11 files changed, 1017 insertions, 300 deletions

diff --git a/Documentation/BUG-HUNTING b/Documentation/BUG-HUNTING
index ca29242dbc38..65b97e1dbf70 100644
--- a/Documentation/BUG-HUNTING
+++ b/Documentation/BUG-HUNTING
@@ -1,3 +1,56 @@
+Table of contents
+=================
+
+Last updated: 20 December 2005
+
+Contents
+========
+
+- Introduction
+- Devices not appearing
+- Finding patch that caused a bug
+-- Finding using git-bisect
+-- Finding it the old way
+- Fixing the bug
+
+Introduction
+============
+
+Always try the latest kernel from kernel.org and build from source. If you are
+not confident in doing that please report the bug to your distribution vendor
+instead of to a kernel developer.
+
+Finding bugs is not always easy. Have a go though. If you can't find it don't
+give up. Report as much as you have found to the relevant maintainer. See
+MAINTAINERS for who that is for the subsystem you have worked on.
+
+Before you submit a bug report read REPORTING-BUGS.
+
+Devices not appearing
+=====================
+
+Often this is caused by udev. Check that first before blaming it on the
+kernel.
+
+Finding patch that caused a bug
+===============================
+
+
+
+Finding using git-bisect
+------------------------
+
+Using the provided tools with git makes finding bugs easy provided the bug is
+reproducible.
+
+Steps to do it:
+- start using git for the kernel source
+- read the man page for git-bisect
+- have fun
+
+Finding it the old way
+----------------------
+
 [Sat Mar  2 10:32:33 PST 1996 KERNEL_BUG-HOWTO lm@sgi.com (Larry McVoy)]
 
 This is how to track down a bug if you know nothing about kernel hacking.  
@@ -90,3 +143,63 @@ it does work and it lets non-hackers help fix bugs.  And it is cool
 because Linux snapshots will let you do this - something that you can't
 do with vendor supplied releases.
 
+Fixing the bug
+==============
+
+Nobody is going to tell you how to fix bugs. Seriously. You need to work it
+out. But below are some hints on how to use the tools.
+
+To debug a kernel, use objdump and look for the hex offset from the crash
+output to find the valid line of code/assembler. Without debug symbols, you
+will see the assembler code for the routine shown, but if your kernel has
+debug symbols the C code will also be available. (Debug symbols can be enabled
+in the kernel hacking menu of the menu configuration.) For example:
+
+    objdump -r -S -l --disassemble net/dccp/ipv4.o
+
+NB.: you need to be at the top level of the kernel tree for this to pick up
+your C files.
+
+If you don't have access to the code you can also debug on some crash dumps
+e.g. crash dump output as shown by Dave Miller.
+
+>    EIP is at ip_queue_xmit+0x14/0x4c0
+>     ...
+>    Code: 44 24 04 e8 6f 05 00 00 e9 e8 fe ff ff 8d 76 00 8d bc 27 00 00
+>    00 00 55 57  56 53 81 ec bc 00 00 00 8b ac 24 d0 00 00 00 8b 5d 08
+>    <8b> 83 3c 01 00 00 89 44  24 14 8b 45 28 85 c0 89 44 24 18 0f 85
+>
+>    Put the bytes into a "foo.s" file like this:
+>
+>           .text
+>           .globl foo
+>    foo:
+>           .byte  .... /* bytes from Code: part of OOPS dump */
+>
+>    Compile it with "gcc -c -o foo.o foo.s" then look at the output of
+>    "objdump --disassemble foo.o".
+>
+>    Output:
+>
+>    ip_queue_xmit:
+>        push       %ebp
+>        push       %edi
+>        push       %esi
+>        push       %ebx
+>        sub        $0xbc, %esp
+>        mov        0xd0(%esp), %ebp        ! %ebp = arg0 (skb)
+>        mov        0x8(%ebp), %ebx         ! %ebx = skb->sk
+>        mov        0x13c(%ebx), %eax       ! %eax = inet_sk(sk)->opt
+
+Another very useful option of the Kernel Hacking section in menuconfig is
+Debug memory allocations. This will help you see whether data has been
+initialised and not set before use etc. To see the values that get assigned
+with this look at mm/slab.c and search for POISON_INUSE. When using this an
+Oops will often show the poisoned data instead of zero which is the default.
+
+Once you have worked out a fix please submit it upstream. After all open
+source is about sharing what you do and don't you want to be recognised for
+your genius?
+
+Please do read Documentation/SubmittingPatches though to help your code get
+accepted.
diff --git a/Documentation/dvb/get_dvb_firmware b/Documentation/dvb/get_dvb_firmware
index bb55f49f2745..15fc8fbef67e 100644
--- a/Documentation/dvb/get_dvb_firmware
+++ b/Documentation/dvb/get_dvb_firmware
@@ -246,7 +246,7 @@ sub vp7041 {
 }
 
 sub dibusb {
-        my $url = "http://www.linuxtv.org/downloads/firmware/dvb-dibusb-5.0.0.11.fw";
+        my $url = "http://www.linuxtv.org/downloads/firmware/dvb-usb-dibusb-5.0.0.11.fw";
         my $outfile = "dvb-dibusb-5.0.0.11.fw";
         my $hash = "fa490295a527360ca16dcdf3224ca243";
 
diff --git a/Documentation/filesystems/isofs.txt b/Documentation/filesystems/isofs.txt
index 424585ff6ea1..758e50401c16 100644
--- a/Documentation/filesystems/isofs.txt
+++ b/Documentation/filesystems/isofs.txt
@@ -9,9 +9,9 @@ when using discs encoded using Microsoft's Joliet extensions.
   iocharset=name Character set to use for converting from Unicode to
                 ASCII.  Joliet filenames are stored in Unicode format, but
                 Unix for the most part doesn't know how to deal with Unicode.
-                There is also an option of doing UTF8 translations with the
+                There is also an option of doing UTF-8 translations with the
                 utf8 option.
-  utf8          Encode Unicode names in UTF8 format. Default is no.
+  utf8          Encode Unicode names in UTF-8 format. Default is no.
 
 Mount options unique to the isofs filesystem.
   block=512     Set the block size for the disk to 512 bytes
diff --git a/Documentation/filesystems/jfs.txt b/Documentation/filesystems/jfs.txt
index 3e992daf99ad..bae128663748 100644
--- a/Documentation/filesystems/jfs.txt
+++ b/Documentation/filesystems/jfs.txt
@@ -6,7 +6,7 @@ The following mount options are supported:
 
 iocharset=name  Character set to use for converting from Unicode to
                 ASCII.  The default is to do no conversion.  Use
-                iocharset=utf8 for UTF8 translations.  This requires
+                iocharset=utf8 for UTF-8 translations.  This requires
                 CONFIG_NLS_UTF8 to be set in the kernel .config file.
                 iocharset=none specifies the default behavior explicitly.
 
diff --git a/Documentation/filesystems/vfat.txt b/Documentation/filesystems/vfat.txt
index 5ead20c6c744..2001abbc60e6 100644
--- a/Documentation/filesystems/vfat.txt
+++ b/Documentation/filesystems/vfat.txt
@@ -28,16 +28,16 @@ iocharset=name -- Character set to use for converting between the
                  know how to deal with Unicode.
                  By default, FAT_DEFAULT_IOCHARSET setting is used.
 
-                 There is also an option of doing UTF8 translations
+                 There is also an option of doing UTF-8 translations
                  with the utf8 option.
 
                  NOTE: "iocharset=utf8" is not recommended. If unsure,
                  you should consider the following option instead.
 
-utf8=<bool>   -- UTF8 is the filesystem safe version of Unicode that
+utf8=<bool>   -- UTF-8 is the filesystem safe version of Unicode that
                  is used by the console.  It can be be enabled for the
                  filesystem with this option. If 'uni_xlate' gets set,
-                 UTF8 gets disabled.
+                 UTF-8 gets disabled.
 
 uni_xlate=<bool> -- Translate unhandled Unicode characters to special
                  escaped sequences.  This would let you backup and
diff --git a/Documentation/networking/e100.txt b/Documentation/networking/e100.txt
index 4ef9f7cd5dc3..944aa55e79f8 100644
--- a/Documentation/networking/e100.txt
+++ b/Documentation/networking/e100.txt
@@ -1,16 +1,17 @@
 Linux* Base Driver for the Intel(R) PRO/100 Family of Adapters
 ==============================================================
 
-November 17, 2004
-
+November 15, 2005
 
 Contents
 ========
 
 - In This Release
 - Identifying Your Adapter
+- Building and Installation
 - Driver Configuration Parameters
 - Additional Configurations
+- Known Issues
 - Support
 
 
@@ -18,18 +19,30 @@ In This Release
 ===============
 
 This file describes the Linux* Base Driver for the Intel(R) PRO/100 Family of
-Adapters, version 3.3.x.  This driver supports 2.4.x and 2.6.x kernels. 
+Adapters. This driver includes support for Itanium(R)2-based systems.
+
+For questions related to hardware requirements, refer to the documentation
+supplied with your Intel PRO/100 adapter.
+
+The following features are now available in supported kernels:
+ - Native VLANs
+ - Channel Bonding (teaming)
+ - SNMP
+
+Channel Bonding documentation can be found in the Linux kernel source:
+/Documentation/networking/bonding.txt
+
 
 Identifying Your Adapter
 ========================
 
-For more information on how to identify your adapter, go to the Adapter & 
+For more information on how to identify your adapter, go to the Adapter &
 Driver ID Guide at:
 
   http://support.intel.com/support/network/adapter/pro100/21397.htm
 
-For the latest Intel network drivers for Linux, refer to the following 
-website. In the search field, enter your adapter name or type, or use the 
+For the latest Intel network drivers for Linux, refer to the following
+website. In the search field, enter your adapter name or type, or use the
 networking link on the left to search for your adapter:
 
   http://downloadfinder.intel.com/scripts-df/support_intel.asp
@@ -40,73 +53,75 @@ Driver Configuration Parameters
 The default value for each parameter is generally the recommended setting,
 unless otherwise noted.
 
