
 
-        at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
+                at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
 
-        if (data->bus_width_16)
-                mode = AT91_SMC_DBW_16;
-        else
-                mode = AT91_SMC_DBW_8;
-        at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2));
+                if (data->bus_width_16)
+                        mode = AT91_SMC_DBW_16;
+                else
+                        mode = AT91_SMC_DBW_8;
+                at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2));
+        }
+
+        if (cpu_is_at91sam9g20()) {
+                /* Timing for sam9g20 */
+                /* set the bus interface characteristics */
+                at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0)
+                                | AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0));
+
+                at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(4)
+                                | AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(4));
+
+                at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7));
+
+                if (data->bus_width_16)
+                        mode = AT91_SMC_DBW_16;
+                else
+                        mode = AT91_SMC_DBW_8;
+                at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(3));
+        }
 
         /* enable pin */
         if (data->enable_pin)
diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c
new file mode 100644
index 000000000000..45617c201240
--- /dev/null
+++ b/arch/arm/mach-at91/board-sam9g20ek.c
@@ -0,0 +1,218 @@
+/*
+ *  Copyright (C) 2005 SAN People
+ *  Copyright (C) 2008 Atmel
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/at73c213.h>
+#include <linux/clk.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+
+#include "generic.h"
+
+
+static void __init ek_map_io(void)
+{
+        /* Initialize processor: 18.432 MHz crystal */
+        at91sam9260_initialize(18432000);
+
+        /* DGBU on ttyS0. (Rx & Tx only) */
+        at91_register_uart(0, 0, 0);
+
+        /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+        at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+                           | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+                           | ATMEL_UART_RI);
+
+        /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+        at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+        /* set serial console to ttyS0 (ie, DBGU) */
+        at91_set_serial_console(0);
+}
+
+static void __init ek_init_irq(void)
+{
+        at91sam9260_init_interrupts(NULL);
+}
+
+
+/*
+ * USB Host port
+ */
+static struct at91_usbh_data __initdata ek_usbh_data = {
+        .ports          = 2,
+};
+
+/*
+ * USB Device port
+ */
+static struct at91_udc_data __initdata ek_udc_data = {
+        .vbus_pin       = AT91_PIN_PC5,
+        .pullup_pin     = 0,            /* pull-up driven by UDC */
+};
+
+
+/*
+ * SPI devices.
+ */
+static struct spi_board_info ek_spi_devices[] = {
+#if !defined(CONFIG_MMC_AT91)
+        {       /* DataFlash chip */
+                .modalias       = "mtd_dataflash",
+                .chip_select    = 1,
+                .max_speed_hz   = 15 * 1000 * 1000,
+                .bus_num        = 0,
+        },
+#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
+        {       /* DataFlash card */
+                .modalias       = "mtd_dataflash",
+                .chip_select    = 0,
+                .max_speed_hz   = 15 * 1000 * 1000,
+                .bus_num        = 0,
+        },
+#endif
+#endif
+};
+
+
+/*
+ * MACB Ethernet device
+ */
+static struct at91_eth_data __initdata ek_macb_data = {
+        .phy_irq_pin    = AT91_PIN_PA7,
+        .is_rmii        = 1,
+};
+
+
+/*
+ * NAND flash
+ */
+static struct mtd_partition __initdata ek_nand_partition[] = {
+        {
+                .name   = "Bootstrap",
+                .offset = 0,
+                .size   = 4 * 1024 * 1024,
+        },
+        {
+                .name   = "Partition 1",
+                .offset = 4 * 1024 * 1024,
+                .size   = 60 * 1024 * 1024,
+        },
+        {
+                .name   = "Partition 2",
+                .offset = 64 * 1024 * 1024,
+                .size   = MTDPART_SIZ_FULL,
+        },
+};
+
+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
+{
+        *num_partitions = ARRAY_SIZE(ek_nand_partition);
+        return ek_nand_partition;
+}
+
+/* det_pin is not connected */
+static struct at91_nand_data __initdata ek_nand_data = {
+        .ale            = 21,
+        .cle            = 22,
+        .rdy_pin        = AT91_PIN_PC13,
+        .enable_pin     = AT91_PIN_PC14,
+        .partition_info = nand_partitions,
+#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+        .bus_width_16   = 1,
+#else
+        .bus_width_16   = 0,
+#endif
+};
+
+
+/*
+ * MCI (SD/MMC)
+ * det_pin, wp_pin and vcc_pin are not connected
+ */
+static struct at91_mmc_data __initdata ek_mmc_data = {
+        .slot_b         = 1,
+        .wire4          = 1,
+};
+
+
+/*
+ * LEDs
+ */
+static struct gpio_led ek_leds[] = {
+        {       /* "bottom" led, green, userled1 to be defined */
+                .name                   = "ds5",
+                .gpio                   = AT91_PIN_PA6,
+                .active_low             = 1,
+                .default_trigger        = "none",
+        },
+        {       /* "power" led, yellow */
+                .name                   = "ds1",
+                .gpio                   = AT91_PIN_PA9,
+                .default_trigger        = "heartbeat",
+        }
+};
+
+static void __init ek_board_init(void)
+{
+        /* Serial */
+        at91_add_device_serial();
+        /* USB Host */
+        at91_add_device_usbh(&ek_usbh_data);
+        /* USB Device */
+        at91_add_device_udc(&ek_udc_data);
+        /* SPI */
+        at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+        /* NAND */
+        at91_add_device_nand(&ek_nand_data);
+        /* Ethernet */
+        at91_add_device_eth(&ek_macb_data);
+        /* MMC */
+        at91_add_device_mmc(0, &ek_mmc_data);
+        /* I2C */
+        at91_add_device_i2c(NULL, 0);
+        /* LEDs */
+        at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
+}
+
+MACHINE_START(AT91SAM9G20EK, "Atmel AT91SAM9G20-EK")
+        /* Maintainer: Atmel */
+        .phys_io        = AT91_BASE_SYS,
+        .io_pg_offst    = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+        .boot_params    = AT91_SDRAM_BASE + 0x100,
+        .timer          = &at91sam926x_timer,
+        .map_io         = ek_map_io,
+        .init_irq       = ek_init_irq,
+        .init_machine   = ek_board_init,
+MACHINE_END
diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c
index e8ce8f0f3eda..464bdbbf74df 100644
--- a/arch/arm/mach-at91/clock.c
+++ b/arch/arm/mach-at91/clock.c
@@ -515,14 +515,19 @@ static unsigned __init at91_pll_calc(unsigned main_freq, unsigned out_freq)
                 /*
                  * PLL input between 1MHz and 32MHz per spec, but lower
                  * frequences seem necessary in some cases so allow 100K.
+                 * Warning: some newer products need 2MHz min.
                  */
                 input = main_freq / i;
+                if (cpu_is_at91sam9g20() && input < 2000000)
+                        continue;
                 if (input < 100000)
                         continue;
                 if (input > 32000000)
                         continue;
 
