6 files changed, 54 insertions, 44 deletions

diff --git a/Documentation/cciss.txt b/Documentation/cciss.txt
index 63e59b8847c5..8244c6442faa 100644
--- a/Documentation/cciss.txt
+++ b/Documentation/cciss.txt
@@ -112,27 +112,18 @@ Hot plug support for SCSI tape drives
 
 Hot plugging of SCSI tape drives is supported, with some caveats.
 The cciss driver must be informed that changes to the SCSI bus
-have been made, in addition to and prior to informing the SCSI 
-mid layer.  This may be done via the /proc filesystem.  For example:
+have been made.  This may be done via the /proc filesystem.
+For example:
 
         echo "rescan" > /proc/scsi/cciss0/1
 
-This causes the adapter to query the adapter about changes to the 
-physical SCSI buses and/or fibre channel arbitrated loop and the 
+This causes the driver to query the adapter about changes to the
+physical SCSI buses and/or fibre channel arbitrated loop and the
 driver to make note of any new or removed sequential access devices
 or medium changers.  The driver will output messages indicating what 
 devices have been added or removed and the controller, bus, target and 
-lun used to address the device.  Once this is done, the SCSI mid layer 
-can be informed of changes to the virtual SCSI bus which the driver 
-presents to it in the usual way. For example: 
-
-        echo scsi add-single-device 3 2 1 0 > /proc/scsi/scsi
- 
-to add a device on controller 3, bus 2, target 1, lun 0.   Note that
-the driver makes an effort to preserve the devices positions
-in the virtual SCSI bus, so if you are only moving tape drives 
-around on the same adapter and not adding or removing tape drives 
-from the adapter, informing the SCSI mid layer may not be necessary.
+lun used to address the device.  It then notifies the SCSI mid layer
+of these changes.
 
 Note that the naming convention of the /proc filesystem entries 
 contains a number in addition to the driver name.  (E.g. "cciss0" 
diff --git a/Documentation/hwmon/dme1737 b/Documentation/hwmon/dme1737
index b1fe00999439..001d2e70bc11 100644
--- a/Documentation/hwmon/dme1737
+++ b/Documentation/hwmon/dme1737
@@ -10,6 +10,10 @@ Supported chips:
     Prefix: 'sch311x'
     Addresses scanned: none, address read from Super-I/O config space
     Datasheet: http://www.nuhorizons.com/FeaturedProducts/Volume1/SMSC/311x.pdf
+  * SMSC SCH5027
+    Prefix: 'sch5027'
+    Addresses scanned: I2C 0x2c, 0x2d, 0x2e
+    Datasheet: Provided by SMSC upon request and under NDA
 
 Authors:
     Juerg Haefliger <juergh@gmail.com>
@@ -27,33 +31,31 @@ Module Parameters
                         following boards:
                         - VIA EPIA SN18000
 
-Note that there is no need to use this parameter if the driver loads without
-complaining. The driver will say so if it is necessary.
-
 
 Description
 -----------
 
 This driver implements support for the hardware monitoring capabilities of the
-SMSC DME1737 and Asus A8000 (which are the same) and SMSC SCH311x Super-I/O
-chips. These chips feature monitoring of 3 temp sensors temp[1-3] (2 remote
-diodes and 1 internal), 7 voltages in[0-6] (6 external and 1 internal) and up
-to 6 fan speeds fan[1-6]. Additionally, the chips implement up to 5 PWM
-outputs pwm[1-3,5-6] for controlling fan speeds both manually and
+SMSC DME1737 and Asus A8000 (which are the same), SMSC SCH5027, and SMSC
+SCH311x Super-I/O chips. These chips feature monitoring of 3 temp sensors
+temp[1-3] (2 remote diodes and 1 internal), 7 voltages in[0-6] (6 external and
+1 internal) and up to 6 fan speeds fan[1-6]. Additionally, the chips implement
+up to 5 PWM outputs pwm[1-3,5-6] for controlling fan speeds both manually and
 automatically.
 
