12 files changed, 0 insertions, 2751 deletions
diff --git a/Documentation/cdrom/00-INDEX b/Documentation/cdrom/00-INDEX
index 916dafe29d3f..433edf23dc49 100644
--- a/Documentation/cdrom/00-INDEX
+++ b/Documentation/cdrom/00-INDEX
@@ -2,32 +2,10 @@
        - this file (info on CD-ROMs and Linux)
 Makefile
        - only used to generate TeX output from the documentation.
-aztcd
-        - info on Aztech/Orchid/Okano/Wearnes/Conrad/CyCDROM driver.
 cdrom-standard.tex
        - LaTeX document on standardizing the CD-ROM programming interface.
-cdu31a
-        - info on the Sony CDU31A/CDU33A CD-ROM driver.
-cm206
-        - info on the Philips/LMS cm206/cm260 CD-ROM driver.
-gscd
-        - info on the Goldstar R420 CD-ROM driver.
 ide-cd
        - info on setting up and using ATAPI (aka IDE) CD-ROMs.
-isp16
-        - info on the CD-ROM interface on ISP16, MAD16 or Mozart sound card.
-mcd
-        - info on limitations of standard Mitsumi CD-ROM driver.
-mcdx
-        - info on improved Mitsumi CD-ROM driver.
-optcd
-        - info on the Optics Storage 8000 AT CD-ROM driver
 packet-writing.txt
        - Info on the CDRW packet writing module
-sbpcd
-        - info on the SoundBlaster/Panasonic CD-ROM interface driver.
-sjcd
-        - info on the SANYO CDR-H94A CD-ROM interface driver.
-sonycd535
-        - info on the Sony CDU-535 (and 531) CD-ROM driver.
diff --git a/Documentation/cdrom/aztcd b/Documentation/cdrom/aztcd
deleted file mode 100644
index 6bf0290ef7ce..000000000000
--- a/Documentation/cdrom/aztcd
+++ /dev/null
@@ -1,822 +0,0 @@
-$Id: README.aztcd,v 2.60 1997/11/29 09:51:25 root Exp root $
-          Readme-File Documentation/cdrom/aztcd
-                                for 
-             AZTECH CD-ROM CDA268-01A, ORCHID CD-3110,
-      OKANO/WEARNES CDD110, CONRAD TXC, CyCDROM CR520, CR540
-                           CD-ROM Drives 
-                       Version 2.6 and newer
-                   (for other drives see 6.-8.)
-NOTE: THIS DRIVER WILL WORK WITH THE CD-ROM DRIVES LISTED, WHICH HAVE
-      A PROPRIETARY INTERFACE (implemented on a sound card or on an
-      ISA-AT-bus card). 
-      IT WILL DEFINITELY NOT WORK WITH CD-ROM DRIVES WITH *IDE*-INTERFACE,
-      such as the Aztech CDA269-031SE !!! (The only known exceptions are
-      'faked' IDE drives like the CyCDROM CR520ie which work with aztcd
-      under certain conditions, see 7.). IF YOU'RE USING A CD-ROM DRIVE
-      WITH IDE-INTERFACE, SOMETIMES ALSO CALLED ATAPI-COMPATIBLE, PLEASE 
-      USE THE ide-cd.c DRIVER, WRITTEN BY MARK LORD AND SCOTT SNYDER !
-      THE STANDARD-KERNEL 1.2.x NOW ALSO SUPPORTS IDE-CDROM-DRIVES, SEE THE
-      HARDDISK (!) SECTION OF make config, WHEN COMPILING A NEW KERNEL!!!
----------------------------------------------------------------------------
-Contents of this file:
-                         1.  NOTE
-                         2.  INSTALLATION
-                         3.  CONFIGURING YOUR KERNEL
-                         4.  RECOMPILING YOUR KERNEL
-                         4.1   AZTCD AS A RUN-TIME LOADABLE MODULE
-                         4.2   CDROM CONNECTED TO A SOUNDCARD
-                         5.  KNOWN PROBLEMS, FUTURE DEVELOPMENTS
-                         5.1   MULTISESSION SUPPORT
-                         5.2   STATUS RECOGNITION
-                         5.3   DOSEMU's CDROM SUPPORT
-                         6.  BUG REPORTS
-                         7.  OTHER DRIVES
-                         8.  IF YOU DON'T SUCCEED ... DEBUGGING  
-                         9.  TECHNICAL HISTORY OF THE DRIVER
-                        10.  ACKNOWLEDGMENTS
-                        11.  PROGRAMMING ADD ONS: CDPLAY.C
-                        APPENDIX: Source code of cdplay.c
----------------------------------------------------------------------------
-1. NOTE 
-This software has been successfully in alpha and beta test and is part of
-the standard kernel since kernel 1.1.8x since December 1994. It works with
-AZTECH CDA268-01A, ORCHID CDS-3110, ORCHID/WEARNES CDD110 and CONRAD TXC 
-(Nr.99 31 23 -series 04) and has proven to be stable with kernel 
-versions 1.0.9 and newer. But with any software there still may be bugs in it. 
-So if you encounter problems, you are invited to help us improve this software. 
-Please send me a detailed bug report (see chapter BUG REPORTS). You are also 
-invited in helping us to increase the number of drives, which are supported.
-Please read the README-files carefully and always keep a backup copy of your 
-old kernel, in order to reboot if something goes wrong!
-2. INSTALLATION
-The driver consists of a header file 'aztcd.h', which normally should reside 
-in /usr/src/linux/drivers/cdrom and the source code 'aztcd.c', which normally 
-resides in the same place. It uses /dev/aztcd (/dev/aztcd0 in some distri-
-butions), which must be a valid block device with major number 29 and reside 
-in directory /dev. To mount a CD-ROM, your kernel needs to have the ISO9660-
-filesystem support included.
-PLEASE NOTE: aztcd.c has been developed in parallel to the linux kernel,
-which had and is having many major and minor changes which are not backward
-compatible. Quite definitely aztcd.c version 1.80 and newer will NOT work
-in kernels older than 1.3.33. So please always use the most recent version
-of aztcd.c with the appropriate linux-kernel.
-3.  CONFIGURING YOUR KERNEL
-If your kernel is already configured for using the AZTECH driver you will
-see the following message while Linux boots:
-    Aztech CD-ROM Init: DriverVersion=<version number> BaseAddress=<baseaddress>
-    Aztech CD-ROM Init: FirmwareVersion=<firmware version id of your I/O-card>>>
-    Aztech CD-ROM Init: <drive type> detected
-    Aztech CD-ROM Init: End
-If the message looks different and you are sure to have a supported drive,
-it may have a different base address. The Aztech driver does look for the 
-CD-ROM drive at the base address specified in aztcd.h at compile time. This 
-address can be overwritten by boot parameter aztcd=....You should reboot and 
-start Linux with boot parameter aztcd=<base address>, e.g. aztcd=0x320. If 
-you do not know the base address, start your PC with DOS and look at the boot 
-message of your CD-ROM's DOS driver. If that still does not help, use boot
-parameter aztcd=<base address>,0x79 , this tells aztcd to try a little harder.
-aztcd may be configured to use autoprobing the base address by recompiling
-it (see chapter 4.).
-If the message looks correct, as user 'root' you should be able to mount the 
-drive by
-          mount -t iso9660 -r /dev/aztcd0 /mnt
-and use it as any other filesystem. (If this does not work, check if
-/dev/aztcd0 and /mnt do exist and create them, if necessary by doing
-      mknod /dev/aztcd0 b 29 0
-      mkdir /mnt                       
-If you still get a different message while Linux boots or when you get the 
-message, that the ISO9660-filesystem is not supported by your kernel, when
-you try to mount the CD-ROM drive, you have to recompile your kernel.
-If you do *not* have an Aztech/Orchid/Okano/Wearnes/TXC drive and want to 
-bypass drive detection during Linux boot up, start with boot parameter aztcd=0.
-Most distributions nowadays do contain a boot disk image containing aztcd.
-Please note, that this driver will not work with IDE/ATAPI drives! With these 
-you must use ide-cd.c instead.
-4. RECOMPILING YOUR KERNEL
-If your kernel is not yet configured for the AZTECH driver and the ISO9660-
-filesystem, you have to recompile your kernel: 
- Edit aztcd.h to set the I/O-address to your I/O-Base address (AZT_BASE_ADDR), 
-  the driver does not use interrupts or DMA, so if you are using an AZTECH
-  CD268, an ORCHID CD-3110 or ORCHID/WEARNES CDD110 that's the only item you 
-  have to set up. If you have a soundcard, read chapter 4.2.
-  Users of other drives should read chapter OTHER DRIVES of this file.
-  You also can configure that address by kernel boot parameter aztcd=... 
- aztcd may be configured to use autoprobing the base address by setting
-  AZT_BASE_ADDR to '-1'. In that case aztcd probes the addresses listed 
-  under AZT_BASE_AUTO. But please remember, that autoprobing always may 
-  incorrectly influence other hardware components too!
- There are some other points, which may be configured, e.g. auto-eject the
-  CD when unmounting a drive, tray locking etc., see aztcd.h for details.
- If you're using a linux kernel version prior to 2.1.0, in aztcd.h
-  uncomment the line '#define AZT_KERNEL_PRIOR_2_1'
- Build a new kernel, configure it for 'Aztech/Orchid/Okano/Wearnes support' 
-  (if you want aztcd to be part of the kernel). Do not configure it for
-  'Aztech... support', if you want to use aztcd as a run time loadable module. 
-  But in any case you must have the ISO9660-filesystem included in your
-  kernel.
- Activate the new kernel, normally this is done by running LILO (don't for-
-  get to configure it before and to keep a copy of your old kernel in case
-  something goes wrong!).
- Reboot
- If you've included aztcd in your kernel, you now should see during boot 
-  some messages like
-    Aztech CD-ROM Init: DriverVersion=<version number> BaseAddress=<baseaddress>
-    Aztech CD-ROM Init: FirmwareVersion=<firmware version id of your I/O-card>
-    Aztech CD-ROM Init: <drive type> detected
-    Aztech CD-ROM Init: End
- If you have not included aztcd in your kernel, but want to load aztcd as a 
-  run time loadable module see 4.1. 
- If the message looks correct, as user 'root' you should be able to mount 
-  the drive by
-          mount -t iso9660 -r /dev/aztcd0 /mnt
-  and use it as any other filesystem. (If this does not work, check if
-  /dev/aztcd0 and /mnt do exist and create them, if necessary by doing
-      mknod /dev/aztcd0 b 29 0
-      mkdir /mnt                       
- If this still does not help, see chapters OTHER DRIVES and DEBUGGING.
-4.1 AZTCD AS A RUN-TIME LOADABLE MODULE
-If you do not need aztcd permanently, you can also load and remove the driver
-during runtime via insmod and rmmod. To build aztcd as a loadable module you 
-must configure your kernel for AZTECH module support (answer 'm' when con-
-figuring the kernel). Anyhow, you may run into problems, if the version of 
-your boot kernel is not the same than the source kernel version, from which 
-you create the modules. So rebuild your kernel, if necessary. 
-Now edit the base address of your AZTECH interface card in
-/usr/src/linux/drivers/cdrom/aztcd.h to the appropriate value. 
-aztcd may be configured to use autoprobing the base address by setting
-AZT_BASE_ADDR to '-1'. In that case aztcd probes the addresses listed 
-under AZT_BASE_AUTO. But please remember, that autoprobing always may 
-incorrectly influence other hardware components too!
-There are also some special features which may be configured, e.g. 
-auto-eject a CD when unmounting the drive etc; see aztcd.h for details. 
-Then change to /usr/src/linux and do a 
-                    make modules  
-                    make modules_install
-After that you can run-time load the driver via
-                    insmod /lib/modules/X.X.X/misc/aztcd.o
-and remove it via   rmmod  aztcd.
-If you did not set the correct base address in aztcd.h, you can also supply the
-base address when loading the driver via
-                    insmod /lib/modules/X.X.X/misc/aztcd.o aztcd=<base address>
-Again specifying aztcd=-1 will cause autoprobing.
-If you do not have the iso9660-filesystem in your boot kernel, you also have
-to load it before you can mount the CDROM:
-                    insmod /lib/modules/X.X.X/fs/isofs.o
-The mount procedure works as described in 4. above.
-(In all commands 'X.X.X' is the current linux kernel version number)
-4.2 CDROM CONNECTED TO A SOUNDCARD
-Most soundcards do have a bus interface to the CDROM-drive. In many cases
-this soundcard needs to be configured, before the CDROM can be used. This
-configuration procedure consists of writing some kind of initialization
-data to the soundcard registers. The AZTECH-CDROM driver in the moment does
-only support one type of soundcard (SoundWave32). Users of other soundcards
-should try to boot DOS first and let their DOS drivers initialize the
-soundcard and CDROM, then warm boot (or use loadlin) their PC to start
-Linux.
-Support for the CDROM-interface of SoundWave32-soundcards is directly
-implemented in the AZTECH driver. Please edit linux/drivers/cdrom/aztdc.h,
-uncomment line '#define AZT_SW32' and set the appropriate value for
-AZT_BASE_ADDR and AZT_SW32_BASE_ADDR. This support was tested with an Orchid
-CDS-3110 connected to a SoundWave32.
-If you want your soundcard to be supported, find out, how it needs to be
-configured and mail me (see 6.) the appropriate information. 
-5. KNOWN PROBLEMS, FUTURE DEVELOPMENTS
-5.1 MULTISESSION SUPPORT
-Multisession support for CD's still is a myth. I implemented and tested a basic
-support for multisession and XA CDs, but I still have not enough CDs and appli-
-cations to test it rigorously. So if you'd like to help me, please contact me
-(Email address see below). As of version 1.4 and newer you can enable the 
-multisession support in aztcd.h by setting AZT_MULTISESSION to 1. Doing so 
-will cause the ISO9660-filesystem to deal with multisession CDs, ie. redirect 
-requests to the Table of Contents (TOC) information from the last session, 
-which contains the info of all previous sessions etc.. If you do set 
-AZT_MULTISESSION to 0, you can use multisession CDs anyway. In that case the 
-drive's firmware will do automatic redirection. For the ISO9660-filesystem any 
-multisession CD  will then look like a 'normal' single session CD. But never-
-theless the data of all sessions are viewable and accessible. So with practical-
-ly all real world applications you won't notice the difference. But as future
-applications may make use of advanced multisession features, I've started to
-implement the interface for the ISO9660 multisession interface via ioctl
-CDROMMULTISESSION.
-5.2 STATUS RECOGNITION
-The drive status recognition does not work correctly in all cases. Changing
-a disk or having the door open, when a drive is already mounted, is detected 
-by the Aztech driver itself, but nevertheless causes multiple read attempts
-by the different layers of the ISO9660-filesystem driver, which finally timeout,
-so you have to wait quite a little... But isn't it bad style to change a disk 
-in a mounted drive, anyhow ?!
-The driver uses busy wait in most cases for the drive handshake (macros
-STEN_LOW and DTEN_LOW). I tested with a 486/DX2 at 66MHz and a Pentium at
-60MHz and 90MHz. Whenever you use a much faster machine you are likely to get 
-timeout messages. In that case edit aztcd.h and increase the timeout value 
-AZT_TIMEOUT. 
-For some 'slow' drive commands I implemented waiting with a timer waitqueue
-(macro STEN_LOW_WAIT). If you get this timeout message, you may also edit
-aztcd.h and increase the timeout value AZT_STATUS_DELAY. The waitqueue has
-shown to be a little critical. If you get kernel panic messages, edit aztcd.c
-and substitute STEN_LOW_WAIT by STEN_LOW. Busy waiting with STEN_LOW is more
-stable, but also causes CPU overhead.
