7 files changed, 212 insertions, 10 deletions

diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt
index 2193be53e773..5ddbe350487a 100644
--- a/Documentation/feature-removal-schedule.txt
+++ b/Documentation/feature-removal-schedule.txt
@@ -318,6 +318,14 @@ Who:	Jean Delvare <khali@linux-fr.org>
 
 ---------------------------
 
+What:   fscher and fscpos drivers
+When:   June 2009
+Why:    Deprecated by the new fschmd driver.
+Who:    Hans de Goede <hdegoede@redhat.com>
+        Jean Delvare <khali@linux-fr.org>
+
+---------------------------
+
 What:   SELinux "compat_net" functionality
 When:   2.6.30 at the earliest
 Why:    In 2.6.18 the Secmark concept was introduced to replace the "compat_net"
diff --git a/Documentation/hwmon/f71882fg b/Documentation/hwmon/f71882fg
new file mode 100644
index 000000000000..a8321267b5b6
--- /dev/null
+++ b/Documentation/hwmon/f71882fg
@@ -0,0 +1,89 @@
+Kernel driver f71882fg
+======================
+
+Supported chips:
+  * Fintek F71882FG and F71883FG
+    Prefix: 'f71882fg'
+    Addresses scanned: none, address read from Super I/O config space
+    Datasheet: Available from the Fintek website
+  * Fintek F71862FG and F71863FG
+    Prefix: 'f71862fg'
+    Addresses scanned: none, address read from Super I/O config space
+    Datasheet: Available from the Fintek website
+  * Fintek F8000
+    Prefix: 'f8000'
+    Addresses scanned: none, address read from Super I/O config space
+    Datasheet: Not public
+
+Author: Hans de Goede <hdegoede@redhat.com>
+
+
+Description
+-----------
+
+Fintek F718xxFG/F8000 Super I/O chips include complete hardware monitoring
+capabilities. They can monitor up to 9 voltages (3 for the F8000), 4 fans and
+3 temperature sensors.
+
+These chips also have fan controlling features, using either DC or PWM, in
+three different modes (one manual, two automatic).
+
+The driver assumes that no more than one chip is present, which seems
+reasonable.
+
+
+Monitoring
+----------
+
+The Voltage, Fan and Temperature Monitoring uses the standard sysfs
+interface as documented in sysfs-interface, without any exceptions.
+
+
+Fan Control
+-----------
+
+Both PWM (pulse-width modulation) and DC fan speed control methods are
+supported. The right one to use depends on external circuitry on the
+motherboard, so the driver assumes that the BIOS set the method
+properly.
+
+There are 2 modes to specify the speed of the fan, PWM duty cycle (or DC
+voltage) mode, where 0-100% duty cycle (0-100% of 12V) is specified. And RPM
+mode where the actual RPM of the fan (as measured) is controlled and the speed
+gets specified as 0-100% of the fan#_full_speed file.
+
+Since both modes work in a 0-100% (mapped to 0-255) scale, there isn't a
+whole lot of a difference when modifying fan control settings. The only
+important difference is that in RPM mode the 0-100% controls the fan speed
+between 0-100% of fan#_full_speed. It is assumed that if the BIOS programs
+RPM mode, it will also set fan#_full_speed properly, if it does not then
+fan control will not work properly, unless you set a sane fan#_full_speed
+value yourself.
+
+Switching between these modes requires re-initializing a whole bunch of
+registers, so the mode which the BIOS has set is kept. The mode is
+printed when loading the driver.
+
+Three different fan control modes are supported; the mode number is written
+to the pwm#_enable file. Note that not all modes are supported on all
+chips, and some modes may only be available in RPM / PWM mode on the F8000.
+Writing an unsupported mode will result in an invalid parameter error.
+
+* 1: Manual mode
+  You ask for a specific PWM duty cycle / DC voltage or a specific % of
+  fan#_full_speed by writing to the pwm# file. This mode is only
+  available on the F8000 if the fan channel is in RPM mode.
+
+* 2: Normal auto mode
+  You can define a number of temperature/fan speed trip points, which % the
+  fan should run at at this temp and which temp a fan should follow using the
+  standard sysfs interface. The number and type of trip points is chip
+  depended, see which files are available in sysfs.
+  Fan/PWM channel 3 of the F8000 is always in this mode!
+
+* 3: Thermostat mode (Only available on the F8000 when in duty cycle mode)
+  The fan speed is regulated to keep the temp the fan is mapped to between
+  temp#_auto_point2_temp and temp#_auto_point3_temp.
+
+Both of the automatic modes require that pwm1 corresponds to fan1, pwm2 to
+fan2 and pwm3 to fan3.
diff --git a/Documentation/hwmon/it87 b/Documentation/hwmon/it87
index 042c0415140b..659315d98e00 100644
--- a/Documentation/hwmon/it87
+++ b/Documentation/hwmon/it87
@@ -26,6 +26,10 @@ Supported chips:
     Datasheet: Publicly available at the ITE website
                http://www.ite.com.tw/product_info/file/pc/IT8718F_V0.2.zip
                http://www.ite.com.tw/product_info/file/pc/IT8718F_V0%203_(for%20C%20version).zip
+  * IT8720F
+    Prefix: 'it8720'
+    Addresses scanned: from Super I/O config space (8 I/O ports)
+    Datasheet: Not yet publicly available.
   * SiS950   [clone of IT8705F]
     Prefix: 'it87'
     Addresses scanned: from Super I/O config space (8 I/O ports)
@@ -71,7 +75,7 @@ Description
 -----------
 