                 mul1 = out_freq / input;
+                if (cpu_is_at91sam9g20() && mul > 63)
+                        continue;
                 if (mul1 > 2048)
                         continue;
                 if (mul1 < 2)
@@ -582,7 +587,8 @@ int __init at91_clock_init(unsigned long main_clock)
 
         /* report if PLLA is more than mildly overclocked */
         plla.rate_hz = at91_pll_rate(&plla, main_clock, at91_sys_read(AT91_CKGR_PLLAR));
-        if (plla.rate_hz > 209000000)
+        if ((!cpu_is_at91sam9g20() && plla.rate_hz > 209000000)
+           || (cpu_is_at91sam9g20() && plla.rate_hz > 800000000))
                 pr_info("Clocks: PLLA overclocked, %ld MHz\n", plla.rate_hz / 1000000);
 
         /*
@@ -597,7 +603,7 @@ int __init at91_clock_init(unsigned long main_clock)
                 uhpck.pmc_mask = AT91RM9200_PMC_UHP;
                 udpck.pmc_mask = AT91RM9200_PMC_UDP;
                 at91_sys_write(AT91_PMC_SCER, AT91RM9200_PMC_MCKUDP);
-        } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263()) {
+        } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) {
                 uhpck.pmc_mask = AT91SAM926x_PMC_UHP;
                 udpck.pmc_mask = AT91SAM926x_PMC_UDP;
         } else if (cpu_is_at91cap9()) {
@@ -629,8 +635,13 @@ int __init at91_clock_init(unsigned long main_clock)
         freq /= (1 << ((mckr & AT91_PMC_PRES) >> 2));                           /* prescale */
         if (cpu_is_at91rm9200())
                 mck.rate_hz = freq / (1 + ((mckr & AT91_PMC_MDIV) >> 8));       /* mdiv */
-        else
-                mck.rate_hz = freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8));      /* mdiv */
+        else if (cpu_is_at91sam9g20()) {
+                mck.rate_hz = (mckr & AT91_PMC_MDIV) ?
+                        freq / ((mckr & AT91_PMC_MDIV) >> 7) : freq;    /* mdiv ; (x >> 7) = ((x >> 8) * 2) */
+                if (mckr & AT91_PMC_PDIV)
+                        freq /= 2;              /* processor clock division */
+        } else
+                mck.rate_hz = freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8));      /* mdiv */
 
         /* Register the PMC's standard clocks */
         for (i = 0; i < ARRAY_SIZE(standard_pmc_clocks); i++)
diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
index aa863c157708..8ab4feb1ec5b 100644
--- a/arch/arm/mach-at91/pm.c
+++ b/arch/arm/mach-at91/pm.c
@@ -202,7 +202,7 @@ static int at91_pm_verify_clocks(void)
                         pr_debug("AT91: PM - Suspend-to-RAM with USB still active\n");
                         return 0;
                 }
-        } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263()) {
+        } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) {
                 if ((scsr & (AT91SAM926x_PMC_UHP | AT91SAM926x_PMC_UDP)) != 0) {
                         pr_debug("AT91: PM - Suspend-to-RAM with USB still active\n");
                         return 0;