5 files changed, 16 insertions, 11 deletions

diff --git a/Documentation/hwmon/adm9240 b/Documentation/hwmon/adm9240
index 35f618f32896..2c6f1fed4618 100644
--- a/Documentation/hwmon/adm9240
+++ b/Documentation/hwmon/adm9240
@@ -24,7 +24,7 @@ Authors:
     Frodo Looijaard <frodol@dds.nl>,
     Philip Edelbrock <phil@netroedge.com>,
     Michiel Rook <michiel@grendelproject.nl>,
-    Grant Coady <gcoady@gmail.com> with guidance
+    Grant Coady <gcoady.lk@gmail.com> with guidance
         from Jean Delvare <khali@linux-fr.org>
 
 Interface
diff --git a/Documentation/hwmon/f71805f b/Documentation/hwmon/f71805f
index 28c5b7d1eb90..2ca69df669c3 100644
--- a/Documentation/hwmon/f71805f
+++ b/Documentation/hwmon/f71805f
@@ -17,7 +17,7 @@ Thanks to Kris Chen from Fintek for answering technical questions and
 providing additional documentation.
 
 Thanks to Chris Lin from Jetway for providing wiring schematics and
-anwsering technical questions.
+answering technical questions.
 
 
 Description
diff --git a/Documentation/hwmon/k8temp b/Documentation/hwmon/k8temp
index bab445ab0f52..30d123b8d920 100644
--- a/Documentation/hwmon/k8temp
+++ b/Documentation/hwmon/k8temp
@@ -2,7 +2,7 @@ Kernel driver k8temp
 ====================
 
 Supported chips:
-  * AMD K8 CPU
+  * AMD Athlon64/FX or Opteron CPUs
     Prefix: 'k8temp'
     Addresses scanned: PCI space
     Datasheet: http://www.amd.com/us-en/assets/content_type/white_papers_and_tech_docs/32559.pdf
@@ -13,10 +13,13 @@ Contact: Rudolf Marek <r.marek@sh.cvut.cz>
 Description
 -----------
 
-This driver permits reading temperature sensor(s) embedded inside AMD K8 CPUs.
-Official documentation says that it works from revision F of K8 core, but
-in fact it seems to be implemented for all revisions of K8 except the first
-two revisions (SH-B0 and SH-B3).
+This driver permits reading temperature sensor(s) embedded inside AMD K8
+family CPUs (Athlon64/FX, Opteron). Official documentation says that it works
+from revision F of K8 core, but in fact it seems to be implemented for all
+revisions of K8 except the first two revisions (SH-B0 and SH-B3).
+
+Please note that you will need at least lm-sensors 2.10.1 for proper userspace
+support.
 
 There can be up to four temperature sensors inside single CPU. The driver
 will auto-detect the sensors and will display only temperatures from
diff --git a/Documentation/hwmon/smsc47m1 b/Documentation/hwmon/smsc47m1
index c15bbe68264e..04a11124f667 100644
--- a/Documentation/hwmon/smsc47m1
+++ b/Documentation/hwmon/smsc47m1
@@ -2,12 +2,14 @@ Kernel driver smsc47m1
 ======================
 
 Supported chips:
-  * SMSC LPC47B27x, LPC47M10x, LPC47M13x, LPC47M14x, LPC47M15x and LPC47M192
+  * SMSC LPC47B27x, LPC47M112, LPC47M10x, LPC47M13x, LPC47M14x,
+    LPC47M15x and LPC47M192
     Addresses scanned: none, address read from Super I/O config space
     Prefix: 'smsc47m1'
     Datasheets:
         http://www.smsc.com/main/datasheets/47b27x.pdf
         http://www.smsc.com/main/datasheets/47m10x.pdf
+        http://www.smsc.com/main/datasheets/47m112.pdf
         http://www.smsc.com/main/tools/discontinued/47m13x.pdf
         http://www.smsc.com/main/datasheets/47m14x.pdf
         http://www.smsc.com/main/tools/discontinued/47m15x.pdf
diff --git a/Documentation/hwmon/w83627ehf b/Documentation/hwmon/w83627ehf
index fae3b781d82d..caa610a297e8 100644
--- a/Documentation/hwmon/w83627ehf
+++ b/Documentation/hwmon/w83627ehf
@@ -26,7 +26,7 @@ fan control mode).
 Temperatures are measured in degrees Celsius and measurement resolution is 1
 degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when
 the temperature gets higher than high limit; it stays on until the temperature
-falls below the Hysteresis value.
+falls below the hysteresis value.
 
 Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
 triggered if the rotation speed has dropped below a programmable limit. Fan
@@ -67,9 +67,9 @@ Thermal Cruise mode
 
 If the temperature is in the range defined by:
 
-pwm[1-4]_target    - set target temperature, unit millidegree Celcius
+pwm[1-4]_target    - set target temperature, unit millidegree Celsius
                      (range 0 - 127000)
-pwm[1-4]_tolerance - tolerance, unit millidegree Celcius (range 0 - 15000)
+pwm[1-4]_tolerance - tolerance, unit millidegree Celsius (range 0 - 15000)
 
 there are no changes to fan speed. Once the temperature leaves the interval,
 fan speed increases (temp is higher) or decreases if lower than desired.