-5.3 DOSEMU's CD-ROM SUPPORT
-With release 1.20 aztcd was modified to allow access to CD-ROMS when running
-under dosemu-0.60.0 aztcd-versions before 1.20 are most likely to crash
-Linux, when a CD-ROM is accessed under dosemu. This problem has partly been
-fixed, but still when accessing a directory for the first time the system
-might hang for some 30sec. So be patient, when using dosemu's CD-ROM support
-in combination with aztcd :-) ! 
-This problem has now (July 1995) been fixed by a modification to dosemu's
-CD-ROM driver. The new version came with dosemu-0.60.2, see dosemu's
-README.CDROM.
-6. BUG REPORTS
-Please send detailed bug reports and bug fixes via EMail to
-        Werner.Zimmermann@fht-esslingen.de
-Please include a description of your CD-ROM drive type and interface card, 
-the exact firmware message during Linux bootup, the version number of the 
-AZTECH-CDROM-driver and the Linux kernel version. Also a description of your 
-system's other hardware could be of interest, especially microprocessor type, 
-clock frequency, other interface cards such as soundcards, ethernet adapter, 
-game cards etc..
-I will try to collect the reports and make the necessary modifications from 
-time to time. I may also come back to you directly with some bug fixes and 
-ask you to do further testing and debugging.
-Editors of CD-ROMs are invited to send a 'cooperation' copy of their
-CD-ROMs to the volunteers, who provided the CD-ROM support for Linux. My
-snail mail address for such 'stuff' is
-           Prof. Dr. W. Zimmermann
-           Fachhochschule fuer Technik Esslingen
-           Fachbereich IT
-           Flandernstrasse 101
-           D-73732 Esslingen
-           Germany
-7. OTHER DRIVES
-The following drives ORCHID CDS3110, OKANO CDD110, WEARNES CDD110 and Conrad
-TXC Nr. 993123-series 04 nearly look the same as AZTECH CDA268-01A, especially 
-they seem to use the same command codes. So it was quite simple to make the 
-AZTECH driver work with these drives. 
-Unfortunately I do not have any of these drives available, so I couldn't test
-it myself. In some installations, it seems necessary to initialize the drive 
-with the DOS driver before (especially if combined with a sound card) and then 
-do a warm boot (CTRL-ALT-RESET) or start Linux from DOS, e.g. with 'loadlin'.
-If you do not succeed, read chapter DEBUGGING. Thanks in advance!
-Sorry for the inconvenience, but it is difficult to develop for hardware, 
-which you don't have available for testing. So if you like, please help us.
-If you do have a CyCDROM CR520ie thanks to Hilmar Berger's help your chances
-are good, that it will work with aztcd. The CR520ie is sold as an IDE-drive
-and really is connected to the IDE interface (primary at 0x1F0 or secondary
-at 0x170, configured as slave, not as master). Nevertheless it is not ATAPI
-compatible but still uses Aztech's command codes.
-8. DEBUGGING : IF YOU DON'T SUCCEED, TRY THE FOLLOWING
-reread the complete README file
-make sure, that your drive is hardware configured for 
-    transfer mode: polled
-    IRQ:           not used
-    DMA:           not used
-    Base Address:  something like 300, 320 ...
- You can check this, when you start the DOS driver, which came with your
- drive. By appropriately configuring the drive and the DOS driver you can
- check, whether your drive does operate in this mode correctly under DOS. If
- it does not operate under DOS, it won't under Linux.
- If your drive's base address is something like 0x170 or 0x1F0 (and it is
- not a CyCDROM CR520ie or CR 940ie) you most likely are having an IDE/ATAPI-
- compatible drive, which is not supported by aztcd.c, use ide-cd.c instead.
- Make sure the Base Address is configured correctly in aztcd.h, also make
- sure, that /dev/aztcd0 exists with the correct major number (compare it with
- the entry in file /usr/include/linux/major.h for the Aztech drive). 
-insert a CD-ROM and close the tray
-cold boot your PC (i.e. via the power on switch or the reset button)
-if you start Linux via DOS, e.g. using loadlin, make sure, that the DOS
- driver for the CD-ROM drive is not loaded (comment out the calling lines 
- in DOS' config.sys!)
-look for the aztcd: init message during Linux init and note them exactly
-log in as root and do a mount -t iso9660 /dev/aztcd0 /mnt
-if you don't succeed in the first time, try several times. Try also to open
- and close the tray, then mount again. Please note carefully all commands
- you typed in and the aztcd-messages, which you get.
-if you get an 'Aztech CD-ROM init: aborted' message, read the remarks about
- the version string below.
-If this does not help, do the same with the following differences 
-start DOS before; make now sure, that the DOS driver for the CD-ROM is 
- loaded under DOS (i.e. uncomment it again in config.sys)
-warm boot your PC (i.e. via CTRL-ALT-DEL)
- if you have it, you can also start via loadlin (try both).
- ...
- Again note all commands and the aztcd-messages.
-If you see STEN_LOW or STEN_LOW_WAIT error messages, increase the timeout
-values.
-If this still does not help, 
-look in aztcd.c for the lines  #if 0
-                                #define AZT_TEST1
-                                ...
-                                #endif
- and substitute '#if 0' by '#if 1'.
-recompile your kernel and repeat the above two procedures. You will now get 
- a bundle of debugging messages from the driver. Again note your commands
- and the appropriate messages. If you have syslogd running, these messages
- may also be found in syslogd's kernel log file. Nevertheless in some
- installations syslogd does not yet run, when init() is called, thus look for
- the aztcd-messages during init, before the login-prompt appears.
- Then look in aztcd.c, to find out, what happened. The normal calling sequence 
- is: aztcd_init() during Linux bootup procedure init()
- after doing a 'mount -t iso9660 /dev/aztcd0 /mnt' the normal calling sequence is
-     aztcd_open()    -> Status 2c after cold reboot with CDROM or audio CD inserted
-                     -> Status 8  after warm reboot with CDROM inserted          
-                     -> Status 2e after cold reboot with no disk, closed tray
-                     -> Status 6e after cold reboot, mount with door open
-     aztUpdateToc()
-     aztGetDiskInfo()
-     aztGetQChannelInfo()   repeated several times
-     aztGetToc()
-     aztGetQChannelInfo()   repeated several times
-     a list of track information
-     do_aztcd_request()  }  
-     azt_transfer()    } repeated several times
-     azt_poll          }
- Check, if there is a difference in the calling sequence or the status flags!
- 
- There are a lot of other messages, eg. the ACMD-command code (defined in
- aztcd.h), status info from the getAztStatus-command and the state sequence of
- the finite state machine in azt_poll(). The most important are the status
- messages, look how they are defined and try to understand, if they make
- sense in the context where they appear. With a CD-ROM inserted the status 
- should always be 8, except in aztcd_open(). Try to open the tray, insert an
- audio disk, insert no disk or reinsert the CD-ROM and check, if the status
- bits change accordingly. The status bits are the most likely point, where 
- the drive manufacturers may implement changes.
-            
-If you still don't succeed, a good point to start is to look in aztcd.c in 
-function aztcd_init, where the drive should be detected during init. Do the
-following:
-reboot the system with boot parameter 'aztcd=<your base address>,0x79'. With
- parameter 0x79 most of the drive version detection is bypassed. After that 
- you should see the complete version string including leading and trailing 
- blanks during init. 
- Now adapt the statement
-      if ((result[1]=='A')&&(result[2]=='Z' ...)
- in aztcd_init() to exactly match the first 3 or 4 letters you have seen.
-Another point is the 'smart' card detection feature in aztcd_init(). Normally
- the CD-ROM drive is ready, when aztcd_init is trying to read the version
- string and a time consuming ACMD_SOFT_RESET command can be avoided. This is
- detected by looking, if AFL_OP_OK can be read correctly. If the CD-ROM drive 
- hangs in some unknown state, e.g. because of an error before a warm start or 
- because you first operated under DOS, even the version string may be correct, 
- but the following commands will not. Then change the code in such a way, 
- that the ACMD_SOFT_RESET is issued in any case, by substituting the
- if-statement 'if ( ...=AFL_OP_OK)' by 'if (1)'.
-If you succeed, please mail me the exact version string of your drive and
-the code modifications, you have made together with a short explanation.
-If you don't succeed, you may mail me the output of the debugging messages.
-But remember, they are only useful, if they are exact and complete and you
-describe in detail your hardware setup and what you did (cold/warm reboot,
-with/without DOS, DOS-driver started/not started, which Linux-commands etc.)
-9. TECHNICAL HISTORY OF THE DRIVER
-The AZTECH-Driver is a rework of the Mitsumi-Driver. Four major items had to
-be reworked:
-a) The Mitsumi drive does issue complete status information acknowledging
-each command, the Aztech drive does only signal that the command was
-processed. So whenever the complete status information is needed, an extra
-ACMD_GET_STATUS command is issued. The handshake procedure for the drive
-can be found in the functions aztSendCmd(), sendAztCmd() and getAztStatus().
-b) The Aztech Drive does not have a ACMD_GET_DISK_INFO command, so the
-necessary info about the number of tracks (firstTrack, lastTrack), disk
-length etc. has to be read from the TOC in the lead in track (see function
-aztGetDiskInfo()).
-c) Whenever data is read from the drive, the Mitsumi drive is started with a
-command to read an indefinite (0xffffff) number of sectors. When the appropriate 
-number of sectors is read, the drive is stopped by a ACDM_STOP command. This
-does not work with the Aztech drive. I did not find a way to stop it. The
-stop and pause commands do only work in AUDIO mode but not in DATA mode.
-Therefore I had to modify the 'finite state machine' in function azt_poll to
-only read a certain number of sectors and then start a new read on demand. As I 
-have not completely understood, how the buffer/caching scheme of the Mitsumi 
-driver was implemented, I am not sure, if I have covered all cases correctly, 
-whenever you get timeout messages, the bug is most likely to be in that
-function azt_poll() around switch(cmd) .... case ACD_S_DATA. 
-d) I did not get information about changing drive mode. So I doubt, that the
-code around function azt_poll() case AZT_S_MODE does work. In my test I have
-not been able to switch to reading in raw mode. For reading raw mode, Aztech
-uses a different command than for cooked mode, which I only have implemen-
-ted in the ioctl-section but not in the section which is used by the ISO9660. 
-The driver was developed on an AST PC with Intel 486/DX2, 8MB RAM, 340MB IDE 
-hard disk and on an AST PC with Intel Pentium 60MHz, 16MB RAM, 520MB IDE 
-running Linux kernel version 1.0.9 from the LST 1.8 Distribution. The kernel 
-was compiled with gcc.2.5.8. My CD-ROM drive is an Aztech CDA268-01A. My
-drive says, that it has Firmware Version AZT26801A1.3. It came with an ISA-bus
-interface card and works with polled I/O without DMA and without interrupts.
-The code for all other drives was 'remote' tested and debugged by a number of 
-volunteers on the Internet.
-Points, where I feel that possible problems might be and all points where I 
-did not completely understand the drive's behaviour or trust my own code are 
-marked with /*???*/ in the source code. There are also some parts in the 
-Mitsumi driver, where I did not completely understand their code.
-10. ACKNOWLEDGMENTS
-Without the help of P.Bush, Aztech, who delivered technical information
-about the Aztech Drive and without the help of E.Moenkeberg, GWDG, who did a
-great job in analyzing the command structure of various CD-ROM drives, this
-work would not have been possible. E.Moenkeberg was also a great help in 
-making the software 'kernel ready' and in answering many of the CDROM-related 
-questions in the newsgroups. He really is *the* Linux CD-ROM guru. Thanks 
-also to all the guys on the Internet, who collected valuable technical 
-information about CDROMs. 
-Joe Nardone (joe@access.digex.net) was a patient tester even for my first
-trial, which was more than slow, and made suggestions for code improvement.
-Especially the 'finite state machine' azt_poll() was rewritten by Joe to get
-clean C code and avoid the ugly 'gotos', which I copied from mcd.c.
-Robby Schirmer (schirmer@fmi.uni-passau.de) tested the audio stuff (ioctls) 
-and suggested a lot of patches for them.
-Joseph Piskor and Peter Nugent were the first users with the ORCHID CD3110
-and also were very patient with the problems which occurred.
-Reinhard Max delivered the information for the CDROM-interface of the
-SoundWave32 soundcards.
-Jochen Kunz and Olaf Kaluza delivered the information for supporting Conrad's 
-TXC drive.
-Hilmar Berger delivered the patches for supporting CyCDROM CR520ie.
-Anybody, who is interested in these items should have a look at 'ftp.gwdg.de',
-directory 'pub/linux/cdrom' and at 'ftp.cdrom.com', directory 'pub/cdrom'.
-11. PROGRAMMING ADD ONs: cdplay.c
-You can use the ioctl-functions included in aztcd.c in your own programs. As
-an example on how to do this, you will find a tiny CD Player for audio CDs 
-named 'cdplay.c'. It allows you to play audio CDs. You can play a specified 
-track, pause and resume or skip tracks forward and backwards. If you quit the 
-program without stopping the  drive, playing is continued. You can also 
-(mis)use cdplay to read and hexdump data disks. You can find the code in the 
-APPENDIX of this file, which you should cut out with an editor and store in a 
-separate file 'cdplay.c'. To compile it and make it executable, do
-  gcc -s -Wall -O2 -L/usr/lib cdplay.c -o /usr/local/bin/cdplay # compiles it
-  chmod +755 /usr/local/bin/cdplay                              # makes it executable
-  ln -s /dev/aztcd0 /dev/cdrom                                  # creates a link
-   (for /usr/lib substitute the top level directory, where your include files 
-    reside,  and for /usr/local/bin the directory, where you want the executable 
-    binary to reside )
-You have to set the correct permissions for cdplay *and* for /dev/mcd0 or
-/dev/aztcd0 in order to use it. Remember, that you should not have /dev/cdrom 
-mounted, when you're playing audio CDs. 
-This program is just a hack for testing the ioctl-functions in aztcd.c. I will 
-not maintain it, so if you run into problems, discard it or have a look into 
-the source code 'cdplay.c'. The program does only contain a minimum of user 
-protection and input error detection. If you use the commands in the wrong 
-order or if you try to read a CD at wrong addresses, you may get error messages
-or even hang your machine. If you get STEN_LOW, STEN_LOW_WAIT or segment violation 
-error messages when using cdplay, after that, the system might not be stable 
-any more, so you'd better reboot. As the ioctl-functions run in kernel mode,
-most normal Linux-multitasking protection features do not work. By using
-uninitialized 'wild' pointers etc., it is easy to write to other users' data 
-and program areas, destroy kernel tables etc.. So if you experiment with ioctls
-as always when you are doing systems programming and kernel hacking, you
-should have a backup copy of your system in a safe place (and you also
-should try restoring from a backup copy first)!
-A reworked and improved version called 'cdtester.c', which has yet more
-features for testing CDROM-drives can be found in
-Documentation/cdrom/sbpcd, written by E.Moenkeberg.
-Werner Zimmermann
-Fachhochschule fuer Technik Esslingen
-(EMail: Werner.Zimmermann@fht-esslingen.de)
-October, 1997
---------------------------------------------------------------------------
-APPENDIX: Source code of cdplay.c
-/* Tiny Audio CD Player
-   Copyright 1994, 1995, 1996 Werner Zimmermann (Werner.Zimmermann@fht-esslingen.de)
-This program originally was written to test the audio functions of the
-AZTECH.CDROM-driver, but it should work with every CD-ROM drive. Before 
-using it, you should set a symlink from /dev/cdrom to your real CDROM
-device.
