3 files changed, 90 insertions, 42 deletions

diff --git a/Documentation/i386/IO-APIC.txt b/Documentation/i386/IO-APIC.txt
index 435e69e6e9aa..f95166645d29 100644
--- a/Documentation/i386/IO-APIC.txt
+++ b/Documentation/i386/IO-APIC.txt
@@ -1,12 +1,14 @@
 Most (all) Intel-MP compliant SMP boards have the so-called 'IO-APIC',
-which is an enhanced interrupt controller, it enables us to route
-hardware interrupts to multiple CPUs, or to CPU groups.
+which is an enhanced interrupt controller. It enables us to route
+hardware interrupts to multiple CPUs, or to CPU groups. Without an
+IO-APIC, interrupts from hardware will be delivered only to the
+CPU which boots the operating system (usually CPU#0).
 
 Linux supports all variants of compliant SMP boards, including ones with
-multiple IO-APICs. (multiple IO-APICs are used in high-end servers to
-distribute IRQ load further).
+multiple IO-APICs. Multiple IO-APICs are used in high-end servers to
+distribute IRQ load further.
 
-There are (a few) known breakages in certain older boards, which bugs are
+There are (a few) known breakages in certain older boards, such bugs are
 usually worked around by the kernel. If your MP-compliant SMP board does
 not boot Linux, then consult the linux-smp mailing list archives first.
 
@@ -28,18 +30,18 @@ If your box boots fine with enabled IO-APIC IRQs, then your
   hell:~>
   <----------------------------
 
-some interrupts are still listed as 'XT PIC', but this is not a problem,
+Some interrupts are still listed as 'XT PIC', but this is not a problem;
 none of those IRQ sources is performance-critical.
 
 
-in the unlikely case that your board does not create a working mp-table,
+In the unlikely case that your board does not create a working mp-table,
 you can use the pirq= boot parameter to 'hand-construct' IRQ entries. This
-is nontrivial though and cannot be automated. One sample /etc/lilo.conf
+is non-trivial though and cannot be automated. One sample /etc/lilo.conf
 entry:
 
         append="pirq=15,11,10"
 
-the actual numbers depend on your system, on your PCI cards and on their
+The actual numbers depend on your system, on your PCI cards and on their
 PCI slot position. Usually PCI slots are 'daisy chained' before they are
 connected to the PCI chipset IRQ routing facility (the incoming PIRQ1-4
 lines):
@@ -54,7 +56,7 @@ lines):
      PIRQ1 ----| |-  `----| |-  `----| |-  `----| |--------| |
                `-'        `-'        `-'        `-'        `-'
 
-every PCI card emits a PCI IRQ, which can be INTA,INTB,INTC,INTD:
+Every PCI card emits a PCI IRQ, which can be INTA, INTB, INTC or INTD:
 
                                ,-.
                          INTD--| |
@@ -95,21 +97,21 @@ card (IRQ11) in Slot3, and have Slot1 empty:
 [value '0' is a generic 'placeholder', reserved for empty (or non-IRQ emitting)
 slots.]
 
-generally, it's always possible to find out the correct pirq= settings, just
+Generally, it's always possible to find out the correct pirq= settings, just
 permute all IRQ numbers properly ... it will take some time though. An
 'incorrect' pirq line will cause the booting process to hang, or a device
-won't function properly (if it's inserted as eg. a module).
+won't function properly (e.g. if it's inserted as a module).
 
-If you have 2 PCI buses, then you can use up to 8 pirq values. Although such
+If you have 2 PCI buses, then you can use up to 8 pirq values, although such
 boards tend to have a good configuration.
 
 Be prepared that it might happen that you need some strange pirq line:
 
         append="pirq=0,0,0,0,0,0,9,11"
 
-use smart try-and-err techniques to find out the correct pirq line ...
+Use smart trial-and-error techniques to find out the correct pirq line ...
 
-good luck and mail to linux-smp@vger.kernel.org or
+Good luck and mail to linux-smp@vger.kernel.org or
 linux-kernel@vger.kernel.org if you have any problems that are not covered
 by this document.
 