-Rx Descriptors: Number of receive descriptors. A receive descriptor is a data 
-   structure that describes a receive buffer and its attributes to the network 
-   controller. The data in the descriptor is used by the controller to write 
-   data from the controller to host memory. In the 3.0.x driver the valid
-   range for this parameter is 64-256. The default value is 64. This parameter 
-   can be changed using the command 
- 
+Rx Descriptors: Number of receive descriptors. A receive descriptor is a data
+   structure that describes a receive buffer and its attributes to the network
+   controller. The data in the descriptor is used by the controller to write
+   data from the controller to host memory. In the 3.x.x driver the valid range
+   for this parameter is 64-256. The default value is 64. This parameter can be
+   changed using the command:
+
    ethtool -G eth? rx n, where n is the number of desired rx descriptors.
 
-Tx Descriptors: Number of transmit descriptors. A transmit descriptor is a
-   data structure that describes a transmit buffer and its attributes to the
-   network controller. The data in the descriptor is used by the controller to 
-   read data from the host memory to the controller. In the 3.0.x driver the 
-   valid range for this parameter is 64-256. The default value is 64. This 
-   parameter can be changed using the command 
+Tx Descriptors: Number of transmit descriptors. A transmit descriptor is a data
+   structure that describes a transmit buffer and its attributes to the network
+   controller. The data in the descriptor is used by the controller to read
+   data from the host memory to the controller. In the 3.x.x driver the valid
+   range for this parameter is 64-256. The default value is 64. This parameter
+   can be changed using the command:
 
    ethtool -G eth? tx n, where n is the number of desired tx descriptors.
 
-Speed/Duplex: The driver auto-negotiates the link speed and duplex settings by 
-   default. Ethtool can be used as follows to force speed/duplex. 
+Speed/Duplex: The driver auto-negotiates the link speed and duplex settings by
+   default. Ethtool can be used as follows to force speed/duplex.
 
    ethtool -s eth?  autoneg off speed {10|100} duplex {full|half}
 
    NOTE: setting the speed/duplex to incorrect values will cause the link to
    fail.
 
-Event Log Message Level:  The driver uses the message level flag to log events 
-   to syslog. The message level can be set at driver load time. It can also be 
-   set using the command
+Event Log Message Level:  The driver uses the message level flag to log events
+   to syslog. The message level can be set at driver load time. It can also be
+   set using the command:
 
    ethtool -s eth? msglvl n
 
+
 Additional Configurations
 =========================
 
   Configuring the Driver on Different Distributions
   -------------------------------------------------
 
-  Configuring a network driver to load properly when the system is started is 
-  distribution dependent. Typically, the configuration process involves adding 
-  an alias line to /etc/modules.conf as well as editing other system startup 
-  scripts and/or configuration files.  Many popular Linux distributions ship 
-  with tools to make these changes for you. To learn the proper way to 
-  configure a network device for your system, refer to your distribution 
-  documentation. If during this process you are asked for the driver or module 
-  name, the name for the Linux Base Driver for the Intel PRO/100 Family of 
-  Adapters is e100.
+  Configuring a network driver to load properly when the system is started is
+  distribution dependent. Typically, the configuration process involves adding
+  an alias line to /etc/modules.conf or /etc/modprobe.conf as well as editing
+  other system startup scripts and/or configuration files.  Many popular Linux
+  distributions ship with tools to make these changes for you. To learn the
+  proper way to configure a network device for your system, refer to your
+  distribution documentation.  If during this process you are asked for the
+  driver or module name, the name for the Linux Base Driver for the Intel
+  PRO/100 Family of Adapters is e100.
 
-  As an example, if you install the e100 driver for two PRO/100 adapters 
-  (eth0 and eth1), add the following to modules.conf:
+  As an example, if you install the e100 driver for two PRO/100 adapters
+  (eth0 and eth1), add the following to modules.conf or modprobe.conf:
 
        alias eth0 e100
        alias eth1 e100
 
   Viewing Link Messages
   ---------------------
-  In order to see link messages and other Intel driver information on your 
-  console, you must set the dmesg level up to six. This can be done by 
-  entering the following on the command line before loading the e100 driver: 
+  In order to see link messages and other Intel driver information on your
+  console, you must set the dmesg level up to six. This can be done by
+  entering the following on the command line before loading the e100 driver:
 
        dmesg -n 8
 
-  If you wish to see all messages issued by the driver, including debug 
+  If you wish to see all messages issued by the driver, including debug
   messages, set the dmesg level to eight.
 
   NOTE: This setting is not saved across reboots.
 
+
   Ethtool
   -------
 
@@ -114,29 +129,27 @@ Additional Configurations
   diagnostics, as well as displaying statistical information.  Ethtool
   version 1.6 or later is required for this functionality.
 
-  The latest release of ethtool can be found at:
-  http://sf.net/projects/gkernel.  
+  The latest release of ethtool can be found from
+  http://sourceforge.net/projects/gkernel.
 
-  NOTE: This driver uses mii support from the kernel. As a result, when 
-  there is no link, ethtool will report speed/duplex to be 10/half.
+  NOTE: Ethtool 1.6 only supports a limited set of ethtool options. Support
+  for a more complete ethtool feature set can be enabled by upgrading
+  ethtool to ethtool-1.8.1.
 
-  NOTE: Ethtool 1.6 only supports a limited set of ethtool options. Support 
-  for a more complete ethtool feature set can be enabled by upgrading 
-  ethtool to ethtool-1.8.1. 
 
   Enabling Wake on LAN* (WoL)
   ---------------------------
-  WoL is provided through the Ethtool* utility. Ethtool is included with Red 
-  Hat* 8.0. For other Linux distributions, download and install Ethtool from 
-  the following website: http://sourceforge.net/projects/gkernel. 
+  WoL is provided through the Ethtool* utility. Ethtool is included with Red
+  Hat* 8.0. For other Linux distributions, download and install Ethtool from
+  the following website: http://sourceforge.net/projects/gkernel.
 
-  For instructions on enabling WoL with Ethtool, refer to the Ethtool man
-  page.
+  For instructions on enabling WoL with Ethtool, refer to the Ethtool man page.
 
   WoL will be enabled on the system during the next shut down or reboot. For
-  this driver version, in order to enable WoL, the e100 driver must be 
+  this driver version, in order to enable WoL, the e100 driver must be
   loaded when shutting down or rebooting the system.
 
+
   NAPI
   ----
 
@@ -144,6 +157,25 @@ Additional Configurations
 
   See www.cyberus.ca/~hadi/usenix-paper.tgz for more information on NAPI.
 
+  Multiple Interfaces on Same Ethernet Broadcast Network
+  ------------------------------------------------------
+
+  Due to the default ARP behavior on Linux, it is not possible to have
+  one system on two IP networks in the same Ethernet broadcast domain
+  (non-partitioned switch) behave as expected. All Ethernet interfaces
+  will respond to IP traffic for any IP address assigned to the system.
+  This results in unbalanced receive traffic.
+
+  If you have multiple interfaces in a server, either turn on ARP
+  filtering by
+
+  (1) entering: echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
+      (this only works if your kernel's version is higher than 2.4.5), or
+
+  (2) installing the interfaces in separate broadcast domains (either
+      in different switches or in a switch partitioned to VLANs).
+
+
 Support
 =======
 
@@ -151,20 +183,24 @@ For general information, go to the Intel support website at:
 
     http://support.intel.com
 
+    or the Intel Wired Networking project hosted by Sourceforge at:
+
+    http://sourceforge.net/projects/e1000
+
 If an issue is identified with the released source code on the supported
-kernel with a supported adapter, email the specific information related to 
-the issue to linux.nics@intel.com.
+kernel with a supported adapter, email the specific information related to the
+issue to e1000-devel@lists.sourceforge.net.
 
 
 License
 =======
 
-This software program is released under the terms of a license agreement 
-between you ('Licensee') and Intel. Do not use or load this software or any 
-associated materials (collectively, the 'Software') until you have carefully 
-read the full terms and conditions of the LICENSE located in this software 
-package. By loading or using the Software, you agree to the terms of this 
-Agreement. If you do not agree with the terms of this Agreement, do not 
-install or use the Software.
+This software program is released under the terms of a license agreement
+between you ('Licensee') and Intel. Do not use or load this software or any
+associated materials (collectively, the 'Software') until you have carefully
+read the full terms and conditions of the file COPYING located in this software
+package. By loading or using the Software, you agree to the terms of this
+Agreement. If you do not agree with the terms of this Agreement, do not install
+or use the Software.
 