 This driver implements support for the IT8705F, IT8712F, IT8716F,
-IT8718F, IT8726F and SiS950 chips.
+IT8718F, IT8720F, IT8726F and SiS950 chips.
 
 These chips are 'Super I/O chips', supporting floppy disks, infrared ports,
 joysticks and other miscellaneous stuff. For hardware monitoring, they
@@ -84,19 +88,19 @@ the IT8716F and late IT8712F have 6. They are shared with other functions
 though, so the functionality may not be available on a given system.
 The driver dumbly assume it is there.
 
-The IT8718F also features VID inputs (up to 8 pins) but the value is
-stored in the Super-I/O configuration space. Due to technical limitations,
+The IT8718F and IT8720F also features VID inputs (up to 8 pins) but the value
+is stored in the Super-I/O configuration space. Due to technical limitations,
 this value can currently only be read once at initialization time, so
 the driver won't notice and report changes in the VID value. The two
 upper VID bits share their pins with voltage inputs (in5 and in6) so you
 can't have both on a given board.
 
-The IT8716F, IT8718F and later IT8712F revisions have support for
+The IT8716F, IT8718F, IT8720F and later IT8712F revisions have support for
 2 additional fans. The additional fans are supported by the driver.
 
-The IT8716F and IT8718F, and late IT8712F and IT8705F also have optional
-16-bit tachometer counters for fans 1 to 3. This is better (no more fan
-clock divider mess) but not compatible with the older chips and
+The IT8716F, IT8718F and IT8720F, and late IT8712F and IT8705F also have
+optional 16-bit tachometer counters for fans 1 to 3. This is better (no more
+fan clock divider mess) but not compatible with the older chips and
 revisions. The 16-bit tachometer mode is enabled by the driver when one
 of the above chips is detected.
 
@@ -122,7 +126,7 @@ zero'; this is important for negative voltage measurements. All voltage
 inputs can measure voltages between 0 and 4.08 volts, with a resolution of
 0.016 volt. The battery voltage in8 does not have limit registers.
 
-The VID lines (IT8712F/IT8716F/IT8718F) encode the core voltage value:
+The VID lines (IT8712F/IT8716F/IT8718F/IT8720F) encode the core voltage value:
 the voltage level your processor should work with. This is hardcoded by
 the mainboard and/or processor itself. It is a value in volts.
 
diff --git a/Documentation/hwmon/lm70 b/Documentation/hwmon/lm70
index 2bdd3feebf53..0d240291e3cc 100644
--- a/Documentation/hwmon/lm70
+++ b/Documentation/hwmon/lm70
@@ -1,9 +1,11 @@
 Kernel driver lm70
 ==================
 
-Supported chip:
+Supported chips:
   * National Semiconductor LM70
     Datasheet: http://www.national.com/pf/LM/LM70.html
+  * Texas Instruments TMP121/TMP123
+    Information: http://focus.ti.com/docs/prod/folders/print/tmp121.html
 
 Author:
         Kaiwan N Billimoria <kaiwan@designergraphix.com>
@@ -25,6 +27,14 @@ complement digital temperature (sent via the SIO line), is available in the
 driver for interpretation. This driver makes use of the kernel's in-core
 SPI support.
 
+As a real (in-tree) example of this "SPI protocol driver" interfacing
+with a "SPI master controller driver", see drivers/spi/spi_lm70llp.c
+and its associated documentation.
+
+The TMP121/TMP123 are very similar; main differences are 4 wire SPI inter-
+face (read only) and 13-bit temperature data (0.0625 degrees celsius reso-
+lution).
+
 Thanks to
 ---------
 Jean Delvare <khali@linux-fr.org> for mentoring the hwmon-side driver
diff --git a/Documentation/hwmon/lm85 b/Documentation/hwmon/lm85
index 400620741290..a13680871bc7 100644
--- a/Documentation/hwmon/lm85
+++ b/Documentation/hwmon/lm85
@@ -164,7 +164,7 @@ configured individually according to the following options.
                       temperature. (PWM value from 0 to 255)
 
 * pwm#_auto_pwm_minctl - this flags selects for temp#_auto_temp_off temperature
-                         the bahaviour of fans. Write 1 to let fans spinning at
+                         the behaviour of fans. Write 1 to let fans spinning at
                          pwm#_auto_pwm_min or write 0 to let them off.
 