-The GNU General Public License applies to this program.
-History:  V0.1  W.Zimmermann: First release. Nov. 8, 1994
-          V0.2  W.Zimmermann: Enhanced functionality. Nov. 9, 1994
-          V0.3  W.Zimmermann: Additional functions. Nov. 28, 1994          
-          V0.4  W.Zimmermann: fixed some bugs. Dec. 17, 1994
-          V0.5  W.Zimmermann: clean 'scanf' commands without compiler warnings
-                              Jan. 6, 1995
-          V0.6  W.Zimmermann: volume control (still experimental). Jan. 24, 1995
-          V0.7  W.Zimmermann: read raw modified. July 26, 95
-*/
-#include <stdio.h>
-#include <ctype.h>
-#include <sys/ioctl.h>
-#include <sys/types.h>
-#include <fcntl.h>
-#include <unistd.h>
-#include <linux/cdrom.h>
-#include <linux/../../drivers/cdrom/aztcd.h>
-void help(void)
-{ printf("Available Commands:  STOP         s      EJECT/CLOSE  e       QUIT         q\n");
-  printf("                     PLAY TRACK   t      PAUSE        p       RESUME       r\n");
-  printf("                     NEXT TRACK   n      REPEAT LAST  l       HELP         h\n");
-  printf("                     SUB CHANNEL  c      TRACK INFO   i       PLAY AT      a\n");
-  printf("                     READ         d      READ RAW     w       VOLUME       v\n");
-}
-int main(void)
-{ int handle;
-  unsigned char command=' ', ini=0, first=1, last=1;
-  unsigned int cmd, i,j,k, arg1,arg2,arg3;
-  struct cdrom_ti       ti;
-  struct cdrom_tochdr   tocHdr;
-  struct cdrom_subchnl  subchnl;
-  struct cdrom_tocentry entry;
-  struct cdrom_msf      msf;
-  union  { struct cdrom_msf msf;
-           unsigned char buf[CD_FRAMESIZE_RAW];
-         } azt;
-  struct cdrom_volctrl  volctrl;
-  printf("\nMini-Audio CD-Player V0.72   (C) 1994,1995,1996  W.Zimmermann\n");
-  handle=open("/dev/cdrom",O_RDWR);
-  ioctl(handle,CDROMRESUME);
-  
-  if (handle<=0) 
-    { printf("Drive Error: already playing, no audio disk, door open\n");
-      printf("             or no permission (you must be ROOT in order to use this program)\n");
-    }
-  else
-    { help();
-      while (1)
-        { printf("Type command (h = help):  ");
-          scanf("%s",&command); 
-          switch (command)
-            { case 'e':   cmd=CDROMEJECT;
-                          ioctl(handle,cmd);
-                          break;  
-              case 'p':   if (!ini)
-                             { printf("Command not allowed - play track first\n");
-                             }
-                          else
-                             { cmd=CDROMPAUSE;
-                               if (ioctl(handle,cmd)) printf("Drive Error\n");
-                             }
-                          break;
-              case 'r':   if (!ini)
-                             { printf("Command not allowed - play track first\n");
-                             }
-                          else
-                             { cmd=CDROMRESUME;
-                               if (ioctl(handle,cmd)) printf("Drive Error\n");
-                             }
-                          break;
-              case 's':   cmd=CDROMPAUSE;
-                          if (ioctl(handle,cmd)) printf("Drive error or already stopped\n");
-                          cmd=CDROMSTOP;
-                          if (ioctl(handle,cmd)) printf("Drive error\n");
-                          break;
-              case 't':   cmd=CDROMREADTOCHDR;
-                          if (ioctl(handle,cmd,&tocHdr)) printf("Drive Error\n");
-                          first=tocHdr.cdth_trk0;
-                          last= tocHdr.cdth_trk1;
-                          if ((first==0)||(first>last))
-                            { printf ("--could not read TOC\n");
-                            }
-                          else
-                            { printf("--first track: %d   --last track: %d   --enter track number: ",first,last);
-                              cmd=CDROMPLAYTRKIND;
-                              scanf("%i",&arg1);
-                              ti.cdti_trk0=arg1;
-                              if (ti.cdti_trk0<first) ti.cdti_trk0=first;
-                              if (ti.cdti_trk0>last)  ti.cdti_trk0=last;
-                              ti.cdti_ind0=0;
-                              ti.cdti_trk1=last;
-                              ti.cdti_ind1=0;
-                              if (ioctl(handle,cmd,&ti)) printf("Drive Error\n");
-                              ini=1;
-                            } 
-                          break;
-              case 'n':   if (!ini++) 
-                            { if (ioctl(handle,CDROMREADTOCHDR,&tocHdr)) printf("Drive Error\n");
-                              first=tocHdr.cdth_trk0;
-                              last= tocHdr.cdth_trk1;
-                              ti.cdti_trk0=first-1;
-                            }
-                          if ((first==0)||(first>last))
-                            { printf ("--could not read TOC\n");
-                            }
-                          else
-                            { cmd=CDROMPLAYTRKIND;
-                              if (++ti.cdti_trk0 > last)  ti.cdti_trk0=last;
-                              ti.cdti_ind0=0;
-                              ti.cdti_trk1=last;
-                              ti.cdti_ind1=0;
-                              if (ioctl(handle,cmd,&ti)) printf("Drive Error\n");
-                              ini=1;
-                            }
-                          break;
-              case 'l':   if (!ini++)
-                            { if (ioctl(handle,CDROMREADTOCHDR,&tocHdr)) printf("Drive Error\n");
-                              first=tocHdr.cdth_trk0;
-                              last= tocHdr.cdth_trk1;
-                              ti.cdti_trk0=first+1;
-                            }
-                          if ((first==0)||(first>last))
-                            { printf ("--could not read TOC\n");
-                            }
-                          else
-                            { cmd=CDROMPLAYTRKIND;
-                              if (--ti.cdti_trk0 < first) ti.cdti_trk0=first;
-                              ti.cdti_ind0=0;
-                              ti.cdti_trk1=last;
-                              ti.cdti_ind1=0;
-                              if (ioctl(handle,cmd,&ti)) printf("Drive Error\n");
-                              ini=1;
-                            }  
-                          break;
-              case 'c':   subchnl.cdsc_format=CDROM_MSF;
-                          if (ioctl(handle,CDROMSUBCHNL,&subchnl)) 
-                            printf("Drive Error\n");
-                          else
-                            { printf("AudioStatus:%s   Track:%d  Mode:%d   MSF=%d:%d:%d\n", \
-                              subchnl.cdsc_audiostatus==CDROM_AUDIO_PLAY ? "PLAYING":"NOT PLAYING",\
-                              subchnl.cdsc_trk,subchnl.cdsc_adr, \
-                              subchnl.cdsc_absaddr.msf.minute, subchnl.cdsc_absaddr.msf.second, \
-                              subchnl.cdsc_absaddr.msf.frame);
-                            }
-                          break;              
-              case 'i':   if (!ini)
-                            { printf("Command not allowed - play track first\n");
-                            }
-                          else
-                            { cmd=CDROMREADTOCENTRY;
-                              printf("Track No.: ");
-                              scanf("%d",&arg1);
-                              entry.cdte_track=arg1;
-                              if (entry.cdte_track<first) entry.cdte_track=first;
-                              if (entry.cdte_track>last)  entry.cdte_track=last;
-                              entry.cdte_format=CDROM_MSF;
-                              if (ioctl(handle,cmd,&entry)) 
-                               { printf("Drive error or invalid track no.\n");
-                               }
-                              else
-                               { printf("Mode %d Track, starts at %d:%d:%d\n", \
-                               entry.cdte_adr,entry.cdte_addr.msf.minute, \
-                               entry.cdte_addr.msf.second,entry.cdte_addr.msf.frame);
-                               }
-                            }
-                          break;
-              case 'a':   cmd=CDROMPLAYMSF;
-                          printf("Address (min:sec:frame)  ");
-                          scanf("%d:%d:%d",&arg1,&arg2,&arg3);
-                          msf.cdmsf_min0  =arg1;
-                          msf.cdmsf_sec0  =arg2;
-                          msf.cdmsf_frame0=arg3;
-                          if (msf.cdmsf_sec0  > 59) msf.cdmsf_sec0  =59;
-                          if (msf.cdmsf_frame0> 74) msf.cdmsf_frame0=74;
-                          msf.cdmsf_min1=60;
-                          msf.cdmsf_sec1=00;
-                          msf.cdmsf_frame1=00;
-                          if (ioctl(handle,cmd,&msf)) 
-                           { printf("Drive error or invalid address\n");
-                           }
-                          break;
-#ifdef AZT_PRIVATE_IOCTLS /*not supported by every CDROM driver*/
-              case 'd':   cmd=CDROMREADCOOKED;
-                          printf("Address (min:sec:frame)  ");
-                          scanf("%d:%d:%d",&arg1,&arg2,&arg3);
-                          azt.msf.cdmsf_min0  =arg1;
-                          azt.msf.cdmsf_sec0  =arg2;
-                          azt.msf.cdmsf_frame0=arg3;
-                          if (azt.msf.cdmsf_sec0  > 59) azt.msf.cdmsf_sec0  =59;
-                          if (azt.msf.cdmsf_frame0> 74) azt.msf.cdmsf_frame0=74;
-                          if (ioctl(handle,cmd,&azt.msf)) 
-                           { printf("Drive error, invalid address or unsupported command\n");
-                           }
-                          k=0;
-                          getchar();
-                          for (i=0;i<128;i++)
-                           { printf("%4d:",i*16);
-                             for (j=0;j<16;j++)
-                               { printf("%2x ",azt.buf[i*16+j]);
-                               }
-                             for (j=0;j<16;j++)
-                               { if (isalnum(azt.buf[i*16+j])) 
-                                   printf("%c",azt.buf[i*16+j]);
-                                 else
-                                   printf(".");
-                               }
-                             printf("\n"); 
-                             k++;
-                             if (k>=20)
-                              { printf("press ENTER to continue\n");
-                                getchar();
-                                k=0;
-                              }
-                           } 
-                          break;
-              case 'w':   cmd=CDROMREADRAW;
-                          printf("Address (min:sec:frame)  ");
-                          scanf("%d:%d:%d",&arg1,&arg2,&arg3);
-                          azt.msf.cdmsf_min0  =arg1;
-                          azt.msf.cdmsf_sec0  =arg2;
-                          azt.msf.cdmsf_frame0=arg3;                          
-                          if (azt.msf.cdmsf_sec0  > 59) azt.msf.cdmsf_sec0  =59;
-                          if (azt.msf.cdmsf_frame0> 74) azt.msf.cdmsf_frame0=74;
-                          if (ioctl(handle,cmd,&azt)) 
-                           { printf("Drive error, invalid address or unsupported command\n");
-                           }
-                          k=0;
-                          for (i=0;i<147;i++)
-                           { printf("%4d:",i*16);
-                             for (j=0;j<16;j++)
-                               { printf("%2x ",azt.buf[i*16+j]);
-                               }
-                             for (j=0;j<16;j++)
-                               { if (isalnum(azt.buf[i*16+j])) 
-                                   printf("%c",azt.buf[i*16+j]);
-                                 else
-                                   printf(".");
-                               }
-                             printf("\n"); 
-                             k++;
-                             if (k>=20)
-                              { getchar();
-                                k=0;
-                              }
-                           } 
-                          break;
-#endif
-              case 'v':   cmd=CDROMVOLCTRL;
-                          printf("--Channel 0 Left  (0-255): ");
-                          scanf("%d",&arg1);
-                          printf("--Channel 1 Right (0-255): ");
-                          scanf("%d",&arg2);
-                          volctrl.channel0=arg1;
-                          volctrl.channel1=arg2;
-                          volctrl.channel2=0;
-                          volctrl.channel3=0;
-                          if (ioctl(handle,cmd,&volctrl)) 
-                           { printf("Drive error or unsupported command\n");
-                           }
-                          break;  
-              case 'q':   if (close(handle)) printf("Drive Error: CLOSE\n");
-                          exit(0);
-              case 'h':   help();
-                          break;
-              default:    printf("unknown command\n");
-                          break;
-            }
-       }
-    }
-  return 0;
-}
diff --git a/Documentation/cdrom/cdu31a b/Documentation/cdrom/cdu31a
deleted file mode 100644
index c0667da09c00..000000000000
--- a/Documentation/cdrom/cdu31a
+++ /dev/null
@@ -1,196 +0,0 @@
-                CDU31A/CDU33A Driver Info
-                -------------------------
-Information on the Sony CDU31A/CDU33A CDROM driver for the Linux
-kernel.
-   Corey Minyard (minyard@metronet.com)
-  
-   Colossians 3:17
-Crude Table of Contents
-----------------------
-  Setting Up the Hardware
-  Configuring the Kernel
-  Configuring as a Module
-  Driver Special Features
-  
-This device driver handles Sony CDU31A/CDU33A CDROM drives and
-provides a complete block-level interface as well as an ioctl()
-interface as specified in include/linux/cdrom.h).  With this
-interface, CDROMs can be accessed, standard audio CDs can be played
-back normally, and CD audio information can be read off the drive.
-Note that this will only work for CDU31A/CDU33A drives.  Some vendors
-market their drives as CDU31A compatible.  They lie.  Their drives are
-really CDU31A hardware interface compatible (they can plug into the
-same card).  They are not software compatible.
-Setting Up the Hardware
-----------------------
-The CDU31A driver is unable to safely tell if an interface card is
-present that it can use because the interface card does not announce
-its presence in any way besides placing 4 I/O locations in memory.  It
-used to just probe memory and attempt commands, but Linus wisely asked
-me to remove that because it could really screw up other hardware in
-the system.
-Because of this, you must tell the kernel where the drive interface
-is, what interrupts are used, and possibly if you are on a PAS-16
-soundcard.
-If you have the Sony CDU31A/CDU33A drive interface card, the following
-diagram will help you set it up.  If you have another card, you are on
-your own.  You need to make sure that the I/O address and interrupt is
-not used by another card in the system.  You will need to know the I/O
-address and interrupt you have set.  Note that use of interrupts is
-highly recommended, if possible, it really cuts down on CPU used.
-Unfortunately, most soundcards do not support interrupts for their
-CDROM interfaces.  By default, the Sony interface card comes with
-interrupts disabled.
-   
-        +----------+-----------------+----------------------+
-        |  JP1     |  34 Pin Conn    |                      |
-        |  JP2     +-----------------+                      |
-        |  JP3                                              |
-        |  JP4                                              |
-        |                                                   +--+
-        |                                                   |  +-+
-        |                                                   |  | |  External
-        |                                                   |  | |  Connector
-        |                                                   |  | |
-        |                                                   |  +-+
-        |                                                   +--+
-        |                                                   |
-        |                                          +--------+
-        |                                          |
-        +------------------------------------------+
-   
-      JP1 sets the Base Address, using the following settings:
-   
-        Address         Pin 1           Pin 2
-        -------         -----           -----
-        0x320           Short           Short
-        0x330           Short           Open
-        0x340           Open            Short
-        0x360           Open            Open
-   
-      JP2 and JP3 configure the DMA channel; they must be set the same.
-   
-        DMA             Pin 1           Pin 2           Pin 3
-        ---             -----           -----           -----
-        1               On              Off             On
-        2               Off             On              Off
-        3               Off             Off             On
-   
-      JP4 Configures the IRQ:
-   
-        IRQ     Pin 1           Pin 2           Pin 3           Pin 4
-        ---     -----           -----           -----           -----
-        3       Off             Off             On              Off
-        4       Off             Off*            Off             On
-        5       On              Off             Off             Off
-        6       Off             On              Off             Off
-   
-                  The documentation states to set this for interrupt
-                  4, but I think that is a mistake.