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index a4fc7fc21439..9a5b6658c65e 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -950,6 +950,41 @@ and is between 256 and 4096 characters. It is defined in the file
                         when set.
                         Format: <int>
 
+        libata.force=   [LIBATA] Force configurations.  The format is comma
+                        separated list of "[ID:]VAL" where ID is
+                        PORT[:DEVICE].  PORT and DEVICE are decimal numbers
+                        matching port, link or device.  Basically, it matches
+                        the ATA ID string printed on console by libata.  If
+                        the whole ID part is omitted, the last PORT and DEVICE
+                        values are used.  If ID hasn't been specified yet, the
+                        configuration applies to all ports, links and devices.
+
+                        If only DEVICE is omitted, the parameter applies to
+                        the port and all links and devices behind it.  DEVICE
+                        number of 0 either selects the first device or the
+                        first fan-out link behind PMP device.  It does not
+                        select the host link.  DEVICE number of 15 selects the
+                        host link and device attached to it.
+
+                        The VAL specifies the configuration to force.  As long
+                        as there's no ambiguity shortcut notation is allowed.
+                        For example, both 1.5 and 1.5G would work for 1.5Gbps.
+                        The following configurations can be forced.
+
+                        * Cable type: 40c, 80c, short40c, unk, ign or sata.
+                          Any ID with matching PORT is used.
+
+                        * SATA link speed limit: 1.5Gbps or 3.0Gbps.
+
+                        * Transfer mode: pio[0-7], mwdma[0-4] and udma[0-7].
+                          udma[/][16,25,33,44,66,100,133] notation is also
+                          allowed.
+
+                        * [no]ncq: Turn on or off NCQ.
+
+                        If there are multiple matching configurations changing
+                        the same attribute, the last one is used.
+
         load_ramdisk=   [RAM] List of ramdisks to load from floppy
                         See Documentation/ramdisk.txt.
 
@@ -1056,8 +1091,6 @@ and is between 256 and 4096 characters. It is defined in the file
                         [SCSI] Maximum number of LUNs received.
                         Should be between 1 and 16384.
 
-        mca-pentium     [BUGS=X86-32]
-
         mcatest=        [IA-64]
 
         mce             [X86-32] Machine Check Exception
diff --git a/Documentation/laptops/thinkpad-acpi.txt b/Documentation/laptops/thinkpad-acpi.txt
index 6c2477754a2a..76cb428435da 100644
--- a/Documentation/laptops/thinkpad-acpi.txt
+++ b/Documentation/laptops/thinkpad-acpi.txt
@@ -160,7 +160,7 @@ Hot keys
 procfs: /proc/acpi/ibm/hotkey
 sysfs device attribute: hotkey_*
 
-In a ThinkPad, the ACPI HKEY handler is responsible for comunicating
+In a ThinkPad, the ACPI HKEY handler is responsible for communicating
 some important events and also keyboard hot key presses to the operating
 system.  Enabling the hotkey functionality of thinkpad-acpi signals the
 firmware that such a driver is present, and modifies how the ThinkPad
@@ -193,7 +193,7 @@ Not all bits in the mask can be modified.  Not all bits that can be
 modified do anything.  Not all hot keys can be individually controlled
 by the mask.  Some models do not support the mask at all, and in those
 models, hot keys cannot be controlled individually.  The behaviour of
-the mask is, therefore, higly dependent on the ThinkPad model.
+the mask is, therefore, highly dependent on the ThinkPad model.
 
 Note that unmasking some keys prevents their default behavior.  For
 example, if Fn+F5 is unmasked, that key will no longer enable/disable
@@ -288,7 +288,7 @@ sysfs notes:
                 in ACPI event mode, volume up/down/mute are reported as
                 separate events, but this behaviour may be corrected in
                 future releases of this driver, in which case the
-                ThinkPad volume mixer user interface semanthics will be
+                ThinkPad volume mixer user interface semantics will be
                 enforced.
 
         hotkey_poll_freq:
@@ -306,13 +306,20 @@ sysfs notes:
                 The recommended polling frequency is 10Hz.
 
         hotkey_radio_sw:
-                if the ThinkPad has a hardware radio switch, this
+                If the ThinkPad has a hardware radio switch, this
                 attribute will read 0 if the switch is in the "radios
-                disabled" postition, and 1 if the switch is in the
+                disabled" position, and 1 if the switch is in the
                 "radios enabled" position.
 