 NOTE: It has been reported that there is a bug in the LM85 that causes the flag
diff --git a/Documentation/hwmon/ltc4245 b/Documentation/hwmon/ltc4245
new file mode 100644
index 000000000000..bae7a3adc5d8
--- /dev/null
+++ b/Documentation/hwmon/ltc4245
@@ -0,0 +1,81 @@
+Kernel driver ltc4245
+=====================
+
+Supported chips:
+  * Linear Technology LTC4245
+    Prefix: 'ltc4245'
+    Addresses scanned: 0x20-0x3f
+    Datasheet:
+        http://www.linear.com/pc/downloadDocument.do?navId=H0,C1,C1003,C1006,C1140,P19392,D13517
+
+Author: Ira W. Snyder <iws@ovro.caltech.edu>
+
+
+Description
+-----------
+
+The LTC4245 controller allows a board to be safely inserted and removed
+from a live backplane in multiple supply systems such as CompactPCI and
+PCI Express.
+
+
+Usage Notes
+-----------
+
+This driver does not probe for LTC4245 devices, due to the fact that some
+of the possible addresses are unfriendly to probing. You will need to use
+the "force" parameter to tell the driver where to find the device.
+
+Example: the following will load the driver for an LTC4245 at address 0x23
+on I2C bus #1:
+$ modprobe ltc4245 force=1,0x23
+
+
+Sysfs entries
+-------------
+
+The LTC4245 has built-in limits for over and under current warnings. This
+makes it very likely that the reference circuit will be used.
+
+This driver uses the values in the datasheet to change the register values
+into the values specified in the sysfs-interface document. The current readings
+rely on the sense resistors listed in Table 2: "Sense Resistor Values".
+
+in1_input               12v input voltage (mV)
+in2_input               5v  input voltage (mV)
+in3_input               3v  input voltage (mV)
+in4_input               Vee (-12v) input voltage (mV)
+
+in1_min_alarm           12v input undervoltage alarm
+in2_min_alarm           5v  input undervoltage alarm
+in3_min_alarm           3v  input undervoltage alarm
+in4_min_alarm           Vee (-12v) input undervoltage alarm
+
+curr1_input             12v current (mA)
+curr2_input             5v  current (mA)
+curr3_input             3v  current (mA)
+curr4_input             Vee (-12v) current (mA)
+
+curr1_max_alarm         12v overcurrent alarm
+curr2_max_alarm         5v  overcurrent alarm
+curr3_max_alarm         3v  overcurrent alarm
+curr4_max_alarm         Vee (-12v) overcurrent alarm
+
+in5_input               12v output voltage (mV)
+in6_input               5v  output voltage (mV)
+in7_input               3v  output voltage (mV)
+in8_input               Vee (-12v) output voltage (mV)
+
+in5_min_alarm           12v output undervoltage alarm
+in6_min_alarm           5v  output undervoltage alarm
+in7_min_alarm           3v  output undervoltage alarm
+in8_min_alarm           Vee (-12v) output undervoltage alarm
+
+in9_input               GPIO #1 voltage data
+in10_input              GPIO #2 voltage data
+in11_input              GPIO #3 voltage data
+
+power1_input            12v power usage (mW)
+power2_input            5v  power usage (mW)
+power3_input            3v  power usage (mW)
+power4_input            Vee (-12v) power usage (mW)
diff --git a/Documentation/spi/spi-lm70llp b/Documentation/spi/spi-lm70llp
index 154bd02220b9..34a9cfd746bd 100644
--- a/Documentation/spi/spi-lm70llp
+++ b/Documentation/spi/spi-lm70llp
@@ -13,10 +13,20 @@ Description
 This driver provides glue code connecting a National Semiconductor LM70 LLP
 temperature sensor evaluation board to the kernel's SPI core subsystem.
 
+This is a SPI master controller driver. It can be used in conjunction with
+(layered under) the LM70 logical driver (a "SPI protocol driver").
 In effect, this driver turns the parallel port interface on the eval board
 into a SPI bus with a single device, which will be driven by the generic
 LM70 driver (drivers/hwmon/lm70.c).
 
+
+Hardware Interfacing
+--------------------
+The schematic for this particular board (the LM70EVAL-LLP) is
+available (on page 4) here:
+
+  http://www.national.com/appinfo/tempsensors/files/LM70LLPEVALmanual.pdf
+
 The hardware interfacing on the LM70 LLP eval board is as follows:
 
    Parallel                 LM70 LLP