-Note that if you have another interface card, you will need to look at
-the documentation to find the I/O base address.  This is specified to
-the SLCD.SYS driver for DOS with the /B: parameter, so you can look at
-you DOS driver setup to find the address, if necessary.
-Configuring the Kernel
----------------------
-You must tell the kernel where the drive is at boot time.  This can be
-done at the Linux boot prompt, by using LILO, or by using Bootlin.
-Note that this is no substitute for HOWTOs and LILO documentation, if
-you are confused please read those for info on bootline configuration
-and LILO.
-At the linux boot prompt, press the ALT key and add the following line
-after the boot name (you can let the kernel boot, it will tell you the
-default boot name while booting):
-        cdu31a=<base address>,<interrupt>[,PAS]
-The base address needs to have "0x" in front of it, since it is in
-hex.  For instance, to configure a drive at address 320 on interrupt 5,
-use the following:
-        cdu31a=0x320,5
-I use the following boot line:
-        cdu31a=0x1f88,0,PAS
-because I have a PAS-16 which does not support interrupt for the
-CDU31A interface.
-Adding this as an append line at the beginning of the /etc/lilo.conf
-file will set it for lilo configurations.  I have the following as the
-first line in my lilo.conf file:
-        append="cdu31a=0x1f88,0"
-I'm not sure how to set up Bootlin (I have never used it), if someone
-would like to fill in this section please do.
-Configuring as a Module
-----------------------
-The driver supports loading as a module.  However, you must specify
-the boot address and interrupt on the boot line to insmod.  You can't
-use modprobe to load it, since modprobe doesn't support setting
-variables.
-Anyway, I use the following line to load my driver as a module
-  /sbin/insmod /lib/modules/`uname -r`/misc/cdu31a.o cdu31a_port=0x1f88
-You can set the following variables in the driver:
-  cdu31a_port=<I/O address> - sets the base I/O.  If hex, put 0x in
-                              front of it.  This must be specified.
-  cdu31a_irq=<interrupt> - Sets the interrupt number.  Leaving this
-                           off will turn interrupts off.
-Driver Special Features
-----------------------
-This section describes features beyond the normal audio and CD-ROM
-functions of the drive.
-2048 byte buffer mode
-If a disk is mounted with -o block=2048, data is copied straight from
-the drive data port to the buffer.  Otherwise, the readahead buffer
-must be involved to hold the other 1K of data when a 1K block
-operation is done.  Note that with 2048 byte blocks you cannot execute
-files from the CD.
-XA compatibility
-The driver should support XA disks for both the CDU31A and CDU33A.  It
-does this transparently, the using program doesn't need to set it.
-Multi-Session
-A multi-session disk looks just like a normal disk to the user.  Just
-mount one normally, and all the data should be there.  A special
-thanks to Koen for help with this!
-Raw sector I/O
-Using the CDROMREADAUDIO it is possible to read raw audio and data
-tracks.  Both operations return 2352 bytes per sector.  On the data
-tracks, the first 12 bytes is not returned by the drive and the value
-of that data is indeterminate.
diff --git a/Documentation/cdrom/cm206 b/Documentation/cdrom/cm206
deleted file mode 100644
index 810368f4f7c4..000000000000
--- a/Documentation/cdrom/cm206
+++ /dev/null
@@ -1,185 +0,0 @@
-This is the readme file for the driver for the Philips/LMS cdrom drive
-cm206 in combination with the cm260 host adapter card. 
-                                (c) 1995 David A. van Leeuwen
-   
-Changes since version 0.99
--------------------------
- Interfacing to the kernel is routed though an extra interface layer, 
-  cdrom.c. This allows runtime-configurable `behavior' of the cdrom-drive, 
-  independent of the driver. 
-Features since version 0.33
---------------------------
- Full audio support, that is, both  workman, workbone and cdp work
-  now reasonably. Reading TOC still takes some time. xmcd has been
-  reported to run successfully. 
- Made auto-probe code a little better, I hope
-Features since version 0.28
---------------------------
- Full speed transfer rate (300 kB/s).
- Minimum kernel memory usage for buffering (less than 3 kB).
- Multisession support.
- Tray locking.
- Statistics of driver accessible to the user.
- Module support.
- Auto-probing of adapter card's base port and irq line,
-  also configurable at boot time or module load time.
-Decide how you are going to use the driver. There are two
-options:
-   (a) installing the driver as a resident part of the kernel
-   (b) compiling the driver as a loadable module
-   Further, you must decide if you are going to specify the base port
-   address and the interrupt request line of the adapter card cm260 as
-   boot options for (a), module parameters for (b), use automatic
-   probing of these values, or hard-wire your adaptor card's settings
-   into the source code. If you don't care, you can choose 
-   autoprobing, which is the default. In that case you can move on to
-   the next step.
-Compiling the kernel
--------------------
-1) move to /usr/src/linux and do a 
-        make config
-   If you have chosen option (a), answer yes to CONFIG_CM206 and
-   CONFIG_ISO9660_FS.
-   If you have chosen option (b), answer yes to CONFIG_MODVERSIONS
-   and no (!) to CONFIG_CM206 and CONFIG_ISO9660_FS. 
-2) then do a 
-        
-        make clean; make zImage; make modules
-3) do the usual things to install a new image (backup the old one, run
-   `rdev -R zImage 1', copy the new image in place, run lilo).  Might
-   be `make zlilo'.
-Using the driver as a module
----------------------------
-If you will only occasionally use the cd-rom driver, you can choose
-option (b), install as a loadable module. You may have to re-compile
-the module when you upgrade the kernel to a new version. 
-Since version 0.96, much of the functionality has been transferred to
-a generic cdrom interface in the file cdrom.c. The module cm206.o
-depends on cdrom.o. If the latter is not compiled into the kernel,
-you must explicitly load it before cm206.o:
-         insmod /usr/src/linux/modules/cdrom.o
-To install the module, you use the command, as root
-        insmod /usr/src/linux/modules/cm206.o
-You can specify the base address on the command line as well as the irq 
-line to be used, e.g.
-        insmod /usr/src/linux/modules/cm206.o cm206=0x300,11
-The order of base port and irq line doesn't matter; if you specify only
-one, the other will have the value of the compiled-in default.  You
-may also have to install the file-system module `iso9660.o', if you
-didn't compile that into the kernel. 
-Using the driver as part of the kernel
--------------------------------------
-If you have chosen option (a), you can specify the base-port
-address and irq on the lilo boot command line, e.g.:
-        LILO: linux cm206=0x340,11
-This assumes that your linux kernel image keyword is `linux'. 
-If you specify either IRQ (3--11) or base port (0x300--0x370),
-auto probing is turned off for both settings, thus setting the 
-other value to the compiled-in default.
-Note that you can also put these parameters in the lilo configuration file:
-# linux config
-image = /vmlinuz
-   root = /dev/hda1
-   label = Linux
-   append = "cm206=0x340,11"
-   read-only
-If module parameters and LILO config options don't work
-------------------------------------------------------
-If autoprobing does not work, you can hard-wire the default values
-of the base port address (CM206_BASE) and interrupt request line
-(CM206_IRQ) into the file /usr/src/linux/drivers/cdrom/cm206.h. Change
-the defines of CM206_IRQ and CM206_BASE.
-Mounting the cdrom
------------------
-1) Make sure that the right device is installed in /dev.
-        mknod /dev/cm206cd b 32 0
-2) Make sure there is a mount point, e.g., /cdrom 
-        mkdir /cdrom
-3) mount using a command like this (run as root):
-        mount -rt iso9660 /dev/cm206cd /cdrom
-4) For user-mounts, add a line in /etc/fstab
-        /dev/cm206cd      /cdrom     iso9660    ro,noauto,user
-   This will allow users to give the commands
-        mount /cdrom
-        umount /cdrom
-If things don't work
--------------------
- Try to do a `dmesg' to find out if the driver said anything about
-  what is going wrong during the initialization.
- Try to do a `dd if=/dev/cm206cd | od -tc | less' to read from the
-  CD.
- Look in the /proc directory to see if `cm206' shows up under one of
-  `interrupts', `ioports', `devices' or `modules' (if applicable).
-DISCLAIMER 
---------- 
-I cannot guarantee that this driver works, or that the hardware will
-not be harmed, although I consider it most unlikely. 
-I hope that you'll find this driver in some way useful. 
-                                        David van Leeuwen
-                                        david@tm.tno.nl
-Note for Linux CDROM vendors
-----------------------------
-You are encouraged to include this driver on your Linux CDROM. If
-you do, you might consider sending me a free copy of that cd-rom.
-You can contact me through my e-mail address, david@tm.tno.nl. 
-If this driver is compiled into a kernel to boot off a cdrom, 
-you should actually send me a free copy of that cd-rom. 
-Copyright
---------
-The copyright of the cm206 driver for Linux is 
-    (c) 1995 David A. van Leeuwen
-The driver is released under the conditions of the GNU general public
-license, which can be found in the file COPYING in the root of this
-source tree.
diff --git a/Documentation/cdrom/gscd b/Documentation/cdrom/gscd
deleted file mode 100644
index d01ca36b5c43..000000000000
--- a/Documentation/cdrom/gscd
+++ /dev/null
@@ -1,60 +0,0 @@
-        Goldstar R420 CD-Rom device driver README
-For all kind of other information about the GoldStar R420 CDROM
-and this Linux device driver see the WWW page:
-        http://linux.rz.fh-hannover.de/~raupach        
-      If you are the editor of a Linux CD, you should
-      enable gscd.c within your boot floppy kernel. Please,
-      send me one of your CDs for free.
-This current driver version 0.4a only supports reading data from the disk.
-Currently we have no audio and no multisession or XA support.
-The polling interface is used, no DMA.
-Sometimes the GoldStar R420 is sold in a 'Reveal Multimedia Kit'. This kit's
-drive interface is compatible, too.
-Installation
------------
-Change to '/usr/src/linux/drivers/cdrom' and edit the file 'gscd.h'. Insert
-the i/o address of your interface card.
-The default base address is 0x340. This will work for most applications. 
-Address selection is accomplished by jumpers PN801-1 to PN801-4 on the 
-GoldStar Interface Card.
-Appropriate settings are: 0x300, 0x310, 0x320, 0x330, 0x340, 0x350, 0x360
-0x370, 0x380, 0x390, 0x3A0, 0x3B0, 0x3C0, 0x3D0, 0x3E0, 0x3F0             
-Then go back to '/usr/src/linux/' and 'make config' to build the new
-configuration for your kernel. If you want to use the GoldStar driver
-like a module, don't select 'GoldStar CDROM support'. By the way, you
-have to include the iso9660 filesystem.
-Now start compiling the kernel with 'make zImage'.
-If you want to use the driver as a module, you have to do 'make modules' 
-and 'make modules_install', additionally.
-Install your new kernel as usual - maybe you do it with 'make zlilo'.
-Before you can use the driver, you have to
-   mknod /dev/gscd0 b 16 0
-to create the appropriate device file (you only need to do this once).
-If you use modules, you can try to insert the driver.
-Say: 'insmod /usr/src/linux/modules/gscd.o'
-or:  'insmod /usr/src/linux/modules/gscd.o gscd=<address>'
-The driver should report its results.
-That's it! Mount a disk, i.e. 'mount -rt iso9660 /dev/gscd0 /cdrom'
-Feel free to report errors and suggestions to the following address.
-Be sure, I'm very happy to receive your comments!
- 
-        Oliver Raupach                                Hannover, Juni 1995
-(raupach@nwfs1.rz.fh-hannover.de)
diff --git a/Documentation/cdrom/isp16 b/Documentation/cdrom/isp16
deleted file mode 100644
index cc86533ac9f3..000000000000
--- a/Documentation/cdrom/isp16
+++ /dev/null
@@ -1,100 +0,0 @@
- -- Documentation/cdrom/isp16
-Docs by Eric van der Maarel <H.T.M.v.d.Maarel@marin.nl>
-This is the README for version 0.6 of the cdrom interface on an
-ISP16, MAD16 or Mozart sound card.
-The detection and configuration of this interface used to be included
-in both the sjcd and optcd cdrom driver. Drives supported by these
-drivers came packed with Media Magic's multi media kit, which also
-included the ISP16 card. The idea (thanks Leo Spiekman)
-to move it from these drivers into a separate module and moreover, not to
-rely on the MAD16 sound driver, are as follows:
-duplication of code in the kernel is a waste of resources and should
- be avoided;
-however, kernels and notably those included with Linux distributions
- (cf Slackware 3.0 included version 0.5 of the isp16 configuration
- code included in the drivers) don't always come with sound support
- included. Especially when they already include a bunch of cdrom drivers.
- Hence, the cdrom interface should be configurable _independently_ of
- sound support.
-The ISP16, MAD16 and Mozart sound cards have an OPTi 82C928 or an
-OPTi 82C929 chip.  The interface on these cards should work with
-any cdrom attached to the card, which is 'electrically' compatible
-with Sanyo/Panasonic, Sony or Mitsumi non-ide drives. However, the
-command sets for any proprietary drives may differ
-(and hence may not be supported in the kernel) from these four types.
-For a fact I know the interface works and the way of configuration
-as described in this documentation works in combination with the
-sjcd (in Sanyo/Panasonic compatibility mode) cdrom drivers
-(probably with the optcd (in Sony compatibility mode) as well).
-If you have such an OPTi based sound card and you want to use the
-cdrom interface with a cdrom drive supported by any of the other cdrom
-drivers, it will probably work. Please let me know any experience you
-might have).
-I understand that cards based on the OPTi 82C929 chips may be configured
-(hardware jumpers that is) as an IDE interface. Initialisation of such a
-card in this mode is not supported (yet?).
-The suggestion to configure the ISP16 etc. sound card by booting DOS and 
-do a warm reboot to boot Linux somehow doesn't work, at least not
-on my machine (IPC P90), with the OPTi 82C928 based card.
-Booting the kernel through the boot manager LILO allows the use
-of some command line options on the 'LILO boot:' prompt. At boot time
-press Alt or Shift while the LILO prompt is written on the screen and enter
-any kernel options. Alternatively these options may be used in
-the appropriate section in /etc/lilo.conf. Adding 'append="<cmd_line_options>"'
-will do the trick as well.
-The syntax of 'cmd_line_options' is
-        isp16=[<port>[,<irq>[,<dma>]]][[,]<drive_type>]
-If there is no ISP16 or compatibles detected, there's probably no harm done.
-These options indicate the values that your cdrom drive has been (or will be)
-configured to use.
-Valid values for the base i/o address are:
-  port=0x340,0x320,0x330,0x360
-for the interrupt request number 
-  irq=0,3,5,7,9,10,11
-for the direct memory access line
-  dma=0,3,5,6,7
-and for the type of drive
-  drive_type=noisp16,Sanyo,Panasonic,Sony,Mitsumi.
-Note that these options are case sensitive.
-The values 0 for irq and dma indicate that they are not used, and
-the drive will be used in 'polling' mode. The values 5 and 7 for irq
-should be avoided in order to avoid any conflicts with optional
-sound card configuration.
-The syntax of the command line does not allow the specification of
-irq when there's nothing specified for the base address and no
-specification of dma when there is no specification of irq.
-The value 'noisp16' for drive_type, which may be used as the first
-non-integer option value (e.g. 'isp16=noisp16'), makes sure that probing
-for and subsequent configuration of an ISP16-compatible card is skipped
-all together. This can be useful to overcome possible conflicts which
-may arise while the kernel is probing your hardware.
