1 files changed, 262 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/sun7i-a20-bananapro.dts b/arch/arm/boot/dts/sun7i-a20-bananapro.dts
new file mode 100644
index 000000000000..fb89fe7ed21b
--- /dev/null
+++ b/arch/arm/boot/dts/sun7i-a20-bananapro.dts
@@ -0,0 +1,262 @@
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+        model = "LeMaker Banana Pro";
+        compatible = "lemaker,bananapro", "allwinner,sun7i-a20";
+
+        leds {
+                compatible = "gpio-leds";
+                pinctrl-names = "default";
+                pinctrl-0 = <&led_pins_bananapro>;
+
+                blue {
+                        label = "bananapro:blue:usr";
+                        gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>;
+                };
+
+                green {
+                        label = "bananapro:green:usr";
+                        gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
+                };
+        };
+
+        reg_gmac_3v3: gmac-3v3 {
+                compatible = "regulator-fixed";
+                pinctrl-names = "default";
+                pinctrl-0 = <&gmac_power_pin_bananapro>;
+                regulator-name = "gmac-3v3";
+                regulator-min-microvolt = <3300000>;
+                regulator-max-microvolt = <3300000>;
+                startup-delay-us = <100000>;
+                enable-active-high;
+                gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>;
+        };
+
+        reg_vmmc3: vmmc3 {
+                compatible = "regulator-fixed";
+                pinctrl-names = "default";
+                pinctrl-0 = <&vmmc3_pin_bananapro>;
+                regulator-name = "vmmc3";
+                regulator-min-microvolt = <3300000>;
+                regulator-max-microvolt = <3300000>;
+                enable-active-high;
+                gpio = <&pio 7 22 GPIO_ACTIVE_HIGH>;
+        };
+};
+
+&ahci {
+        status = "okay";
+};
+
+&ehci0 {
+        status = "okay";
+};
+
+&ehci1 {
+        status = "okay";
+};
+
+&gmac {
+        pinctrl-names = "default";
+        pinctrl-0 = <&gmac_pins_rgmii_a>;
+        phy = <&phy1>;
+        phy-mode = "rgmii";
+        phy-supply = <&reg_gmac_3v3>;
+        status = "okay";
+
+        phy1: ethernet-phy@1 {
+                reg = <1>;
+        };
+};
+
+&i2c0 {
+        pinctrl-names = "default";
+        pinctrl-0 = <&i2c0_pins_a>;
+        status = "okay";
+
+        axp209: pmic@34 {
+                compatible = "x-powers,axp209";
+                reg = <0x34>;
+                interrupt-parent = <&nmi_intc>;
+                interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+                interrupt-controller;
+                #interrupt-cells = <1>;
+        };
+};
+
+&i2c2 {
+        pinctrl-names = "default";
+        pinctrl-0 = <&i2c2_pins_a>;
+        status = "okay";
+};
+
+&ir0 {
+        pinctrl-names = "default";
+        pinctrl-0 = <&ir0_pins_a>;
+        status = "okay";
+};
+
+&mmc0 {
+        pinctrl-names = "default";
+        pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapro>;
+        vmmc-supply = <&reg_vcc3v3>;
+        bus-width = <4>;
+        cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
+        cd-inverted;
+        status = "okay";
+};
+
+&mmc3 {
+        pinctrl-names = "default";
+        pinctrl-0 = <&mmc3_pins_a>;
+        vmmc-supply = <&reg_vmmc3>;
+        bus-width = <4>;
+        non-removable;
+        status = "okay";
+};
+
+&ohci0 {
+        status = "okay";
+};
+
+&ohci1 {
+        status = "okay";
+};
+
+&pio {
+        gmac_power_pin_bananapro: gmac_power_pin@0 {
+                allwinner,pins = "PH23";
+                allwinner,function = "gpio_out";
+                allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+                allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+        };
+
+        led_pins_bananapro: led_pins@0 {
+                allwinner,pins = "PH24", "PG2";
+                allwinner,function = "gpio_out";
+                allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+                allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+        };
+
+        mmc0_cd_pin_bananapro: mmc0_cd_pin@0 {
+                allwinner,pins = "PH10";
+                allwinner,function = "gpio_in";
+                allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+                allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+        };
+
+        usb1_vbus_pin_bananapro: usb1_vbus_pin@0 {
+                allwinner,pins = "PH0";
+                allwinner,function = "gpio_out";
+                allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+                allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+        };
+
+        usb2_vbus_pin_bananapro: usb2_vbus_pin@0 {
+                allwinner,pins = "PH1";
+                allwinner,function = "gpio_out";
+                allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+                allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+        };
+
+        vmmc3_pin_bananapro: vmmc3_pin@0 {
+                allwinner,pins = "PH22";
+                allwinner,function = "gpio_out";
+                allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+                allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+        };
+};
+
+&reg_usb1_vbus {
+        pinctrl-0 = <&usb1_vbus_pin_bananapro>;
+        gpio = <&pio 7 0 GPIO_ACTIVE_HIGH>; /* PH0 */
+        status = "okay";
+};
+
+&reg_usb2_vbus {
+        pinctrl-0 = <&usb2_vbus_pin_bananapro>;
+        gpio = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+        status = "okay";
+};
+
+&spi0 {
+        pinctrl-names = "default";
+        pinctrl-0 = <&spi0_pins_a>;
+        status = "okay";
+};
+
+&uart0 {
+        pinctrl-names = "default";
+        pinctrl-0 = <&uart0_pins_a>;
+        status = "okay";
+};
+
+&uart2 {
+        pinctrl-names = "default";
+        pinctrl-0 = <&uart2_pins_a>;
+        status = "okay";
+};
+
+&uart7 {
+        pinctrl-names = "default";
+        pinctrl-0 = <&uart7_pins_a>;
+        status = "okay";
+};
+
+&usbphy {
+        usb1_vbus-supply = <&reg_usb1_vbus>;
+        usb2_vbus-supply = <&reg_usb2_vbus>;
+        status = "okay";
+};