-For the DME1737 and A8000, fan[1-2] and pwm[1-2] are always present. Fan[3-6]
-and pwm[3,5-6] are optional features and their availability depends on the
-configuration of the chip. The driver will detect which features are present
-during initialization and create the sysfs attributes accordingly.
+For the DME1737, A8000 and SCH5027, fan[1-2] and pwm[1-2] are always present.
+Fan[3-6] and pwm[3,5-6] are optional features and their availability depends on
+the configuration of the chip. The driver will detect which features are
+present during initialization and create the sysfs attributes accordingly.
 
 For the SCH311x, fan[1-3] and pwm[1-3] are always present and fan[4-6] and
 pwm[5-6] don't exist.
 
-The hardware monitoring features of the DME1737 and A8000 are only accessible
-via SMBus, while the SCH311x only provides access via the ISA bus. The driver
-will therefore register itself as an I2C client driver if it detects a DME1737
-or A8000 and as a platform driver if it detects a SCH311x chip.
+The hardware monitoring features of the DME1737, A8000, and SCH5027 are only
+accessible via SMBus, while the SCH311x only provides access via the ISA bus.
+The driver will therefore register itself as an I2C client driver if it detects
+a DME1737, A8000, or SCH5027 and as a platform driver if it detects a SCH311x
+chip.
 
 
 Voltage Monitoring
@@ -64,6 +66,7 @@ scaling resistors. The values returned by the driver therefore reflect true
 millivolts and don't need scaling. The voltage inputs are mapped as follows
 (the last column indicates the input ranges):
 
+DME1737, A8000:
         in0: +5VTR      (+5V standby)           0V - 6.64V
         in1: Vccp       (processor core)        0V - 3V
         in2: VCC        (internal +3.3V)        0V - 4.38V
@@ -72,6 +75,24 @@ millivolts and don't need scaling. The voltage inputs are mapped as follows
         in5: VTR        (+3.3V standby)         0V - 4.38V
         in6: Vbat       (+3.0V)                 0V - 4.38V
 
+SCH311x:
+        in0: +2.5V                              0V - 6.64V
+        in1: Vccp       (processor core)        0V - 2V
+        in2: VCC        (internal +3.3V)        0V - 4.38V
+        in3: +5V                                0V - 6.64V
+        in4: +12V                               0V - 16V
+        in5: VTR        (+3.3V standby)         0V - 4.38V
+        in6: Vbat       (+3.0V)                 0V - 4.38V
+
+SCH5027:
+        in0: +5VTR      (+5V standby)           0V - 6.64V
+        in1: Vccp       (processor core)        0V - 3V
+        in2: VCC        (internal +3.3V)        0V - 4.38V
+        in3: V2_IN                              0V - 1.5V
+        in4: V1_IN                              0V - 1.5V
+        in5: VTR        (+3.3V standby)         0V - 4.38V
+        in6: Vbat       (+3.0V)                 0V - 4.38V
+
 Each voltage input has associated min and max limits which trigger an alarm
 when crossed.
 
diff --git a/Documentation/hwmon/it87 b/Documentation/hwmon/it87
index f4ce1fdbeff6..3496b7020e7c 100644
--- a/Documentation/hwmon/it87
+++ b/Documentation/hwmon/it87
@@ -6,12 +6,14 @@ Supported chips:
     Prefix: 'it87'
     Addresses scanned: from Super I/O config space (8 I/O ports)
     Datasheet: Publicly available at the ITE website
-               http://www.ite.com.tw/
+               http://www.ite.com.tw/product_info/file/pc/IT8705F_V.0.4.1.pdf
   * IT8712F
     Prefix: 'it8712'
     Addresses scanned: from Super I/O config space (8 I/O ports)
     Datasheet: Publicly available at the ITE website
-               http://www.ite.com.tw/
+               http://www.ite.com.tw/product_info/file/pc/IT8712F_V0.9.1.pdf
+               http://www.ite.com.tw/product_info/file/pc/Errata%20V0.1%20for%20IT8712F%20V0.9.1.pdf
+               http://www.ite.com.tw/product_info/file/pc/IT8712F_V0.9.3.pdf
   * IT8716F/IT8726F
     Prefix: 'it8716'
     Addresses scanned: from Super I/O config space (8 I/O ports)
@@ -90,14 +92,13 @@ upper VID bits share their pins with voltage inputs (in5 and in6) so you
 can't have both on a given board.
 