 * Other names and brands may be claimed as the property of others.
diff --git a/Documentation/networking/e1000.txt b/Documentation/networking/e1000.txt
index 2ebd4058d46d..71fe15af356c 100644
--- a/Documentation/networking/e1000.txt
+++ b/Documentation/networking/e1000.txt
@@ -1,7 +1,7 @@
 Linux* Base Driver for the Intel(R) PRO/1000 Family of Adapters
 ===============================================================
 
-November 17, 2004
+November 15, 2005
 
 
 Contents
@@ -20,254 +20,316 @@ In This Release
 ===============
 
 This file describes the Linux* Base Driver for the Intel(R) PRO/1000 Family
-of Adapters, version 5.x.x.  
+of Adapters.  This driver includes support for Itanium(R)2-based systems.
 
-For questions related to hardware requirements, refer to the documentation 
-supplied with your Intel PRO/1000 adapter. All hardware requirements listed 
+For questions related to hardware requirements, refer to the documentation
+supplied with your Intel PRO/1000 adapter. All hardware requirements listed
 apply to use with Linux.
 
-Native VLANs are now available with supported kernels.
+The following features are now available in supported kernels:
+ - Native VLANs
+ - Channel Bonding (teaming)
+ - SNMP
+
+Channel Bonding documentation can be found in the Linux kernel source:
+/Documentation/networking/bonding.txt
+
+The driver information previously displayed in the /proc filesystem is not
+supported in this release.  Alternatively, you can use ethtool (version 1.6
+or later), lspci, and ifconfig to obtain the same information.
+
+Instructions on updating ethtool can be found in the section "Additional
+Configurations" later in this document.
+
 
 Identifying Your Adapter
 ========================
 
-For more information on how to identify your adapter, go to the Adapter & 
+For more information on how to identify your adapter, go to the Adapter &
 Driver ID Guide at:
 
     http://support.intel.com/support/network/adapter/pro100/21397.htm
 
-For the latest Intel network drivers for Linux, refer to the following 
-website. In the search field, enter your adapter name or type, or use the 
+For the latest Intel network drivers for Linux, refer to the following
+website. In the search field, enter your adapter name or type, or use the
 networking link on the left to search for your adapter:
 
     http://downloadfinder.intel.com/scripts-df/support_intel.asp
 
-Command Line Parameters
-=======================
 
-If the driver is built as a module, the  following optional parameters are 
-used by entering them on the command line with the modprobe or insmod command
-using this syntax:
+Command Line Parameters =======================
+
+If the driver is built as a module, the  following optional parameters
+are used by entering them on the command line with the modprobe or insmod
+command using this syntax:
 
      modprobe e1000 [<option>=<VAL1>,<VAL2>,...]
 
-     insmod e1000 [<option>=<VAL1>,<VAL2>,...] 
+     insmod e1000 [<option>=<VAL1>,<VAL2>,...]
 
 For example, with two PRO/1000 PCI adapters, entering:
 
      insmod e1000 TxDescriptors=80,128
 
-loads the e1000 driver with 80 TX descriptors for the first adapter and 128 TX 
-descriptors for the second adapter.
+loads the e1000 driver with 80 TX descriptors for the first adapter and 128
+TX descriptors for the second adapter.
 
 The default value for each parameter is generally the recommended setting,
-unless otherwise noted. Also, if the driver is statically built into the
-kernel, the driver is loaded with the default values for all the parameters.
-Ethtool can be used to change some of the parameters at runtime.
+unless otherwise noted.
+
+NOTES:  For more information about the AutoNeg, Duplex, and Speed
+        parameters, see the "Speed and Duplex Configuration" section in
+        this document.
 
-    NOTES: For more information about the AutoNeg, Duplex, and Speed
-           parameters, see the "Speed and Duplex Configuration" section in 
-           this document.
+        For more information about the InterruptThrottleRate,
+        RxIntDelay, TxIntDelay, RxAbsIntDelay, and TxAbsIntDelay
+        parameters, see the application note at:
+        http://www.intel.com/design/network/applnots/ap450.htm
 
-           For more information about the InterruptThrottleRate, RxIntDelay, 
-           TxIntDelay, RxAbsIntDelay, and TxAbsIntDelay parameters, see the 
-           application note at:
-           http://www.intel.com/design/network/applnots/ap450.htm
+        A descriptor describes a data buffer and attributes related to
+        the data buffer. This information is accessed by the hardware.
 
-           A descriptor describes a data buffer and attributes related to the 
-           data buffer. This information is accessed by the hardware.
 
-AutoNeg (adapters using copper connections only)
-Valid Range: 0x01-0x0F, 0x20-0x2F
+AutoNeg
+-------
+(Supported only on adapters with copper connections)
+Valid Range:   0x01-0x0F, 0x20-0x2F
 Default Value: 0x2F
-    This parameter is a bit mask that specifies which speed and duplex
-    settings the board advertises. When this parameter is used, the Speed and
-    Duplex parameters must not be specified.
-    NOTE: Refer to the Speed and Duplex section of this readme for more 
-          information on the AutoNeg parameter.  
-
-Duplex (adapters using copper connections only)
-Valid Range: 0-2 (0=auto-negotiate, 1=half, 2=full)
+
+This parameter is a bit mask that specifies which speed and duplex
+settings the board advertises. When this parameter is used, the Speed
+and Duplex parameters must not be specified.
+
+NOTE:  Refer to the Speed and Duplex section of this readme for more
+       information on the AutoNeg parameter.
+
+
+Duplex
+------
+(Supported only on adapters with copper connections)
+Valid Range:   0-2 (0=auto-negotiate, 1=half, 2=full)
 Default Value: 0
-    Defines the direction in which data is allowed to flow. Can be either one 
-    or two-directional. If both Duplex and the link partner are set to auto-
-    negotiate, the board auto-detects the correct duplex. If the link partner
-    is forced (either full or half), Duplex defaults to half-duplex.
+
+Defines the direction in which data is allowed to flow. Can be either
+one or two-directional. If both Duplex and the link partner are set to
+auto-negotiate, the board auto-detects the correct duplex. If the link
+partner is forced (either full or half), Duplex defaults to half-duplex.
+
 
 FlowControl
-Valid Range: 0-3 (0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx)
-Default: Read flow control settings from the EEPROM
-    This parameter controls the automatic generation(Tx) and response(Rx) to 
-    Ethernet PAUSE frames.
+----------
+Valid Range:   0-3 (0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx)
+Default Value: Reads flow control settings from the EEPROM
+
+This parameter controls the automatic generation(Tx) and response(Rx)
+to Ethernet PAUSE frames.
+
 
 InterruptThrottleRate
-Valid Range: 100-100000 (0=off, 1=dynamic)
+---------------------
+(not supported on Intel 82542, 82543 or 82544-based adapters)
+Valid Range:   100-100000 (0=off, 1=dynamic)
 Default Value: 8000
-    This value represents the maximum number of interrupts per second the 
-    controller generates. InterruptThrottleRate is another setting used in 
-    interrupt moderation. Dynamic mode uses a heuristic algorithm to adjust 
-    InterruptThrottleRate based on the current traffic load.
-Un-supported Adapters: InterruptThrottleRate is NOT supported by 82542, 82543
-    or 82544-based adapters.
-
-    NOTE: InterruptThrottleRate takes precedence over the TxAbsIntDelay and 
-          RxAbsIntDelay parameters. In other words, minimizing the receive 
-          and/or transmit absolute delays does not force the controller to 
-          generate more interrupts than what the Interrupt Throttle Rate 
-          allows.
-    CAUTION: If you are using the Intel PRO/1000 CT Network Connection 
-             (controller 82547), setting InterruptThrottleRate to a value 
-             greater than 75,000, may hang (stop transmitting) adapters under 
-             certain network conditions. If this occurs a NETDEV WATCHDOG 
-             message is logged in the system event log. In addition, the 
-             controller is automatically reset, restoring the network 
-             connection. To eliminate the potential for the hang, ensure 
-             that InterruptThrottleRate is set no greater than 75,000 and is 
-             not set to 0.
-    NOTE: When e1000 is loaded with default settings and multiple adapters are 
-          in use simultaneously, the CPU utilization may increase non-linearly. 
-          In order to limit the CPU utilization without impacting the overall 
-          throughput, we recommend that you load the driver as follows:
-
-              insmod e1000.o InterruptThrottleRate=3000,3000,3000
-
-          This sets the InterruptThrottleRate to 3000 interrupts/sec for the 
-          first, second, and third instances of the driver. The range of 2000 to 
-          3000 interrupts per second works on a majority of systems and is a 
-          good starting point, but the optimal value will be platform-specific. 
-          If CPU utilization is not a concern, use RX_POLLING (NAPI) and default 
-          driver settings.
+
+This value represents the maximum number of interrupts per second the
+controller generates. InterruptThrottleRate is another setting used in
+interrupt moderation. Dynamic mode uses a heuristic algorithm to adjust
+InterruptThrottleRate based on the current traffic load.
+
+NOTE:  InterruptThrottleRate takes precedence over the TxAbsIntDelay and
+       RxAbsIntDelay parameters. In other words, minimizing the receive
+       and/or transmit absolute delays does not force the controller to
+       generate more interrupts than what the Interrupt Throttle Rate
+       allows.
+
+CAUTION:  If you are using the Intel PRO/1000 CT Network Connection
+          (controller 82547), setting InterruptThrottleRate to a value
+          greater than 75,000, may hang (stop transmitting) adapters
+          under certain network conditions. If this occurs a NETDEV
+          WATCHDOG message is logged in the system event log. In
+          addition, the controller is automatically reset, restoring
+          the network connection. To eliminate the potential for the
+          hang, ensure that InterruptThrottleRate is set no greater
+          than 75,000 and is not set to 0.
+
+NOTE:  When e1000 is loaded with default settings and multiple adapters
+       are in use simultaneously, the CPU utilization may increase non-
+       linearly. In order to limit the CPU utilization without impacting
+       the overall throughput, we recommend that you load the driver as
+       follows:
+
+           insmod e1000.o InterruptThrottleRate=3000,3000,3000
+
+       This sets the InterruptThrottleRate to 3000 interrupts/sec for
+       the first, second, and third instances of the driver. The range
+       of 2000 to 3000 interrupts per second works on a majority of
+       systems and is a good starting point, but the optimal value will
+       be platform-specific. If CPU utilization is not a concern, use
+       RX_POLLING (NAPI) and default driver settings.
+
 