-The default values are
-  port=0x340
-  irq=0
-  dma=0
-  drive_type=Sanyo
-reflecting my own configuration. The defaults can be changed in
-the file linux/drivers/cdrom/ips16.h.
-The cdrom interface can be configured at run time by loading the
-initialisation driver as a module. In that case, the interface
-parameters can be set by giving appropriate values on the command
-line. Configuring the driver can then be done by the following
-command (assuming you have iso16.o installed in a proper place):
-  insmod isp16.o isp16_cdrom_base=<port> isp16_cdrom_irq=<irq> \
-    isp16_cdrom_dma=<dma> isp16_cdrom_type=<drive_type>
-where port, irq, dma and drive_type can have any of the values mentioned
-above.
-Have fun!
diff --git a/Documentation/cdrom/mcdx b/Documentation/cdrom/mcdx
deleted file mode 100644
index 2bac4b7ff6da..000000000000
--- a/Documentation/cdrom/mcdx
+++ /dev/null
@@ -1,29 +0,0 @@
-If you are using the driver as a module, you can specify your ports and IRQs
-like
- # insmod mcdx.o mcdx=0x300,11,0x304,5
-and so on ("address,IRQ" pairs).
-This will override the configuration in mcdx.h.
-This driver:
-    o   handles XA and (hopefully) multi session CDs as well as
-        ordinary CDs;
-    o   supports up to 5 drives (of course, you'll need free 
-        IRQs, i/o ports and slots);
-    o   plays audio
-This version doesn't support yet:
-    o   shared IRQs (but it seems to be possible - I've successfully
-                connected two drives to the same irq.  So it's `only' a 
-                problem of the driver.)
-This driver never will:
-    o   Read digital audio (i.e. copy directly), due to missing
-        hardware features. 
-heiko@lotte.sax.de
diff --git a/Documentation/cdrom/optcd b/Documentation/cdrom/optcd
deleted file mode 100644
index 6f46c7adb243..000000000000
--- a/Documentation/cdrom/optcd
+++ /dev/null
@@ -1,57 +0,0 @@
-This is the README file for the Optics Storage 8000 AT CDROM device driver.
-This is the driver for the so-called 'DOLPHIN' drive, with the 34-pin
-Sony-compatible interface. For the IDE-compatible Optics Storage 8001
-drive, you will want the ATAPI CDROM driver. The driver also seems to
-work with the Lasermate CR328A. If you have a drive that works with
-this driver, and that doesn't report itself as DOLPHIN, please drop me
-a mail.
-The support for multisession CDs is in ALPHA stage. If you use it,
-please mail me your experiences. Multisession support can be disabled
-at compile time.
-You can find some older versions of the driver at
-      dutette.et.tudelft.nl:/pub/linux/
-and at Eberhard's mirror
-      ftp.gwdg.de:/pub/linux/cdrom/drivers/optics/
-Before you can use the driver, you have to create the device file once:
- # mknod /dev/optcd0 b 17 0
-To specify the base address if the driver is "compiled-in" to your kernel,
-you can use the kernel command line item (LILO option)
-             optcd=0x340
-with the right address.
-If you have compiled optcd as a module, you can load it with
- # insmod /usr/src/linux/modules/optcd.o
-or
- # insmod /usr/src/linux/modules/optcd.o optcd=0x340
-with the matching address value of your interface card.
-The driver employs a number of buffers to do read-ahead and block size
-conversion. The number of buffers is configurable in optcd.h, and has
-influence on the driver performance. For my machine (a P75), 6 buffers
-seems optimal, as can be seen from this table:
-#bufs   kb/s    %cpu
-1       97      0.1
-2       191     0.3
-3       188     0.2
-4       246     0.3
-5       189     19
-6       280     0.4
-7       281     7.0
-8       246     2.8
-16      281     3.4
-If you get a throughput significantly below 300 kb/s, try tweaking
-N_BUFS, and don't forget to mail me your results!
-I'd appreciate success/failure reports. If you find a bug, try
-recompiling the driver with some strategically chosen debug options
-(these can be found in optcd.h) and include the messages generated in
-your bug report. Good luck.
-Leo Spiekman (spiekman@dutette.et.tudelft.nl)
diff --git a/Documentation/cdrom/sbpcd b/Documentation/cdrom/sbpcd
deleted file mode 100644
index b3ba63f4ce3e..000000000000
--- a/Documentation/cdrom/sbpcd
+++ /dev/null
@@ -1,1061 +0,0 @@
-This README belongs to release 4.2 or newer of the SoundBlaster Pro
-(Matsushita, Kotobuki, Panasonic, CreativeLabs, Longshine and Teac)
-CD-ROM driver for Linux.
-sbpcd really, really is NOT for ANY IDE/ATAPI drive!
-Not even if you have an "original" SoundBlaster card with an IDE interface!
-So, you'd better have a look into README.ide if your port address is 0x1F0,
-0x170, 0x1E8, 0x168 or similar.
-I get tons of mails from IDE/ATAPI drive users - I really can't continue
-any more to answer them all. So, if your drive/interface information sheets
-mention "IDE" (primary, secondary, tertiary, quaternary) and the DOS driver
-invoking line within your CONFIG.SYS is using an address below 0x230:
-DON'T ROB MY LAST NERVE - jumper your interface to address 0x170 and IRQ 15
-(that is the "secondary IDE" configuration), set your drive to "master" and
-use ide-cd as your driver. If you do not have a second IDE hard disk, use the
-LILO commands
-   hdb=noprobe hdc=cdrom
-and get lucky.
-To make it fully clear to you: if you mail me about IDE/ATAPI drive problems,
-my answer is above, and I simply will discard your mail, hoping to stop the
-flood and to find time to lead my 12-year old son towards happy computing.
-The driver is able to drive the whole family of "traditional" AT-style (that
-is NOT the new "Enhanced IDE" or "ATAPI" drive standard) Matsushita,
-Kotobuki, Panasonic drives, sometimes labelled as "CreativeLabs". The
-well-known drives are CR-521, CR-522, CR-523, CR-562, CR-563.
-CR-574 is an IDE/ATAPI drive.
-The Longshine LCS-7260 is a double-speed drive which uses the "old"
-Matsushita command set. It is supported - with help by Serge Robyns.
-Vertos ("Elitegroup Computer Systems", ECS) has a similar drive - support
-has started; get in contact if you have such a "Vertos 100" or "ECS-AT"
-drive.
-There exists an "IBM External ISA CD-ROM Drive" which in fact is a CR-563
-with a special controller board. This drive is supported (the interface is
-of the "LaserMate" type), and it is possibly the best buy today (cheaper than
-an internal drive, and you can use it as an internal, too - e.g. plug it into
-a soundcard).
-CreativeLabs has a new drive "CD200" and a similar drive "CD200F". The latter
-is made by Funai and sometimes named "E2550UA", newer models may be named
-"MK4015". The CD200F drives should fully work.
-CD200 drives without "F" are still giving problems: drive detection and
-playing audio should work, data access will result in errors. I need qualified
-feedback about the bugs within the data functions or a drive (I never saw a
-CD200).
-The quad-speed Teac CD-55A drive is supported, but still does not reach "full
-speed". The data rate already reaches 500 kB/sec if you set SBP_BUFFER_FRAMES
-to 64 (it is not recommended to do that for normal "file access" usage, but it
-can speed up things a lot if you use something like "dd" to read from the
-drive; I use it for verifying self-written CDs this way).
-The drive itself is able to deliver 600 kB/sec, so this needs
-work; with the normal setup, the performance currently is not even as good as
-double-speed.
-This driver is NOT for Mitsumi or Sony or Aztech or Philips or XXX drives,
-and again: this driver is in no way usable for any IDE/ATAPI drive. If you 
-think your drive should work and it doesn't: send me the DOS driver for your
-beast (gzipped + uuencoded) and your CONFIG.SYS if you want to ask me for help,
-and include an original log message excerpt, and try to give all information
-a complete idiot needs to understand your hassle already with your first
-mail. And if you want to say "as I have mailed you before", be sure that I
-don't remember your "case" by such remarks; at the moment, I have some 
-hundreds of open correspondences about Linux CDROM questions (hope to reduce if
-the IDE/ATAPI user questions disappear). 
-This driver will work with the soundcard interfaces (SB Pro, SB 16, Galaxy,
-SoundFX, Mozart, MAD16 ...) and with the "no-sound" cards (Panasonic CI-101P,
-LaserMate, WDH-7001C, Longshine LCS-6853, Teac ...).
-It works with the "configurable" interface "Sequoia S-1000", too, which is 
-used on the Spea Media FX and Ensonic Soundscape sound cards. You have to
-specify the type "SBPRO 2" and the true CDROM port address with it, not the
-"configuration port" address.
-If you have a sound card which needs a "configuration driver" instead of
-jumpers for interface types and addresses (like Mozart cards) - those
-drivers get invoked before the DOS CDROM driver in your CONFIG.SYS, typical
-names are "cdsetup.sys" and "mztinit.sys" - let the sound driver do the
-CDROM port configuration (the leading comments in linux/drivers/sound/mad16.c
-are just for you!). Hannu Savolainen's mad16.c code is able to set up my
-Mozart card - I simply had to add
-   #define MAD16_CONF 0x06
-   #define MAD16_CDSEL 0x03
-to configure the CDROM interface for type "Panasonic" (LaserMate) and address
-0x340.
-The interface type has to get configured in linux/drivers/cdrom/sbpcd.h, 
-because the register layout is different between the "SoundBlaster" and the
-"LaserMate" type.
-I got a report that the Teac interface card "I/F E117098" is of type
-"SoundBlaster" (i.e. you have to set SBPRO to 1) even with the addresses
-0x300 and above. This is unusual, and it can't get covered by the auto
-probing scheme.
-The Teac 16-bit interface cards (like P/N E950228-00A, default address 0x2C0)
-need the SBPRO 3 setup.
-If auto-probing found the drive, the address is correct. The reported type
-may be wrong. A "mount" will give success only if the interface type is set
-right. Playing audio should work with a wrong set interface type, too.
-With some Teac and some CD200 drives I have seen interface cards which seem
-to lack the "drive select" lines; always drive 0 gets addressed. To avoid
-"mirror drives" (four drives detected where you only have one) with such
-interface cards, set MAX_DRIVES to 1 and jumper your drive to ID 0 (if
-possible).
-Up to 4 drives per interface card, and up to 4 interface cards are supported.
-All supported drive families can be mixed, but the CR-521 drives are 
-hard-wired to drive ID 0. The drives have to use different drive IDs, and each
-drive has to get a unique minor number (0...3), corresponding indirectly to 
-its drive ID.
-The drive IDs may be selected freely from 0 to 3 - they do not have to be in
-consecutive order.
-As Don Carroll, don@ds9.us.dell.com or FIDO 1:382/14, told me, it is possible
-to change old drives to any ID, too. He writes in this sense:
-   "In order to be able to use more than one single speed drive
-   (they do not have the ID jumpers) you must add a DIP switch
-   and two resistors. The pads are already on the board next to
-   the power connector. You will see the silkscreen for the
-   switch if you remove the top cover.
-                    1 2 3 4
-             ID 0 = x F F x             O = "on"
-             ID 1 = x O F x             F = "off"
-             ID 2 = x F O x             x = "don't care"
-             ID 3 = x O O x
-   Next to the switch are the positions for R76 (7k) and R78
-   (12k). I had to play around with the resistor values - ID 3
-   did not work with other values. If the values are not good,
-   ID 3 behaves like ID 0."
-To use more than 4 drives, you simply need a second controller card at a 
-different address and a second cable.
-The driver supports reading of data from the CD and playing of audio tracks.
-The audio part should run with WorkMan, xcdplayer, with the "non-X11" products
-CDplayer and WorkBone - tell me if it is not compatible with other software.
-The only accepted measure for correctness with the audio functions is the
-"cdtester" utility (appended) - most audio player programmers seem to be
-better musicians than programmers. ;-)
-With the CR-56x and the CD200 drives, the reading of audio frames is possible.
-This is implemented by an IOCTL function which reads READ_AUDIO frames of
-2352 bytes at once (configurable with the "READ_AUDIO" define, default is 0).
-Reading the same frame a second time gives different data; the frame data 
-start at a different position, but all read bytes are valid, and we always
-read 98 consecutive chunks (of 24 Bytes) as a frame. Reading more than 1 frame
-at once possibly misses some chunks at each frame boundary. This lack has to
-get corrected by external, "higher level" software which reads the same frame 
-again and tries to find and eliminate overlapping chunks (24-byte-pieces).
-The transfer rate with reading audio (1-frame-pieces) currently is very slow.
-This can be better reading bigger chunks, but the "missing" chunks possibly
-occur at the beginning of each single frame.
-The software interface possibly may change a bit the day the SCSI driver
-supports it too.
-With all but the CR-52x drives, MultiSession is supported.
-Photo CDs work (the "old" drives like CR-521 can access only the first
-session of a photoCD).
-At ftp.gwdg.de:/pub/linux/hpcdtoppm/ you will find Hadmut Danisch's package to
-convert photo CD image files and Gerd Knorr's viewing utility.
-The transfer rate will reach 150 kB/sec with CR-52x drives, 300 kB/sec with
-CR-56x drives, and currently not more than 500 kB/sec (usually less than
-250 kB/sec) with the Teac quad speed drives.
-XA (PhotoCD) disks with "old" drives give only 50 kB/sec.
-This release consists of
- this README file
- the driver file linux/drivers/cdrom/sbpcd.c
- the stub files linux/drivers/cdrom/sbpcd[234].c
- the header file linux/drivers/cdrom/sbpcd.h.
-To install:
-----------
-1. Setup your hardware parameters. Though the driver does "auto-probing" at a
-   lot of (not all possible!) addresses, this step is recommended for
-   everyday use. You should let sbpcd auto-probe once and use the reported
-   address if a drive got found. The reported type may be incorrect; it is
-   correct if you can mount a data CD. There is no choice for you with the
-   type; only one is right, the others are deadly wrong.
-   a. Go into /usr/src/linux/drivers/cdrom/sbpcd.h and configure it for your
-      hardware (near the beginning):
-      a1. Set it up for the appropriate type of interface board.
-          "Original" CreativeLabs sound cards need "SBPRO 1".
-          Most "compatible" sound cards (almost all "non-CreativeLabs" cards)
-          need "SBPRO 0".
-          The "no-sound" board from OmniCd needs the "SBPRO 1" setup.
-          The Teac 8-bit "no-sound" boards need the "SBPRO 1" setup.
-          The Teac 16-bit "no-sound" boards need the "SBPRO 3" setup.
-          All other "no-sound" boards need the "SBPRO 0" setup.
-          The Spea Media FX and Ensoniq SoundScape cards need "SBPRO 2".
-          sbpcd.c holds some examples in its auto-probe list.
-          If you configure "SBPRO" wrong, the playing of audio CDs will work,
-          but you will not be able to mount a data CD.
-      a2. Tell the address of your CDROM_PORT (not of the sound port).
-      a3. If 4 drives get found, but you have only one, set MAX_DRIVES to 1.
-      a4. Set DISTRIBUTION to 0.
-   b. Additionally for 2.a1 and 2.a2, the setup may be done during
-      boot time (via the "kernel command line" or "LILO option"):
-          sbpcd=0x320,LaserMate
-      or
-          sbpcd=0x230,SoundBlaster
-      or
-          sbpcd=0x338,SoundScape
-      or
-          sbpcd=0x2C0,Teac16bit
-      This is especially useful if you install a fresh distribution.