 The IT8716F, IT8718F and later IT8712F revisions have support for
-2 additional fans. They are supported by the driver for the IT8716F and
-IT8718F but not for the IT8712F
+2 additional fans. The additional fans are supported by the driver.
 
 The IT8716F and IT8718F, and late IT8712F and IT8705F also have optional
 16-bit tachometer counters for fans 1 to 3. This is better (no more fan
 clock divider mess) but not compatible with the older chips and
-revisions. For now, the driver only uses the 16-bit mode on the
-IT8716F and IT8718F.
+revisions. The 16-bit tachometer mode is enabled by the driver when one
+of the above chips is detected.
 
 The IT8726F is just bit enhanced IT8716F with additional hardware
 for AMD power sequencing. Therefore the chip will appear as IT8716F
diff --git a/Documentation/hwmon/w83627hf b/Documentation/hwmon/w83627hf
index 880a59f53da9..6ee36dbafd64 100644
--- a/Documentation/hwmon/w83627hf
+++ b/Documentation/hwmon/w83627hf
@@ -40,10 +40,6 @@ Module Parameters
   (default is 1)
   Use 'init=0' to bypass initializing the chip.
   Try this if your computer crashes when you load the module.
-* reset: int
-  (default is 0)
-  The driver used to reset the chip on load, but does no more. Use
-  'reset=1' to restore the old behavior. Report if you need to do this.
 
 Description
 -----------
diff --git a/Documentation/hwmon/w83791d b/Documentation/hwmon/w83791d
index f153b2f6d62c..a67d3b7a7098 100644
--- a/Documentation/hwmon/w83791d
+++ b/Documentation/hwmon/w83791d
@@ -22,6 +22,7 @@ Credits:
 
 Additional contributors:
     Sven Anders <anders@anduras.de>
+    Marc Hulsman <m.hulsman@tudelft.nl>
 
 Module Parameters
 -----------------
@@ -67,9 +68,8 @@ on until the temperature falls below the Hysteresis value.
 
 Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
 triggered if the rotation speed has dropped below a programmable limit. Fan
-readings can be divided by a programmable divider (1, 2, 4, 8 for fan 1/2/3
-and 1, 2, 4, 8, 16, 32, 64 or 128 for fan 4/5) to give the readings more
-range or accuracy.
+readings can be divided by a programmable divider (1, 2, 4, 8, 16,
+32, 64 or 128 for all fans) to give the readings more range or accuracy.
 
 Voltage sensors (also known as IN sensors) report their values in millivolts.
 An alarm is triggered if the voltage has crossed a programmable minimum
diff --git a/Documentation/video4linux/gspca.txt b/Documentation/video4linux/gspca.txt
index bcaf4ab383be..78a863ab8a5a 100644
--- a/Documentation/video4linux/gspca.txt
+++ b/Documentation/video4linux/gspca.txt
@@ -226,6 +226,7 @@ sonixj		0c45:6130	Sonix Pccam
 sonixj          0c45:6138       Sn9c120 Mo4000
 sonixj          0c45:613b       Surfer SN-206
 sonixj          0c45:613c       Sonix Pccam168
+sonixj          0c45:6143       Sonix Pccam168
 sunplus         0d64:0303       Sunplus FashionCam DXG
 etoms           102c:6151       Qcam Sangha CIF
 etoms           102c:6251       Qcam xxxxxx VGA