 RxDescriptors
-Valid Range: 80-256 for 82542 and 82543-based adapters
-             80-4096 for all other supported adapters
+-------------
+Valid Range:   80-256 for 82542 and 82543-based adapters
+               80-4096 for all other supported adapters
 Default Value: 256
-    This value is the number of receive descriptors allocated by the driver. 
-    Increasing this value allows the driver to buffer more incoming packets. 
-    Each descriptor is 16 bytes.  A receive buffer is allocated for each
-    descriptor and can either be 2048 or 4096 bytes long, depending on the MTU 
 
-    setting. An incoming packet can span one or more receive descriptors. 
-    The maximum MTU size is 16110.
+This value specifies the number of receive descriptors allocated by the
+driver. Increasing this value allows the driver to buffer more incoming
+packets.  Each descriptor is 16 bytes.  A receive buffer is also
+allocated for each descriptor and is 2048.
 
-    NOTE: MTU designates the frame size. It only needs to be set for Jumbo 
-          Frames.
-    NOTE: Depending on the available system resources, the request for a
-    higher number of receive descriptors may be denied.  In this case,
-    use a lower number.
 
 RxIntDelay
-Valid Range: 0-65535 (0=off)
+----------
+Valid Range:   0-65535 (0=off)
 Default Value: 0
-    This value delays the generation of receive interrupts in units of 1.024 
-    microseconds.  Receive interrupt reduction can improve CPU efficiency if 
-    properly tuned for specific network traffic. Increasing this value adds 
-    extra latency to frame reception and can end up decreasing the throughput 
-    of TCP traffic. If the system is reporting dropped receives, this value 
-    may be set too high, causing the driver to run out of available receive 
-    descriptors.
-
-    CAUTION: When setting RxIntDelay to a value other than 0, adapters may 
-             hang (stop transmitting) under certain network conditions. If 
-             this occurs a NETDEV WATCHDOG message is logged in the system
-             event log. In addition, the controller is automatically reset, 
-             restoring the network connection. To eliminate the potential for
-             the hang ensure that RxIntDelay is set to 0.
-
-RxAbsIntDelay (82540, 82545 and later adapters only)
-Valid Range: 0-65535 (0=off)
+
+This value delays the generation of receive interrupts in units of 1.024
+microseconds.  Receive interrupt reduction can improve CPU efficiency if
+properly tuned for specific network traffic. Increasing this value adds
+extra latency to frame reception and can end up decreasing the throughput
+of TCP traffic. If the system is reporting dropped receives, this value
+may be set too high, causing the driver to run out of available receive
+descriptors.
+
+CAUTION:  When setting RxIntDelay to a value other than 0, adapters may
+          hang (stop transmitting) under certain network conditions. If
+          this occurs a NETDEV WATCHDOG message is logged in the system
+          event log. In addition, the controller is automatically reset,
+          restoring the network connection. To eliminate the potential
+          for the hang ensure that RxIntDelay is set to 0.
+
+
+RxAbsIntDelay
+-------------
+(This parameter is supported only on 82540, 82545 and later adapters.)
+Valid Range:   0-65535 (0=off)
 Default Value: 128
-    This value, in units of 1.024 microseconds, limits the delay in which a 
-    receive interrupt is generated. Useful only if RxIntDelay is non-zero, 
-    this value ensures that an interrupt is generated after the initial 
-    packet is received within the set amount of time.  Proper tuning,
-    along with RxIntDelay, may improve traffic throughput in specific network
-    conditions.
-
-Speed (adapters using copper connections only)
+
+This value, in units of 1.024 microseconds, limits the delay in which a
+receive interrupt is generated. Useful only if RxIntDelay is non-zero,
+this value ensures that an interrupt is generated after the initial
+packet is received within the set amount of time.  Proper tuning,
+along with RxIntDelay, may improve traffic throughput in specific network
+conditions.
+
+
+Speed
+-----
+(This parameter is supported only on adapters with copper connections.)
 Valid Settings: 0, 10, 100, 1000
-Default Value: 0 (auto-negotiate at all supported speeds)
-    Speed forces the line speed to the specified value in megabits per second
-    (Mbps). If this parameter is not specified or is set to 0 and the link 
-    partner is set to auto-negotiate, the board will auto-detect the correct 
-    speed. Duplex should also be set when Speed is set to either 10 or 100.
+Default Value:  0 (auto-negotiate at all supported speeds)
+
+Speed forces the line speed to the specified value in megabits per second
+(Mbps). If this parameter is not specified or is set to 0 and the link
+partner is set to auto-negotiate, the board will auto-detect the correct
+speed. Duplex should also be set when Speed is set to either 10 or 100.
+
 
 TxDescriptors
-Valid Range: 80-256 for 82542 and 82543-based adapters
-             80-4096 for all other supported adapters
+-------------
+Valid Range:   80-256 for 82542 and 82543-based adapters
+               80-4096 for all other supported adapters
 Default Value: 256
-    This value is the number of transmit descriptors allocated by the driver.
-    Increasing this value allows the driver to queue more transmits. Each 
-    descriptor is 16 bytes.
 
-    NOTE: Depending on the available system resources, the request for a
-    higher number of transmit descriptors may be denied.  In this case,
-    use a lower number.
+This value is the number of transmit descriptors allocated by the driver.
+Increasing this value allows the driver to queue more transmits. Each
+descriptor is 16 bytes.
+
+NOTE:  Depending on the available system resources, the request for a
+       higher number of transmit descriptors may be denied.  In this case,
+       use a lower number.
+
 
 TxIntDelay
-Valid Range: 0-65535 (0=off)
+----------
+Valid Range:   0-65535 (0=off)
 Default Value: 64
-    This value delays the generation of transmit interrupts in units of 
-    1.024 microseconds. Transmit interrupt reduction can improve CPU
-    efficiency if properly tuned for specific network traffic. If the
-    system is reporting dropped transmits, this value may be set too high
-    causing the driver to run out of available transmit descriptors.
-
-TxAbsIntDelay (82540, 82545 and later adapters only)
-Valid Range: 0-65535 (0=off)
+
+This value delays the generation of transmit interrupts in units of
+1.024 microseconds. Transmit interrupt reduction can improve CPU
+efficiency if properly tuned for specific network traffic. If the
+system is reporting dropped transmits, this value may be set too high
+causing the driver to run out of available transmit descriptors.
+
+
+TxAbsIntDelay
+-------------
+(This parameter is supported only on 82540, 82545 and later adapters.)
+Valid Range:   0-65535 (0=off)
 Default Value: 64
-    This value, in units of 1.024 microseconds, limits the delay in which a 
-    transmit interrupt is generated. Useful only if TxIntDelay is non-zero, 
-    this value ensures that an interrupt is generated after the initial 
-    packet is sent on the wire within the set amount of time.  Proper tuning,
-    along with TxIntDelay, may improve traffic throughput in specific 
-    network conditions.
-
-XsumRX (not available on the 82542-based adapter)
-Valid Range: 0-1
+
+This value, in units of 1.024 microseconds, limits the delay in which a
+transmit interrupt is generated. Useful only if TxIntDelay is non-zero,
+this value ensures that an interrupt is generated after the initial
+packet is sent on the wire within the set amount of time.  Proper tuning,
+along with TxIntDelay, may improve traffic throughput in specific
+network conditions.
+
+XsumRX
+------
+(This parameter is NOT supported on the 82542-based adapter.)
+Valid Range:   0-1
 Default Value: 1
-    A value of '1' indicates that the driver should enable IP checksum
-    offload for received packets (both UDP and TCP) to the adapter hardware.
+
+A value of '1' indicates that the driver should enable IP checksum
+offload for received packets (both UDP and TCP) to the adapter hardware.
+
 
 Speed and Duplex Configuration
 ==============================
 
-Three keywords are used to control the speed and duplex configuration. These 
-keywords are Speed, Duplex, and AutoNeg.
+Three keywords are used to control the speed and duplex configuration.
+These keywords are Speed, Duplex, and AutoNeg.
 
