1 files changed, 65 insertions, 15 deletions

diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
index 4977409d4fc6..d5266da55311 100644
--- a/arch/arm/mach-at91/board-sam9261ek.c
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -47,7 +47,9 @@
 #include <mach/board.h>
 #include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
+#include <mach/at91_shdwc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -76,7 +78,7 @@ static void __init ek_init_irq(void)
  * DM9000 ethernet device
  */
 #if defined(CONFIG_DM9000)
-static struct resource at91sam9261_dm9000_resource[] = {
+static struct resource dm9000_resource[] = {
         [0] = {
                 .start  = AT91_CHIPSELECT_2,
                 .end    = AT91_CHIPSELECT_2 + 3,
@@ -98,27 +100,42 @@ static struct dm9000_plat_data dm9000_platdata = {
         .flags          = DM9000_PLATF_16BITONLY,
 };
 
-static struct platform_device at91sam9261_dm9000_device = {
+static struct platform_device dm9000_device = {
         .name           = "dm9000",
         .id             = 0,
-        .num_resources  = ARRAY_SIZE(at91sam9261_dm9000_resource),
-        .resource       = at91sam9261_dm9000_resource,
+        .num_resources  = ARRAY_SIZE(dm9000_resource),
+        .resource       = dm9000_resource,
         .dev            = {
                 .platform_data  = &dm9000_platdata,
         }
 };
 
+/*
+ * SMC timings for the DM9000.
+ * Note: These timings were calculated for MASTER_CLOCK = 100000000 according to the DM9000 timings.
+ */
+static struct sam9_smc_config __initdata dm9000_smc_config = {
+        .ncs_read_setup         = 0,
+        .nrd_setup              = 2,
+        .ncs_write_setup        = 0,
+        .nwe_setup              = 2,
+
+        .ncs_read_pulse         = 8,
+        .nrd_pulse              = 4,
+        .ncs_write_pulse        = 8,
+        .nwe_pulse              = 4,
+
+        .read_cycle             = 16,
+        .write_cycle            = 16,
+
+        .mode                   = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16,
+        .tdf_cycles             = 1,
+};
+
 static void __init ek_add_device_dm9000(void)
 {
-        /*
-         * Configure Chip-Select 2 on SMC for the DM9000.
-         * Note: These timings were calculated for MASTER_CLOCK = 100000000
-         *  according to the DM9000 timings.
-         */
-        at91_sys_write(AT91_SMC_SETUP(2), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0) | AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0));
-        at91_sys_write(AT91_SMC_PULSE(2), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(8) | AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(8));
-        at91_sys_write(AT91_SMC_CYCLE(2), AT91_SMC_NWECYCLE_(16) | AT91_SMC_NRDCYCLE_(16));
-        at91_sys_write(AT91_SMC_MODE(2), AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16 | AT91_SMC_TDF_(1));
+        /* Configure chip-select 2 (DM9000) */
+        sam9_smc_configure(2, &dm9000_smc_config);
 
         /* Configure Reset signal as output */
         at91_set_gpio_output(AT91_PIN_PC10, 0);
@@ -126,7 +143,7 @@ static void __init ek_add_device_dm9000(void)
         /* Configure Interrupt pin as input, no pull-up */
         at91_set_gpio_input(AT91_PIN_PC11, 0);
 
-        platform_device_register(&at91sam9261_dm9000_device);
+        platform_device_register(&dm9000_device);
 }
 #else
 static void __init ek_add_device_dm9000(void) {}
@@ -197,6 +214,39 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 #endif
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+        .ncs_read_setup         = 0,
+        .nrd_setup              = 1,
+        .ncs_write_setup        = 0,
+        .nwe_setup              = 1,
+
+        .ncs_read_pulse         = 3,
+        .nrd_pulse              = 3,
+        .ncs_write_pulse        = 3,
+        .nwe_pulse              = 3,
+
+        .read_cycle             = 5,
+        .write_cycle            = 5,
+
+        .mode                   = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+        .tdf_cycles             = 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+        /* setup bus-width (8 or 16) */
+        if (ek_nand_data.bus_width_16)
+                ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
+        else
+                ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+        /* configure chip-select 3 (NAND) */
+        sam9_smc_configure(3, &ek_nand_smc_config);
+
+        at91_add_device_nand(&ek_nand_data);
+}
+
+
 /*
  * ADS7846 Touchscreen
  */
@@ -525,7 +575,7 @@ static void __init ek_board_init(void)
         /* I2C */
         at91_add_device_i2c(NULL, 0);
         /* NAND */
-        at91_add_device_nand(&ek_nand_data);
+        ek_add_device_nand();
         /* DM9000 ethernet */
         ek_add_device_dm9000();