-      If the second parameter is a number, it gets taken as the type
-      setting; 0 is "LaserMate", 1 is "SoundBlaster", 2 is "SoundScape",
-      3 is "Teac16bit".
-      So, for example
-          sbpcd=0x230,1
-      is equivalent to
-          sbpcd=0x230,SoundBlaster
-2. "cd /usr/src/linux" and do a "make config" and select "y" for Matsushita
-   CD-ROM support and for ISO9660 FileSystem support. If you do not have a
-   second, third, or fourth controller installed, do not say "y" to the 
-   secondary Matsushita CD-ROM questions.
-3. Then make the kernel image ("make zlilo" or similar).
-4. Make the device file(s). This step usually already has been done by the
-   MAKEDEV script.
-   The driver uses MAJOR 25, so, if necessary, do
-        mknod /dev/sbpcd  b 25 0       (if you have only one drive)
-   and/or
-        mknod /dev/sbpcd0 b 25 0
-        mknod /dev/sbpcd1 b 25 1
-        mknod /dev/sbpcd2 b 25 2
-        mknod /dev/sbpcd3 b 25 3
-   to make the node(s).
-   The "first found" drive gets MINOR 0 (regardless of its jumpered ID), the
-   "next found" (at the same cable) gets MINOR 1, ...
-   
-   For a second interface board, you have to make nodes like
-        mknod /dev/sbpcd4 b 26 0
-        mknod /dev/sbpcd5 b 26 1
-   and so on. Use the MAJORs 26, 27, 28.
-   If you further make a link like
-        ln -s sbpcd /dev/cdrom
-   you can use the name /dev/cdrom, too.
-5. Reboot with the new kernel.
-You should now be able to do
-              mkdir /CD
-and 
-              mount -rt iso9660 /dev/sbpcd /CD
-or
-              mount -rt iso9660 -o block=2048 /dev/sbpcd /CD
-and see the contents of your CD in the /CD directory.
-To use audio CDs, a mounting is not recommended (and it would fail if the
-first track is not a data track).
-Using sbpcd as a "loadable module":
-----------------------------------
-If you do NOT select "Matsushita/Panasonic CDROM driver support" during the
-"make config" of your kernel, you can build the "loadable module" sbpcd.o.
-If sbpcd gets used as a module, the support of more than one interface
-card (i.e. drives 4...15) is disabled.
-You can specify interface address and type with the "insmod" command like:
- # insmod /usr/src/linux/modules/sbpcd.o sbpcd=0x340,0
-or
- # insmod /usr/src/linux/modules/sbpcd.o sbpcd=0x230,1
-or
- # insmod /usr/src/linux/modules/sbpcd.o sbpcd=0x338,2
-where the last number represents the SBPRO setting (no strings allowed here).
-Things of interest:
-------------------
-The driver is configured to try the LaserMate type of interface at I/O port
-0x0340 first. If this is not appropriate, sbpcd.h should get changed
-(you will find the right place - just at the beginning).
-No DMA and no IRQ is used.
-To reduce or increase the amount of kernel messages, edit sbpcd.c and play
-with the "DBG_xxx" switches (initialization of the variable "sbpcd_debug").
-Don't forget to reflect on what you do; enabling all DBG_xxx switches at once
-may crash your system, and each message line is accompanied by a delay.
-The driver uses the "variable BLOCK_SIZE" feature. To use it, you have to
-specify "block=2048" as a mount option. Doing this will disable the direct
-execution of a binary from the CD; you have to copy it to a device with the
-standard BLOCK_SIZE (1024) first. So, do not use this if your system is
-directly "running from the CDROM" (like some of Yggdrasil's installation
-variants). There are CDs on the market (like the German "unifix" Linux
-distribution) which MUST get handled with a block_size of 1024. Generally,
-one can say all the CDs which hold files of the name YMTRANS.TBL are defective;
-do not use block=2048 with those.
-Within sbpcd.h, you will find some "#define"s (e.g. EJECT and JUKEBOX). With
-these, you can configure the driver for some special things.
-You can use the appended program "cdtester" to set the auto-eject feature
-during runtime. Jeff Tranter's "eject" utility can do this, too (and more)
-for you.
-There is an ioctl CDROMMULTISESSION to obtain with a user program if
-the CD is an XA disk and - if it is - where the last session starts. The
-"cdtester" program illustrates how to call it.
-Auto-probing at boot time:
--------------------------
-The driver does auto-probing at many well-known interface card addresses,
-but not all:
-Some probings can cause a hang if an NE2000 ethernet card gets touched, because
-SBPCD's auto-probing happens before the initialization of the net drivers.
-Those "hazardous" addresses are excluded from auto-probing; the "kernel 
-command line" feature has to be used during installation if you have your 
-drive at those addresses. The "module" version is allowed to probe at those
-addresses, too.
-The auto-probing looks first at the configured address resp. the address
-submitted by the kernel command line. With this, it is possible to use this
-driver within installation boot floppies, and for any non-standard address,
-too.
-Auto-probing will make an assumption about the interface type ("SBPRO" or not),
-based upon the address. That assumption may be wrong (initialization will be
-o.k., but you will get I/O errors during mount). In that case, use the "kernel
-command line" feature and specify address & type at boot time to find out the
-right setup.
-For everyday use, address and type should get configured within sbpcd.h. That
-will stop the auto-probing due to success with the first try.
-The kernel command "sbpcd=0" suppresses each auto-probing and causes
-the driver not to find any drive; it is meant for people who love sbpcd
-so much that they do not want to miss it, even if they miss the drives. ;-)  
-If you configure "#define CDROM_PORT 0" in sbpcd.h, the auto-probing is
-initially disabled and needs an explicit kernel command to get activated.
-Once activated, it does not stop before success or end-of-list. This may be
-useful within "universal" CDROM installation boot floppies (but using the 
-loadable module would be better because it allows an "extended" auto-probing
-without fearing NE2000 cards).
-To shorten the auto-probing list to a single entry, set DISTRIBUTION 0 within
-sbpcd.h.
-Setting up address and interface type:
--------------------------------------
-If your I/O port address is not 0x340, you have to look for the #defines near
-the beginning of sbpcd.h and configure them: set SBPRO to 0 or 1 or 2, and
-change CDROM_PORT to the address of your CDROM I/O port.
-Almost all of the "SoundBlaster compatible" cards behave like the no-sound
-interfaces, i.e. need SBPRO 0! 
-With "original" SB Pro cards, an initial setting of CD_volume through the
-sound card's MIXER register gets done.
-If you are using a "compatible" sound card of types "LaserMate" or "SPEA",
-you can set SOUND_BASE (in sbpcd.h) to get it done with your card, too...
-Using audio CDs:
----------------
-Workman, WorkBone, xcdplayer, cdplayer and the nice little tool "cdplay" (see
-README.aztcd from the Aztech driver package) should work.
-The program CDplayer likes to talk to "/dev/mcd" only, xcdplayer wants
-"/dev/rsr0", workman loves "/dev/sr0" or "/dev/cdrom" - so, make the 
-appropriate links to use them without the need to supply parameters.
-Copying audio tracks:
---------------------
-The following program will copy track 1 (or a piece of it) from an audio CD
-into the file "track01":
-/*=================== begin program ========================================*/
-/*
- * read an audio track from a CD
- *
- * (c) 1994 Eberhard Moenkeberg <emoenke@gwdg.de>
- *          may be used & enhanced freely
- *
- * Due to non-existent sync bytes at the beginning of each audio frame (or due
- * to a firmware bug within all known drives?), it is currently a kind of
- * fortune if two consecutive frames fit together.
- * Usually, they overlap, or a little piece is missing. This happens in units
- * of 24-byte chunks. It has to get fixed by higher-level software (reading
- * until an overlap occurs, and then eliminate the overlapping chunks). 
- * ftp.gwdg.de:/pub/linux/misc/cdda2wav-sbpcd.*.tar.gz holds an example of
- * such an algorithm.
- * This example program further is missing to obtain the SubChannel data
- * which belong to each frame.
- *
- * This is only an example of the low-level access routine. The read data are
- * pure 16-bit CDDA values; they have to get converted to make sound out of
- * them.
- * It is no fun to listen to it without prior overlap/underlap correction!
- */
-#include <stdio.h>
-#include <sys/ioctl.h>
-#include <sys/types.h>
-#include <linux/cdrom.h>
-static struct cdrom_tochdr hdr;
-static struct cdrom_tocentry entry[101];
-static struct cdrom_read_audio arg;
-static u_char buffer[CD_FRAMESIZE_RAW];
-static int datafile, drive;
-static int i, j, limit, track, err;
-static char filename[32];
-int main(int argc, char *argv[])
-{
-/*
- * open /dev/cdrom
- */
-  drive=open("/dev/cdrom", 0);
-  if (drive<0)
-    {
-      fprintf(stderr, "can't open drive.\n");
-      exit (-1);
-    }
-/*
- * get TocHeader
- */
-  fprintf(stdout, "getting TocHeader...\n");
-  err=ioctl(drive, CDROMREADTOCHDR, &hdr);
-  if (err!=0)
-    {
-      fprintf(stderr, "can't get TocHeader (error %d).\n", err);
-      exit (-1);
-    }
-  else
-    fprintf(stdout, "TocHeader: %d %d\n", hdr.cdth_trk0, hdr.cdth_trk1);
-/*
- * get and display all TocEntries
- */
-  fprintf(stdout, "getting TocEntries...\n");
-  for (i=1;i<=hdr.cdth_trk1+1;i++)
-    {
-      if (i!=hdr.cdth_trk1+1) entry[i].cdte_track = i;
-      else entry[i].cdte_track = CDROM_LEADOUT;
-      entry[i].cdte_format = CDROM_LBA;
-      err=ioctl(drive, CDROMREADTOCENTRY, &entry[i]);
-      if (err!=0)
-        {
-          fprintf(stderr, "can't get TocEntry #%d (error %d).\n", i, err);
-          exit (-1);
-        }
-      else
-        {
-          fprintf(stdout, "TocEntry #%d: %1X %1X %06X %02X\n",
-                 entry[i].cdte_track,
-                 entry[i].cdte_adr,
-                 entry[i].cdte_ctrl,
-                 entry[i].cdte_addr.lba,
-                 entry[i].cdte_datamode);
-        }
-    }
-  fprintf(stdout, "got all TocEntries.\n");
-/*
- * ask for track number (not implemented here)
- */
-track=1;
-#if 0 /* just read a little piece (4 seconds) */
-entry[track+1].cdte_addr.lba=entry[track].cdte_addr.lba+300;
-#endif
-/*
- * read track into file
- */
-  sprintf(filename, "track%02d\0", track);
-  datafile=creat(filename, 0755);
-  if (datafile<0)
-    {
-      fprintf(stderr, "can't open datafile %s.\n", filename);
-      exit (-1);
-    }
-  arg.addr.lba=entry[track].cdte_addr.lba;
-  arg.addr_format=CDROM_LBA; /* CDROM_MSF would be possible here, too. */
-  arg.nframes=1;
-  arg.buf=&buffer[0];
-  limit=entry[track+1].cdte_addr.lba;
-  for (;arg.addr.lba<limit;arg.addr.lba++)
-    {
-      err=ioctl(drive, CDROMREADAUDIO, &arg);
-      if (err!=0)
-        {
-          fprintf(stderr, "can't read abs. frame #%d (error %d).\n", 
-                 arg.addr.lba, err);
-        }
-      j=write(datafile, &buffer[0], CD_FRAMESIZE_RAW);
-      if (j!=CD_FRAMESIZE_RAW)
-        {
-          fprintf(stderr,"I/O error (datafile) at rel. frame %d\n",
-                         arg.addr.lba-entry[track].cdte_addr.lba);
-        }
-      arg.addr.lba++;
-    }
-    return 0;
-}
-/*===================== end program ========================================*/
-At ftp.gwdg.de:/pub/linux/misc/cdda2wav-sbpcd.*.tar.gz is an adapted version of
-Heiko Eissfeldt's digital-audio to .WAV converter (the original is there, too).
-This is preliminary, as Heiko himself will care about it.
-Known problems:
---------------
-Currently, the detection of disk change or removal is actively disabled.
-Most attempts to read the UPC/EAN code result in a stream of zeroes. All my
-drives are mostly telling there is no UPC/EAN code on disk or there is, but it
-is an all-zero number. I guess now almost no CD holds such a number.
-Bug reports, comments, wishes, donations (technical information is a donation,
-too :-) etc. to emoenke@gwdg.de.