-If the board uses a fiber interface, these keywords are ignored, and the 
+If the board uses a fiber interface, these keywords are ignored, and the
 fiber interface board only links at 1000 Mbps full-duplex.
 
 For copper-based boards, the keywords interact as follows:
 
-  The default operation is auto-negotiate. The board advertises all supported
-  speed and duplex combinations, and it links at the highest common speed and
-  duplex mode IF the link partner is set to auto-negotiate.
+  The default operation is auto-negotiate. The board advertises all
+  supported speed and duplex combinations, and it links at the highest
+  common speed and duplex mode IF the link partner is set to auto-negotiate.
 
-  If Speed = 1000, limited auto-negotiation is enabled and only 1000 Mbps is
-  advertised (The 1000BaseT spec requires auto-negotiation.)
+  If Speed = 1000, limited auto-negotiation is enabled and only 1000 Mbps
+  is advertised (The 1000BaseT spec requires auto-negotiation.)
 
   If Speed = 10 or 100, then both Speed and Duplex should be set. Auto-
-  negotiation is disabled, and the AutoNeg parameter is ignored. Partner SHOULD
-  also be forced.
+  negotiation is disabled, and the AutoNeg parameter is ignored. Partner
+  SHOULD also be forced.
+
+The AutoNeg parameter is used when more control is required over the
+auto-negotiation process.  It should be used when you wish to control which
+speed and duplex combinations are advertised during the auto-negotiation
+process.
+
+The parameter may be specified as either a decimal or hexidecimal value as
+determined by the bitmap below.
 
-The AutoNeg parameter is used when more control is required over the auto-
-negotiation process. When this parameter is used, Speed and Duplex parameters 
-must not be specified. The following table describes supported values for the 
-AutoNeg parameter:
+Bit position   7      6      5       4       3      2      1       0
+Decimal Value  128    64     32      16      8      4      2       1
+Hex value      80     40     20      10      8      4      2       1
+Speed (Mbps)   N/A    N/A    1000    N/A     100    100    10      10
+Duplex                       Full            Full   Half   Full    Half
 
-Speed (Mbps)             1000      100    100    10     10
-Duplex                   Full      Full   Half   Full   Half
-Value (in base 16)       0x20      0x08   0x04   0x02   0x01
+Some examples of using AutoNeg:
 
-Example: insmod e1000 AutoNeg=0x03, loads e1000 and specifies (10 full duplex, 
-10 half duplex) for negotiation with the peer.
+  modprobe e1000 AutoNeg=0x01 (Restricts autonegotiation to 10 Half)
+  modprobe e1000 AutoNeg=1 (Same as above)
+  modprobe e1000 AutoNeg=0x02 (Restricts autonegotiation to 10 Full)
+  modprobe e1000 AutoNeg=0x03 (Restricts autonegotiation to 10 Half or 10 Full)
+  modprobe e1000 AutoNeg=0x04 (Restricts autonegotiation to 100 Half)
+  modprobe e1000 AutoNeg=0x05 (Restricts autonegotiation to 10 Half or 100
+  Half)
+  modprobe e1000 AutoNeg=0x020 (Restricts autonegotiation to 1000 Full)
+  modprobe e1000 AutoNeg=32 (Same as above)
 
-Note that setting AutoNeg does not guarantee that the board will link at the 
-highest specified speed or duplex mode, but the board will link at the 
-highest possible speed/duplex of the link partner IF the link partner is also
-set to auto-negotiate. If the link partner is forced speed/duplex, the 
-adapter MUST be forced to the same speed/duplex.
+Note that when this parameter is used, Speed and Duplex must not be specified.
+
+If the link partner is forced to a specific speed and duplex, then this
+parameter should not be used.  Instead, use the Speed and Duplex parameters
+previously mentioned to force the adapter to the same speed and duplex.
 
 
 Additional Configurations
@@ -276,19 +338,19 @@ Additional Configurations
   Configuring the Driver on Different Distributions
   -------------------------------------------------
 
-  Configuring a network driver to load properly when the system is started is
-  distribution dependent. Typically, the configuration process involves adding
-  an alias line to /etc/modules.conf as well as editing other system startup 
-  scripts and/or configuration files. Many popular Linux distributions ship 
-  with tools to make these changes for you. To learn the proper way to 
-  configure a network device for your system, refer to your distribution 
-  documentation. If during this process you are asked for the driver or module 
-  name, the name for the Linux Base Driver for the Intel PRO/1000 Family of 
-  Adapters is e1000.
+  Configuring a network driver to load properly when the system is started
+  is distribution dependent. Typically, the configuration process involves
+  adding an alias line to /etc/modules.conf or /etc/modprobe.conf as well
+  as editing other system startup scripts and/or configuration files. Many
+  popular Linux distributions ship with tools to make these changes for you.
+  To learn the proper way to configure a network device for your system,
+  refer to your distribution documentation. If during this process you are
+  asked for the driver or module name, the name for the Linux Base Driver
+  for the Intel PRO/1000 Family of Adapters is e1000.
 
-  As an example, if you install the e1000 driver for two PRO/1000 adapters 
-  (eth0 and eth1) and set the speed and duplex to 10full and 100half, add the 
-  following to modules.conf:
+  As an example, if you install the e1000 driver for two PRO/1000 adapters
+  (eth0 and eth1) and set the speed and duplex to 10full and 100half, add
+  the following to modules.conf or or modprobe.conf:
 
        alias eth0 e1000
        alias eth1 e1000
@@ -297,9 +359,9 @@ Additional Configurations
   Viewing Link Messages
   ---------------------
 
-  Link messages will not be displayed to the console if the distribution is 
-  restricting system messages. In order to see network driver link messages on 
-  your console, set dmesg to eight by entering the following:
+  Link messages will not be displayed to the console if the distribution is
+  restricting system messages. In order to see network driver link messages
+  on your console, set dmesg to eight by entering the following:
 
        dmesg -n 8
 
@@ -308,22 +370,42 @@ Additional Configurations
   Jumbo Frames
   ------------
 
-  The driver supports Jumbo Frames for all adapters except 82542-based 
-  adapters. Jumbo Frames support is enabled by changing the MTU to a value 
-  larger than the default of 1500. Use the ifconfig command to increase the 
-  MTU size. For example:
+  The driver supports Jumbo Frames for all adapters except 82542 and
+  82573-based adapters. Jumbo Frames support is enabled by changing the
+  MTU to a value larger than the default of 1500. Use the ifconfig command
+  to increase the MTU size. For example:
+
+       ifconfig eth<x> mtu 9000 up
+
+  This setting is not saved across reboots.  It can be made permanent if
+  you add:
+
+       MTU=9000
 
-        ifconfig ethx mtu 9000 up
+   to the file /etc/sysconfig/network-scripts/ifcfg-eth<x>.  This example
+   applies to the Red Hat distributions; other distributions may store this
+   setting in a different location.
 
-  The maximum MTU setting for Jumbo Frames is 16110. This value coincides 
-  with the maximum Jumbo Frames size of 16128.
+  Notes:
 
-  NOTE: Jumbo Frames are supported at 1000 Mbps only. Using Jumbo Frames at 
-  10 or 100 Mbps may result in poor performance or loss of link.
+  - To enable Jumbo Frames, increase the MTU size on the interface beyond
+    1500.
+  - The maximum MTU setting for Jumbo Frames is 16110. This value coincides
+    with the maximum Jumbo Frames size of 16128.
+  - Using Jumbo Frames at 10 or 100 Mbps may result in poor performance or
+    loss of link.
+  - Some Intel gigabit adapters that support Jumbo Frames have a frame size
+    limit of 9238 bytes, with a corresponding MTU size limit of 9216 bytes.
+    The adapters with this limitation are based on the Intel 82571EB and
+    82572EI controllers, which correspond to these product names:
+     Intel® PRO/1000 PT Dual Port Server Adapter
+     Intel® PRO/1000 PF Dual Port Server Adapter
+     Intel® PRO/1000 PT Server Adapter
+     Intel® PRO/1000 PT Desktop Adapter
+     Intel® PRO/1000 PF Server Adapter
 
+  - The Intel PRO/1000 PM Network Connection does not support jumbo frames.
 
-  NOTE: MTU designates the frame size. To enable Jumbo Frames, increase the
-  MTU size on the interface beyond 1500.
 
   Ethtool
   -------
@@ -333,32 +415,41 @@ Additional Configurations
   version 1.6 or later is required for this functionality.
 
   The latest release of ethtool can be found from
-  http://sf.net/projects/gkernel.  
+  http://sourceforge.net/projects/gkernel.
 
-  NOTE: Ethtool 1.6 only supports a limited set of ethtool options. Support 
-  for a more complete ethtool feature set can be enabled by upgrading 
-  ethtool to ethtool-1.8.1. 
+  NOTE: Ethtool 1.6 only supports a limited set of ethtool options. Support
+  for a more complete ethtool feature set can be enabled by upgrading
+  ethtool to ethtool-1.8.1.
 
   Enabling Wake on LAN* (WoL)
   ---------------------------
 
   WoL is configured through the Ethtool* utility. Ethtool is included with
-  all versions of Red Hat after Red Hat 7.2. For other Linux distributions, 
-  download and install Ethtool from the following website: 
+  all versions of Red Hat after Red Hat 7.2. For other Linux distributions,
+  download and install Ethtool from the following website:
   http://sourceforge.net/projects/gkernel.
 