                 This attribute has poll()/select() support.
 
+        hotkey_tablet_mode:
+                If the ThinkPad has tablet capabilities, this attribute
+                will read 0 if the ThinkPad is in normal mode, and
+                1 if the ThinkPad is in tablet mode.
+
+                This attribute has poll()/select() support.
+
         hotkey_report_mode:
                 Returns the state of the procfs ACPI event report mode
                 filter for hot keys.  If it is set to 1 (the default),
@@ -339,7 +346,7 @@ sysfs notes:
         wakeup_hotunplug_complete:
                 Set to 1 if the system was waken up because of an
                 undock or bay ejection request, and that request
-                was sucessfully completed.  At this point, it might
+                was successfully completed.  At this point, it might
                 be useful to send the system back to sleep, at the
                 user's choice.  Refer to HKEY events 0x4003 and
                 0x3003, below.
@@ -392,7 +399,7 @@ event	code	Key		Notes
                                 Lenovo: battery
 
 0x1004  0x03    FN+F4           Sleep button (ACPI sleep button
-                                semanthics, i.e. sleep-to-RAM).
+                                semantics, i.e. sleep-to-RAM).
                                 It is always generate some kind
                                 of event, either the hot key
                                 event or a ACPI sleep button
@@ -403,12 +410,12 @@ event	code	Key		Notes
                                 time passes.
 
 0x1005  0x04    FN+F5           Radio.  Enables/disables
-                                the internal BlueTooth hardware
+                                the internal Bluetooth hardware
                                 and W-WAN card if left in control
                                 of the firmware.  Does not affect
                                 the WLAN card.
                                 Should be used to turn on/off all
-                                radios (bluetooth+W-WAN+WLAN),
+                                radios (Bluetooth+W-WAN+WLAN),
                                 really.
 
 0x1006  0x05    FN+F6           -
@@ -417,7 +424,7 @@ event	code	Key		Notes
                                 Do you feel lucky today?
 
 0x1008  0x07    FN+F8           IBM: toggle screen expand
-                                Lenovo: configure ultranav
+                                Lenovo: configure UltraNav
 
 0x1009  0x08    FN+F9           -
         ..      ..              ..
@@ -447,7 +454,7 @@ event	code	Key		Notes
 0x1011  0x10    FN+END          Brightness down.  See brightness
                                 up for details.
 
-0x1012  0x11    FN+PGUP         Thinklight toggle.  This key is
+0x1012  0x11    FN+PGUP         ThinkLight toggle.  This key is
                                 always handled by the firmware,
                                 even when unmasked.
 
@@ -469,7 +476,7 @@ event	code	Key		Notes
                                 key is always handled by the
                                 firmware, even when unmasked.
 
-0x1018  0x17    THINKPAD        Thinkpad/Access IBM/Lenovo key
+0x1018  0x17    THINKPAD        ThinkPad/Access IBM/Lenovo key
 
 0x1019  0x18    unknown
 ..      ..      ..
@@ -488,9 +495,17 @@ If a key is mapped to KEY_UNKNOWN, it generates an input event that
 includes an scan code.  If a key is mapped to anything else, it will
 generate input device EV_KEY events.
 
+In addition to the EV_KEY events, thinkpad-acpi may also issue EV_SW
+events for switches:
+
+SW_RADIO        T60 and later hardare rfkill rocker switch
+SW_TABLET_MODE  Tablet ThinkPads HKEY events 0x5009 and 0x500A
+
 Non hot-key ACPI HKEY event map:
 0x5001          Lid closed
 0x5002          Lid opened
+0x5009          Tablet swivel: switched to tablet mode
+0x500A          Tablet swivel: switched to normal mode
 0x7000          Radio Switch may have changed state
 
 The above events are not propagated by the driver, except for legacy
@@ -505,9 +520,7 @@ The above events are never propagated by the driver.
 
