1 files changed, 218 insertions, 0 deletions

diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c
new file mode 100644
index 000000000000..45617c201240
--- /dev/null
+++ b/arch/arm/mach-at91/board-sam9g20ek.c
@@ -0,0 +1,218 @@
+/*
+ *  Copyright (C) 2005 SAN People
+ *  Copyright (C) 2008 Atmel
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/at73c213.h>
+#include <linux/clk.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+
+#include "generic.h"
+
+
+static void __init ek_map_io(void)
+{
+        /* Initialize processor: 18.432 MHz crystal */
+        at91sam9260_initialize(18432000);
+
+        /* DGBU on ttyS0. (Rx & Tx only) */
+        at91_register_uart(0, 0, 0);
+
+        /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+        at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+                           | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+                           | ATMEL_UART_RI);
+
+        /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+        at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+        /* set serial console to ttyS0 (ie, DBGU) */
+        at91_set_serial_console(0);
+}
+
+static void __init ek_init_irq(void)
+{
+        at91sam9260_init_interrupts(NULL);
+}
+
+
+/*
+ * USB Host port
+ */
+static struct at91_usbh_data __initdata ek_usbh_data = {
+        .ports          = 2,
+};
+
+/*
+ * USB Device port
+ */
+static struct at91_udc_data __initdata ek_udc_data = {
+        .vbus_pin       = AT91_PIN_PC5,
+        .pullup_pin     = 0,            /* pull-up driven by UDC */
+};
+
+
+/*
+ * SPI devices.
+ */
+static struct spi_board_info ek_spi_devices[] = {
+#if !defined(CONFIG_MMC_AT91)
+        {       /* DataFlash chip */
+                .modalias       = "mtd_dataflash",
+                .chip_select    = 1,
+                .max_speed_hz   = 15 * 1000 * 1000,
+                .bus_num        = 0,
+        },
+#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
+        {       /* DataFlash card */
+                .modalias       = "mtd_dataflash",
+                .chip_select    = 0,
+                .max_speed_hz   = 15 * 1000 * 1000,
+                .bus_num        = 0,
+        },
+#endif
+#endif
+};
+
+
+/*
+ * MACB Ethernet device
+ */
+static struct at91_eth_data __initdata ek_macb_data = {
+        .phy_irq_pin    = AT91_PIN_PA7,
+        .is_rmii        = 1,
+};
+
+
+/*
+ * NAND flash
+ */
+static struct mtd_partition __initdata ek_nand_partition[] = {
+        {
+                .name   = "Bootstrap",
+                .offset = 0,
+                .size   = 4 * 1024 * 1024,
+        },
+        {
+                .name   = "Partition 1",
+                .offset = 4 * 1024 * 1024,
+                .size   = 60 * 1024 * 1024,
+        },
+        {
+                .name   = "Partition 2",
+                .offset = 64 * 1024 * 1024,
+                .size   = MTDPART_SIZ_FULL,
+        },
+};
+
+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
+{
+        *num_partitions = ARRAY_SIZE(ek_nand_partition);
+        return ek_nand_partition;
+}
+
+/* det_pin is not connected */
+static struct at91_nand_data __initdata ek_nand_data = {
+        .ale            = 21,
+        .cle            = 22,
+        .rdy_pin        = AT91_PIN_PC13,
+        .enable_pin     = AT91_PIN_PC14,
+        .partition_info = nand_partitions,
+#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+        .bus_width_16   = 1,
+#else
+        .bus_width_16   = 0,
+#endif
+};
+
+
+/*
+ * MCI (SD/MMC)
+ * det_pin, wp_pin and vcc_pin are not connected
+ */
+static struct at91_mmc_data __initdata ek_mmc_data = {
+        .slot_b         = 1,
+        .wire4          = 1,
+};
+
+
+/*
+ * LEDs
+ */
+static struct gpio_led ek_leds[] = {
+        {       /* "bottom" led, green, userled1 to be defined */
+                .name                   = "ds5",
+                .gpio                   = AT91_PIN_PA6,
+                .active_low             = 1,
+                .default_trigger        = "none",
+        },
+        {       /* "power" led, yellow */
+                .name                   = "ds1",
+                .gpio                   = AT91_PIN_PA9,
+                .default_trigger        = "heartbeat",
+        }
+};
+
+static void __init ek_board_init(void)
+{
+        /* Serial */
+        at91_add_device_serial();
+        /* USB Host */
+        at91_add_device_usbh(&ek_usbh_data);
+        /* USB Device */
+        at91_add_device_udc(&ek_udc_data);
+        /* SPI */
+        at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+        /* NAND */
+        at91_add_device_nand(&ek_nand_data);
+        /* Ethernet */
+        at91_add_device_eth(&ek_macb_data);
+        /* MMC */
+        at91_add_device_mmc(0, &ek_mmc_data);
+        /* I2C */
+        at91_add_device_i2c(NULL, 0);
+        /* LEDs */
+        at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
+}
+
+MACHINE_START(AT91SAM9G20EK, "Atmel AT91SAM9G20-EK")
+        /* Maintainer: Atmel */
+        .phys_io        = AT91_BASE_SYS,
+        .io_pg_offst    = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+        .boot_params    = AT91_SDRAM_BASE + 0x100,
+        .timer          = &at91sam926x_timer,
+        .map_io         = ek_map_io,
+        .init_irq       = ek_init_irq,
+        .init_machine   = ek_board_init,
+MACHINE_END