-  For instructions on enabling WoL with Ethtool, refer to the website listed 
+  For instructions on enabling WoL with Ethtool, refer to the website listed
   above.
 
-  WoL will be enabled on the system during the next shut down or reboot. 
-  For this driver version, in order to enable WoL, the e1000 driver must be 
+  WoL will be enabled on the system during the next shut down or reboot.
+  For this driver version, in order to enable WoL, the e1000 driver must be
   loaded when shutting down or rebooting the system.
 
   NAPI
   ----
 
   NAPI (Rx polling mode) is supported in the e1000 driver. NAPI is enabled
-  or disabled based on the configuration of the kernel. 
+  or disabled based on the configuration of the kernel. To override
+  the default, use the following compile-time flags.
+
+  To enable NAPI, compile the driver module, passing in a configuration option:
+
+       make CFLAGS_EXTRA=-DE1000_NAPI install
+
+  To disable NAPI, compile the driver module, passing in a configuration option:
+
+       make CFLAGS_EXTRA=-DE1000_NO_NAPI install
 
   See www.cyberus.ca/~hadi/usenix-paper.tgz for more information on NAPI.
 
@@ -369,10 +460,85 @@ Known Issues
   Jumbo Frames System Requirement
   -------------------------------
 
-  Memory allocation failures have been observed on Linux systems with 64 MB 
-  of RAM or less that are running Jumbo Frames. If you are using Jumbo Frames,
-  your system may require more than the advertised minimum requirement of 64 MB
-  of system memory.
+  Memory allocation failures have been observed on Linux systems with 64 MB
+  of RAM or less that are running Jumbo Frames. If you are using Jumbo
+  Frames, your system may require more than the advertised minimum
+  requirement of 64 MB of system memory.
+
+  Performance Degradation with Jumbo Frames
+  -----------------------------------------
+
+  Degradation in throughput performance may be observed in some Jumbo frames
+  environments. If this is observed, increasing the application's socket
+  buffer size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values
+  may help. See the specific application manual and
+  /usr/src/linux*/Documentation/
+  networking/ip-sysctl.txt for more details.
+
+  Jumbo frames on Foundry BigIron 8000 switch
+  -------------------------------------------
+  There is a known issue using Jumbo frames when connected to a Foundry
+  BigIron 8000 switch. This is a 3rd party limitation. If you experience
+  loss of packets, lower the MTU size.
+
+  Multiple Interfaces on Same Ethernet Broadcast Network
+  ------------------------------------------------------
+
+  Due to the default ARP behavior on Linux, it is not possible to have
+  one system on two IP networks in the same Ethernet broadcast domain
+  (non-partitioned switch) behave as expected. All Ethernet interfaces
+  will respond to IP traffic for any IP address assigned to the system.
+  This results in unbalanced receive traffic.
+
+  If you have multiple interfaces in a server, either turn on ARP
+  filtering by entering:
+
+      echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
+  (this only works if your kernel's version is higher than 2.4.5),
+
+  NOTE: This setting is not saved across reboots. The configuration
+  change can be made permanent by adding the line:
+      net.ipv4.conf.all.arp_filter = 1
+  to the file /etc/sysctl.conf
+
+        or,
+
+  install the interfaces in separate broadcast domains (either in
+  different switches or in a switch partitioned to VLANs).
+
+  82541/82547 can't link or are slow to link with some link partners
+  -----------------------------------------------------------------
+
+  There is a known compatibility issue with 82541/82547 and some
+  low-end switches where the link will not be established, or will
+  be slow to establish.  In particular, these switches are known to
+  be incompatible with 82541/82547:
+
+      Planex FXG-08TE
+      I-O Data ETG-SH8
+
+  To workaround this issue, the driver can be compiled with an override
+  of the PHY's master/slave setting.  Forcing master or forcing slave
+  mode will improve time-to-link.
+
+      # make EXTRA_CFLAGS=-DE1000_MASTER_SLAVE=<n>
+
+  Where <n> is:
+
+      0 = Hardware default
+      1 = Master mode
+      2 = Slave mode
+      3 = Auto master/slave
+
+  Disable rx flow control with ethtool
+  ------------------------------------
+
+  In order to disable receive flow control using ethtool, you must turn
+  off auto-negotiation on the same command line.
+
+  For example:
+
+     ethtool -A eth? autoneg off rx off
 
 
 Support
@@ -382,20 +548,24 @@ For general information, go to the Intel support website at:
 
     http://support.intel.com
 
+    or the Intel Wired Networking project hosted by Sourceforge at:
+
+    http://sourceforge.net/projects/e1000
+
 If an issue is identified with the released source code on the supported
-kernel with a supported adapter, email the specific information related to 
-the issue to linux.nics@intel.com.
+kernel with a supported adapter, email the specific information related
+to the issue to e1000-devel@lists.sourceforge.net
 
 
 License
 =======
 
-This software program is released under the terms of a license agreement 
-between you ('Licensee') and Intel. Do not use or load this software or any 
-associated materials (collectively, the 'Software') until you have carefully 
-read the full terms and conditions of the LICENSE located in this software 
-package. By loading or using the Software, you agree to the terms of this 
-Agreement. If you do not agree with the terms of this Agreement, do not 
+This software program is released under the terms of a license agreement
+between you ('Licensee') and Intel. Do not use or load this software or any
+associated materials (collectively, the 'Software') until you have carefully
+read the full terms and conditions of the file COPYING located in this software
+package. By loading or using the Software, you agree to the terms of this
+Agreement. If you do not agree with the terms of this Agreement, do not
 install or use the Software.
 
 * Other names and brands may be claimed as the property of others.
diff --git a/Documentation/sound/alsa/ALSA-Configuration.txt b/Documentation/sound/alsa/ALSA-Configuration.txt
index 36b511c7cade..1def6049784c 100644
--- a/Documentation/sound/alsa/ALSA-Configuration.txt
+++ b/Documentation/sound/alsa/ALSA-Configuration.txt
@@ -513,6 +513,8 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
 
     This module supports multiple cards and autoprobe.
     
+    The power-management is supported.
+
   Module snd-ens1371
   ------------------
 
@@ -526,6 +528,8 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
 
     This module supports multiple cards and autoprobe.
     
+    The power-management is supported.
+
   Module snd-es968
   ----------------
 
@@ -671,6 +675,8 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
 
     model       - force the model name
     position_fix - Fix DMA pointer (0 = auto, 1 = none, 2 = POSBUF, 3 = FIFO size)
+    single_cmd  - Use single immediate commands to communicate with
+                codecs (for debugging only)
 
     This module supports one card and autoprobe.
 
@@ -694,13 +700,34 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
           asus          3-jack
           uniwill       3-jack
           F1734         2-jack
+          lg            LG laptop (m1 express dual)
           test          for testing/debugging purpose, almost all controls can be
                         adjusted.  Appearing only when compiled with
                         $CONFIG_SND_DEBUG=y
+          auto          auto-config reading BIOS (default)
 
         ALC260
           hp            HP machines
           fujitsu       Fujitsu S7020
+          acer          Acer TravelMate
+          basic         fixed pin assignment (old default model)
+          auto          auto-config reading BIOS (default)
+
+        ALC262
+          fujitsu       Fujitsu Laptop
+          basic         fixed pin assignment w/o SPDIF
+          auto          auto-config reading BIOS (default)
+
+        ALC882/883/885
+          3stack-dig    3-jack with SPDIF I/O
+          6stck-dig     6-jack digital with SPDIF I/O
+          auto          auto-config reading BIOS (default)
+
+        ALC861
+          3stack        3-jack
+          3stack-dig    3-jack with SPDIF I/O
+          6stack-dig    6-jack with SPDIF I/O
+          auto          auto-config reading BIOS (default)
 
         CMI9880
           minimal       3-jack in back
@@ -710,6 +737,28 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
           allout        5-jack in back, 2-jack in front, SPDIF out
           auto          auto-config reading BIOS (default)
 
+        AD1981
+          basic         3-jack (default)
+          hp            HP nx6320
+
+        AD1986A
+          6stack        6-jack, separate surrounds (default)
+          3stack        3-stack, shared surrounds
+          laptop        2-channel only (FSC V2060, Samsung M50)
+          laptop-eapd   2-channel with EAPD (Samsung R65, ASUS A6J)
+
+        AD1988
+          6stack        6-jack
+          6stack-dig    ditto with SPDIF
+          3stack        3-jack
+          3stack-dig    ditto with SPDIF
+          laptop        3-jack with hp-jack automute
+          laptop-dig    ditto with SPDIF
+          auto          auto-confgi reading BIOS (default)
+
+        STAC7661(?)
+          vaio          Setup for VAIO FE550G/SZ110
+
     If the default configuration doesn't work and one of the above
     matches with your device, report it together with the PCI
     subsystem ID (output of "lspci -nv") to ALSA BTS or alsa-devel
@@ -723,6 +772,17 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
             (Usually SD_LPLIB register is more accurate than the
             position buffer.)
 
