4 files changed, 45 insertions, 4 deletions

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 736d45602886..e7848a0d99eb 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -199,6 +199,10 @@ and is between 256 and 4096 characters. It is defined in the file
                         acpi_display_output=video
                         See above.
 
+        acpi_early_pdc_eval     [HW,ACPI] Evaluate processor _PDC methods
+                                early. Needed on some platforms to properly
+                                initialize the EC.
+
         acpi_irq_balance [HW,ACPI]
                         ACPI will balance active IRQs
                         default in APIC mode
@@ -311,6 +315,11 @@ and is between 256 and 4096 characters. It is defined in the file
         aic79xx=        [HW,SCSI]
                         See Documentation/scsi/aic79xx.txt.
 
+        alignment=      [KNL,ARM]
+                        Allow the default userspace alignment fault handler
+                        behaviour to be specified.  Bit 0 enables warnings,
+                        bit 1 enables fixups, and bit 2 sends a segfault.
+
         amd_iommu=      [HW,X86-84]
                         Pass parameters to the AMD IOMMU driver in the system.
                         Possible values are:
diff --git a/Documentation/networking/ip-sysctl.txt b/Documentation/networking/ip-sysctl.txt
index 006b39dec87d..e87f3cdc8a6a 100644
--- a/Documentation/networking/ip-sysctl.txt
+++ b/Documentation/networking/ip-sysctl.txt
@@ -1074,10 +1074,10 @@ regen_max_retry - INTEGER
         Default: 5
 
 max_addresses - INTEGER
-        Number of maximum addresses per interface.  0 disables limitation.
-        It is recommended not set too large value (or 0) because it would
-        be too easy way to crash kernel to allow to create too much of
-        autoconfigured addresses.
+        Maximum number of autoconfigured addresses per interface.  Setting
+        to zero disables the limitation.  It is not recommended to set this
+        value too large (or to zero) because it would be an easy way to
+        crash the kernel by allowing too many addresses to be created.
         Default: 16
 
 disable_ipv6 - BOOLEAN
diff --git a/Documentation/sound/alsa/HD-Audio-Models.txt b/Documentation/sound/alsa/HD-Audio-Models.txt
index e72cee9e2a71..1d38b0dfba95 100644
--- a/Documentation/sound/alsa/HD-Audio-Models.txt
+++ b/Documentation/sound/alsa/HD-Audio-Models.txt
@@ -124,6 +124,8 @@ ALC882/883/885/888/889
   asus-a7m      ASUS A7M
   macpro        MacPro support
   mb5           Macbook 5,1
+  macmini3      Macmini 3,1
+  mba21         Macbook Air 2,1
   mbp3          Macbook Pro rev3
   imac24        iMac 24'' with jack detection
   imac91        iMac 9,1
@@ -279,13 +281,16 @@ Conexant 5051
   laptop        Basic Laptop config (default)
   hp            HP Spartan laptop
   hp-dv6736     HP dv6736
+  hp-f700       HP Compaq Presario F700
   lenovo-x200   Lenovo X200 laptop
+  toshiba       Toshiba Satellite M300
 
 Conexant 5066
 =============
   laptop        Basic Laptop config (default)
   dell-laptop   Dell laptops
   olpc-xo-1_5   OLPC XO 1.5
+  ideapad       Lenovo IdeaPad U150
 
 STAC9200
 ========
diff --git a/Documentation/sound/alsa/HD-Audio.txt b/Documentation/sound/alsa/HD-Audio.txt
index 6325bec06a72..f4dd3bf99d12 100644
--- a/Documentation/sound/alsa/HD-Audio.txt
+++ b/Documentation/sound/alsa/HD-Audio.txt
@@ -452,6 +452,33 @@ Similarly, the lines after `[verb]` are parsed as `init_verbs`
 sysfs entries, and the lines after `[hint]` are parsed as `hints`
 sysfs entries, respectively.
 
+Another example to override the codec vendor id from 0x12345678 to
+0xdeadbeef is like below:
+------------------------------------------------------------------------
+  [codec]
+  0x12345678 0xabcd1234 2
+
+  [vendor_id]
+  0xdeadbeef
+------------------------------------------------------------------------
+
+In the similar way, you can override the codec subsystem_id via
+`[subsystem_id]`, the revision id via `[revision_id]` line.
+Also, the codec chip name can be rewritten via `[chip_name]` line.
+------------------------------------------------------------------------
+  [codec]
+  0x12345678 0xabcd1234 2
+
+  [subsystem_id]
+  0xffff1111
+
+  [revision_id]
+  0x10
+
+  [chip_name]
+  My-own NEWS-0002
+------------------------------------------------------------------------
+
 The hd-audio driver reads the file via request_firmware().  Thus,
 a patch file has to be located on the appropriate firmware path,
 typically, /lib/firmware.  For example, when you pass the option