-SnailMail address, preferable for CD editors if they want to submit a free
-"cooperation" copy:
-                         Eberhard Moenkeberg
-                         Reinholdstr. 14
-                         D-37083 Goettingen
-                         Germany
---
-Appendix -- the "cdtester" utility:
-/*
- * cdtester.c -- test the audio functions of a CD driver
- *
- * (c) 1995 Eberhard Moenkeberg <emoenke@gwdg.de>
- *          published under the GPL
- *
- *          made under heavy use of the "Tiny Audio CD Player"
- *          from Werner Zimmermann <zimmerma@rz.fht-esslingen.de>
- *          (see linux/drivers/block/README.aztcd)
- */
-#undef AZT_PRIVATE_IOCTLS /* not supported by every CDROM driver */
-#define SBP_PRIVATE_IOCTLS /* not supported by every CDROM driver */
-#include <stdio.h>
-#include <stdio.h>
-#include <malloc.h>
-#include <sys/ioctl.h>
-#include <sys/types.h>
-#include <linux/cdrom.h>
-#ifdef AZT_PRIVATE_IOCTLS
-#include <linux/../../drivers/cdrom/aztcd.h>
-#endif /* AZT_PRIVATE_IOCTLS */
-#ifdef SBP_PRIVATE_IOCTLS
-#include <linux/../../drivers/cdrom/sbpcd.h>
-#include <linux/fs.h>
-#endif /* SBP_PRIVATE_IOCTLS */
-struct cdrom_tochdr hdr;
-struct cdrom_tochdr tocHdr;
-struct cdrom_tocentry TocEntry[101];
-struct cdrom_tocentry entry;
-struct cdrom_multisession ms_info;
-struct cdrom_read_audio read_audio;
-struct cdrom_ti ti;
-struct cdrom_subchnl subchnl;
-struct cdrom_msf msf;
-struct cdrom_volctrl volctrl;
-#ifdef AZT_PRIVATE_IOCTLS
-union
-{
-        struct cdrom_msf msf;
-        unsigned char buf[CD_FRAMESIZE_RAW];
-} azt;
-#endif /* AZT_PRIVATE_IOCTLS */
-int i, i1, i2, i3, j, k;
-unsigned char sequence=0;
-unsigned char command[80];
-unsigned char first=1, last=1;
-char *default_device="/dev/cdrom";
-char dev[20];
-char filename[20];
-int drive;
-int datafile;
-int rc;
-void help(void)
-{
-        printf("Available Commands:\n");
-        printf("STOP          s      EJECT        e       QUIT         q\n");
-        printf("PLAY TRACK    t      PAUSE        p       RESUME       r\n");
-        printf("NEXT TRACK    n      REPEAT LAST  l       HELP         h\n");
-        printf("SUBCHANNEL_Q  c      TRACK INFO   i       PLAY AT      a\n");
-        printf("READ          d      READ RAW     w       READ AUDIO   A\n");
-        printf("MS-INFO       M      TOC          T       START        S\n");
-        printf("SET EJECTSW   X      DEVICE       D       DEBUG        Y\n");
-        printf("AUDIO_BUFSIZ  Z      RESET        R       SET VOLUME   v\n");
-        printf("GET VOLUME    V\n");
-}
-/*
- *  convert MSF number (3 bytes only) to Logical_Block_Address 
- */
-int msf2lba(u_char *msf)
-{
-        int i;
-        
-        i=(msf[0] * CD_SECS + msf[1]) * CD_FRAMES + msf[2] - CD_BLOCK_OFFSET;
-        if (i<0) return (0);
-        return (i);
-}
-/*
- *  convert logical_block_address to m-s-f_number (3 bytes only)
- */
-void lba2msf(int lba, unsigned char *msf)
-{
-        lba += CD_BLOCK_OFFSET;
-        msf[0] = lba / (CD_SECS*CD_FRAMES);
-        lba %= CD_SECS*CD_FRAMES;
-        msf[1] = lba / CD_FRAMES;
-        msf[2] = lba % CD_FRAMES;
-}
-int init_drive(char *dev)
-{
-        unsigned char msf_ent[3];
-        /*
-         * open the device
-         */
-        drive=open(dev,0);
-        if (drive<0) return (-1);
-        /*
-         * get TocHeader
-         */
-        printf("getting TocHeader...\n");
-        rc=ioctl(drive,CDROMREADTOCHDR,&hdr);
-        if (rc!=0)
-        {
-                printf("can't get TocHeader (error %d).\n",rc);
-                return (-2);
-        }
-        else
-                first=hdr.cdth_trk0;
-                last=hdr.cdth_trk1;
-                printf("TocHeader: %d %d\n",hdr.cdth_trk0,hdr.cdth_trk1);
-        /*
-         * get and display all TocEntries
-         */
-        printf("getting TocEntries...\n");
-        for (i=1;i<=hdr.cdth_trk1+1;i++)
-        {
-                if (i!=hdr.cdth_trk1+1) TocEntry[i].cdte_track = i;
-                else TocEntry[i].cdte_track = CDROM_LEADOUT;
-                TocEntry[i].cdte_format = CDROM_LBA;
-                rc=ioctl(drive,CDROMREADTOCENTRY,&TocEntry[i]);
-                if (rc!=0)
-                {
-                        printf("can't get TocEntry #%d (error %d).\n",i,rc);
-                }
-                else
-                {
-                        lba2msf(TocEntry[i].cdte_addr.lba,&msf_ent[0]);
-                        if (TocEntry[i].cdte_track==CDROM_LEADOUT)
-                        {
-                                printf("TocEntry #%02X: %1X %1X %02d:%02d:%02d (lba: 0x%06X) %02X\n",
-                                       TocEntry[i].cdte_track,
-                                       TocEntry[i].cdte_adr,
-                                       TocEntry[i].cdte_ctrl,
-                                       msf_ent[0],
-                                       msf_ent[1],
-                                       msf_ent[2],
-                                       TocEntry[i].cdte_addr.lba,
-                                       TocEntry[i].cdte_datamode);
-                        }
-                        else
-                        {
-                                printf("TocEntry #%02d: %1X %1X %02d:%02d:%02d (lba: 0x%06X) %02X\n",
-                                       TocEntry[i].cdte_track,
-                                       TocEntry[i].cdte_adr,
-                                       TocEntry[i].cdte_ctrl,
-                                       msf_ent[0],
-                                       msf_ent[1],
-                                       msf_ent[2],
-                                       TocEntry[i].cdte_addr.lba,
-                                       TocEntry[i].cdte_datamode);
-                        }
-                }
-        }
-        return (hdr.cdth_trk1); /* number of tracks */
-}
-void display(int size,unsigned char *buffer)
-{
-        k=0;
-        getchar();
-        for (i=0;i<(size+1)/16;i++)
-        {
-                printf("%4d:",i*16);
-                for (j=0;j<16;j++)
-                {
-                        printf(" %02X",buffer[i*16+j]);
-                }
-                printf("  ");
-                for (j=0;j<16;j++)
-                {
-                        if (isalnum(buffer[i*16+j])) 
-                                printf("%c",buffer[i*16+j]);
-                        else
-                                printf(".");
-                }
-                printf("\n"); 
-                k++;
-                if (k>=20)
-                {
-                        printf("press ENTER to continue\n");
-                        getchar();
-                        k=0;
-                }
-        } 
-} 
-int main(int argc, char *argv[])
-{
-        printf("\nTesting tool for a CDROM driver's audio functions V0.1\n");
-        printf("(C) 1995 Eberhard Moenkeberg <emoenke@gwdg.de>\n");
-        printf("initializing...\n");
-        
-        rc=init_drive(default_device);
-        if (rc<0) printf("could not open %s (rc=%d).\n",default_device,rc);
-        help();
-        while (1)
-        {
-                printf("Give a one-letter command (h = help): ");
-                scanf("%s",command);
-                command[1]=0;
-                switch (command[0])
-                {
-                case 'D':
-                        printf("device name (f.e. /dev/sbpcd3): ? ");
-                        scanf("%s",&dev);
-                        close(drive);
-                        rc=init_drive(dev);
-                        if (rc<0) printf("could not open %s (rc %d).\n",dev,rc);
-                        break;
-                case 'e':
-                        rc=ioctl(drive,CDROMEJECT);
-                        if (rc<0) printf("CDROMEJECT: rc=%d.\n",rc);
-                        break;
-                case 'p':
-                        rc=ioctl(drive,CDROMPAUSE);
-                        if (rc<0) printf("CDROMPAUSE: rc=%d.\n",rc);
-                        break;
-                case 'r':
-                        rc=ioctl(drive,CDROMRESUME);
-                        if (rc<0) printf("CDROMRESUME: rc=%d.\n",rc);
-                        break;
-                case 's':
-                        rc=ioctl(drive,CDROMSTOP);
-                        if (rc<0) printf("CDROMSTOP: rc=%d.\n",rc);
-                        break;
-                case 'S':
-                        rc=ioctl(drive,CDROMSTART);
-                        if (rc<0) printf("CDROMSTART: rc=%d.\n",rc);
-                        break;
-                case 't':
-                        rc=ioctl(drive,CDROMREADTOCHDR,&tocHdr);
-                        if (rc<0)
-                        {
-                                printf("CDROMREADTOCHDR: rc=%d.\n",rc);
-                                break;
-                        }
-                        first=tocHdr.cdth_trk0;
-                        last= tocHdr.cdth_trk1;
-                        if ((first==0)||(first>last))
-                        {
-                                printf ("--got invalid TOC data.\n");
-                        }
-                        else
-                        {
-                                printf("--enter track number(first=%d, last=%d): ",first,last);
-                                scanf("%d",&i1);
-                                ti.cdti_trk0=i1;
-                                if (ti.cdti_trk0<first) ti.cdti_trk0=first;
-                                if (ti.cdti_trk0>last) ti.cdti_trk0=last;
-                                ti.cdti_ind0=0;
-                                ti.cdti_trk1=last;
-                                ti.cdti_ind1=0;
-                                rc=ioctl(drive,CDROMSTOP);
-                                rc=ioctl(drive,CDROMPLAYTRKIND,&ti);
-                                if (rc<0) printf("CDROMPLAYTRKIND: rc=%d.\n",rc);
-                        }
-                        break;
-                case 'n':
-                        rc=ioctl(drive,CDROMSTOP);
-                        if (++ti.cdti_trk0>last) ti.cdti_trk0=last;
-                        ti.cdti_ind0=0;
-                        ti.cdti_trk1=last;
-                        ti.cdti_ind1=0;
-                        rc=ioctl(drive,CDROMPLAYTRKIND,&ti);
-                        if (rc<0) printf("CDROMPLAYTRKIND: rc=%d.\n",rc);
-                        break;
-                case 'l':
-                        rc=ioctl(drive,CDROMSTOP);
-                        if (--ti.cdti_trk0<first) ti.cdti_trk0=first;
-                        ti.cdti_ind0=0;
-                        ti.cdti_trk1=last;
-                        ti.cdti_ind1=0;
-                        rc=ioctl(drive,CDROMPLAYTRKIND,&ti);
-                        if (rc<0) printf("CDROMPLAYTRKIND: rc=%d.\n",rc);
-                        break;
-                case 'c':
-                        subchnl.cdsc_format=CDROM_MSF;
-                        rc=ioctl(drive,CDROMSUBCHNL,&subchnl);
-                        if (rc<0) printf("CDROMSUBCHNL: rc=%d.\n",rc);
-                        else
-                        {
-                                printf("AudioStatus:%s  Track:%d  Mode:%d  MSF=%02d:%02d:%02d\n",
-                                       subchnl.cdsc_audiostatus==CDROM_AUDIO_PLAY ? "PLAYING":"NOT PLAYING",
-                                       subchnl.cdsc_trk,subchnl.cdsc_adr, 
-                                       subchnl.cdsc_absaddr.msf.minute,
-                                       subchnl.cdsc_absaddr.msf.second,
-                                       subchnl.cdsc_absaddr.msf.frame);
-                        }
-                        break;              
-                case 'i':
-                        printf("Track No.: ");
-                        scanf("%d",&i1);
-                        entry.cdte_track=i1;
-                        if (entry.cdte_track<first) entry.cdte_track=first;
-                        if (entry.cdte_track>last)  entry.cdte_track=last;
-                        entry.cdte_format=CDROM_MSF;
-                        rc=ioctl(drive,CDROMREADTOCENTRY,&entry);
-                        if (rc<0) printf("CDROMREADTOCENTRY: rc=%d.\n",rc);
-                        else
-                        {
-                                printf("Mode %d Track, starts at %02d:%02d:%02d\n",
-                                       entry.cdte_adr,
-                                       entry.cdte_addr.msf.minute,
-                                       entry.cdte_addr.msf.second,
-                                       entry.cdte_addr.msf.frame);
-                        }
-                        break;
-                case 'a':
-                        printf("Address (min:sec:frm)  ");
-                        scanf("%d:%d:%d",&i1,&i2,&i3);
-                        msf.cdmsf_min0=i1;
-                        msf.cdmsf_sec0=i2;
-                        msf.cdmsf_frame0=i3;
-                        if (msf.cdmsf_sec0>59) msf.cdmsf_sec0=59;
-                        if (msf.cdmsf_frame0>74) msf.cdmsf_frame0=74;
-                        lba2msf(TocEntry[last+1].cdte_addr.lba-1,&msf.cdmsf_min1);
-                        rc=ioctl(drive,CDROMSTOP);
-                        rc=ioctl(drive,CDROMPLAYMSF,&msf);
-                        if (rc<0) printf("CDROMPLAYMSF: rc=%d.\n",rc);
-                        break;
-                case 'V':
-                        rc=ioctl(drive,CDROMVOLREAD,&volctrl);
-                        if (rc<0) printf("CDROMVOLCTRL: rc=%d.\n",rc);
-                        printf("Volume: channel 0 (left) %d, channel 1 (right) %d\n",volctrl.channel0,volctrl.channel1);
-                        break;  
-                case 'R':
-                        rc=ioctl(drive,CDROMRESET);
-                        if (rc<0) printf("CDROMRESET: rc=%d.\n",rc);
-                        break;
-#ifdef AZT_PRIVATE_IOCTLS /*not supported by every CDROM driver*/
-                case 'd':
-                        printf("Address (min:sec:frm)  ");
-                        scanf("%d:%d:%d",&i1,&i2,&i3);
-                        azt.msf.cdmsf_min0=i1;
-                        azt.msf.cdmsf_sec0=i2;
-                        azt.msf.cdmsf_frame0=i3;
-                        if (azt.msf.cdmsf_sec0>59) azt.msf.cdmsf_sec0=59;
-                        if (azt.msf.cdmsf_frame0>74) azt.msf.cdmsf_frame0=74;
-                        rc=ioctl(drive,CDROMREADMODE1,&azt.msf);
-                        if (rc<0) printf("CDROMREADMODE1: rc=%d.\n",rc);
-                        else display(CD_FRAMESIZE,azt.buf);
-                        break;
-                case 'w':
-                        printf("Address (min:sec:frame)  ");
-                        scanf("%d:%d:%d",&i1,&i2,&i3);
-                        azt.msf.cdmsf_min0=i1;
-                        azt.msf.cdmsf_sec0=i2;
-                        azt.msf.cdmsf_frame0=i3;
-                        if (azt.msf.cdmsf_sec0>59) azt.msf.cdmsf_sec0=59;
-                        if (azt.msf.cdmsf_frame0>74) azt.msf.cdmsf_frame0=74;
-                        rc=ioctl(drive,CDROMREADMODE2,&azt.msf);
-                        if (rc<0) printf("CDROMREADMODE2: rc=%d.\n",rc);
-                        else display(CD_FRAMESIZE_RAW,azt.buf); /* currently only 2336 */
-                        break;  
-#endif
-                case 'v':
-                        printf("--Channel 0 (Left)  (0-255): ");
-                        scanf("%d",&i1);
-                        volctrl.channel0=i1;
-                        printf("--Channel 1 (Right) (0-255): ");
-                        scanf("%d",&i1);
-                        volctrl.channel1=i1;
-                        volctrl.channel2=0;
-                        volctrl.channel3=0;
-                        rc=ioctl(drive,CDROMVOLCTRL,&volctrl);
-                        if (rc<0) printf("CDROMVOLCTRL: rc=%d.\n",rc);
-                        break;  
-                case 'q':
-                        close(drive);
-                        exit(0);
-                case 'h':
-                        help();
-                        break;
-                case 'T': /* display TOC entry - without involving the driver */
-                        scanf("%d",&i);
-                        if ((i<hdr.cdth_trk0)||(i>hdr.cdth_trk1))
-                                printf("invalid track number.\n");
-                        else
-                                printf("TocEntry %02d: adr=%01X ctrl=%01X msf=%02d:%02d:%02d mode=%02X\n",
-                                       TocEntry[i].cdte_track,
-                                       TocEntry[i].cdte_adr,
-                                       TocEntry[i].cdte_ctrl,
-                                       TocEntry[i].cdte_addr.msf.minute,
-                                       TocEntry[i].cdte_addr.msf.second,
-                                       TocEntry[i].cdte_addr.msf.frame,
-                                       TocEntry[i].cdte_datamode);
-                        break;
-                case 'A': /* read audio data into file */
-                        printf("Address (min:sec:frm) ? ");
-                        scanf("%d:%d:%d",&i1,&i2,&i3);
-                        read_audio.addr.msf.minute=i1;
-                        read_audio.addr.msf.second=i2;
-                        read_audio.addr.msf.frame=i3;
-                        read_audio.addr_format=CDROM_MSF;
-                        printf("# of frames ? ");
-                        scanf("%d",&i1);
-                        read_audio.nframes=i1;
-                        k=read_audio.nframes*CD_FRAMESIZE_RAW;
-                        read_audio.buf=malloc(k);
-                        if (read_audio.buf==NULL)
-                        {
-                                printf("can't malloc %d bytes.\n",k);
-                                break;
-                        }
-                        sprintf(filename,"audio_%02d%02d%02d_%02d.%02d\0",
-                                read_audio.addr.msf.minute,
-                                read_audio.addr.msf.second,
-                                read_audio.addr.msf.frame,
-                                read_audio.nframes,
-                                ++sequence);
-                        datafile=creat(filename, 0755);
-                        if (datafile<0)
-                        {
-                                printf("can't open datafile %s.\n",filename);
-                                break;
-                        }
-                        rc=ioctl(drive,CDROMREADAUDIO,&read_audio);
-                        if (rc!=0)
-                        {
-                                printf("CDROMREADAUDIO: rc=%d.\n",rc);
-                        }
-                        else
-                        {
-                                rc=write(datafile,&read_audio.buf,k);
-                                if (rc!=k) printf("datafile I/O error (%d).\n",rc);
-                        }
-                        close(datafile);
-                        break;
-                case 'X': /* set EJECT_SW (0: disable, 1: enable auto-ejecting) */
-                        scanf("%d",&i);
-                        rc=ioctl(drive,CDROMEJECT_SW,i);
-                        if (rc!=0)
-                                printf("CDROMEJECT_SW: rc=%d.\n",rc);
-                        else
-                                printf("EJECT_SW set to %d\n",i);
-                        break;
-                case 'M': /* get the multisession redirection info */
-                        ms_info.addr_format=CDROM_LBA;
-                        rc=ioctl(drive,CDROMMULTISESSION,&ms_info);
-                        if (rc!=0)
-                        {
-                                printf("CDROMMULTISESSION(lba): rc=%d.\n",rc);
-                        }
-                        else
-                        {
-                                if (ms_info.xa_flag) printf("MultiSession offset (lba): %d (0x%06X)\n",ms_info.addr.lba,ms_info.addr.lba);
-                                else
-                                {
-                                        printf("this CD is not an XA disk.\n");
-                                        break;
-                                }
-                        }
-                        ms_info.addr_format=CDROM_MSF;
-                        rc=ioctl(drive,CDROMMULTISESSION,&ms_info);
-                        if (rc!=0)
-                        {
-                                printf("CDROMMULTISESSION(msf): rc=%d.\n",rc);
-                        }
-                        else
-                        {
-                                if (ms_info.xa_flag)
-                                        printf("MultiSession offset (msf): %02d:%02d:%02d (0x%02X%02X%02X)\n",
-                                               ms_info.addr.msf.minute,
-                                               ms_info.addr.msf.second,
-                                               ms_info.addr.msf.frame,
-                                               ms_info.addr.msf.minute,
-                                               ms_info.addr.msf.second,
-                                               ms_info.addr.msf.frame);
-                                else printf("this CD is not an XA disk.\n");
-                        }
-                        break;
-#ifdef SBP_PRIVATE_IOCTLS
-                case 'Y': /* set the driver's message level */
-#if 0 /* not implemented yet */
-                        printf("enter switch name (f.e. DBG_CMD): ");
-                        scanf("%s",&dbg_switch);
-                        j=get_dbg_num(dbg_switch);
-#else
-                        printf("enter DDIOCSDBG switch number: ");
-                        scanf("%d",&j);
-#endif
-                        printf("enter 0 for \"off\", 1 for \"on\": ");
-                        scanf("%d",&i);
-                        if (i==0) j|=0x80;
-                        printf("calling \"ioctl(drive,DDIOCSDBG,%d)\"\n",j);
-                        rc=ioctl(drive,DDIOCSDBG,j);
-                        printf("DDIOCSDBG: rc=%d.\n",rc);
-                        break;
-                case 'Z': /* set the audio buffer size */
-                        printf("# frames wanted: ? ");
-                        scanf("%d",&j);
-                        rc=ioctl(drive,CDROMAUDIOBUFSIZ,j);
-                        printf("%d frames granted.\n",rc);
-                        break;
-#endif /* SBP_PRIVATE_IOCTLS */
-                default:
-                        printf("unknown command: \"%s\".\n",command);
-                        break;
-                }
-        }
-        return 0;
-}
-/*==========================================================================*/
diff --git a/Documentation/cdrom/sjcd b/Documentation/cdrom/sjcd
deleted file mode 100644
index 74a14847b93a..000000000000
--- a/Documentation/cdrom/sjcd
+++ /dev/null
@@ -1,60 +0,0 @@
- -- Documentation/cdrom/sjcd
-                                80% of the work takes 20% of the time,
-                                20% of the work takes 80% of the time...