+    NB: If you get many "azx_get_response timeout" messages at
+    loading, it's likely a problem of interrupts (e.g. ACPI irq
+    routing).  Try to boot with options like "pci=noacpi".  Also, you
+    can try "single_cmd=1" module option.  This will switch the
+    communication method between HDA controller and codecs to the
+    single immediate commands instead of CORB/RIRB.  Basically, the
+    single command mode is provided only for BIOS, and you won't get
+    unsolicited events, too.  But, at least, this works independently
+    from the irq.  Remember this is a last resort, and should be
+    avoided as much as possible...
+    
     The power-management is supported.
 
   Module snd-hdsp
@@ -802,6 +862,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
   ------------------
 
     Module for Envy24HT (VT/ICE1724), Envy24PT (VT1720) based PCI sound cards.
+                        * MidiMan M Audio Revolution 5.1
                         * MidiMan M Audio Revolution 7.1
                         * AMP Ltd AUDIO2000
                         * TerraTec Aureon 5.1 Sky
@@ -810,6 +871,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
                         * TerraTec Phase 22
                         * TerraTec Phase 28
                         * AudioTrak Prodigy 7.1
+                        * AudioTrak Prodigy 7.1LT
                         * AudioTrak Prodigy 192
                         * Pontis MS300
                         * Albatron K8X800 Pro II 
@@ -820,9 +882,9 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
                         * Shuttle SN25P
 
     model       - Use the given board model, one of the following:
-                  revo71, amp2000, prodigy71, prodigy192, aureon51,
-                  aureon71, universe, k8x800, phase22, phase28, ms300,
-                  av710
+                  revo51, revo71, amp2000, prodigy71, prodigy71lt,
+                  prodigy192, aureon51, aureon71, universe,
+                  k8x800, phase22, phase28, ms300, av710
 
     This module supports multiple cards and autoprobe.
 
@@ -1353,6 +1415,9 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
 
     vid             - Vendor ID for the device (optional)
     pid             - Product ID for the device (optional)
+    device_setup    - Device specific magic number (optional)
+                    - Influence depends on the device
+                    - Default: 0x0000 
 
     This module supports multiple devices, autoprobe and hotplugging.
 
