1 files changed, 10 insertions, 43 deletions

diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c
index 9d833bbc592d..55dad3a46547 100644
--- a/arch/arm/mach-at91/board-picotux200.c
+++ b/arch/arm/mach-at91/board-picotux200.c
@@ -43,24 +43,21 @@
 #include "generic.h"
 
 
-/*
- * Serial port configuration.
- *    0 .. 3 = USART0 .. USART3
- *    4      = DBGU
- */
-static struct at91_uart_config __initdata picotux200_uart_config = {
-        .console_tty    = 0,                            /* ttyS0 */
-        .nr_tty         = 2,
-        .tty_map        = { 4, 1, -1, -1, -1 }          /* ttyS0, ..., ttyS4 */
-};
-
 static void __init picotux200_map_io(void)
 {
         /* Initialize processor: 18.432 MHz crystal */
         at91rm9200_initialize(18432000, AT91RM9200_BGA);
 
-        /* Setup the serial ports and console */
-        at91_init_serial(&picotux200_uart_config);
+        /* DBGU on ttyS0. (Rx & Tx only) */
+        at91_register_uart(0, 0, 0);
+
+        /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+        at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+                          | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+                          | ATMEL_UART_RI);
+
+        /* set serial console to ttyS0 (ie, DBGU) */
+        at91_set_serial_console(0);
 }
 
 static void __init picotux200_init_irq(void)
@@ -77,11 +74,6 @@ static struct at91_usbh_data __initdata picotux200_usbh_data = {
         .ports          = 1,
 };
 
-// static struct at91_udc_data __initdata picotux200_udc_data = {
-//      .vbus_pin       = AT91_PIN_PD4,
-//      .pullup_pin     = AT91_PIN_PD5,
-// };
-
 static struct at91_mmc_data __initdata picotux200_mmc_data = {
         .det_pin        = AT91_PIN_PB27,
         .slot_b         = 0,
@@ -89,21 +81,6 @@ static struct at91_mmc_data __initdata picotux200_mmc_data = {
         .wp_pin         = AT91_PIN_PA17,
 };
 
-// static struct spi_board_info picotux200_spi_devices[] = {
-//      {       /* DataFlash chip */
-//              .modalias       = "mtd_dataflash",
-//              .chip_select    = 0,
-//              .max_speed_hz   = 15 * 1000 * 1000,
-//      },
-// #ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
-//      {       /* DataFlash card */
-//              .modalias       = "mtd_dataflash",
-//              .chip_select    = 3,
-//              .max_speed_hz   = 15 * 1000 * 1000,
-//      },
-// #endif
-// };
-
 #define PICOTUX200_FLASH_BASE   AT91_CHIPSELECT_0
 #define PICOTUX200_FLASH_SIZE   SZ_4M
 
@@ -135,21 +112,11 @@ static void __init picotux200_board_init(void)
         at91_add_device_eth(&picotux200_eth_data);
         /* USB Host */
         at91_add_device_usbh(&picotux200_usbh_data);
-        /* USB Device */
-        // at91_add_device_udc(&picotux200_udc_data);
-        // at91_set_multi_drive(picotux200_udc_data.pullup_pin, 1);     /* pullup_pin is connected to reset */
         /* I2C */
         at91_add_device_i2c(NULL, 0);
-        /* SPI */
-        // at91_add_device_spi(picotux200_spi_devices, ARRAY_SIZE(picotux200_spi_devices));
-#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
-        /* DataFlash card */
-        at91_set_gpio_output(AT91_PIN_PB22, 0);
-#else
         /* MMC */
         at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */
         at91_add_device_mmc(0, &picotux200_mmc_data);
-#endif
         /* NOR Flash */
         platform_device_register(&picotux200_flash);
 }