-                                                (Murphy's law)
-                                Once started, training can not be stopped...
-                                                (Star Wars)
-This is the README for the sjcd cdrom driver, version 1.6.
-This file is meant as a tips & tricks edge for the usage of the SANYO CDR-H94A
-cdrom drive. It will grow as the questions arise. ;-)
-For info on configuring the ISP16 sound card look at Documentation/cdrom/isp16.
-The driver should work with any of the Panasonic, Sony or Mitsumi style
-CDROM interfaces.
-The cdrom interface on Media Magic's soft configurable sound card ISP16,
-which used to be included in the driver, is now supported in a separate module.
-This initialisation module will probably also work with other interfaces
-based on an OPTi 82C928 or 82C929 chip (like MAD16 and Mozart): see the
-documentation Documentation/cdrom/isp16.
-The device major for sjcd is 18, and minor is 0. Create a block special
-file in your /dev directory (e.g., /dev/sjcd) with these numbers.
-(For those who don't know, being root and doing the following should do
-the trick:
-  mknod -m 644 /dev/sjcd b 18 0
-and mount the cdrom by /dev/sjcd).
-The default configuration parameters are:
-  base address 0x340
-  no irq
-  no dma
-(Actually the CDR-H94A doesn't know how to use irq and dma.)
-As of version 1.2, setting base address at boot time is supported
-through the use of command line options: type at the "boot:" prompt:
-  linux sjcd=<base_address>
-(where you would use the kernel labeled "linux" in lilo's configuration
-file /etc/lilo.conf). You could also use 'append="sjcd=<configuration_info>"'
-in the appropriate section of /etc/lilo.conf
-If you're building a kernel yourself you can set your default base
-i/o address with SJCD_BASE_ADDR in /usr/src/linux/drivers/cdrom/sjcd.h.
-The sjcd driver supports being loaded as a module. The following
-command will set the base i/o address on the fly (assuming you
-have installed the module in an appropriate place).
-  insmod sjcd.o sjcd_base=<base_address>
-Have fun!
-If something is wrong, please email to          vadim@rbrf.ru
-                                        or      vadim@ipsun.ras.ru
-                                        or      model@cecmow.enet.dec.com
-                                        or      H.T.M.v.d.Maarel@marin.nl
-It happens sometimes that Vadim is not reachable by mail. For these
-instances, Eric van der Maarel will help too.
-                Vadim V. Model, Eric van der Maarel, Eberhard Moenkeberg
diff --git a/Documentation/cdrom/sonycd535 b/Documentation/cdrom/sonycd535
deleted file mode 100644
index b81e109970aa..000000000000
--- a/Documentation/cdrom/sonycd535
+++ /dev/null
@@ -1,122 +0,0 @@
-              README FOR LINUX SONY CDU-535/531 DRIVER
-              ========================================
-This is the Sony CDU-535 (and 531) driver version 0.7 for Linux.
-I do not think I have the documentation to add features like DMA support
-so if anyone else wants to pursue it or help me with it, please do.
-(I need to see what was done for the CDU-31A driver -- perhaps I can
-steal some of that code.)
-This is a Linux device driver for the Sony CDU-535 CDROM drive.  This is
-one of the older Sony drives with its own interface card (Sony bus).
-The DOS driver for this drive is named SONY_CDU.SYS - when you boot DOS
-your drive should be identified as a SONY CDU-535.  The driver works
-with a CDU-531 also.  One user reported that the driver worked on drives
-OEM'ed by Procomm, drive and interface board were labelled Procomm.
-The Linux driver is based on Corey Minyard's sonycd 0.3 driver for
-the CDU-31A.  Ron Jeppesen just changed the commands that were sent
-to the drive to correspond to the CDU-535 commands and registers.
-There were enough changes to let bugs creep in but it seems to be stable.
-Ron was able to tar an entire CDROM (should read all blocks) and built
-ghostview and xfig off Walnut Creek's X11R5/GNU CDROM.  xcdplayer and
-workman work with the driver.  Others have used the driver without
-problems except those dealing with wait loops (fixed in third release).
-Like Minyard's original driver this one uses a polled interface (this
-is also the default setup for the DOS driver).  It has not been tried
-with interrupts or DMA enabled on the board.
-REQUIREMENTS
-============
-        - Sony CDU-535 drive, preferably without interrupts and DMA 
-          enabled on the card.
-        - Drive must be set up as unit 1.  Only the first unit will be 
-          recognized
-        - You must enter your interface address into 
-          /usr/src/linux/drivers/cdrom/sonycd535.h and build the
-          appropriate kernel or use the "kernel command line" parameter
-                sonycd535=0x320
-          with the correct interface address.
-NOTES:
-======
-1) The drive MUST be turned on when booting or it will not be recognized!
-   (but see comments on modularized version below)
-2) when the cdrom device is opened the eject button is disabled to keep the
-   user from ejecting a mounted disk and replacing it with another.
-   Unfortunately xcdplayer and workman also open the cdrom device so you
-   have to use the eject button in the software.  Keep this in mind if your
-   cdrom player refuses to give up its disk -- exit workman or xcdplayer, or
-   umount the drive if it has been mounted.
-THANKS
-======
-Many thanks to Ron Jeppesen (ronj.an@site007.saic.com) for getting
-this project off the ground.  He wrote the initial release
-and the first two patches to this driver (0.1, 0.2, and 0.3).
-Thanks also to Eberhard Moenkeberg (emoenke@gwdg.de) for prodding
-me to place this code into the mainstream Linux source tree
-(as of Linux version 1.1.91), as well as some patches to make
-it a better device citizen.  Further thanks to Joel Katz
-<joelkatz@webchat.org> for his MODULE patches (see details below),
-Porfiri Claudio <C.Porfiri@nisms.tei.ericsson.se> for patches
-to make the driver work with the older CDU-510/515 series, and
-Heiko Eissfeldt <heiko@colossus.escape.de> for pointing out that
-the verify_area() checks were ignoring the results of said checks
-(note: verify_area() has since been replaced by access_ok()).
-(Acknowledgments from Ron Jeppesen in the 0.3 release:)
-Thanks to Corey Minyard who wrote the original CDU-31A driver on which
-this driver is based.  Thanks to Ken Pizzini and Bob Blair who provided 
-patches and feedback on the first release of this driver.
-Ken Pizzini
-ken@halcyon.com
------------------------------------------------------------------------------
-(The following is from Joel Katz <joelkatz@webchat.org>.)
-        To build a version of sony535.o that can be installed as a module,
-use the following command:
-gcc -c -D__KERNEL__ -DMODULE -O2 sonycd535.c -o sonycd535.o
-        To install the module, simply type:
-insmod sony535.o
-        or
-insmod sony535.o sonycd535=<address>
-        And to remove it:
-rmmod sony535
-        The code checks to see if MODULE is defined and behaves as it used
-to if MODULE is not defined. That means your patched file should behave
-exactly as it used to if compiled into the kernel.
-        I have an external drive, and I usually leave it powered off. I used
-to have to reboot if I needed to use the CDROM drive. Now I don't.
-        Even if you have an internal drive, why waste the 96K of memory
-(unswappable) that the driver uses if you use your CD-ROM drive infrequently?
-        This driver will not install (whether compiled in or loaded as a
-module) if the CDROM drive is not available during its initialization. This
-means that you can have the driver compiled into the kernel and still load
-the module later (assuming the driver doesn't install itself during
-power-on). This only wastes 12K when you boot with the CDROM drive off.
-        This is what I usually do; I leave the driver compiled into the
-kernel, but load it as a module if I powered the system up with the drive
-off and then later decided to use the CDROM drive.
-        Since the driver only uses a single page to point to the chunks,
-attempting to set the buffer cache to more than 2 Megabytes would be very
-bad; don't do that.
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 4d880b3d1f35..3078f14830dd 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -34,7 +34,6 @@ parameter is applicable:
        APIC    APIC support is enabled.
        APM     Advanced Power Management support is enabled.
        AX25    Appropriate AX.25 support is enabled.
-        CD      Appropriate CD support is enabled.
        DRM     Direct Rendering Management support is enabled.
        EDD     BIOS Enhanced Disk Drive Services (EDD) is enabled
        EFI     EFI Partitioning (GPT) is enabled
@@ -326,9 +325,6 @@ and is between 256 and 4096 characters. It is defined in the file
        autotest        [IA64]
-        aztcd=          [HW,CD] Aztech CD268 CDROM driver
-                        Format: <io>,0x79 (?)
        baycom_epp=     [HW,AX25]
                        Format: <io>,<mode>
@@ -371,10 +367,6 @@ and is between 256 and 4096 characters. It is defined in the file
                        possible to determine what the correct size should be.
                        This option provides an override for these situations.
-        cdu31a=         [HW,CD]
-                        Format: <io>,<irq>[,PAS]
-                        See header of drivers/cdrom/cdu31a.c.
        chandev=        [HW,NET] Generic channel device initialisation
        checkreqprot    [SELINUX] Set initial checkreqprot flag value.
@@ -428,9 +420,6 @@ and is between 256 and 4096 characters. It is defined in the file
        hpet=           [IA-32,HPET] option to disable HPET and use PIT.
                        Format: disable
-        cm206=          [HW,CD]
-                        Format: { auto | [<io>,][<irq>] }
        com20020=       [HW,NET] ARCnet - COM20020 chipset
                        Format:
                        <io>[,<irq>[,<nodeID>[,<backplane>[,<ckp>[,<timeout>]]]]]
@@ -660,9 +649,6 @@ and is between 256 and 4096 characters. It is defined in the file
        gpt             [EFI] Forces disk with valid GPT signature but
                        invalid Protective MBR to be treated as GPT.
-        gscd=           [HW,CD]
-                        Format: <io>
        gvp11=          [HW,SCSI]
        hashdist=       [KNL,NUMA] Large hashes allocated during boot
@@ -826,9 +812,6 @@ and is between 256 and 4096 characters. It is defined in the file
                        tasks in the system -- can cause problems and
                        suboptimal load balancer performance.
-        isp16=          [HW,CD]
-                        Format: <io>,<irq>,<dma>,<setup>
        iucv=           [HW,NET]
        js=             [HW,JOY] Analog joystick
@@ -967,11 +950,6 @@ and is between 256 and 4096 characters. It is defined in the file
        mcatest=        [IA-64]
-        mcd=            [HW,CD]
-                        Format: <port>,<irq>,<mitsumi_bug_93_wait>
-        mcdx=           [HW,CD]
        mce             [IA-32] Machine Check Exception
        md=             [HW] RAID subsystems devices and level
@@ -1200,9 +1178,6 @@ and is between 256 and 4096 characters. It is defined in the file
        oprofile.timer= [HW]
                        Use timer interrupt instead of performance counters
-        optcd=          [HW,CD]
-                        Format: <io>
        osst=           [HW,SCSI] SCSI Tape Driver
                        Format: <buffer_size>,<write_threshold>
                        See also Documentation/scsi/st.txt.
@@ -1505,11 +1480,6 @@ and is between 256 and 4096 characters. It is defined in the file
        sbni=           [NET] Granch SBNI12 leased line adapter
-        sbpcd=          [HW,CD] Soundblaster CD adapter
-                        Format: <io>,<type>
-                        See a comment before function sbpcd_setup() in
-                        drivers/cdrom/sbpcd.c.
        sc1200wdt=      [HW,WDT] SC1200 WDT (watchdog) driver
                        Format: <io>[,<timeout>[,<isapnp>]]
@@ -1562,10 +1532,6 @@ and is between 256 and 4096 characters. It is defined in the file
        simeth=         [IA-64]
        simscsi=
-        sjcd=           [HW,CD]
-                        Format: <io>,<irq>,<dma>
-                        See header of drivers/cdrom/sjcd.c.
        slram=          [HW,MTD]
        slub_debug      [MM, SLUB]
@@ -1738,9 +1704,6 @@ and is between 256 and 4096 characters. It is defined in the file
        snd-ymfpci=     [HW,ALSA]
-        sonycd535=      [HW,CD]
-                        Format: <io>[,<irq>]
        sonypi.*=       [HW] Sony Programmable I/O Control Device driver
                        See Documentation/sonypi.txt