diff --git a/Documentation/sound/alsa/Audiophile-Usb.txt b/Documentation/sound/alsa/Audiophile-Usb.txt
new file mode 100644
index 000000000000..4692c8e77dc1
--- /dev/null
+++ b/Documentation/sound/alsa/Audiophile-Usb.txt
@@ -0,0 +1,333 @@
+        Guide to using M-Audio Audiophile USB with ALSA and Jack        v1.2
+        ========================================================
+
+            Thibault Le Meur <Thibault.LeMeur@supelec.fr>
+
+This document is a guide to using the M-Audio Audiophile USB (tm) device with 
+ALSA and JACK.
+
+1 - Audiophile USB Specs and correct usage
+==========================================
+This part is a reminder of important facts about the functions and limitations 
+of the device.
+
+The device has 4 audio interfaces, and 2 MIDI ports:
+ * Analog Stereo Input (Ai)
+   - This port supports 2 pairs of line-level audio inputs (1/4" TS and RCA) 
+   - When the 1/4" TS (jack) connectors are connected, the RCA connectors
+     are disabled
+ * Analog Stereo Output (Ao)
+ * Digital Stereo Input (Di)
+ * Digital Stereo Output (Do)
+ * Midi In (Mi)
+ * Midi Out (Mo)
+
+The internal DAC/ADC has the following caracteristics:
+* sample depth of 16 or 24 bits
+* sample rate from 8kHz to 96kHz
+* Two ports can't use different sample depths at the same time.Moreover, the 
+Audiophile USB documentation gives the following Warning: "Please exit any 
+audio application running before switching between bit depths"
+
+Due to the USB 1.1 bandwidth limitation, a limited number of interfaces can be 
+activated at the same time depending on the audio mode selected:
+ * 16-bit/48kHz ==> 4 channels in/ 4 channels out
+   - Ai+Ao+Di+Do
+ * 24-bit/48kHz ==> 4 channels in/2 channels out, 
+                    or 2 channels in/4 channels out
+   - Ai+Ao+Do or Ai+Di+Ao or Ai+Di+Do or Di+Ao+Do
+ * 24-bit/96kHz ==> 2 channels in, or 2 channels out (half duplex only)
+   - Ai or Ao or Di or Do
+
+Important facts about the Digital interface:
+--------------------------------------------
+ * The Do port additionnaly supports surround-encoded AC-3 and DTS passthrough, 
+though I haven't tested it under linux
+   - Note that in this setup only the Do interface can be enabled
+ * Apart from recording an audio digital stream, enabling the Di port is a way 
+to synchronize the device to an external sample clock
+   - As a consequence, the Di port must be enable only if an active Digital 
+source is connected
+   - Enabling Di when no digital source is connected can result in a 
+synchronization error (for instance sound played at an odd sample rate)
+
+
+2 - Audiophile USB support in ALSA
+==================================
+
+2.1 - MIDI ports
+----------------
+The Audiophile USB MIDI ports will be automatically supported once the 
+following modules have been loaded:
+ * snd-usb-audio
+ * snd-seq
+ * snd-seq-midi
+
+No additionnal setting is required.
+
+2.2 - Audio ports
+-----------------
+
+Audio functions of the Audiophile USB device are handled by the snd-usb-audio 
+module. This module can work in a default mode (without any device-specific 
+parameter), or in an advanced mode with the device-specific parameter called 
+"device_setup".
+
+2.2.1 - Default Alsa driver mode
+
+The default behaviour of the snd-usb-audio driver is to parse the device 
+capabilities at startup and enable all functions inside the device (including 
+all ports at any sample rates and any sample depths supported). This approach 
+has the advantage to let the driver easily switch from sample rates/depths 
+automatically according to the need of the application claiming the device.
+
+In this case the Audiophile ports are mapped to alsa pcm devices in the 
+following way (I suppose the device's index is 1):
+ * hw:1,0 is Ao in playback and Di in capture
+ * hw:1,1 is Do in playback and Ai in capture
+ * hw:1,2 is Do in AC3/DTS passthrough mode
+
+You must note as well that the device uses Big Endian byte encoding so that 
+supported audio format are S16_BE  for 16-bit depth modes and S24_3BE for 
+24-bits depth mode. One exception is the hw:1,2 port which is Little Endian 
+compliant and thus uses S16_LE.
+
+Examples:
+ * playing a S24_3BE encoded raw file to the Ao port
+   % aplay -D hw:1,0 -c2 -t raw -r48000 -fS24_3BE test.raw
+ * recording a  S24_3BE encoded raw file from the Ai port
+   % arecord -D hw:1,1 -c2  -t raw -r48000 -fS24_3BE test.raw
+ * playing a S16_BE encoded raw file to the Do port
+   % aplay -D hw:1,1 -c2 -t raw -r48000 -fS16_BE test.raw
+
+If you're happy with the default Alsa driver setup and don't experience any 
+issue with this mode, then you can skip the following chapter.
+
+2.2.2 - Advanced module setup
+
+Due to the hardware constraints described above, the device initialization made 
+by the Alsa driver in default mode may result in a corrupted state of the 
+device. For instance, a particularly annoying issue is that the sound captured 
+from the Ai port sounds distorted (as if boosted with an excessive high volume 
+gain).
+
+For people having this problem, the snd-usb-audio module has a new module 
+parameter called "device_setup".
+
+2.2.2.1 - Initializing the working mode of the Audiohile USB
+
+As far as the Audiohile USB device is concerned, this value let the user 
+specify:
+ * the sample depth
+ * the sample rate
+ * whether the Di port is used or not 
+
+Here is a list of supported device_setup values for this device:
+ * device_setup=0x00 (or omitted)
+   - Alsa driver default mode
+   - maintains backward compatibility with setups that do not use this 
+     parameter by not introducing any change
+   - results sometimes in corrupted sound as decribed earlier
+ * device_setup=0x01
+   - 16bits 48kHz mode with Di disabled
+   - Ai,Ao,Do can be used at the same time
+   - hw:1,0 is not available in capture mode
+   - hw:1,2 is not available
+ * device_setup=0x11
+   - 16bits 48kHz mode with Di enabled
+   - Ai,Ao,Di,Do can be used at the same time
+   - hw:1,0 is available in capture mode
+   - hw:1,2 is not available
+ * device_setup=0x09
+   - 24bits 48kHz mode with Di disabled
+   - Ai,Ao,Do can be used at the same time
+   - hw:1,0 is not available in capture mode
+   - hw:1,2 is not available
+ * device_setup=0x19
+   - 24bits 48kHz mode with Di enabled
+   - 3 ports from {Ai,Ao,Di,Do} can be used at the same time
+   - hw:1,0 is available in capture mode and an active digital source must be 
+     connected to Di
+   - hw:1,2 is not available
+ * device_setup=0x0D or 0x10
+   - 24bits 96kHz mode
+   - Di is enabled by default for this mode but does not need to be connected 
+     to an active source
+   - Only 1 port from {Ai,Ao,Di,Do} can be used at the same time
+   - hw:1,0 is available in captured mode
+   - hw:1,2 is not available
+ * device_setup=0x03
+   - 16bits 48kHz mode with only the Do port enabled 
+   - AC3 with DTS passthru (not tested)
+   - Caution with this setup the Do port is mapped to the pcm device hw:1,0
+
+2.2.2.2 - Setting and switching configurations with the device_setup parameter
+
+The parameter can be given:
+ * By manually probing the device (as root):
+   # modprobe -r snd-usb-audio
+   # modprobe snd-usb-audio index=1 device_setup=0x09
+ * Or while configuring the modules options in your modules configuration file
+   - For Fedora distributions, edit the /etc/modprobe.conf file:
+       alias snd-card-1 snd-usb-audio
+       options snd-usb-audio index=1 device_setup=0x09
+
+IMPORTANT NOTE WHEN SWITCHING CONFIGURATION:
+-------------------------------------------
+ * You may need to _first_ intialize the module with the correct device_setup 
+   parameter and _only_after_ turn on the Audiophile USB device
+ * This is especially true when switching the sample depth:
+   - first trun off the device
+   - de-register the snd-usb-audio module
+   - change the device_setup parameter (by either manually reprobing the module 
+     or changing modprobe.conf)
+   - turn on the device
+
+2.2.2.3 - Audiophile USB's device_setup structure
+
+If you want to understand the device_setup magic numbers for the Audiophile 
+USB, you need some very basic understanding of binary computation. However, 
+this is not required to use the parameter and you may skip thi section.
+
+The device_setup is one byte long and its structure is the following:
+
+       +---+---+---+---+---+---+---+---+
+       | b7| b6| b5| b4| b3| b2| b1| b0|
+       +---+---+---+---+---+---+---+---+
+       | 0 | 0 | 0 | Di|24B|96K|DTS|SET|
+       +---+---+---+---+---+---+---+---+
+
+Where:
+ * b0 is the "SET" bit
+   - it MUST be set if device_setup is initialized 
+ * b1 is the "DTS" bit
+   - it is set only for Digital output with DTS/AC3
+   - this setup is not tested
+ * b2 is the Rate selection flag
+   - When set to "1" the rate range is 48.1-96kHz
+   - Otherwise the sample rate range is 8-48kHz
+ * b3 is the bit depth selection flag
+   - When set to "1" samples are 24bits long
+   - Otherwise they are 16bits long
+   - Note that b2 implies b3 as the 96kHz mode is only supported for 24 bits 
+     samples
+ * b4 is the Digital input flag
+   - When set to "1" the device assumes that an active digital source is 
+     connected 
+   - You shouldn't enable Di if no source is seen on the port (this leads to 
+     synchronization issues)
+   - b4 is implied by b2 (since only one port is enabled at a time no synch 
+     error can occur) 
+ * b5 to b7 are reserved for future uses, and must be set to "0"
+   - might become Ao, Do, Ai, for b7, b6, b4 respectively
+
+Caution:
+ * there is no check on the value you will give to device_setup
+   - for instance choosing 0x05 (16bits 96kHz) will fail back to 0x09 since 
+     b2 implies b3. But _there_will_be_no_warning_ in /var/log/messages
+ * Hardware constraints due to the USB bus limitation aren't checked
+   - choosing b2 will prepare all interfaces for 24bits/96kHz but you'll
+     only be able to use one at the same time
+
+2.2.3 -  USB implementation details for this device
+
+You may safely skip this section if you're not interrested in driver 
+development.
+
+This section describes some internals aspect of the device and summarize the 
+data I got by usb-snooping the windows and linux drivers.
+
+The M-Audio Audiophile USB has 7 USB Interfaces:
+a "USB interface":
+ * USB Interface nb.0
+ * USB Interface nb.1
+   - Audio Control function
+ * USB Interface nb.2
+   - Analog Output
+ * USB Interface nb.3
+   - Digital Output
+ * USB Interface nb.4
+   - Analog Input
+ * USB Interface nb.5
+   - Digital Input
+ * USB Interface nb.6
+   - MIDI interface compliant with the MIDIMAN quirk 
+
+Each interface has 5 altsettings (AltSet 1,2,3,4,5) except:
+ * Interface 3 (Digital Out) has an extra Alset nb.6 
+ * Interface 5 (Digital In) does not have Alset nb.3 and 5 
+
+Here is a short description of the AltSettings capabilities:
+ * AltSettings 1 corresponds to
+  - 24-bit depth, 48.1-96kHz sample mode
+  - Adaptive playback (Ao and Do), Synch capture (Ai), or Asynch capture (Di)
+ * AltSettings 2 corresponds to
+  - 24-bit depth, 8-48kHz sample mode
+  - Asynch capture and playback  (Ao,Ai,Do,Di)
+ * AltSettings 3 corresponds to
+  - 24-bit depth, 8-48kHz sample mode
+  - Synch capture (Ai) and Adaptive playback (Ao,Do)
+ * AltSettings 4 corresponds to
+  - 16-bit depth, 8-48kHz sample mode
+  - Asynch capture and playback  (Ao,Ai,Do,Di)
+ * AltSettings 5 corresponds to
+  - 16-bit depth, 8-48kHz sample mode
+  - Synch capture (Ai) and Adaptive playback (Ao,Do)
+ * AltSettings 6 corresponds to
+  - 16-bit depth, 8-48kHz sample mode
+  - Synch playback (Do), audio format type III IEC1937_AC-3
+
+In order to ensure a correct intialization of the device, the driver 
+_must_know_ how the device will be used:
+ * if DTS is choosen, only Interface 2 with AltSet nb.6 must be
+   registered
+ * if 96KHz only AltSets nb.1 of each interface must be selected
+ * if samples are using 24bits/48KHz then AltSet 2 must me used if
+   Digital input is connected, and only AltSet nb.3 if Digital input
+   is not connected
+ * if samples are using 16bits/48KHz then AltSet 4 must me used if
+   Digital input is connected, and only AltSet nb.5 if Digital input
+   is not connected
+
+When device_setup is given as a parameter to the snd-usb-audio module, the 
+parse_audio_enpoint function uses a quirk called 
+"audiophile_skip_setting_quirk" in order to prevent AltSettings not 
+corresponding to device_setup from being registered in the driver.
+
+3 - Audiophile USB and Jack support
+===================================
+
+This section deals with support of the Audiophile USB device in Jack.
+The main issue regarding this support is that the device is Big Endian 
+compliant.
+
+3.1 - Using the plug alsa plugin
+--------------------------------
+
+Jack doesn't directly support big endian devices. Thus, one way to have support 
+for this device with Alsa is to use the Alsa "plug" converter.
+
+For instance here is one way to run Jack with 2 playback channels on Ao and 2 
+capture channels from Ai:
+  % jackd -R -dalsa -dplughw:1 -r48000 -p256 -n2 -D -Cplughw:1,1
+
+
+However you may see the following warning message:
+"You appear to be using the ALSA software "plug" layer, probably a result of 
+using the "default" ALSA device. This is less efficient than it could be. 
+Consider using a hardware device instead rather than using the plug layer."
+
+
+3.2 - Patching alsa to use direct pcm device
+-------------------------------------------
+A patch for Jack by Andreas Steinmetz adds support for Big Endian devices. 
+However it has not been included in the CVS tree.
+
+You can find it at the following URL:
+http://sourceforge.net/tracker/index.php?func=detail&aid=1289682&group_id=39687&
+atid=425939
+
+After having applied the patch you can run jackd with the following command 
+line:
+  % jackd -R -dalsa -Phw:1,0 -r48000 -p128 -n2 -D -Chw:1,1
+
diff --git a/Documentation/sound/alsa/DocBook/writing-an-alsa-driver.tmpl b/Documentation/sound/alsa/DocBook/writing-an-alsa-driver.tmpl
index 4251085d38d3..6dc9d9f622ca 100644
--- a/Documentation/sound/alsa/DocBook/writing-an-alsa-driver.tmpl
+++ b/Documentation/sound/alsa/DocBook/writing-an-alsa-driver.tmpl
@@ -1834,7 +1834,7 @@
           mychip_set_sample_format(chip, runtime->format);
           mychip_set_sample_rate(chip, runtime->rate);
           mychip_set_channels(chip, runtime->channels);
-          mychip_set_dma_setup(chip, runtime->dma_area,
+          mychip_set_dma_setup(chip, runtime->dma_addr,
                                chip->buffer_size,
                                chip->period_size);
           return 0;
@@ -3388,7 +3388,7 @@ struct _snd_pcm_runtime {
           .name = "PCM Playback Switch",
           .index = 0,
           .access = SNDRV_CTL_ELEM_ACCESS_READWRITE,
-          .private_values = 0xffff,
+          .private_value = 0xffff,
           .info = my_control_info,
           .get = my_control_get,
           .put = my_control_put
@@ -3449,7 +3449,7 @@ struct _snd_pcm_runtime {
       </para>
 
       <para>
-        The <structfield>private_values</structfield> field contains
+        The <structfield>private_value</structfield> field contains
       an arbitrary long integer value for this record. When using
       generic <structfield>info</structfield>,
       <structfield>get</structfield> and
diff --git a/Documentation/spinlocks.txt b/Documentation/spinlocks.txt
index c2122996631e..a661d684768e 100644
--- a/Documentation/spinlocks.txt
+++ b/Documentation/spinlocks.txt
@@ -9,7 +9,7 @@ removed soon. So for any new code dynamic initialization should be used:
    static int __init xxx_init(void)
    {
         spin_lock_init(&xxx_lock);
-        rw_lock_init(&xxx_rw_lock);
+        rwlock_init(&xxx_rw_lock);
         ...
    }