 0x3003          Bay ejection (see 0x2x05) complete, can sleep again
 0x4003          Undocked (see 0x2x04), can sleep again
-0x5009          Tablet swivel: switched to tablet mode
-0x500A          Tablet swivel: switched to normal mode
-0x500B          Tablet pen insterted into its storage bay
+0x500B          Tablet pen inserted into its storage bay
 0x500C          Tablet pen removed from its storage bay
 0x5010          Brightness level changed (newer Lenovo BIOSes)
 
@@ -539,7 +552,7 @@ sysfs (it is read-only).
 If the hotkey_report_mode module parameter is set to 1 or 2, it cannot
 be changed later through sysfs (any writes will return -EPERM to signal
 that hotkey_report_mode was locked.  On 2.6.23 and later, where
-hotkey_report_mode cannot be changed at all, writes will return -EACES).
+hotkey_report_mode cannot be changed at all, writes will return -EACCES).
 
 hotkey_report_mode set to 1 makes the driver export through the procfs
 ACPI event interface all hot key presses (which are *also* sent to the
@@ -584,7 +597,7 @@ Sysfs notes:
                 0: disables Bluetooth / Bluetooth is disabled
                 1: enables Bluetooth / Bluetooth is enabled.
 
-        Note: this interface will be probably be superseeded by the
+        Note: this interface will be probably be superseded by the
         generic rfkill class, so it is NOT to be considered stable yet.
 
 Video output control -- /proc/acpi/ibm/video
@@ -791,12 +804,12 @@ on the X40 (tpb is the ThinkPad Buttons utility):
         1 - Related to "Volume up" key press
         2 - Related to "Mute on" key press
         3 - Related to "Access IBM" key press
-        4 - Related to "LCD brightness up" key pess
+        4 - Related to "LCD brightness up" key press
         5 - Related to "LCD brightness down" key press
         11 - Related to "toggle screen expansion" key press/function
         12 - Related to "ThinkLight on"
         13 - Related to "ThinkLight off"
-        14 - Related to "ThinkLight" key press (toggle thinklight)
+        14 - Related to "ThinkLight" key press (toggle ThinkLight)
 
 The cmos command interface is prone to firmware split-brain problems, as
 in newer ThinkPads it is just a compatibility layer.  Do not use it, it is
@@ -1024,7 +1037,7 @@ There are two interfaces to the firmware for direct brightness control,
 EC and CMOS.  To select which one should be used, use the
 brightness_mode module parameter: brightness_mode=1 selects EC mode,
 brightness_mode=2 selects CMOS mode, brightness_mode=3 selects both EC
-and CMOS.  The driver tries to autodetect which interface to use.
+and CMOS.  The driver tries to auto-detect which interface to use.
 
 When display backlight brightness controls are available through the
 standard ACPI interface, it is best to use it instead of this direct
@@ -1266,8 +1279,8 @@ experimental=1 parameter when loading the module.
 This feature shows the presence and current state of a W-WAN (Sierra
 Wireless EV-DO) device.
 
-It was tested on a Lenovo Thinkpad X60. It should probably work on other
-Thinkpad models which come with this module installed.
+It was tested on a Lenovo ThinkPad X60. It should probably work on other
+ThinkPad models which come with this module installed.
 
 Procfs notes:
 
@@ -1286,7 +1299,7 @@ Sysfs notes:
                 0: disables WWAN card / WWAN card is disabled
                 1: enables WWAN card / WWAN card is enabled.
 
-        Note: this interface will be probably be superseeded by the
+        Note: this interface will be probably be superseded by the
         generic rfkill class, so it is NOT to be considered stable yet.
 
 Multiple Commands, Module Parameters
@@ -1309,7 +1322,7 @@ Enabling debugging output
 The module takes a debug parameter which can be used to selectively
 enable various classes of debugging output, for example:
 
-         modprobe ibm_acpi debug=0xffff
+         modprobe thinkpad_acpi debug=0xffff
 
 will enable all debugging output classes.  It takes a bitmask, so
 to enable more than one output class, just add their values.
@@ -1356,7 +1369,7 @@ Sysfs interface changelog:
                 NVRAM is compiled out by the user because it is
                 unneeded/undesired in the first place).
 0x020101:       Marker for thinkpad-acpi with hot key NVRAM polling
-                and proper hotkey_mask semanthics (version 8 of the
+                and proper hotkey_mask semantics (version 8 of the
                 NVRAM polling patch).  Some development snapshots of
                 0.18 had an earlier version that did strange things
                 to hotkey_mask.